field device manager express - honeywell · r430 field device manager express express software...

Honeywell Process Solutions

Field Device Manager Express

Software Installation User's Guide

EP-FDM-02430X

R430

June 2012

Release 430

Honeywell

ii Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012

Notices and Trademarks

Copyright 2010 by Honeywell International Sárl. Release 430 – February, 2012

While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may be stated in its written agreement with and for its customers.

In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and specifications in this document are subject to change without notice.

Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell International Inc.

Other brand or product names are trademarks of their respective owners.

Honeywell Process Solutions

1860 W. Rose Garden Lane

Phoenix, AZ 85027 USA

1-800 822-7673

R430 Field Device Manager Express Express Software Installation User's Guide iii June 2012 Honeywell

About This Document

This guide describes how to install Field Device Manager (FDM) Express. For the sake

of brevity, this guide does not repeat the applicable general guidelines, considerations,

cautions, and so on that are covered in the other Experion system guides.

Release Information

Document Name Document ID

Release Number

Publication Date

Field Device Manager Express Software Installation User's Guide

EP-FDM-02430X

430 April 2012

References The following list identifies all documents that may be sources of reference for the material

discussed in this publication.

Document Title Doc ID

Experion Software Installation and Upgrade Guide —

FDM R430 User’s Guide EP-FDM-11430

Support and Other Contacts

iv Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012

Support and Other Contacts

United States and Canada

Contact: Honeywell Global Technical Support Center

Phone: 1-800-423-9883

Email [email protected]

Europe, Middle East and Africa (EMEA)

Contact: Honeywell Technical Assistance Center

Phone: +44 1202645583


Other Regions

Contact: Honeywell Global Technical Support Center


Training Classes

Honeywell Automation College:

http://www.automationcollege.com

mailto:[email protected]



http://www.automationcollege.com/

Symbol Definitions

R430 Field Device Manager Express Express Software Installation User's Guide v June 2012 Honeywell

Symbol Definitions The following table lists those symbols used in this document to denote certain conditions:

Symbol Definition

ATTENTION: Identifies information that requires special

consideration.

TIP: Identifies advice or hints for the user, often in terms of

performing a task.

REFERENCE -EXTERNAL: Identifies an additional source of

information outside of the bookset.

REFERENCE - INTERNAL: Identifies an additional source of

information within the bookset.

CAUTION

Indicates a situation which, if not avoided, may result in equipment or work (data) on the system being damaged or lost, or may result in the inability to properly operate the process.

CAUTION: Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

CAUTION symbol on the equipment refers the user to the product

manual for additional information. The symbol appears next to required information in the manual.

WARNING: Indicates a potentially hazardous situation, which, if not

avoided, could result in serious injury or death.

WARNING symbol on the equipment refers the user to the product

manual for additional information. The symbol appears next to required information in the manual.

WARNING, Risk of electrical shock: Potential shock hazard where

HAZARDOUS LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or 60 VDC may be accessible.

Symbol Definitions

vi Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012

Symbol Definition

ESD HAZARD: Danger of an electro-static discharge to which

equipment may be sensitive. Observe precautions for handling electrostatic sensitive devices.

Protective Earth (PE) terminal: Provided for connection of the

protective earth (green or green/yellow) supply system conductor.

Functional earth terminal: Used for non-safety purposes such as

noise immunity improvement. NOTE: This connection shall be bonded to Protective Earth at the source of supply in accordance with national local electrical code requirements.

Earth Ground: Functional earth connection. NOTE: This

connection shall be bonded to Protective Earth at the source of supply in accordance with national and local electrical code requirements.

Chassis Ground: Identifies a connection to the chassis or frame of

the equipment shall be bonded to Protective Earth at the source of supply in accordance with national and local electrical code requirements.

R430 Field Device Manager Express Express Software Installation User's Guide vii June 2012 Honeywell

Contents

1. BEFORE YOU BEGIN ....................................................................9

1.1 Planning and design guidelines .................................................................... 9

1.2 Installation components and requirements ................................................. 9 Package information ..............................................................................................................9 FDM Express installation components ...................................................................................9 License information .............................................................................................................. 10 Hardware and software requirements .................................................................................. 11 FDM Express compatibility with Experion releases .............................................................. 11

1.3 Installation Scenario ..................................................................................... 12 Overview .............................................................................................................................. 12 Typical Architecture of FDM Express ................................................................................... 12

2. FDM EXPRESS INSTALLATION ................................................. 13

2.1 Installing FDM Express ................................................................................. 13 Prerequisites ........................................................................................................................ 13 To install FDM Server .......................................................................................................... 14

2.2 Installing FDM Client ..................................................................................... 20 Prerequisites ........................................................................................................................ 20 To install FDM Client ............................................................................................................ 20

3. POST INSTALLATION TASKS .................................................... 25

3.1 Updating the FDM license ............................................................................ 25 Prerequisites ........................................................................................................................ 25

3.2 Executables required in DEP exception list ............................................... 27 Adding executables to Data Execution Prevention (DEP) execution list .............................. 27

3.3 Configuring the network information .......................................................... 28

3.4 First logon ...................................................................................................... 28

4. FDM MAINTENANCE ................................................................... 31

4.1 Overview ........................................................................................................ 31 Before starting FDM maintenance ........................................................................................ 31

4.2 Modifying FDM components ........................................................................ 32

Contents

viii Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012

4.3 Repairing FDM components ......................................................................... 36

4.4 Removing FDM ............................................................................................... 40

R430 Field Device Manager Express Express Software Installation User's Guide 9 June 2012 Honeywell

1. Before You Begin

1.1 Planning and design guidelines FDM Express is an on-the-go version of Field Device Manager designed for use in the

maintenance shop and suitable for installation in a Win 7 laptop or desktop PC. It is

important that you plan the installation of FDM Express, so please refer to EP03-480-,

Field Device Manager Express Specifications, for information on PC hardware, PC

operating system, and peripheral requirements. Also, refer to the specifications for

details about performance and operational limits and to decide upon the number of tag

licenses you need. Up to 1000 tags are supported by FDM Express.

ATTENTION

FDM server installation includes installation of Microsoft SQL Server 2008 Standard Edition and Microsoft SQL Server 2008 Service Pack1. As a result, FDM server installation takes considerable time.

1.2 Installation components and requirements

Package information

Component Software Media Software Media

Type

FDM R430 setup software Field Device Manager Software R430.1 DVD – 1

DVD

Microsoft SQL Server

2008 R2 SP1

Field Device Manager Software R430.1 DVD – 2

DVD

FDM Express License Field Device Manager License CD R430.1

CD

FDM Express installation components

FDM Express installation supports the following components.

FDM Server: FDM Server forms the core of FDM application. It manages the FDM

client and interacts with HART and PROFIBUS devices through the Remote

Communication Interface (RCI). It stores all persistent information related to the

1. Before You Begin

1.2. Installation components and requirements

10 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012

devices, networks, and FDM users. For FDM Express Server installation, FDM

Client and RCI are required and they are automatically selected and installed during

the installation.

FDM Client: FDM client is the user interface component of the FDM application.

The client enables you to connect-to FDM Server and performs various

functionalities supported by FDM.

FDM RCI: Remote Communication Interface (RCI) is the component in FDM that

manages the interaction with devices connected to the communication interfaces. It

is also included in the FDM Express installation. The following table lists the

communication interfaces and the respective device which can be connected.

Communication Interfaces Devices

HART Profibus

RS-232 HART Modem Supported Not applicable

RS-485 HART Multiplexer Supported Not applicable

Communication/Gateway DTMs

Supported Supported

The FDM RCI is installed in FDM Express Server.

Mux Monitoring Solution: This component, available with the full FDM product, is

not available with FDM Express.

FDM HART Multiplexer: This component, also available with the full FDM

product, is not available with FDM Express

Station Maintenance View: This option is only used with Experion for the full

FDM product. It is not available with FDM Express.

License information

An FDM Express license upgrade is a requirement for the software to function. The

Server Management Tool provides the functionality to manage the license for FDM.

Using the Licensing option, you can upgrade (install) the provided FDM Express license.

ATTENTION

After installing of FDM, ensure to upgrade FDM with the provided license.

1. Before You Begin

1.2. Installation components and requirements


REFERENCE - INTERNAL

For more information on upgrading license, refer to the Upgrading FDM license in the FDM User’s Guide.

Hardware and software requirements


Refer to EP03-480-430X, Field Device Manager Express Specifications, for information on hardware and software requirements.

FDM Express compatibility with Experion releases

FDM Express does not support connection with Experion R400. Only the full FDM

product supports this.


For more information, refer to the Release Notes document for FDM release.

1. Before You Begin

1.3. Installation Scenario


1.3 Installation Scenario

Overview

In FDM Express, the installed server handles the database required to the store device

information. The FDM Express server, along with FDM Remote Communication

Interface component, enables the FDM Express Client to access the required data from

devices connected via a MUX, modem or Comm DTM network.

FDM Express is installed in a Win 7 or Windows 2008 laptop or desktop computer for

use with locally available HART or PROFIBUS instruments.

Typical Architecture of FDM Express

The following diagram depicts the network architecture of FDM Express as used in the

maintenance shop.

Network architecture of FDM

The following components are installed during the FDM installation.

FDM Server, along with FDM Client and FDM RCI. When you select FDM Server

for installation, the FDM Client and FDM RCI are also selected by default.

FDM Express in Laptop PC

USB to RS 485 Converter

MUX Network &Devices

USB HART Modem

OR

HART Device


2. FDM Express Installation

ATTENTION

Manuals provided with FDM Express reflect the complete, full FDM product offering. Many documented options are not offered with FDM Express. The user should be aware of this.

This section covers the following topics which provide an overview of installation.

Topic Page

Installing FDM Express (laptop or desktop) 15

Installing FDM Client 22

ATTENTION

Ensure that your Antivirus solution is not configured to block copying of files or prevent installations from registering services.

To install FDM Express R430 successfully, the user must have administrative privileges.

2.1 Installing FDM Express

Prerequisites

The user should have FDM Express R430 DVD media ready.

The user must be a member of an Administrator group to install FDM Server.

Ensure you close all Windows applications before starting FDM Server software

Installation.

Ensure Windows Firewall / Internet Connection Sharing (ICS) service is running.


2.1. Installing FDM Express


To install FDM Server

Perform the following steps.

Step Action

1 Insert FDM Express software DVD into the DVD drive.

2 Right-click setup.exe and then click Run as administrator.

The Field Device Manager - InstallShield Wizard appears.

ATTENTION

You must close all the other applications before proceeding with the installation.

3 Click Next.

The License Information page appears.

4 Read the license agreement, and then:,

Click Yes, if you accept the terms.

Or

Click No, if you do not accept the terms.

When you click Yes, the Common Information page appears.

5 Read the common information, and then click Next. The Product Registration

page appears.

6 Type the name of the User.

7 Type the name of the Organization.

8 Click Next.




Step Action

The Module selection page appears.




Step Action

9 Select FDM Server component, and then click Next.

ATTENTION

When you select FDM Server option, FDM Client and Remote Communication Interface (RCI) are also selected.

If you are installing FDM Server on an unqualified operating system, the following message appears. Click OK to proceed with

the installation on an unqualified operating system.

The Enter User Account Information page appears.

FDM creates an internal user known as FDMMngr, which is used for authentication purposes. If the user does not exist, you need to enter new password to create the user.

10 Type the Password.




Step Action

ATTENTION

You should type the same password on any FDM computers, when prompted during installation.

The Password should contain a combination of alphabetic, numeric and special character(s).

It should have a minimum of eight characters in domain.

It cannot have any blank spaces.

The password should also conform with system password policy.

11 Retype the password in Confirm Password.

12 Click Next.

The User Group Information page appears.

The FDMMngr user account is created along with the following 4 default user groups.

FDM Administrators

FDM Engineers

FDM Operators and

FDM Supervisors

Note that the password for this group is not the same as the FDM login password.

In addition to the above groups, the installation creates another group called FDMAccessGroup which is used for providing permissions to Windows users

to enable communication across computers.

ATTENTION

An error message appears, if the FDMMngr account already exists on this computer and the password typed does not match with the existing FDMMngr password. In such a scenario, perform the following:

1. Choose Start > All Programs > Administrative Tools > Computer Management.

2. Expand Local Users and Groups > Users.

3. Right-click the User name and then click one of the following as necessary.

a) Set Password: If you want to change the password.

b) Delete: If you want to delete the user.




Step Action

13 Click Next.

ATTENTION

If the SQL Server 2008 is already installed, the Enter database information page appears.

1. Select Windows Authentication.

2. Click Validate and then click Next.

A Destination Folder page appears, displaying information about the default

destination folder.

If you want to change the default destination folder, click Browse to specify a

different destination folder.

14 Click Next.

A page appears, prompting you to verify the selected options and displaying the components selected for installation and the destination path.

Also, it displays the prerequisites which are to be installed as part of installation.

15 Click Install.

The setup starts installing all the prerequisites if they are not already installed.

ATTENTION

Both after installing Microsoft .Net framework 3.5 Service Pack1 and Microsoft SQL Server 2008, you are prompted to restart the computer. Click OK to continue. After the computer restarts, log on again as a

user with Administrator privileges.

The Setup Status page appears displaying installation status.

After the installation is complete, the Setup complete page appears.

16 Select Yes, I want to restart my computer now, if you want to restart the

computer.

Or

Select No, I will restart my computer later.

ATTENTION

It is recommended to always restart the computer immediately after the installation is complete.

After you restart the computer, you must first update the FDM License using CD. For more information, refer to section Updating the FDM license.




Step Action

17 Click Finish.


2.2. Installing FDM Client


2.2 Installing FDM Client FDM Server installation automatically installs the FDM Client on that computer.

Normally, this is all that would be required. You can also install FDM Client in separate

PCs that are networked to the FDM Express Server and log into the FDM Express Server

via any other Client. Separate Clients must be in PCs that are in the same Workgroup or

same Domain as the Server. With FDM Express, only one Client may be used at a time.

ATTENTION

Do not install the RCI component with Client, since FDM Express does not support the remote RCI node. Note there is no problem if the RCI is installed, but it cannot be used.

By default FDM Server, FDM Client, and Remote Communication Interface (RCI) are selected, you can clear FDM Server and Remote Communication Interface (RCI) option to install FDM Client.

Prerequisites

FDM R430 DVD media.

To install FDM Client

Perform the following steps.

Step Action

1 Insert FDM software DVD into the DVD drive.

2 Right-click setup.exe and then click Run as administrator.

The Field Device Manager - InstallShield Wizard appears.

ATTENTION

You must close all the other applications before proceeding with the installation.

3 Click Next.

The License Information page appears.

4 Read the license agreement, and then:,

Click Yes, if you accept the terms.

Or

Click No, if you do not accept the terms.




Step Action

When you click Yes, the Common Information page appears.

5 Read the common information, and then click Next. The Product Registration

page appears.

6 Type the name of the User.

7 Type the name of the Organization.

8 Click Next. The Module selection page appears.

9 Select the feature(s) that you want to install and click Next.


FDM creates an internal user known as FDMMngr, which is used for authentication purposes. If the user doest not exist, you need to enter new password to create the user.


ATTENTION

You should type the same password on any FDM computers, when prompted during installation.

The Password must contain a combination of alphabetic, numeric and special character(s).

It must have a minimum of eight characters in domain.

It must not have any blank spaces.

The password should also confirm with system password policy.





Step Action

12 Click Next.

The FDMMngr user account is created and a default user group is created as:

FDMAccessGroup: It is used for providing permissions to Windows users to enable communication across computers.

ATTENTION







A Destination folder page appears, displaying information about the default

destination folder.

If you want to change the default destination folder, click Browse to specify the

different destination folder.

13 Click Next.


Also it displays the prerequisites which are to be installed as part of installation.

14 Click Install.





Step Action

The Setup Status page appears displaying the installation status.

After the installation is complete, the Setup complete page appears.


computer.

Or


ATTENTION

It is recommended to always restart the computer immediately after the installation is complete.

16 Click Finish.


3. Post Installation Tasks This section describes the tasks that must be performed after FDM installation depending

on the configuration and set up.

3.1 Updating the FDM license

ATTENTION

FDM features are not enabled until you update (install) the required license.

Prerequisites

FDM R430 license file.

To update FDM License, perform the following steps.

Step Action

1 Insert media which contain the license file for FDM.

2 Copy the license file from the media to the local system.

3 Log on to FDM Server Management Tool.

For more information, refer to section Logging on to the FDM Server Management Tool in FDM User’s Guide.

ATTENTION

Ensure that the FDM Server is stopped.

3. Post Installation Tasks

3.1. Updating the FDM license


Step Action

4 Click the Licensing icon in the left pane of the window.

The list of features and the licensing details appears in the right pane.

The licensing information is listed with the following details:

Option indicates the name of the feature pertaining to the software.

Status refers to the present status of the license for a feature. It is Licensed or Not Licensed.

Value(s) specifies the number of licenses provided for each feature. For

some of the features, the values are license enabled or disabled.

5 Click Browse to select the license file. The Select a License File dialog box

appears.

6 Select the file and click Open.

The path for the license file (with the .xml extension) appears under Update License.

7 Click Update.

A confirmation message appears displaying license has been updated and click OK.

8 Click Exit to close FDM Server Management dialog box.


3.2. Executables required in DEP exception list


3.2 Executables required in DEP exception list The following executables must be added to the Data Execution Prevention exception

list, depending upon the FDM components you have selected during the installation. In

case you fail to do so, it may result in FDM components stopping to respond while using

DTMs.

On FDM Client and FDM Server node:

HCMClient.exe Default installation path: C:\Program

Files\Honeywell\FDM\ClientMachine\Bin\HCMClient.exe

Adding executables to Data Execution Prevention (DEP) execution list

To add the executables to Data Execution Prevention execution list, perform the

following steps.

Step Action

1 Choose Start > Control Panel. The Control Panel appears.

Click Classic view and double-click System.

Under Task, click Advanced system settings.

Or

Right-click Computer and click Properties.

The System Properties dialog box appears.

2 Click the Advanced tab.

3 Under Performance, click Settings.

The Performance Options dialog box appears.

4 Click the Data Execution Prevention tab.

5 In case Turn on DEP for essential Windows programs and services only

option is selected, then go to step 6.

Or,

In case, Turn on DEP for all programs and services except those I select option is selected, then click the Add button and select the executables

depending on the components you have selected.

6 Click Apply.

7 Click OK to close the Performance Options dialog box.

8 Click OK to close the System Properties dialog box.


3.3. Configuring the network information


Step Action

9 Restart the computer.

3.3 Configuring the network information After FDM installation and upgrading license is complete, you must configure networks

using Server Management Tool on FDM Server.

REFERENCE – INTERNAL

For more information about Configuring Networks, see FDM User’s Guide.

The only valid network types supported by FDM Express are:

RS-232 HART modem: FDM uses the RS-232 HART Modem to communicate

with HART devices using the serial port. A USB-to-RS-232 adaptor is required

for a laptop.

Honeywell HART DE modem: The Honeywell HART DE Modem provides the

network communication interface to HART devices. Again, aUSB-to-RS-232

adaptor is required.

RS-485 HART multiplexer: Using a USB-to-RS485 adaptor, FDM can

communicate to multiple HART devices in the field connected to HART

Multiplexers. A single HART Multiplexer network can support up to 31

multiplexers.

Comm DTM Interface: FDM supports communications to Profibus and HART-

over-Profibus devices using FDT/DTM technology.

See the FDM User’s Guide for more information about these different network types.

3.4 First logon You must provide valid user credentials to log on to FDM Client or FDM Server

Management Tool. FDM has a predefined user name Administrator.

When you launch FDM client, you can specify the server name to which the client must

connect to. For the first login, you must enter the server name. If FDM client connects to

the specified FDM server, then the server name is saved and it is available for selection

in the dropdown list during subsequent logins. After the connection to the server, enter

the following login details:

Login Name: administrator


3.4. First logon


Password: password

Domain Name: Classic Server Security

ATTENTION

It is recommended to log on to FDM Client and change this password after

the initial system configuration is complete.

REFERENCE – INTERNAL

For more information about user log on, see FDM User’s Guide.


4. FDM Maintenance

4.1 Overview The FDM installation supports the following using FDM Maintenance option.

Modify – Using this option you can add new component(s) or remove the currently

installed component(s).

Repair – Using this option you can reinstall the selected components installed by the

previous setup.

Remove – Using this option you can remove all the selected components.

Before starting FDM maintenance

Perform the following before proceeding with the FDM maintenance:

Log on to Server Management tool, and stop FDM Server.

On the FDM Server PC, choose Start > Control Panel > Administrative Tools >

Services and stop the FDM Remote Communication Interface service.

Ensure all SQL applications (like query analyzer and SQL Enterprise manager and

so on.) are closed.

Ensure all FDM application windows are closed.

4. FDM Maintenance

4.2. Modifying FDM components


4.2 Modifying FDM components Using this option, you can remove any currently installed component or install a new

component along with the currently installed component.

To modify FDM installation, perform the following steps.

Step Action

1 Choose Start > All Programs > Honeywell FDM > FDM Maintenance.

Or,

Choose Start > Control Panel > Programs and Features. Select Field Device Manager and click Change.

Or,

Insert FDM software DVD into the DVD drive.

2 Right-click setup.exe and click Run as administrator.

The FDM Maintenance page appears.

4. FDM Maintenance



Step Action

ATTENTION

You must close all other applications before you proceed.

3 Click Modify, and then click Next. The Add/Remove Features page appears.

4 Perform any one of the following to modify the installation, as necessary.

If you want to remove a feature, clear the check boxes corresponding to the already installed features.

Or,

If you want to add a feature, select the feature.

5 Click Next. The Enter User Account Information page appears.

FDM creates an internal user known as FDMMngr, which is used for authentication purposes. If the user does not exist, you need to enter new password to create the user.


ATTENTION

You must type the same password on all the computers, when prompted during installation.






8 Click Next.

4. FDM Maintenance



Step Action

ATTENTION

If FDM Server is selected during maintenance, the following message appears.

Click Yes to proceed with the maintenance.

If you select FDM Server, the User Group Information page appears.


FDM Administrators

FDM Engineers

FDM Operators and

FDM Supervisors

In addition to the above groups, the installation creates another group called FDMAccessGroup which is used for providing permissions to Windows users to

enable communication across computers.

If you select other features (FDM Client, FDM RCI, FDM HART Multiplexer, Station Maintenance View, or Mux Monitoring Solution), the FDMMngr user account is created and a default user group is created as:

FDMAccessGroup: Its is used for providing permissions to Windows users to enable communication across computers.

4. FDM Maintenance



Step Action

ATTENTION







9 Click Next.


Also it displays the prerequisites which are to be installed as part of installation.

10 Click Modify.


The Setup Status page appears displaying the maintenance status.

After modifying FDM components, the Maintenance Complete page appears.


computer.

Or


ATTENTION

It is recommended to always restart the computer immediately after the maintenance is complete.

12 Click Finish.

4. FDM Maintenance

4.3. Repairing FDM components


4.3 Repairing FDM components Using the Repair option you can reinstall all the components installed by the previous

setup.

To repair FDM Components, perform the following steps.

Step Action

1 Insert FDM software DVD into the DVD drive.

ATTENTION

Repair option is currently not supported through Add/remove programs or FDM Maintenance.

The following error message appears, if you try to repair through Add/remove programs or FDM Maintenance.

2 Right-click setup.exe and click Run as administrator.


ATTENTION

You must close all the other applications before proceeding with the maintenance.

4. FDM Maintenance



Step Action

3 Click Repair, and then click Next.


FDM creates an internal user known as FDMMngr, which is used for authentication purposes. If the user doest not exist, you need to enter new password to create the user.


ATTENTION

You must type the same password on all the computers, when prompted during installation.






4. FDM Maintenance



Step Action

6 Click Next.

ATTENTION

If FDM Server is selected during maintenance, the following message appears.

Click Yes to proceed with the maintenance.

If you are repairing FDM Server, the User Group Information page appears.


FDM Administrators

FDM Engineers

FDM Operators and

FDM Supervisors

In addition to the above groups, the installation creates another group called FDMAccessGroup which is used for providing permissions to Windows users to

enable communication across computers.

If you are repairing other features (FDM Client, FDM RCI, FDM HART Multiplexer, Station Maintenance View, or Mux Monitoring Solution), the FDMMngr user account is created and a default user group is created as:

FDMAccessGroup: It is used for providing permissions to Windows users to enable communication across computers.

ATTENTION




3. Right-click the User name and then click one of the following as

4. FDM Maintenance



Step Action

necessary.



7 Click Next.


8 Click Repair.

The Setup Status page appears displaying the maintenance status.

After repairing FDM components, the Maintenance Complete page appears.


computer.

Or


ATTENTION

It is recommended to always restart the computer immediately after the maintenance is complete.

10 Click Finish.

4. FDM Maintenance

4.4. Removing FDM


4.4 Removing FDM Using Remove option you can remove all the FDM components which are installed in

the system.

Before you remove FDM, refer to the section Before starting FDM maintenance.

ATTENTION

If SQL Server 2008 is installed along with FDM, when you remove the FDM Server, the SQL Server 2008 is also removed by default.

To Remove FDM components, perform the following steps.

Step Action

1 Choose Start > All Programs > Honeywell FDM > FDM Maintenance.

Or,

Choose Start > Control Panel > Programs and Features. Select Field Device Manager and click Uninstall.

Or,

Insert FDM software DVD into the DVD drive.


ATTENTION

You must close all the applications before proceeding with the removal of FDM.

2 Click Remove, and then click Next.

4. FDM Maintenance

4.4. Removing FDM


Step Action

A page appears displaying the components ready to be removed.

3 Click Remove.

The following message appears.

4 Click Yes.

The Setup Status page appears displaying the removal status.

After the removal of FDM is complete, the Maintenance Complete page

appears.


computer.

Or


ATTENTION

It is recommended to always restart the computer immediately after completely removing FDM software.

6 Click Finish.

4. FDM Maintenance

4.4. Removing FDM


Honeywell Process Solutions 1860 W. Rose Garden Lane Phoenix, AZ 85027 USA

field device manager express - honeywell · r430 field device manager express express software...

Documents