S A N D P I P E R P U M P . C O M

Warren Rupp, Inc. • A Unit of IDEX Corporation800 N. Main St., Mansfield, Ohio 44902 USA Telephone 419.524.8388 • Fax 419.522.7867

5 YEAR LIMITED PRODUCT WARRANTY 5 Year Guarantee for defects in material or workmanship. See sandpiperpump.com/content/warranty-certifications for complete warranty, including terms and conditions, limitations and exclusions.

F E AT U R E

EXCLUSIVE

USE ONLY GENUINE SANDPIPER PARTS All certification, standards, guarantees & warranties originally supplied with this pump will be invalidated by the use of service parts not identified as “Genuine SANDPIPER Parts.”

SUCTION / DISCHARGE PORT SIZE• 2” Sanitary Clamp

CAPACITY ELASTOMERIC AND TPE FITTED

• 0 to 71 gallons per minute (0 to 268 LPM)PTFE FITTED

• 0 to 65 gallons per minute (0 to 246 LPM)AIR DISTRIBUTION VALVE

• No-lube, no-stall designSOLIDS-HANDLING

• Up to .187 in. (4.76mm)

F15 METALLIC FOOD PROCESSING PUMP TECHNICAL DATA SHEET

PERFORMANCE

ISO 9001 Certified ISO 14001 Certified

FDA COMPLIANT PUMPSFor a variety of food processing, pharmaceutical and cosmetic industry applications

SERIES

HEADS UP TO• 110 psi or 254 ft. of water

(7.6 Kg/cm2 or 76 meters)MAXIMUM OPERATING PRESSURE

• 125 psi (8.6 bar)DISPLACEMENT/STROKE ELASTOMERIC AND TPE FITTED

• .25 Gallon / .95 literPTFE FITTED

• .31 Gallon / 1.17 literWEIGHTS

• Stainless Steel 57 lbs. (25.85kg)

II 2G EEx m c T5II 2D c IP65 T100°C

Disc

harg

e Hea

d in

PSI

0

140

120

100

80

60

40

20

0

Capacity in Liters Per Minute

Capacity in U.S. Gallons Per Minute

Displacement Per Stroke, 0.25 Gal. (0.95 L)

AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI

SCFM M3/HR 5 8.5 10 17 20 34 30 51 40 68 50 85 60 101.9

0 2010

5 1020 30

40

50

60

4030 50 60 70 80Meters Feet0 0

40

80

120

160

200

240

280

320

10

20

30

40

50

60

80

90

70

0

1

2

3

4

5

6

7

8

9

10

BAR

50 100 150 200 250 300

Disc

harg

e Hea

d in

PSI

0

140

120

100

80

60

40

20

0

Capacity in Liters Per Minute

Capacity in U.S. Gallons Per Minute

Displacement Per Stroke, 0.13 Gal. (0.49 L)

AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSI

SCFM M3/HR 10 17 20 34 30 51 40 68 50 85 60 101.9

0 2010

10 2030

4050

60

4030 50 60 70Meters Feet0 0

40

80

120

160

200

240

280

320

10

20

30

40

50

60

80

90

70

0

1

2

3

4

5

6

7

8

9

10

BAR

50 100 150 200 250

ELASTOMERIC AND TPE FITTEDPTFE FITTED

S A N D P I P E R P U M P . C O M

Warren Rupp, Inc. • A Unit of IDEX Corporation800 N. Main St., Mansfield, Ohio 44902 USA Telephone 419.524.8388 • Fax 419.522.7867

DIMENSIONS

Food Processing Metallic Dimensions in inches (mm dimensions in brackets). The dimensions on this drawing are for reference only. A certified drawing can be requested if physical dimensions are needed.

2.56

13.62

17.33

16.66[423.16]

[345.95]

[65.02]

[440.18]

[346.96]

[63.75]

[292.10]

[354.84]

[177.80]

[223.01]

[150.88]

[261.11]

[38.10]

[7.78]

[63.50]2"SUCTION SANITARY

CLAMP FLANGE

2"DISCHARGE SANITARYCLAMP FLANGE

1/2" NPTAIR INLET

13.66

11.50

2.51

.31

2.50

13.97

3/4" NPTAIR EXHAUST

7.00

8.78

5.94

10.28

1.50

R.22

NOTES:

1. THE DIMENSIONS ON THIS DRAWING ARE FOR REFERENCE ONLY. A CERTIFIED DRAWING CAN BE REQUESTED IF PHYSICAL DIMENSIONS ARE NEEDED.

BOTTOM VIEW

A UPDATED TO CURRENT DESIGN MAV 10/12/10 3309

REV REVISION CHG DATE ECN

THIS IS A PROPRIETARY DOCUMENT. DO NOT REPRODUCE OR DISCLOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF WARREN RUPP INC.

MADE FROM

WETTED END MATERIAL:

PART NUMBER

DESCRIPTION

DRAWING NUMBER

WARREN RUPP INC.

REV

A

DO NOT SCALE DRAWING

DIMENSIONS ARE INCHES

SHEET

C

678

A

8 7 6 5 4 3 2 1

D

B

D

C

B

A

E4SAxxxx0-FP

E4 CLAMPED FOOD PROCESSING PUMP

1 1of

E4SAxxxx0-FP

ELECTROPOLISHED STAINLESS

SEE BOM

ALL DIAPHRAGM TYPES ELASTOMERIC MATERIAL:

AIR END MATERIAL:NICKLE PLATED ALUMINUM

2.56

13.62

17.33

16.66[423.16]

[345.95]

[65.02]

[440.18]

[346.96]

[63.75]

[292.10]

[354.84]

[177.80]

[223.01]

[150.88]

[261.11]

[38.10]

[7.78]

[63.50]2"SUCTION SANITARY

CLAMP FLANGE

2"DISCHARGE SANITARYCLAMP FLANGE

1/2" NPTAIR INLET

13.66

11.50

2.51

.31

2.50

13.97

3/4" NPTAIR EXHAUST

7.00

8.78

5.94

10.28

1.50

R.22

NOTES:

1. THE DIMENSIONS ON THIS DRAWING ARE FOR REFERENCE ONLY. A CERTIFIED DRAWING CAN BE REQUESTED IF PHYSICAL DIMENSIONS ARE NEEDED.

BOTTOM VIEW

A UPDATED TO CURRENT DESIGN MAV 10/12/10 3309

REV REVISION CHG DATE ECN

THIS IS A PROPRIETARY DOCUMENT. DO NOT REPRODUCE OR DISCLOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF WARREN RUPP INC.

MADE FROM

WETTED END MATERIAL:

PART NUMBER

DESCRIPTION

DRAWING NUMBER

WARREN RUPP INC.

REV

A

DO NOT SCALE DRAWING

DIMENSIONS ARE INCHES

SHEET

C

678

A

8 7 6 5 4 3 2 1

D

B

D

C

B

A

E4SAxxxx0-FP

E4 CLAMPED FOOD PROCESSING PUMP

1 1of

E4SAxxxx0-FP

ELECTROPOLISHED STAINLESS

SEE BOM

ALL DIAPHRAGM TYPES ELASTOMERIC MATERIAL:

AIR END MATERIAL:NICKLE PLATED ALUMINUM

S A N D P I P E R P U M P . C O M

Warren Rupp, Inc. • A Unit of IDEX Corporation800 N. Main St., Mansfield, Ohio 44902 USA Telephone 419.524.8388 • Fax 419.522.7867

F XX X X X X X X X X X XXModel #:

F __ ____ __ __ __ __ __ __ __ __ __ ____(fill in from pump nameplate)

Your Model #:

Pump Pump Check Design Wetted Diaphragm/ CheckValve Non-Wetted Porting Pump Muffler Pump Config. Size Valve Level Material CheckValve Seat Material Options Style Options Options

Material Profile: Operating Temperatures:

Max. Min.

CONDUCTIVEACETAL: Tough, impact resistant, ductile. Good abrasion resistance and low friction surface. Generally inert, with good chemical resistance except for strong acids and oxidizing agents.

190°F88°C

-20°F-29°C

EPDM: Shows very good water and chemical resistance. Has poor resistance to oils and solvents, but is fair in ketones and alcohols.

280°F138°C

-40°F-40°C

FKM(FLUOROCARBON): Shows good resistance to a wide range of oils and solvents; especially all aliphatic, aromatic and halogenated hydrocarbons, acids, animal and vegetable oils. Hot water or hot aqueous solutions (over 70°F(21°C)) will attack FKM.

350°F177°C

-40°F-40°C

HYTREL®: Good on acids, bases, amines and glycols at room temperatures only.

220°F104°C

-20°F-29°C

NEOPRENE: All purpose. Resistance to vegetable oils. Gener-ally not affected by moderate chemicals, fats, greases and many oils and solvents. Generally attacked by strong oxidizing acids, ketones, esters and nitro hydrocarbons and chlorinated aromatic hydrocarbons.

200°F93°C

-10°F-23°C

NITRILE: General purpose, oil-resistant. Shows good solvent, oil, water and hydraulic fluid resistance. Should not be used with highly polar solvents like acetone and MEK, ozone, chlorinated hydrocarbons and nitro hydrocarbons.

190°F88°C

-10°F-23°C

NYLON: 6/6 High strength and toughness over a wide tem-perature range. Moderate to good resistance to fuels, oils and chemicals.

180°F82°C

32°F0°C

POLYPROPYLENE: A thermoplastic polymer. Moderate tensile and flex strength. Resists stong acids and alkali. Attacked by chlorine, fuming nitric acid and other strong oxidizing agents.

180°F82°C

32°F0°C

PVDF: (Polyvinylidene Fluoride) A durable fluoroplastic with excellent chemical resistance. Excellent for UV applications. High tensile strength and impact resistance.

250°F121°C

0°F-18°C

SANTOPRENE®: Injection molded thermoplastic elastomer with no fabric layer. Long mechanical flex life. Excellent abrasion resistance.

275°F135°C

-40°F-40°C

UHMWPE: A thermoplastic that is highly resistant to a broad range of chemicals. Exhibits outstanding abrasion and impact resistance, along with environmental stress-cracking resistance.

180°F82°C

-35°F-37°C

URETHANE: Shows good resistance to abrasives. Has poor resistance to most solvents and oils.

150°F66°C

32°F0°C

VIRGINPTFE: (PFA/TFE) Chemically inert, virtually impervious. Very few chemicals are known to chemically react with PTFE; molten alkali metals, turbulent liquid or gaseous fluorine and a few fluoro-chemicals such as chlorine trifluoride or oxygen difluoride which readily liberate free fluorine at elevated temperatures.

220°F104°C

-35°F-37°C

Maximum and Minimum Temperatures are the limits for which these materials can be operated. Temperatures coupled with pressure affect the longevity of diaphragm pump components. Maximum life should not be expected at the extreme limits of the temperature ranges.

Metals:ALLOYC: Equal to ASTM494 CW-12M-1 specification for nickel and nickel alloy.

STAINLESSSTEEL: Equal to or exceeding ASTM specification A743 CF-8M for corro-sion resistant iron chromium, iron chromium nickel and nickel based alloy castings for general applications. Commonly referred to as 316 Stainless Steel in the pump industry.

For specific applications, always consult the Chemical Resistance Chart.

CAUTION!Operatingtemperaturelimitationsareasfollows:

EXPLANATION OF PUMP NOMENCLATURE

PUMP BRAND F Food Processing

PUMP SIZE 15 1-1/2”

CHECK VALVE TYPE B Ball

DESIGN LEVEL 1 Design Level

WETTED MATERIAL S Stainless Steel

MATERIALS

DIAPHRAGM/CHECK VALVE MATERIALS D FDA Santoprene / PTFE H Hytrel/Hytrel K PTFE with FDA Hytrel Backer / PTFE Z One-Piece Bonded / PTFE

CHECK VALVE SEAT D FDA Santoprene H FDA Hytrel S Stainless Steel

NON-WETTED MATERIAL OPTIONS N Nickel Plated Aluminum

NOTE: See service manual for ATEX details.

SP_DS_TemplateDataSheet_0817

PORTING OPTIONS T 2” Sanitary Clamp

PUMP STYLE F Food

MUFFLER OPTIONS 6 Metal Muffler

PUMP OPTIONS 0 None

II 2G EEx m c T5II 2D c IP65 T100°C