FUJIFILM MEDICAL SYSTEMS USA, INC.

TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARY SUITE

FINAL SITE PLAN

MAY 28, 2017 2017-219-TYP

1 of 12

HQ

FINAL DRAWING PLANS - APPROVALCUSTOMER

DATE

CUSTOMER SIGNATURE

YOUR SIGNATURE APPROVES THIS FINAL DRAWING FOR ACCEPTANCE TO FORWARD TO

YOUR ARCHITECT - CONTRACTOR TO IMPLEMENT INTO THEIR FINAL DRAWING SET

Customer to verify freight size and integrity of any and all elevator(s) used for routing Fujifilm Medical Systems USA equipment.

Fujifilm Medical Systems USA representative.Customer to coordinate routing of Fujifilm Medical Systems USA equipment prior to equipment arrival with local

plans without prior notification.

to design and incorporate our final site plan drawings to your architectural construction documents. Fujifilm Medical Systems USA

It is the customer's responsibility to secure a storage area for equipment on site prior and during installation.

Fujifilm Medical Systems USA reserves the right to make changes to equipment and detailed specification regarding thesepreliminary plans shall not be used for construction documents, please refer to the latter final site plan drawings.

This drawing set is the sole property of Fujifilm Medical Systems USA. It's use is authorized for the customer architect of record

These drawings are provided with the understanding by providing such documents, does not alter any of the terms and conditions

damages resulting (from any matter) from the use of the attached drawings.Also Fuji Medical Systems USA or their agents will not be held liable for any direct, indirect, special, incidental or consequentialFujifilm Medical Systems USA makes no warranty or representation, either express or implied with respect to the attached drawings.

architects, engineers, or other design construction professional in the preparation of official construction documents.requirements. The information contained in this drawing set is provided for the use of customers and their designatedThese drawings are reference drawings (only), illustration of general equipment layout and facility-related equipment

Minimum equipment entry door height 80 INCHES

Minimum equipment entry door width 42 INCHES (recommended)

Passageways and Corridors 60 INCHES

The customer shall supply network drops for IP application.All network outlets will installed and set to 100 base T full duplex and checked prior to equipment install.

Customer to provide an IT representative readily available during the equipment installation period.

All power connections shall be dedicated independent connections to the power distribution panel.

All power shall be guaranteed by the owner to meet the power specificationsnormally associated powering medical electronic equipment.

Please refer to your final site plan drawing for site specific power requirements.

Equipment ambient temperature range 59 - 93 Degrees Fahrenheit.

Relative humidity should be between 45 - 95 percent non-condensing.

The room the equipment is installed within should be kept dust free.

of said sale between Fujifilm Medical Systems USA and their customer.

The customer is responsible for the complete an accurate incorporation of all specifications and requirements from these

siting and placement of purchased Fujifilm Medical Systems USA equipment.These drawing are not to be used as construction documents. It is the sole responsibility of the customer to ensure the correct

reference drawings to your architect of record for use of site preparation. Sufficiency of final site plans and specifications, specifically including

Worldwide Healthcare Designs, Inc. (WHD) is Fujifilm Medical Systems USA sole designer for said project.

All network drops will be installed and marked on the connection prior to installation of the equipment.

It is the customer's responsibility to be in compliance with all local, state and federal safety, electrical, and building

This shall include any and all expenses for room and structural alterations. Site preparation shall be in accordanceIt is the customer's sole responsibility and their expenses for room preparation of said room for this equipment sale.

Any time delay from the removal of the latter may result in an extended installation period.

The customer shall obtain all permits and required licenses needed for Federal, State and Local regulations,

The customer should provide Fujifilm Medical Systems USA a construction time-line chart and also

Power - 3 phase, 480 VACBreaker - 80 amp for 80kW generator

All doors, windows and radiation protection installed and finished.

All electrical conduits, raceway, junction boxes and outlets installed and operational.

flush with ceiling grid and operational.Please have walls painted, baseboards installed, all floors tiled, ceiling tiles installed and light fixtures installed

All plumbing must be installed, finished and operational. Any plumbing connections in the immediate area of

All contractors supplied cables must be pulled and terminated at designated locations.

X-ray Procedure and Control Room - a dust free environment.

and free of lateral or longitudinal interference.All support structures used for install and equipment support must be installed, level (within one-eight inch end to end),

Incoming power to X-Ray room breaker panel connected and operational.

the new installation that is not being used must be capped and covered.

with this set of final site plans and specifications provided by Fujifilm Medical Systems USA.

codes relevant to Fujifilm Medical Systems USA final site plans, equipment and installation.

Radiation protection is not shown on these set of plans, However the customer at their own expense shall obtain a

Also the customer shall bear any expense in complying with any related rules, regulations and ordinances.in connection with the construction. installation and operation of their purchased equipment.

The customer shall advise a Fujifilm Medical Systems USA of any adverse conditions at or near the sitethat could affect the installation scheduling and service support team travel.

but not limited to the accuracy of dimensions (based on information provided), shall be the sole responsibility of the customer.

It is the customer's sole responsibility to properly remove and dispose of any hazardous materials - at their expense.

It is the customer's responsibility to properly remove and make the site conditions safe for installation and operation.

follow-up with scheduled construction meeting notice for project area(room).This is to insure coordination between contractor(s) with delivery and installation of purchased equipment.

All dimensions are measured from finished surfaces, unless otherwise specified on drawing.

We recommend that during equipment delivery and installation, for the customer to protect finished floors, walls andany areas, including other equipment within area of install with protective covering.

Installation will not commence until room is clean and dust free. All contractors equipment must be removed prior to install.Fujifilm Medical Systems USA will not be responsible for any lost, damaged tools and materials from customer's contractors.

licensed radiation physicist to specify need of radiation protection.

Installation will not commence until room is clean and dust free. All contractors equipment must be removed prior to install.Fujifilm Medical Systems USA reserves the right to refuse delivery and installation due to the room is not properly preparedper accordance with Fujifilm Medical Systems USA final site plans.

The customer or contractor shall supply and install all materials and other features called-out from Fujifilm Medical Systems USA final site plans.

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

NOT TO SCALE

2017-219-TYP

2 of 12

CUSTOMER-CONTRACTOR TO PROVIDE VACUUM AND OXYGEN OUTLETS PER THEIR

CUSTOMER-CONTRACTOR TO PROVIDE DESK, CHAIR, AND CABINETRY PER THEIR NEEDS.

CUSTOMER 'S PHYSICIST TO DETERMINE AREA SHIELDING REQUIREMENTS.

BY THE CUSTOMER. CONTROL ROOM MAXIMUM WALL HEIGHT NEEDS TO BE 7 '-6 ' '.LEAD LINED WINDOWS-WALLS, CABINETRY, COUNTER AND SINKS ARE TO BE PROVIDED

PLEASE VERIFY ROOM DIMENSIONS TO THE ACTUAL SITE CONDITIONS.

2.

6.

5.

4.

3.

1.

( IF APPLICABLE )

REQUIREMENTS.

NEW WALLS

EXISTING WALLS

EXISTING WALLS TO BE REMOVED

CUSTOMER TO SUPPLY ALL CONSTRUCTION

13 '-0 ' ' STANDARD RAILS SHOWN

PLAN NORTH

N

EQUIPMENT PLAN

*

SUPPLIED-INSTALLED BY MEDICAL MANUFACTURERSUPPLIED-INSTALLED BY CUSTOMER-CONTRACTOR

12

008

CODE ITEM

EQUIPMENT LEGEND

W ' ' D ' ' H ' ' WT. LBS BTU HR

SA-60 (HIGH SPEED ROTOR CONTROL)

009

010

CONTROL CONSOLE

FUJIFILM FDX CONSOLE,

BAR CODE READER, MOUSE,KEYBOARD, COMPUTER,

FUJIFILM VISIONARY GENERATOR

OVERHEAD TUBE CONTROL CABINET

FUJIFILM VISIONARY CHEST STAND

FUJIFILM VISIONARY CEILING MOUNT

FUJIFILM 19 ' ' TOUCH MONITOR007

002

FUJIFILM VISIONARY X-RAY

X-RAY TUBE

003

004

005

006

001

113522 LBS.18 ' '10 ' '17 ' '

353 LBS.

529 LBS.

4 LBS.

N A

485 LBS.130 ' '

27.5 ' '

12 ' '

BRIDGE

28.5 ' '

157.5 ' ' VARIBLERAILS

16 ' '

13.5 ' ' 3 ' '

85 ' '

31 ' ' 87 ' '

1XXXX

XXXX 1

1

1

XXXX 1

FUJIFILM VISIONARY TABLE

011 4.7 ' ' 13.8 ' ' 13.8 ' ' 17 LBS. 1

CONTROL BOX - TABLE 20 ' ' 1

N AN AN AN A

N A

N A16 ' ' 17 ' ' 110 LBS.

TILT

(CH-BOTTOM BOX) STACKED

(BK-TOP BOX) STACKED

20.5 ' ' 1N A18.5 ' ' 15 ' ' 110 LBS.

20 ' ' 1N A16 ' ' 17 ' ' 110 LBS.

37.5 ' ' 1N A92.5 ' ' 36 ' ' 700 LBS.(TABLE WEIGHT LIMITATION 650 LBS)

DR-ID 600PU-MP NEAR GENERATOR

MC COMPUTER, PPU-OPTION

N A

SEE NOTE 3

PLEASE FIELD VERIFYALL EXISTING INTERNALWALL DIMENSIONS, DOORLOCATIONS, ETC...

PLEASE FIELD VERIFYALL EXISTING INTERNALWALL DIMENSIONS, DOORLOCATIONS, ETC...

SEENOTE 2

CONTROLAREA

RADROOM 2

3 ' - 6 ' 'EXISTING

DOOR

EXISTINGSINK, COUNTERAND CABINET

EXISTING CEILINGSUPPORT - QTY. (6)(FIELD VERIFY LOCATION)

EXISTING J-BOXESQTY. (2)(FIELD VERIFY LOCATION)

EXISTING WALLDUCT(FIELD VERIFY LOCATION)

012 D-EVO GL MOBILE 19 ' ' 1N A17 ' ' 57 ' ' 66 LBS.CASSETTE STAND

SEE NOTE 3

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

1/4"=1'-0

2017-219-TYP

3 of 12

ROOM WALL

24.68～

84.53

MATCH HOLE WITH BASE13.98～35.63

24.68～84.53

MATCH HOLE WITH BASE

353 LBS265 LBS 529 LBS

700 LBS

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A

MAY 28, 2017

NOT TO SCALE

2017-219-TYP

4 of 12

ONCE THE DOOR IS OPENED. CUSTOMER TO DETERMINEREQUIREMENT AND LOCATION BASED ON LOCAL CODES.

GENERATOR HAS NORMALLY OPEN CONTACT

RUN POWER AND RETURN FOR WARNING LIGHT TO

DOORSWITCH FOR EACH DOOR HINGENOTE IF DOUBLE DOORS ARE APPLIED, USE ONE

SEE TROUGH LAYOUT FOR LOCATION OFWARNING LIGHT DOORSWITCH LOCATIONS

WARNING LIGHT 4 ' ' (10cm) STANDARD BOX WITH X-RAY ONOR RED WARNING LAMP OVER DOOR. USE INCANDESCENT

OPTIONAL DOORSWITCH INTERRUPT MICROSWITCH IN JAMB,SQUARE D, TYPE AO, NORMALLY OPEN, 24-120 VOLTS.

TO PREVENT AN X-RAY EXPOSURE FROM OCCURRING

TO ENABLE WARNING LIGHT.

X-RAY GENERATOR.

FIXTURES ONLY.

ROOMWALL

TELESCOPETUBE

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

1/4"=1'-0

2017-219-TYP

5 of 12

NOTESELECTRICAL

CHEST

( POWER AND CONDUIT DUCT SUPPLIED AND INSTALLED BY CUSTOMER 'S CONTRACTOR )

CONTROL ROOM

INSTALLATIONCABLE DIAGRAM

80 AMP BREAKER3 PHASE, 480VAC

GENERATOR

SIZE PER CODE

FOR 80kW

AC POWER

CB1

STAND

TABLE

MOUNTSYSTEM

CEILING

CB2

208VPOWER

CB3

208VPOWER

20 AMP BREAKER 20 AMP BREAKER

CB4

208VPOWER

30 AMP BREAKER

SA-60 (HIGH SPEED ROTOR CONTROL)

CONTROL BOX - TABLE(BK-TOP BOX)

OVERHEAD TUBE CONTROL CABINET(CH-BOTTOM BOX)

(FROM OPENING INX-RAY ROOM)

TABLE CONTROL BOX(BK-TOP BOX)

OVERHEAD TUBE

(CH-BOTTOM BOX)CONTROL CABINET

HIGH SPEEDROTOR CONTROL(SA - 60)

CONTROL CONSOLEVISIONARY

GENERATOR SPECIFICATIONS

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

1/4"=1'-0

2017-219-TYP

6 of 12

PLAN NORTH

NELECTRICAL PLANS

FIELD VERIFYFIELD VERIFY

LTABLE CFIELD VERIFY

FIELD VERIFY

LT

AB

LE C

FIE

LD

VE

RIF

Y

FIELD VERIFY

FIE

LD

VE

RIF

YF

IEL

D V

ER

IFY

FIE

LD

VE

RIF

Y

CONTROLAREA

RADROOM 2

EXISTING J-BOXESQTY. (2)(FIELD VERIFY LOCATION)

EXISTING WALLDUCT(FIELD VERIFY LOCATION)

FIE

LD

VE

RIF

Y

FIE

LD

VE

RIF

Y

FIELD VERIFY

FIELD VERIFY

FIELD VERIFY

FIELD VERIFY

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

1/4"=1'-0

2017-219-TYP

7 of 12

ELECTRICAL ISOMETRIC

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

1/4"=1'-0

2017-219-TYP

8 of 12

POWER WIRES FROM FUJI MEDICALSIGNAL CABLES. (SEE RACEWAY LAYOUT, DIAGRAM).

ALL TROUGH SHALL BE SQUARE-D, WALKER DUCT (OR EQUAL) FLOOR AND WALL TRENCH DUCT.SIZES SHALL BE AS SPECIFIED ON DRAWINGS, OR PROVIDE EQUIVALENT NOMINAL SIZES AVAILABLEFROM MANUFACTURER (SEE TROUGH LAYOUT, DIAGRAM). FLOOR TROUGH TO BE GASKETED TO

ALL TROUGH SHALL BE FLUSH WITH FINISHED SURFACES UNLESS OTHERWISE SPECIFIED AND PROVIDED WITH REMOVABLE COVERS THE LENGTH. COVERS SHALL BE CLEAR OF ANYOBSTUCTION FOR INSERTION OF PRE-PLUGGED CABLES. IF IT IS NECESSARY THAT THE TROUGHBE SURFACE MOUNTED, WHEN NOT INDICATED ON THESE FUJIFILM MEDICAL DRAWINGS, ALL EQUIPMENT

PLACEMENT AND TRAVEL CLEARANCE MUST BE VERIFIED TO PREVENT EQUIPMENT AND TROUGHINTERFERENCE AND POSSIBLE EQUIPMENT DAMAGE. CONTACT FUJIFILM MEDICAL PROFESSIONAL DESIGNSERVICES FOR PROPER VERIFICATION OF EQUIPMENT PLACEMENT AND TROUGH CLEARANCES.

REMOVABLE TYPE BARRIER STRIP AND CROSSOVERS MAY BE REQUIRED FOR SEPARATION OF A.C.POWER WIRES OR VIDEO COAX CABLES FROM FUJIFILM MEDICAL SIGNAL CABLES. (SEE TROUGH LAYOUT,

PAINT ALL EXPOSED AREAS OF TROUGH. CONSULT WITH CUSTOMER ON MATCHING OR ACCENT COLORS.

WHEN ORDERING TROUGH DUCT AND REQUIRED FITTINGS FROM SQUARE-D OR WALKER PAKERSBURG,USE THE APPROPRIATE CATALOG NUMBERS FOR EACH ITEM TO EXPEDITE DELIVERY.

"SWEEP ELBOWS" FOR CORNER BENDS SHALL BE PROVIDED. THE FOLLOWING SQUARE-D CATALOGNUMBERS (OR EQUAL): "RWT-SFEE" FOR FLUSH MOUNTED TROUGH. "RWT-SSEES" FOR SURFACEMOUNTED TROUGH. NOTE: WHEN ORDERING, SPECIFY 10" OR 18" TROUGH USAGE.

ALL RACEWAY SHALL BE SURFACE MOUNTED ON FINISHED SURFACES UNLESS OTHERWISE SPECIFIEDAND SHALL BE PROVIDED WITH REMOVABLE COVERS, THE FULL LENGTH. COVERS SHALL BE CLEAROF ANY OBSTRUCTION FOR INSERTION OF PRE-PLUGGED CABLES.

PAINT ALL EXPOSED AREAS OF RACEWAY. CONSULT WITH CUSTOMER ON MATCHING OR ACCENT

ALL RACEWAY SHALL BE "WIREMOLD" BRAND (OR EQUAL) FOR FLOOR, WALLS, OR CEILING, UNLESSOTHERWISE SPECIFIED. (SEE RACEWAY LAYOUT, DIAGRAM FOR RECOMMENDED SIZES).

REMOVABLE TYPE BARRIER STRIP AND CROSSOVERS MAY BE REQUIRED FOR SEPARATION OF A.C.

DIAGRAM)

COLORS.

PREVENT ENTRY OF LIQUIDS.

NOT TO SCALE

THIS DETAIL IS A RECOMMENDATION ONLY. CONTRACTOR TO DETERMINE

THIS DETAIL APPLIES TO JUNCTION BOXES INDICATED ON FUJIFILM MEDICAL'S FINAL

OPEINGS OF THESE BOXES SHALL FEATURE EXPOSED REMOVEABLE COVER

ACTUAL METHODS BASED ON SPECIFIC SITE CONDITIONS.

DRAWINGS WITH LETTER DESIGNATIONS JB1, JB2, ETC.

PLATES AS DESIGNATED.

WITH 2 DIVIDERS FOR

GROMMETTED OPENING FOR

VERTICAL RACEWAY RISER FORTUBERCRANE CABLES.

JUNCTION BOX AND CONDUITWITHIN WALL

TROUGH TUB TO MATCH JUNTION BOXOPENING THROUGH REAR OF RACEWAY/

SURFACE RACEWAY / TROUGH TUB

OPENING

GROMMET SHARP EDGES

COVER PLATE CUTAWAY VIEW

COVER PLATE

WALL LINE

CABLE SEPARATIONS.

CABLE ACCESS.

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

1/4"=1'-0

2017-219-TYP

9 of 12

STRUCTURAL PLAN

OR SUPPLY AN ACCESS THROUGH CEILING TO SERVICE EQUIPMENT.PLEASE SUPPLY A SUSPENDED FINISHED CEILING. PREFERED FOR SERVICING TUBE SUSPENSION.

BOLTS, ANCHORS, PULL-TESTING, WATER PROOFING MATERIAL, ETC.

CHEST STAND SYSTEM BASE, SURFACE MOUNTED WITH THE FINISHED FLOOR. INSTALLED BY FUJIFILM 'SINSTALLATION TEAM. STRUCTURAL CONTRACTOR TO PROVIDE ANY ADDITIONAL MATERIALS,

STRUCTURAL CONTRACTOR MUST COORDINATE WITH THE CUSTOMER'S ARCH. OF RECORD

STRUCTURAL LEGEND

TO ENSURE NO PROTRUSIONS AT ALL EXIST FROM BELOW THE FINISHED CLG. THE ENTIRELENGTH OF TRAVEL FOR THE SIEMEN 'S BRIDGE. ANY AND ALL EQUIPMENT MUST BE OF THERECESSED TYPE. ANY DEVIATION MUST BE BROUGHT TO THE ATTENTION OF THE LOCALFUJIFILM SERVICE REP.

FUJIFILM 'S CEILING SYSTEMS RAILS (SEE DETAIL SHEET).

CODE DESCRIPTION

BOLTS, ANCHORS, PULL-TESTING, WATER PROOFING MATERIAL, ETC.INSTALLATION TEAM. STRUCTURAL CONTRACTOR TO PROVIDE ANY ADDITIONAL MATERIALS, TABLE BASE, SURFACE MOUNTED WITH THE FINISHED FLOOR. INSTALLED BY FUJIFILM 'S

TYPICAL UNISTRUT P-1001K OR P-5501K, OR EQUAL, FLUSH MOUNTED WITH FINISHEDCEILING. PAINT TO MATCH FINISHED CEILING. BOLT SPACING OF EQUIPMENT SHALL DETERMINETYPE OF UNISTRUT TO BE USED. VERIFY WITH LOCAL FUJIFILM MEDICAL REPRESENTATIVE.

(CUSTOMER TO DETERMINE IF EXISTING STRUCTURE CAN SUPPORT NEW SUPPORT RAILS AND(SUPPLIED AND INSTALLED BY THE CUSTOMER 'S CONTRACTOR).

CEILING MOUNT SYSTEM).

PLAN NORTH

N

FIE

LD

VE

RIF

Y

LTABLE C

CH

EST

ST

AN

D CL

SEE DETAILSFIELD VERIFY

SEE

DE

TA

ILS

FIE

LD

VE

RIF

Y

LT

AB

LE C

SEE

DE

TA

ILS

FIE

LD

VE

RIF

Y

FIELD VERIFY

CONTROLAREA

EXISTING CEILINGSUPPORT - QTY. (6)(FIELD VERIFY LOCATION)

FIELD VERIFY

RADROOM 2

FIE

LD

VE

RIF

Y

FIELD VERIFY

EXISTING

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

1/4"=1'-0

2017-219-TYP

10 of 12

CUSTOMERS RESPONSIBILITY TO HAVE A RADIATION SURVEY PERFORMED IF NEEDED.RADIATION SHIELDING IS NOT SHOWN ON THE SET OF PLANS, HOWEVER IT IS THE

THE CUSTOMER OR HIS CONTRACTORS SHALL SUPPLY AND INSTALL MATERIALS AND OTHER THE CUSTOMER IS RESPONSIBLE FOR ALL UTILITY TIES CONNECTIONS AND SERVICES.

THE CUSTOMER IS RESPONSIBLE FOR ALL ROOM PREPARATION COSTS, FEES, PERMITS AND

BEAR SOLE RESPONSIBILITY FOR COMPLIANCE WITH APPLICABLE CODES ( NEC, OSHA, LOCAL, THE OPERATION OF THE EQUIPMENT. THE CUSTOMERS ARCHITECT OR ITS AGENT SHALL ATTACHED RECOMMENDED LAYOUT, CONFIGURES THE LAYOUT PLAN TO ALLOW OPTIMUM OF EVERY EFFORT HAS BEEN MADE TO ASSURE THAT THE EQUIPMENT DEPICTED ON THE

SYSTEMS U.S.A., INC WILL NOT BE RESPONSIBLE FOR DESIGNS AND CONSTRUCTION THAT DO THE ELECTRICAL AND STRUCTURAL REQUIREMENTS FOR THAT EQUIPMENT. FUJIFILM MEDICAL THESE DRAWING SUGGEST PLACEMENT OF THE PURCHASED EQUIPMENT, AS WELL DESCRIBE

ARCHITECT OF RECORD OR AGENT SHALL PREPARE CONSTRUCTION DOCUMENTS.THE ATTACHED DRAWINGS ARE NOT FOR CONSTRUCTION PURPOSES. THE CUSTOMERS

CONSTRUTION.

BRACE UNISTRUT OR POWER STRUT ATTACHED TO VERTICAL COLUMNS AS SHOWN ON DETAIL.

CORPORATION. ALL STRUT MEMBERS SHALL BE SUPPLIED AND INSTALLED BY

LOCATION OF VERTICAL COLUMNS SHALL VARY DEPENDING ON BUILDING

STRUT CHANNEL SUPPORT SHOULD BE A PART OF SPECIALTIES SPECIFICATIONS,

SPANNING MEMBER 'S UNISTRUT OR POWER STRUT FLUSH WITH FINISHED

VERTICAL COLUMNS: UNISTRUT OR POWER STRUT ATTACHED TO SPANNINGMEMBERS AS SHOWN ON GENERAL CEILING DETAILS SHEET. NUMBER AND

RECOMMENDED UNIVERSAL STRUT CHANNEL SUPPORT FRAMEALLOWS FOR TRANSVERSE AND LONGITUDINAL ADJUSTMENT AT TIME OF EQUIPMENTINSTALLATION. DETERMINATION OF THE ACTUAL DESIGN SHALL BE COORDINATEDAND APPROVED BETWEEN ENGINEER OF RECORD AND UNISTRUT OR POWER STRUT

CEILING. SPACED 2 '-2 ' ' O.C.

OMITTED

SEC. 10. NOT IRON SPECIFICATIONS.

CONTRACTOR.

O.C. TYPICAL

3

78 ' '

FEATURES CALLED OUT IN THE PLANS.

INSPECTIONS.

NATIONAL, RADIATION SAFETY ).

NOT FOLLOW THOSE GUIDELINES.

1

4

LARGE A STANDARD 30-INCH COUNTER TOP MAY NOT BE SUFFICIENT.COMPUTERS INCLUDING KEYBOARD DRAWS. SINCE SOME OF THE CRT MONITORS ARE VERY THE RESPONSIBILITY OF THE CUSTOMER TO PROVIDE ERGONOMIC DEVICES TO HOLD THESE IN AREAS THAT HAVE IIP'S PRINT SERVERS, QA 771WS OR SIMILAR DEVICES LOCATED, IT IS

MUST BE CAPPED OR COVERED PRIOR TO INSTALLATION OF THE FUJIFILM MEDICAL SYSTEMS EXISTING SERVICES THAT WILL NOT BE USED ( I.E. PULMBING, J BOXES, FLOOR DRAINS )

CABLES AND TERMINATIONS. THIS WORK SHALL BE PRIOR TO INSTALLATION START.THE CUSTOMER IS RESPONSIBLE FOR THE SUPPLY AND INSTALLATION OF ALL INTERCONNECT

WORK WHICH SHALL BE COMPLETED AFTER THE INSTALLATION OF THE PURCHASED SYSTEM.THE CUSTOMER OR HIS CONTRACTOR IS RESPONSIBLE FOR ANY FINAL PAINT OR TOUCH-UP

EQUIPMENT.

BRACE

REQUIRED FITTING

REQUIRED FITTING

VERTICAL COLUMN

FUJIFILM MEDICAL LONGITUDINALCEILING TRACK

SPANNING MEMBER

REQUIRED FITTING

FINISHED CEILING LINE

REFERENCE TO 2 '-2 ' ' IS SHOWNFOR 2 ' x 4 ' CEILING TILES ONLY.SPACE BETWEEN SUPPORT RAILSCAN VARY BETWEEN 34.5 ' ' TO 53.125 ' '(BASED ON INSTALL MANUAL)

DRAWINGS TO MATCH FUJIFILM MEDICALLONGITUDINAL CEILING TRACK SPACINGS.RAILS SUPPLIED AND INSTALLED

SPECIFIED ON SITE PLANNINGO.C. OR AS OTHERWISE

BY FUJIFILM MEDICAL INSTALLATIONS.

NOT TO SCALE

DETAILSSEE GENERAL

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

1/4"=1'-0

2017-219-TYP

11 of 12

.25 ' ' ( 6.4MM ) MINIMUM THICK WASHER OR ELONGATED WASHER PLATES MUST BE PLACED AT

STRUT CHANNEL LONGITUDINAL TRACK SUPPORT SHALL BE FASTENED TO STRUT CHANNEL SPANNINGMEMBER BY USE OF APPROPRIATE HARDWARE MANUFACTURED BY UNISTRUT OR POWER STRUT.

CHANNEL LOCATED BETWEEN FINISHED CEILING LINE AND TOP OF FUJIFILM MEDICAL LONGITUDINAL CLG. TRACK.EXPOSED STRUT CHANNEL LONGITUDINAL TRACK SUPPORT SHALL BE 1.625 ' ' DEEP SLOTTED

NOT TO SCALE

SLOTTED HOLES FOR THIS CONNECTION.

FUJIFILM MEDICAL STRONGLY RECOMMENDS THAT THE CUSTOMER HIRE A STRUCTURAL ENGINEER(ENGINEER OF RECORD) WHO IS REGISTERED AND CERTIFIED IN THE STATE IN WHICH THE CUSTOMER'S SITE IS LOCATED. THE ENGINEER OF RECORD SHALL BE RESPONSIBLE FOR PROVIDING AND APPROVING A DESIGN FOR ADAPTING THE SUPPORT STRUCTURE TO THE NEW OR EXISTING BUILDING STRUCTURE. THE CEILING SUPPORTSTRUCTURE INCORPORATING THE DESIGN OF THE ENGINEER OF RECORD SHALL BE SUP-PLIED AND INSTALLED BY CONTRACTOR, AS PART OF THE IRON WORK OR SPECIALTIES

A WELDED OR FABRICATED STRUCTURAL SUPPORT IS REQUIRED FOR CEILING MOUNTED X-RAY UNITS. ITS TOP MEMBER IS FASTENED TO THE FLOOR SLAB ( OR BUILDING STEEL ) ABOVE THE X-RAY ROOM. THE BOTTOM OF ITS LOWEST SPANNING MEMBER IS FLUSH WITH THE FINISHED CEILING TO WHICH THE STATIONARY CEILING TRACKS ARE FASTENED WITH MOUNTING HARDWARE SUPPLIED AND INSTALLED BY FUJIFILM MEDICAL.

THE FOLLOWING GENERAL DETAILS INDICATE A BASIC SUPPORT METHOD THAT PERMITS TRANSVERSE AND LOGITUDINAL ADJUSTMENT OF BOLT CENTERS AT THE INSTALLATION SITE. IT CAN BE ADAPTED TO ACCOMMODATE THE VARIOUS ARCHITECTRAL CIRCUMSTANCES

THE SUPPORT MUST BE RIGID, SECURELY BRACED AND LEVEL IN BOTH DIRECTIONS AT THE FINISHED CEILING LINE. LENGTH AND LOADING CAPACITY WILL DEPEND ON THE SELECTED CEILING UNIT AND NUMBER OF CARRIAGE ASSEMBLIES TO BE BORNE. ACTUALEQUIPMENT LOADS FOR EACH ROOM ARE SPECIFIED ON THE FUJIFILM MEDICAL SITE PLANNING DRAWINGS UNDER THE STRUCTURAL DETAIL SPECIFICATIONS.

FUJIFILM MEDICAL SUGGESTS THROUGH BOLTING THE SUPPORT STRUCTURE TO BUILDING STRUCTURE WHENEVER POSSIBLE. FUJIFILM MEDICAL WILL ALSO ACCEPT THE APPLICATION OF HILTI EXPANSIONANCHORS ( OR EQUAL ) IN LIEU OF THROUGH BOLTING. ACTUAL METHODS AND MATERIALS

SHALL BE DETERMINED BY ENGINEER OF RECORD. ALL SUPPORT MEMBERS, ANCHOR BOLTS,AND HARDWARE SHALL BE SUPPLIED AND INSTALLED BY CONTRACTOR. THE LENGTH OF BOLTSSHALL BE DETERMINED TO MEET SPECIFIC SITE REQUIREMENTS BY ENGINEER OF RECORD.

FUJIFILM MEDICAL WILL ACCEPT THE USE OF UNISTRUT OR POWER STRUT SUPPORT MEMBERS FOR CONSTRUCTION, ONLY IF SUPPORT STRUCTURE IS DESIGNED AND CERTIFIED BY UNISTRUT OR POWER STRUT CORPORATION, IN CONJUNCTION WITH THEENGINEER OF RECORD. THESE STRUT CHANNEL MEMBERS MUST NOT BE WELDED TOGETHER.THE APPROPRIATE AVAILABLE HARDWARE SHALL BE APPLIED.

CENTERLINES OF THE TWO STRUCTURAL MEMBERS HOLDING THE SUSPENDED WEIGHTS ARESHOWN. UNISTRUT OR POWER STRUT FLUSH FINISHED CEILING SHALL BE IDENTIFIED AS THE SPANNING MEMBERS. THESE MEMBERS MUST BE LEVEL IN BOTH DIRECTIONS TO WITHIN1 16 ' ' ( 1.6MM ) AND BRACED TO PREVENT MOVEMENT IN ANY DIRECTION. THEY MUST BESECURED TO THE SLAB ABOVE AND/OR TO THE BUILDING STRUCTURE TO THE HOLD THE DEAD

INSTALLATION OF THE SUPPORT MAY BE AFFECTED BY OTHER ARCHITECTURAL OR MECHANICAL PROVISIONS WHICH MAY BE LOCATED IN THE SAME AREA. IN THIS CASE, COORDINATION OF THE REPRESENTATIVE MUST BE CONSULTED BEFORE ANY DEVIATION FROM THE SITE PLANNING

WEIGHTS INDICATED.

DRAWINGS IS UNDERTAKEN.

CONTRACT.

ENCOUNTERED AT EACH INSTALLATION.

- CUSTOMER IS RESPONSIBLE FOR MEETING SITE CONDITIONS FOR STATIC LOADS,

( WIDTH, DEPTH, STRENGTH, ETC...)- SUPPORT STRUCTURE MUST MEET ALL REQUIRED EQUIPMENT SUPPORT NEEDS.IS CERTIFIED BY A LICENSED/PROFESSIONAL STRUCTURAL ENGINEER.CUSTOMER CAN ALSO UTILIZE AN EXISTING SUPPORT STRUCTURE, ONLY IF THE STRUCTURE

FINISHED CEILING LINE

SPANNING MEMBER SUPPLIEDAND INSTALLED BY CONTRACTOR

FUJIFILM MEDICAL LONGITUDINALCEILING TRACKMOUNTING SURFACE OF

FUJIFILM MEDICAL LONGITUDINALCEILING TRACK

BOTTOM OF SPANNING MEMBERFLUSH WITH FINISHED CEILING LINE

EACH MEMBER 2 '-2 ' 'O.C.

LEVELNESS, ETC...)

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSVISIONARY EQUIPMENT PLANS

STAMFORD, CT 06801

VISIONARYSUITE

WHD-A.A.

MAY 28, 2017

1/4"=1'-0

2017-219-TYP

12 of 12