gallery panels...gallery panels installation packet 3430455100 page 5 of 13 createmid-run blocks...

Gallery PanelsInstallation Instructions

IndexAbound Panel System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 End of Run Gallery Panel - T & L Configuration (HRVCE) . . . . . . . . . . . . . . . . 3 Mid-Run Blocks & Trim (HRVB, HRVxxT, HRVTT) . . . . . . . . . . . . . . . . . . . . . . 5 Mid-Run Gallery Panel (HRVCM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Worksurface Connections (HCTL242, HSTB2W1) . . . . . . . . . . . . . . . . . . . . . . 8Gallery to Gallery Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Glass Installation (HRVGxxxxG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Storage Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Laminate Storage (HRVGLSK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Metal Storage (HRVGMSK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Tackboard Installation (HRVTBxx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Hardware Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Tools Needed:Drill1/4” Hex Drive#2 Philips Bit#3 Philips Bit1/8” Drill Bit1/4” Drill BitCarpenter’s Level

343045510005/12/2020

Gallery Panels Installation Packet

3430455100 of 17

Abound Panel System


3430455100 of 17

CreateEnd of Run Gallery Panel - Single Panel T & L Configuration

Step 2 - Verify bracket is vertical. Attach mounting bracket to gallery panel face using (4) #8 x 7/8” Hex head screws.

Step 1 - With gallery panel lying flat or on side edge, align mounting bracket with pilot holes on bottom of gallery panel. Attach to bottom edge using (2) #8 x 7/8” Hex head screws.

X

X

Note: Gallery panels can be installed before or after Abound panels are connected. HON recommends attaching a single spine panel to each gallery panel before connecting entire spine together. (See examples below...)

Recommended process

If off-modular setup is specified, measure spine location from end of panel.Use center slot to align mounting bracket.

Single-Sided (L) Dual-Sided (T)

Note: Connector kits attach to sets of pilot holes found on the bottom of each gallery panel. End holes are used when installing single-sided (L) applications; middle holes are used for dual-sided (T) applications. Installation of the connector kits is the same for all hole locations.

(G) x2

(G) x4

***IMPORTANT***Wedge Bracket must be installed between

Mounting Bracket and Gallery Panel forproper alignment of Trim & Frameless Glass.


3430455100 of 17

End of Run Gallery Panel - Single Panel T & L Configuration (Continued)

Step 3 - Before attaching gallery panel to spine, the Plastic Leveling Block must be removed and Spacer Brackets must be added to spine panel. All 4-hole pattern connector locations under the height of the gallery panel that do not get covered by the Mounting Bracket require a Spacer Bracket. Individual brackets can be hinged apart by hand and mounted to panel using (2) #10 x 3/4” Hex head screws.

Step 4 - Place spine panel over mounting bracket. Upper flanges of bracket extend into the electrical pass-through slot of spine to align panel heights. Once fully-seated, attach spine panel to gallery panel with #10 x 2 1/4” Flathead wood screws through connector holes of spine frame. Quantity will vary with gallery panel height.

Step 5 - Lift finished assembly onto glides and level. Installation is now complete.

Spacer Bracket

Add Spacer Bracket

Remove Plastic Leveling Block

(A)

(E)

Align bracket into electrical hole of frame.

Do not add Spacer Brackets here


3430455100 of 17

CreateMid-Run Blocks & TrimStep 1 - Align connector blocks with holes of panel frame. Attach

each block to frame with (1) #10 x 3/4” Hex head screw. For best fit, alternate left/right screw location with each block.

Step 3 - Snap trim pieces over connector blocks. Trim aligns to bottom of raceway or panel foot. Trim must be installed to both sides of blocks in all applications.

Connector Block

Step 2 - Repeat for connecting panel.

Step 4 - Remove plastic top cap clips on end of frame: Insert metal alignment clip into top of panel frames. Press top trim into alignment clip.

Fully seat into frames with rubber mallet

(E)

(B) x8

(B) x6


3430455100 of 17

Mid-Run Gallery PanelStep 1 - With gallery panel on edge, align bottom connector bracket with end pilot holes. Attach to bottom edge with (2) #10 x 3/4”

Flathead wood screws.

Note: Top bracket covers slotted standard holes. If setup requires an adjacent overhead storage unit, attach top bracket 15” from gallery panel top edge.

Step 3 - Flip gallery panel onto glides. Attach top connector bracket to inside edge of gallery panel with (6) #10 x 3/4” Flathead wood screws. Align top edge of bracket 1/2” away from the top edge of the gallery panel, as shown.

Step 2 - Finish attaching connector bracket to inside edge of gallery panel with (6) #10 x 3/4” Flathead wood screws. Keep bracket centered for proper alignment.

1/2”

15”

(D) x4


3430455100 of 17

CreateMid-Run Gallery Panel (Continued)Step 4 - Mount gallery panel into slotted standard over mid-run blocks and trim.

Step 5 - Screw top bracket to frame using (4) #8 x 1/2” Wafer head self-drilling screws.

Remove breakaway tabscovering tile lead-in holes.

Bottom finger mounts into second lowest possible position.

Step 6 - Level gallery panel. Installation is now complete.


3430455100 of 17

X X

Worksurface Connections

Note: Worksurfaces can connect to gallery panels with a Cantilever bracket or an L-Tower bracket. Method is dependent on application specified.Step 1 - Install Cantilever(s) into spine at desired height; attach

corresponding worksurface (see Abound Installation Instructions for details).

Cantilever Method

L-Tower Bracket MethodNote: Use of level is required when connecting worksurfaces with L-Tower bracket. Spine and gallery panels must

be level before worksurfaces are installed. All L-Tower bracket applications require additional panel-mounted support to set worksurface height.

Step 1 - With worksurface lying upside down, attach L-Tower bracket and other supports to bottom face. Install L-Tower bracket 3” away from outer edge and flush with gallery panel edge using (3) #8 x 1/2” Hex head wood screws.

Note: Worksurfaces with unsupported spans of 60” or greater require two L-Tower brackets.

Step 2 - Using a 1/4” drill bit, add two holes to Cantilever in approximate locations shown below. If connecting to both faces of a mid-run gallery panel, offset holes to prevent screw interference.

Step 3 - Attach Cantilever to gallery panel using (2) #8 x 7/8” Hex head wood screws. Installation is now complete.

Step 2 - Mount worksurface to panel-mounted bracket. Step 3 - Using level along back edge of worksurface,

adjust support leg glide until surface is flat; attach to gallery panel using (4) #8 x 1/2” Hex head wood screws.

(G) x2

(H) x7

Hole locations


3430455100 of 17

CreateGallery to Gallery Connections - L & T Return Panels

Overview: Gallery Panels may connect to one another with the use of “L” or “T” RETURN panels. Gallery Return panels OVERLAP the edge of a PARENT panel, which may be any standard Gallery Panel or another Return panel. Return panels may be equal or shorter in height to the parent, but not taller.

Installation of Return panels requires template model HRVGTGG (packaged separately).

“L”Left

“L”Right

“T”Symmetric

“T”Nonsymmetric

Note: Gallery Panels may connect in “L” or “T” applications. “L” panels may face left or right, “T” panels may be symmetric or nonsymmetric; below are examples of each. All gallery to gallery variations install in a similar way.

Return Panel Parent Panel

(Standard Gallery Panel)

Return

Parent

TemplateHRVGTGG


3430455100 of 17

Step 1 - Add pilot holes to edge of Parent panel using template HRVGTGG. Place template around edge, pressing upwards against bottom surface to ensure correct vertical alignment of Panels. Using 1/8” drill bit, add pilot holes approximately 1” deep into bottom four holes, and top hole that matches Return panel height.

******IMPORTANT******Do not drill all holes in Template.

Add hole that correlates toReturn Panel height only.

Gallery to Gallery Connections - L & T Return Panels (Continued)

Step 2 - Remove connector bracket from Return Panel to access hardware pack.

Bottom four holes arerequired for all panel types.

ParentPanel

Press template upwardsagainst bottom edge ofParent panel for propervertical alignment.

ReturnPanel

ConnectorBracket

KeyholeBracket

Remove Connectorto access Hardware


3430455100 of 17

Create

(J) x4

(K)

Gallery to Gallery Connections - L & T Return Panels (Continued)

Step 3 - Install shoulder screw into top pilot hole. Screw may need to be loosened or tightened for proper return panel fit-up.

Step 4 - Install Connector Bracket to bottom four pilot holes using (4) #10 x 2 1/4” Flathead wood screws. Connector Bracket aligns Left, Right, or Centered depending on the Return Panel Variation.

Left Panel Right Panel T Panels


3430455100 of 17

(L) x8

Gallery to Gallery Connections - L & T Return Panels (Continued)Step 5 - Mount Keyhole Bracket of Return Panel into place over the shoulder screw by pressing in and down. The

shoulder screw may be loosened or tightened as needed to ensure proper fit-up.

Step 6 - Align Return Panel into place over the bottom Connector Bracket. Secure panel in place using (8) #10 x 1” Flathead wood screws. Screw faces should sit flush or sub-flush to bracket’s face for best Cover fit.

Step 7 - Install Connector Cover(s) into place by sliding sideways into Connector Bracket channels. Covers are packaged separately and may be left uninstalled if storage is mounted flush to panels.

Connector CoverHRVCGGC

“T” Panels receive Covers on both faces

Tap lightly on outeredge with woodblockfor tight fitting covers


3430455100 of 17

CreateStep 1 - Fold flat gasket at relief channels and insert into the slot of the gallery panel with gasket ribs facing outward. Verify that neither end of the gasket is sitting proud of the edge of the gallery panel.

Glass Installation

Laminate Storage Connection (Closed Back Units)Step 1 - Position the unit against the gallery panel and level as needed.Step 2 - Open door if necessary and drill pilot holes in the back of the unit. HON recommends that holes should be positioned

underneath shelves and near the tops of the unit where they will not be as visible. Using the pilot holes as guides, attach the storage unit to the gallery panel using (4) #10 x 1 1/2” Pan head screws.

X X

X X

(F) x4

Hole Locations

Ribs

ReliefChannels

Step 2 - Press the glass panel into the gasket; apply pressure until fully seated. A rubber mallet may be used along the top edge if necessary. Verify glass is level by measuring from the top of the gallery panel on each end.

******IMPORTANT******Gasket can be trimmed withscissors for proper fitup. Cut

to exact channel width tocover internal panel material.


3430455100 of 17

SCALE 0.450

Laminate Storage Connection (Open Back Units)Step 1 - Remove drawers or open the unit if necessary. Attach the L bracket to the inside wall of the storage unit approximately 2”

from the top of the unit using (2) #8 x 1/2” Hex head screws per bracket. Repeat this step on the opposite wall.

Step 2 - Position the storage unit against the gallery panel and level as needed. Attach the storage unit to the gallery panel using (2) #8 x 1/2” Hex head screws per bracket.

SCALE 2.000

2”

SCALE 2.000

(C) x2

(C) x2


3430455100 of 17

CreateMetal Storage ConnectionStep 1 - Position storage unit in appropriate

position against the gallery panel and level as needed.

Step 2 - Open the unit and remove drawers as needed to access the back panel. Drill a minimum of four holes into the wall that will sit flush with the gallery panel. Using a #2 Philips driver, attach the storage unit to the panel using (4)

#8 x 7/8” Hex head wood screws.

SCALE 0.300

X X

X X

(G) x4

Hole Locations


3430455100 of 17

Tackboard InstallationStep 1 - Position the fabric pan in the correct position and verify that it is square to the gallery panel. Attach the pan using (6) #5 -

5/8” flat head screws.

SCALE 0.200

SCALE 0.200

Step 2 - Peel off the backer from all 6 pieces of dual lock to expose the adhesive and set the tackable fabric into the steel pan. Apply pressure to the fabric tile to ensure that the dual lock is adhered to the gallery panel.

SCALE 0.300

SCALE 0.200

X

X


3430455100 of 17

CreateHardware Chart

A#10-12 x 1 1/2” Hex Head0500003400

B#10 x 3/4” Flat Head0500055000

C#8 x 1/2” Hex Head0500057200

E#10 x 3/4” Hex Head0500057900

G#8 x 7/8” Hex Head0500256000

D#8 x 1/2” Self-Drilling Wafer Head3500023100

F#10 x 1 1/2” Pan Head Wood Screw3500084700

H#8 x 1/2” Hex Head0500255000

I#5 x 5/8”Flathead3500005800

J#10 x 2 1/4” Flathead0500240200

K

L

#8 x 1”Shoulder Hex Head0500249500

#10 x 1”Flathead3500005000

gallery panels...gallery panels installation packet 3430455100 page 5 of 13 createmid-run blocks...

Documents