fe599 lever lock installation instructionshomeseer.com/pdfs/schlage/fe599 online is-b.pdf · fe599...
TRANSCRIPT
-
FE599 Lever Lock Installation Instructions
Keypad
Key
Cover
Coverscrews (2)
Baseplate
Latch
Strike
Latch/strikescrews (4) AA Batteries (4)
Lever
Pin wrench
OR
Alternate Faceplate
Important Information
Lock Programming Code
six (6) digits
User Code A
four (4) digits
User Code B
four (4) digits
Web Support: part2.schlage.com
Customer Service: (877) 288-7707
http://www.part2.schlage.com
-
1 Locate Programming Code and Preset User CodesThe programming code and the preset user codes are printed on the yellow stickers located on the back of the keypad and on the installation sheet that came in the box. Write these codes in the space provided on the first page.
OR O OU!
Without these user codes, you can get locked out.Si no cuenta con estos cdigos de usuario, es posible que no pueda abrir.Vous ne pouvez entrer sans dverrouiller l'aide des codes d'utilisateur.
Preset Codes
Cdigos preajustados
Prrglage des codes
Programming CodeCdigo de programacinCode de programmation
User CodesCdigos de usuarioCodes utilisateur
Lock ModelModelo de la cerraduraModle de serrure
Serial NumberNmero de serieNumro de srie
Alternate FaceplateChapa frontal alternaPlateau trous alternatif
2
Install LockInstalacin de la cerradura Installer le verrou1
ORO
OU
2
180
2 (70 mm)2 (60 mm)
Choose Faceplate to Match DoorEscoja la placa delantera para emparejar la puertaChoisir la ttire pour galer la porte
OR
O
OU
4
4
3
ORO
OU
4
5
!
6 Caution Precaucin Mise en garde
7
3
TopParte superiorHaut
TopParte superiorHaut
Match arrowsLas flechas deben quedar alineadasAligner les flches
2 (60 mm)OR O OU2 (70 mm)
2 (53 mm)HoleAgujeroTrou
5 (140 mm)Minimum
MnimoMinimum
(2)
Installation InstructionsInstrucciones de instalacinNotice d'installation
Check DimensionsRevise las dimensionesVrifier les dimensions
2Prog Code XXXXXXUser Code A XXXXUser Code B XXXX
(FCC ID: P2GXXXXX)XXXXXSN XXXXXXXXX
Prog C
ode XX
XX
XX
User C
ode A X
XX
XU
ser Code B
XX
XX (FC
C ID
: P2G
XX
XX
X)
XX
XX
XS
N X
XX
XX
XX
XX
Prog Code XXXXXXUser Code A XXXXUser Code B XXXX
(FCC ID: P2GXXXXX)XXXXXSN XXXXXXXXX
2C\, (60 mm)OR2C\v (60 mm)
2Z\, (53 mm)Hole
2 Check Door DimensionsIf your door does not match the dimensions shown, go to www.part2.schlage.com for instructions on how to prepare your door.
http://www.part2.schlage.com
-
3 Install Strike Into Frame
4 If Necessary, Change Latch FaceplateCheck edge of door to determine the type of faceplate required.
OR
-
5
OR
Door Jamb Door Jamb
6P5
15-8
04Re
v. 08
/07
" "
0
""(36 mm)
5 Install LatchLatch must be flipped so that bevel faces toward door jamb.
6 Remove Sticker from back of Lock
-
8 Adjust Hands-free PostThe hands-free post is the threaded stud on back of lock. Its purpose (in step 10) is to attach the lock and baseplate together so that the lock will hold itself on the door.
Hands free post may need to be adjusted with a screwdriver to the dimensions shown below.
Z\,- Z\v(3 mm - 6 mm)
Hold keypadagainst door
Adjust with screwdriver so screw extends beyond door edge.
7 Install the KeypadFeed the cable under latch assembly as shown below. Then slide the tailpiece through the hole as shown below.
Hands-freepost
-
9
10 Slide Baseplate onto Door over Hands-free postHands-free post should lock plate against door surface. If hands-free post does not lock plate onto door, see step 8 for adjustment.
Hands-free post
Feed Cable through BaseplateFeed the cable through the hole as shown below. DO NOT connect the cable at this point.
-
12 Install Batteries and Battery Cover
11 Connect the CableSnap the connectors together.
-
13 Install Cover and LeverSee step 14 on the next page to verify that the lever is handed correctly to match your door. If the lever does not snap into place easily, you may have to tap the lever with a hammer using a piece of wood to cushion it. Be careful not to damage the finish of the lever.
!Tuck wires into open space on baseplate.Be careful not to pinch any wires betweencover and baseplate.
-
Check Handing of Lever14
IncorrectSee steps below to
change lever handing
CorrectGo to step 15
To Change Lever Handing
a b
c
d
-
16
15
Test Outside Entry (When Door is Locked)When you press your User Code (four numbers) on the keypad, the door will unlock for 5 seconds, allowing entry.
Test Locking and Unlocking from the Interior
Green light(indicates unlocked)
Red light(indicates locked)
To Unlock, Press Button To Lock, Press Button
Programming Code XXXXXXUser Code A xxxxUser Code B xxxx
S/N x-xxxxxxxxModel BE369
Press (four numbers) Green flash = unlock
! Test with door open to avoid possibly being locked out!
Verify that latch retracts when lever is turned
on keypad
! Test with door open to avoid possibly being locked out!
Follow the directions on document to continue setup.
17 This portion of the setup is complete.
Document 2 is located at part2.schlage.com.
http://www.part2.schlage.com
-
2010 Schlage Lock CompanyFE599 Online IS Rev. 03/10-b
FCC NoticeThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this equipment not expressly approved by Schlage could void the users authority to operate the equipment.
FCC ID: P2GFE599 IC: 7954A-FE599
PATENT NOTICESchlage products and those of its subsidiary companies and licensees may be covered by both issued and pending U.S. and foreign patents, copyrights and trademarks. Manufactured items are covered by one or more of the following patents:
507071551525585308131539514455931935598726564086356831275715717
576541257694725809816581608658202905881590591891662863476297725
652337565333366540274658142668025466905773692631971434777159424
D372417D372854D406056D406528D426452D428324D450558D457048D457049
D458829D467155D472788D487388D520331D520332D537702D541620D543435