9MM SUSPENDED ROCK PANNEL MECHANICALLY FIXED TO ALUMINIUM SUPPORTS , ABUTMENT VERTICAL JOINT
REINZINC REVEAL PANNEL RAIN SCREEN FIXED BACK TO 2OOMMCLT WALL WITH Z-BRACKETS WITH INTERMEDIATE ARMADILLOSTRUCTURAL THERMAL BREAKS OR (E/A).
200MM GUTEX VAPOUR PERMEABLE GUTEX IINSUALTION BOARD WITH VAPOUR CONTROLLAYER FIXED TO INSULATION WITH MUSHROOM FIXINGS
VAPOUR PERMEABLE MEMBRANE
KLH 200MM CLT WALL OR (E/A) TO BE INTALLED TO MANUFACTURERS SPECIFICATION.
SA
9MM SUSPENDED ROCK PANNEL MECHANICALLY FIXED TO ALUMINIUM SUPPORTS , ABUTMENT VERTICAL JOINT
SCHUCO THERMALLY BROKEN EXTERNAL GLAZING
GALVINIZED STEEL ANGLE BRACKET
ROCKWOOL OR (E/A) THERMAL INSULATION CAVITY BATT FIRE STOP
VAPOUR PERMEABLE MEMBRANE
57
202
219
30016526
INSECT MESH
75
75
365
50MM SAND BLINDING
NECOFLEX DPM/ RADON OR(E/A) MEMBRANE WRAPPED AROUND INSULATION TO PROTECT FROM MOISTURE PENETRATION.
SA.
SCHUCO DOUBLE GLAZED OR (E/A) CURTAIN WALLING SYSTEM FIXED BACK TO KLH 300X300MM CLT COLUMN WITH GALVINISED STEEL ANGLE BRACKETS
75MM ROAD STONE PERMEABLE PAVING ON 75MM DRAINAGE MATT ON 100MM STONE MIX/AGGRIGATE ON 300MM HARD CORE
200MM KINGSPAN XPS INSULATION OR (E/A)
COMPACFOAM COMPACT FOAM OR (E/A) FIXED TO XPS TO CREATE SURFACE TO BUTT THE BOTTOM TRANSOM OF CURTAIN WALLING AND CONTINUE TO SEAL THE THERMAL ENVELOPE.
100MM STONE MIX/AGGRIGATE ON 300MM HARD CORE
25MM SHERA PLANK FIBRE CEMENT BOARD OR (E/A)STUCK TO DPM WRAPPED COMPACT FOAM
GL
REINZINC REVEAL PANNEL RAIN SCREEN FIXED BACK TO 2OOMMCLT WALL WITH Z-BRACKETS WITH INTERMEDIATE ARMADILLOSTRUCTURAL THERMAL BREAKS OR (E/A).
SCHUCO AWS 120 DOUBLE GLAZEDARGON GAS FILLED ECO WINDOWWITH INTEGRATED SHADING
9MM SUSPENDED ROCK PANNEL MECHANICALLY FIXED TO ALUMINIUM SUPPORTS , ABUTMENT VERTICAL JOINT
SUPREMA CLIP ON POWDER COATED ALUMINIUM ROOF COPING FIXED ON TO INSULATION OR (E/A).
SCHUCO DOUBLE GLAZED OR (E/A) CURTAIN WALLING SYSTEM FIXED BACK TO KLH 300X300MM CLT COLUMN WITH GALVINISED STEEL ANGLE BRACKETS
9MM CRUSHED BASALT ROCK PANNEL RAINSCREEN FIXED TO POWDER COATED ALUMINIUM VERTICAL RAIL FIXED BACKTO POWDER COATED ALUMINIUML-BRACKET WITH INTERMEDIATE THERMAL BREAK OR (E/A).
GLU-LAM BEAM STRUCTURESUPPORTING VIERENDEELCLT WALL STRUCTURE HUNG FROM CLT AUDITORIUM.
Checked byDesigned By Approved By - Date
Project Address/Coordinates
Scale
Project Name
Sheet Name
Rev No Rev Note Date/Time North Checked
1 2 3 4 5 6 7 8 9 10 11 12 13
1 2 3 4 5 6 7 8 9 10 11 12 13
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
Nabil Ghnewa C13470042 DT175 02 2017
Sheet Number
Naul Village Dublin53.586°N 6.290°W
14
LEGEND
GENERAL DESIGN NOTES
KEY PLAN
08/01/2018 21:49:48
As indicated
DT175 TDS MusicCentre Project
DETAIL SHEET 1
A131
NABIL GHNEWA JIM ROCHE JIM ROCHE
JIM ROCHE
1 : 10
CANTILEVER CORNER DETAIL TO 1ST FLOOR
EXTERIOR EAST
1 : 10
SECTION 9 CURTAIN WALL ROCK PANEL DETAIL
1 : 10
GROUND FLOOR FOUNDATION DETAIL
BAUDER BIODIVERSE ROOFPRODUCT SPECIFICATION
POSI GLAZE FRAMELESS GLASSBALUSTRADE GUIDE
KLH CLT SPECIFICATION GUIDE
FIRE PIPE COLLARB150
GUTEX MULTITHERM
ROCK PANNEL INSTALLATION GUIDE
INSULATED SUSPENDED CEILING
RHEINZINK REVEAL PANNEL GUIDE
1
2
3
4
5
6
7
8
CLT TO BE FITTED TO MANUFACTURERS SPECIFICATION UTILISING GLVINIZED STEEL BRACKETS. EACH PANNEL RESTING ON CONCRETEKICKER TO HAVE LAYER ON DPC UNDERNEATH TO PROVENT RISING DAMP FROMENTERING THE STRUCTURE.
GUTEX WALL WOOD FIBRE BOARD
FOLLOWING ON-CENTRE DISTANCES APPLY:40 MM BOARD THICKNESS → MAX. ON-CENTRE IS 62.5 CM60 - 200 MM BOARD THICKNESS → MAX. ON-CENTRE IS 83.5 CM
ALL MEMBRANES ARE TO BE TAPED AND PIPES THAT PUNCTURE THROUGHTHE MEMBRANES ARE TO BE SEALED WITH MANUFACTURERS SUPPLIEDTAPE TO ENSURE CONTINUITY AIR AND WATER TIGHTNESS AT ROOF LEVEL.
ALL PERFERATIONS THROUGH VAPOUR PERMEABLE MEMBRANE ARE TOBE TAPED TO ENSURE INTEGRITY OF MEMBRANE AND VAPOUR DIFFUSION RATE.
WINDOW FRAME TO HAVE PLASTIC THERMAL BREAK PACKER BETWEEN ALUMINIUM FRAME AND CLT WALL TO PREVENT POTENCIAL CONDINSATIONOCCURENCE BETWEEN BOTH MATERIALS WITH WIND PROOF TAPE TO BE APPLIEDTO PREVENT THERMAL BRIDGING.
TAPRED PIR IS TO BE INTALLED TO MANUFACTURERS SPECIFICATION AND AT A FALLOF 1:80.
SUSPENDED ACOUSTIC CEILING PANNELS ARE TO BE HUNG LEVEL IN ACCOURDANCETO MANUFACTURERS SPECIFICATION.
FIRE COLLARS ARE REQUIRED FOR EVERY PIPE THAT MAY PENETRATE A FLOOROR WALL. FIRE COLLARS SUPPLIED WITH DIFFERENT SIZES DEPENDING ON PIPESIZE ARE TO FITTED TO MANUFACURERS SPECIFICATION.
ALUMINIUM RAIN WATER PIPES THAT ARE TAKEN THROUGH THE BUILDING MUST BE INSULATED AND HIDDEN BEHIND THIN CLT WALL TO MAINTAIN CONTINUITYIN THE AESTHETIC EFFECT AND CONTRIBUTE TO THERMAL MASS EFFECT.
WHEN INSTALLING ROCKPANEL BOARDS ONALUMINIUM LOAD-BEARING SECTIONS, FXED POINTS,SLOTTED HOLES AND MOVING POINTS SHOULD BE APPLIED. BY APPLICATIONSOF FXED POINTS AND MOVING POINTS THE FXED POINTS SHOULD BEPRE-DRILLED WITH Ø 5.2 MM, SLOTTED POINTS Ø 5,2 X 8 MM AND THEMOVING POINTS WITH Ø 8 MM. THE SLIDING ATTACHMENT MUST BE DONEWITH A ‘RIVET SPACER’ SO THAT THE ATTACHMENT CAN MOVE EASILY.INSTEAD OF DRILLING FX POINTS AND SLOTTED HOLES ALSO FX-POINT SLEEVESAND SIDE SLEEVES CAN BE USED TO ACHIEVE THE REQUIRED HOLES.CONTACT THE ROCKPANEL GROUP FOR MORE INFORMATION.
PURE VISTA OR (E/A) GLASS BALUSTRADE .
THE MEGAGRIP BASE RAIL SHOULD BE PLACED ONTO ITSDESIGNATED POSITION AND THE HOLES MARKED ON THESUBSTRATE FOR DRILLING. ONCE THE SHOE IS LEVEL INSERTTHE FIXINGS AND TIGHTENED UP TO MAKE THE CHANNELRIGID. THE FIXINGS MUST BE TIGHTENED IN ACCORDANCEWITH THE MANUFACTURERS INSTRUCTIONS.M12 COUNTERSUNK BOLTS MUST BE USED.
AXONIMETRIC 3D EXPRESSING CANTILEVER
N
S
E
W
N
