for your inventer ventilation system · 2019. 5. 22. · 1 2. information for your inventer...

www.inventer.eu

Informationfor your inVENTer® ventilation system

2 Information for your inVENTer ventilation system

Air is indispensable!

People can live for weeks without food, days without liquid, but only a few minutes without air.

With our ventilation system you get a healthy and comfortable climate in your living space and thus you ensure the value of your property as well as the health of the residents.

You have purchased a ventilation system that gives high room humidi-ty and mould formation no chance! Cleaning the fans and the ceramic accumulator as well as replacing the filters is very easy. In addition, you save valuable energy through the high degree of heat recovery and make an active contribution to environmental protection.

You or other residents are allergic? Then from now on you can relax and breathe deeply at home

Do you have any questions?

We or your local factory representative are only a phonecall away!

Annett Wettig (Managing Director) and the entire inVENTer team thank you for your confidence and wish you pleasure with healthy, fresh indoor air.

Annett WettigManaging director

Dear inVENTer costumer,

3Information for your inVENTer ventilation system

Overview

Chapter I This is how your inVENTer ventilation unit works:

Ventilation with heat recovery! 5

Chapter II Overview of the most important functions of your

inVENTer controller 9

Chapter III Overview of the most important functions of your

inVENTer inner covers 25

Chapter IV How to clean your

inVENTer ventilation units 31


Chapter I

This is how your inVENTer ventilation unit works:Ventilation with heat recovery!


This is how inVENTer works: Ventilation with heat recovery!

Construction

Inner cover with filter:The closeable inner cover optically closes your ventilation unit off from the inside. The integrated filter ensu-res that neither pollen nor dust can penetrate from the outside.

Ceramic heat accumulator:The honeycomb-shaped ceramic core stores the heat of the outflowing room air. When the fan has changed its di-rection of rotation, it warms up the incoming fresh air befo-re it enters the interior.

inVENTron®:Reversible fan Xenion®

and double air control unit:Xenion® ensures optimum air ex-change: it changes the direction of rotation every 70 seconds. It is em-bedded in two air control units that ensure uniform and efficient flow through the entire ceramic heat ac-cumulator.

The inVENTer ventilation system consists of ventilation units arranged in pairs, which always work in push-pull.

1 The fan of a ventilation unit rotates in one direction for 70 seconds and transports the used air outside. The cera-mic heat accumulator stores the heat of the air from the interior. The direction of rotation then changes.

2 Now the fresh air flows from the outside into the interior. In the process, the ceramic releases the stored heat back into the fresh air. A large part of the heat is thus returned to the interior with the incoming air.

In this way inVENTer ensures an optimalfeel-good atmosphere in your home.

How it works

Exterior closure:In the outdoor area, a driving rain-proof closure conceals the compo-nents of your ventilation unit. So no water can penetrate from the out-side. Integrated insulation reliably reduces external noise. With some product variants, the outer edge is integrated inconspicuously into the window reveal.

Wall sleeve:The wall sleeve is located in the ou-ter wall. All basic components of the ventilation unit are inserted into this sleeve. Depending on require-ments, additional components for sound insulation or wind protection accessories can be located in the wall sleeve.

1

2


Operation Your ventilation unit is controlled via the sMove basic controller or the MZ-Home premium controller. With the help of the controllers you can determine the type of operation and the output level in which your ventila-tion unit should operate. Depending on the controller, further functions are possible, such as setting a weekly timer.The range of functions can be further extended by sensor technology (de-mand-driven ventilation).

First steps Your ventilation unit has various output levels. They can be set alternatively in the main operating modes "heat recovery" and "continuous ventilation". Switching to the corresponding operating mode and output level is either automatic via sensors or manual.All ventilation units can be set to a pause function and/or switched off completely.

The inner cover can optionally be opened, closed or in some cases tilted. By tilting the inner cover you can influence the direction and intensity of the air volume flow as well as the sound volume of the ventilation unit.

When to choose which operating mode?

Heat recovery function: In this operating mode, the reversible fans of the ventilation units operated in pairs change the direction of rotation, resulting in alternating charging and discharging of the heat accumula-tor.

Select "Heat recovery" as the standard operating mode. During the heating periods, the outdoor temperature is colder than the indoor air temperature. The incoming air is preheated as it flows through the ceramic heat accumulator before entering the interior. It is also re-commended on summer days. The higher outside temperature compa-red to the interior significantly reduces the heat input during ventilation.

Continuous ventilation function: In this operating mode, the reversi-ble fans do not change the direction of rotation. This means that there is no heat recovery.

Select "Continuous ventilation" to cool the room in summer nights or to quickly remove used or humid room air.

Pause function: In this operating mode, the reversible fans are tem-porarily switched off. The ventilation units do not work and there is no air exchange. After the temporary pause, the fans restart automatically. Therefore, leave the inner cover open.

Select "Pause" if your ventilation unit is to be switched off temporarily, for example before going to bed.

Off function: In this operating mode, the reversible fans are switched off. The ventilation units do not work and there is no air exchange. Close the inner cover in this state.

Select "Off" if your ventilation unit is to be switched off for a longer peri-od of time, e.g. for cleaning the fans or when the inner cover is closed.



When must the inner cover be opened or closed?

Open inner cover: While the ventilation unit is in operation, the inner cover must always be open. If the "Pause function" is selected, the inner cover must be open.

Closed inner cover: Close the inner cover when the fan is switched off for a longer period of time to avoid undesired cooling of the room. If you have selected the "Off" operating mode, the inner cover must be closed.

In situations in which you are asked to close windows and doors, your ventilation unit must also be switched off and the inner cover closed.

Re-open the inner cover again as soon as you put the ventilation unit back into operation.

When can the output level be changed?

The inVENTer controllers have different power levels for the operation of the ventilation units. On average, all power levels can be used.

Increase the output level to achieve stronger ventilation. This may be necessary if there are more people in the room than usual, e.g. during celebrations, or if there is increased moisture ingress, e.g. by hanging up laundry.

Reduce the power level if there are fewer people in the room than usu-al, for example during holiday periods.Note, however, that this reduces air exchange.



Chapter II

Overview of the most important functions of yourinVENTer controllers


The sMove s4 and sMove s8 controllers are electronic control units for controlling the inVENTer ventilation systems. They are operated by tou-ching the capacitive keys and the slider on the control panel. With its in-tegrated illuminated displays, the control panel also serves as a display surface.

The controller sMove has the possibility to pause your ventilation units between one and eight hours. During this time, the remaining break hours can be viewed.A 15-minute boost function is available to quickly remove used air.

A filter change indicator automatically reminds you of the necessary filter change of your ventilation unit.

General information

Description

Control panel

The sMove s4 controller controls up to four iV-Smart+ or iV14-Zero ven-tilation units, or two iV-Twin+ or iV25 ventilation units. The sMove s8 controls up to twice as many ventilation units: eight iV-Smart+ or iV14-Zero, or four iV-Twin+ or iV25 ventilation units

Both versions are available in flat and standard model. In addition to the pause operating mode, the standard version has the option of switching off the ventilation unit completely. Complete deactivation of the ventilati-on unit is not possible in the flat model (deactivation lockout).

The most important functions of your sMove s4 and s8 controls

Output level marking 1 – 4LED indicators of output level

Slide control

Key Pause/Off

LED indicator Pause/Off

LED indicator operating mode "Ventilation" / Filter change (blue)

LED indicator operating mode "Heat recovery" / Filter change (orange)

Key operating mode


After 30 seconds without touching the LEDs on the sMove controller switch off automatically. To make new entries or to view the remaining pause time, the controller must be activated.

Requirements: The controller is switched off.

• Press the Pause/Off key to activate the controller.

The LED indicators for the current operating mode and output of the controller light up.

or The remaining pause time LED indicators flash alternately.

You set the operating mode using the operating mode key . You can switch between the two operating modes heat recovery and continuous ventilation by repeatedly pressing the operating mode key .

Requirement: The controller is switched on.

Heat recovery

• Press the oprating mode button , until the orange coloured LED on the left side of the key lights up.

Continuous ventilation

• Press the oprating mode button , until the blue coloured LED on the left side of the key lights up.

Activating the control panel

Set operating mode

How to operate your sMove s4 and s8 controls

In this operating mode, the connected ventilation units are switched off.

Requirement: The controller is in heat recovery or continuous ventilation mode.

• Press the Pause/Off key for longer than five seconds.

The Pause/Off indicator LED lights up permanently white.

Operating mode Off (only in standard version)



When setting the pause function, the controller switches off the con-nected ventilation units. The pause time can be selected for one, two, four or eight hours. All ventilation units connected to the controller then restart in the previously stored operating mode and output level.

Requirement: The controller is in the operating mode heat recovery or continuous ventilation.

• To set the pause function, press the Pause/Off key repeatedly until the desired pause time is displayed.

1 x: 1 hour break

2 x: 2 hours break

3 x: 4 hours break

4 x: 8 hours break

The respective light indicator to the left of the slider and the light indicator Pause / Off flash alternately in white.

Pause function

1 h

4 h

8 h

2 h

The pause can be interrupted at any time by selecting another output level.

If the controller is in pause, you can display the remaining pause time.

Requirement: The controller is in pause function.

• Activate the display by pressing any key.

The LED indicator on the left of the slider for the remaining pause hours and the LED indicator Pause/Off flash alternately in white.

• Indicator light next to Pause/Off key = 0 hours • Lowest indicator light next to slider illuminated = 1 hour • Each additional indicator light upwards = 1 additional hour

1 h

6 h

je + 1 h



1. Place your finger on the slider for approx. 1 second. The slider is activated.

2. Move your finger on the slider to the desired output level.

The LED indicator next to the slider shows the set output level.

Set output: predefined levels

Set output: infinitely variable


• Press the key with the symbol of the desired output level.

fan performance 25 % (Level 1)




The LED indicator to the left of the selected fan symbol is permanently white.


• Place your finger on the top key of the slider for more than 5 seconds.

The uppermost LED indicator next to the slider flashes white.

Set output: Boost function



After 180 days, the sMove controller reminds you to change the filters of your ventilation units. If the filter has to be changed, the orange or blue light flashes permanently, depending on the operating mode the cont-roller is currently in. After you have changed the filter, you must confirm the change on the controller.

Requirement: The orange or blue light indicator flashes continuously.

• Press the key for longer than 5 seconds.

The LED indicator no longer flashes.

The filter change interval is reset to the begnning.

Confirm filter change



The MZ-Home controller is an electronic control unit for controlling the in-VENTer® ventilation units with heat recovery. Thanks to its unique and inno-vative Clust-Air® technology (multi-zone control), the MZ-Home controller controls up to four areas within a house and thus ensures individually tailored ventilation for each residential area.

For each area, operating mode and output level can be set via weekly timer or manually. The controller can be used as a basic module or with additional connected sensors, expanding its range of functions. The external interface allows the connection of a potential-free on/off switch for each zone (area), the connection of an optional VOC (volatile organic compound, "bad air") or CO2 sensor, the connection of a pressure sensor. In addition, integration into an existing house control system is possible via an analogue input. The MZ-Home controller actively controls the connected ventilation units in the operating modes:

• Heat recovery (HR)• Continuous ventilation (VENT)• Pause function (Pause)

An integrated humidity sensor monitors the relative humidity in each venti-lation area and automatically switches the ventilation unit to the dehumidifi-cation mode when it is switched on.

The most important functions of your MZ-Home controller

Description

Display

Acrylic glass cover

Control panel

The display in the upper part of the control unit shows the menu you are currently using. It has a backlight which is automatically activated when any navigation ar-row is touched. After 20 seconds without input, the display switches off automatically.

The 4 navigation arrows in the lower part of the operating unit are capaci-tive keys. By touching any navigation arrow, the display unit in the upper part of the control unit is activated, the start screen is displayed and the controller can be operated.

Control panel


Operation

Switch on display

Note: The display switches off automatically after 20 seconds (factory setting) without input.

Touch any navigation arrow. g The start screen is displayed.

The initial screen

The initial screen displays the inVENTer logo, the date, and the current time. Depending on the situation, you will also be informed about current deviations from the weekly timer (e.g. dehumidification of a zone; no humidity sensor is connected to a zone.)

You can access additional functions from the initial screen:

• Touch the navigation arrow s to go to the Output/Manual control menu. There you can manually control the weekly timer inputs for a certain interval. The manual control is not permanent, but only valid for the selected interval.

• Touch the navigation arrow w repeatedly repeatedly to switch through the screens listed below:

> Initial screen> Main menu Zone display> Main menu Settings

• Touch the navigation arrow v to switch between the above screens the other way around.

• To return to the respective parent menu, use the navigation arrow to select the first line of the respective submenu and touch v.

• Home function: Touch the navigation arrows v and w at the same time to go straight from a menu to the initial screen.

inVENTer MZ-Home No sensor zone 101.01.2018 15:08

Name of device

Date

Time

Additional information(situational)

Manufacturer

Home function:

How to operate your MZ-Home control


Zone 1 HR t | rF | LEAct : 24°C| 32%| Set : --- | 80%|

In addition to the pre-programmed settings of the weekly timer, the zones can be controlled manually in the Manual control menu if required. Manual control can be carried out separately for each zone.Requirement: You are in the start screen.

1. Touch the navigation arrow s g You are in the Output menu.2. Use the navigation arrows v / w to select the zone.3. Set the output and the operating mode. (see section Programming

the weekly timer)4. Use the navigation arrow s to select the duration.5. Touch the navigation arrow v / w to set the duration of the manual

control.6. Touch the navigation arrow until you are back on the start screen. You have changed the weekly timer settings for the current period (the change does not have a permanent effect).

The Zone Display main menu displays the current settings for each zone. No settings can be made.

The zones are selected by touching the navigation arrows s and .Touch the navigation arrow s to display the next zone.Touch the navigation arrow to display the previous zone.

The main menu Settings contains all navigation points (submenus) you need to configure the MZ-Home:

To select the individual items, carry out the following steps:1. Touch the navigation arrows / s until the desired menu item is

displayed.2. Touch the navigation arrow w, to confirm the menu item. You are

now in the selected submenu.

The most important menus for you are explained below.

• Language• Switch off all ventilation units• Weekly timer• Inputs• Limit values• Filter change

• Output levels• Operating hours• Display• Date & Time• Informations• Activate humidity sensor


> output <zone1> output : mode : HR duration : 02 h

settings >language

Output/Manual control menu

Main menu Zone display

Main menu Settings

Markierungspfeil

AuswahlmöglichkeitUntermenü

Anzeige aktuelles Menü

Actual operating mode

Zone

Actual temperature

Actual relative humidity

Limit value relative humidity

Output level if limit value is exceeded

Actualoutput level


settings >weekly timer

weekly timer >zone 1 on

>weekly timer zone 1 off

>weekly timer sun 00 - 04 h HRLE:

weekly timer> sun 02 - 04 h HR LE:

Requirements: Your are in the Settings main menu.

1.1. Switching on the weekly timer

In the Weekly timer menu, you can switch the weekly time on or off for each zone and adapt the weekly schedule for the weekly time switch.

How to switch on the weekly time switch for a zone:

1. Touch the navigation arrow s / , until the menu item weekly timer is displayed.

2. Touch the navigation arrow w.3. Use the navigation arrow s to select the zone to be switched on.4. Touch the navigation arrow w to confirm the selection. g The <off> indicator blinks.5. Touch the navigation arrow w. The display will no show <on>. You have activated the weekly timer for the selected zone.

Now you can program the weekly timer.

Touch the navigation arrow w to enter the submenu for setting the weekly time schedule.

1.2. Selecting the day of the week

Requirements: The weekly timer for the selected zone is active.1. Touch the navigation arrow s / , until the marker > points to the

weekday menu item.2. Touch the navigation arrow w to confirm. g The day of the week indicator flashes.3. Use the navigation arrow / s to select the weekday.4. Touch the navigation arrow v to confirm. g The day of the week indicator stops flashing. You have selected the day of the week.

1.3. Selecting the operating mode

With this option you can set one of the actively selectable operating modes for the selected interval:• Heat recovery (HR)• Continuous ventilation (VENT)• Pause function (Pause)

1. Programming weekly timer

weekly timer> mon 02 - 04 h HRLE:



weekly timer mon 04 - 06 h VENT >LE:

weekly timer mon 04 - 06 h VENT >LE:

weekly timer mon >02 - 04 h VENTLE:

Note: The operating mode "Dehumidification" (EF) is triggered by excee-ding the set limit value at the humidity and temperature sensor. It cannot be set manually.

Requirement: The weekly timer for the selected zone is active.1. Touch the navigation arrow s / , until the marker > points to the

operating mode menu item.2. Touch the navigation arrow w to confirm. g The operating mode indicator flashes.3. Use the navigation arrow / s to select the operating mode.4. Touch the navigation arrow v to confirm. g The operating mode indicator stops flashing. You have set the operating mode.

1.4. Selecting the time interval

The time interval defines the period in which the settings made are active.The time spans are displayed as the time of day. The controller offers12 predefined intervals with two hours per interval.


time interval menu item.2. Touch the navigation arrow w to confirm. g The time interval indicator flashes.3. Use the navigation arrow / s to select the time interval.4. Touch the navigation arrow v to confirm. g The time interval indicator stops flashing. You have selected the time interval.

1.5.Selecting the output level

The Output level option assigns the defined power levels 1, 2, 3 or the pause function to the time interval.


output level menu item.2. Touch the navigation arrow w to confirm. g The output level indicator flashes.3. Use the navigation arrow / s to select the desired output level.4. Touch the navigation arrow v to confirm. g The output level indicator stops flashing. The fan performance (output level) is selected.

If you have programmed a certain interval in a zone, you can accept it for all weekdays in this zone. To activate the transfer function, go to the end of the weekly time switch submenu.

Output level 1:Output level 2:Output level 3:Pause function: no bars

weekly timer mon 02 - 04 h> HR LE:

weekly timer mon 02 - 04 h> VENTLE:



settings

>filter change

filter change Filter changed?>duration: 14 weeks rest : 8 weeks

filter change>Filter changed? duration: 14 weeks rest : 0 weeks

The MZ-Home controller can remind you to change the filter if you wish.

Note: The contamination of the filters is not measured automatically. You must set an interval based on your own observation. The factory setting is an interval of 14 weeks.

Requirements: Your are in the settings main menu.1. Touch the navigation arrow s / , until the menu item filter change

is displayed.2. Touch the navigation arrow w. g The filter change submenu is opened.3. Use the navigation arrow s to select the Duration menu item.4. Touch the navigation arrow w to confirm the selection. g The duration indicator flashes.5. Use the navigation arrow / s to increase / decrease the number

of weeks between filter change.6. Touch the navigation arrow v to confirm. g The duration indicator stops flashing. You have set your desired filter change interval.

If the filter has to be changed, the filter change display opens instead of the start screen. After you have changed the filter, you must confirm the change on the controller.

Requirements: Your are in the settings main menu.1. Touch the navigation arrow s / , until the menu item filter change

is displayed.2. Touch the navigation arrow w. g The filter change submenu is opened.3. Use the navigation arrow s to select the Filter changed? menu item.4. Touch the navigation arrow v to confirm.

The filter is considered to have been changed and the display resets to the set filter change interval.

2. Set reminder for filter change

3. Confirm filter change

settings

>filter change

filter change



settings

>output levels

display>brightness: 80 % duration : 20 sec

>output levels = 25 % = 35 % = 60 %

ABBBBBinVENT erBBBBBBBBBWRGBBBB BBBBBBBBBBBBB27 ° CBBBBB33%rHBBB02 . 0 4 . 20 1 4BBBBB 1 2 : 42

settings

>display

display>brightness : 60 % duration : 20 sec

The three power levels and the dehumidification mode are assigned to a specific value ex works (see illustration on the left) and can be changed in 5% steps.The percentage assignment of the performance levels depends on the ventilation concept that was created for you. We recommend that you assign the value for which your ventilation concept is designed to power level 2 and leave the ventilation system at this level by default

If you want to change the performance levels of the fans, proceed as follows:

Requirements: Your are in the settings main menu.1. Touch the navigation arrow s / , until the menu item output levels

is displayed.2. Touch the navigation arrow w. g The output levels submenu is opened.3. Use the navigation arrow s / to set the desired output level (fan

performance).4. Touch the navigation arrow w to confirm the selection. g The fan performance indicator flashes.5. Use the navigation arrow / s to increase / decrease the output in

5 % increments.6. Touch the navigation arrow v to confirm. g The fan performance indicator stops flashing. Sie haben die Leistungsstufe für die Betriebsarten Wärmerück- gewinnung und Durchlüftung neu eingestellt.

The Display submenu is used to adjust the brightness of the backlight during input and the duration of the backlight after the last input.

Requirements: Your are in the settings main menu.1. Touch the navigation arrow s / , until the menu item display is

displayed.2. Touch the navigation arrow w. g The display settings submenu is opened.

5.1. Adjusting the brightness

Requirements: You are in the display menu.1. Touch the navigation arrow s / , until the marker > points to the

brightness menu item.2. Touch the navigation arrow w. g The brightness indicator flashes.3. Use the navigation arrow / s to increase / decrease the displays

brightnes.4. Touch the navigation arrow v to confirm. g The brightness indicator stops flashing. You have adjusted the brightness of the display.

4. Define output levels

5. Adjust display settings



display brightness: 80 %>duration : 20 sec

settings >date & time

date & time>date 01.01.2018 time 06:08 weekday wed




5.2. Setting the lighting duration

The illumination duration indicates how long the screen should remain on after your last entry.

Requirements: You are in the display menu.1. Touch the navigation arrow s / , until the marker > points to the

duration menu item.2. Touch the navigation arrow w. g The lighting duration indicator flashes.3. Use the navigation arrow / s to increase / decrease the displays

lighting duration.4. Touch the navigation arrow v to confirm. g The lighting duration indicator stops flashing. You have set the illumination duration.

Requirements: Your are in the settings main menu.1. Touch the navigation arrow s / , until the menu item date & time

is displayed.2. Touch the navigation arrow w. g The date & time submenu is opened.

6.1. Setting the date

Requirements: You are in the date & time menu.1. Touch the navigation arrow s / , until the marker > points to the

date menu item.2. Touch the navigation arrow w. g The day indicator flashes.3. Use the navigtion arrow / s to set the current day. g The current day is set.4. Touch the navigation arrow w. g The month indicator flashes.5. Use the navigtion arrow / s to set the current month. g The current month is set.6. Touch the navigation arrow w. g The year indicator flashes.7. Use the navigtion arrow / s the current year. g The current year is set.8. Touch the navigation arrow v three times. g You are back in the date & time submenu. You have set the date.

6. Setting the date and time

display brightness: 80 %>duration : 50 sec

settings

>display



>Sprache < Deutsch >

settings >information

language >< english >

information MZ-HomeHW:1.00 SW:1.06fSN: 1707181234

6.2. Setting the time

1. Touch the navigation arrow s / , until the marker > points to the time menu item.

2. Touch the navigation arrow w. g The hours indicator flashes.3. Use the navigtion arrow / s to set the hour. g The hour is set.4. Touch the navigation arrow w. g The minutes indicator flashes.5. Use the navigtion arrow / s to select the minute. g The minute is set.6. Touch the navigation arrow v two times. g You are back in the date & time submenu. You have set the time.

6.3. Setting the day of the week

1. Touch the navigation arrow s / , until the marker > points to the weekday menu item.

2. Touch the navigation arrow w. g The day of the week indicator flashes.3. Use the navigation arrow / s to set the weekday. g The weekday is set.4. Touch the navigation arrow v once. g You are back in the date & time submenu. You have set the day of the week.

The default menu language is changed in the language submenu.

Requirements: Your are in the settings main menu.1. Touch the navigation arrow s / , until the menu item language

[Sprache] is displayed.2. Touch the navigation arrow w. g The language submenu is opened.3. Use the s navigation arrow s to select the language currently set. g The marker > points to the currently set language.4. Use the navigation arrow w to select your desired language. g You are back in the settings main menu. You have changed the language setting.

If you contact our technical service, you may be asked for the version of the hard- or software or the serial number of your MZ-Home. These can be found in the information menu.

Requirements: Your are in the settings main menu.1. Touch the navigation arrow s / , until the marker > points to the

information menu item.2. Touch the navigation arrow w to enter the submenu. The hardware (HW) or software (SW) version and serial number

(SN) are displayed.

7. Set the language

8. Retrieve information

date & time date 02.03.2019>time 10:58 weekday wed

date & time date 02.03.2019 time 10:58>weekday wed

date & time date 02.03.2019 time 10:58>weekday sun





>all fans off [x] No [ ] Yes

The MZ-Home has the possibility to disconnect all ventilation devices connected to the controller from the power supply at the same time. Use this function if you want to clean your ventilation units or change the dust filters.

Requirements: Your are in the settings main menu.1. Touch the navigation arrow s / , until the marker > points to the

All fans off menu item.2. Touch the navigation arrow w. g The All fans off submenu is opened.3. Use the navigation arrow s to select the YES option.4. Touch the navigation arrow w to confirm. → All ventilation units connected to the controller are switched off at

the same time.5. Touch the navigation arrow v once. g You are back in the All fans off submenu. You have switched off the ventilation units.

Switch on your ventilation units again after cleaning or changing the dust filters to ensure optimum air exchange in your living rooms.

To switch on the ventilation units again, carry out the steps described above and select the NO option.The ventilation units restart in the originally set operating mode.

all fans off [ ] No> [x] Yes

settings

>all fans off

9. Switch off all ventilation units

all fans off> [x] No [ ] Yes



Chapter III

The most important functions of your inVENTer inner covers


Overview of your inner cover Flair

To close and open the inner cover Flair, simply carefully move the panel of the inner cover evenly towards and away from the wall.

Start at the bottom of the inner cover: Slightly push the side lugs on the spacers where the cover is snapped into place inwards. Move each cor-ner away from the wall to release it from the base plate.

After all corners have been removed from the base plate, you can remove the inner panel.

Hold the cover so that the logo is on the bottom right. Place the panel straight on the base plate spacers. Carefully slide the cover toward the wall until the inner panel is closed.

Then pull the cover to the open position and the spacers will click into place. Now you can tilt the inner cover if necessary.

The inner cover Flair can be tilted upwards or downwards. This allows the air flow to be directed in a specific direction. In addition, outside noise can be further reduced in this way.

Tilting the inner panel from the open position

To tilt, press either the lower edge or the upper edge of the inner panel carefully towards the wall, depending on the desired direction.

If you want to open the inner cover completely again, simply pull the closed edge away from the wall until it clicks into place.

Removing the cover

Attaching the cover

Tilting the cover


Overview of your inner cover Classic

On the inside of the cover of the round inner panel, the upper side is marked "top" (green arrow).

Step 1

Hook the cover panel into the spacers from above. Make sure that the "Top" marking is on top and that the spacers snap into the upper guides. (You will find the guides on the inside of the panel.)

Step 2

1 Tighten the panel of the round inner cover to the upper hook by carefully pulling it over the two lower spacers towards the floor.

2 Make sure that the guides in the lower part of the panel audibly snap into the lower spacers of the base plate.

Step 3

Turn the inner cover panel first to close (to the right) and then to open again (to the left). If this is convenient, all guides are located on the spacers of the base plate and the panel of the round inner cover is fitted.

Attaching the cover


Overview of your inner cover Classic

Step 2

1 Now reach into the cover from below. Carefully pull the panel towards the floor. This will unhook the panel guides from the base plate spacers.

2 Pull the cover towards you.

Step 1

Turn the round inner cover panel to the left until it is completely open.

Step 3

Lift the panel of the round inner cover upwards

Step 4

Now you can access dust filters etc. This is important for cleaning the inVENTer ventilation system.

Removing the cover


Overview of your inner cover Quadra

Installing the cover in the closed state

Step 1

1 Hold the panel so that the printed inVENTer® lettering is upside down at the top of the cover. Insert the panel from above into the short, central lug of the base plate.

2 Fold the lower part of the panel toward the base plate.

Step 2

Grasp behind the lower edge of the cover. Pull the cover over the spacers. Snap the cover audibly into the two short lugs at the bottom of the base plate.

The attached inner cover is closed

Removing the cover from the closed position

When closed, there is no gap between the base plate and the panel of the inner cover.

Step 1

1 Reach behind the web at the bottom of the panel.2 Pull the cover in your direction until it is audible.

Step 2

1 Lift the panel upwards.2 Now you can access dust filters etc. This is important for cleaning the inVENTer ventilation system.


Overview of your inner cover Quadra

Removing the cover from the open position

Installing the cover in the opened state

Step 1Hold the panel so that the printed inVENTer® lettering at the bottom of the cover is normally legible.1 Insert the panel from above into the latching lugs on the two long spacers

of the base plate. The two short hooks of the cover snap into the long spacers.

2 Fold the lower part of the panel towards the base plate.

Step 2

Carefully pull the panel of the inner cover down at the lower edge over the spacers. Now engage the lower edge of the panel audibly into the long spacer in the lower part of the base plate.

The attached inner cover is open.

When open, there is an approx. 2 cm wide gap between the base plate and the panel of the inner cover.

Step 1

Grasp behind the lower edge of the panel. Carefully pull the panel towards the floor and then towards you. This will cause the lower part of the panel to hook out of the spacers on the base plate.

Step 2

1 Lift the panel upwards.2 Now you can access dust filters etc.

This is important for cleaning the inVENTer ventilation system.


Chapter IV

How to clean yourinVENTer ventilation units


The inVENTer ventilation systems are mostly maintenance-free. The filters, the drawer unit with heat accumulator, double air control unit and reversible fan as well as the wall mounting sleeve should be cleaned at regular intervals. We recommend cleaning the dust filters every three months. The half-yearly cleaning of the reversible fans, air control units and ceramic heat accumulators is sufficient.

Disconnect your ventilation unit from the power supply before cleaning.Wear protective gloves when cleaning.

1. How to change your filter

The dust filters are very durable and can be washed out several times. We recommend that you clean the dust filter every three months. Replace defective or excessively dirty dust filters. The optional pollen and activated carbon filters cannot be cleaned but must be replaced. Pollen filters should only be used during the pollen period for a maximum of 4-6 weeks. Disposal with household waste is possible. Replacement filters can be ordered from your inVENTer factory representative. You can also order via Amazon.com.

Step 1: Remove the inner cover panel (see chapter: "Overview of the most important functions of your inVENTer inner covers", page 23 ff.).

If present, unscrew the sound insulation insert.

Step 2: Remove the dust filter from the base plate of the inner cover.

Step 3: The dust filter can be cleaned under warm water with a bit of detergent. The optional pollen and activated carbon filters cannot be cleaned but must be replaced.

The filters must be completely dried before being reused. We recommend the use of replacement filters to bridge the cleaning time.

Step 4: Replace the new or cleaned and completely dried filter.

Step 5: Replace the inner cover panel (see chapter: "Overview of the most important functions of your inVENTer inner covers", page 23 ff.).

How to clean your inVENTer ventilation units

Step 1

Removing theinner cover panel

Step 3

Washing out the dust filter

Step 2

Removing the dust filter



Step 3: Mark the original position of the connectors. The three-pole plug can then be removed

Step 4: Remove all individual components of the ventilation unit one after the other from the wall mounting sleeve. All individual components have knobs or pull loops directed towards the interior to facilitate removal.

First pull out the reversible fans, if any, including the control units or spacers. The ceramic heat accumulators can then be pulled out.

Marking on the iV14-Zero Marking on the iV-Twin

2. How to remove the components of your ventilation unit

We recommend that the ceramic heat storage unit and inVENTron® be checked every six months for contamination and movement of the Xenion® reversible fan. Please observe the previous interruption of the power supply!

Step 1: Remove the panel of the inner cover (see chapter: "Overview of the most important functions of your inVENTer inner covers", page 23 ff.).

If present, unscrew the sound insulation insert.

Step 2: Remove the dust filter from the base plate of the inner cover.

For cleaning the thermal accumulator insert on the ventilation unit with round or square inner cover, the base plate of the inner cover must also be removed. A suitable hexagon key is attached to the base plate.

Pulling out the ceramic heat accumulator

Pulling out inVENTron®:air control units and reversible fan


Step 5: Disconnect the air control units from the reversible fan. They can be removed without tools: Place inVENTron® on a surface in front of you on a table. Use both hands to grasp adjacent fastening webs on the upper air control unit. Carefully bend both

webs outwards at the same time and remove them from the fan.

Step 6: Grasp the two not yet loosened fastening webs on the upper air control unit with one hand each. Carefully bend both fastening webs outwards and remove them.

Now you can remove the detached air control unit upwards. When the first air control unit is detached, turn the fan so that the remaining air control unit faces

upwards.

Step 7: Entfernen Sie das zweite Leitwerk wie oben in Schritt 5 und 6 beschrieben vom Xenion®-Ventilator.

Now you can clean the ceramic heat accumulator, the air control units and the fan.

3. How to clean the ceramic heat accumulator

Step 7

Removing the secondair control unit

Step 6

Removing an air control unitfrom the reversible fan

Step 5

Detaching the fastening webs from the Xenion® fan

For cleaning, vacuuming with a vacuum cleaner or blowing out with compressed air is usually sufficient.

In case of heavier soiling, the ceramic heat accumulator with foam insulation (without reversible fan) can be washed out under running warm water without detergent. For installation, the ceramic heat accumulator must be completely dry again. The foam insulation is water-repellent and only becomes damp on the surface.

Then clean the wall sleeve from the inside with a damp cloth.

Washing out the ceramic heat accumulator



4. How to clean the reversible fans and the air control units

The control units are removed from the Xenion® fan

We recommend checking the reversible fan for dirt every six months and cleaning it once a year, preferably before the heating period. You can only clean the reversible fan after the reversible fan has been removed from the wall sleeve (see section: "How to remove the components from your ventilation unit", page 31).

Step 1: The fan blades can be carefully cleaned with a brush or a soft damp cloth. Never immerse the fan in water!

Note: In regions with a high salt content in the air, the metal protective grid on the reversible fan of the iV25 and iV-Twin ventilation units can also be wiped with a slightly oily cloth. The protective grid can be unscrewed for this purpose.

Step 2: The air control units can be washed under running warm water or cleaned with a brush. Possibly existing felt strips can easily be knocked out.

Step 3: When the air control units are completely dry, reattach them to the Xenion® fan. The broad air control unit must be on the side with the fan shield. The narrow air control unit has a recess for the fan cable. When assembling, place the control unit so that the cable can be placed in the recess after the control unit has been fixed.

Step 3

Assembly:Wide air control unit to the side

with fan shield

Step 2

Cleaning of an air control unit under running water

Step 1

Cleaning the fan with a brush



5. How to reassemble your ventilation unit after cleaning

Wipe the wall mounting sleeve or Inventin® insert, if present, with a damp cloth before reinserting all components.

Slide all components back into the wall mounting sleeve in reverse order to removal:

Step 1: First push the dried heat accumulator into the wall sleeve as far as it will go.

Step 2: Then push the reversible fan including the control units back into the wall sleeve. The side of the fan on which the fan shield is located must face the ceramic heat accumulator. If there is a metal protective grille on the fan, it must point towards the interior after insertion.

Step 3: The three-pole plug must be plugged in correctly (the marked line must match).

Step 4: Replace the filter and the sound insulation insert, if present. For the iV-Twin or a version with sound insulation insert, the insert must be screwed on.

Step 5: Replace the inner cover in the open state. Open the inner panel again and switch on the ventilation unit again.

Step 3

Put it together: Markings match

Step 2Step 1

Insert the heat accumulator Inserting inVENTron®: air control units and Xenion® fan



Date Component(s) Measure

Service inVENTer ventilation systems: Cleaning protocol

IIn the following table you can enter all the cleaning and inspections carried out on your ventilation units.

Overview of cleaning measures

Dust filter: Clean or (if necessary or worn) replace.

Pollen and activated carbon filter: Replace.

Cermaic heat accumulator: Wash out or suck out under running warm water.

Do not clean in the dishwasher!

Air control units: Clean under warm running water.

Reversible fan: Clean with a dry cloth or brush. Never clean with water!

Inner cover: Wipe surfaces with a damp cloth.

Controller: Wipe surfaces with a damp cloth.

Sound insulation accessories: Replace sound protectors. Slightly knock out sound insulation inserts, replace if worn.

Wind protection accessories: Wash under running warm water.


Troubleshooting

If faults should occur, please first check whether the fault can be rectified yourself by observing the following instructions. If the fault cannot be rectified, please contact your inVENTer representative.

Malfunction Possible cause Solution

Fan does not run No electrical voltage Switch power off and on again (mains fuse)

Fan jammed Switch off the controller! Remove object.

Controller/power supply defective

Replace controller/switching power supply unit.

Fan defective Check fan and replace if necessary.

Cold supply air Controller in operating mode "Continuous ventilation"

Check operating mode on the controller, no heat recovery takes place in ventilation operating mode.

Installation errors Check that the 3-pole plug is correctly inserted.

Make sure that the shield on the fan is directed in the direction of the ceramic heat accumulator.

Air flow ratetoo low

Inner cover not opened properly

Complete opening of the inner cover.

Dust filter heavily soiled Clean the dust filter. Dispose of worn or defective filters.

Pollen filter inserted /heavily soiled

If a pollen filter is used, the air flow rate is reduced, pollen filters should only be used during the pollen flight time, if necessary change the pollen filter.

Heat accumulator heavily soiled

Clean the heat accumulator

Noise level too high

Fan blades heavily soiled

Clean the fan blades

Heat accumulator not pushed outwards

Push the heat accumulator into the wall sleeveuntil it rests against the stop band.

Additional sound insulation required

Outside noise (street noise) can be reduced by using the sound protector or the sound insulation insert if necessary.

Service inVENTer ventilation systems: Troubleshooting


Customer support

In the case of a complaint or customer service request, please contact your factory representative or the installation company responsible for installing your ventilation system.

Please have one of the following numbers ready:

Order number:

Invoice number:

Delivery note number:

Contact facory representative:

Reference person:

Company:

Street, house number:

Postcode, City:

Contact installation company:

Reference person:

Company:

Street, house number:

Postcode, City:

In case of missing contact data please contact our factory.

inVENTer GmbHOrtsstraße 4aD-07751 LöberschützTelephone: +49 (0) 36427 211-0Telefax: +49 (0) 36427 211-113E-Mail: [email protected]: www.inventer.eu

Service inVENTer ventilation systems

inVENTer GmbHOrtsstraße 4aD-07751 LöberschützTelephone: +49 (0) 36427 211-0Telefax: +49 (0) 36427 211-113E-Mail: [email protected]

www.inventer.eu

Article number: 6005-0004Dated 12/2018

Subject to technical changes withoutnotice. No liability for printing errors.

for your inventer ventilation system · 2019. 5. 22. · 1 2. information for your inventer...

Documents