mkelectric.co.uk
LIGH
TING
CON
TROL
S
534
Connection Diagram
Operating Mode Selector Switch
Slave Connection Terminals
Example1: Multiple control buttons:
L
TTT1
TT
T2TT TT TT
T3
TTExample 2: Wiring for Multiple Master Dimmers with common Central-ON and Central-OFF
L
N
T T TT
T1 T2 T3 L N T1 T2 T3 L N
MASTER DIMMER 1 MASTER DIMMER 2
Load Load
T1 = Separate Dimming control for each master T2 = Central-ON for both master dimmers T3 = Central-OFF for both master dimmers
Standards and approvalsAll High Power Dimmer modules comply with EN 60669-2-1
TECHNICAL SPECIFICATION
ELECTRICAL
MAINS SUPPLY220-240V / 50Hz 220V / 60 Hz
TYPE OF LOADSFused GLS Tungsten filament lamps. Dimmable wirewound or electronic low voltage transformers of good quality. Inductive loads (i.e. conventional wire-wound transformers, etc.) must not be connected to the trailing edge dimmers.
Warning: These dimmer modules are not suitable for use with fl uorescent lamps or energy saving lamps.
PHYSICAL
AMBIENT OPERATING TEMPERATURE-5°C to +40°C
REDUCTION OF THE DIMMER POWER
If this product is used in an ambient temperature exceeding 40ºC, the maximum allowable load will need to be reduced according to the table below. This will prevent the internal thermal protection in the product from activating and switching the load off.
-10 0 10 20 30 40 50 60 70 80 90 1000
200400600800
1000
Ambient temperature in °C
Maximum Rated Load (W)
DescriptionThese dimmer modules are designed for mounting into distribution and consumer units containing 35mm Din rail according to EN50022. All master and slave dimmers must be connected to the same supply phase. Key points to observe during installation:
� The mains supply to the dimmer(s) must be protected by a suitable fuse or MCB rated no greater than 16A
� Do not exceed maximum control line length of 100m and do not run slave control lines parallel to mains and network cables
� Always observe the transformers recommended loading guidelines
� Load transformers at or close to their full rated capacity. Do not connect a small load to a larger transformers, (e.g. a 35W lamp on a 600VA transformer)
� Ensure that slaves are wired to the correct control terminals and that the polarity is observed
Note: The outputs of the K1402M and K1402S trailing edge dimmers may be connected in parallel to drive a single load greater than 1kW/900VA.
L
N
T1 T2 T3
0-10
VGn
d
L N
Gnd
0-10
V
Control input0...10V
Button inputT1 - T3
Mains connection220-240V~ / 50Hz
220V~ / 60Hz
Load
Switch
MASTER DIMMER
Control Wiring for operating Modes 1-6 (K1400) and Modes 1-7 (K1401/K1402)Control switches T1-3 should be push-to-make momentary contact switches.
Up to 10 operating switches may be wired in parallel with Neon indicators being allowed on control line T1 only.
Control Wiring for operating Mode 7 (K1400) and Mode 8 (K1401/K1402)Control switches T1 should be a standard single pole light switch with dimming via the rotary 0/1-10V potentiometer connected between 0-10V and Gnd on the Master dimmer.
High Power DimmerTechnical
WIR
ING
DE
VIC
ES
Technical Hotline +44 (0)1268 563720
LIGHTING CONTROLS
535
For a full range of corresponding products,
see pages 208-210 in the product selector.
K1400M
Page 2
INSTALLATION:
The dimmer module is designed for mounting into distribution and consumer units containing 35 mm DIN rail according to EN50022.
Please observe the following points during installation:● All master and slave dimmers must be connected to the same supply
phase.● The mains supply to the dimmer(s) must be protected by a suitable fuse
or MCB rated no greater than 16A● Do not exceed maximum control line length of 100m and do not run slave control lines parallel to mains and network cables.● Always observe the transformers recommended loading guidelines.● Load transformers at or close to their full rated capacity. Do not connect
a small load to a larger transformers, (e.g. a 35W lamp on a 600VA transformer)
● Ensure that slaves are wired to the correct control terminals and that the polarity is observed
Vorsicht! ErhöhteStrahlung
Vorsicht! Kontamination Vorsicht! Kontamination Vorsicht, Gefahr durchAbquetschen
Vorsicht, Gefahr durchAbschneiden
Vorsicht, Gefahr durchAbstürzen
Vorsicht, Gefahr durchätzende Stoffe
Vorsicht, Gefahr durchelektrischen Strom
Vorsicht, Gefahr durchelektrischen Strom
Vorsicht, Gefahr durchelektromagnetischeStrahlung
Vorsicht, Gefahr durchexplosionsgefährlicheStoffe
Vorsicht, Gefahr durchfeuergefährliche Stoffe
Vorsicht, Gefahr durchgiftige Stoffe
Vorsicht, Gefahr durchheiße Oberfläche
Vorsicht, Gefahr durchLaserstrahlung
Vorsicht, Gefahr durchRadioaktivität
Vorsicht, Gefahr durchRutschen
Vorsicht, Gefahr durchStolpern
Vorsicht, Gefahr durchVerwickeln
Vorsicht, Warnung voreiner Gefahrstelle
Vorsichtig verschieben!- veraltet -
Während derSchweißarbeiten,Arbeitsstelle beobachten
Wandbrände nicht vonoben löschen
Wandbrände von untennach oben löschen
Wandhydrant Wandhydrant (2.Vorschlag)
Wandhydrant, mit Angabedes Anschlusses
Wareneingang -Freigegeben
Wareneingang - Gesperrt Wärmeabzugseinrichtung
Important: Always use the same type of load on each dimmer module. Do not combine different load types to the same dimmer
Control Wiring for operating Modes 1-6:Control switches T1-3 for operating modes 1-6 should be push-to-make momentary contact switches.Up to 10 operating switches may be wired in parallel with Neon indicators being allowed on control line T1 only
Example1: Multiple control buttons:
L
T
T1
T
T2
T T T
T3
T
Example 2: Wiring for Multiple Master Dimmers with common Central-ON and Central-OFF
L
N
T T TT
T1 T2 T3 L N T1 T2 T3 L N
MASTER DIMMER 1 MASTER DIMMER 2
Load Load
T1 = Separate Dimming control for each master T2 = Central-ON for both master dimmers T3 = Central-OFF for both master dimmers
Control Wiring for operating Mode 7:Control switch T1 for operating mode 7 should be a standard single pole light switch with dimming via the rotary 0/1-10V potentiometer connected between 0-10V and Gnd on the Master dimmer
L
N
T1 T2 T3
0-1
0V
Gnd
L N
Gnd
0-1
0V
Control input 0...10V
Button inputT1 - T3
Mains connection220-240V~ / 50Hz
220V~ / 60Hz
Load
Switch
MASTER DIMMER
L N
F
K1401M1kW Leading Edge Dimmer - MasterFor use with K1401S and K1402S slave modules
®
R, L
ε 220/240V~50/60Hz
IEC60669-2-1
50061977-00160-1000VA 50-900VA
S1 S2 S3
L N
0-10V
0-10V
Gnd
Gnd T1 T2 T3
Mode1
537
8 2
6 4
K14001kW Universal Dimmer - Master/SlaveFor use with K1400 units configured as slaves
R, L, C
ε 220-240V~ / 50Hz220V~ / 60 Hz
EN 60669-2-1
50061976-00160-1000VA 50-900VA
P1 P2 ® ®
F
F
K1401M1kW Leading Edge Dimmer - MasterFor use with K1401S and K1402S slave modules
®
R, L
ε 220/240V~50/60Hz
IEC60669-2-1
50061977-00160-1000VA 50-900VA
S1 S2 S3
L N
0-10V
0-10V
Gnd
Gnd T1 T2 T3
Mode1
537
8 2
6 4
K14001kW Universal Dimmer - Master/SlaveFor use with K1400 units configured as slaves
R, L, C
ε 220-240V~ / 50Hz220V~ / 60 Hz
EN 60669-2-1
50061976-00160-1000VA 50-900VA
P1 P2 ® ®
F
220-240V~ / 50Hz220V~ / 60Hz
To additional SlaveDimmer Modules
Control connection (S1-S3)slave dimmer
Master-dimmer operating mode 1-7
To additional SlaveDimmer Modules
Control connection (S1-S3)slave dimmerOperating mode 8
Page 2
INSTALLATION:
The dimmer module is designed for mounting into distribution and consumer units containing 35 mm DIN rail according to EN50022.
Please observe the following points during installation:● All master and slave dimmers must be connected to the same supply
phase.● The mains supply to the dimmer(s) must be protected by a suitable fuse
or MCB rated no greater than 16A● Do not exceed maximum control line length of 100m and do not run slave control lines parallel to mains and network cables.● Always observe the transformers recommended loading guidelines.● Load transformers at or close to their full rated capacity. Do not connect
a small load to a larger transformers, (e.g. a 35W lamp on a 600VA transformer)
● Ensure that slaves are wired to the correct control terminals and that the polarity is observed
Vorsicht! ErhöhteStrahlung
Vorsicht! Kontamination Vorsicht! Kontamination Vorsicht, Gefahr durchAbquetschen
Vorsicht, Gefahr durchAbschneiden
Vorsicht, Gefahr durchAbstürzen
Vorsicht, Gefahr durchätzende Stoffe
Vorsicht, Gefahr durchelektrischen Strom
Vorsicht, Gefahr durchelektrischen Strom
Vorsicht, Gefahr durchelektromagnetischeStrahlung
Vorsicht, Gefahr durchexplosionsgefährlicheStoffe
Vorsicht, Gefahr durchfeuergefährliche Stoffe
Vorsicht, Gefahr durchgiftige Stoffe
Vorsicht, Gefahr durchheiße Oberfläche
Vorsicht, Gefahr durchLaserstrahlung
Vorsicht, Gefahr durchRadioaktivität
Vorsicht, Gefahr durchRutschen
Vorsicht, Gefahr durchStolpern
Vorsicht, Gefahr durchVerwickeln
Vorsicht, Warnung voreiner Gefahrstelle
Vorsichtig verschieben!- veraltet -
Während derSchweißarbeiten,Arbeitsstelle beobachten
Wandbrände nicht vonoben löschen
Wandbrände von untennach oben löschen
Wandhydrant Wandhydrant (2.Vorschlag)
Wandhydrant, mit Angabedes Anschlusses
Wareneingang -Freigegeben
Wareneingang - Gesperrt Wärmeabzugseinrichtung
Important: Electronic transformers may only be used if they are approved by the manufacturer for leading edge dimming.
Control Wiring for operating Modes 1-7:Control switches T1-3 for operating modes 1-7 should be push-to-make momentary contact switches. Up to 10 operating switches may be wired in parallel with Neon indicators being allowed on control line T1 only
Example1: Multiple control buttons:
L
T
T1
T
T2
T T T
T3
T
Example 2: Wiring for Multiple Master Dimmers with common Central-ON and Central-OFF
L
N
T T TT
T1 T2 T3 L N T1 T2 T3 L N
MASTER DIMMER 1 MASTER DIMMER 2
Load Load
T1 = Separate Dimming control for each master T2 = Central-ON for both master dimmers T3 = Central-OFF for both master dimmers
Control Wiring for operating Mode 8:Control switch T1 for operating mode 8 should be a standard single pole light switch with dimming via the rotary 0/1-10V potentiometer connected between 0-10V and Gnd on the Master dimmer
L
N
T1 T2 T3
+12
V
0-1
0V
Gnd
SE
L N
Control input0...10V
Button inputT1 - T3
Mains connection220-240V~ / 50Hz
220V~ / 60Hz
LoadSwitch
Load
Switch
MASTER DIMMER
L N
+12V
0-10V
Gnd SE T1 T2 T3
Mode1
537
8 2
6 4
T5A H250V~
A1 B1 A2 B2 Slave-Out
R,L R,C
K1401M1kW Leading Edge Dimmer - MasterFor use with K1401S and K1402S slaves modules
R, L
60-1000VA 50-900VA
P1 P2 ® ®
EN 60669-2-1
50061977-001
ε 220-240V~ / 50Hz220V~ / 60 Hz
F
L N
T5A H250V~
IN Out
IN Out
Slave
A AB B
K1401S1kW Leading Edge Dimmer - SlaveFor use with K1401M and K1402M master modules
R, L
60-1000VA 50-900VA
® ®
EN 60669-2-1
50061978-001
ε 220-240V~ / 50Hz220V~ / 60 Hz
F
L N IN Out
IN Out
Slave
A AB B
K1402S1kW Trailing Edge Dimmer - SlaveFor use with K1401M and K1402M master modules
R, C
® ®
60-1000VA 50-900VA
EN 60669-2-1
50061980-001
ε 220-240V~ / 50Hz220V~ / 60 Hz
F
L N
F
F
F
220-240V~ / 50Hz220V~ / 60Hz
Con
trol c
onne
ctio
n (A
,B)
slav
e di
mm
er
Master-dimmer operating Mode 1 – 8
K1401M
High Power Dimmer Technical
WIR
ING
DE
VIC
ES
mkelectric.co.uk
536
K1402M
Page 2
INSTALLATION:
The dimmer module is designed for mounting into distribution and consumer units containing 35 mm DIN rail according to EN50022.
Please observe the following points during installation:● All master and slave dimmers must be connected to the same supply
phase.● The mains supply to the dimmer(s) must be protected by a suitable fuse
or MCB rated no greater than 16A● Do not exceed maximum control line length of 100m and do not run slave control lines parallel to mains and network cables.● Always observe the transformers recommended loading guidelines.● Load transformers at or close to their full rated capacity. Do not connect
a small load to a larger transformers, (e.g. a 35W lamp on a 600VA transformer)
● Ensure that slaves are wired to the correct control terminals and that the polarity is observed
Vorsicht! ErhöhteStrahlung
Vorsicht! Kontamination Vorsicht! Kontamination Vorsicht, Gefahr durchAbquetschen
Vorsicht, Gefahr durchAbschneiden
Vorsicht, Gefahr durchAbstürzen
Vorsicht, Gefahr durchätzende Stoffe
Vorsicht, Gefahr durchelektrischen Strom
Vorsicht, Gefahr durchelektrischen Strom
Vorsicht, Gefahr durchelektromagnetischeStrahlung
Vorsicht, Gefahr durchexplosionsgefährlicheStoffe
Vorsicht, Gefahr durchfeuergefährliche Stoffe
Vorsicht, Gefahr durchgiftige Stoffe
Vorsicht, Gefahr durchheiße Oberfläche
Vorsicht, Gefahr durchLaserstrahlung
Vorsicht, Gefahr durchRadioaktivität
Vorsicht, Gefahr durchRutschen
Vorsicht, Gefahr durchStolpern
Vorsicht, Gefahr durchVerwickeln
Vorsicht, Warnung voreiner Gefahrstelle
Vorsichtig verschieben!- veraltet -
Während derSchweißarbeiten,Arbeitsstelle beobachten
Wandbrände nicht vonoben löschen
Wandbrände von untennach oben löschen
Wandhydrant Wandhydrant (2.Vorschlag)
Wandhydrant, mit Angabedes Anschlusses
Wareneingang -Freigegeben
Wareneingang - Gesperrt Wärmeabzugseinrichtung
Important: Inductive loads (i.e. conventional wire-wound transformers, etc.) must not be connected to trailing edge dimmers.
Control Wiring for operating Modes 1-7:Control switches T1-3 for operating modes 1-7 should be push-to-make momentary contact switches.Up to 10 operating switches may be wired in parallel with Neon indicators being allowed on control line T1 only
Example1: Multiple control buttons:
L
T
T1
T
T2
T T T
T3
T
Example 2: Wiring for Multiple Master Dimmers with common Central-ON and Central-OFF
L
N
T T TT
T1 T2 T3 L N T1 T2 T3 L N
MASTER DIMMER 1 MASTER DIMMER 2
Load Load
T1 = Separate Dimming control for each master T2 = Central-ON for both master dimmers T3 = Central-OFF for both master dimmers
Control Wiring for operating Mode 8:Control switch T1 for operating mode 8 should be a standard single pole light switch with dimming via the rotary 0/1-10V potentiometer connected between 0-10V and Gnd on the Master dimmer
L
N
T1 T2 T3
+12
V
0-1
0V
Gnd
SE
L N
T
Control input0...10V
Button inputT1 - T3
Mains connection220-240V~ / 50Hz
220V~ / 60Hz
LoadSwitch
Load
Switch
MASTER DIMMER
L N
+12V
0-10V
Gnd SE T1 T2 T3
Mode1
537
8 2
6 4
A1 B1 A2 B2 Slave-Out
R,C R,L
K1402M1kW Trailing Edge Dimmer - MasterFor use with K1401S and K1402S slaves modules
R, C
60-1000VA 50-900VA
P1 P2 ® ®
EN 60669-2-1
50061979-001
ε 220-240V~ / 50Hz220V~ / 60 Hz
F
L N
T5A H250V~
IN Out
IN Out
Slave
A AB B
K1401S1kW Leading Edge Dimmer - SlaveFor use with K1401M and K1402M master modules
R, L
60-1000VA 50-900VA
® ®
EN 60669-2-1
50061978-001
ε 220-240V~ / 50Hz220V~ / 60 Hz
F
L N IN Out
IN Out
Slave
A AB B
K1402S1kW Trailing Edge Dimmer - SlaveFor use with K1401M and K1402M master modules
R, C
® ®
60-1000VA 50-900VA
EN 60669-2-1
50061980-001
ε 220-240V~ / 50Hz220V~ / 60 Hz
F
L N
F
F
F
220-240V~ / 50Hz220V~ / 60Hz Master-dimmer operating Mode 1 – 8
Con
trol c
onne
ctio
n (A
,B)
slav
e di
mm
er
High Power Dimmer Technical
LIGH
TING
CON
TROL
S
Technical Hotline +44 (0)1268 563720
LIGHTING CONTROLS
537
PRODUCT APPLICATIONEDGE SINGLE DIMMER IN GOLD PLATED BESPOKE FINISH
Available on a worldwide basis, the MK Design Service is supported by a dedicated team to ensure the seamless delivery of your chosen products.To find out more visit www.mkelectric.co.uk
PR
OD
UC
T
AP
PL
ICA
TIO
N