emulsions · •excellent resistance to water and alkalis. complies with the egyptian standard...

EMULSIONSWater Based Paints

DURASEAL SEALERLATEX SEALER 1800ACRYLIC PUTTYLATEX PUTTYFLEXI PUTTYHI KRAXDURACRIL 7000DURACRIL 6000DURACRIL 5000SI SHIELD MATTSI SHIELD TEXTURESHIELD TEXTURE

SI STONESI TONE 700SI TONE SILKBOND 2000HI TONE 2700S 7PRO COATFLEXI COATACRY STARELASTOSHIELDUNI MIX

DURASEAL SEALERPRODUCT DESCRIPTIONDURA SEAL is a high-quality sealer made of acrylic copolymer.

PRODUCT CHARACTERISTICS• Good whiteness and coverage.• Excellent resistance to water and alkalis.• Good penetration into surfaces, which provides excellent adhesive strength.• Excellent workability.Produced in compliance with the Ministerial Decree 181 Year 1996.

PROPOSED USESuits indoor and outdoor applications.

TYPE OF SURFACEConcrete, cementitious, and gypsum surfaces ..etc.

TECHNICAL SPECIFICATIONS Final Appearance Matt Viscosity 110 ± 5 Kreps (at 25°C temperature and 50% humidity) according to (ASTM D562-10 (2014)) Density 1.30 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 39 ± 2% FlashPoint NoninflammableVolatile Organic Compounds 43 gm/liter (according to Environmental Protection Agency – Method 24)

METHOD OF APPLICATION Diluent Water % Dilution (by volume) (25 – 30%) Application Tools Roller, brush, sprayer

INSTRUCTIONS FOR THE USE OF AIRLESS SPRAYER Pressure at nozzle 140 – 190 Kg/cm2 (2100 psi) Nozzle head 0.021 – 0.027 Spray angle 65° - 80° Filter Should be clean

FILM THICKNESS AND SPREADING RATEMin. Thickness Max. Thickness Average

Dry Film Thickness in Micron 30 40 35Non-Dry Film Thickness in Micron 76.92 102.56 89.74Theoretical Spreading Rate (m2/liter) 9 - 13 11.14

EMULSIONSWater Based Paints

PLEASE CONTACT SIPES OFFICE FOR ANY MORE INFORMATIONHEAD OFFICE: 104 EL-THAWRA ST. HELIOPOLIS, CAIRO, EGYPT.PHONE: +202 26905015 / FAX: +202 26905018 / Hotline: 19852 / Website: www.sipes.net

DURASEAL SEALER

DRYING TIMEGenerally,dryingtimedependsonairdraft,temperature,filmthickness,andnumberofcoats.Datainschedule is measured at 25°C temperature and 50% humidity:

Surface Drying 30 minutes (minimum)Re-coating 2 hours (minimum)

PROPOSED COATING SYSTEMAll surfaces (new and old) should be clean and free from dust, oil, fat, ..etc.

FOR NEW SURFACES • 1 coat Dura Seal

FOR OLD SURFACES• Clean the surface with water and suitable detergent. Make sure the surface is fully dry,then apply 1 coat Dura Seal.

CONDITIONS OF APPLICATIONTemperature of surface to be painted should not be lower than 10°C and 3°C above dew point. Appropriate air temperature and humidity should be observed.

GENERAL NOTES1. Actual spreading rate depends on many factors like surface condition, effectiveness of application tool, filmthickness,surfaceporosity,surfacedefects,temperature,quantitylostduringapplication..etc.2.Maximumspreadingrateforonecoatmayberealizedbyminimizingthedryfilmthickness,andviceversa.3. Paint should be mixed before use if it is made of different batches.

STORAGETwo years from production date, provided that proper storage conditions are observed. The product should be stored in compliance with storage instructions. The product should be stored in a cool well-ventilated environment, away from direct sun and heat. The container should be sealed tightly after use.

HEALTH AND SAFETYPlease read the protection instructions indicated on the container. Use in well-ventilated environment. Do not breathe or inhale mist. Avoid skin contact. Spillage on skin should be removed immediately with suitablecleanserandwater.Incaseofcontactwitheyes,flusheyeproperlywithabundantwaterandseek medical attention immediately. Keep away from the reach of children.

CLARIFICATIONThe information in thisTechnicalSpecification isgiven to thebestofour knowledge. It isbasedonlaboratory tests and practical experience. Sipes takes no responsibility for consequences of breaching the instructions. The Company reserves the right to change data herein without notice. Version: August September 2018, Sipes Co. This version supersedes prior versions.

LATEX SEALER 1800EMULSIONSWater Based PaintsPRODUCT DESCRIPTIONLATEX SEALER 1800 is a high-quality sealer made of vinyl acetate copolymer.

PRODUCT CHARACTERISTICS• Good penetration into surfaces and good adhesive strength.• Easy application.• Acceptable resistance to water and alkalis.• Good preparation for surfaces to receive the following coats.Produced in compliance with the Ministerial Decree 181 Year 1996.

PROPOSED USESuits indoor applications.

TYPE OF SURFACEConcrete, cementitious, and gypsum surfaces, ...etc.

TECHNICAL SPECIFICATIONS Final Appearance Matt Viscosity 105 ± 5 Kreps (at 25°C temperature and 50% humidity) according to (ASTM D562-10 (2014)) Density 1.27 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 28 ± 2% FlashPoint Noninflammable Volatile Organic Compounds 0.144 gm/liter (according to Environmental Protection Agency – Method 24)




Dry Film Thickness in Micron 30 40 35Non-Dry Film Thickness in Micron 107 142.86 125Theoretical Spreading Rate (m2/liter) 7- 9 8


LATEX SEALER 1800




FOR NEW SURFACES• 1 coat Latex Sealer 1800.

FOR OLD SURFACESClean the surface with water and suitable detergent. Make sure the surface is fully dry, then apply 1 coat Latex Sealer 1800.


GENERAL NOTES1. Actual spreading rate depends on many factors like surface condition, effectiveness of application tool, filmthickness,surfaceporosity,surfacedefects,temperature,quantitylostduringapplication..etc.2.Maximumspreadingrateforonecoatmayberealizedbyminimizingthedryfilmthickness,andviceversa.3. Paint should be mixed before use if it is made of different batches.



CLARIFICATIONThe information in thisTechnicalSpecification isgiven to thebestofour knowledge. It isbasedonlaboratory tests and practical experience. Sipes takes no responsibility for consequences of breaching the instructions. The Company reserves the right to change data herein without notice. Version: September 2018, Sipes Co. This version supersedes prior versions.

EMULSIONSWater Based Paints ACRYLIC PUTTYPRODUCT DESCRIPTIONACRYLIC PUTTY is a high-quality putty, made of water based polymer of high-quality acrylic.

PRODUCT CHARACTERISTICS• Good whiteness.• Suitable consistency and extreme ease of application.•Highabilitytofillporoussurfacesandrelativelysmallholes.• Good with sandability.• Excellent resistance to water and alkalis.Complies with the Egyptian Standard Specifications No. 6623/2008.

PROPOSED USESuits outdoor applications.

TYPE OF SURFACEConcrete, cementitious, and gypsum surfaces .. etc.

TECHNICAL SPECIFICATIONS Final Appearance Matt Strength 300 ± 10 gm/cm2 (at 25°C temperature and 50% humidity) Density 1.78 ± 0.03 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 55 ± 2% FlashPoint NoninflammableVolatile Organic Compounds 39 gm/liter (according to Environmental Protection Agency – Method 24)

METHOD OF APPLICATION Diluent Water % Dilution (by volume) as needed Application Tools Putty knife and steel Malg


Dry Film Thickness in Micron 184 275 229.5Non-Dry Film Thickness in Micron 334.5 500 417.25Theoretical Spreading Rate (m2/Kg) 2 - 3 2.4

DRYING TIMEGenerally,dryingtimedependsonair,temperature,filmthickness,andnumberofcoats.Datainscheduleis measured at 25°C temperature and 50% humidity:



ACRYLIC PUTTY


FOR NEW SURFACES• 1 coat Dura Seal• 2 – 3 coats Acrylic Putty (as needed)

FOR OLD SURFACESUse sandpaper, then clean the surface with water and suitable detergent. Make sure the surface is fully dry, then apply 1 or 2 coats of Acrylic Putty.


GENERAL NOTES1. Actual spreading rate depends on many factors like surface condition, effectiveness of application tool,filmthickness,surfaceporosity,surfacedefects,temperature,quantitylostduringapplication..etc.2.Maximumspreadingrateforonecoatmayberealizedbyminimizingthedryfilmthickness,andviceversa.3. Paint should be mixed before use if it is made of different batches.




EMULSIONSWater Based Paints LATEX PUTTYPRODUCT DESCRIPTIONLATEX PUTTY is a high-quality putty made of vinyl acetate copolymer and special additives. Produced to suit users needs.

PRODUCT CHARACTERISTICS• Excellent whiteness.• High consistency and ease of application.•Goodabilitytofillporoussurfacesandsmallholes..etc.• Excellent with sandability.• Provides very smooth layer.Complies with the Egyptian Standard Specifications No. 6623/2008.



TECHNICAL SPECIFICATIONS Final Appearance Matt Strength 260 ± 10 gm/cm2 (at 25°C temperature and 50% humidity) Density 1.8 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 52 ± 2% FlashPoint NoninflammableVolatile Organic Compounds 3 gm/liter (according to Environmental Protection Agency – Method 24)



Dry Film Thickness in Micron 95 140 117.5Non-Dry Film Thickness in Micron 182.69 269.23 225.96Theoretical Spreading Rate (m2/Kg) 2 - 3 2.46




LATEX PUTTY


FOR NEW CEMENTITIOUS SURFACES• 1 coat Latex Sealer 1800• 2 – 3 coats Latex Putty

FOR OLD SURFACESUse sandpaper, then clean the surface with water and suitable detergent. Make sure the surface is fully dry, then apply 1 or 2 coats of Latex Putty.






EMULSIONSWater Based Paints FLEXI PUTTYPRODUCT DESCRIPTIONFlexiPuttyisaputtymadeofacryliccopolymermodifiedwithhigh-qualityadditivestoprovidegoodperformance. Produced to suit users needs.

PRODUCT CHARACTERISTICS• Homogeneous consistency.• Extreme ease of application and workability.•Goodcharacteristicsoffillingporoussurfacesandsmallholes..etc.• Excellent with sandability.Complies with the Ministerial Decree No. 181/1996.



TECHNICAL SPECIFICATIONS Final Appearance Matt Strength 340 ± 10 gm/cm2 (at 25°C temperature and 50% humidity) Density 1.75 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 53 ± 2% FlashPoint Noninflammable Volatile Organic Compounds 18 gm/liter (according to Environmental Protection Agency – Method 24)



Dry Film Thickness in Micron 95 140 117.5Non-Dry Film Thickness in Micron 179.25 264.15 221.7Theoretical Spreading Rate (m2/Kg) 2 - 3 2.57


FLEXI PUTTY



PROPOSED COATING SYSTEMAll surfaces (new and old) should be clean and free from dust, oil, fat, ..etc.For New Cementitious Surfaces:• 1 coat Swift Sealer• 2 – 3 coats Flexi Putty

FOR OLD SURFACESUse sandpaper, then clean the surface with water and suitable detergent. Make sure the surface is fully dry, then apply 1 or 2 coats of Flexi Putty.






HI KRAXEMULSIONSWater Based PaintsPRODUCT DESCRIPTIONHi-Kraxisahigh-qualitycrackfillermadeofpureacrylicpolymerandhigh-performanceborosilicateadditives. Hi-Krax’s advanced formula provides the following characteristics:•Goodabilitytofillbigholesonasingleapplicationduetosmarttechnology.• Easy application.• Excellent adhesive strength.Produced in compliance with the Ministerial Decree No. 181 Year 1996.

PROPOSED USESuits indoor and outdoor applications.


TECHNICAL SPECIFICATIONS Final Appearance Matt Consistency Putty Density 0.42 ± 0.03 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 77 ± 2% FlashPoint NoninflammableVolatile Organic Compounds 3 gm/liter (according to Environmental Protection Agency – Method 24)

METHOD OF APPLICATION Diluent Water % Dilution (by volume) (as needed) Application Tools Putty knife

THEORETICAL SPREADING RATEIt depends on nature, depth, and dimensions of the crack. Maximum spreading rate for one coat may be realizedbyminimizingthedryfilmthickness,andviceversa.


HI KRAX



PROPOSED COATING SYSTEM• All cracks should be clean and free from dust, oil, fat, ..etc.• Use putty knife to force Hi-Krax into the crack to obtain a clean and smooth surface.• After 12 hours, apply the paint as usual.


GENERAL NOTES1. Actual spreading rate depends on many factors like surface condition, effectiveness of application tool,filmthickness,surfaceporosity,surfacedefects,temperature,quantitylostduringapplication..etc.2.Maximumspreadingrateforonecoatmayberealizedbyminimizingthedryfilmthickness,andviceversa.3. Paint should be mixed before use if it is made of different batches.4. Spreading rate for colors developed in coloring machines depends on selected colors.




DURACRIL 7000EMULSIONSWater Based PaintsPRODUCT DESCRIPTIONDuracril 7000 is a high-quality matt water based paint, made of best quality pure acrylic polymer. Available in white color and in a range of attractive colors that could be realized by using paint bases for coloring machines. Artistic characteristics of colors differ with selected colors.

PRODUCT CHARACTERISTICS• Attractive matt appearance. • Superior coverage and whiteness. • Extreme resistance to water, alkalis, and the liming phenomenon . • Ease of application • Excellent durability and high resistance to weather conditions. Complies with the Egyptian Standard Specifications No. 1539/2008.

PROPOSED USESuitsindoorandoutdoorapplications(forsomespecialcolorsonly),andasfinalcoatonneworoldsurfaces of high-relief texture.

TYPE OF SURFACEConcrete, cementitious, and gypsum surfaces.

TECHNICAL SPECIFICATIONS Final Appearance Matt Viscosity 125 ± 5 Kreps (at 25°C temperature and 50% humidity) according to (ASTM D562-10 (2014)) Density 1.37 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 39 ± 2% Washing Resistance More than 20000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint NoninflammableVolatile Organic Compounds 65 gm/liter (according to Environmental Protection Agency – Method 24)






DURACRIL 7000




FOR NEW SURFACES• 1 coat Latex Sealer 1800 / Dura Seal – indoor / outdoor• 2 – 3 coats Latex Putty / Acrylic Putty – indoor / outdoor• 1 coat Top Tone / S7 • 2 coats Duracril 7000

FOR OLD SURFACESRemove loose layers completely, then clean the surface with water and detergent. Make sure the surface is fully dry and soft then apply:• 1 coat Top Tone / S7 then 2 coats Duracril 7000.






DURACRIL 6000EMULSIONSWater Based PaintsPRODUCT DESCRIPTIONDuracril 6000 is a high-quality semi-glossy water based paint, made of best quality pure acrylic polymer. Available in white color and in a range of attractive colors that could be realized by using paint bases for coloring machines. Artistic characteristics of colors differ with selected colors.

PRODUCT CHARACTERISTICS• Semi-glossy with superior ability to retain gloss• Good whiteness and high coverage • Extreme resistance to water, alkalis, and the chalking •Easeandflexibilityofapplication •ExcellentdurabilityandhighresistancetoweatherconditionsComplies with the Egyptian Standard Specifications No. 1539/2008.

PROPOSED USE Suitsindoorandoutdoorapplications(forsomespecialcolorsonly),andasfinalcoat on new or old surfaces of high-relief texture.

TYPE OF SURFACE Concrete, cementitious, and gypsum surfaces.

TECHNICAL SPECIFICATIONS Final Appearance Semi-glossy Viscosity 125 ± 5 Kreps (at 25°C temperature and 50% humidity) according to (ASTM D562-10 (2014)) Density 1.38 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 42 ± 2% Washing Resistance More than 20000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint Noninflammable Volatile Organic Compounds 60 gm/liter (according to Environmental Protection Agency – Method 24)

METHOD OF APPLICATION Diluent Water % Dilution (by volume) (20 – 25%) Application Tools Roller, brush, airless sprayer



Dry Film Thickness in Micron 30 40 35Non-Dry Film Thickness in Micron 71.43 95.24 83.33Theoretical Spreading Rate (m2/liter) 10 - 14 12


DURACRIL 6000

DRYING TIMEGenerally,dryingtimedependsonairdraft,temperature,filmthickness,selectedcolors,andnumberofcoats. Data in schedule is measured at 25°C temperature and 50% humidity:


PROPOSED COATING SYSTEMAll surfaces (new and old) should be clean and free from dust, oil, fat, ..etc.For New Surfaces:• 1 coat Latex Sealer 1800 / Dura Seal – indoor / outdoor• 2 – 3 coats Latex Putty / Acrylic Putty – indoor / outdoor• 1 coat Top Tone / S7• 2 coats Duracril 6000

FOR OLD SURFACES COATED WITH WATER PAINTRemove loose layers completely, then clean the surface with water and detergent. Make sure the surface is fully dry and soft then apply:• 1 coat Top Tone / S7 then 2 coats Duracril 6000.






DURACRIL 5000EMULSIONSWater Based PaintsPRODUCT DESCRIPTIONDURACRIL 5000 is a high quality glossy water based paint, made of pure acrylic polymer. Available in white color.

PRODUCT CHARACTERISTICS• High gloss • Superior ability to retain gloss• Good whiteness and high coverage • Extreme resistance to water and alkalis• High adhesiveness • Excellent durability and high resistance to weather conditionsComplies with the Egyptian Standard Specifications No. 1539/2008.

PROPOSED USESuitsindoorandoutdoorapplications,andasfinalcoatonneworoldsurfacesofhigh-relieftexture.


TECHNICAL SPECIFICATIONS Final Appearance Glossy Viscosity 125 ± 5 Kreps (at 25°C temperature and 50% humidity) according to (ASTM D562-10 (2014)) Density 1.20 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 33 ± 2% Washing Resistance More than 20000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint Noninflammable Volatile Organic Compounds 55 gm/liter (according to Environmental Protection Agency – Method 24)






DURACRIL 5000




FOR NEW SURFACES• 1 coat Latex Sealer 1800 / Dura Seal – indoor / outdoor• 2 – 3 coats Latex Putty / Acrylic Putty – indoor / outdoor• 1 coat Top Tone / S7 • 2 coats Duracril 5000

FOR OLD SURFACES COATED WITH WATER PAINTRemove loose layers completely, then clean the surface with water and detergent. Make sure the surface is fully dry and soft then apply:• 1 coat Top Tone / S7 then 2 coats Duracril 5000.

CONDITIONS OF APPLICATIONTemperature of surface to be painted should not be lower than 10°C and 3°C above dew point. Appropriate air temperature and humidity should be observed.General Notes:1. Actual spreading rate depends on many factors like surface condition, effectiveness of application tool,filmthickness,surfaceporosity,surfacedefects,temperature,quantitylostduringapplication..etc.2.Maximumspreadingrateforonecoatmayberealizedbyminimizingthedryfilmthickness,andviceversa.3. Paint should be mixed before use if it is made of different batches.




SI SHIELD MATTEMULSIONSWater Based PaintsPRODUCT DESCRIPTIONSi Shield Matt is a matt water based paint, made of best quality pure acrylic polymer to provide excellent performance in outdoor surfaces and facades. Available in white color and in a range of other colors by using coloring machines. Artistic characteristics of colors differ with selected colors.

PRODUCT CHARACTERISTICS• Excellent resistance to dust due to the advanced technology adopted therein.•Highflexibility.Itworksasabridgetoconcealfinecracks.• Excellent resistance to ultra-violet radiations, variable temperatures, and pollution.• Excellent barrier against Chloride Ions; and protects against concrete liming phenomenon.• Extreme resistance to water, alkalis, and other outdoor conditions. Complies with the Egyptian Standard Specifications No. 1539/2008.

PROPOSED USE Suits outdoor applications (for some special colors only) on concrete, cementitious, andgypsumsurfaces,andasfinalcoatonneworoldsurfacesofhigh-relieftexture.


TECHNICAL SPECIFICATIONS Final Appearance Matt Viscosity 120 ± 5 Kreps (at 25°C temperature and 50% humidity) for white color, according to (ASTM D562-10 (2014)) Density 1.35 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) for white color, according to (ASTM D1475-13) % Solids by Volume 39 ± 2% (for white color) Washing Resistance More than 20000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint Noninflammable Volatile Organic Compounds 81 gm/liter (according to Environmental Protection Agency – Method 24)






SI SHIELD MATT


Surface Drying for white color 30 minutes (minimum)Re-coating for white color 4 hours (minimum)


FOR NEW SURFACES• 1 coat Dura Seal sealer / Latex Sealer 1800 (according to surface conditions)• 1 – 2 coats Acrylic Putty (as needed) • 1 coat Top Tone • 2 coats Si Shield Matt

FOR OLD SURFACES•Usesandpaperfirst,thencleanthesurfacewithwaterandsuitabledetergent.Makesurethesurfaceisfully dry then follow the above application steps.






SI SHIELD TEXTUREEMULSIONSWater Based PaintsPRODUCT DESCRIPTIONSI-Shield Texture is a Pure Acrylic Polymer based Texture emulsion paint that offers excellent performance for the exteriors and facade. Available in White color .Special colors can be made upon request. Thanks to its technologically advanced formulation, it can render the following features:

• Very attractive variety of texture can be obtained using different application tools.• Excellent Dirt Pick-up Resistance due to its unique state-of-the art technology.•Goodflexibilityandelasticitythatallowsbridgingofhairlinecracksandcrevice.•SignificantresistancetoUVrays,temperaturechangesandpollution.• Good barrier to chloride ions and protect against concrete carbonation.•Superiorresistancetowater,alkali,efflorescenceandotherexternalelements.•GoodfillingpropertiesandCoverssurfaceimperfection.Produced in compliance with the Ministerial Decree No. 181 Year 1996.

PROPOSED USE Suits outdoor applications on concrete, cementitious, and gypsum surfaces, and asfinalcoatonneworoldsurfacesofhigh-relieftexture.


TECHNICAL SPECIFICATIONS Finish Matt Texture Gel Strength 110±10 gm./cm² (at 25°C and RH 50%) for white color Density 1.38±0.05 gm./cm³ (at 25°C and RH 50%) for white color (ASTM D 1475-13) % Solids by Volume 46±2 % for white color Flash Point Non FlammableVolatile Organic Compounds 66 gm./L (as per EPA Method 24)

METHOD OF APPLICATION Diluent Water Application Tools Roller (cotton - sponge - shaping rollers)


Dry Film Thickness in Micron 65 80 72.5Non-Dry Film Thickness in Micron 141.3 174 157.6Theoretical Spreading Rate (m2/liter) 5 - 7 6.34


SI SHIELD TEXTURE

THEORETICAL COVERAGE5-7 m² /Kg./coat for white color (The actual coverage depends on various factors like nature of substrate, application method, thickness applied coat …etc., Also max spread rate per coat is obtained atminimumdryfilmthicknessandviceversa.

DRYING TIMEDrying time is generally related to air circulation, temperature, film thickness, selected colors andnumber of coats. Figures given in the table are testing at 25°C and 50% RH:Dry to Handle (for white color) Minimum 30 MinutesDry to Recoat (for white color) Minimum 4 Hours

RECOMMENDED SYSTEM OF APPLICATIONAll the new and old substrates should be cleaned properly to make them free from dirt, Grease. Oil, wax, etc.For new substrates:• Application of 1 coat of DURASEAL or LATEX SEALER 1800 (As per wall conditions).• Application of 1-2 coats ACRYLIC PUTTY (Only, if required).• Application of 1 coat of TOP-TONE / S7.• Application of 2 coat of SI-SHIELD TEXTURE.For old substrates:After complete removal of loosely held materials, wash the substrate thoroughly with detergent and water. And apply the following after ensuring that the substrate is dried well and smooth.

STORAGE2 years from date of production if kept closed and stored as suggested.The product must be stored in accordance with national regulations. The product must be kept in cool well-ventilated place, protected from sunlight and heat. Containers must be kept tightly closed after partial usage.

HEALTH AND SAFETYPlease observe the precautionary notice displayed on the container.Use under well ventilated conditions. Don’t breath or inhale mist. Avoid skin contact. Spillage on the skin shouldimmediatelyberemovedwithsuitablecleaner,soapandwater.Eyesshouldbewellflushedwithwater and medical attention to be sought immediately. Keep away from children.

DISCLAIMERThis information in this data sheet is given according to the best of our knowledge on laboratory testing and practical experience. SIPES will not be held responsible for results arising out when applied against specified.Wereservetherighttochangethegivendatawithoutnotice.

SHIELD TEXTUREEMULSIONSWater Based PaintsPRODUCT DESCRIPTIONSHIELD TEXTURE is a high-relief texture water based paint, made of styrene acrylic copolymer to provide excellent performance in outdoor surfaces and facades. Available in white color and may be colorized to a range of other colors as needed.

PRODUCT CHARACTERISTICS• Attain extremely attractive decorative assorted shapes by using different application tools.• Excellent resistance to dust due to the advanced technology adopted therein.•Highflexibility.Itworksasabridgetoconcealfinecracks.• Excellent resistance to ultra-violet radiations, variable temperatures, and pollution.• Excellent barrier against Chloride Ions; and protects against chalking.• Extreme resistance to water, alkalis, and other outdoor conditions.•Goodfillingproperties.Concealssurfacedefects.Produced in compliance with the Ministerial Decree 181 Year 1996.

PROPOSED USESuitsoutdoorapplicationsandasfinalcoatonneworoldsurfacesofhigh-relieftexture.


TECHNICAL SPECIFICATIONS Final Appearance Matt with high-relief texture Strength 110 ± 10 gm/cm2 (at 25°C temperature and 50% humidity) for white color Density 1.43 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) for white color, according to (ASTM D1475-13) % Solids by Volume 50 ± 2% for white color FlashPoint Noninflammable Volatile Organic Compounds 87 gm/liter (according to Environmental Protection Agency – Method 24)

METHOD OF APPLICATION Diluent Water % Dilution (by volume) (as needed for the required shape Application Tools Roller (cotton, sponge, shaping rollers)


Dry Film Thickness in Micron 125 150 137.5Non-Dry Film Thickness in Micron 250 300 275Theoretical Spreading Rate (m2/liter) 2 - 3 2.54


SHIELD TEXTURE




FOR NEW SURFACES• 1 coat Dura Seal sealer or Latex Sealer 1800 (according to surface conditions)• 2 coats Acrylic Putty (as needed) • 1 coat Top Tone / S7 • 2 coats Shield Texture

FOR OLD SURFACESRemove loose layers completely, then clean the surface with water and detergent. Make sure the surface is fully dry and soft then apply:• 2 coats Shield Texture






EMULSIONSWater Based Paints SI STONEPRODUCT DESCRIPTIONSi Stone is a unique sandy decorative water-based paint made of high quality water-based acrylic polymer. Si Stone is available in white color. It could be custom-colored in a wide range of colors.

PRODUCT CHARACTERISTICS• Obtain extremely attractive assorted decorative forms by using different application tools.• Coarse sand provides good level of hardness.• Fills gaps and conceals defects in walls.• Excellent tolerance to outdoor environmental conditions.Produced in compliance with the Ministerial Decree 181 Year 1996.

PROPOSED USESuits outdoor applications.


TECHNICAL SPECIFICATIONS Final Appearance Matt with high-relief texture Strength 180 ± 10 gm/cm2 (at 25°C temperature and 50% humidity) for white color Density 1.86 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) for white color, according to (ASTM D1475-13) % Solids by Volume 68 ± 2% for white color FlashPoint Noninflammable Volatile Organic Compounds 41 gm/liter (according to Environmental Protection Agency – Method 24)

METHOD OF APPLICATION Diluent Water % Dilution (by volume) (as required, dependant on desired shape) Application Tools Roller (cotton, sponge), shaping rollers, and special tools to obtain decorative effect.


Dry Film Thickness in Micron 150 250 200Non-Dry Film Thickness in Micron 220.59 367.64 294.11Theoretical Spreading Rate (m2/liter) 1.5 - 2.5 1.83


SI STONE


Surface Drying for white color 60 minutes (minimum)Re-coating for white color 5-6 hours (minimum)

PROPOSED COATING SYSTEMAll surfaces (new and old) should be clean and free from dust, oil, fat ..etc.

FOR NEW SURFACES• 1 coat of Dura Seal.•1–2coatsofSiStone(incasetwocoatsareapplied,dilutethefirstcoat).

FOR OLD SURFACES• After sandpapering, clean the surface properly with suitable detergent and water. Let dry, then follow the above steps for application.






SI TONE 700EMULSIONSWater Based PaintsPRODUCT DESCRIPTIONSi-Tone 700 is a high-quality matt water based paint, made of vinyl acetate copolymer and excellent additives. Available in white color and in a range of attractive colors that could be realized by using paint bases for coloring machines. Artistic characteristics of colors differ with selected colors.

PRODUCT CHARACTERISTICS• Superior coverage • High shine • Extreme resistance to water and alkalis• Good resistance for the chalking • Durability and long-term endurance Complies with the Egyptian Standard Specifications No. 1539/2008.

PROPOSED USESuits indoor and outdoor applications (according to type of colorant), yet it suits indoor surfaces more.

TYPE OF SURFACE Concrete, cementitious, and gypsum surfaces ..etc.

TECHNICAL SPECIFICATIONS Final Appearance Matt Viscosity 103 ± 5 Kreps (at 25°C temperature and 50% humidity) for white color, according to (ASTM D562-10 (2014)) Density 1.44 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) for white color, according to (ASTM D1475-13) % Solids by Volume 37 ± 2% Washing Resistance More than 10000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint Noninflammable Volatile Organic Compounds 16 gm/liter (according to Environmental Protection Agency – Method 24)






SI TONE 700




FOR NEW SURFACES• 1 coat Latex Sealer 1800 • 2 – 3 coats Latex Putty • 1 coat Top Tone or S7 • 2 coats Si-Tone 700

FOR OLD SURFACES WITH WATER BASED PAINTRemove loose layers completely, then clean the surface with water and detergent. Use Latex Putty on cracked and peeled spots. Make sure the surface is fully dry and soft then apply:• 2 coats Si-Tone 700.






SI TONE SILKEMULSIONSWater Based PaintsPRODUCT DESCRIPTIONSi-Tone Silk is a high quality silk-glossy smooth paint made of acrylic copolymer and excellent additives. Available in white color and in a range of other colors that could be realized by using paint primers for coloring machines. Artistic characteristics of colors differ with selected colors.

PRODUCT CHARACTERISTICS• Excellent resistance to water and alkalis • High resistance to stains• Superior ability to retain gloss • Easy application • Durability and long term endurance Complies with the Egyptian Standard Specifications No. 1539/2008.

PROPOSED USE Suits indoor and outdoor applications.

TYPE OF SURFACEConcrete, cementitious, and gypsum surfaces ..etc., whether new or previously painted.

TECHNICAL SPECIFICATIONS Final Appearance Silk-glossy Viscosity 105 ± 5 Kreps (at 25°C temperature and 50% humidity) for white color, according to (ASTM D562-10 (2014)) Density 1.3 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) for white color, according to (ASTM D1475-13) % Solids by Volume 39 ± 2% (for white color) Washing Resistance More than 12000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint NoninflammableVolatile Organic Compounds 25 gm/liter (according to Environmental Protection Agency – Method 24)






SI TONE SILK




FOR NEW SURFACES• 1 coat Latex Sealer 1800 • 2 – 3 coats Latex Putty • 1 coat Top Tone / Hi-Tone 2700 / Si-Tone 700 • 2 coats Si-Tone Silk

FOR PAINTED OLD SURFACESRemove loose layers completely, then clean the surface with water and detergent. Make sure the surface is fully dry and soft then apply:• 1 coat Top Tone / Hi-Tone 2700 / Si-Tone 700 • 2 coats Si-Tone Silk






BOND 2000EMULSIONSWater Based PaintsPRODUCT DESCRIPTIONBond 2000 is a high quality semi-glossy water based acrylic paint made of styrene acrylic copolymer. Available in white color and in a range of other colors that could be realized by using paint bases for coloring machines. Artistic characteristics of colors differ with selected colors.

PRODUCT CHARACTERISTICS• Semi-glossy appearance and superior ability to retain gloss• Good coverage and high glitter • Excellent resistance to water and alkalis• Good resistance to chalking • Durability and good resistance to weather conditions Complies with the Egyptian Standard Specifications No. 1539/2008.

PROPOSED USEThe white color suits indoor and outdoor applications. Use of other colors depends on selected colors (suits indoor walls more).

TYPE OF SURFACE Concrete, cementitious, and gypsum walls and ceilings ..etc.

TECHNICAL SPECIFICATIONS Final Appearance Semi-glossy Viscosity 115 ± 5 Kreps (at 25°C temperature and 50% humidity) for white color, according to (ASTM D562-10 (2014)) Density 1.27 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) for white color, according to (ASTM D1475-13) % Solids by Volume 42 ± 2% (for white color) Washing Resistance More than 15000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint NoninflammableVolatile Organic Compounds 28 gm/liter (according to Environmental Protection Agency – Method 24)






BOND 2000




FOR NEW SURFACES• 1 coat Latex Sealer 1800 • 2 – 3 coats Latex Putty • 1 coat Top Tone / S7 • 2 coats Bond 2000

FOR OLD SURFACESRemove loose layers completely, then clean the surface with water and detergent. Make sure the surface is fully dry and soft then apply:• 1 coat Top Tone / S7 then 2 coats Bond 2000






HI TONE EMULSIONSWater Based PaintsPRODUCT DESCRIPTIONHi-Tone 2700 is a high-quality matt water based paint, made of vinyl acetate copolymer and special additives. Available in white color and in a range of other colors that could be realized by using paint primers for coloring machines. Artistic characteristics of colors differ with selected colors.

PRODUCT CHARACTERISTICS• Good coverage and good brightness • Good resistance to water and alkalis• Good resistance for the chalking • Easy application• Washable • Durability and long-term enduranceComplies with the Egyptian Standard Specifications No. 1539/2008.

PROPOSED USE Suits indoor applications.

TYPE OF SURFACE Concrete, cementitious, and gypsum walls and ceilings, whether new or previously painted.

TECHNICAL SPECIFICATIONS Final Appearance Matt Viscosity 103 ± 5 Kreps (at 25°C temperature and 50% humidity) for white color, according to (ASTM D562-10 (2014)) Density 1.40 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) for white color, according to (ASTM D1475-13) % Solids by Volume 35 ± 2% Washing Resistance More than 10000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint NoninflammableVolatile Organic Compounds 15 gm/liter (according to Environmental Protection Agency – Method 24)




Dry Film Thickness in Micron 30 40 35Non-Dry Film Thickness in Micron 85.71 114.29 100Theoretical Spreading Rate (m2/liter) 8 - 11 10

HI TONE




FOR NEW SURFACES1 coat Latex Sealer 1800 • 2 - 3 coats Latex Putty 2 coats Hi-Tone 2700

FOR OLD SURFACESRemove loose layers completely, then clean the surface with water and detergent. Make sure the surface is fully dry and soft then apply:• 2 coats Hi-Tone 2700.







S7EMULSIONSWater Based PaintsPRODUCT DESCRIPTIONS7isanattractivemattemulsionpaintbasedonmodifiedAcryliccopolymertogiveafterapplicationasmoothfinishandgoodcolorappearance.

PRODUCT CHARACTERISTICS• High hiding power and Excellent Brightness. • High resistance to water and alkali.• High Adhesion Power • Low smellComplies with the Egyptian Standard Specifications No. 1539/2008.

PROPOSED USESuitable for Interior surfaces.

TYPE OF SURFACEConcrete, Cement, Gypsum Board, Plaster, etc.

TECHNICAL SPECIFICATIONS Final Appearance Matt Viscosity 137 ± 3 Kreps (at 25°C temperature and 50% humidity) for white color, according to (ASTM D562-10 (2014)) Density 1.67 ± 0.03 gm/cm3 (at 25°C temperature and 50% humidity) for white color, according to (ASTM D1475-13) % Solids by Volume 48 ± 2% (for white color) Washing Resistance More than 5000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint NoninflammableVolatile Organic Compounds 17 gm/liter (according to Environmental Protection Agency – Method 24)




Dry Film Thickness in Micron 40 55 45Non-Dry Film Thickness in Micron 83 114 94Theoretical Spreading Rate (m2/liter) 9 - 12 10.57

S7




FOR NEW SURFACES• Apply of 1 coat of Latex Sealer 1800. • Apply of 2-3 coats of Latex Putty.• Apply of 2 coats of S7

FOR OLD SURFACESRemove loose layers completely, then clean the surface with water and detergent. Make sure the surface is fully dry and soft. Use Latex Putty on areas where you have small cracks or peelings after the removal of loose old paint then apply: • 2 Coats of S7







PRO COATEMULSIONSWater Based PaintsPRODUCT DESCRIPTIONPro Coat is a matt water based paint, made of strong Styrene Acrylic Copolymer.

PRODUCT CHARACTERISTICS• Good whiteness and high coverage • Extreme resistance to water and alkalis • Easy to apply Complies with the Egyptian Standard Specifications No. 1539/2008.



TECHNICAL SPECIFICATIONS Final Appearance Matt Viscosity 140 ± 5 Kreps (at 25°C temperature and 50% humidity) according to (ASTM D562-10 (2014)) Density 1.56 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 42 ± 2% Washing Resistance More than 5000 washing cycles, in accordance with the EgyptianStandardSpecificationsNo.(1539/2008) FlashPoint NoninflammableVolatile Organic Compounds 22 gm/liter (according to Environmental Protection Agency – Method 24)






PRO COAT




FOR NEW SURFACES• 1 coat Swift Sealer • 2 – 3 coats Swift Putty • 2 coats Pro Coat

FOR OLD SURFACES:Remove loose layers completely, then clean the surface with water and detergent. Make sure the surface is fully dry and soft then apply:• 2 coats Pro Coat.

CONDITIONS OF APPLICATIONTemperature of surface to be painted should not be lower than 10°C and 3°C above dew point. Appropriate air temperature and humidity should be observed.General Notes:1. Actual spreading rate depends on many factors like surface condition, effectiveness of application tool,filmthickness,surfaceporosity,surfacedefects,temperature,quantitylostduringapplication..etc.2.Maximumspreadingrateforonecoatmayberealizedbyminimizingthedryfilmthickness,andviceversa.3. Paint should be mixed before use if it is made of different batches.




FLEXI COATEMULSIONSWater Based PaintsPRODUCT DESCRIPTIONFlexy Coat is a smooth matt paint, made of strong styrene acrylic copolymer. It provides acceptable quality at reasonable price.

PRODUCT CHARACTERISTICS• Superior coverage and whiteness • Dilutable with more water• Suits economy applications • Best choice for painting of ceilingsComplies with the Ministerial Decree 181/1996.


TYPE OF SURFACE Concrete, cementitious, and gypsum walls and ceilings.

TECHNICAL SPECIFICATIONS Final Appearance Matt Viscosity 135 ± 5 Kreps (at 25°C temperature and 50% humidity) according to (ASTM D562-10 (2014)) Density 1.68 ± 0.05 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 41 ± 2% FlashPoint NoninflammableVolatile Organic Compounds 13 gm/liter (according to Environmental Protection Agency – Method 24)




Dry Film Thickness in Micron 30 40 35Non-Dry Film Thickness in Micron 73 97.6 85.4Theoretical Spreading Rate (m2/kg) 6 - 8 7


FLEXI COAT




FOR NEW SURFACES• 1 coat Swift Sealer • 2 – 3 coats Swift Putty • 2 coats Flexy Coat

FOR OLD SURFACES WITH WATER BASED PAINTClean the surface properly with water and suitable detergent. Make sure the surface is fully dry, then apply 2 coats Flexy Coat.






EMULSIONSWater Based Paints ACRY STARPRODUCT DESCRIPTIONThe silk-glossy Acry Star is made of high quality styrene acrylic copolymer. It may be applied for paints of special effects, like Sipes Star and matt water-based paints ..etc., to provide a smooth silk-glossy coat and protection against water, stain, and airborne dust.Produced in compliance with the Ministerial Decree 181 Year 1996.

PROPOSED USESuits recently painted indoor surfaces.

TECHNICAL SPECIFICATIONS Final Appearance Silk texture Viscosity 95 ± 5 Kreps (at 25°C temperature and 50% humidity) according to (ASTM D562-10 (2014)) Density 1.00 ± 0.03 gm/cm3 (at 25°C temperature and 50% humidity) according to (ASTM D1475-13) % Solids by Volume 20 ± 2% FlashPoint NoninflammableVolatile Organic Compounds 37 gm/liter (according to Environmental Protection Agency – Method 24)

METHOD OF APPLICATION Diluent Water % Dilution (by volume) (10 – 15%) Application Tools Preferably roller and brush.


Dry Film Thickness in Micron 25 30 27.5Non-Dry Film Thickness in Micron 125 150 137.5Theoretical Spreading Rate (m2/liter) 6 - 8 7.27


Surface Drying 1 hour


ACRY STAR

PROPOSED COATING SYSTEMAll surfaces (new and old) should be clean and free from dust, oil, fat ..etc.

FOR NEW SURFACES•1coatAcryStarabovefinalcoat.

FOR OLD SURFACESClean the surface with water and suitable detergent. Make sure the surface is fully dry, then apply:•1coatAcryStarabovefinalcoat.






EMULSIONSWater Based Paints ELASTOSHIELDPRODUCT DESCRIPTIONElasto Shield is a high-quality silk-glossy water based paint of high flexibility,made of pure acrylicpolymer and carefully selected raw materials to provide best performance on outdoor surfaces, and uniquely attractive decorative shapes when applied thickly. Available in white color and in a range of other colors as needed.

PRODUCT CHARACTERISTICS• High resistance to dirt due to its unique design•

emulsions · •excellent resistance to water and alkalis. complies with the egyptian standard...

Documents