* HOOD PIN HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
CONTACTDE CAPOT
MANDATORY INSTALL | INSTALLATION OBLIGATOIRE Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed. Notice: l'installation des éléments de sécurité est obligatoire. Le contact de capot est un élément de sécurité essentiel et doit absolument être installé.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG
CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
CE MODULE DOIT ÊTRE INSTALLÉ PAR UN TECHNICIEN QUALIFIÉ, TOUTE
ERREUR DANS LES BRANCHEMENTS PEUT OCCASIONNER DES DOMMAGES
PERMANENTS AU VÉHICULE.
STATUT DE CAPOT : LE CONTACT DE CAPOT, DOIT ÊTRE INSTALLÉ SI LE VÉHICULE PEUT DÉMARRER À DISTANCE, LORSQUE LE CAPOT EST OUVERT, PROGRAMMEZ LA FONCTION A11 À NON.
A11 OFFNON
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
ALL REV.: 20200304
ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.COMPATIBLE AVEC VÉHICULE À TRANSMISSION AUTOMATIQUE SEULEMENT.
GUIDE # 72821
Parts required (Not included) Pièce(s) requise(s) (Non incluse(s))
1x Vehicle Key 1x 5Amp Fuse3x 1Amp Diode 1x Relay for key release
1x Clé du véhicule 1x 5Amp Fusible3x Diodes 1Amp 1x Relais pour déblocage de la clé
NOTES
**OEM Remote Monitoring
The vehicles OEM remote will remain functional when the vehicle is running, however, the intelligent access key will not unlock the doors when the vehicle is running.
La télécommande d’origine du véhicule sera fonctionnelle pendant que le véhicule est en marche, toutefois, le déverrouillage des portes par la clé d’accès Intelligente ne sera pas fonctionnel.
ADDENDUM - SUGGESTED WIRING CONFIGURATION
SCHÉMA DE BRANCHEMENT SUGGÉRÉVW
Parts required (not included) Pièces requises (Non incluses)
This manual may change without notice. www.ifar.ca for latest version.
Ce Guide peut faire l'objet de changement sans préavis.www.ifar.ca pour la récente version.
To complete the installation either use one of the existing keys or order a new valet key from Volkswagen, see next page for more information.Pour compléter l'installation utilisez soit une des clés du véhicule ou commandez une clé valet de Volkswagen, voir page suivante pour plus d'information.
1x Vehicle Key 1x Clé du véhicule
ALLE O ALL Page 1 / 5 Rev.20120713 GUIDE #
Date: xx-xx
HARDWARE VERSION : 3 FIRMWARE VERSION : 4.0+
Service No : 000 102 04 2536
INTERFACE MODULE
Made in Canada
PATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
EVO
3 Minimum
HARDWARE VERSIONVERSION DU MATÉRIEL
FIRMWARE VERSIONVERSION DU LOGICIEL
[ ]Minimum0075.
VOLKSWAGEN
To complete the installation either use one of the existing keys or order a new key.
Pour compléter l’installation utilisez soit une des clés du véhicule ou commandez une nouvelle clé.
Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme (fonctionnelles si équipé)
Key
Con
trol
Lock
Unl
ock
Arm
Dis
arm
Tach
omet
er
Trun
k R
elea
se
Doo
r Sta
tus
Trun
k S
tatu
s
Hoo
d S
tatu
s*
Han
d-B
rake
S
tatu
s
Foot
-Bra
ke S
tatu
s
OEM
Rem
ote
mon
itorin
g**
VEHICLEVEHICULES
YEARS ANNÉES
AUDIA4 2015-2016 • • • • • • • • • • • • •
TDI 2015-2016 • • • • • • • • • • • • •Allroad 2015-2016 • • • • • • • • • • • • •
Allroad TDI 2015-2016 • • • • • • • • • • • • •A5 2015-2017 • • • • • • • • • • • • •
TDI 2015-2017 • • • • • • • • • • • • •Q5 2015-2017 • • • • • • • • • • • • •
TDI 2015-2017 • • • • • • • • • • • • •RS5 2015-2017 • • • • • • • • • • • • •
TDI 2015-2017 • • • • • • • • • • • • •S4 2015-2016 • • • • • • • • • • • • • TDI 2015-2016 • • • • • • • • • • • • •S5 2015-2017 • • • • • • • • • • • • •
TDI 2015-2017 • • • • • • • • • • • • •SQ5 2015-2017 • • • • • • • • • • • • •
TDI 2015-2017 • • • • • • • • • • • • •
PUSHSTART
MODEL: EVO-ALLDATE:02/2019FORTIN.CA
SN: 000000 00000
MADE IN CANADA© 2018 ALL RIGHTS RESERVED
2019
COMPATIBLE MODULE
REQUIRED:
QR CODEON THE LABEL FIRMWARE VERSION
VERSION LOGICIELLETo add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
Pour ajouter la version logicielle et les options, utilisez l’outil FLASH LINK UPDATER
ou FLASH LINK MOBILE, vendu séparément.
MANUFACTURED AFTER: 2019
MODULE COMPATIBLE
REQUIS:
CODE QR SUR L’ÉTIQUETTE 60.[08]
FABRIQUÉ APRÈS: 2019 MINIMUM
Page 1 / 9
STAND ALONE INSTALLATION INSTALLATION STAND ALONE
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
NOTES
Program bypass option:Programmez l’option du contournement:
UNIT OPTIONOPTION UNITE DESCRIPTION
C1OEM Remote status (Lock/Unlock) monitoringSuivi des status (Verrouillage/Déverrouil-lage) de la télécommande d’origine
Program bypass option(Vehicle diesel only):
Programmez l’option du contournement(vehicule diesel seulement):
UNIT OPTIONOPTION UNITE DESCRIPTION
D1.3 Diesel mode (Vehicle diesel only)Mode diesel (vehicule diesel seulement)
D6 Push-to-StartPush-to-Start
Program bypass option(If equiped with OEM alarm):
Programmez l’option du contournement(Si équipé d’une alarme d’origine):
UNIT OPTIONOPTION UNITE DESCRIPTION
D2Unlock before / Lock after (Disarm OEM alarm)Déverrouille avant / Verrouille après (Désarme l’alarme d’origine)
Program bypass option IF THE VEHICLE IS NOT EQUIPED
WITH FUNCTIONNAL HOOD PIN:Programmez l’option du contournement
SI LE VÉHICULE N’EST PAS ÉQUIPÉ D’UN CONTACT DE CAPOT FONCTIONNEL:
UNIT OPTIONOPTION UNITE DESCRIPTION
A11 OFFNON
Hood trigger (Output Status).
Contact de capot (état de sortie).
Page 2 / 9
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
PARTS REQUIRED (NOT INCLUDED) | PIÈCES REQUISES (NON INCLUSES)
STAND ALONE CONFIGURATION | CONFIGURATION EN DÉMARREUR AUTONOME
OFF
ON
1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER
1x FLASH LINK MOBILE1x FLASH LINK MOBILE APP
OROU
1x
1x
HOOD PIN
VALET SWITCHCOMMUTATEUR VALET
REMOTE START SAFETY OVERRIDE SWITCH
CONTACTDECAPOT
COMMUTATEUR DE SÉCURITÉ DE DÉSACTIVATION DU DÉMARREUR À DISTANCE
MANDATORY | OBLIGATOIRENotice: the installation of safety elements are mandatory.The hood pin and the valet switch are essential security elements and must be installed.
Notice: l'installation des éléments de sécurité est obligatoire.Le contact de capot et le commutateur de valet sont des éléments de sécurité essentiels et doivent absolument être installés.
Part #: RSPB available, Sold separately.Pièce #: RSPB disponible, vendu séparément.
SOFTWARE | PROGRAMME
Smartphone AndroId or iOS with Internet connection (provider charges may apply).Téléphone Intelligent Android ou iOS avec connection Internet (frais du fournisseur Internet peuvent s’appliquer).
Microsoft Windows Computer with Internet connectionOrdinateur Microsoft Windows avec connection Internet
UN
Program bypass optionOEM Remote Stand Alone Remote Starter:
Programmez l’option du contournementDémarreur à distance Autonome
avec télécommande d’origine :
D1.10D1.1
By default, LOCK, LOCK, LOCKPar défaut, VERROUILLE,VERROUILLE,VERROUILLE
LOCK, UNLOCK, LOCKVERROUILLE,DÉVERROUILLE,VERROUILLE
OUOR
UNIT OPTIONOPTION UNITE DESCRIPTION
UNIT OPTIONOPTION UNITE DESCRIPTION
D4Hybrid mode (Vehicle hybrid only)Mode hybride (vehicule hybride seulement)
Program bypass option with oem remote:Programmez l’option du contournement
avec télécommande d'origine:
UNIT OPTIONOPTION UNITE DESCRIPTION
C1OEM Remote Monitoring
Supervision de la télécommande d'origine
Program bypass option with RF KIT antenna:Programmez l’option du contournement
avec antenne RF:
Program bypass optionVehicle hybrid only:
Programmez l’option du contournementvehicule hybride seulement:
UNIT OPTIONOPTION UNITE DESCRIPTION
H1 to H6H1 à H6
Supported RF Kitsand select RF KitKit RF supportéset sélectionnez le KIT RF
All doors must be closed.
Toutes les portes doivent être fermées
Brake ON No tach Ignition before start
Hood Open
Frein ActivéPas de TachClé de contact détectée avant démarrage Capot Ouvert
REMOTE STARTER DIAGNOSTICSDIAGNOSTIQUE DU DÉMARREUR À DISTANCEMODULE RED LED | DEL ROUGE DU MODULEx2 flash : x3 flash : x4 flash :
x5 flash :
The vehicle will START.
Le véhicule DÉMARRE.
START3XPress the OEM remote’s Lock button 3x to remote-start (or remote-stop) the vehicle.
Appuyez sur le bouton Verrouillage 3X de la télécommande d'origine pour démarrer à distance (ou
arrêter à distance) le véhicule.
REMOTE STARTER FUNCTIONALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE
REMOTE STARTER WARNING CARD | CARTE D'AVERTISSEMENT DE DÉMARREUR À DISTANCE
CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE:or use the package RSPB, Sold separately.
COUPEZ CETTE CARTE D'AVERTISSEMENT ET COLLEZ-LA À UN ENDROIT VISIBLE:ou utilisez la trousse RSPB, vendue séparément.
THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON
ON THE OEM REMOTE 3 TIMES CONSECUTIVELY OR BY A
SMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE
DASHBOARD BEFORE WORKING ON THE VEHICLE.
LE VÉHICULE PEUT DÉMARRER SOIT: EN APPUYANT 3 FOIS CONSÉCUTIVEMENT SUR
LE BOUTON VERROUILLAGE DE LA TÉLÉCOMMANDE DU VÉHICULE OU PAR UN TÉLÉPHONE INTELLIGENT. ACTIONNEZ EN
POSITION ‘ON’ LE COMMUTATEUR DE SÉCURITÉ SITUÉ SOUS LE TABLEAU DE BORD
AVANT LES TRAVAUX D'ENTRETIEN.
DÉMARREUR À DISTANCEREMOTE STARTER
WARNING | ATTENTION
Page 3 / 9
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTION
AT BRAKE SWITCHAU COMMUTATEUR DE FREIN
UNDER STEERING COLUMNTWISTED PAIRSOUS LA COLONNE DE DIRECTIONPAIRE DE FILS TORSADÉS
KEY PORT
REMOVE THE PLASTIC PROTECTIVE CAP OVER THE KEY PORT TO SEE THE WIRE LOCATION. RETIREZ LE CAPUCHON DE PLASTIQUE PROTECTEUR SUR LE DESSUS DU CONNECTEUR POUR VOIR LA POSITION DES FILS.
BRAKE ACTIVATION
(-)START/STOPKEY IN
(-)START/STOP
(-)START/STOP
*AUTOMATIC TRANSMISSION*TRANSMISSION AUTOMATIQUE
(+) 12V*
GROUND
CAN HIGH
CAN LOW
KEY RELEASE
Page 4 / 9
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
Yellow In A1Purple In A2
Purple/White In A3Green Out A4White Out A5
Orange In A6Orange/Black In A7
Dk.Blue In A8Red/Blue In A9
Lt.Blue/Black A10Black Out A11
Pink Out A12Yellow/Black In A13Brown/White Out A14
Pink/Black Out A15Purple/Yellow A16
Green/White A17Green/Red A18
White/Black A19Lt.Blue A20
C5 BrownC4 Gray/Black C3 GrayC2 Orange/BrownC1 Orange/Green
D6 White/RedD5 White/BlueD4 White/GreenD3 Yellow/RedD2 Yellow/BlueD1 Yellow/Green
A C
D
AUTOMATIC TRANSMISSION WIRING CONNECTION | SCHÉMA DE BRANCHEMENT TRANSMISSION AUTOMATIQUE
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11A12A13
A14
A15
A16
A17
A18
A19
A20
C5C4
C3
C2C1
D6D5
D4D3D2D1
A1
D1
D4
C1C2
C5
A18
A17
A14
A12A11
A10
A9
A7
A6
A5
A4
A1
RS1 Ground | MasseRS2 IN 12V Battery(+)
WITH | AVEC DATA-LINK:Direct connectionBranchement directe
RF-KIT REMOTESTARTER
KIT-RF DÉMARREURÀ DISTANCEWITH RF-KIT
AVEC KIT-RF
OPTIONAL RF KITKIT RF OPTIONNEL
B
B4B3B2B1
Cut | Coupez RedCut | Coupez Black
BlueWhite
WITHOUT RF-KIT:SANS KIT RF:
B4 Red 12V Battery(+)B3 Black Ground | Masse
CAN LOWCAN HIGH
(-) Unlock(-) Lock
(-) Lock/Unlock input external control | Contrôle du (-) verrouillage devérrouillage entrée externe
Start / Stop external controlContrôle de démarrage/arrêt externe
Start/Stop external
Hood pin
SAFETY OVERRIDE SWITCHCOMMUTATEUR DE SÉCURITÉ
Hood pin only required on vehicles not equipped with a factory hood pin.Commutateur de capot requis seulement si le véhicule n'est pas équipé de cette composante.
(-)START/STOP
(-)START/STOP
(-)START/STOP
CAN LOW
CAN HIGHKEY IN
C3 C4
Black/RedNoir/Rouge
Grey/BlueGris/Bleu
Black orBlack/BlueNoir ouNoir/Bleu
Grey/YellowGris/Jaune
Orange/BrownOrange/Brun
Orange/GreenOrange/Vert
Black/YellowNoir/Jaune
CU
T
1 2 3 4
9 10 11 12
8
16
5
13
6
14
7
15
GROUND
Back view. 16-pin Black connector. At key port.
Vue de dos. Connecteur Noir 16-pins. Au port de la clé.
At steering columnTwisted pair
À la colonne de directionPaire de �ls torsadés
KEYRELEASE
BrownBrun
BRAKE ACTIVATION
Red/BlackRouge/Noir
1 2 43
(+) 12V
99
Back View - connector White 4-Pin At Brack switch
Vue de dos - connecteur Blanc de 4-pins Au commutateur
de frein
8
Red/GrayRouge/Gris
Key PortMake 3 to 6 loops arround the front of the key Port. Faire 3 à 6 tours autour du devant du contact- démarreur.
Make 5 to 10 loops with a 22 gauge wire arround the valet key. Faire 5 à 10 tours avec un fil de calibre 22 autour de la
clé valet.
5 Amp Fuse
1A D
iode
1A D
iode
1A D
iode
(-)START/STOP
A19
VEHICLEVÉHICULES2009-2010
A19
A20
3086
8587
87a
3086
8587
87a
RS1 or B3
87a
3086
8587
87a 30
Join pin 87 and 85Joindre pin 87 et 85
(+)12V D2
KEY IN
KEY RELEASE
(-)START/STOP
OPTIONAL Idle modeVehicle without start/stop buttonOPTIONEL mode continuVehicule sans bouton démarrage
D3
BRAKE
Convenient Ignition OUT
KEY RAPKEY RAP
Page 5 / 9
The BLUE LED will turn off. La DEL BLEUE s'éteint.
The BLUE LED will flash rapidly.
La DEL BLEU clignotera rapidement.
Wait, Attendre,
PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION
The module is now programmed.
Le module est programmé.
PUSHSTART
Vehicles with key port.Véhicules avec key port.
See next pageVoir prochaine page
1
4
5
6
2
3
Press the key to shut off the ignition.
Appuyez sur la clé pour éteindre l'ignition.
Press and release the programming button once (1x).
Appuyez et relâchez 1 fois le bouton de programmation.
Release the programming button when the LED is BLUE.
If the LED is not solid BLUE, disconnect the 4-Pin connector (Data-Link) and go back to step 1.
Press and hold the programming button:Connect the 4-Pin Data-link connector. The BLUE, RED, YELLOW and BLUE & RED LEDs will alternatively illuminate.
Appuyez et maintenir enfoncé le bouton de programmation: Branchez le connecteur Data-Link à 4-Broches.
Les DELs BLEUE, ROUGE, JAUNE et BLEUE & ROUGE s'allumeront alternativement.
x1HOLD
RELEASE
ON BLUE BLEU
Insert the key into the key port and Press the key to turn ON the ignition.(Do not press the brake pedal)
Insérez la clé dans le port d’allumage et Appuyez sur la clé pour allumer l'ignition.(Ne pas appuyer sur la pédale de frein)
Insert the required remaining connectors.
Insérez les connecteurs requis restants.
Insert Press X1x1PRESS
OFF
x1PRESS
IGNITION ON IGNITION OFF
OFF
x1PRESS
FLASHRAPIDLY
OFF
IGNITION ON PRESS X1
WAIT
ON
Relâchez le bouton de programmation quand la DEL est BLEU.
Si le DEL n'est pas BLEU, débranchez le connecteur4 pins (Data-Link) et allezau début de l'étape 1.
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATIONPage 6 / 9
1
2
3
4
6
5
The module is now programmed.
Le module est programmé.
1
Insert the required remaining connectors.
Do not press the brake pedal.Press the Push-to-Start button twice to turn on the ignition.
Press the Push-to-Start button once to turn off the ignition. The BLUE LED will turn off.
Insérez les connecteurs requis restants.
Ne pas appuyer sur la pédale de frein.Appuyez 2 fois sur le bouton démarrage (Push-to-Start) pour allumer l'ignition.
Appuyez 1 fois sur le bouton démarrage (Push-to-Start) pour éteindre l'ignition. La DEL BLEUE s'éteint.
The BLUE LED will flash rapidly.
La DEL BLEU clignotera rapidement.
Press and release the programming button once (1x).
Appuyez et relâchez 1 fois le bouton de programmation.
Wait, Attendre,
willturn off.
The BLUE LED s'éteint.
La DEL BLEUE
RELEASE
OFF
Release the programming button when the LED is BLUE.
Relâchez le bouton de programmation quand la DEL est BLEU.
If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
Si le DEL n'est pas BLEU débranchez le connecteur 4 pins (Data-Link) et allez au début de l'étape 1.
ON BLUE BLEU
ON ONIGN ON
x2PRESS
IGNITION ONx1PRESS
IGNITION OFF
OFF
Press and hold the programming button:Connect the 4-Pin Data-link connector. The BLUE, RED, YELLOW and BLUE & RED LEDs will alternatively illuminate.
Appuyez et maintenir enfoncé le bouton de programmation: Branchez le connecteur Data-Link à 4-Broches.
Les DELs BLEUE, ROUGE, JAUNE et BLEUE & ROUGE s'allumeront alternativement.
x1HOLD
x1PRESS
FLASHRAPIDLY
OFF
IGNITION ON PRESS X1
WAIT
IGNITION ONIGNITION OFF
ON
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATIONPage 7 / 9
Remote start
Démarrez
the vehicle.
àdistance.
START
All doors mustbe closed.
Toutes lesportes doiventêtre fermées
UNLOCK
Enter
Entrez
the vehiclewith the Intelligent
SmartKey.
dans levéhicule avec laclé intelligente(SmartKey) sur
vous
The vehicle cannow be put in togear and driven.
Vous êtesmaintenant prêt à
embrayer etprendre la route.
Insert
Insérez
the key inthe Key port
la clédans le Key Port
Insert
START
All doors mustbe closed.
Toutes lesportes doiventêtre fermées
UNLOCK
Enter
Entrez
the vehiclewith the Intelligent
SmartKey.
dans levéhicule avec laclé intelligente(SmartKey) sur
vous
The vehicle cannow be put in togear and driven.
Vous êtesmaintenant prêt à
embrayer etprendre la route.
PUSHSTART
Vehicles with key port.Véhicules avec key port.
Vehicles with Push-to-Start.Véhicules avec bouton Push-to-Start.
Unlock the doors with either:
• The OEM remote • The remote-starter
remote.
Déverrouillez les portes avec soit:
• la télécommande d'origine
• la télécomande du démarreur à distance.
Unlock the doors with either:
• The OEM remote • The remote-starter
remote.
Déverrouillez les portes avec soit:
• la télécommande d'origine
• la télécomande du démarreur à distance.
Remote start
Démarrez
the vehicle.
àdistance.
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
REMOTE STARTER FUNCTIONALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCEPage 8 / 9
ALL
MODEL: EVO-ALLDATE:02/2019FORTIN.CA
SN: 000000 00000
MADE IN CANADA© 2018 ALL RIGHTS RESERVED
Module label | Étiquette sur le module
Notice: Updated Firmware and Installation GuidesUpdated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d’installationsDes mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifi ez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit.
WARNINGThe information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifi er tous les fi ls et circuits avant d’effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifi é. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORTTél: 514-255-HELP (4357) 1-877-336-7797
ADDENDUM GUIDEWEB UPDATE | MISE À JOUR INTERNET
www.fortinbypass.com
Page 9 / 9