fleetshield is a new exciting product from dulux catering for · pdf filefleetshield is a new...
TRANSCRIPT
1
FleetShield is a new exciting product from Dulux catering for
commercial vehicle (CV) refinishing.
FleetShield offers 5 different premium quality two pack bases, increasing
colour range and superior coverage.
A complete range of solid colour tinters and pearls tinters to tint, match
and customise any single layer 2K colour.
1200 colours are available for the Dulux 2K PR system with a approximately
200 colours added from local matching & aligned with Snapshot.
FleetShield offers a complete range of ancillary products, primers, clears
and a range of hardeners and thinners to suit all temperatures and job
sizes.
Flattening base for reduced gloss levels.
A complete range of products to suit plastic parts.
2
Base Line Shade Max Tint
By Weight
Colours which can be Tinted
Red Base 428-S0011 20% Red, maroon, dark orange
Yellow Base 428-S0062 20% Yellow, mid to light orange, bright green
Clear Base 428-S0047 30% Mid to dark blue, green and purple, pearl
White Base 428-S0204 20% Light blue, green, purple, light grey and all white.
Black Base 428-89943 20% Mid grey to Black
RED_BASE___ _ YELLOW BASE___________CLEAR BASE___________ CLEAR /WHITE BASE
3
White Base 428-S0204 is aligned with Autospeed PR 427-T0204.
Replaces HS White 488-89289 with Approx 20% less pigment
Red Base 428-S0011 is aligned with Autospeed PR 427-T0011.
Yellow Base 428-S0062 is aligned with Autospeed PR 427-T0062.
Black Base 428-89843 is aligned to 2K Black 488-89843
and is unchanged.
4
Break down of the 38 Tinters
Reds 12
Oranges 2
Yellows 6
Greens 4
Blues 7
Violets 2
Blacks 4
White 1
38 tinters
30 x 0.9L tinters
8 x 3.7L tinters
4 x reduced strength
Tinters included
PR 2K tinters are used to tint the 5 Bases
5
46 Pearl tinters can be used to match and customise colours.
Mixture of Mica and special effect pearls.
9 special custom pearls.
Can be mixed into Clear base.
Can be mixed into coloured bases.
Mixing
TBA
6
AUTOSPEED MT Flat Base
485-89915 x 0.9L
Used to achieve
Matt Finish 10% Gloss
Satin finishes 30% Gloss
Semi Gloss 50% Gloss
Mixing
Matt Finish 70 – 80% by weight
Satin Finish 20 – 30% by weight
Semi Gloss 30 – 40% by weight
*MT Flat Base is mixed in after hardening colour
7
AUTOSPEED Flex Additive
485-89930 x 0.9L
Add to primer, colour and clear
Add 20% Flex Additive prior to hardener
AUTOSPEED Plastic Cleaner
485-S0017 x 4L
Cleaning with anti static properties
AUTOSPEED Plastic Primer
485-89943 x 5L
Adhesion to a wide range of plastic substrates
8
Hardeners
2:1 Mixing Ratio AUTOSPEED RP Hardener 980-89790 (fast)
AUTOSPEED 2K Hardener Normal 980-89290
AUTOSPEED Hardener Slow 980-S0028
Hardeners come in 1L and 2.5L sizes
Thinners
10 – 20% Thinning Ratio AUTOSPEED RP Thinner 920-89819 x 20L.
AUTOSPEED 2K Normal 920-89292 x 20L.
AUTOSPEED 2K High Temp 920-89847 x 20L.
AUTOSPEED 2K X Slow 920- 89963 x 4L.
9
Etch
Primers
Primer
Fillers
Aerosol
Primers
10
Snapshot is a spectrophotometer
designed to read colour for
easier Identification.
Works in conjunction with iPhone
and Android phones.
Dulux FleetShield app is now available for iPhone and iPad
through iTunes store
Dulux FleetShield app is now available for Android devices
through Google Play Store
11
http://duluxrefinish.rockpaint.co.jp/duluxrefinish
12
1. Click on Mix
Formula Search
which will open
this page.
2. Click on Fleet
Shield.
13
1. Select Car
Manufacture –
Commercial
Vehicles.
2. Type in Colour
code if known
3. Or
4. Type in colour
name if known
Follow on with normal Micom mixing
14
Viscosity is the measure of a fluid’s resistance to flow
Conditions that cause higher viscosity
Paint is cold especially during winter months
Container not sealed properly in storage
Container left opened to allow solvent evaporation
Using catalysed product that is past its pot life
Results of high viscosity paint
Harder application
Orange peel
High film build
Trapped air
Trapped solvent causing solvent boil
15
Hold viscosity cup by handle & completely submerge into paint
Hold stop watch in other hand, ready to start
Lift viscosity cup out of paint and start stop watch immediately
As soon as paint flow from cup breaks, stop the stop watch.
Check time on stop watch to Technical Data Sheet.
If time is out more than 2 -3 seconds either side, add reducer
Test again
Spray Viscosity
Ford Din 4 @ 250C 18 – 20 seconds
Plastic
Alloys &
Aluminium
Steel
Fibreglass
Curtains
PPE
1. Clean surface areas
with Plastic cleaner
965-S0017.
2. New plastic sand
with grey scouring
pad.
3. Repairs sand with
P240 – P320
4. Clean again Plastic
Cleaner
1. Clean areas with
Prepwash 965-
89784.
2. If required sand
repair areas P80-
P120 for body fillers
3. No repairs sand with
P180-P240
4. Red scourer for AL
5. Clean again with
Prepwash
6. No Prepwash on
body fillers
Nitrile gloves and dust /
particle mask
1. Alloys-No Repairs
CV Ultraetch or
DP42
2. Alloys Repairs
CV Ultraetch or
DP42 + HS Primer.
3. Steel
CV Ultraetch or
DP42 or Epoxy
Urethane primer,
HS Primer .
4. Fiberglass
Epoxy Urethane
Primer + HS primer
1. Apply Plastic Primer
485-89943.
2. Single wet coat
3. Allow to flash of
3 – 5 mins before
applying topcoats
Nitrile Gloves, Respirator /
air feed hood, Overalls &
eye protection
1. FleetShield 2:1 2K
mix colour.
2. 2:1:10%-20%
3. 5-10min flash off
between coats.
4. Air Dry overnight
5. Baking
30min@60oC
6. Infrared 8-20 min
depending on type
of Infra Red.
1. FleetShield 2:1 2K
mixed colour with
Flex Additive 485-
89930.
2. Plastic Parts mix
5:1 then mix at 2:1
with Hardener.
3. Curtains mix the
same.
Nitrile gloves, overalls,
Air Feed Hood & eye
protection
Substrate Preparation Primer Topcoat
Alw
ays re
fer to
Tech
nic
al D
ata
Sh
eets
& S
DS
5 Year Standard Warranty
Heavy Steel
(Chassis)
New
Heavy Steel
(Chassis)
Refurbishment
PPE
1. Degrease surface
areas with
Prepwash.
2. Sand P80 to P120
to remove rust,
flaking paint.
3. Sand P240 – P320 +
Red scouring pad to
abrade surface for
adhesion.
4. Clean again
Prepwash
1. Abrasive blast to
remove Mill Scale to
SA2.5 Standard*.
2. Clean with Prepwash
3. Sand with P80 to
P180
4. Clean again with
Prepwash. *SA2.5 Standard refers to
cleanliness of steel. Very
thorough blast cleaning.
Near white metal 85%
clean.
Nitrile gloves and dust /
particle mask
1. Etch Primer. CV
Ultraetch or DP42 or
Epoxy Urethane
Primer
2. Repairs
HS Primer
Nitrile Gloves, Respirator /
air feed hood, Overalls &
eye protection
1. FleetShield 2:1 2K
mix colour.
2. 2:1:10%-20%
3. 5-10min flash off
between coats.
4. Air Dry overnight
5. Baking
30min@60oC
6. Infrared 8-20 min
depending on type
of Infra Red.
Nitrile gloves, overalls,
Air Feed Hood & eye
protection
Substrate Preparation Primer Topcoat
Alw
ays re
fer to
Tech
nic
al D
ata
Sh
eets
& S
DS
5 Year Standard Warranty
Dulux Refinish Etch
Primer such CV
Ultraetch , DP42 and
Epoxy Urethane
Primer can be
topcoated directly
Identify whether the
Paint spec requires a
special protective
coating e.g. Zinc or
needs temperature
ratings prior to primer
coats
18
OEM Commercial Vehicles.
CV Body Builders.
CV Truck Repair.
Trailer Manufacturers.
PV Body shops who use single layer solid colours as
opposed to basecoat/clearcoat.
Retail and Inspiration opportunities.
PV Distributors.
19
This range of product contains Isocyanates
and Solvents.
Toxic fumes and vapours can be harmful.
Always wear PPE equipment.
Always refer back to Technical Data Sheets
& Safety Data Sheets.