Verbindungsteile für Verbund- und
Kunststoffe
Fasteners for lightweight materials and polymers
Auflage 10/2017
HA-CO GmbHTechnische Lösungen
Johann-Roithner-Straße 131A-4050 TraunTel: +43 7229 [email protected]
Haudenschild AGKompetenz in Antriebstechnik
Lidwil 10CH-8852 AltendorfTel: +41 55 225 40 [email protected] www.haudenschild.com
HW-TEC GmbHLineartechnik vom Spezialisten
Lidwil 10CH-8852 AltendorfTel: +41 55 216 10 [email protected]
HA-CO GmbHKupplungen und mehr
Daimlerring 10D-63839 KleinwallstadtTel: +49 602 265 58 [email protected]
Erfahrung die Ihnen zugute kommt
Zuverlässig und sicher
Nutzen Sie unsere Synergien zu Ihrem Vorteil
Experience for your benefit
Reliable and precise
Use our synergies for your advantage
PRODUKTÜBERSICHT UND LEGENDE
Zur Herstellung eines hochbelastbaren Verbindungspunktes in Kunststoff- und Verbundstoffteilen hat man die Möglich-keit, unterschiedliche Verbindungselemente zu verwenden. Bei Kunststoffteilen werden Gewindebuchsen oder -bolzen verwendet, wenn einerseits die Krafteinleitung sehr groß ist oder andererseits ein mehrmaliges Trennen der verbundenen Teile getätigt wird. Die Einbringung des Gewindeeinsatzes erfolgt mittels Eindrehen, Einpressen oder Einlegen während des Formprozesses. Durch die Ausführung mit Rändeln oder Nuten an der Außenform können geforderte Auszugskräfte und gute Verdrehsicherheiten gewährleistet werden.
Eine weitere Möglichkeit, hochbelastbare Verbindungspunkte herzustellen, ist das Einlaminieren oder Aufkleben von Verbindungselementen. Dies wird vorwiegend im GFK- / CFK-Bereich und bei Verbundstoffen benötigt. Durch den großen Flansch kann die Kraft besser eingeleitet werden. Durch eine abgestimmte Verklebung wird auf Anforderungen wie Vibrationen usw. eingegangen.
Zur Verstärkung von Löchern in Kunststoffteilen werden Abstandshalter angebracht. Je nach Anforderung können Buchsen rund, oval, mit oder ohne Längsrändel, mit unterschiedlichen Höhen und Kopfgrößen angeboten werden.
Auch herkömmliche Verbindungselemente – z.B. Blindnieten - können durch Produktausführungen wie größere Klemmbe-reiche oder durch geeignete Ausformung des Schließkopfes eine ideale Befestigung für Kunststoffe darstellen. Der Kunst- oder Verbundstoff wird nicht beschädigt.
MATERIALIENFür die im Katalog ausgewiesenen Teile werden folgende Materialien verwendet. Wenn eine genauere Materialzuordnung benötigt wird, kontaktieren sie unseren Berater oder wenden sie sich per e-mail an uns.
Messingteile: Stahl- bzw. Edelstahlteile:JIS C3604, EN 12164 CW614N, CuZn39Pb3 bb Baustahl mit Fe/Zn 10 Beschichtung oder 316 Edelstahl
Typ Seite Kurzbeschreibung
2
Selbstschneidende Gewindebuchsezum Eindrehen
6
Gewindebuchse zum Warm- oder Kalteinpressen oder zur Ultraschalleinbettung
13
Gewindebuchse zum Einlegen
17
Leichtbaubefestiger zum Einlegen oder Aufkleben
29
Sonstige Befestigungsmöglichkeiten
Legende
L Länge D Durchmesser außen L1
Gewindetiefe h Höhe
T Kopfdurchmesser DK
Kerndurchmesser SW Schlüsselweite lxb Abmessungen Kopf
K Kopfhöhe l1
Länge Ansenkung
FUNKTION
PRODUCT OVERVIEW AND LEGEND
For producing a high resilient fastening point in light weight materials and polymers there is the possibility to use different fastening elements. For polymer parts threaded standoffs or bolts are used when mechanical loads will be induced or the connected parts will be separated several times. The threaded parts are put into the material either with turning in, pres-sing in or moulding in during the moulding process. Using knurls or grooves on the outside of the threaded parts ensure the requested pull out forces and torque values.
Another possibility is the laminating or gluing of fastening elements – predominately in glas fibre / carbon fibre reinforced parts. According to the big flanges the forces can be better induced to the material. Using special adhesives requirements like vibrations etc. will be considered.
For strengthening holes in polymer parts spacers are used. According to the requirements the spacers can be round, oval, with or without longitudinal knurls, with different heights and flange sizes.
Also known fastening elements as blind rivet nuts can be a perfect solution for polymers when they are equipped with big-ger clamping ranges or special forms of retaining (locking) rings. Light weight materials and polymers won’t be damaged.
MATERIALSFor the listed parts in the catalog following materials are used. If you have further questions, please contact our technical staff.
brass: steel and stainless steel:JIS C3604, EN 12164 CW614N, CuZn39Pb3 bb mild steel with Fe/Zn 10 coating and 316 stainless steel
type page short description
2
Self tapping insert for turning in
6
Threaded insert for pressing in warm or cold or for pressing in with ultrasonic
13
Threaded insert for moulding in
17
Light weight fasteners for laminating or gluing
29
Other fastening possibilities
FUNCTION
Legend
L length D outer diameter L1
depth of thread h height
T head diameter DK
core diameter SW width across flats lxb head dimension
K height of head l1
length countersink
Wir verbinden kreative Lösungen mit präziser technischer Umsetzung und bilden so die Schnittstelle zwischen Innovation, Produktion und Vertrieb.
INNOVATIVETECHNOLOGY
Automotive Automotive
Bahn, Truck, Trailer Train, Truck, Trailer
Elektronik Electronics
Medizintechnik Medical technology
Blechbearbeitung Metal processing
Kunststofftechnik Plastics
Luftfahrt Aerospace
Hydraulik Hydraulics
Holzverarbeitung Wood processing
Maschinenbau Mechanical engineering
PRODUKTION PRODUCTION
INN
OVAT
ION
IN
NO
VATIO
N VER
TR
IEB D
ISTR
IBU
TIO
N
TEIL MASCHINE ARBEITSPLATZ LOGISTIK
Verbindungsteil fastener
System system
Automatisierung automation
Shop Floor Solution
We combine creative solutions with precise technical execution, so provi-ding the interface between innovati-on, production and distribution.
PART MACHINE WORKING PLACE LOGISTICS
2 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
EINDREHEN TURNING IN
Bestellbezeichnungorder description
Seitepage
Beschreibungdescription
Anwendungapplication
MGT-M..-BU(KK)DS-"L"MS
3
Selbstschneidende Gewindebuchse mit Schneidschlitz; mit/ohne KopfSelf tapping insert with cutting slot, with/without head
Gewindebuchse zum Eindrehen für Thermo-plaste und Duroplaste.Threaded insert for turning in for thermo-plasts and thermosets.
MGT-M..-BUDS-"L"ST(ES)
4
Selbstschneidende Gewindebuchse mit SchneidschlitzSelf tapping insert with cutting slot
Gewindebuchse zum Eindrehen für Leicht-metalle, Thermoplaste und Duroplaste.Threaded insert is used to create stronger threads in a wide range of soft material as aluminum, light alloy and plastic.
MGT-M..-BU(KK/GK)D-"L"MS
5
Selbstschneidende Gewindebuchse; mit/ohne KopfSelf tapping insert, with/without head
Gewindebuchse zum Eindrehen für Thermoplaste und teilweise Duroplaste; bietet optimalen Sitz durch Nuten.Threaded insert for turning in for thermo-plasts and partly thermosets, optimal setting according to grooves.
MGT-M..-BUD-Q00..
6
Selbstschneidende Sondergewindebuchse mit GewindestoppSelf tapping special insert with thread stop
Gewindebuchse zum Eindrehen für weiche Thermoplaste. Gewindestopp verhindert ein Durchbrechen in den Kunststoff.Threaded insert for turning in for soft thermoplasts. Thread stop avoids damage of polymer.
ANWENDUNGSPRINZIP APPLICATION
Selbstschneidende Gewindeeinsätze können in vielfältigen Materialien eingesetzt werden - in Kunststoffen wie auch Metallen. Dazu wird eine Bohrung in das Material eingebracht und der Gewindeeinsatz mit Schrauber oder speziellem Werkzeug eingedreht. Self tapping inserts can be used in different materials – in polymers and in metals. A hole will be made into the material and the threaded part will be inserted with a screwdriver or special tool.
3© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
SELBSTSCHNEIDENDE GEWINDEBUCHSE MIT SCHNEIDSCHLITZSELF TAPPING INSERT FOR TURNING IN WITH CUTTING SLOT
Bestellbezeichnung: MGT-M..-BU(KK)DS-"L"MS
order description:
L
K
T
L
D
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
KK Kleiner Kopf small head
D zum Eindrehen turning in
S Schneidschlitz cutting slot
L Länge length
MS Material Messing material brass
Bezeichnung typeGewinde thread
L T K D
Bohrloch hole diameter Thermoplast
thermoplastic
Bohrlochhole diameter
Duroplast thermoset
MGT-M2.5-BUDS-6MSM2.5
6 4,5 4,0 4,1
MGT-M2.5-BUKKDS-6MS 6 6,0 0,58 4,5 4,0 4,1
MGT-M3-BUDS-6MSM3
6 5,0 4,5 4,6
MGT-M3-BUKKDS-6MS 6 6,5 0,58 5,0 4,5 4,6
MGT-M3.5-BUDS-8MSM3.5
8 6,0 5,3 5,5
MGT-M3.5-BUKKDS-8MS 8 7,5 0,73 6,0 5,3 5,5
MGT-M4-BUDS-8MSM4
8 6,5 5,8 6,0
MGT-M4-BUKKDS-8MS 8 8,0 0,89 6,5 5,8 6,0
MGT-M5-BUDS-10MSM5
10 8,0 7,1 7,3
MGT-M5-BUKKDS-10MS 10 9,5 1,06 8,0 7,1 7,3
MGT-M6-BUDS-14MSM6
14 10,0 8,6 9,0
MGT-M6-BUKKDS-14MS 14 12,0 1,32 10,0 8,6 9,0
MGT-M8-BUDS-15MSM8
15 12,0 10,6 11,0
MGT-M8-BUKKDS-15MS 15 14,0 1,32 12,0 10,6 11,0
MGT-M10-BUDS-18MSM10
18 14,0 12,6 13,0
MGT-M10-BUKKDS-18MS 18 16,0 1,57 14,0 12,6 13,0
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
EIN
DR
EH
EN
T
UR
NIN
G I
N
4 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
SELBSTSCHNEIDENDE GEWINDEBUCHSE MIT SCHNEIDSCHLITZSELF TAPPING INSERT FOR TURNING IN WITH CUTTING SLOT
Bestellbezeichnung: MGT-M..-BUDS-"L"ST(ES)
order description:
L
D
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
D zum Eindrehen turning in
S Schneidschlitz cutting slot
L Länge length
ST Material Stahl verzinkt material steel zinc plated
ES Material Edelstahl material stainless steel
Bezeichnung typeGewinde thread
LD-AußengewindeD-outside thread
min. Lochtiefemin. hole depth
Bohrloch hole diameter ST Stahl verzinkt
ST steel zinc platedES Edelstahl
ES stainless steel
MGT-M2.5-BUDS-6ST MGT-M2.5-BUDS-6ES M2.5 6 M4.5x0.5 8 4,0 - 4,3
MGT-M3-BUDS-6ST MGT-M3-BUDS-6ES M3 6 M5x0.5 8 4,5 - 4,8
MGT-M4-BUDS-8ST MGT-M4-BUDS-8ES M4 8 M6.5x0.75 10 5,8 - 6,2
MGT-M5-BUDS-10ST MGT-M5-BUDS-10ES M5 10 M8x1.0 13 7,1 - 7,6
MGT-M6-BUDS-14ST MGT-M6-BUDS-14ES M6 14 M10x1.5 17 8,6 - 9,4
MGT-M8-BUDS-15ST MGT-M8-BUDS-15ES M8 15 M12x1.5 18 10,6 - 11,4
MGT-M10-BUDS-18ST MGT-M10-BUDS-18ES M10 18 M14x1.5 22 12,6 - 13,4
MGT-M12-BUDS-22ST MGT-M12-BUDS-22ES M12 22 M16x1.5 26 14,6 - 15,4
MGT-M14-BUDS-24ST MGT-M14-BUDS-24ES M14 24 M18x1.5 28 16,6 - 17,4
MGT-M16-BUDS-22ST MGT-M16-BUDS-22ES M16 22 M20x1.5 27 18,6 - 19,4
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
5© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
SELBSTSCHNEIDENDE GEWINDEBUCHSESELF TAPPING INSERT FOR TURNING IN
L
D
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
KK/GK Kleiner Kopf, (GK) Großer Kopf small head, large head
D zum Eindrehen turning in
L Länge length
MS Material Messing material brass
L
DT
K MGT-M..-BU(KK/GK)D-"L"MS
Bezeichnung typeGewinde thread
L T K DBohrloch
hole diameter
MGT-M2-BUD-4.8MS M2 4,8 3,5 3,1
MGT-M2.5-BUD-5.25MS M2.5 5,25 4,33 3,8
MGT-M3-BUD-4MS
M3
4,0 4,73 4,1
MGT-M3-BUD-5.25MS 5,25 4,73 4,1
MGT-M3-BUD-6.25MS 6,25 4,73 4,1
MGT-M3-BUGKD-5.25MS 5,25 7,1 0,75 4,73 4,1
MGT-M3.5-BUD-6.2MS M3.5 6,2 5,52 5,0
MGT-M4-BUD-5.6MS
M4
5,6 6,31 5,8
MGT-M4-BUD-7.1MS 7,1 6,31 5,8
MGT-M4-BUD-8.4MS 8,4 6,31 5,8
MGT-M4-BUKKD-8.4MS 8,4 6,3 0,8 6,31 5,8
MGT-M4-BUGKD-7.1MS 7,1 8,7 0,75 6,31 5,8
MGT-M5-BUD-6.4MS
M5
6,4 7,5 6,9
MGT-M5-BUD-8.4MS 8,4 7,5 6,9
MGT-M5-BUD-10MS 10,0 7,5 6,9
MGT-M5-BUKKD-10MS 10,0 7,5 0,8 7,5 6,9
MGT-M5-BUGKD-8.4MS 8,4 11,1 0,9 7,5 6,9
MGT-M6-BUD-7.9MS
M6
7,9 8,69 8,0
MGT-M6-BUD-9.8MS 9,8 8,69 8,0
MGT-M6-BUD-12MS 12,0 8,69 8,0
MGT-M6-BUKKD-12MS 12,0 8,7 0,9 8,69 8,0
MGT-M6-BUGKD-9.8MS 9,8 12,0 1,0 8,69 8,0
MGT-M8-BUD-12.4MS
M8
12,4 11,06 10,1
MGT-M8-BUKKD-14.1MS 14,1 11,1 1,0 11,06 10,1
MGT-M8-BUGKD-12.4MS 12,4 14,3 1,25 11,06 10,1
MGT-M10-BUD-16MS M10 16,0 13,95 13,0
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
Bestellbezeichnung: order description:
EIN
DR
EH
EN
T
UR
NIN
G I
N
6 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
SELBSTSCHNEIDENDE GEWINDEBUCHSE MIT GEWINDESTOPPSELF TAPPING INSERT FOR TURNING IN WITH THREAD STOPP
Bezeichnung typeGewinde thread
L D DK
MGT-M6-BUD-Q0002 M6 13 12,5 9
MGT-M8-BUD-Q0002 M8 13 14,5 10
MGT-M12-BUD-Q0002 M12 25 23,0 18
MGT-M16-BUD-Q0002 M16 25 25,0 20
MGT-M20-BUD-Q0002 M20 30 25,0 25
weitere Dimensionen auf Anfrage
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
L
DDK
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
D zum Eindrehen turning in
Q Sonderteil special part
.. laufende Nummer current number
Bestellbezeichnung: MGT-M..-BUD-Q..
order description:
7© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
EINPRESSEN PRESSING IN
Bestellbezeichnungorder description
Seitepage
Beschreibungdescription
Anwendungapplication
MGT-M..-BU(KK/GK)P-"L"MS
8
Gewindebuchse zum Einpressen; mit/ohne KopfThreaded insert for pressing in, with /without head
Gewindebuchse, die zum Warmeinpressen oder zur Ultraschalleinbettung für Thermoplaste und Duroplaste verwendet werden kann.Threaded insert for pressing in warm or with ultrasonics for themoplasts and thermosets.
MGT-M..BU(KK)PK-"L"MS
10
Gewindebuchse zum Einpressen für riss- empfindliche Kunststoffemit/ohne KopfThreaded insert for pressing in for notch sensitive plastics, with /without head
Gewindebuchse, die zum Warmeinpressen oder zur Ultraschalleinbettung für Thermoplaste wie PC, PMMA und ähnlichen rissempfindlichen Kunststoffen verwendet werden kann. Durch ihre geschwungene Rändelform schädigt sie den Kunststoff nicht. Threaded insert for pressing in warm or with ultrasonics for notch sensitive plastics like PC, PMMA and similar materials. According to the rolling knurls.
MGT-M..BUPZ-"L"MS
11
Gewindebuchse zum Einpressen, beidsei-tig einsetzbarThreaded insert for pressing in, symme-trically
Gewindebuchse zum Warmeinpressen oder zur Ultraschalleinbettung für Thermoplaste, die aufgrund ihrer symmetrischen Form beidseitig einsetzbar ist und damit für eine Automatisie-rung besonders gut geeignet ist.Symmetrically formed threaded insert for pres-sing in warm or with ultrasonic of thermoplasts, which can be put into the material with both sides. Good application for automation.
MGT-M..-BU(KK)PVS-"L"MS
12
Expandierende Gewindebuchse zum Kalteinpressen für DuroplasteExpanding threaded insert for cold pres-sing in for thermosets
Gewindebuchse zum Kalteinpressen, die durch ihre Rändelung besonders für Duroplaste geeignet ist. Threaded insert for cold pressing in, especially for thermosets according to the knurls.
MGT-M..BU(KK)PV-"L"MS
13
Gewindebuchse zum Kalteinpressen für DuroplasteThreaded insert for cold pressing in for thermosets
Gewindebuchse zum Kalteinpressen für Duro-plaste. Die scharfe Rändelung schneidet sich ins Material und vermeidet gleichzeitig Spannungs-aufbau in spröden Materialien.Threaded insert for cold pressing in for ther-mosets. Sharp knurls cut into the material and therefore avoids stress in rigid materials.
ANWENDUNGSPRINZIP APPLICATION
Einpressteile können kalt und warm eingepresst werden oder auch mit Ultraschall eingebettet werden. Welches Verfahren verwendet wird, hängt von der Art der Anwendung und Wahl des Kunststoffes ab. Bei der Warmeinbettung soll der Gewin-deeinsatz den Kunststoff erwärmen, aber nicht schmelzen. Dies verhindert die Gratbildung an der Grenzfläche zwischen Einsatz und Material. Information zu Thermopressen können Sie gesondert anfordern. Bei der Ultraschalleinbettung werden niedrige Frequenzen empfohlen, um den Kunststoff zu erwärmen. Pressing in inserts can be inserted cold or warm or with ultrasonic. Which system is used depends on the application and choice of the polymer. For pressing in warm the threaded insert should only heat the material and not melt it. This avoids burr formation on the surface between insert and material. Information to heat inserters can be requested separately. For ultrasonic insertion low frequencies are recommended to heat up the material.
EIN
PR
ES
SE
N
PR
ES
SIN
G I
N
8 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEBUCHSE ZUM WARMEINPRESSEN ODER ZUR ULTRASCHALLEINBETTUNG FÜR THERMOPLASTETHREADED INSERT FOR PRESSING IN WARM OR FOR PRESSING IN WITH ULTRASONIC FOR THERMOPLASTICS
L
K
T D
Bezeichnung typeGewinde thread
L T K DBohrloch
hole diameter
MGT-M2-BUP-4.2MS
M2
4,2 3,5 3,3
MGT-M2-BUKKP-2.1MS 2,1 4,8 0,5 3,5 3,3
MGT-M2-BUKKP-4.2MS 4,2 4,8 0,5 3,5 3,3
MGT-M2.5-BUP-4.1MS
M2.5
4,1 4,3 4,0
MGT-M2.5-BUP-5.2MS 5,2 4,3 4,0
MGT-M2.5-BUKKP-4.1MS 4,1 5,5 0,75 4,3 4,0
MGT-M2.5-BUKKP-5.2MS 5,2 5,5 0,75 4,3 4,0
MGT-M2.5-BUGKP-4.1MS 4,1 7,1 0,75 4,3 4,0
MGT-M2.5-BUGKP-5.2MS 5,2 7,1 0,75 4,3 4,0
MGT-M3-BUP-4.1MS
M3
4,1 4,3 4,0
MGT-M3-BUP-5.2MS 5,2 4,3 4,0
MGT-M3-BUKKP-4,1MS 4,1 5,5 0,75 4,3 4,0
MGT-M3-BUKKP-5.2MS 5,2 5,5 0,75 4,3 4,0
MGT-M3-BUGKP-4.1MS 4,1 7,1 0,75 4,3 4,0
MGT-M3-BUGKP-5.2MS 5,2 7,1 0,75 4,3 4,0
>
L
D
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
KK/GK Kleiner Kopf, (GK) Großer Kopf small head, large head
P zum Einpressen pressing in
L Länge length
MS Material Messing material brass
BestellbezeichnungBestellbezeichnung: MGT-M..-BU(KK/GK)P-"L"MS
order description:
9© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
MGT-M3.5-BUP-4.1MS
M3.5
4,1 5,5 5,0
MGT-M3.5-BUP-7.0MS 7,0 5,5 5,0
MGT-M3.5-BUKKP-4.1MS 4,1 6,4 0,75 5,5 5,0
MGT-M3.5-BUKKP-7.0MS 7,0 6,4 0,75 5,5 5,0
MGT-M3.5-BUGKP-4.1MS 4,1 7,9 0,75 5,5 5,0
MGT-M3.5-BUGKP-7.0MS 7,0 7,9 0,75 5,5 5,0
MGT-M4-BUP-5.6MS
M4
5,6 6,3 5,75
MGT-M4-BUP-8.5MS 8,5 6,3 5,75
MGT-M4-BUKKP-5.6MS 5,6 7,1 0,75 6,3 5,75
MGT-M4-BUKKP-8.5MS 8,5 7,1 1,0 6,3 5,75
MGT-M4-BUGKP-5.6MS 5,6 8,7 0,75 6,3 5,75
MGT-M4-BUGKP-8.5MS 8,5 8,7 1,0 6,3 5,75
MGT-M5-BUP-6.6MS
M5
6,6 7,05 6,4
MGT-M5-BUP-10.1MS 10,1 7,05 6,4
MGT-M5-BUKKP-6.6MS 6,6 7,9 1,0 7,05 6,4
MGT-M5-BUKKP-10.1MS 10,1 7,9 1,0 7,05 6,4
MGT-M5-BUGKP-6.6MS 6,6 11,1 1,0 7,05 6,4
MGT-M5-BUGKP-10.1MS 10,1 11,1 1,0 7,05 6,4
MGT-M6-BUP-7.7MS
M6
7,7 8,65 8,0
MGT-M6-BUP-12.3MS 12,3 8,65 8,0
MGT-M6-BUKKP-7.7MS 7,7 9,5 1,3 8,65 8,0
MGT-M6-BUKKP-12.3MS 12,3 9,5 1,25 8,65 8,0
MGT-M6-BUGKP-7.7MS 7,7 12,7 1,3 8,65 8,0
MGT-M6-BUGKP-12.3MS 12,3 12,7 1,25 8,65 8,0
MGT-M8-BUP-8.3MS
M8
8,3 11,05 10,5
MGT-M8-BUP-13.8MS 13,8 11,05 10,5
MGT-M8-BUKKP-10.1MS 10,1 12,7 1,25 11,05 10,5
MGT-M8-BUGKP-10.1MS 10,1 14,3 1,25 11,05 10,5
MGT-M8-BUGKP-13.8MS 13,8 14,3 1,25 11,05 10,5
MGT-M10-BUP-10.1MS
M10
10,1 12,5 12,9
MGT-M10-BUP-16.1MS 16,1 12,5 12,9
MGT-M10-BUKKP-10.1MS 10,1 14,3 1,25 12,5 12,9
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
Bezeichnung typeGewinde thread
L T K DBohrloch
hole diameter
EIN
PR
ES
SE
N
PR
ES
SIN
G I
N
10 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEBUCHSE ZUM WARMEINPRESSEN FÜR RISSEMPFINDLICHE KUNSTSTOFFETHREADED INSERT FOR PRESSING IN WARM FOR NOTCH SENSITIVE PLASTICS
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
KK Kleiner Kopf small head
P zum Einpressen pressing in
K für rissempfindliche Kunststoffe for notch sensitive plastics
L Länge length
MS Material Messing material brass
BestellbezeichnungBestellbezeichnung: MGT-M..-BU(KK)PK-"L"MS
order description:
L
K
T DDK
L
DDK
Bezeichnung typeGewinde thread
L T K D DK
Bohrloch hole diameter
MGT-M2-BUPK-3.9MSM2
3,9 3,5 3,1 3,2
MGT-M2-BUKKPK-3.9MS 3,9 4,8 0,51 3,5 3,1 3,2
MGT-M2.5-BUPK-5.8MSM2.5
5,8 4,4 3,9 4,0
MGT-M2.5-BUKKPK-5.8MS 5,8 5,5 0,58 4,4 3,9 4,0
MGT-M3-BUPK-5.8MSM3
5,8 4,4 3,9 4,0
MGT-M3-BUKKPK-5.8MS 5,8 5,5 0,58 4,4 3,9 4,0
MGT-M3.5-BUPK-7.1MSM3.5
7,1 5,2 4,7 4,8
MGT-M3.5-BUKKPK-7.1MS 7,1 6,4 0,74 5,2 4,7 4,8
MGT-M4-BUPK-8.1MSM4
8,1 6,1 5,5 5,6
MGT-M4-BUKKPK-8.1MS 8,1 7,1 0,89 6,1 5,5 5,6
MGT-M5-BUPK-9.5MSM5
9,5 6,9 6,3 6,4
MGT-M5-BUKKPK-9.5MS 9,5 7,9 1,07 6,9 6,3 6,4
MGT-M6-BUPK-12.7MSM6
12,7 8,5 7,9 8,0
MGT-M6-BUKKPK-12.7MS 12,7 9,5 1,32 8,5 7,9 8,0
MGT-M8-BUPK-12.7MSM8
12,7 10,0 9,5 9,6
MGT-M8-BUKKPK-12.7MS 12,7 11,1 1,32 10,0 9,5 9,6
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
11© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEBUCHSE ZUM WARMEINPRESSEN ODER ZUR ULTRASCHALLEINBETTUNG MIT SYMMETRISCHER AUSFÜHRUNG SYMMETRICALLY FORMED THREADED INSERT FOR PRESSING IN WARM OR WITH ULTRASONIC OF THERMOPLASTS
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
P zum Einpressen pressing in
Z zentriert bzw. symmetrisch symmetrically
L Länge length
MS Material Messing material brass
BestellbezeichnungBestellbezeichnung: MGT-M..-BUPZ-"L"MS
order description:
L
DDK
Bezeichnung typeGewinde thread
L D DK
Bohrloch hole diameter
MGT-M2-BUPZ-4MS M2 4,0 3,5 3,1 3,2
MGT-M2.5-BUPZ-5.7MS M2.5 5,7 4,4 3,9 4,0
MGT-M3-BUPZ-5.7MS M3 5,7 4,4 3,9 4,0
MGT-M3.5-BUPZ-7.1MS M3.5 7,1 5,2 4,7 4,8
MGT-M4-BUPZ-8.1MS M4 8,1 6,1 5,5 5,6
MGT-M5-BUPZ-9.5MS M5 9,5 6,8 6,3 6,4
MGT-M6-BUPZ-12.7MS M6 12,7 8,5 7,9 8,0
MGT-M8-BUPZ-12.7MS M8 12,7 10,0 9,5 9,6
MGT-M10-BUPZ-12.7MS M10 12,7 12,3 11,8 11,9
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
EIN
PR
ES
SE
N
PR
ES
SIN
G I
N
12 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
EXPANDIERENDE GEWINDEBUCHSE FÜR DUROPLASTE EXPANDING THREADED INSERT FOR THERMOSETS
L
K
T D
L
D
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
KK Kleiner Kopf small head
P zum Einpressen pressing in
V für verstärkte Kunststoffe oder Duroplaste for strengthened plastics and thermosets
S Spreiz expanding
L Länge length
MS Material Messing material brass
BestellbezeichnungBestellbezeichnung: MGT-M..-BU(KK)PVS-"L"MS
order description:
Bezeichnung typeGewinde thread
L T K DBohrloch
hole diameter
MGT-M2-BUPVS-3.9MSM2
3,9 3,2 3,2
MGT-M2-BUKKPVS-3.9MS 3,9 4,8 0,43 3,2 3,2
MGT-M2.5-BUPVS-4.7MSM2.5
4,7 4,0 4,0
MGT-M2.5-BUKKPVS-4.7MS 4,7 5,5 0,51 4,0 4,0
MGT-M3-BUPVS-4.7MSM3
4,7 4,0 4,0
MGT-M3-BUKKPVS-4.7MS 4,7 5,5 0,51 4,0 4,0
MGT-M3.5-BUPVS-6.3MSM3.5
6,3 4,7 4,8
MGT-M3.5-BUKKPVS-6.3MS 6,3 6,4 0,66 4,7 4,8
MGT-M4-BUPVS-7.9MSM4
7,9 5,5 5,6
MGT-M4-BUKKPVS-7.9MS 7,9 7,1 0,82 5,5 5,6
MGT-M5-BUPVS-9.4MSM5
9,4 6,3 6,4
MGT-M5-BUKKPVS-9.4MS 9,4 7,9 0,99 6,3 6,4
MGT-M6-BUPVS-12.6MSM6
12,6 7,9 8,0
MGT-M6-BUKKPVS-12.6MS 12,6 9,5 1,25 7,9 8,0
MGT-M8-BUPVS-12.6MSM8
12,6 9,5 9,6
MGT-M8-BUKKPVS-12.6MS 12,6 11,1 1,25 9,5 9,6
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
13© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEBUCHSE ZUM KALTEINPRESSEN FÜR DUROPLASTETHREADED INSERT FOR PRESSING IN COLD FOR THERMOSETS
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
KK Kleiner Kopf small head
P zum Einpressen pressing in
V für verstärkte Kunststoffe oder Duroplaste for strengthened plastics and thermosets
L Länge length
MS Material Messing material brass
BestellbezeichnungBestellbezeichnung: MGT-M..-BU(KK)PV-"L"MS
order description:
L
K
T DDK
L
D DK
Bezeichnung typeGewinde thread
L T K D DK
Bohrloch hole diameter
MGT-M2-BUPV-4.1MSM2
4,1 3,4 3,0 3,1
MGT-M2-BUKKPV-4.1MS 4,1 4,8 0,55 3,4 3,0 3,1
MGT-M2.5-BUPV-5.3MSM2.5
5,3 4,2 3,7 3,8
MGT-M2.5-BUKKPV-5.3MS 5,3 5,6 0,55 4,2 3,7 3,8
MGT-M3-BUPV-5.3MSM3
5,3 4,2 3,7 3,8
MGT-M3-BUKKPV-5.3MS 5,3 5,6 0,55 4,2 3,7 3,8
MGT-M3.5-BUPV-6.3MSM3.5
6,3 5,0 4,5 4,6
MGT-M3.5-BUKKPV-6.3MS 6,3 6,4 0,7 5,0 4,5 4,6
MGT-M4-BUPV-7.4MSM4
7,4 5,8 5,3 5,4
MGT-M4-BUKKPV-7.4MS 7,4 7,2 0,8 5,8 5,3 5,4
MGT-M5-BUPV-8.3MSM5
8,3 6,6 6,1 6,2
MGT-M5-BUKKPV-8.3MS 8,3 7,8 1,0 6,6 6,1 6,2
MGT-M6-BUPV-9.2MSM6
9,2 8,2 7,7 7,8
MGT-M6-BUKKPV-9.2MS 9,2 9,5 1,3 8,2 7,7 7,8
MGT-M8-BUPV-9.2MSM8
9,2 9,7 9,3 9,3
MGT-M8-BUKKPV-9.2MS 9,2 11,0 1,3 9,7 9,3 9,3
MGT-M10-BUPV-9.2MSM10
9,2 12,7 12,3 12,3
MGT-M10-BUKKPV-9.2MS 9,2 14,0 1,6 12,7 12,3 12,3
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
EIN
PR
ES
SE
N
PR
ES
SIN
G I
N
14 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
EINLEGEN MOULDING
Bestellbezeichnungorder description
Seitepage
Beschreibungdescription
Anwendungapplication
MGT-M..-BUR(G)-"L"MS
15
Gewindebuchse zum EinlegenThreaded insert for moul-ding in
Gewindebuchse zum Einlegen. Die Buchse kann geschlossen oder offen ausgeführt sein.Threaded insert for moulding in. Insert can be open or closed.
MGT-M..-BUR(G)-Q00..
16
Sondergewindebuchse zum EinlegenSpecial threaded insert for moulding
Gewindebuchse zum Einlegen, die nach Standardmaßen oder gewünschten Maßen gefertigt werden kann.Special threaded insert for moulding in, which are produced according to standard or requested measures.
MGT-M..-BURH(G)-"L"MS
17
Hexagonale Gewinde-buchseHexagonal threaded insert
Hexagonale Gewindebuchse, die speziell für das Rotationsschmelzverfahren verwendet wird. Durch ihre spezielle Form wird eine große Kunststofffläche abgedeckt.Hexagonal threaded insert especially for rotational moulding. Due to the special form a big polymer surface will be covered.
MGT-M..-BU16903C(R)-MS(ST/ES)
18
Gewindebuchsen DIN 16903 (Norm 1974) - Form C und RThreaded insert DIN 16903 (Norm 1974)Form C und R
Meist hexagonale Gewindebuchse nach DIN16903. Durch ihre spezielle Form wird eine große Kunststofffläche abgedeckt und so gegen Rotation gewirkt.Mostly hexagonal threaded insert according to DIN 16903. Due to the special form a big polymer surface will be covered and there-fore counters against rotation.
ANWENDUNGSPRINZIP APPLICATION
Die Einlegeteile werden während des Formgebungsprozesses in das Werkzeug eingelegt und umspritzt. Die geschlossenen Einsätze verhindern das Eindringen des Kunststoffes in das Gewinde. Bei der Konstruktion des Pins muss darauf geachtet werden, dass die Toleranzen so gewählt sind, dass ebenfalls kein Kunststoff in das Gewinde fließen kann. Das Einlegen ermöglicht gute Fertigungszeiten im Spitzgussprozess, da die Teile automatisch zugeführt werden können.Moulding inserts will be positioned in the tooling during the moulding process and then covered with material. Closed parts avoid the intrusion of polymer into the thread. When developing the pin tolerances must be considered also to avoid intrusion of the material. Moulding inserts allow good process times in the moulding process as parts can be fed automa-tically.
15© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEBUCHSE ZUM EINLEGENTHREADED INSERT FOR MOULDING
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
R zum Einlegen for moulding
G geschlossen closed
L Länge length
MS Material Messing material brass
L
D
L1
l1
Bezeichnung typeGewinde thread
L L1
D l1
MGT-M2-BURG-5.5MS M2 5,5 3,6 3,4 1,0
MGT-M2.5-BURG-6.4MS M2.5 6,4 4,0 4,3 1,15
MGT-M3-BURG-7.3MS M3 7,3 4,6 4,7 1,3
MGT-M3.5-BURG-9.2MS M3.5 9,2 6,0 5,5 1,55
MGT-M4-BURG-10.2MS M4 10,2 6,7 6,3 1,8
MGT-M5-BURG-11.2MS M5 11,2 7,4 7,3 1,95
MGT-M6-BURG-14.4MS M6 14,4 8,1 9,8 2,05
MGT-M8-BURG-16.5MS M8 16,5 11,1 11,4 2,25
MGT-M10-BURG-17.9MS M10 17,9 11,9 13,8 2,35
für Buchsefor insert
e f g h i j
M2 0,8 1,55 2,65 2,3 6,0 3,0
M2.5 0,9 2,0 3,0 2,8 5,0 3,5
M3 1,05 2,45 3,4 3,1 4,5 4,0
M3.5 1,3 2,85 4,55 3,75 4,5 4,7
M4 1,55 3,25 5,0 4,43 4,5 5,4
M5 1,7 4,15 5,55 5,13 5,0 6,0
M6 1,8 4,95 6,15 6,6 5,5 8,0
M8 2,0 6,7 9,0 8,5 6,0 10,0
M10 2,1 8,4 9,7 10,5 6,0 12,0
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
g
j
h
f
ie
AUFNAHMESTIFT PIN
MGT-M..-BUR(G)-"L"MS
Bestellbezeichnung: order description:
EIN
LE
GE
N
MO
UL
DIN
G
16 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
Bezeichnung typeGewinde thread
L D L1
MGT-M2.5-BURG-Q0001M2.5
4,7 4,78 2,01
MGT-M2.5-BURG-Q0002 9,5 4,78 4,6
MGT-M3-BURG-Q0001M3
5,2 4,78 2,21
MGT-M3-BURG-Q0002 10,3 4,78 5,21
MGT-M3.5-BURG-Q0001M3.5
6,3 5,56 2,62
MGT-M3.5-BURG-Q0002 11,9 5,56 6,22
MGT-M4-BURG-Q0001M4
6,3 6,35 3,08
MGT-M4-BURG-Q0002 11,9 6,35 7,29
MGT-M5-BURG-Q0001M5
7,1 7,14 3,49
MGT-M5-BURG-Q0002 11,9 7,14 8,29
MGT-M6-BURG-Q0001M6
8,73 8,74 4,37
MGT-M6-BURG-Q0002 18,26 8,74 10,57
MGT-M8-BURG-Q0001M8
11,1 11,13 5,72
MGT-M8-BURG-Q0002 20,6 11,13 12,82
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
SONDERGEWINDEBUCHSE ZUM EINLEGENSPECIAL THREADED INSERT FOR MOULDING
BestellbezeichnungBestellbezeichnung: MGT-M..-BUR(G)-Q..
order description:
L
D
L1
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
R zum Einlegen for moulding
G geschlossen closed
Q Sonderteil special part
.. laufende Nummer current number
17© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
HEXAGONALE GEWINDEBUCHSE FÜR DAS ROTATIONSSCHMELZVERFAHRENHEXAGONAL THREADED INSERT ESPECIALLY FOR ROTATIONAL MOULDING
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
R zum Einlegen for moulding
H sechskant hexagonal
G geschlossen closed
L Länge length
MS Material Messing material brass
L
DK
SW
Bezeichnung typeGewinde thread
L DK
SWAnzahl der Einkerbungen
number of notches
MGT-M4-BURHG-8.5MSM4
8,5 6,1 8,0 2
MGT-M4-BURH-8.5MS 8,5 6,1 8,0 2
MGT-M5-BURHG-10MSM5
10,0 6,1 8,0 2
MGT-M5-BURH-10MS 10,0 6,1 8,0 2
MGT-M6-BURHG-10MS
M6
10,0 7,7 10,0 2
MGT-M6-BURH-10MS 10,0 7,7 10,0 2
MGT-M6-BURHG-15MS 15,0 7,7 10,0 3
MGT-M6-BURH-15MS 15,0 7,7 10,0 3
MGT-M8-BURHG-16MS
M8
16,0 9,8 12,0 3
MGT-M8-BURH-16MS 16,0 9,8 12,0 3
MGT-M8-BURHG-19MS 19,0 9,8 12,0 4
MGT-M8-BURH-19MS 19,0 9,8 12,0 4
MGT-M10-BURHG-16MS
M10
16,0 11,8 14,0 3
MGT-M10-BURH-16MS 16,0 11,8 14,0 3
MGT-M10-BURHG-19MS 19,0 11,8 14,0 4
MGT-M10-BURH-19MS 19,0 11,8 14,0 4
MGT-M12-BURHG-19MSM12
19,0 13,5 16,0 4
MGT-M12-BURH-19MS 19,0 13,5 16,0 4
MGT-M14-BURHG-19MSM14
19,0 15,8 18,0 4
MGT-M14-BURH-19MS 19,0 15,8 18,0 4
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
MGT-M..-BURH(G)-"L"MS
Bestellbezeichnung: order description:
EIN
LE
GE
N
MO
UL
DIN
G
18 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
Bezeichnung typeGewinde thread
L L1
D DK
SW
MGT-M3-BU16903C-MS/ST/ES M3 4,5 1,2 5,8 3,8 5,0
MGT-M4-BU16903C-MS/ST/ES M4 6,0 1,4 6,9 5,0 6,0
MGT-M5-BU16903C-MS/ST/ES M5 7,5 2,5 8,1 6,4 7,0
MGT-M6-BU16903C-MS/ST/ES M6 9,0 3,0 10,4 7,4 9,0
MGT-M8-BU16903C-MS/ST/ES M8 12,0 4,0 12,7 10,4 11,0
MGT-M10-BU16903C-MS/ST/ES M10 15,0 6,0 16,2 13,0 14,0
MGT-M12-BU16903C-MS/ST/ES M12 18,0 7,0 21,9 17,0 19,0
Alle Angaben in mm. Weitere Formen (A,B,D,P,Q,S) auf Anfrage.All information stated in mm. Further designs (A,B,D,P,Q,S) on request.
GEWINDEBUCHSE DIN 16903 (NORM 1974) - FORM CTHREADED INSERT DIN 16903 (NORM 1974) - DESIGN C
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
16903 Norm standard
C Form design
MS Material Messing (MS58) material brass (MS58)
ST Material Stahl (1.0718) material steel (1.0718)
ES Material Edelstahl (1.4305) material stainless steel (1.4305)
BestellbezeichnungBestellbezeichnung: MGT-M..-BU16903C-MS(ST/ES)
order description:
19© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEBUCHSE GESCHLOSSEN DIN 16903 (NORM 1974) - FORM RTHREADED INSERT CLOSED DIN 16903 (NORM 1974) - DESIGN R
EIN
LE
GE
N
MO
UL
DIN
G
Bezeichnung typeGewinde thread
L L1
D DK
SW
MGT-M3-BU16903R-MS/ST/ES M3 7,0 1,8 5,8 3,8 5,0
MGT-M4-BU16903R-MS/ST/ES M4 9,0 2,8 6,9 5,0 6,0
MGT-M5-BU16903R-MS/ST/ES M5 10,8 3,5 8,1 6,4 7,0
MGT-M6-BU16903R-MS/ST/ES M6 12,8 4,0 10,4 7,4 9,0
MGT-M8-BU16903R-MS/ST/ES M8 16,6 5,5 12,7 10,4 11,0
MGT-M10-BU16903R-MS/ST/ES M10 20,0 6,0 16,2 13,0 14,0
MGT-M12-BU16903R-MS/ST/ES M12 23,8 7,0 21,9 17,0 19,0
Alle Angaben in mm. Weitere Formen (A,B,D,P,Q,S) auf Anfrage.All information stated in mm. Further designs (A,B,D,P,Q,S) on request.
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
16903 Norm standard
R Form design
MS Material Messing (MS58) material brass (MS58)
ST Material Stahl (1.0718) material steel (1.0718)
ES Material Edelstahl (1.4305) material stainless steel (1.4305)
BestellbezeichnungBestellbezeichnung: MGT-M..-BU16903R-MS(ST/ES)
order description:
EINLAMINIEREN / AUFKLEBEN LAMINATING / GLUING
Bestellbezeichnungorder description
Seitepage
Beschreibungdescription
Anwendungapplication
MGT-M..-BO-..-"L"ST(ES)
21
Gewindebolzen mit großem FlanschThreaded bolt with big flange
Gewindebolzen mit großem Flansch, der einlaminiert oder aufgeklebt werden kann. Dieser Befestigungsteil ist speziell für die GFK- und CFK-Fertigung geeignet.Stud with big flange which can be laminated or glued. This part is especially for glass fibre and carbon fibre reinforced production.
MGT-4.75-..-"L"ST(ES)
23
Stift mit großem FlanschPin with big flange
Stift mit großem Flansch, der einlaminiert oder aufgeklebt werden kann.Dieser Befestigungsteil ist speziell für die GFK- und CFK-Fertigung geeignet.Pin with big flange which can be laminated or glued. This part is especially for glass fibre and carbon fibre reinforced production.
MGT-M..-BU(G)-..-"L"ST(ES)
24
Gewindebuchse mit großem FlanschStandoff with big flange
Gewindebuchse mit großem Flansch, der einlaminiert oder aufgeklebt werden kann.Dieser Befestigungsteil ist speziell für die GFK- und CFK-Fertigung geeignet.Standoff with big flange which can be laminated or glued. This part is especially for glass fibre and carbon fibre reinforced production.
MGT-M..-MU(G)-..-"L"ST(ES)
28
Mutter mit großem Flansch Nut with big flange
Mutter mit großem Flansch, die einlaminiert oder aufgeklebt werden kann.Dieser Befestigungsteil ist speziell für die GFK- und CFK-Fertigung geeignet.Nut with big flange which can be laminated or glued. This part is especially for glass fibre and carbon fibre reinforced production.
MGT-M..-AH..-"L"-AL
32
Buchse für VerbundpaneleThreaded insert for light weight panels
Aluminiumgewindebuchse für den Einsatz definierter Verbindungspunkte in Verbundpanelen. Aluminium threaded insert for settings requested connection points in panels.
MGT-M..-BO-"L"-MTP(O/T) Schutzkappe für Bolzenauf Anfrage Protection caps for boltson request
Schutzkappe für Bolzen, um das Gewinde beim Einlaminieren zu schützen.Protection caps for bolts to protect when laminating.
ANWENDUNGSPRINZIP APPLICATION
Diese Befestiger zeichnen sich durch ihren großen Kopf aus, der beim Einlaminieren die nötige Haltbarkeit im Material bietet. Auch beim Aufkleben bewährt sich ein größerer Flansch, um eine genügend große Klebefläche zu erhalten. Durch die immer geringer werdenden Dicken der Kunststoff- und Verbundstoffteile können hier die nötigen Kräfte übertragen werden.These fasteners are characterized by their big heads which ensure the necessary resistance in the material. When gluing, the big flange offers the advantage to get also bigger gluing surfaces. Due to the reducing thicknesses of materials reque-sted forces can still be held.
21© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEBOLZEN MIT GROSSEM FLANSCHTHREADED BOLTS WITH BIG FLANGE
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BO Bolzen bolt
.. Größe Flansch (rund, quadratisch, rechteckig) size of flange (round, square, rectangular)
L Länge length
ST Material Stahl verzinkt material steel zinc plated
ES Material Edelstahl material stainless steel
BestellbezeichnungBestellbezeichnung: MGT-M..-BO-..-"L"ST(ES)
order description:
Bezeichnung typeGewinde thread
L lxb/T h K
12 15 16 20 25
30
40
50
60 75 100
MGT-M4-BO-1515-"L"ST / ES
M4
x x x x x x x 15x15 1,2 1,2
MGT-M4-BO-19-"L"ST / ES x x x x x x x x x 19 1,2 1,2
MGT-M4-BO-23-"L"ST / ES x x x x x x x x x 23 1,2 1,2
MGT-M4-BO-3030-"L"ST / ES x x x x x x x x x 30x30 1,2 1,2
MGT-M4-BO-3815-"L"ST / ES x x x x x x x x x 38x15 1,2 1,2
MGT-M4-BO-38-"L"ST / ES x x x x x x x x x 38 1,2 1,2
MGT-M5-BO-1515-"L"ST / ES
M5
x x x x x x x x x 15x15 1,2 1,2
MGT-M5-BO-19-"L"ST / ES x x x x x x x x x 19 1,2 1,2
MGT-M5-BO-23-"L"ST / ES x x x x x x x x x 23 1,2 1,2
MGT-M5-BO-3030-"L"ST / ES x x x x x x x x x 30x30 1,2 1,2
MGT-M5-BO-3815-"L"ST / ES x x x x x x x x x 38x15 1,2 1,2
MGT-M5-BO-38-"L"ST / ES x x x x x x x x x 38 1,2 1,2
K
L
hl
b
Tl
>
EIN
LA
MIN
IER
EN
/KL
EB
EN
L
AM
INA
TIN
G/G
LU
ING
22 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
MGT-M6-BO-1515-"L"ST / ES
M6
x x x x x x x x x x * 15x15 1,2 1,2
MGT-M6-BO-19-"L"ST / ES x x x x x x x x x 19 1,2 1,2
MGT-M6-BO-23-"L"ST / ES x x x x x x x x x 23 1,2 1,2
MGT-M6-BO-3030-"L"ST / ES x x x x x x x x x 30x30 1,2 1,2
MGT-M6-BO-3815-"L"ST / ES x x x x x x x x x 38x15 1,2 1,2
MGT-M6-BO-38-"L"ST / ES x x x x x x x x x 38 1,2 1,2
MGT-M6-BO-50-"L"ST / ES x x x x x x x x 50 1,2 1,2
MGT-M8-BO-19-"L"ST / ES
M8
x x x x x x x x x 19 1,5 1,2
MGT-M8-BO-23-"L"ST / ES x x x x x x x x x 23 1,5 1,2
MGT-M8-BO-3030-"L"ST / ES x x x x x x x x x 30x30 1,5 1,2
MGT-M8-BO-3815-"L"ST / ES x x x x x x x x x 38x15 1,5 1,2
MGT-M8-BO-38-"L"ST / ES x x x x x x x x x 38 1,5 1,2
MGT-M8-BO-50-"L"ST / ES x x x x x x x x 50 1,5 1,2
MGT-M10-BO-19-"L"ST / ES
M10
x x x x x x x x x 19 1,5 1,2
MGT-M10-BO-23-"L"ST / ES x x x x x x x x x 23 1,5 1,2
MGT-M10-BO-3030-"L"ST / ES x x x x x x x x x 30x30 1,5 1,2
MGT-M10-BO-3815-"L"ST / ES x x x x x x x x x 38x15 1,5 1,2
MGT-M10-BO-38-"L"ST / ES x x x x x x x x x 38 1,5 1,2
MGT-M10-BO-50-"L"ST / ES x x x x x x x x 50 1,5 1,2
* nur MGT-M6-BO-1515-100ES* only MGT-M6-BO-1515-100ES
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
Bezeichnung typeGewinde thread
L lxb/T h K
12 15 16 20 25
30
40
50
60 75 100
23© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
Bezeichnung type D L lxb/T h K
12 16 20 25
30
40
50
60 75
MGT-4.75-1515-"L"ST
4,75
x x x x x x x x x 15x15 1,2 1,2
MGT-4.75-1515-"L"-ES x x x x x x x x 15x15 1,2 1,2
MGT-4.75-19-"L"ST x x x x x x x x x 19 1,2 1,2
MGT-4.75-19-"L"ES x x x x x x x x 19 1,2 1,2
MGT-4.75-23-"L"ST x x x x x x x x x 23 1,2 1,2
MGT-4.75-23-"L"ES x x x x x x x x 23 1,2 1,2
MGT-4.75-3030-"L"ST x x x x x x x x x 30x30 1,2 1,2
MGT-4.75-3030-"L"ES x x x x x x x x 30x30 1,2 1,2
MGT-4.75-3815-"L"ST x x x x x x x x x 38x15 1,2 1,2
MGT-4.75-3815-"L"ES x x x x x x x x 38x15 1,2 1,2
MGT-4.75-38-"L"ST x x x x x x x x x 38 1,2 1,2
MGT-4.75-38-"L"ES x x x x x x x x 38 1,2 1,2
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
STIFT MIT GROSSEM FLANSCHPIN WITH BIG FLANGE
MGT Material - Gewindeträger Material - Gewindeträger
4.75 Durchmesser diameter
.. Größe Flansch (rund, quadratisch, rechteckig) size of flange (round, square, rectangular)
L Länge length
ST Material Stahl verzinkt material steel zinc plated
ES Material Edelstahl material stainless steel
BestellbezeichnungBestellbezeichnung: MGT-4.75-..-"L"ST(ES)
order description:
K
L
hl
b
Tl
EIN
LA
MIN
IER
EN
/KL
EB
EN
L
AM
INA
TIN
G/G
LU
ING
24 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEBUCHSE MIT GROSSEM FLANSCH, OFFENSTANDOFF WITH BIG FLANGE, OPEN
Bezeichnung typeGewinde thread
L lxb/T K
5 6 10 12 14 15 16 20 22
25
MGT-M4-BU-19-"L"ST
M4
x x x x x x 19 1,2
MGT-M4-BU-19-"L"ES x x x x x 19 1,2
MGT-M4-BU-23-"L"ST x x x x x x 23 1,2
MGT-M4-BU-23-"L"ES x x x x x 23 1,2
MGT-M4-BU-3030-"L"ST x x x x x x 30x30 1,2
MGT-M4-BU-3030-"L"ES x x x x x 30x30 1,2
MGT-M4-BU-3815-"L"ST x x x x x x 38x15 1,2
MGT-M4-BU-3815-"L"ES x x x x x 38x15 1,2
MGT-M4-BU-38-"L"ST x x x x x x 38 1,2
MGT-M4-BU-38-"L"ES x x x x x 38 1,2
MGT-M5-BU-19-"L"ST
M5
x x x x x x 19 1,2
MGT-M5-BU-19-"L"ES x x x x x 19 1,2
MGT-M5-BU-23-"L"ST x x x x x x 23 1,2
MGT-M5-BU-23-"L"ES x x x x x 23 1,2
MGT-M5-BU-3030-"L"ST x x x x x x 30x30 1,2
MGT-M5-BU-3030-"L"ES x x x x x 30x30 1,2
MGT-M5-BU-3815-"L"ST x x x x x x 38x15 1,2
MGT-M5-BU-3815-"L"ES x x x x x 38x15 1,2
MGT-M5-BU-38-"L"ST x x x x x x 38 1,2
MGT-M5-BU-38-"L"ES x x x x x 38 1,2
KL
l
b
T
offen
l
>
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse standoff
.. Größe Flansch (rund, quadratisch, rechteckig) size of flange (round, square, rectangular)
L Länge length
ST Material Stahl verzinkt material steel zinc plated
ES Material Edelstahl material stainless steel
BestellbezeichnungBestellbezeichnung: MGT-M..-BU-..-"L"ST(ES)
order description:
25© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
MGT-M6-BU-19-"L"ST
M6
x x x x x x 19 1,2
MGT-M6-BU-19-"L"ES x x x x x 19 1,2
MGT-M6-BU-23-"L"ST x x x x x x 23 1,2
MGT-M6-BU-23-"L"ES x x x x x 23 1,2
MGT-M6-BU-3030-"L"ST x x x x x x 30x30 1,2
MGT-M6-BU-3030-"L"ES x x x x x 30x30 1,2
MGT-M6-BU-3815-"L"ST x x x x x x 38x15 1,2
MGT-M6-BU-3815-"L"ES x x x x x 38x15 1,2
MGT-M6-BU-38-"L"ST x x x x x x 38 1,2
MGT-M6-BU-38-"L"ES x x x x x 38 1,2
MGT-M6-BU-50-"L"ST x x x 50 1,2
MGT-M6-BU-50-"L"ES x x x 50 1,2
MGT-M8-BU-19-"L"ST
M8
x x x x x x 19 1,2
MGT-M8-BU-19-"L"ES x x x x x 19 1,2
MGT-M8-BU-23-"L"ST x x x x x x 23 1,2
MGT-M8-BU-23-"L"ES x x x x x 23 1,2
MGT-M8-BU-3030-"L"ST x x x x x x 30x30 1,2
MGT-M8-BU-3030-"L"ES x x x x x 30x30 1,2
MGT-M8-BU-3815-"L"ST x x x x x x 38x15 1,2
MGT-M8-BU-3815-"L"ES x x x x x 38x15 1,2
MGT-M8-BU-38-"L"ST x x x x x x 38 1,2
MGT-M8-BU-38-"L"ES x x x x x 38 1,2
MGT-M8-BU-50-"L"ST x x x 50 1,2
MGT-M8-BU-50-"L"ES x x x x 50 1,2
MGT-M10-BU-23-"L"ST
M10
x x x x x x 23 1,2
MGT-M10-BU-23-"L"ES x x x x x 23 1,2
MGT-M10-BU-3030-"L"ST x x x x x x 30x30 1,2
MGT-M10-BU-3030-"L"ES x x x x x 30x30 1,2
MGT-M10-BU-3815-"L"ST x x x x x x 38x15 1,2
MGT-M10-BU-3815-"L"ES x x x x x 38x15 1,2
MGT-M10-BU-38-"L"ST x x x x x x 38 1,2
MGT-M10-BU-38-"L"ES x x x x x 38 1,2
MGT-M10-BU-50-"L"ST x x x 50 1,2
MGT-M10-BU-50-"L"ES x x x 50 1,2
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
Bezeichnung typeGewinde thread
L lxb/T K
5 6 10 12 14 15 16 20 22
25
EIN
LA
MIN
IER
EN
/KL
EB
EN
L
AM
INA
TIN
G/G
LU
ING
26 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEBUCHSE MIT GROSSEM FLANSCH, GESCHLOSSENSTANDOFF WITH BIG FLANGE, CLOSED
>
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse standoff
G geschlossen closed
.. Größe Flansch (rund, quadratisch, rechteckig) size of flange (round, square, rectangular)
L Länge length
ST Material Stahl verzinkt material steel zinc plated
ES Material Edelstahl material stainless steel
BestellbezeichnungBestellbezeichnung: MGT-M..-BU-..-"L"ST(ES)
order description:
KL
l
b
Tl
Bezeichnung typeGewinde thread
L lxb/T K
5 6 10 12 14 15 16 20 22
MGT-M4-BUG-19-"L"ST
M4
x x x x x x 19 1,2
MGT-M4-BUG-19-"L"ES x x x x x 19 1,2
MGT-M4-BUG-23-"L"ST x x x x x x 23 1,2
MGT-M4-BUG-23-"L"ES x x x x x 23 1,2
MGT-M4-BUG-3030-"L"ST x x x x x x 30x30 1,2
MGT-M4-BUG-3030-"L"ES x x x x x 30x30 1,2
MGT-M4-BUG-3815-"L"ST x x x x x x 38x15 1,2
MGT-M4-BUG-3815-"L"ES x x x x x 38x15 1,2
MGT-M4-BUG-38-"L"ST x x x x x x 38 1,2
MGT-M4-BUG-38-"L"ES x x x x x 38 1,2
MGT-M5-BUG-19-"L"ST
M5
x x x x x x 19 1,2
MGT-M5-BUG-19-"L"ES x x x x x 19 1,2
MGT-M5-BUG-23-"L"ST x x x x x x 23 1,2
MGT-M5-BUG-23-"L"ES x x x x x 23 1,2
MGT-M5-BUG-3030-"L"ST x x x x x x 30x30 1,2
MGT-M5-BUG-3030-"L"ES x x x x x 30x30 1,2
MGT-M5-BUG-3815-"L"ST x x x x x x 38x15 1,2
MGT-M5-BUG-3815-"L"ES x x x x x 38x15 1,2
MGT-M5-BUG-38-"L"ST x x x x x x 38 1,2
MGT-M5-BUG-38-"L"ES x x x x x 38 1,2
27© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
MGT-M6-BUG-19-"L"ST
M6
x x x x x x 19 1,2
MGT-M6-BUG-19-"L"ES x x x x x 19 1,2
MGT-M6-BUG-23-"L"ST x x x x x x 23 1,2
MGT-M6-BUG-23-"L"ES x x x x x 23 1,2
MGT-M6-BUG-3030-"L"ST x x x x x x 30x30 1,2
MGT-M6-BUG-3030-"L"ES x x x x x 30x30 1,2
MGT-M6-BUG-3815-"L"ST x x x x x x 38x15 1,2
MGT-M6-BUG-3815-"L"ES x x x x x 38x15 1,2
MGT-M6-BUG-38-"L"ST x x x x x x 38 1,2
MGT-M6-BUG-38-"L"ES x x x x x 38 1,2
MGT-M6-BUG-50-"L"ST x x x 50 1,2
MGT-M6-BUG-50-"L"ES x x x 50 1,2
MGT-M8-BUG-19-"L"ST
M8
x x x x x x 19 1,2
MGT-M8-BUG-19-"L"ES x x x x x 19 1,2
MGT-M8-BUG-23-"L"ST x x x x x x 23 1,2
MGT-M8-BUG-23-"L"ES x x x x x 23 1,2
MGT-M8-BUG-3030-"L"ST x x x x x x 30x30 1,2
MGT-M8-BUG-3030-"L"ES x x x x x 30x30 1,2
MGT-M8-BUG-3815-"L"ST x x x x x x 38x15 1,2
MGT-M8-BUG-3815-"L"ES x x x x x 38x15 1,2
MGT-M8-BUG-38-"L"ST x x x x x x 38 1,2
MGT-M8-BUG-38-"L"ES x x x x x 38 1,2
MGT-M8-BUG-50-"L"ST x x x 50 1,2
MGT-M8-BUG-50-"L"ES x x x 50 1,2
MGT-M10-BUG-23-"L"ST
M10
x x x x x x 23 1,2
MGT-M10-BUG-23-"L"ES x x x x x 23 1,2
MGT-M10-BUG-3030-"L"ST x x x x x x 30x30 1,2
MGT-M10-BUG-3030-"L"ES x x x x x 30x30 1,2
MGT-M10-BUG-3815-"L"ST x x x x x x 38x15 1,2
MGT-M10-BUG-3815-"L"ES x x x x x 38x15 1,2
MGT-M10-BUG-38-"L"ST x x x x x x 38 1,2
MGT-M10-BUG-38-"L"ES x x x x x 38 1,2
MGT-M10-BUG-50-"L"ST x x x 50 1,2
MGT-M10-BUG-50-"L"ES x x x 50 1,2
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
Bezeichnung type Gewinde thread
L lxb/T K
5 6 10 12 14 15 16 20 22
EIN
LA
MIN
IER
EN
/KL
EB
EN
L
AM
INA
TIN
G/G
LU
ING
28 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEMUTTER MIT GROSSEM FLANSCH, OFFENNUT WITH BIG FLANGE, OPEN
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
MU Mutter nut
.. Größe Flansch (rund, quadratisch, rechteckig) size of flange (round, square, rectangular)
ST Material Stahl verzinkt material steel zinc plated
ES Material Edelstahl material stainless steel
BestellbezeichnungBestellbezeichnung: MGT-M..-MU-..-ST(ES)
order description:
Bezeichnung typeGewinde thread
lxb/T K
MGT-M3-MU-19-ST / ES
M3
19 1,2
MGT-M3-MU-23-ST / ES 23 1,2
MGT-M3-MU-3815-ST / ES 38x15 1,2
MGT-M4-MU-19-ST / ES
M4
19 1,2
MGT-M4-MU-23-ST / ES 23 1,2
MGT-M4-MU-3030-ST / ES 30x30 1,2
MGT-M4-MU-3815-ST / ES 38x15 1,2
MGT-M4-MU-38-ST / ES 38 1,2
MGT-M5-MU-19-ST / ES
M5
19 1,2
MGT-M5-MU-23-ST / ES 23 1,2
MGT-M5-MU-3030-ST / ES 30x30 1,2
MGT-M5-MU-3815-ST / ES 38x15 1,2
MGT-M5-MU-38-ST / ES 38 1,2
MGT-M5-MU-50-ST / ES 50 1,2
MGT-M6-MU-19-ST / ES
M6
19 1,2
MGT-M6-MU-23-ST / ES 23 1,2
MGT-M6-MU-3030-ST / ES 30x30 1,2
MGT-M6-MU-3815-ST / ES 38x15 1,2
MGT-M6-MU-38-ST / ES 38 1,2
MGT-M6-MU-50-ST / ES 50 1,2
>
K
l
b
Tl
29© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
MGT-M8-MU-19-ST / ES
M8
19 1,2
MGT-M8-MU-23-ST / ES 23 1,2
MGT-M8-MU-3030-ST / ES 30x30 1,2
MGT-M8-MU-3815-ST / ES 38x15 1,2
MGT-M8-MU-38-ST / ES 38 1,2
MGT-M8-MU-50-ST / ES 50 1,2
MGT-M10-MU-23-ST / ES
M10
23 1,2
MGT-M10-MU-3030-ST / ES 30x30 1,2
MGT-M10-MU-3815-ST / ES 38x15 1,2
MGT-M10-MU-38-ST / ES 38 1,2
MGT-M10-MU-50-ST / ES 50 1,2
MGT-M12-MU-3030-ST / ES
M12
30x30 1,2
MGT-M12-MU-38-ST / ES 38 1,2
MGT-M12-MU-50-ST / ES 50 1,2
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
Bezeichnung typeGewinde thread
lxb/T K
EIN
LA
MIN
IER
EN
/KL
EB
EN
L
AM
INA
TIN
G/G
LU
ING
30 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
GEWINDEMUTTER MIT GROSSEM FLANSCH, GESCHLOSSENNUT WITH BIG FLANGE, CLOSED
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
MU Mutter nut
G geschlossen closed
.. Größe Flansch (rund, quadratisch, rechteckig) size of flange (round, square, rectangular)
ST Material Stahl verzinkt material steel zinc plated
ES Material Edelstahl material stainless steel
BestellbezeichnungBestellbezeichnung: MGT-M..-MU-..-ST(ES)
order description:
>
K
l
b
Tl
Bezeichnung typeGewinde thread
lxb/T K
MGT-M3-MUG-19-ST / ES
M3
19 1,2
MGT-M3-MUG-23-ST / ES 23 1,2
MGT-M3-MUG-3815-ST / ES 38x15 1,2
MGT-M4-MUG-19-ST / ES
M4
19 1,2
MGT-M4-MUG-23-ST / ES 23 1,2
MGT-M4-MUG-3030-ST / ES 30x30 1,2
MGT-M4-MUG-3815-ST / ES 38x15 1,2
MGT-M4-MUG-38-ST / ES 38 1,2
MGT-M5-MUG-19-ST / ES
M5
19 1,2
MGT-M5-MUG-23-ST / ES 23 1,2
MGT-M5-MUG-3030-ST / ES 30x30 1,2
MGT-M5-MUG-3815-ST / ES 38x15 1,2
MGT-M5-MUG-38-ST / ES 38 1,2
MGT-M5-MUG-50-ST / ES 50 1,2
MGT-M6-MUG-19-ST / ES
M6
19 1,2
MGT-M6-MUG-23-ST / ES 23 1,2
MGT-M6-MUG-3030-ST / ES 30x30 1,2
MGT-M6-MUG-3815-ST / ES 38x15 1,2
MGT-M6-MUG-38-ST / ES 38 1,2
MGT-M6-MUG-50-ST / ES 50 1,2
31© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
MGT-M8-MUG-19-ST / ES
M8
19 1,2
MGT-M8-MUG-23-ST / ES 23 1,2
MGT-M8-MUG-3030-ST / ES 30x30 1,2
MGT-M8-MUG-3815-ST / ES 38x15 1,2
MGT-M8-MUG-38-ST / ES 38 1,2
MGT-M8-MUG-50-ST / ES 50 1,2
MGT-M10-MUG-23-ST / ES
M10
23 1,2
MGT-M10-MUG-3030-ST / ES 30x30 1,2
MGT-M10-MUG-3815-ST / ES 38x15 1,2
MGT-M10-MUG-38-ST / ES 38 1,2
MGT-M10-MUG-50-ST / ES 50 1,2
MGT-M12-MUG-3030-ST / ES
M12
30x30 1,2
MGT-M12-MUG-38-ST / ES 38 1,2
MGT-M12-MUG-50-ST / ES 50 1,2
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
Bezeichnung typeGewinde thread
lxb/T K
EIN
LA
MIN
IER
EN
/KL
EB
EN
L
AM
INA
TIN
G/G
LU
ING
32 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
SACKLOCHBUCHSE FÜR VERBUNDPANELECLOSED THREADED INSERT FOR LIGHT WEIGHT PANELS
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
AH Abstandhalter für Verbundplatten spacer for composite panel
V verstärkt strengthened
G geschlossen closed
AL Material Aluminium material aluminium
BestellbezeichnungBestellbezeichnung: MGT-M..-AH(V)G.-..AL
order description:
Bezeichnung typeGewinde thread
L K T1
T2
D D1
l1
MGT-M3-AHG-8.5ALM3
8,5
1,5 11,7
11,7
7,0
2,5
7,5
MGT-M3-AHG-17.5AL 17,5 11,7 10,0
MGT-M4-AHVG-5AL
M4
5,0 15,0 4,5
MGT-M4-AHVG-7AL 7,0 15,0 6,5
MGT-M4-AHG-8.5AL 8,5 11,7 8,0
MGT-M4-AHG-11.5AL 11,5 11,7 10,0
MGT-M4-AHG-17.5AL 17,5 11,7 17,0
MGT-M5-AHVG-5AL
M5
5,0 15,0 4,5
MGT-M5-AHVG-7AL 7,0 15,0 6,5
MGT-M5-AHG-7AL 7,0 11,7 6,5
MGT-M5-AHVG-8.5AL 8,5 15,0 8,0
MGT-M5-AHG-8.5AL 8,5 11,7 8,0
MGT-M5-AHVG-14AL 14,0 15,0 13,5
MGT-M5-AHG-14AL 14,0 11,7 13,5
MGT-M5-AHG-17.5AL 17,5 11,7 17,0
MGT-M6-AHG-11.5AL
M6
11,5 11,7
7,0
10,0
MGT-M6-AHG-17.5AL 17,5 11,7 17,0
MGT-M6-AHG-8.7ST 8,7 11,7 8,2
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
33© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
DURCHGANGSBUCHSE FÜR VERBUNDPANELEINSERT WITHOUT THREAD FOR LIGHT WEIGHT PANELS
MGT Material - Gewindeträger Material - Gewindeträger
.. Nenndurchmesser nominal diameter
AH Abstandhalter für Verbundplatten spacer for composite panel
SK Senkkopf countersunk head
AL Material Aluminium material aluminium
BestellbezeichnungBestellbezeichnung: MGT-..-AH(SK)-..AL
order description:
Bezeichnung typeDurchmesser
nominal diameterL K T
1D D
1
MGT-6.0-AH-8.4AL 6,0 8,4
1,5
11,7 9,0
2,5
MGT-5.5-AHSK-10.2AL
5,5
10,2
13,07,0MGT-5.5-AHSK-12.7AL 12,7
MGT-5.5-AHSK-19AL 19,0
MGT-6.5-AHSK-10.2AL 6,5 10,2 8,0
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
EIN
LA
MIN
IER
EN
/KL
EB
EN
L
AM
INA
TIN
G/G
LU
ING
34 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
WEITERE TYPEN MORE TYPES
Bestellbezeichnungorder description
Seitepage
Beschreibungdescription
Anwendungapplication
MGT-M..- BU(BO)…-Q..
36
auf Anfrageon request
Gewindebuchse oder Gewindebolzen nach Zeichnung oder gewünschten Maßen.Threaded standoff or bolt according to draw-ing or requested measures
MGT-(M)..-..-Q..
36
auf Anfrageon request
Leichtbaubefestiger nach Zeichnung oder gewünschten Maßen.light weight fastener according to drawing or requested measures.
MKT-..
37
auf Anfrageon request
Unterschiedliche Kleber für die Befestigung von Leichtbaubefestigern.Different adhesives for fixation of light weight fasteners.
MBN-..
38
siehe HA-CO-Blindnieten-katalogsee also HA-CO-Blind Rivet catalogue
Blindniete für Kunststoffe und weiche Materialien, wie Gummi und Holz.Blind rivet for polymers and soft materials like rubber and wood.
MGT-M..-MU-"L"MKS
39
Neoprenmutter - Flach-kopf, Rundschaft, mit MessinggewindeeinsatzNeoprene nut - flat head, round shank, with brass rivet nut
Neoprenmutter zum Ausgleichen großer Lochtoleranzen und Überbrückung unter-schiedlicher Wäremausdehnungen von Messing und Thermoplast.Neoprene nut for balancing big hole tole-rances and for securing heat expansion diffe-rences between brass and thermoplasts.
MGT-M..-MUP-"L"ST
40
Spreitzblindnietmutter - Flachkopf, Stahl verzinkt, EdelstahlSoft material rivet nut - flat head, steel - zinc plated, stainless steel
Spreizblindnietmutter für dünne, weiche und spröde Materialien - der Kunststoff wird weder beschädigt noch deformiert.Expanding rivet nut for thin, soft and rigid materials – polymer will not be damaged or deformed.
35© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
WEITERE TYPEN MORE TYPES
Bestellbezeichnungorder description
Seitepage
Beschreibungdescription
Anwendungapplication
MGT-..x..-Type auf Anfrageon request
Schrauben für Thermoplaste, die durch ihr spezielles Design von 30° Flankenwinkel und 8° Steigungswinkel dem Materialfluss des Kunststoffes entgegenkommen.Screws for thermoplasts which favour the flow of the polymer due to their special de-sign of 30° flank angle and 8° gradient angle.
MMW-.. auf Anfrageon request
Tiefziehelemente als Abstandhalter für Thermoplaste, die zur Lochunterstützung eingesetzt werden. Maximale Durchmesser von 65mm.Deep drawing parts as spacers for thermo-plasts, which will be used for hole securing. Maximal diameter of 65mm.
MGT-M..-MUP-"L"AKS auf Anfrageon request
Nylonblindnietmutter für dünne Materialien.Nylon nut used for blind fastening of thin-walled surfaces.
ANWENDUNGSPRINZIP APPLICATION
Blindnieten blind rivetsDer Niet wird in das Mundstück des Verarbeitungswerkzeuges geschoben und dann in das vorbereitete Bohrloch des Werkstückes eingeführt. Bei der Betätigung des Werkzeuges greifen die Klemmbacken den Nietdorn und ziehen mit dem Nagelkopf die Hülse zusammen bis der Dorn an der Sollbruchstelle abreißt.The Mandrel slides into the nosepiece of the tooling and afterwards into the hole of the working piece. During the instal-lation the jaws of the tooling pick up the mandrel and pull the mandrel and the rivet body together. The rivet breakes on the defined breaking point.
Schrauben für Kunststoffe Screws for polymersKunststoffteile werden verschraubt, wenn ein mehrmaliges Öffnen nicht beabsichtigt wird. Speziell ausgelegte Flanken-winkel und hohe Flankenüberdeckungen bieten eine optimale Verschraubung im Kunststoff.Polymer parts will be screwed together when opening just a few times. Special flank angles and high flank overlap ensures high quality in the screwing process.
Abstandhalter SpacersTiefziehteile, je nach Kundenwunsch rund, oval mit Durchmessern bis 65mm, mit oder ohne Gewinde und Längsrändel, mit Höhen bis 100mm in allen tiefziehfähigen Materialien.Deep drawing parts are round, oval with diameters to 65mm, with or without thread and longitudinal knurls, with heights up to 100mm in different deep drawing materials - depending to the customer´s wish.
WE
ITE
RE
TY
PE
N
MO
RE
TY
PE
S
36 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
Je nach Anwendung werden verschiedene Gewindebuchsen oder Gewindebolzen verwendet. Sollten Sie bei den Standardteilen nicht das passende Verbindungselement finden, haben wir die Möglichkeit, Ihnen eine Vielfalt an weiteren Teilen anzubieten. Für Rückfragen können Sie gerne jederzeit unseren technischen Berater kontaktieren. Depending to the application different threaded stand-offs and bolts are used. If you can´t find the perfect part in our standard program, we have the possibility to offer you more fastening parts.If you have further questions, please contact our technical staff.
SONDERTEILE GEWINDEBUCHSE UND GEWINDEBOLZEN SPECIAL PARTS OF NUTS AND THREADED BOLTS
MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
BU Buchse insert
BO Bolzen bolt
BestellbezeichnungBestellbezeichnung: MGT-M..-BU(BO)-..
order description:
SONDERTEILE LEICHTBAUBEFESTIGER SPECIAL LIGHT WEIGHT FASTENER
MGT Material - Gewindeträger Material - Gewindeträger
M mit oder ohne Gewindegröße M.. with or without thread size M..
BestellbezeichnungBestellbezeichnung: MGT-(M)..
order description:
37© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
KLEBER ADHESIVES
Durch Verkleben können Leichtbaubefestiger schnell und effizient montiert werden. Durch die Verklebung vermeidet man eine Schädigung der zu verwendeten Materialien wie z.B. von Carbon, da keine Löcher gebohrt werden müssen.Using adhesives light weight fasteners can be mounted fast and efficient. Damaging of the used materials as carbon can be avoided as there is no need for holes.
Ob man starre oder elastische Verklebungen benötigt, hängt von folgenden Voraussetzungen ab:If there is a need for inelastic or elastic adhesion, depends on the following requirements:
Starres Kleben Inelastic gluing
Elastisches Kleben Elastic gluing
Elastifiziertes KlebenPlasticized gluing
Übertragung von hohen KräftenTransmitting high forces
Übertragung von Kräften bei dynamischen BelastungenTransmitting forces at dynamic loads
vereint die Vorteile beider Klassenadvantages ofboth classes
Eingriffe in die Materialstruktur werden vermiedenInterference in the structure will be avoided
Eingriffe in die Materialstruktur werden vermiedenInterference in the structure will be avoided
Verbindungen unterschiedlichster MaterialkombinationenConnection of different materials
Verbindungen unterschiedlichster MaterialkombinationenConnection of different materials
Ausgleich von Spannungen bei Material-paarungen mit unterschiedlicher thermischer LängenänderungCompensation of tension due to different ther-mal expansion of used materials
Kurze AushärtungszeitenShort cure times
Dicke Klebstoffschichten nötigThick adhesive layers necessary
Für Informationen zu Klebertypen und Gebindegrößen kontaktieren sie unseren technischen Berater. For information concerning adhesive types and sizes, please contact our technical staff.
MKT Material - Klebetechnik Material - Klebetechnik
.. Klebelieferantenbezeichnung Adhesive supplier
BestellbezeichnungBestellbezeichnung: MKT-..
order description:
WE
ITE
RE
TY
PE
N
MO
RE
TY
PE
S
38 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
Bestellbezeichnungorder description
Anwendungapplication
MBN-..- FKS-"L"AST Spreitzniete für Kunststoffe und weiche Materialien, wie Gummi und Holz.Expanding rivet for polymers and soft materials as rubber and wood.
MBN-..-FKP(G)-"L"AAL Presslaschenniete für Kunststoffe, weiche und spröde Materialien.Compression strap rivet for polymers, soft materials and rigid materials.
MBN-..-FK(SK)M-"L"AST(AES/SST/EES) Multigrip Blindniete zur Anwendung bei unterschiedlichen Materialstärken.Multigrip rivet for application with different material thicknesses.
MBN-.. -FKR-"L"AST Gerillte Blindniete zur besseren Verankerung in weichen Materialien.Grooved rivet for better bracing in soft materials.
Weitere Informationen siehe HA-CO-Blindnietenkatalog. More information see also HA-CO-Blind Rivet catalogue.
NIETEN FÜR KUNSTSTOFFE BLIND RIVETS FOR POLYMERS
Bestellbezeichnung: MBN-..-FK..-"L"...
order description:MBN Material - Blindniete Material - Blindniete
.. Nietdurchmesser diameter
FK Flachkopf flat head
SK Senkopf countersunk head
S Spreiztniete expanding rivet
P(G) Presslasche (mit Dichtung) compression strap rivet (with washer)
M Multigrip multigrip
R gerillte Niete grooved rivet
"L" Länge length
AST Hülse/Dorn - Aluminium/Stahl verzinkt sleeve/mandrel - aluminium/steel zinc plated
AAL Hülse/Dorn - Aluminium/Aluminium sleeve/mandrel - aluminium/aluminium
AES Hülse/Dorn - Aluminium/Edelstahl sleeve/mandrel - aluminium/stainless steel
SST Hülse/Dorn - Stahl verzinkt/Stahl verzinkt sleeve/mandrel - steel zinc plated/steel zinc plated
EES Hülse/Dorn - Edelstahl/Edelstahl sleeve/mandrel - stainless steel/stainless steel
39© by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
NEOPRENMUTTER NEOPRENE NUT
Bestellbezeichnung: MGT-M..-MU-"L"MKS
order description:MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
MU Mutter nut
L Länge length
MKS Material Messing Kunststoff material brass rubber
Bezeichnung typeGewinde thread
Klemmbereich
grip
B - Bohrloch-durchmesserhole diameter
T K L
MGT-M3-MU-12.6MKS M3 0,4 - 4,0 8,0 - 8,3 11,0 1,40 12,6 0,25 - 0,50
MGT-M4-MU-12.6MKS M4 0,4 - 4,0 8,0 - 8,3 11,0 1,40 12,6 0,25 - 0,40
MGT-M5-MU-14.1MKS
M5
0,4 - 4,9
9,7 - 9,9
12,70,90
14,1 0,35 - 0,50
MGT-M5-MU-21.5MKS 4,0 - 11,6
14,0
21,5 0,30 - 0,89
MGT-M5-MU-26.1MKS 7,9 - 16,01,30
26,1 0,30 - 0,69
MGT-M5-MU-39.8MKS 20,5 - 30,0 39,8 0,59 - 0,99
MGT-M6-MU-16.0MKS
M6
0,4 - 2,8
12,8 - 13,0
16,0 1,30 16,0 0,59 - 0,99
MGT-M6-MU-21.1MKS 0,8 - 4,7 19,1 4,75 21,1
0,79 - 0,99MGT-M6-MU-26.7MKS 6,4 - 11,5 16,3 2,00 26,7
MGT-M6-MU-35.0MKS 11,5 - 23,0 13,1 - 13,3 16,0 1,30 35,0
MGT-M8-MU-18.3MKS
M8
0,4 - 4,016,0 - 16,2 22,1
3,20 18,3 0,99 - 1,48
MGT-M8-MU-27.9MKS 3,9 - 9,5 5,72 27,90,99 - 1,57
MGT-M8-MU-50.0MKS 15,0 - 39,0 18,1 - 18,3 20,0 1,60 50,0
MGT-M10-MU-55.0MKS M10 19,0 - 40,0 20,1 - 20,3 22,5 1,30 55,0 4,40 - 5,40
MGT-M12-MU-80.0MKS M12 38,0 - 64,0 24,1 - 24,3 27,0 1,30 80,0 5,90 - 6,90
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
AnwendungApplication
WE
ITE
RE
TY
PE
N
MO
RE
TY
PE
S
40 © by HA-CO GmbH • Phone +43 7229 23844 • [email protected] • www.ha-co.at
SPREITZBLINDNIETMUTTER EXPANDING RIVET NUT
Bestellbezeichnung: MGT-M..-MUP-"L"ST(ES)
order description:MGT Material - Gewindeträger Material - Gewindeträger
M Gewindegröße M.. thread size M..
MU Mutter nut
P Einpressen pressing in
L Länge length
ST Material Stahl verzinkt material steel zinc plated
ES Material Edelstahl (1.4301, AISI304) material stainless steel (1.4301, AISI304)
Bezeichnung typeGewinde thread
SB - Bohrloch-durchmesserhole diameter
L
MGT-M4-MUP-17.0STM4
0,4 - 4,88,0
17,00,245 10,0
MGT-M4-MUP-22.0ST 4,8 - 9,5 22,0
MGT-M5-MUP-18.0STM5
0,4 - 4,810,0
18,00,294 14,0
MGT-M5-MUP-23.0ST 4,8 - 9,5 23,0
MGT-M6-MUP-18.0STM6
0,4 - 4,811,0
18,00,343 14,0
MGT-M6-MUP-23.0ST 4,8 - 9,5 23,0
MGT-M8-MUP-25.2ST M8 5,0 - 12,0 14,5 25,2 0,490 28,0
Bezeichnung typeGewinde thread
SB - Bohrloch-durchmesserhole diameter
L
MGT-M5-MUP-18.0ES M5 0,4 - 4,8 10,0 18,0 0,588 16,0
MGT-M6-MUP-23.0ES M6 4,8 - 9,5 11,0 23,0 0,784 22,0
MGT-M8-MUP-25.2ES M8 5,0 - 12,0 15,0 25,2 0,980 28,0
Alle Angaben in mm. Weitere Ausführungen, Abmessungen und Zwischengrößen auf Anfrage.All information stated in mm. Further designs, dimensions and special lengths on request.
AnwendungApplication
BLINDNIETEN, SCHLIESS-RINGBOLZEN
BLIND RIVETS, LOCK BOLTS
BLINDNIETMUTTERN
BLIND RIVET NUTS
SCHWEISSBOLZEN
WELDING STUDS
VERSCHLUSSELEMENTE
LOCKS
DICHTSTOPFEN
SEALING PLUGS
BLRI
EINPRESSBEFESTIGER
SELF CLINCHING FASTENERS
SCHNELLKUPPLUNGEN
QUICK COUPLINGS
LEICHTBAUBEFESTIGER
LIGHTWEIGHT FASTENERS
GEWINDEEINSÄTZE FÜR METALLANWENDUNGEN
THREAD INSERTS FOR METALS
KÄFIGMUTTERN
CAGE NUTS
ALUX-SCHIENENFÜHRUNG
ALUX-GUIDE RAIL
KUPPLUNGEN UND MASCHINENELEMENTE
COUPLINGS AND MACHINE ELEMENTS
BAUGRUPPENMONTAGE, ENGINEERING
MOUNTING THE ASSEMBLY, ENGINEERING
ZENTRALSCHMIERANLAGEN, PUMPEN UND VERTEILER
CENTRAL LUBRICATION SYSTEMS, PUMPS AND DISTRIBUTERS
TELESKOPSCHIENEN
TELESCOPIC SLIDES
PSG LAUFROLLENFÜHRUNG
PSG LINEARMOTION
DREHTEILE, ZEICHNUNGSTEILE
TURNING AND SPECIAL DRAWING PARTS
EINSÄTZE UND GEWINDETRÄGER
INSERTS AND THREADED PARTS
VE