INsTRUCTION

1

Thank you for purchasing our reference.

Honda GROM Gear Indicator. Before operating the meter, please read this instruction sheet and keep it for future

1. This meter works on DC12V applications only. 2. For installation, please follow the steps described below. Any damage caused by a wrong installation shall be imputed to the user.3. Do not cut or modify the wire terminal. To avoid shortcircuits, do not pull the wires when installing. 4. Do not disassemble or change any parts.5. Maintenance or repair should be executed by our professionals only. Opening the instrument will void the warranty.6. While riding the vehicle, do not attempt to change the settings in order to avoid injuries.7. This meters only works with digital speed / RPM signal (TTL SIGNAL 0-5V) motorcycles.

Some procedures must be followed to avoid damage to the meter.Some procedures must be followed to avoid any injuries.Some procedures must be followed to avoid damages to your vehicle.

MARK MEANING:

1 Meter X1 2 3

Notice

Accessories

51m

m

37mm 17mm

-10~+60°C (14~140°F)JIS D 0203

●Effective temperature range

●Meter weight●Meter size●Meter standard

Display range: N, 1, 2, 3, 4, 5, 6, 7●Gear meter

~51g

Functions3

●Effective voltage DC 12V

37 X 51 X 17mm

Mid-way connector X5Velcro X1

2 Wiring installation

Honda GROM wiring diagram

Gear Indicator

Please contact your local distributor if the items received are not the same as the ones listed above.

Design and specification are subject to change without notice.

When the speed is too low, the meter might not be able to detect any signal.

Press the button once

Press the button 3seconds

wh002kn01c

Blue / Neutral

Yellow / RPM signal

Green / Speed signal

Red / KEY ONBlack / From Bike

Green, Black / From Bike

Green, Red/ From Bike

Yellow, Green / From Bike

White, Red / From Bike

Black / Ground

●

●

To enter the gear setting mode, press and hold the button behind the meter for3 seconds.Press the button again for 3 seconds in order to enter the pre-shift light setting

(button will become amber) and once more for 3 seconds to set the shift light (button will become red).

pre-shift light setting(shift light will become amber)

shift light setting(shift light will become red)

gear setting

● If the meter can not detect the current gear, the screen will indicate “---” and flash.

Gear learning setting

●Put the meter in pre-shift light setting (see point 4-1).

Pre-shift light setting

To avoid improper gear reading, make sure the motorcycle is on neutral position before entering the gear setting mode.

Setting instructions

Gear & shift light settings

4-1

4-2

●Start the engine and put the motorcycle on neutral position. Press the button for 3 seconds in order to enter the gear setting mode. The will then flash. Press the button briefly to enter the learning mode. The main

STEP 1

●

screen will now switch to 1 and flash.

Put the motorcycle on 1st gear and start riding the motorcycle slowly until the meter detects the 1st gear. Once it has detected the 1st gear, the screen will automatically switch to number 2 and flash.

STEP 2

STEP 5 STEP 6

STEP 3

STEP 4

●Press the meter in shift light setting (see point 4-1). The shift light will now become red to indicate you are in the shift light setting.

Shift light setting

●Once you are in the pre-shift light setting, start the engine and put the motorcycle in neutral position. Increase the RPM of the engine until it reaches half the RPM value you wish to set, then press the button to set the pre-shift light value.

●EX. If you wish to set the pre-shift light at 5000 RPM, rev the engine at half the value (2500 RPM) and push the button to set the value.

● Increase the engine RPM until it reacheshalf the RPM value you wish to set (valueshould be higher than pre-shift value), then, press the button to set the shiftlight value.

●EX. If you wish to set the shift light at 8000 RPM, rev the engine at half the value (4000 RPM) and push the button to set the value.

If no action is taken, the meter will automatically go back to the main screen after 30 seconds.

x 3s x 3s

The shift light will now become amber to indicate you are in the pre-shift light setting.

When the main screen displays thenumber 6 and your motorcycle has only 5 gears, slow down and wait until themeter goes back to the previous gear.Once the gear learning session is done,the meter will go up to the number 8and flash. Learning session is complete.

● Put the motorcycle on 2nd gear and ride the motorcycle until the meter

detects the 2nd gear. Once it has detected the 2nd gear, the screen will automatically switch to number 3 and flash.

●Put the motorcycle on 3rd gear andride the motorcycle until the meter

detects the correct gear. Once the meter has detected the 3rd gear, the screen will automatically switch to number 4 and flash.

●Put the motorcycle on 4th gear andride the motorcycle until the meterdetects the correct gear. Once the meter has detected the 4th gear, the screen will automatically switch to number 5 and flash. And so on untilthe 6th gear.

wh002kn01c

x 3s

x 3s