gnirs pre-fabrication review · risk reduction overview 1045 bench design - detail description gary...
TRANSCRIPT
![Page 1: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/1.jpg)
1
Pre-Fab Review
GNIRS PRE-FABRICATION REVIEWMay 11-12, 2000
Presentation Preliminary Draft
![Page 2: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/2.jpg)
2
Pre-Fab Review
This page intentionally left blank
![Page 3: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/3.jpg)
3
Pre-Fab Review
GNIRS Pre-Fabrication ReviewTable of Contents
I. Introduction and OverviewIntroductionsAgendaOverview of Progress
II. Configuration OverviewIntroduction and OverviewConfiguration Overview/DescriptionRequirements OverviewRisk Reduction OverviewBench Design
Detail DescriptionAnalysisFab Issues
Mechanism Risk ReductionOptics Risk ReductionSoftware
III. GNIRS ManagementIV. Conclusion
![Page 4: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/4.jpg)
4
Pre-Fab Review
This page intentionally left blank
![Page 5: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/5.jpg)
5
Pre-Fab Review
GNIRS Pre-Fabrication Review
Section IIntroduction and Overview
![Page 6: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/6.jpg)
6
Pre-Fab Review
GNIRS Staff• Project management
– N. Gaughan, PM– D. Eklund, PA– M. Bowersock, AA
• Project scientist(s)– J. Elias, PS– D. Joyce, PSS– B. Gregory, PSS
• Electrical - J. Penegor, Sr. EE• SW – R. Wolff, Sr. Prog
• Mechanical– G. Muller, Sr. ME– E. Hileman, Sr. ME– L. Goble, Sr. ME
• Design Drafting– J. Andrew, Sr. TA – D. Rosin, DT– E. Downey, DT– R. Robles, DT
• Procurement – A. Davis, TA• IM – J. Stein, Sr. IM
![Page 7: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/7.jpg)
7
Pre-Fab Review
Introduction•Welcome•Orientation •Agenda•Staff introductions
–Reviewers, visitors–GNIRS Project
•PM, PS, ME, EE, SW, DT, Proc, IM
•Overview of the presentation
![Page 8: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/8.jpg)
8
Pre-Fab Review
Overview of the presentation
• We will start with the current status of the project including an overview of the project schedule, summaries of the bench design and prototyping efforts, and progress on mechanism design and software.
• The risk reduction effort is being conducted to prove the designapproaches of our two types of mechanism drives, and camera lensmounting.
• Optical bench design will discuss the solid models of the three main components of the bench: Pre-Slit, Post-Slit, and OIWFS.
• Both thermal and structural analysis of these solid models are in process. We will present preliminary results of these analyses.
• The software section will cover the software plan and software development in general.
• The management section will discuss the project schedule in detail, progress, costs, and procurement.
![Page 9: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/9.jpg)
9
Pre-Fab Review
Overview of the Presentation• Current status of the project• Project overview• Risk Reduction effort• Optical bench design and analysis• Software • Management
![Page 10: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/10.jpg)
10
Pre-Fab Review
This page intentionally left blank
![Page 11: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/11.jpg)
11
Pre-Fab Review
Review Purpose
• Assess if optical bench design will meet deflection requirement
• Review risk reduction results and assess how these results couple into the actual design
• Review scope of software effort and assess if it will meet project requirements
![Page 12: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/12.jpg)
12
Pre-Fab Review
Agenda
May 11:Time Subject Presenter0830 Introduction, opening statements Sidney/Neil0900 Technical presentation Jay
introduction and overviewConfiguration overview/description
-Benches- Mechanisms
0940 Break1000 Requirements overview Jay
Risk Reduction overview1045 Bench Design
- Detail description Gary- Analysis Ed/Gary- Fab issues Gary
1200 Lunch1300 Mechanism risk reduction Jay1400 Optics Risk Reduction Dick1445 Break1500 Software Richard1600 End of technical presentations
May 12:0900 GNIRS management Neil/Dan1100 End/Gemini caucus period1200 Lunch
![Page 13: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/13.jpg)
13
Pre-Fab Review
Agenda
• Order of presentations• Breaks• Lunch plans
![Page 14: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/14.jpg)
14
Pre-Fab Review
This page intentionally left blank
![Page 15: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/15.jpg)
15
Pre-Fab Review
Orientation and Overview
• Wall charts and posters• Work stations
– Demos of solid models of benches and other components
– Manned during breaks• Progress overview
– Project plan– Status– Projections
![Page 16: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/16.jpg)
16
Pre-Fab Review
Project Status• Systems engineering
– Prototyping of mechanism drives• Rotary drive• Linear drive• Optical mount prototype
– Cold motor testing– IFU ICD– Bench 3D solid model design– Designs are for analysis (not production)– 3 separate benches involved
• Bench analysis– Structural analysis– Thermal analysis
![Page 17: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/17.jpg)
17
Pre-Fab Review
Project Status
• Software– Software Plan– Component controller
• Overall project
![Page 18: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/18.jpg)
18
Pre-Fab Review
Project Plan Components and Phases
• Systems Engineering effort– Prototyping– Structural and thermal analysis
• Bench Design design and fab– Pre-slit bench– Post-slit bench– OIWFS bench
• Mechanism design and fab• Fixed Assemblies design and fab• Electronics design and fab• Software design, code and test/debug• Integration and test
![Page 19: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/19.jpg)
19
Pre-Fab Review
Project Plan
![Page 20: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/20.jpg)
20
Pre-Fab Review
This page intentionally left blank
![Page 21: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/21.jpg)
21
Pre-Fab Review
GNIRS Pre-Fabrication Review
Section IIConfiguration Overview
![Page 22: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/22.jpg)
22
Pre-Fab Review
This page intentionally left blank
![Page 23: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/23.jpg)
23
Pre-Fab Review
Overview
•Critical Requirements•Configuration Overview•Risk Reduction
![Page 24: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/24.jpg)
24
Pre-Fab Review
Critical Requirements Identified
•Gravity deflection - 3 requirements (from RR review and before) list - 2 affect bench– OIWFS maintains object on slit (12 microns (0.02 arcsec) motion in 1 hour)– Spectrum (slit image) doesn’t move on detector (0.1 pixel=2.7 microns in hour)– Secondary image motion at cold stop +/-1% overall (less stringent but involves interface to warm structure and to ISS)
•Thermal performance –Cool-down time (Maximum 4 days)–Temperature gradients (preservation on alignment, several degrees OK)–Temperature variations (limit flexure, defocus - need <1 K)
•Mechanism performance–Repeatability (10 pixels for reconfigurations, 0.1 pixels for acquisition)–Flexure (0.1 pixel pixel, includes mechanism “play”)–Thermal (cooling time constant, heating from motor/drive)
•Opto-mechanical performance –Lens cooling–Lens positioning (stability under thermal cycling within tolerances)–Lens stresses (500 psi or less)
![Page 25: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/25.jpg)
25
Pre-Fab Review
Critical Requirements Identified
•Gravity Deflection•Thermal Performance•Mechanism Performance•Opto-mechanical performance
![Page 26: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/26.jpg)
26
Pre-Fab Review
This page intentionally left blank
![Page 27: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/27.jpg)
27
Pre-Fab Review
Risk Reduction - Overview
•What are the risks?•How did we address them?
![Page 28: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/28.jpg)
28
Pre-Fab Review
![Page 29: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/29.jpg)
29
Pre-Fab Review
![Page 30: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/30.jpg)
30
Pre-Fab Review
Risk Reduction Plan•Systems Engineering: Systems approach used to identify areas of risk (some help from review committees!) and isolate specific issues.•Prototypes vs. analysis: Identify those issues where analysis provides good answers as opposed to those where prototyping is better. Example: use FEA for rigid structures (bench), but need prototypes to model situations where contact properties dominate effects (turrets).•Test Plans and Procedures: Prototype work designed to answer specific questions, need focussed test plan to ensure that questions are thoroughly investigated, avoid wasted effort.•Results Applied to Design: Experience with prototypes may show that a design works “as is”. May also suggest design improvements, but these are implemented only if the design would not meet requirements otherwise or redesign leads to faster schedule or lower cost.•Prototype does not need rework to meet requirements if design change to meet requirements involves minimal risk.
![Page 31: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/31.jpg)
31
Pre-Fab Review
Risk Reduction Plan
•Systems Engineering•Prototypes vs. Analysis•Test Plan and Procedures•Results Applied to Design
![Page 32: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/32.jpg)
32
Pre-Fab Review
This page intentionally left blank
![Page 33: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/33.jpg)
33
Pre-Fab Review
Risk Reduction Plan
5 Areas Involved•Flexure Analysis•Thermal Analysis•Mechanical Prototypes•Systems Approach to Design•Early Procurement
![Page 34: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/34.jpg)
34
Pre-Fab Review
This page intentionally left blank
![Page 35: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/35.jpg)
35
Pre-Fab Review
Optical Bench DesignAgenda•Design Overview•Pre-Slit Bench Assembly•Post-Slit Bench Assembly•OIWFS Bench Assembly•Fabrication Issues•Example of systems approach to design
![Page 36: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/36.jpg)
36
Pre-Fab Review
Bench Configuration Overview•Bench structure comprises
– Pre-slit bench (pick-off mirror to and including slit/IFU)– Post-slit bench (from slit to detector)– OIWFS bench (field lens to OIWFS detector)
•Mechanisms/optical assemblies– Offner relay (includes pick-off mirror)– Filter wheels– Slit/IFU slide and Decker assembly– Collimator– Acquisition mirror– Prism turret– Grating turret– Camera turret– Long camera external fold mirrors– Detector mount/focus stage
![Page 37: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/37.jpg)
37
Pre-Fab Review
Configuration Overview
Red ray: Spectrograph
Blue ray: On Instrument Wave Front Sensor
![Page 38: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/38.jpg)
38
Pre-Fab Review
This page intentionally left blank
![Page 39: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/39.jpg)
39
Pre-Fab Review
Configuration Overview
Red ray: Spectrograph
Blue ray: On Instrument Wave Front Sensor
![Page 40: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/40.jpg)
40
Pre-Fab Review
Exploded view of bench structure
•All bench structure machined from single billet.•Bench structure designed for ease of fabrication. •Machining techniques considered during design process.
Pocket depth to tool diameter ratios, radiused pockets, etc
•Stiffness obtained when components are fastened together.
![Page 41: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/41.jpg)
41
Pre-Fab Review
Exploded view of bench structure
![Page 42: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/42.jpg)
42
Pre-Fab Review
This page intentionally left blank
![Page 43: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/43.jpg)
43
Pre-Fab Review
Bench Design Drivers•Stiffness
–Minimize deflections
•Weight–Goal: Minimize weight of cold bench for minimal cool-down cycle–Weight budget
•Envelope–Fit within Gemini instrument envelope
•Mechanism access–Modular mechanisms for ease of installation/removal–Mechanisms accessible without disassembly of bench
•Motor access–Cold strapping, wiring–External to light tight bench
•Fabrication–Use proven technologies, minimize risk, optimize schedule
•Minimize bolted joints–Optimal thermal conductivity, control tolerances, homogeneous structure
![Page 44: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/44.jpg)
44
Pre-Fab Review
This page intentionally left blank
![Page 45: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/45.jpg)
45
Pre-Fab Review
Restart Review
July, 1999
Pre-Fab Review
May, 2000
GNIRS Final Assy 2000 Kg 2000 KgOptical Bench (Cold) 700 Kg 698 Kg
Pre-slit Bench - 204 Kg
Post-Slit Bench - 412 Kg
OIWFS Bench - 82 Kg
GNIRS Weight Budget
![Page 46: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/46.jpg)
46
Pre-Fab Review
This page intentionally left blank
![Page 47: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/47.jpg)
47
Pre-Fab Review
Bench Design Philosophy•Use 3D ray traces to drive mechanism/optics locations. •Design bench structure/interfaces around mechanisms/optics.•Put structure where the load path is.
•Use best engineering judgementto optimize bench design prior to analysis.
–Minimize number of iterations during analysis.
![Page 48: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/48.jpg)
48
Pre-Fab Review
This page intentionally left blank
![Page 49: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/49.jpg)
49
Pre-Fab Review
Mechanism Interface Design Philosophy
•Control interfaces using parametric design.–Example: Using tool bodies
•Support axles of rotary mechanisms at both ends for maximum stiffness.•Use dowel pins or locating surfaces for repeatable installation of mechanisms.•Use captive screws to fasten mechanisms to bench.•Use threaded inserts on all bench to mechanism interfaces.
![Page 50: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/50.jpg)
50
Pre-Fab Review
Using parametric tool bodies
•A tool body is a positive shape that gets Boolean subtracted from another shape to produce a negative of that shape.
•Parametric: Change the dimensions on the tool body and all instances of that tool body will update.
•Effective method of controlling interface accuracy between mechanisms and bench.
![Page 51: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/51.jpg)
51
Pre-Fab Review
Using parametric tool bodies
![Page 52: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/52.jpg)
52
Pre-Fab Review
Pre-Slit Bench Assembly
•Pick off mirror•Offner relay•Filter wheel•Decker slide•Slit & IFU slide
![Page 53: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/53.jpg)
53
Pre-Fab Review
Pre-Slit Bench Assembly
![Page 54: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/54.jpg)
54
Pre-Fab Review
Pre-Slit Bench Assembly
•Fore-optics mirror access through covers.•Filter access achieved by removing filter wheel assembly.•Slit module and IFU module access achieved by driving slit slide to access port and removing covers.•Decker slide has no serviceable parts.
![Page 55: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/55.jpg)
55
Pre-Fab Review
Pre-Slit Bench AssemblyDesign Features•Component accessibility without disassembly
–Fore optics Mirrors –Filter wheel –Slit module–IFU modules
•Drive motors mounted externally–External to light tight bench
•Modular design–Removable as an assembly
![Page 56: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/56.jpg)
56
Pre-Fab Review
Post-Slit Bench Assembly
•Collimator mirror: Mount is integral part of post-slit bench•Acquisition mirror: Mounts from bottom of post-slit bench•Prism turret: Mounts to bottom of post-slit bench•Grating turret: Mounts to side of post-slit bench•Camera turret: Post-slit bench is support housing•Long camera fold mirror housing•Detector/focus mechanism: Mounts to side of post-slit bench
![Page 57: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/57.jpg)
57
Pre-Fab Review
Post-Slit Bench Assembly
![Page 58: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/58.jpg)
58
Pre-Fab Review
Post-Slit Bench Assembly
•Remove covers to access components
![Page 59: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/59.jpg)
59
Pre-Fab Review
Post-Slit Bench AssemblyDesign Features•Component accessibility without disassembly
–Collimator mirror–Acquisition mirror–Prism turret–Grating turret–Camera turret–Detector–Camera fold mirrors
•Drive motors mounted externally–External to light tight bench
•Good thermal conductivity by minimizing bolted joints
![Page 60: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/60.jpg)
60
Pre-Fab Review
This page intentionally left blank
![Page 61: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/61.jpg)
61
Pre-Fab Review
OIWFS Bench Assembly
![Page 62: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/62.jpg)
62
Pre-Fab Review
OIWFS Bench Assembly
•Wave front sensor bench hog out and field lens support tube
•Modular: Bolt in IFA hardware and align separately
•OIWFS bolts to post-slit bench only
•Field lens support tube clamped to post-slit bench
•No mechanical connections to pre-slit bench
•Labyrinth light seal between field lens support tube and pre-slit bench
![Page 63: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/63.jpg)
63
Pre-Fab Review
OIWFS Bench AssemblyDesign Features•Modular design
–Align wave front sensor independently of spectrograph
•Mechanically interfaces with post-slit bench only•Use IFA components
–Field lens–Combo lens mount–Gimbal mirror–Filter wheel–Detector/focus mechanism
•Interfaces to IFA supplied components are according to ICD
![Page 64: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/64.jpg)
64
Pre-Fab Review
This page intentionally left blank
![Page 65: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/65.jpg)
65
Pre-Fab Review
Fabrication Issues (1)Design Considerations/Conclusions•Investigated Castings, Hog-outs, Weldments•Rejected Castings
–CTE mismatches between cast and machined components
•Rejected Weldments–Requires many welding fixtures–Warping issues
•Selected Hog-outs–Uniform CTE’s–Utilize CNC machining techniques –Less fixturing, more expeditious
![Page 66: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/66.jpg)
66
Pre-Fab Review
This page intentionally left blank
![Page 67: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/67.jpg)
67
Pre-Fab Review
Fabrication Issues (2)Minimize fabrication risks•CNC machine and stress relieve critical components.
–Reliable, known, technology has been used extensively at NOAO.–Use uphill quench technique–Tool paths defined by 2D drawing or 3D solid models.
•Fabricate all critical parts from a single billet.–Ensure material uniformity
•Vendor qualification.
![Page 68: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/68.jpg)
68
Pre-Fab Review
Machine critical structure from one billet
•Rough machine, stress relieve and anodize, final machine
•Orient critical components in same direction on billet for uniformity
•Witness samples taken on both ends of billet to verify uniformity of billet
![Page 69: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/69.jpg)
69
Pre-Fab Review
Machine critical structure from one billet•Material: 6061-T6 Aluminum
•Largest component duplicated in layout for contingencies
•CTE measurements on witness samples -Characterize CTE in 3 axes at 2 locations
•Material has been purchased
![Page 70: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/70.jpg)
70
Pre-Fab Review
This page intentionally left blank
![Page 71: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/71.jpg)
71
Pre-Fab Review
Procurement
•1 FTE assigned to procurement•Purchasing parts•Tracking parts through fabrication•Inventory control•Vendor qualification •Inspection
![Page 72: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/72.jpg)
72
Pre-Fab Review
This page intentionally left blank
![Page 73: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/73.jpg)
73
Pre-Fab Review
Systems approach to design3:1 Drive Motor Module
Requirements•Standardize on one motor•Common electrical connections •Motors to be thermally isolated•All motors to be light sealed from bench •Common interface with mechanisms/bench•Ease of installation, alignment, removal
![Page 74: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/74.jpg)
74
Pre-Fab Review
3:1 Drive Motor Module Used on:•Decker slide
•Slit slide
•Prism turret
•Grating turret
•Camera turret
•Detector focus drive
![Page 75: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/75.jpg)
75
Pre-Fab Review
![Page 76: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/76.jpg)
76
Pre-Fab Review
This page intentionally left blank
![Page 77: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/77.jpg)
77
Pre-Fab Review
Cold Bench Assembly Rigidity Requirements:
•Image de-center at detector due to flexure between slit and detector to be < 2.7 micron (.000107”)during 1 hour.
•Differential flexure between OIWFS and spectograph slit shall not cause image decenter at slit > than 12 micron (.000472”) in 1 hour.
![Page 78: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/78.jpg)
78
Pre-Fab Review
This page intentionally left blank
![Page 79: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/79.jpg)
79
Pre-Fab Review
Analysis Tools
• MSC Nastran Finite Element Analysis to determine structural deformation under gravity loads.
• ZEMAX Optical Analysis package for structural to optical influence matrix.
• MathCad document synthesizing results of the two.
![Page 80: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/80.jpg)
80
Pre-Fab Review
This page intentionally left blank
![Page 81: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/81.jpg)
81
Pre-Fab Review
• For expediency, use tetrahedral meshing from imported solids created in mechanical desktop.
– Ran test cases to determine accuracy of tetrahedral mesh vs. mesh of plate elements.
– Compare model sizes, estimate solve time.
• Merge nodes at bolted interface surfaces.
– Ensure design incorporates sufficient fasteners.
FEA methodology
![Page 82: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/82.jpg)
82
Pre-Fab Review
This page intentionally left blank
![Page 83: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/83.jpg)
83
Pre-Fab Review
Tetrahedral mesh vs. plate mesh performance
• Comparison of 12”x12”x1/4” and 18”x6”x1/4” aluminum plates with 1/4” element size.
• Transversely loaded plate: deflection agrees within 1% between models and with theoretical solution. DOF = 149,284 for tetrahedral DOF = 25,091 for plate
• Shear deformed plate: deflection agrees within 1%.
![Page 84: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/84.jpg)
84
Pre-Fab Review
This page intentionally left blank
![Page 85: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/85.jpg)
85
Pre-Fab Review
FEA model of Cold Bench Assembly• Constrained along three faces.• Load cases are gravity in X, Y, Z directions.• Model size: ______ nodes, ______ elements, ______ DOF.• Solve time: ___ hours
![Page 86: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/86.jpg)
86
Pre-Fab Review
This page intentionally left blank
![Page 87: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/87.jpg)
87
Pre-Fab Review
Bench Assembly Deformed Shape
• Load Case: -1 g in the Y direction.
• Plotted Scale multiplier = x1000
• Plotted Units: Inches
• .0001” = 2.54 microns
![Page 88: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/88.jpg)
88
Pre-Fab Review
This page intentionally left blank
![Page 89: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/89.jpg)
89
Pre-Fab Review
Image De-center at Detector due to Unit Gravity Loading:
• 1 G in the X direction = ______ microns.• 1 G in the Y direction = ______ microns.• 1 G in the Z direction = ______ microns.
![Page 90: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/90.jpg)
90
Pre-Fab Review
This page intentionally left blank
![Page 91: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/91.jpg)
91
Pre-Fab Review
Thermal Analysis
•Passive Design Optimizes Thermal Performance
•Bench Thermal Control Provided•Extensive Analysis Not Required
![Page 92: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/92.jpg)
92
Pre-Fab Review
Thermal Design[Facing Page]The design minimizes impact of thermal requirements on structure.•During cool-down, most of the heat is removed by the pre-cool system, which is routed so that thermal paths from the structure and mechanisms to the pre-cool attachment points are short (~50 cm or less).•During operation (steady state), the design minimizes heat input into the bench and heat flow through the bench. Heat flow is through the active radiation shield (radiation loads) or through cold-strapping (motors, cold-stationing of wires). Dominant source of heat input into bench should be radiation through dewar window.•Thermal control of bench allows bench temperature to be stable even with varying loads into cryo-coolers.•Extensive analysis is not required since the design minimizes the heat input into the bench, so that gradients or variations in gradients will be very small.
![Page 93: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/93.jpg)
93
Pre-Fab Review
Thermal Design
Design minimizes impact of thermal requirements on structure•Cool-down time•Temperature gradients•Temperature stability
![Page 94: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/94.jpg)
94
Pre-Fab Review
Thermal Analysis
Facing PageCool-down time <4 days is met by design, limited analysis needed to demonstrate this. Cold mass budget has been stable over past 10 months.•Liquid nitrogen pre-cool system cools to approximately 80K; routing provides short thermal paths for structure; bench structure design thus constrained by flexure requirements only.•4 cryocooler heads provide cooling power to get from 80K to 60K rapidly.•Bench temperaturel control allows rapid stabilization of bench temperature at nominal value, avoid long cooling “tail” common with cryocoolers.
![Page 95: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/95.jpg)
95
Pre-Fab Review
Thermal Analysis
Cool-down time <4 days•Liquid nitrogen pre-cool system•4 cryocooler heads•Bench temperature control
![Page 96: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/96.jpg)
96
Pre-Fab Review
Thermal AnalysisFacing PageGradients are limited by design, only limited analysis needed to demonstrate this. Note that requirement to limit temperature gradient variations is more stringent than limitations on either temperature stability or temperaturel gradients – see next item.•Gradient along bench to collimator produces defocus of ~8 microns/K maximum; defocus due to 2% CTE variation (6061) may be 120 microns (I.e. equivalent to 15K gradient). Some warm to cold adjustment (shim adjustment) will probably be needed.•Active shield decoupled from bench structure. Most heat inputs go into active shield (radiation, cold-station wires, bench supports), then to coolers, and bypass bench. Gradients in shield not a concern. Forward baffle tied to shield, not bench to minimize heat input into bench through window.•Motors potentially major heat input (instantaneous power = radiation load), so are isolated from bench and coupled to cryocoolers. Requires motors be external to bench (radiation from motors an issue as well).
![Page 97: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/97.jpg)
97
Pre-Fab Review
Thermal Analysis
Gradients negligible•Active shield•Motors decoupled from structure
![Page 98: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/98.jpg)
98
Pre-Fab Review
Thermal AnalysisFacing PageTemperature variations are limited by design, limited analysis needed to demonstrate this. Note that requirement to limit gradient variations is main concern.•Variations in collimator temperature relative to bench produce defocus of ~8 microns/K of temperature change.•Variations in temperature gradients across turret supports may produce tilts of several microrad/degree of temperature difference; may be less depending on geometry.•Active shield decoupled from bench structure. Most heat inputs go into active shield (radiation, cold-station wires, bench supports), then to coolers, and bypass bench. Gradients in shield not a concern. Radiation inputs vary by ~40% so must minimize graidents they produce in the bench.•Motors potentially major variable heat input (instantaneous power= radiation load, while average power very small), so are isolated from bench and coupled to cryocoolers. Requires motors be external to bench (radiation issues as well). Motors not tied to mechanism supports so these don’t become heat paths and develop gradients.•Bench temperature control allows stabilization of bench temperature at nominal value, allows heat input from active shield into coolers to vary without pulling bench along.
![Page 99: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/99.jpg)
99
Pre-Fab Review
Thermal Analysis
Thermal variations minimal•Active shield•Isolate motors•Bench thermal control
![Page 100: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/100.jpg)
100
Pre-Fab Review
This page intentionally left blank
![Page 101: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/101.jpg)
101
Pre-Fab Review
Optics Risk Reduction
• Optics mount prototype (BK7 lens)• Early procurement• Acceptance testing• Light leak/ baffling analysis• Cross-check ray trace with bench
design
![Page 102: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/102.jpg)
102
Pre-Fab Review
![Page 103: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/103.jpg)
103
Pre-Fab Review
Optics Mount Design
•Three axial seats (conic)•Spring-loaded axial preload•Two fixed, one compliant radial seat
–Provide radial preload–Allow for differential thermal contraction of lens, mount
![Page 104: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/104.jpg)
104
Pre-Fab Review
Optics Mount Requirements
• The camera elements must be held to tolerances of ~20 µm(axial), 20 µm (radial), and ZZ mrad in tilt. The radial and axial seats may be final machined after the optics are received and tested.
• CTE of 6061 Al lens mount is greater than that of lens, and it will cool first. As the lens cools, the radial preload must keep thelens against the seats.
• The optics must attain ~ 60 K within the four-day cooldownrequirement
• Contact between the lens and its mount must minimize risk of damage to the lens resulting from physical stress or large thermal gradients
![Page 105: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/105.jpg)
105
Pre-Fab Review
Optics Mount Requirements
•Secure optics in proper location•Maintain location when cold•Ensure timely cooling•Minimize risk of damage
![Page 106: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/106.jpg)
106
Pre-Fab Review
Prototype Test Plan• A number of tests are initially done at room temperature
– Assembly and fit check– Adjustment of preloads to design values– Measurement of friction, preload operation in different orientations
with respect to gravity– Repeat tests after thorough cleaning of components
• Initial cooling tests to measure preload operation– Temperature sensors installed on lens– Observe fiducial marks on lens and mount for differential motion as
lens is cooled• Second tests to measure lens cooling
– Lens covered to eliminate ambient IR radiation– 1 W heaters on mount & lens for measuring properties
![Page 107: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/107.jpg)
107
Pre-Fab Review
Prototype Tests• Ambient Temperature• Cold Tests - 1
– Positional repeatability
• Cold Tests - 2– Cooling time– Thermodynamic properties– Model thermal behavior
![Page 108: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/108.jpg)
108
Pre-Fab Review
Ambient Temperature Tests• Proper preload achieved using stock springs, tailored shims,
adjustments (interchangable)• Thorough cleaning of components resulted in dramatic increase
in friction between lens and mount– Preload force insufficient to return lens against radial or axial seats
after a small displacement– Apparent abrasion of Al mount by lens
• Results– Polish axial, radial seats to remove machining marks, burrs– Install Kapton tape on axial, radial seats to reduce friction– Friction now reduced so lens returns to initial position after small
displacement, even against gravity– Continue to cold test phase
![Page 109: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/109.jpg)
109
Pre-Fab Review
Ambient Tests
• Axial, radial spring forces• Coefficient of friction before/after
cleaning• Restoring against displacements• Kapton tape reduces friction at seats
![Page 110: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/110.jpg)
110
Pre-Fab Review
![Page 111: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/111.jpg)
111
Pre-Fab Review
Cold Tests (1)
• Different CTE of lens, mount results in differential motion during cooldown
• Measure relative positions of lens and mount over a thermal cycle– Optical fiducials on lens and mount– TLENS ~ 150 K
• Measurements consistent with proper preload function
![Page 112: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/112.jpg)
112
Pre-Fab Review
![Page 113: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/113.jpg)
113
Pre-Fab Review
Cold Tests (2)• TLENS vs time
– Lens shielded from ambient radiation– Continuous evacuation of cryostat
• Heater tests– Thermodynamic properties at ~ 80 K
• Model calculations– Radiative coupling– Conduction (direct, sensor wires)
![Page 114: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/114.jpg)
114
Pre-Fab Review
Prototype Test Conclusions
• Kapton tape on lens seats is required to reduce friction• Differential motion of lens and mount during cooling is
consistent with proper operation of radial preload• When shielded from ambient radiation and conduction, lens
cools to mount temperature in ~ 30 hours– Both radiative and conductive cooling are important– Kapton probably increases cooling time, but it is still acceptable– Similar mount scheme for prisms should yield acceptable cooling
• Risk of damage should be small– Overaggressive cooling can induce stress fracture (cooling plugs in
prisms may pose a danger in this respect)– Kapton tape may act as thermal buffer– Anticipated cooling rate of GNIRS camera should not impose large
thermal gradients in lenses
![Page 115: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/115.jpg)
115
Pre-Fab Review
Prototype Test Conclusions
• Preloads function properly at low temperature
• Cooling of lens acceptable• Cross-disperser elements• Risk of damage minimal
![Page 116: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/116.jpg)
116
Pre-Fab Review
Optics Procurement and Testing
• Optical elements can be long lead-time items. We have initiated procurement to permit delivery well ahead of needs, with significant allowance for contingency.– RMI (camera lenses)– II-VI (powered mirrors)– Spectronics (gratings)– Filters (NDC/IR Engineering)
• NOAO has skilled in-house opticians to ensure quality control of vendor products– In-process inspection of optical material at vendor site– Witness acceptance testing of optics at vendor site– Perform in-house inspection at NOAO prior to acceptance
![Page 117: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/117.jpg)
117
Pre-Fab Review
Optics Procurement & Testing
• Early procurement of optics components• In-process inspections of optics• Acceptance testing
– Vendor site– In-house
![Page 118: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/118.jpg)
118
Pre-Fab Review
Baffling and Light Leaks
• Bench will be light-tight structure (excepting entrance aperture)– Step / labyrinth seals on cover plates and interface joints– Cryomotor feedthrough designed to be light-tight
• 3-dimensional design yields optics footprint throughout bench– Design baffles to fit footprint– Some optical analysis required for critical locations (Offner)– Investigate appropriate materials for baffles
• Some vignetting in cross-dispersed mode (short blue camera)– Occurs only at extremal wavelengths (short end of m=6 @ 0.95 µm
[1.5%]; long end of m=3 @ 2.53 µm [0.5%])– Mitigating factors: higher blaze efficiency at 0.95 µm in 7th order;
low transmission of SF57 cross-dispersion prism at 2.53 µm
![Page 119: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/119.jpg)
119
Pre-Fab Review
Baffling & Light Leaks
• Labyrinth, angle seals at joints• Motor interface• Baffles at appropriate locations• 3-d design provides optics footprint
![Page 120: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/120.jpg)
120
Pre-Fab Review
Risk Reduction - Prototypes
•Cold Motor Testing•Rotary Prototype Mechanism•Linear Prototype Mechanism•Optics Mount Prototype
![Page 121: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/121.jpg)
121
Pre-Fab Review
Mechanism Risk Reduction
Cold Motors•Identify suitable motor•Specify operating parameters
![Page 122: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/122.jpg)
122
Pre-Fab Review
Mechanism Risk ReductionFacing PageCold Motors - Objectives and results•Identify suitable motor. Phytron series 52 identified (same as NIRI). Examined API, smaller Phytron (series 42) motors, but these did not appear able to run for long periods at required speeds (600 rpm+)•Specify operating parameters. Require that motors be operable continuously without control of cuty cycle. Motors cannot be run at full power at higher speeds for extended periods (minutes). Power must be limited to 10W or less for continuous operation, which limits torque available (roughly 7 oz-in at 600 rpm). Can run faster at lower torque, slower with higher torque. Implies mechanism drive torques <7 oz-in, ideally <3 oz-in.
![Page 123: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/123.jpg)
123
Pre-Fab Review
Mechanism Risk ReductionRotary Prototype Mechanism•Model for 3 turrets•Addresses flexure (tilt most critical), drive performance, thermal performance•Additional prototyping
![Page 124: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/124.jpg)
124
Pre-Fab Review
Mechanism Risk Reduction
Rotary Prototype Objectives•Repeatability•Flexure•Torque•Cooling time•Motor Heating
![Page 125: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/125.jpg)
125
Pre-Fab Review
Mechanism Risk ReductionFacing PageRotary Prototype Objectives•Mechanism to be repeatable to 0.035 mrad (drive reduction set to make this 1/2 motor step)•Mechanism flexure to be <1 microrad tilt under 1g. Displacements can be much larger, not an issue.•Torque <7 oz-in, ideally <<7 oz-in due to motor properties•Cooling time needs to be a few hours so mechanism will track bench•Motor heating. Motor deliberately not isolated in order to compare heating effects with models.
![Page 126: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/126.jpg)
126
Pre-Fab Review
![Page 127: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/127.jpg)
127
Pre-Fab Review
Mechanism Risk ReductionFacing PageRotary Prototype Description•Rotating barrel similar in mass, size to prism and grating turrets•540:1 reduction same as that for prism and grating turrets•Backlash allowed (expected)•Temperature sensors, including one on barrel (won’t do this in GNIRS)•22-bit encoder on barrel•Motor mounted directly on base-plate•Provisions for manual operation (external feed-through on dewar)•Tests in 2 orientations possible
![Page 128: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/128.jpg)
128
Pre-Fab Review
Mechanism Risk Reduction
Rotary Prototype Results•Repeatability 0.2 motor steps•Flexure >10 microrad (more work)•Torque <2 oz-in•Cooling time•Motor Heating
![Page 129: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/129.jpg)
129
Pre-Fab Review
Mechanism Risk ReductionFacing PageRotary Prototype Results•Observed repeatability (measured at encoder) is ~0.2 motor steps rms (>2x better than requirements) •Mechanism flexure is >10 microrad - need further work (discussed below).•Torque <2 oz-in, well within requirements - may be able to run faster (900 rpm).•Cooling time•Motor heating. Temperature gradient across baseplate, compare with model prediction.
![Page 130: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/130.jpg)
130
Pre-Fab Review
Mechanism Risk Reduction
Rotary Prototype Additional Work
•Flexure >10 microrad (more work)•Prototype improved bearing/pre-load designs
![Page 131: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/131.jpg)
131
Pre-Fab Review
Bearing Test Prototype #1• Section view
• Timken tapered rollers against aluminum races.
• Preload flexure removes endplay and radial clearance.
![Page 132: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/132.jpg)
132
Pre-Fab Review
Bearing Test Prototype #1
Facing PageRotary Prototype Bearing Prototype #1 Description•Tapered roller bearings to maximize contact for thermal conduction, wear, deflection•Spring-loaded with flexure to provide pre-load•Bearing locations design to produce equal deflections (zero tilt) under gravity•Aluminum races (contact surfaces) provide essentially athermal design; large contact area should minimize wear; rollers are chrome-plated steel•Test flexure and torque•If performance satisfactory, stop here
![Page 133: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/133.jpg)
133
Pre-Fab Review
Bearing Test Prototype #2
• Section view
• Precision angular contact bearings on 440C races.
• Preload flexure removes endplay and radial clearance.
![Page 134: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/134.jpg)
134
Pre-Fab Review
Bearing Test Prototype #2
Facing PageRotary Prototype Bearing Prototype #2 Description•Stainless steel angular contact bearings to provide good performance in terms of wear, corrosion, repeatability.•Spring-loaded with flexure to provide pre-load•Bearing locations design to produce equal deflections (zero tilt) under gravity•Bearing interface uses Invar plug, flexures to match average contraction of bearing seat and shaft to bearing•Test flexure and torque
![Page 135: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/135.jpg)
135
Pre-Fab Review
Mechanism Risk ReductionLinear Prototype Mechanism•Model for Slit/IFU slide•Addresses flexure (displacements most critical), drive performance, thermal performance
![Page 136: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/136.jpg)
136
Pre-Fab Review
Mechanism Risk Reduction
Linear Prototype Objectives•Repeatability•Flexure•Torque•Cooling time•Motor Heating
![Page 137: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/137.jpg)
137
Pre-Fab Review
Mechanism Risk Reduction
Facing PageLinear Prototype Objectives•Mechanism to be repeatable to 1 micron in direction of motion (drive reduction set to make this 1/2 motor step)•Mechanism flexure to be <4 microns in direction of motion under 1 g. Tilts must keep displacements at different slit locations under this value - typically <1 mrad.•Torque <7 oz-in, ideally <<7 oz-in due to motor properties•Cooling time needs to be a few hours so mechanism will track bench•Motor heating. Motor isolated in order to test isolation calculations/design.
![Page 138: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/138.jpg)
138
Pre-Fab Review
![Page 139: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/139.jpg)
139
Pre-Fab Review
Mechanism Risk ReductionFacing PageLinear Prototype Description•Slide similar in mass, size to slit/IFU slide•Slide moves on 4 rollers with top pre-load roller & spring arm•Counterweight with idler•Spring-loaded split screw drives half-nut on slide (zero backlash)•Reduction same as that for slide•Backlash allowed (expected) ahead of split screw (30:1 reduction)•Temperature sensors, including one on slide (won’t do this in GNIRS)•22-bit encoder on slide•Motor mounted with thermal isolation; thermal sensors on either side of isolation•Provisions for manual operation (external feed-through on dewar)•Tests in 2 orientations possible
![Page 140: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/140.jpg)
140
Pre-Fab Review
Mechanism Risk Reduction
Linear Prototype Results•Repeatability •Flexure•Torque 4-5 oz-in - design change•Cooling time•Motor isolation
![Page 141: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/141.jpg)
141
Pre-Fab Review
Mechanism Risk ReductionFacing PageLinear Prototype Results
![Page 142: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/142.jpg)
142
Pre-Fab Review
Risk Reduction - ProcurementEarly procurement (not “just in time”) for critical items:•Powered Mirrors (II-VI)•Lenses (RMI)•Filters (NDC/IR Engineering)•Gratings (master rulings: Spectronics)•Large Al 6061 Billet (for bench: Bechdon)
![Page 143: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/143.jpg)
143
Pre-Fab Review
Risk Reduction - Isolate Sub-Systems
Integral Field Unit•Each IFU is single module•Installs via access port•Interfaces controlled by ICD
![Page 144: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/144.jpg)
144
Pre-Fab Review
![Page 145: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/145.jpg)
145
Pre-Fab Review
Risk Reduction - Isolate Sub-Systems
On-Instrument WFS•Installs on its own bench structure•Separate electronics•Interfaces controlled by ICD
![Page 146: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/146.jpg)
146
Pre-Fab Review
Risk Reduction - Isolate Sub-Systems
On-Instrument WFSFacing PageSeparate bench and electronics allow functionality and internal alignment of OIWFS to be verified independent of spectrograph functions. Interactions required are alignment of OIWFS to spectrograph slit (mainly focus) and communications interface (software).
![Page 147: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/147.jpg)
147
Pre-Fab Review
This page intentionally left blank
![Page 148: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/148.jpg)
148
Pre-Fab Review
GNIRS Software
•Requirements
•Software Development Plan
•Schedule and Status
![Page 149: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/149.jpg)
149
Pre-Fab Review
Software Requirements
Area Examples
ICD 1.9.b/3.1
Instrument Sequencer interface software Integrates OIWFS, detector controller and CC, using EPICS and ‘C’.
Engineering interface (screens) Use DM (display manager)Allow for verification of compliance with Gemini OCS interfaceJog motors (command line, during engineering/test phase)
Simulation mode(s) Simulate instrument functions – 3 modes
Control mechanism motors Datum at home positionMove motors simultaneouslyBacklash compensation
Control instrument functions On-off cyrocooler controlControl dewar heaters
Monitor instrument functions Sense limit switch activationsRead/report temperature and pressureRead/report dewar internal pressure
Configuration Allow user to specify filter combinations by namesMotor motion parameters not compiled into code
Hardware No encodersDigital I/O required for some motor controlTest/use backup switches
![Page 150: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/150.jpg)
150
Pre-Fab Review
Software Requirements
Multiple Sources:• ICD’s
– Gemini– User (1.9.b/3.1)– OIWFS, GNAAC
• Engineering Interface• Hardware
![Page 151: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/151.jpg)
151
Pre-Fab ReviewSoftware Derived Requirements
Area Example
Motor drive
Ability to boost motors to overcome starting frictionAbility to vary motor speeds (rates)How to approach HOME positionBacklash-removal “dance”
Position labels Linked listsConfiguration file format
Unit TransformationsConvert desired positions to motor stepsIllegal positions imply CAR placed in ERROR stateConvert volts to degrees K, C
Testing Log data, and in format suitable for trend analysisIntegrate CA with scripting to control full instrument
DHSWCS
A/V pairs for headersModify/pass WCS information
Thin layer EPICS Provide command line control as well as DM and OCS interfacesSemaphores for control of CAD states
![Page 152: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/152.jpg)
152
Pre-Fab Review
Software Derived Requirements
These, in turn, come from
• Software Requirements
• Internal Hardware Details
• Software Design Decisions
• ...
![Page 153: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/153.jpg)
153
Pre-Fab Review
This page intentionally left blank
![Page 154: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/154.jpg)
154
Pre-Fab Review
Software Development Phases
• Component controller software• Lab support software• Detector interface software• Test and debug• EPICS software
![Page 155: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/155.jpg)
155
Pre-Fab Review
ICD’s: One major ICD: 1.9.b/3.1, OIWFS ICD, Detector Controller ICD
Infrastructure: System code module. System initialization, allocation of structures, interrupt, logging, etc.
Motor control: Code for operation of mechanisms. Interrupt driven, funnels commands to VME controllers, records status: motion complete, current position, home position, etc.
Digital I/O board: Code for I/O control of motor power, cryohead operation, etc.
Temperature board: Code for monitoring of temperature sensors throughout the instrument. Detects out of range conditions. Provides input to status/health module.
Status and Health: Checks status of motor position, limit and home switches, motor state, I/O bit states, temperatures, etc.
Simulation: Both full and fast modes can be accommodated.
Component Controller Software
![Page 156: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/156.jpg)
156
Pre-Fab Review
Component Controller Software• Infrastructure• Motor control• Low-level• High-level• Digital I/O• Temperature board• Status/health/simulation• Schedule time 3 months
![Page 157: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/157.jpg)
157
Pre-Fab Review
Scripts and Logging: Code for laboratory testing. Data collection for performance analysis. Language, if any, not yet chosen.
Baseline data: Allows detection of degraded performance.
Detector Interface: Channel access code to provide needed message stream to operate the NIRS Array Controller.
Lab Support
![Page 158: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/158.jpg)
158
Pre-Fab Review
Lab Support and Detector Interface Software
• Lab support software– Scripts– Script language– Logging– GUI
• Detector interface software– Channel access– Instrument coordination
• Schedule time 4 months
![Page 159: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/159.jpg)
159
Pre-Fab Review
This page intentionally left blank
![Page 160: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/160.jpg)
160
Pre-Fab Review
Test and Debug Requires Electronics
• Includes testing of components controller software
• Goal is to eliminate problems during instrument integration
• A software test fixture will be provided• Phased to coincide with completion of thermal
enclosure electronics• Schedule time is approximately 5 months
![Page 161: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/161.jpg)
161
Pre-Fab Review
EPICS: Intended to make minimal use of CAPFAST diagrams and containing no SNL code.
Thin layer works well with components controller.
Instrument sequencer talks to OIWFS, GNAAC, OCS and CC and so may require more elaborate use of standard EPICS.
EPICS Software
![Page 162: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/162.jpg)
162
Pre-Fab Review
EPICS Software
• Study/design• Using DM, CAPFAST• Instrument Sequencer
– OIWFS– Detector Controller
• Components controller• SAD• Schedule time 7 months
![Page 163: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/163.jpg)
163
Pre-Fab Review
This page intentionally left blank
![Page 164: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/164.jpg)
164
Pre-Fab Review
Software Organization and Data Flow
• Top level graphic• Functional Flow• Command sequences and interfaces
![Page 165: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/165.jpg)
165
Pre-Fab Review
• Uncertain portion– Instrument Sequencer– OIWFS
• Thin EPICS and Detector• Straightforward part
![Page 166: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/166.jpg)
166
Pre-Fab Review
O IW S G e m in i In te rfa c e
-- O C S -- E n g . In t e r f a c e
IR C o n t r o l l e r
T h i n E p i c s L a ye r
C o m m a n d L i n e
U N ITS /P o s i t io n C o n v e r s i o n
D i g i t a l I/O a n d M o to r C o m m a n d s
S e n d c o m m a n d s to M o to r C o n tro l le r
O p e ra te M e c h a n i s m
S ta t u s R e t u r n
In s t r u m e n t S e q u e n c e r
S ta t u s R e t u r n
S ta t u s R e t u r n
![Page 167: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/167.jpg)
167
Pre-Fab Review
This page intentionally left blank
![Page 168: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/168.jpg)
168
Pre-Fab Review
Functional Flow DiagramGemini Interface- OCS- Eng Interface
Thin EPICS Layer- No SNL- Minimal CAPFAST
Instrument Sequencer
UNITS/Position - Conversion- Validate parameters from OCS- Determine detector position- Configuration file for parameters
User Input via Command Line
OIWS
System Health System State
IR Controller
![Page 169: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/169.jpg)
169
Pre-Fab Review
This page intentionally left blank
![Page 170: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/170.jpg)
170
Pre-Fab Review
Functional Flow DiagramDigital I/O and Motor Commands- CryoHead Enable- Mechanism control
- Motor on/off- Move to position- Backlash removal
-Temperature Diode readback
Send commands to Motor Controller- Control Access- Handle Responses- Fetch Status- Timeout on Error/limit
Operate Mechanism- Command Routing- Interrupt Handling- Signals/Semaphores- Flags
- Illegal command- Limit overtravel- Done
StatusMotor PositionHome SwitchLimit Switch
Command OKI/O bits
Temperatures
Health- Good - Warning- Bad
Scripts/Logging- Support testing- Data Storage- Temps- Motor Positions
![Page 171: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/171.jpg)
171
Pre-Fab Review
Low Level Motor Control
• Interrupt driven communication • Four motors on one card • No encoders!• Handles commands that have
immediate response• Timeout marks motion failure
![Page 172: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/172.jpg)
172
Pre-Fab Review
Commands that request
immediate response
SendToMotorDriver
Position Command
motorPos
WaitFor(1 motor)
Message structure
Interrupt Service Routine
VME board
Sent Ring Buffer
Out Ring Buffer
response
commands
commands
commands/status
status (Fetched)
SemDone(one per motor)responses
(char by char)
commands
semResponse
Per Motor
Controller for 4 Motors
Four Motors
Ok or Timeout
semaphorecommand/response
![Page 173: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/173.jpg)
173
Pre-Fab Review
This page intentionally left blank
![Page 174: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/174.jpg)
174
Pre-Fab Review
Motor Motion
![Page 175: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/175.jpg)
175
Pre-Fab Review
This page intentionally left blank
![Page 176: GNIRS PRE-FABRICATION REVIEW · Risk Reduction overview 1045 Bench Design - Detail description Gary - Analysis Ed/Gary - Fab issues Gary 1200 Lunch 1300 Mechanism risk reduction Jay](https://reader033.vdocuments.us/reader033/viewer/2022043000/5f76d400a9ffc726f96097b6/html5/thumbnails/176.jpg)
176
Pre-Fab Review
Motion -- up close