ep.s3100 ep.n5100 ep.s3200 ep.n5200 ep.s3400 ep hah/entrypass/manual/hcb... · n5200, s3200, n5400...

EP.S3100 EP.N5100 EP.S3200 EP.N5200 EP.S3400 EP.N5400

Wiring Guide

Version 1.14 Last Updated: 14-03-2013

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

1

Note: N5100, N5200 and N5400 are network enabled controllers S3100, S3200 and S3400 are serial enabled controllers N5100 and S3100 have 4 inputs and 2 Outputs (2 Relays – Support 2 Doors, 2 Readers) N5200 and S3200 have 8 inputs and 4 outputs (4 Relays - Support 2 Doors, 2 Readers) N5400 and S3400 have 8 inputs and 4 outputs (4 Relays – Support 4 Doors, 4 Readers) N5200, S3200, N5400 and S3400 support unlimited access level Only firmware version 3.00.10.08 and above support features above N5100 and S3100 not support unlimited access level S3100, S3200, S3400, N5100, N5200 and N5400 support HID (AGK00, 09, 10, 11, 14, 19, 20), Wiegand Multi-Bit, Keyed Card + Pin Only firmware version 3.00.10.08 and above support features above N5100, N5200 and N5400 support AES Encryption Only firmware version 3.00.10.08 and above support AES Encryption S3200, S3400, N5200, N5400 support event trigger Only firmware version 3.00.10.08 and above support event trigger See http://www.entrypass.net/ for updates, revisions, and download the latest installation manual Platform1 version 3 support 6 and 10 digits format For existing site, P1 will detect its card database to determine 6 or 10 digits; For new site, user can change the digits as long as the card database is empty Please refer to separate EntryPass Platform1 User Manual for detail operation help. The Official EntryPass Platform1 User Manual can be downloaded from our website under “Download” section

Technical Support If you cannot find the answer to your question in this manual or in the Help files, we recommend you contact your system installer. Your installer is familiar with your system configuration and should be able to answer any of your questions. Should you need additional information, please call our Technical Support Help Desk, Monday to Friday 9:00 AM to 6:00 PM (GMT +8:00) Method Details Phone + 60 (3) - 8068 1929 Fax + 60 (3) - 8068 1922 Internet www.entrypass.net Email [email protected]

Before you begin…

2

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

mailto:[email protected]

CAUTION Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. To prevent a risk of explosion do not pry the battery out with a metal or conductive tool.

Considerations Prior to Installation

Preparing Your EntryPass Controllers EntryPass controller contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instruction below: •Observe precautions while handling the circuit board assembly by using proper grounding straps and handling precautions at all •Visually ensure no onboard parts is broken, damage or contains burn mark •Do not turn on the power supply until you completed all wiring and external add on devices installations

Instances of Non-Warranty •Damage due to natural disaster, accident or human cause. •Damage as a result of violating the conditions recommended in the user manual •Damage due to improper installation •Damage due to use of uncertified components •Damage due to use exceeding the permitted parameters

3

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Component Description

4

Relay 3 Relay 4 Supply Voltage Selector Relay LEDs

Supply Voltage Selector

Relay LEDs

Buzzer Relay 1 Relay 2 Buzzer ON/OFF

MCU Battery

Address Dip Switch

Cold Start Switch

Reset Switch

COM Rx/Tx LEDs

RS232 COMs

Heartbeat LED

RS485 COMs

Network Port

Cold Start, Factory Default and AES Hard reset Selection Jumper

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Legend Description

5

I1D0 I1D1 LED1 BUZ1 IN1 IN2 GND NC1 COM1 NO1 NC2 NO2COM2 VR1+ GND O1D0 O1D1 LED2 BUZ2 IN3 IN4 GND C3- C3+ C2- C2+ C1- C1+

Lower Connector

Reader 1 Input 1,2 Relay 1 Relay 212V/5V

Voltage

supply

Reader 2 Input 3,4RS485

Com3

RS485

Com2

RS485

Com1

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

O1D0 - Reader 2 Data 0 Input O1D1 - Reader 2 Data 1 Input LED2 - Reader 2 LED BUZ2 - Reader 2 Buzzer IN3 - Input 3 IN4 - Input 4 GND - Inputs Ground C3- - RS485 COM3 (-) Connection C3+ - RS485 COM3 (+) Connection C2- - RS485 COM2 (-) Connection C2+ - RS485 COM2 (+) Connection C1- - RS485 COM1 (-) Connection C1+ - RS485 COM1 (+) Connection

I1D0 - Reader 1 Data 0 Input I1D1 - Reader 1 Data 1 Input LED1 - Reader 1 LED BUZ1 - Reader 1 Buzzer IN1 - Input 1 (Default: Door Sensor) IN2 - Input 2 (Default: Exit Push Button) GND - Inputs Ground NC1 - Relay 1 Normally Close Connection COM1 - Relay 1 Common Input NO1 - Relay 1 Normally On Connection NC2 - Relay 2 Normally Close Connection COM2 - Relay 2 Common Input NO2 - Relay 2 Normally ON Connection VR1+ - Supply Voltage Positive Connection (12V/5V) GND - Supply Voltage Negative/Ground Connection

For VR1+ to supply 12V, please make sure JP6 is at 1-2 pins For VR1+ to supply 5V, please make sure JP6 is at 2-3 pins

Legend Description

6

I2D0 I2D1 LED3 BUZ3 IN5 IN6 GND NC3 COM3 NO3 NC4 NO4COM4 VR2+ GND O2D0 O2D1 LED4 BUZ4 IN7 IN8 IN9 GND

Upper Connector

Input 5, 6 Relay 3 Relay 4

12V/5V

Voltage

supply Input 7, 8Reader 3 Reader 4

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

I2D0 - Reader 3 Data 0 Input I2D1 - Reader 3 Data 1 Input LED3 - Reader 3 LED BUZ3 - Reader 3 Buzzer IN5 - Input 5 IN6 - Input 6 NC3 - Relay 3 Normally Close Connection COM3 - Relay 3 Common Input NO3 - Relay 3 Normally ON Connection NC4 - Relay 4 Normally Close Connection COM4 - Relay 4 Common Input NO4 - Relay 4 Normally ON Connection

VR2+ - Supply Voltage Positive Connection (12V/5V) GND - Supply Voltage Negative/Ground Connection O2D0 - Reader 4 Data 0 Input O2D1 - Reader 4 Data 1 Input LED4 - Reader 4 LED BUZ4 - Reader 4 Buzzer IN7 - Input 7 IN8 - Input 8 IN9 - Reserved GND - Inputs Ground

Upper connector only applicable to S3200, S3400, N5200 and N5400 Reader 3 and 4 only applicable to S3400 and N5400

For VR2+ to supply 12V, please make sure JP6 is at 1-2 pins For VR2+ to supply 5V, please make sure JP6 is at 2-3 pins

Legend Description

7

+12V - Power Supply Positive 12V DC -12V/GND - Power Supply Ground ETH - Power Supply Earthing ACC - AC Fail Monitoring BAT/BS - Backup Battery Monitoring

+12V-12V/

GND ETH ACCBAT/

BS

Power Supply Connector

BAT/BS (Backup Battery Monitoring) point will monitor the backup battery voltage which will supply power to the board when AC power is cut off.

The minimum voltage for cutoff while using backup battery is 8.4V

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Power Supply Unit Specification

8

Power Supply Unit Specification: • Switching Power Supply • 12V DC • 3 Amp (Minimum)

ENTRYPASS

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Connecting the Lock (Normally Closed - NC), Breakglass and Keyswitch

9

- +

NC1 COM1

Emergency

Breakglass

Emergency

Keyswitch

Electro-Magnetic Lock or Drop Bolt–+

Lower ConnectorI1D0 I1D1 LED1 BUZ1 IN1 IN2 GND NC1 COM1 NO1 NC2 NO2COM2 VR1+ GND O1D0 O1D1 LED2 BUZ2 IN3 IN4 GND C3- C3+ C2- C2+ C1- C1+

12V+

GNDPSU

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Diode(1N4002) must be installed at the locking devices in order to protect against back EMF It is advisable to connect EM lock COM to 12V+ of PSU (Power Supply Unit)

Connecting the Striker Lock or Drop Bolt (Normally Open - NO)

10

Diode(1N4002) must be installed at the locking devices in order to protect against back EMF

- +

NO

1

CO

M1

Striker Lock or Drop Bolt–+


12V+

GNDPSU

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

CO

M1

-+

NC

2

CO

M2

Emergency

Breakglass 1

Emergency

Keyswitch 1

Electro-Magnetic Lock 1


+-

-+

-+


NC

1

12V+

GND

PSU

Emergency

Breakglass 2Emergency

Keyswitch 2

Connecting the Locks (NC), Breakglasses and Keyswitches (2 Doors Mode Only)

11


Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

CO

M1

-+

NO

2

CO

M2

Striker Lock or Drop Bolt 1


+-

-+

-+


NO

1

12V+

GND

PSU

Connecting the Locks (NO) (2 Doors Mode Only)

12


Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Connecting the Locks (NC), Breakglasses and Keyswitches (4 Doors Mode Only)

13

CO

M3

-+

NC

4

CO

M4

Emergency

Breakglass 4

Emergency

Keyswitch 4


Emergency

Breakglass 3Emergency

Keyswitch 3


+-

-+

-+

NC

3

Upper ConnectionI2D0 I2D1 LED3 BUZ3 IN5 IN6 GND NC3 COM3 NO3 NC4 NO4COM4 VR2+ GND O2D0 O2D1 LED4 BUZ4 IN7 IN8 IN9 GND

12V+

GND

PSU

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Diode(1N4002) must be installed at the locking devices in order to protect against back EMF NC1 and NC2 connection for 4 Doors Mode please refer to 2 Doors Mode NC connection

4 Doors Mode only applicable for N5400 and S3400

Connecting the Locks (NO) (4 Doors Mode Only)

14

CO

M3

-+

NO

4

CO

M4



+-

-+

-+

NO

3


12V+

GND

PSU

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Diode(1N4002) must be installed at the locking devices in order to protect against back EMF NO1 and NO2 connection for 4 Doors Mode please refer to 2 Doors Mode NO connection

4 Doors Mode only applicable for N5400 and S3400

Connecting the Door Sensor and Door Release Button/Push Button

15

Push Button

IN1

IN2

GN

D

Door Sensor


Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

16

Connecting the Door Sensors and Door Release Buttons/Push Buttons (2 Doors Mode Only)

Push Button 1

IN1

IN2

GN

D

Door Sensor 1


IN3

IN4

GN

D

Push Button 2Door Sensor 2

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

17

Connecting the Door Sensors and Door Release Buttons/Push Buttons (4 Doors Mode Only)

IN5

IN6

GN

D



IN7

IN8

GN

D


Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

IN1,2,3,4 Connections for 4 Doors Mode please refer to 2 Doors Mode IN1,2,3,4 connections 4 Doors Mode only applicable for N5400 and S3400

Connecting the Readers – MiNi as Reader

18

To configure MINI as a READER Mode, press: •F1 •123456 •01 Enter •01 Enter •05 Enter •1 Enter •ESC x3

Re

ad

er

1

Re

ad

er

2



Re

ad

er

4

Re

ad

er

3

D0 - Orange D1 - Yellow

12V+ - Red

GND - Black

D0 - Orange D1 - Yellow

GND - Black

12V+ - Red

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Reader 3 and Reader 4 only applicable for N5400 and S3400

Connecting the Readers – 3rd Party Reader

19

Re

d (

VR

1+

)

Bla

ck (

GN

D)

Re

ad

er

1

Re

ad

er

2

I1D

0

I1D

1

LE

D1

BU

Z1

O1

D0

O1

D1

LE

D2

BU

Z2



Re

ad

er

3

Re

ad

er

4

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400


Connecting the Readers – Suprema Biometric Devices (BioLite Net)

20

Bio

Lite

Ne

t 2

Lower ConnectorI1D0 I1D1 LED1 BUZ1 IN1 IN2 GND NC1 COM1 NO1 NC2 NO2COM2 VR1+ GND O1D0 O1D1 LED2 BUZ2 IN3 IN4


Bio

Lite

Ne

t1B

ioL

ite

Ne

t 3

Bio

Lite

Ne

t 4

12V+ (Red)

GND (Black)

Wiegand GND (Black)

C3+ (Blue with White String)

C3- (Yellow with Black String)

12V+ (Red)

GND (Black)

Wiegand GND (Black)

C3+ (Blue with White String)

C3- (Yellow with Black String)

Da

ta1

(Wh

ite

)

Da

ta0

(Gre

en)

Da

ta1

(Wh

ite

)

Da

ta0

(Gre

en)

GND C3- C3+ C2- C2+ C1- C1+

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400


Connecting the Readers – Suprema Biometric Devices (BioEntry Plus)

21

Bio

En

try P

lus 2

Lower ConnectorI1D0 I1D1 LED1 BUZ1 IN1 IN2 GND NC1 COM1 NO1 NC2 NO2COM2 VR1+ GND O1D0 O1D1 LED2 BUZ2 IN3 IN4


Bio

En

try P

lus 1

Bio

En

try P

lus 3

Bio

En

try P

lus 4

12V+ (Red)

GND (Black)

C3+ (Blue)

C3- (Yellow)

12V+ (Red)

GND (Black)

Wiegand GND (Black)

C3+ (Blue)

C3- (Yellow)

Da

ta1

(Wh

ite

)

Da

ta0

(Gre

en)

Da

ta1

(Wh

ite

)

Da

ta0

(Gre

en)

GND C3- C3+ C2- C2+ C1- C1+

Wiegand GND (Black)

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400


Connecting to Another Controller for Cross-Board Interlock Purpose

22

Re

lay O

utp

ut

(NC

)

Re

lay O

utp

ut

(CO

M)

Re

lay O

utp

ut (N

C)

Re

lay O

utp

ut (C

OM

)

Inp

ut

(IN

)

Inp

ut (G

ND

)

Inp

ut (I

N)

Inp

ut (G

ND

)

Controller 1 Controller 2

Maximum 2 controllers can be connected each others for cross-board interlock purpose An interlock input and interlock relay need to be assigned using Platform1 for cross-board interlock on each controller Please configure the interlock input as ‘Open Trigger’ in Platform1 if interlock input is connected with NC relay output

Advisable to use analog input for detecting line open condition The cabling distance for cross-board interlock connection can up to 100 meter

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Connecting to the PC via Serial (RS-485)

23

….C

2-

C2

+

C2-

C2

+

C2-

C2

+

S3100 and S3200 (16)

Unit Address: 16

S3100 or S3200 (1)

Unit Address: 1

S3100 or S3200 (2)

Unit Address: 2

RS-485: 1000 meter (Maximum)

RS-232: 10 meter

EntryPass Platform1

Sserver Access Control System

PCC

(Communicator)

Rx

Tx

Po

we

r

RS

23

2

Serial connection (RS485) only applicable for maximum 16 sets S3100 or S3200 The serial address format in Platform1 is 255.255.255.X where X is unit address

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Connecting to the PC via Serial (RS-232)

24

S3100/S3200/S3400

Unit Address: 1

RS-232: 10 meter

EntryPass Platform1

Sserver Access Control System

1 2 3 4 5

6 7 8 9

JP4

Serial Port

DB9 Female

Connector

JP4

Serial connection (RS232) only applicable for a single S3100 or S3200 or S3400 The serial address format in Platform1 is 255.255.255.1

Connecting to the PC via Serial – Dip Switch Addressing Table

25

Switch 1 (1) Switch 2 (2) Switch 3 (4) Switch 4 (8) Switch 5 (16)

Address 01 ON OFF OFF OFF OFF

Address 02 OFF ON OFF OFF OFF

Address 03 ON ON OFF OFF OFF

Address 04 OFF OFF ON OFF OFF

Address 05 ON OFF ON OFF OFF

Address 06 OFF ON ON OFF OFF

Address 07 ON ON ON OFF OFF

Address 08 OFF OFF OFF ON OFF

Address 09 ON OFF OFF ON OFF

Address 10 OFF ON OFF ON OFF

Address 11 ON ON OFF ON OFF

Address 12 OFF OFF ON ON OFF

Address 13 ON OFF ON ON OFF

Address 14 OFF ON ON ON OFF

Address 15 ON ON ON ON OFF

Address 16 OFF OFF OFF OFF ON

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Each switch is represent by an address, the sum of the switch address will be the controller address The number in ( ) is the address of each individual switch of the dip switch

Example: To obtain Address 11, 1 + 2 + 8 = 11, So just switch on switch 1, 2, 4

Connecting to the PC via Network

26

….

N5100/N5200/N5400 (n)N5100/N5200/N5400 (1) N5100/N5200/N5400 (2)

EntryPass Platform1

Server Access Control System

….

Network Switch

Cat-5

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Network connection only applicable for N5100, N5200 and N5400 Factory default IP address for network controller is 192.168.1.100

Connecting to the Power Supply Unit

27

+12V

-12V

AC Fail (ACC)

Backup Battery Monitoring (BAT/BS)

Switching Mode

Power Supply Unit

(12V DV, 3A Minimum)

+12V

-12V

/

GN

DE

TH

AC

C

BA

T/

BS

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Performing Cold Start

28

Steps of performing cold start: 1. Please ensure that the jumper is inserted on JP1 1-2 2. Press and Hold COLD switch 3. Press RESET Switch and Release RESET switch 4. Release COLD switches when a long beeping sound heard

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

JP1Buzzer Jumper, JP2

Cold Start Initial Button, COLD

Reset Button, RESET

Advisable to perform cold start for the first time you turn on the power The buzzer will only beep if jumper is placed on (JP2) 1-2

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Performing Factory Default

29

Steps of performing Factory Default: 1. Please ensure that the jumper is inserted on JP1 7-8 2. Press and Hold COLD switch 3. Press RESET Switch and Release RESET switch 4. Release COLD switches when a long beeping sound heard

JP1Buzzer Jumper, JP2

Cold Start Initial Button, COLD

Reset Button, RESET

Factory Default will change the IP Address back to 192.168.1.100, Server IP to 192.168.1.254 and Port to 2020 For the network controller support AES Encryption feature, factory default will disable the AES feature

The buzzer will only beep if jumper is placed on (JP2) 1-2

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Performing AES Hard Reset

30

AES setting in the controller will be reset If the controller is connected with AES enabled Platfrom1, Platfrom1 will sync and update AES setting with the controller

Steps of performing AES Hard Reset: 1. Please ensure that the jumper is inserted on JP1 3-4 2. Press RESET Switch and Release RESET switch

JP1

Reset Button, RESET

Input Points Connection

31

Digital Input Connection By manufacturer default setting, IN1 is configured as Door Sensor and IN2 is configures as Push Button.

Analog/Supervised Input Connection A resistor of 3.6kΩ is required when user connect the device to the input connection.


Input 3,4Input 1,2

IN1/2/3/4

GND

IN1/2/3/4

GND

NC Analog

Device

3600 Ohm

Input default is digital The Inputs are configurable to digital or analog using Platform1

A resistor of 3600 ohm is required when using analog input This system is not support NO Analog device due to the architecture

Upper Connector

I2D0 I2D1 LED3 BUZ3 IN5 IN6 GND NC3 COM3 NO3 NC4 NO4COM4 VR2+ GND O2D0 O2D1 LED4 BUZ4 IN7 IN8 IN9 GND

Input 5,6 Input 7,8

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Rx

Tx

Power

RS232


Door SensorExit Button

PCC

Electro-magnetic Lock

Emergency

Breakglass

Emergency

Keyswitch

Entry Reader Exit Reader

Controller

Network Port

Fo

r Se

rial C

on

trolle

r On

ly

Fo

r Ne

two

rk C

on

trolle

r On

ly

Network

Switch

EntryPass

Platform1

Access Control Sytem

Power Supply Unit

ENTRYPASS

+12V -12V ETH ACC BAT

-+

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Complete Overview (In and Out Door Mode)

32

Serial Controller – S3100, S3200, S3400 Network Controller – N5100, N5200, N5400

Platform1 Profile: In and Out Readers

Complete Overview (2 Doors Mode)

33


Platform1 Profile: 2 Doors

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Rx

Tx

Power

RS232


Door Sensor 1Exit Button 1

Door Sensor 2Exit Button 2

PCC

EntryPass

Platform1


Electro-magnetic Lock 2

Electro-magnetic Lock 1

Emergency

Breakglass 1

Emergency

Keyswitch 1

Emergency

Breakglass 2

Power Supply Unit

Reader 1 Reader 2

Controller

Network

Port

Network

Switch

Fo

r Se

rial C

on

trolle

r On

ly

Fo

r Ne

two

rk C

on

trolle

r On

ly

ENTRYPASS


Emergency

Keyswitch 2

-+

-+

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Complete Overview (2x In and Out Doors Mode)

34

Platform1 Profile: 2x In and Out Doors

Serial Controller – S3400 Network Controller – N5400

Rx

Tx

Power

RS232

PCC

Controller

Network Port

Fo

r Se

rial C

on

trolle

r On

ly

Fo

r Ne

two

rk C

on

trolle

r On

ly

Network

Switch

EntryPass

Platform1




Power Supply Unit

ENTRYPASS

+12V

-12V

ET

HA

CC

BA

T

Reader 1 Reader 2

Reader 3 Reader 4

Door Sensor 1

&

Exit Button 1

Door Sensor 2

&

Exit Button 2

EM Lock 2

EM Lock 1

- +

-

+

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Complete Overview (4 Doors Mode)

35


Platform1 Profile: 4 Doors

Rx

Tx

Power

RS232

PCC

Controller

Network Port

Fo

r Se

rial C

on

trolle

r On

ly

Fo

r Ne

two

rk C

on

trolle

r On

ly

Network

Switch

EntryPass

Platform1




Power Supply Unit

ENTRYPASS

+12V

-12V

ET

HA

CC

BA

T

Reader 1 Reader 2

Reader 3 Reader 4

Door Sensor 1

&

Exit Button 1

Door Sensor 2

&

Exit Button 2

Door Sensor 3

&

Exit Button 3

Door Sensor 4

&

Exit Button 4

EM Lock 3

EM Lock 4

EM Lock 1

EM Lock 2

Complete Overview (In and Out Barriers)

36

Rx

Tx

Power

RS232


Entry Loop

Detector

Exit Loop

Detector

Entry Reader Exit Reader

PCC

Exit Barrier

Entry Barrier

Controller

Network

Port

Network

Switch

Fo

r Se

rial C

on

trolle

r On

ly

Fo

r Ne

two

rk C

on

trolle

r On

lyEntryPass

Platform1


Power Supply Unit

ENTRYPASS



Platform1 Profile: In and Out Barriers

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Complete Overview (2x In and Out Barriers)

37

Rx

Tx

Power

RS232

PCC

Controller

Network PortF

or S

eria

l Co

ntro

ller O

nly

Fo

r Ne

two

rk C

on

trolle

r On

ly

Network

Switch

EntryPass

Platform1




Power Supply Unit

ENTRYPASS

+12V

-12V

ET

HA

CC

BA

T

Entry Reader 1 Exit Reader 1


Entry Barrier 1 Exit Barrier 1

Entry Barrier 2 Exit Barrier 2

Entry Loop Detector 2 Exit Loop Detector 2

Entry Loop Detector 1 Exit Loop Detector 1


Platform1 Profile: 2x In and Out Barriers

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Exit Reader

Rx

Tx

Power

RS232


Entry Reader

PCC

Bidirectional

Turnstile

EntryPass

Platform1


Controller

Network

Port

Network

Switch

Fo

r Se

rial C

on

trolle

r On

ly

Fo

r Ne

two

rk C

on

trolle

r On

ly

Power Supply Unit

ENTRYPASS


IN

OUT

Complete Overview (In and Out Turnstiles Mode) – Bidirectional Turnstile


Platform1 Profile: In and Out Turnstile

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

38

Complete Overview ( 2 Turnstiles Mode)

39


Platform1 Profile: 2 Turnstile Mode

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Exit Reader

Rx

Tx

Power

RS232


Entry Reader

PCC

EntryPass

Platform1


Controller

Network

Port

Network

Switch

Fo

r Se

rial C

on

trolle

r On

ly

Fo

r Ne

two

rk C

on

trolle

r On

ly

Power Supply Unit

ENTRYPASS


INOUT

Complete Overview (2x In and Out Turnstiles Mode)

40

Rx

Tx

Power

RS232

PCC

Controller

Network Port

Fo

r Se

rial C

on

trolle

r On

ly

Fo

r Ne

two

rk C

on

trolle

r On

ly

Network

Switch

EntryPass

Platform1




Power Supply Unit

ENTRYPASS

+12V

-12V

ET

HA

CC

BA

T



Bidirectional

Turnstile 1

Bi-Directional

Turnstile 2


Platform1 Profile: 2 x In and Out Turnstiles

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Complete Overview (4 Turnstiles Mode)

41

Rx

Tx

Power

RS232

PCC

Controller

Network Port

Fo

r Se

rial C

on

trolle

r On

ly

Fo

r Ne

two

rk C

on

trolle

r On

ly

Network

Switch

EntryPass

Platform1




Power Supply Unit

ENTRYPASS

+12V

-12V

ET

HA

CC

BA

T

Reader 1 Reader 2

Reader 3 Reader 4

Turnstile 1 Turnstile 2

Turnstile 3 Turnstile 4


Platform1 Profile: 4 Turnstiles

Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

Cabling Information

Communication Data Signal Max Distance Description

PC to PCC RS232 10m

(30 ft) 22 AWG, 2 Pairs, Shielded

PCC to Serial Controller RS485 1000m

(3000 ft) 22 AWG, 2 Pairs, Shielded & Twisted Pair

Network Controller to PC or Network Switch

Network 100m

(300 ft) 24 AWG, 4 Pairs (Cat 5e)

Controller to Reader Wiegand 30m

(100 ft) 22 AWG, 2 Pairs, Shielded & Twisted Pair

Controller to Electro-Magnetic Lock

Power 30m

(100 ft) 18 AWG, 1 Pair

Controller to Push Button Contact 30m

(100 ft) 22 AWG, 1 Pair

Controller to Door Sensor Contact 30m

(100 ft) 22 AWG, 1 Pair

Controller to Controller for Cross-Board Interlock

Contact 100m

(300 ft) 22 AWG, 1 Pair

42


Model: EP.S3100, S3200, S3400, N5100, N5200, N5400

ep.s3100 ep.n5100 ep.s3200 ep.n5200 ep.s3400 ep hah/entrypass/manual/hcb... · n5200, s3200, n5400...

Documents