-
R Commands
• radius-server deadtime, on page 6• radius-server directed-request, on page 7• radius-server host key 0 6 7, on page 8• radius-server host test, on page 10• radius-server key 0 6 7, on page 11• radius-server pss-clean, on page 12• radius-server retransmit, on page 13• radius-server test, on page 14• radius-server timeout, on page 15• random-detect, on page 16• random-detect2 minimum-threshold2 maximum-threshold2, on page 18• random-detect2 non-ecn minimum-threshold2 maximum-threshold2 drop, on page 19• random-detect, on page 20• random-detect cos-based, on page 22• rate-limit, on page 24• rate-limit cpu direction input output both pps action log, on page 25• rate-limit cpu direction input output both pps action log, on page 26• rate-limit packet_in burst, on page 27• rate-limit packet_in burst, on page 28• rate-mode, on page 29• rd, on page 30• rd auto, on page 31• rd auto, on page 32• receiver, on page 33• receiver, on page 34• reconnect-interval, on page 35• record-route, on page 36• record-route, on page 37• record, on page 38• record, on page 39• record, on page 40• record, on page 41• record, on page 42
R Commands1
-
• record netflow-original, on page 43• record netflow, on page 44• record netflow, on page 45• record netflow, on page 46• record netflow protocol-port, on page 47• redistribute bgp, on page 48• redistribute bgp eigrp isis ospf rip static direct amt lisp route-map, on page 49• redistribute filter route-map, on page 50• redistribute filter route-map, on page 51• redistribute maximum-prefix, on page 52• redistribute maximum-prefix, on page 53• redistribute maximum-prefix, on page 54• redistribute maximum-prefix, on page 55• redistribute maximum-prefix, on page 56• redistribute maximum-prefix, on page 57• redistribute route-map, on page 58• redistribute route-map, on page 59• redistribute route-map, on page 60• redistribute route-map, on page 61• redistribute route-map, on page 62• redistribute route-map, on page 63• redistribute route-map, on page 64• redistribute route-map, on page 65• redistribute route-map, on page 66• redistribute route-map, on page 67• redistribute route-map, on page 68• redownload forwarding state, on page 69• redundancy-group, on page 70• reference-bandwidth, on page 71• reference-bandwidth, on page 72• refresh profile, on page 73• register-database-mapping, on page 74• register-route-notifications, on page 75• reload, on page 76• reload cancel, on page 77• reload in, on page 78• reload module, on page 79• reload module force-dnld, on page 80• reload non-interruptive, on page 81• reload power-cycle, on page 82• reload sync-adjacency, on page 83• reload sync-adjacency, on page 84• reload timer, on page 85• reload vdc, on page 86• reload vdc, on page 87• remark, on page 88
R Commands2
R Commands
-
• remark, on page 89• remark, on page 90• remote-as, on page 91• remote-span, on page 92• remote, on page 93• remove-private-as, on page 94• reoptimize events link-up, on page 95• replay-protection, on page 96• report, on page 97• report, on page 98• report, on page 99• report, on page 100• report, on page 101• report, on page 102• report, on page 103• report, on page 104• report, on page 105• report, on page 106• report, on page 107• report, on page 108• report, on page 109• report, on page 110• report, on page 111• report, on page 112• request-data-size, on page 113• request-data-size, on page 114• request-data-size, on page 115• resequence access, on page 116• reset, on page 117• reset, on page 118• reset, on page 119• reset, on page 120• reset, on page 121• reset, on page 122• reset, on page 123• reset, on page 124• reset, on page 125• reset, on page 126• reset, on page 127• reset, on page 128• reset, on page 129• reset, on page 130• reset, on page 131• reset, on page 132• restart amt, on page 133• restart bgp, on page 134
R Commands3
R Commands
-
• restart eigrp, on page 135• restart fabric_mcast, on page 136• restart igmp, on page 137• restart isis, on page 138• restart msdp, on page 139• restart ospf, on page 140• restart ospfv3, on page 141• restart otv-isis, on page 142• restart pim, on page 143• restart pim6, on page 144• restart rip, on page 145• restart rsvp, on page 146• resync-database, on page 147• retain route-target all, on page 148• retain route-target all, on page 149• retransmit-interval, on page 150• retransmit-interval, on page 151• retransmit-interval, on page 152• revision, on page 153• revocation-check crl, on page 154• rewrite-evpn-rt-asn, on page 155• rewrite-rt-asn, on page 156• rfc1583compatibility, on page 157• rip shutdown, on page 158• rmdir, on page 159• rmon alarm absolute rising-threshold falling-threshold, on page 160• rmon event, on page 161• rmon hcalarm absolute startupalarm rising-threshold falling-threshold owner, on page 162• roaming-eid-prefix, on page 163• role feature-group name, on page 164• role name, on page 165• role priority, on page 166• rollback running-config checkpoint, on page 167• root-priority, on page 168• route-map, on page 169• route-map, on page 170• route-map, on page 171• route-map, on page 172• route-map out, on page 173• route-map pbr-statistics, on page 174• route-reflector-client, on page 175• route-reflector-client, on page 176• route-target both, on page 177• route-target both auto, on page 178• route-target both auto, on page 179• route-target export, on page 180
R Commands4
R Commands
-
• route-target export, on page 181• route-target export auto, on page 182• route-target import, on page 183• route-target import, on page 184• route-target import auto, on page 185• route delete dampen interval, on page 186• router-guard ip multicast, on page 187• router-guard ip multicast switchports, on page 188• router-id, on page 189• router-id, on page 190• router-id, on page 191• router-id, on page 192• router-id, on page 193• router-id, on page 194• router-preference maximum, on page 195• router bgp, on page 196• router eigrp, on page 197• router isis, on page 198• router ospf, on page 199• router ospfv3, on page 200• router rip, on page 201• routing-context vrf, on page 202• rsakeypair, on page 203• rtr etr eid, on page 204• rule, on page 205• rule command, on page 206• rule oid, on page 207• run-script, on page 208• run2 guestshell, on page 209• run bash, on page 210
R Commands5
R Commands
-
radius-server deadtime[no] radius-server deadtime
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
duration for which non-reachable server is skippeddeadtime
Length of time, in minutesi0
Command Mode
• /exec/configure
R Commands6
R Commandsradius-server deadtime
-
radius-server directed-request[no] radius-server directed-request
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
enable direct authentication requests to serverdirected-request
Command Mode
• /exec/configure
R Commands7
R Commandsradius-server directed-request
-
radius-server host key 0 6 7{ { [ no ] radius-server host { { key { 0 | 6 | 7 | } [ pac ] [ auth-port [ acct-port ] ] } | { [ auth-port1 ] [ acct-port1 ] } } [ { authentication [ accounting [ timeout ] [ retransmit ] ] } | { [ accounting1 ] [ timeout1 ] [ retransmit1 ] } ] } | { no radius-serverhost key } }
Syntax Description
0key
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
RADIUS server's DNS name or its IP addresshost
IPV4/IPV6 address or DNS namehostipname
RADIUS shared secretkey
(Optional) Secure Radius Enablepac
RADIUS shared secret(clear text)0
RADIUS shared secret(clear text)s0
(Optional) Use for accountingaccounting
(Optional) RADIUS server retransmit countretransmit
(Optional) RADIUS server retransmit counti5
(Optional) RADIUS server timeout period in secondstimeout
(Optional) RADIUS server timeout period in secondsi4
(Optional) RADIUS server retransmit countretransmit1
(Optional) RADIUS server retransmit counti7
(Optional) RADIUS server's port for authenticationauth-port
(Optional) port numberi0
(Optional) RADIUS server timeout period in secondstimeout1
(Optional) RADIUS server timeout period in secondsi6
(Optional) RADIUS server's port for accountingacct-port
(Optional) port numberi1
(Optional) Use for accountingaccounting1
R Commands8
R Commandsradius-server host key 0 6 7
-
(Optional) Use for authenticationauthentication
Radius shared secret(type-6 encrypted)6
Tadius shared secret(encrypted)s6
RADIUS shared secret(encrypted)7
RADIUS shared secret(encrypted)s1
(Optional) RADIUS server's port for authenticationauth-port1
(Optional) port numberi2
RADIUS shared secret(clear text)s2
(Optional) RADIUS server's port for accountingacct-port1
(Optional) port numberi3
Command Mode
• /exec/configure
R Commands9
R Commandsradius-server host key 0 6 7
-
radius-server host test[no] radius-server host { } test { { username { [ password { | 0 | 7 } [idle-time ] ] | [ idle-time ] } } | { password { | 0 | 7 } [ idle-time ] } | { idle-time } }
Syntax Description
username
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
RADIUS server's DNS name or its IP addresshost
IPV4/IPV6 address or DNS namehostipname
Parameters to send test packetstest
user names0
(Optional) user password in test packetspassword
(Optional) user passwords1
(Optional) RADIUS shared secret(clear text)0
(Optional) RADIUS shared secret(clear text)s2
(Optional) RADIUS shared secret(encrypted)7
(Optional) RADIUS shared secret(encrypted)s7
(Optional) time interval for monitoring the serveridle-time
(Optional) time period in minutesi1
Command Mode
• /exec/configure
R Commands10
R Commandsradius-server host test
-
radius-server key 0 6 7{ { [ no ] radius-server key { 0 | 6 | 7 | } } | { no radius-server key } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Global RADIUS server shared secretkey
default RADIUS shared secret(clear text)0
default RADIUS shared secret(clear text)s0
default RADIUS shared secret(type-6 encrypted)6
default RADIUS shared secret(type-6 encrypted)s6
default RADIUS shared secret(encrypted)7
default RADIUS shared secret(encrypted)s1
default RADIUS shared secret(clear text)s2
Command Mode
• /exec/configure
R Commands11
R Commandsradius-server key 0 6 7
-
radius-server pss-clean[no] radius-server pss-clean
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Erase PSSpss-clean
Command Mode
• /exec/configure
R Commands12
R Commandsradius-server pss-clean
-
radius-server retransmit[no] radius-server retransmit
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Global RADIUS server retransmit countretransmit
Global RADIUS server retransmit counti0
Command Mode
• /exec/configure
R Commands13
R Commandsradius-server retransmit
-
radius-server test[no] radius-server test { { username { [ password { | 0 | 7 } [ idle-time ] ] | [idle-time ] } } | { password { | 0 | 7 } [ idle-time ] } | { idle-time } }
Syntax Description
username
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Parameters to send test packetstest
user names0
(Optional) user password in test packetspassword
(Optional) user passwords1
(Optional) RADIUS shared secret(clear text)0
(Optional) RADIUS shared secret(clear text)s2
(Optional) RADIUS shared secret(encrypted)7
(Optional) RADIUS shared secret(encrypted)s7
(Optional) time interval for monitoring the serveridle-time
(Optional) time period in minutesi1
Command Mode
• /exec/configure
R Commands14
R Commandsradius-server test
-
radius-server timeout[no] radius-server timeout
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Global RADIUS server timeout period in secondstimeout
RADIUS server timeout period in secondsi0
Command Mode
• /exec/configure
R Commands15
R Commandsradius-server timeout
-
random-detect[no] random-detect { cos [ minimum-threshold ] { [ packets | bytes | kbytes | mbytes| ms | us ] | percent } [ maximum-threshold ] { [ packets1 | bytes1 |kbytes1 | mbytes1 | ms1 | us1 ] | percent1 } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect
Parameters for each cos valuecos
List of class-of-service valuescos-list
(Optional) Specify minimum threshold for WREDminimum-threshold
(Optional) Specify maximum threshold for WREDmaximum-threshold
Maximum threshold valuemax-thresh
Specify thresholds in percentpercent
Specify thresholds in percentpercent1
Minimum threshold percent of queue sizemin-percent-of-qsize
Maximum threshold percent of queue sizemax-percent-of-qsize
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Milli second(s)ms
(Optional) Micro second(s)us
(Optional) Packetspackets1
(Optional) Bytesbytes1
(Optional) Kilo Byteskbytes1
(Optional) Mega Bytesmbytes1
(Optional) Milli second(s)ms1
(Optional) Micro second(s)us1
Command Mode
R Commands16
R Commandsrandom-detect
-
• /exec/configure/policy-map/type/queuing/class
R Commands17
R Commandsrandom-detect
-
random-detect2 minimum-threshold2 maximum-threshold2[no] random-detect2 minimum-threshold2 { packets2 | bytes2 | kbytes2 | mbytes2 }maximum-threshold2 { packets3 | bytes3 | kbytes3 | mbytes3 } [ drop-probability2 weight2 [ cap-average2 ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect2
Specify minimum threshold for WREDminimum-threshold2
Specify maximum threshold for WREDmaximum-threshold2
Packetspackets2
Bytesbytes2
Kilo Byteskbytes2
Mega Bytesmbytes2
Packetspackets3
Bytesbytes3
Kilo Byteskbytes3
Mega Bytesmbytes3
(Optional) Drop Probability at Maximum Thresholddrop-probability2
(Optional) Drop Probability Valuedrop-prob2
(Optional) Queue length weightweight2
(Optional) Queue length weightweight2
(Optional) If average queue length is more, replace average queue lengthwith current queue length
cap-average2
Command Mode
• /exec/configure/policy-map/type/queuing/class
R Commands18
R Commandsrandom-detect2 minimum-threshold2 maximum-threshold2
-
random-detect2 non-ecn minimum-threshold2maximum-threshold2 drop
[no] random-detect2 non-ecn minimum-threshold2 { packets2 | bytes2 | kbytes2 | mbytes2 }maximum-threshold2 { packets3 | bytes3 | kbytes3 | mbytes3 } { drop-probability2 }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect2
Configure WRED parameters for non-ecnnon-ecn
Specify minimum threshold for WREDminimum-threshold2
Specify maximum threshold for WREDmaximum-threshold2
Packetspackets2
Bytesbytes2
Kilo Byteskbytes2
Mega Bytesmbytes2
Packetspackets3
Bytesbytes3
Kilo Byteskbytes3
Mega Bytesmbytes3
Drop Probability at Maximum Thresholddrop-probability2
Drop Probability Valuedrop-prob2
Command Mode
• /exec/configure/policy-map/type/queuing/class
R Commands19
R Commandsrandom-detect2 non-ecn minimum-threshold2 maximum-threshold2 drop
-
random-detect[no] random-detect [ { minimum-threshold { packets | bytes | kbytes | mbytes }maximum-threshold { packets1 | bytes1 | kbytes1 | mbytes1 } drop-probability weight [ cap-average ] } | threshold { burst-optimized | mesh-optimized } ] [ ecn ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect
(Optional) Thresholdthreshold
(Optional) Threshold optimized for bursty trafficburst-optimized
(Optional) Threshold optimized for mesh trafficmesh-optimized
(Optional) Specify minimum threshold for WREDminimum-threshold
(Optional) Specify maximum threshold for WREDmaximum-threshold
(Optional) Maximum threshold valuemax-thresh
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Packetspackets1
(Optional) Bytesbytes1
(Optional) Kilo Byteskbytes1
(Optional) Mega Bytesmbytes1
(Optional) Drop Probability at Maximum Thresholddrop-probability
(Optional) Drop Probability Valuedrop-prob
(Optional) Queue length weightweight
(Optional) Queue length weightweight
(Optional) If average queue length is more, replace average queue lengthwith current queue length
cap-average
(Optional) ECNecn
Command Mode
R Commands20
R Commandsrandom-detect
-
• /exec/configure/policy-map/type/queuing/class
R Commands21
R Commandsrandom-detect
-
random-detect cos-based[no] random-detect cos-based [ aggregate [ minimum-threshold ] { [ packets | bytes | kbytes |mbytes | ms | us ] | percent } [ maximum-threshold ] { [ packets1 |bytes1 | kbytes1 | mbytes1 | ms1 | us1 ] | percent1 } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect
Configure WRED parameters for cos-based modecos-based
(Optional) ConfigureWREDparameters to same value for all sub-classesaggregate
(Optional) Specify minimum threshold for WREDminimum-threshold
(Optional) Specify maximum threshold for WREDmaximum-threshold
(Optional) Maximum threshold valuemax-thresh
(Optional) Specify thresholds in percentpercent
(Optional) Specify thresholds in percentpercent1
(Optional) Minimum threshold percent of queue sizemin-percent-of-qsize
(Optional) Maximum threshold percent of queue sizemax-percent-of-qsize
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Milli second(s)ms
(Optional) Micro second(s)us
(Optional) Packetspackets1
(Optional) Bytesbytes1
(Optional) Kilo Byteskbytes1
(Optional) Mega Bytesmbytes1
(Optional) Milli second(s)ms1
(Optional) Micro second(s)us1
Command Mode
R Commands22
R Commandsrandom-detect cos-based
-
• /exec/configure/policy-map/type/queuing/class
R Commands23
R Commandsrandom-detect cos-based
-
rate-limitrate-limit { auto | } | no rate-limit
Syntax Description
Negate a command or set its defaultsno
Set the Rate limit for SPAN packetsrate-limit
Set the Rate limit using auto valueauto
Enter the percentage of the maximum rate for SPAN packetsrate_value
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
R Commands24
R Commandsrate-limit
-
rate-limit cpu direction input output both pps action log{ rate-limit cpu direction { input | output | both } pps action log } | { no rate-limit cpu direction [{ input | output | both } pps action log ] }
Syntax Description
Negate a command or set its defaultsno
set packet per second rate limitrate-limit
Supervisor CPU limitscpu
input/output directiondirection
set max input packet rateinput
set max output packet rateoutput
set max input and output packet rateboth
packet per secondpps
pps valuepps-val
log actionaction
write a syslog message if PPS hits rate-limitlog
Command Mode
• /exec/configure
R Commands25
R Commandsrate-limit cpu direction input output both pps action log
-
rate-limit cpu direction input output both pps action log{ rate-limit cpu direction { input | output | both } pps action log } | { no rate-limit cpu direction [{ input | output | both } pps action log ] }
Syntax Description
Negate a command or set its defaultsno
set packet per second rate limitrate-limit
Supervisor CPU limitscpu
input/output directiondirection
set max input packet rateinput
set max output packet rateoutput
set max input and output packet rateboth
packet per secondpps
pps valuepps-val
log actionaction
write a syslog message if PPS hits rate-limitlog
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-eth-any /exec/configure/if-mgmt-config
R Commands26
R Commandsrate-limit cpu direction input output both pps action log
-
rate-limit packet_in burstrate-limit packet_in burst | no rate-limit
Syntax Description
Negate a command or set its defaultsno
OpenFlow rate limit to controllerrate-limit
packet in rate (pps)packet_in
packets per secondpacketin-val
Maximum number of packets to controller (pps)burst
packets per secondburst-val
Command Mode
• /exec/configure/openflow/switch
R Commands27
R Commandsrate-limit packet_in burst
-
rate-limit packet_in burstrate-limit packet_in burst | no rate-limit
Syntax Description
Negate a command or set its defaultsno
OpenFlow rate limit to controllerrate-limit
packet in rate (pps)packet_in
packets per secondpacketin-val
Maximum number of packets to controller (pps)burst
packets per secondburst-val
Command Mode
• /exec/configure/openflow/switch/sub-switch
R Commands28
R Commandsrate-limit packet_in burst
-
rate-moderate-mode [ force ] | no rate-mode [ ] [ force ]
Syntax Description
Negate a command or set its defaultsno
Enter the rate moderate-mode
(Optional) This option will shutdown all ports in port-groupmomentarilyforce
Interface port speedratemode
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
R Commands29
R Commandsrate-mode
-
rd{ rd { | } } | { no rd [ { | } ] }
Syntax Description
Negate a command or set its defaultsno
VPN Route Distinguisherrd
VPN route distinguisher in aa4:nn or ip:nn formatext-comm-rd-aa4nn2
VPN route distinguisher in aa:nn formatext-comm-rd-aa2nn4
Command Mode
• /exec/configure/evpn/evi-sr
R Commands30
R Commandsrd
-
rd auto{ rd { auto | | } } | { no rd [ { auto | | } ] }
Syntax Description
Negate a command or set its defaultsno
VPN Route Distinguisherrd
Generate RD automaticallyauto
VPN route distinguisher in aa4:nn or ip:nn formatext-comm-rd-aa4nn2
VPN route distinguisher in aa:nn formatext-comm-rd-aa2nn4
Command Mode
• /exec/configure/vrf
R Commands31
R Commandsrd auto
-
rd auto{ rd { auto | | } } | { no rd [ { auto | | } ] }
Syntax Description
Negate a command or set its defaultsno
VPN Route Distinguisherrd
Generate RD automaticallyauto
VPN route distinguisher in aa4:nn or ip:nn formatext-comm-rd-aa4nn2
VPN route distinguisher in aa:nn formatext-comm-rd-aa2nn4
Command Mode
• /exec/configure/evpn/evi
R Commands32
R Commandsrd auto
-
receiver[no] receiver
Syntax Description
(Optional) Negate a command or set its defaultsno
Policies for a Local Receiverreceiver
Command Mode
• /exec/configure/nbm-host-policy
R Commands33
R Commandsreceiver
-
receiver[no] receiver
Syntax Description
(Optional) Negate a command or set its defaultsno
Policies for a Local Receiverreceiver
Command Mode
• /exec/configure/nbm-vrf/nbm-host-policy
R Commands34
R Commandsreceiver
-
reconnect-intervalreconnect-interval | no reconnect-interval [ ]
Syntax Description
Negate a command or set its defaultsno
Configure connection reconnect intervalreconnect-interval
Interval in secondsinterval
Command Mode
• /exec/configure/router-bgp/vrf-cmds
R Commands35
R Commandsreconnect-interval
-
record-route[no] record-route
Syntax Description
(Optional) Negate a command or set its defaultsno
Record the route used by the LSPrecord-route
Command Mode
• /exec/configure/te/lsp-attr
R Commands36
R Commandsrecord-route
-
record-route[no] record-route
Syntax Description
(Optional) Negate a command or set its defaultsno
record the route used by the tunnelrecord-route
Command Mode
• /exec/configure/if-te /exec/configure/tunnel-te/cbts-member
R Commands37
R Commandsrecord-route
-
record[no] record
Syntax Description
Record to be monitoredrecord
Record name to be configuredrecordname
Command Mode
• /exec/configure/config-ssx-monitor
R Commands38
R Commandsrecord
-
record[no] record
Syntax Description
Specify INT Record to userecord
Name of recordrecordname
Command Mode
• /exec/configure/config-int-monitor
R Commands39
R Commandsrecord
-
record[no] record
Syntax Description
Specify FTE Record to userecord
Name of recordrecordname
Command Mode
• /exec/configure/config-fte-monitor
R Commands40
R Commandsrecord
-
record[no] record
Syntax Description
Specify Flow Record to userecord
Name of recordrecordname
Command Mode
• /exec/configure/nfm-monitor
R Commands41
R Commandsrecord
-
record[no] record
Syntax Description
Specify Flow Record to userecord
Name of recordrecordname
Command Mode
• /exec/configure/nfm-monitor
R Commands42
R Commandsrecord
-
record netflow-original[no] record netflow-original
Syntax Description
Specify Flow Record to userecord
Traditional IPv4 input NetFlow with origin ASsnetflow-original
Command Mode
• /exec/configure/nfm-monitor
R Commands43
R Commandsrecord netflow-original
-
record netflow[no] record netflow { ipv6 { original-input } }
Syntax Description
Specify Flow Record to userecord
Traditional NetFlow collection schemesnetflow
IPv6 collection schemesipv6
Input NetFloworiginal-input
Command Mode
• /exec/configure/nfm-monitor
R Commands44
R Commandsrecord netflow
-
record netflow[no] record netflow { ipv4 { original-input } }
Syntax Description
Specify Flow Record to userecord
Traditional NetFlow collection schemesnetflow
Traditional IPv4 NetFlow collection schemesipv4
Traditional IPv4 input NetFloworiginal-input
Command Mode
• /exec/configure/nfm-monitor
R Commands45
R Commandsrecord netflow
-
record netflow[no] record netflow { layer2-switched { input } }
Syntax Description
Specify Flow Record to userecord
Traditional NetFlow collection schemesnetflow
Traditional L2 NetFlow collection schemeslayer2-switched
Input NetFlowinput
Command Mode
• /exec/configure/nfm-monitor
R Commands46
R Commandsrecord netflow
-
record netflow protocol-port[no] record netflow protocol-port
Syntax Description
Specify Flow Record to userecord
Traditional NetFlow collection schemesnetflow
Protocol and Ports aggregation schemeprotocol-port
Command Mode
• /exec/configure/nfm-monitor
R Commands47
R Commandsrecord netflow protocol-port
-
redistribute bgp{ redistribute { { bgp } | { eigrp | isis | ospfv3 | rip } | static | direct | amt | lisp } route-map { | } } | { no redistribute { { bgp } | { eigrp | isis | ospfv3 | rip } |static | direct | amt | lisp } [ route-map { | } ] }
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
Enhanced Interior Gateway Protocol (EIGRP)eigrp
ISO Intermediate-to-Intermediate (IS-IS)isis
Open Shortest Path First (OSPFv3)ospfv3
Routing Information Protocol (RIP)rip
Process Tagptag
Staticstatic
Directly connecteddirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Policy to constrain redistributionroute-map
Route-map namepolicy-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
R Commands48
R Commandsredistribute bgp
-
redistribute bgp eigrp isis ospf rip static direct amt lisproute-map
{ redistribute { bgp | { eigrp | isis | ospf | rip } | static | direct | amt | lisp } route-map { | } } | { no redistribute { bgp | { eigrp | isis | ospf | rip } | static| direct | amt | lisp } [ route-map { | } ] }
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
ISO Intermediate-to-Intermediate (IS-IS)isis
Open Shortest Path First (OSPFv2)ospf
Enhanced Interior Gateway Protocol (EIGRP)eigrp
Routing Information Protocol (RIP)rip
Protocol Tagptag
Staticstatic
Directly connecteddirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Policy to constrain redistributionroute-map
Route-map namepolicy-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
R Commands49
R Commandsredistribute bgp eigrp isis ospf rip static direct amt lisp route-map
-
redistribute filter route-map[no] redistribute filter route-map { | }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Filter redistributed routesfilter
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
R Commands50
R Commandsredistribute filter route-map
-
redistribute filter route-map[no] redistribute filter route-map { | }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Filter redistributed routesfilter
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
R Commands51
R Commandsredistribute filter route-map
-
redistribute maximum-prefixredistribute maximum-prefix [ ] [ warning-only | withdraw [ ] ] | no redistribute maximum-prefix [ [ ] [ warning-only | withdraw [ ] ] ]
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Max number of prefixes redistributedmaximum-prefix
max numbermaximum
(Optional) Threshold in %, at which message is generatedthreshold
(Optional) Warning msg is logged when max is reachedwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) No of times to retry to get redist routes againretries
(Optional) Time between the retriestimeout
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv6
R Commands52
R Commandsredistribute maximum-prefix
-
redistribute maximum-prefixredistribute maximum-prefix [ ] [ warning-only | withdraw [ ] ] | no redistribute maximum-prefix [ [ ] [ warning-only | withdraw [ ] ] ]
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Max number of prefixes redistributedmaximum-prefix
max numbermaximum
(Optional) Threshold in %, at which message is generatedthreshold
(Optional) Warning msg is logged when max is reachedwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) No of times to retry to get redist routes againretries
(Optional) Time between the retriestimeout
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv4
R Commands53
R Commandsredistribute maximum-prefix
-
redistribute maximum-prefixredistribute maximum-prefix [ ] [ warning-only | withdraw [ ] ] | no redistribute maximum-prefix [ [ ] [ warning-only | withdraw [ ] ] ]
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Max number of prefixes redistributedmaximum-prefix
max numbermaximum
(Optional) Threshold in %, at which message is generatedthreshold
(Optional) Warning msg is logged when max is reachedwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) No of times to retry to get redist routes againretries
(Optional) Time between the retriestimeout
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
R Commands54
R Commandsredistribute maximum-prefix
-
redistribute maximum-prefix{ redistribute maximum-prefix [ ] [ warning-only | withdraw [ ] ] } | { no redistribute maximum-prefix }
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Maximum number of prefixes redistributed to protocolmaximum-prefix
Maximum number of IP prefixes redistributedmaximum
(Optional) Threshold value (%) at which to generate a warning messagethreshold
(Optional) Log a warning message when limit is exceededwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) Number of times to retry to get the redistributed routes againretries
(Optional) Timeout between each retriestimeout
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
R Commands55
R Commandsredistribute maximum-prefix
-
redistribute maximum-prefixredistribute maximum-prefix [ ] [ warning-only | withdraw [ ] ] | no redistribute maximum-prefix [ [ ] [ warning-only | withdraw [ ] ] ]
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Max number of prefixes redistributedmaximum-prefix
max numbermaximum
(Optional) Threshold in %, at which message is generatedthreshold
(Optional) Warning msg is logged when threshold is reachedwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) Number of attempts to receive redistributed routes after maxis reached
retries
(Optional) Retry intervaltimeout
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
R Commands56
R Commandsredistribute maximum-prefix
-
redistribute maximum-prefix{ redistribute maximum-prefix [ ] [ warning-only | withdraw [ ] ] } | { no redistribute maximum-prefix [ ] [ warning-only | withdraw [ ] ] }
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Maximum number of prefixes redistributed to protocolmaximum-prefix
Maximum number of IP prefixes redistributedmaximum
(Optional) Threshold value (%) at which to generate a warning messagethreshold
(Optional) Log a warning message when limit is exceededwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) Number of times to retry to get the redistributed routes againretries
(Optional) Timeout between each retriestimeout
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
R Commands57
R Commandsredistribute maximum-prefix
-
redistribute route-map[no] redistribute { bgp | { eigrp | isis | ospfv3 | rip } | static | direct | amt } route-map { | }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv6isis
Open Shortest Path First (OSPF) V3ospfv3
Enhanced Interior Gateway Protocoleigrp
RIP for IPv6 (RIPNG)rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv6
R Commands58
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { bgp | { eigrp | isis | ospfv3 | rip } | static | direct | amt | lisp } route-map
Syntax Description
(Optional) Negate a command or set its defaultsno
RIP redistribute routes from other routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Intermediate-to-intermediate (ISIS)isis
Routing Information Protocol (RIP)rip
Open Shortest Path First (OSPFv3)ospfv3
Process tagtag
Static routesstatic
Directly connected routesdirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Policy to constrain redistributionroute-map
Route-map namemap-name
Command Mode
• /exec/configure/router-rip/router-rip-af-ipv6 /exec/configure/router-rip/router-rip-vrf-af-ipv6
R Commands59
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { bgp | { eigrp | isis | ospf | rip } | static | direct | amt | lisp } route-map
Syntax Description
(Optional) Negate a command or set its defaultsno
RIP redistribute routes from other routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Autonomous system numberas
Intermediate-to-intermediate (ISIS)isis
Routing Information Protocol (RIP)rip
Open Shortest Path First (OSPFv2)ospf
Process tagtag
Static routesstatic
Directly connected routesdirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Policy to constrain redistributionroute-map
Route-map namemap-name
Command Mode
• /exec/configure/router-rip/router-rip-af-ipv4 /exec/configure/router-rip/router-rip-vrf-af-ipv4
R Commands60
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { bgp | { eigrp | isis | ospf | rip } | static | direct | amt } route-map { | }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF)ospf
Enhanced Interior Gateway Protocoleigrp
RIP for IPv4rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv4
R Commands61
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { bgp | { eigrp | isis | ospf | rip } | static | direct | amt } route-map { | }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF)ospf
Enhanced Interior Gateway Protocoleigrp
RIP for IPv4rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
R Commands62
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { bgp | { eigrp | isis | ospf | rip } | static | direct | amt | lisp } route-map { | }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF)ospf
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Process tagtag
Static routesstatic
Directly connecteddirect
LISP EID-prefixeslisp
AMT Anycast prefixamt
Route-map to constrain redistributionroute-map
Route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-ipv4
R Commands63
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { bgp | { eigrp | isis | ospfv3 | rip } | static | direct | amt | lisp } route-map { | }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF) V3ospfv3
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Process tagtag
Static routesstatic
Directly connecteddirect
AMT Anycast prefixamt
LISP EID-prefixeslisp
Route-map to constrain redistributionroute-map
Route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-eigrp/router-eigrp-af-ipv6
R Commands64
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { static | direct | amt | lisp | am | hmm | { { eigrp | isis | ospf | rip } } } route-map
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure redistributionredistribute
Static routesstatic
Directly connecteddirect
ISO IS-ISisis
Open Shortest Path First (OSPF)ospf
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Protocoleigrp
AMT anycast prefixamt
LISP EID-prefixes in the non-default VRFlisp
AM routes (learned via ARP)am
HMM prefixhmm
Route-map applied to redistributed routesroute-map
Route-map namermap-name
Source protocol tagtag
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4
R Commands65
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { static | direct | amt | lisp | am | hmm | { { eigrp | isis | ospfv3 | rip } } } route-map
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure redistributionredistribute
Static routesstatic
Directly connecteddirect
ISO IS-ISisis
Open Shortest Path First, version 3 (OSPFv3)ospfv3
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Protocoleigrp
AMT anycast prefixamt
LISP EID-prefixes in the non-default VRFlisp
HMM prefixhmm
AM routes (learned via ARP)am
Route-map applied to redistributed routesroute-map
Route-map namermap-name
Source protocol tagtag
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6
R Commands66
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { bgp | { eigrp | isis | ospf | rip } | static | direct | amt } route-map { | }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF)ospf
Enhanced Interior Gateway Protocoleigrp
RIP for IPv4rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-af-ipv4
R Commands67
R Commandsredistribute route-map
-
redistribute route-map[no] redistribute { bgp | { eigrp | isis | ospfv3 | rip } | static | direct | amt } route-map { | }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv6isis
Open Shortest Path First (OSPF) V3ospfv3
Enhanced Interior Gateway Protocoleigrp
RIP for IPv6 (RIPNG)rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-af-ipv6
R Commands68
R Commandsredistribute route-map
-
redownload forwarding stateredownload forwarding [ ipv4 | ipv6 | all ] state
Syntax Description
redownloadredownload
forwardingforwarding
(Optional) ipv4ipv4
(Optional) ipv6ipv6
(Optional) both ipv4 and ipv6all
statestate
Command Mode
• /exec
R Commands69
R Commandsredownload forwarding state
-
redundancy-group[no] redundancy-group
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a redundancy-group noderedundancy-group
Command Mode
• /exec/configure/if-nve
R Commands70
R Commandsredundancy-group
-
reference-bandwidth[no] reference-bandwidth { [ Mbps ] | Gbps }
Syntax Description
(Optional) Negate a command or set its defaultsno
Change reference bandwidth used for setting interface metricreference-bandwidth
Bandwidth in Mbps (Default)ref-bw-mbps
(Optional) Specify in MbpsMbps
Bandwidth in Gbpsref-bw-gbps
Specify in GbpsGbps
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
R Commands71
R Commandsreference-bandwidth
-
reference-bandwidth[no] reference-bandwidth { [ Mbps ] | Gbps }
Syntax Description
(Optional) Negate a command or set its defaultsno
Change reference bandwidth used for setting interface metricreference-bandwidth
Bandwidth in Mbps (Default)ref-bw-mbps
(Optional) Specify in MbpsMbps
Bandwidth in Gbpsref-bw-gbps
Specify in GbpsGbps
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common /exec/configure/l2mp-isis/l2mp-isis-l2-topo
R Commands72
R Commandsreference-bandwidth
-
refresh profile[no] refresh profile [ overwrite ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Refresh config-profilerefresh
Refresh an applied config-profileprofile
Enter the name of an applied profile as the source profileprofile
Enter the name of an unapplied profile as the destination profiledest-profile
(Optional) Override the source profile with the destination profileoverwrite
Command Mode
• /exec
R Commands73
R Commandsrefresh profile
-
register-database-mapping{ [ no ] register-database-mapping }
Syntax Description
(Optional) Negate a command or set its defaultsno
Register database-mapping EID-prefix to Map-Serverregister-database-mapping
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
R Commands74
R Commandsregister-database-mapping
-
register-route-notifications{ [ no ] register-route-notifications }
Syntax Description
(Optional) Negate a command or set its defaultsno
Register more-specific routes of the database-mapping EID-prefix toMap-Server
register-route-notifications
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
R Commands75
R Commandsregister-route-notifications
-
reloadreload
Syntax Description
reboot the entire boxreload
Command Mode
• /exec
R Commands76
R Commandsreload
-
reload cancelreload cancel
Syntax Description
reboot the entire boxreload
Cancel scheduling of the reloadcancel
Command Mode
• /exec
R Commands77
R Commandsreload cancel
-
reload inreload in
Syntax Description
reboot the entire boxreload
Schedule a reload after some timein
Reload after n secondssecs
Command Mode
• /exec
R Commands78
R Commandsreload in
-
reload modulereload module
Syntax Description
reboot the entire boxreload
reboot a specific modulemodule
please enter the module numbermodule
Command Mode
• /exec
R Commands79
R Commandsreload module
-
reload module force-dnldreload module force-dnld
Syntax Description
reboot the entire boxreload
reboot a specific modulemodule
please enter the module numbermodule
reboot a specific module to force NetBoot and image downloadforce-dnld
Command Mode
• /exec
R Commands80
R Commandsreload module force-dnld
-
reload non-interruptivereload non-interruptive
Syntax Description
reboot the entire boxreload
Reboot without interruptionnon-interruptive
Command Mode
• /exec
R Commands81
R Commandsreload non-interruptive
-
reload power-cyclereload power-cycle
Syntax Description
reboot the entire boxreload
Power cycle ADMpower-cycle
Command Mode
• /exec
R Commands82
R Commandsreload power-cycle
-
reload sync-adjacencyreload sync-adjacency
Syntax Description
reload with sync adjacencyreload
Reload with ARP/ND sync adjacencysync-adjacency
Command Mode
• /exec
R Commands83
R Commandsreload sync-adjacency
-
reload sync-adjacencyreload sync-adjacency
Syntax Description
reboot the entire boxreload
Reload with sync adjacencysync-adjacency
Command Mode
• /exec
R Commands84
R Commandsreload sync-adjacency
-
reload timerreload timer
Syntax Description
reboot the entire boxreload
reboot after a delay secondstimer
delay in secondssecs
Command Mode
• /exec
R Commands85
R Commandsreload timer
-
reload vdcreload vdc
Syntax Description
Restart the current vdcvdc
Power cyclereload
Command Mode
• /exec
R Commands86
R Commandsreload vdc
-
reload vdcreload vdc
Syntax Description
Restart the current vdcvdc
Power cyclereload
Enter Virtual Device Context d-vdc
Command Mode
• /exec
R Commands87
R Commandsreload vdc
-
remark{ [ ] | no } remark
Syntax Description
Negate a command or set its defaultsno
(Optional) Sequence numberseqno
Access list entry commentremark
Comment, up to 100 characterscomment
Command Mode
• /exec/configure/arpacl /exec/configure/timerange
R Commands88
R Commandsremark
-
remark{ [ ] | no } remark
Syntax Description
Negate a command or set its defaultsno
(Optional) Sequence numberseqno
Access list entry commentremark
Comment, up to 100 characterscomment
Command Mode
• /exec/configure/ipacl /exec/configure/ipv6acl
R Commands89
R Commandsremark
-
remark{ [ ] | no } remark
Syntax Description
Negate a command or set its defaultsno
(Optional) Sequence numberseqno
Access list entry commentremark
Comment, up to 100 characterscomment
Command Mode
• /exec/configure/macacl
R Commands90
R Commandsremark
-
remote-as{ remote-as } | { { no | default } remote-as [ ] }
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Specify Autonomous System Number of the neighborremote-as
Autonomous System Numberasn
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
R Commands91
R Commandsremote-as
-
remote-span[no] remote-span
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable remote span VLANremote-span
Command Mode
• /exec/configure/vlan
R Commands92
R Commandsremote-span
-
remoteremote { { ip address { } | hostname } [ port ] [ vrf { | } ] | port | vrf { | } } | no remote { ip address| hostname | port }
Syntax Description
Negate a command or set its defaultsno
Configure remote machine informationremote
Configure IP featuresip
Configure IP addressaddress
Enter ipv4 address informationipaddress
Configure remote host namehostname
Enter name of the remote hosthost_name
(Optional) Configure remote host tcp portport
(Optional) Configure the host tcp port numberport_no
(Optional) vrf via which the vCenter Server is reachablevrf
(Optional) Specify the vrf-namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure/vmt-conn
R Commands93
R Commandsremote
-
remove-private-as[ no | default ] remove-private-as [ all | replace-as ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Remove private AS number from outbound updatesremove-private-as
(Optional) Allall
(Optional) Replacereplace-as
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
R Commands94
R Commandsremove-private-as
-
reoptimize events link-up[no] reoptimize events link-up | no reoptimize timers { delay { cleanup | installation } | frequency } | reoptimizetimers { delay { cleanup | installation } | frequency }
Syntax Description
(Optional) Negate a command or set its defaultsno
Reoptimization parametersreoptimize
Reoptimization triggersevents
Reoptimize tunnels on link up eventslink-up
Reoptimization timerstimers
Delay reoptimization actiondelay
Delay cleanup of reoptimized LSPcleanup
seconds to delay cleanup of replaced tunnel LSPclean_sec
Delay replacement of current LSP by reoptimized LSPinstallation
seconds to delay replacement of tunnel LSPinst_sec
Interval between reoptimization scansfrequency
seconds between reoptimizations (0 disables reoptimization)freq_sec
Command Mode
• /exec/configure/te
R Commands95
R Commandsreoptimize events link-up
-
replay-protection[no] replay-protection
Syntax Description
Enable replay-protection (the default use the no form to disable)replay-protection
Command Mode
• /exec/configure/cts-dot1x /exec/configure/cts-manual
R Commands96
R Commandsreplay-protection
-
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel5
R Commands97
R Commandsreport
-
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel6
R Commands98
R Commandsreport
-
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel7
R Commands99
R Commandsreport
-
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel8
R Commands100
R Commandsreport
-
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel9
R Commands101
R Commandsreport
-
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel10
R Commands102
R Commandsreport
-
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel19
R Commands103
R Commandsreport
-
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/outsel0
R Commands104
R Commandsreport
-
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/outsel1
R Commands105
R Commandsreport
-
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/outsel2
R Commands106
R Commandsreport
-
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel3
R Commands107
R Commandsreport
-
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel4
R Commands108
R Commandsreport
-
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel6
R Commands109
R Commandsreport
-
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel7
R Commands110
R Commandsreport
-
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/outsel0
R Commands111
R Commandsreport
-
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/outsel5
R Commands112
R Commandsreport
-
request-data-size{ { no | default } request-data-size | request-data-size }
Syntax Description
no
Set a command to its defaultsdefault
Request data sizerequest-data-size
Number of bytes in payloadbytes-in-payload
Command Mode
• /exec/configure/ip-sla/icmpEcho
R Commands113
R Commandsrequest-data-size
-
request-data-size{ { no | default } request-data-size | request-data-size }
Syntax Description
no
Set a command to its defaultsdefault
Request data sizerequest-data-size
Number of bytes in payloadbytes-in-payload
Command Mode
• /exec/configure/ip-sla/udp
R Commands114
R Commandsrequest-data-size
-
request-data-size{ { no | default } request-data-size | request-data-size }
Syntax Description
no
Set a command to its defaultsdefault
Request data sizerequest-data-size
Number of bytes in payloadbytes-in-payload
Command Mode
• /exec/configure/ip-sla/jitter
R Commands115
R Commandsrequest-data-size
-
resequence accessresequence { { access-list } | time-range }
Syntax Description
Resequence a list with sequence numbersresequence
IP/IPv6/MAC/ARPip_ipv6_mac_arp
Resequence an access listaccess-list
Resequence a time-rangetime-range
List namename
Starting sequence numbernumber
Step to increment the sequence numberincrement
Command Mode
• /exec/configure
R Commands116
R Commandsresequence access
-
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel9
R Commands117
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel6
R Commands118
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel7
R Commands119
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel8
R Commands120
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel10
R Commands121
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel19
R Commands122
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamtah/outsel0
R Commands123
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamtah/outsel1
R Commands124
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamtah/outsel2
R Commands125
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel3
R Commands126
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel4
R Commands127
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel5
R Commands128
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel6
R Commands129
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel7
R Commands130
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/outsel0
R Commands131
R Commandsreset
-
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/outsel5
R Commands132
R Commandsreset
-
restart amtrestart amt
Syntax Description
Manually restart a componentrestart
Restart the AMT multicast routing protocolamt
Command Mode
• /exec
R Commands133
R Commandsrestart amt
-
restart bgprestart bgp
Syntax Description
Manually restart a componentrestart
Border Gateway Protocol (BGP)bgp
Autonomousas
Command Mode
• /exec
R Commands134
R Commandsrestart bgp
-
restart eigrprestart eigrp
Syntax Description
Manually restart a componentrestart
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Process tageigrp-ptag
Command Mode
• /exec
R Commands135
R Commandsrestart eigrp
-
restart fabric_mcastrestart { fabric_mcast | ngmvpn }
Syntax Description
Manually restart a componentrestart
Restart NGMVPNfabric_mcast
Restart NGMVPNngmvpn
Command Mode
• /exec
R Commands136
R Commandsrestart fabric_mcast
-
restart igmprestart igmp
Syntax Description
Manually restart a componentrestart
Restart the IGMP multicast routing protocoligmp
Command Mode
• /exec
R Commands137
R Commandsrestart igmp
-
restart isisrestart isis
Syntax Description
Manually restart a componentrestart
Intermediate System to Intermediate System (IS-IS)isis
Routing process tagtag
Command Mode
• /exec
R Commands138
R Commandsrestart isis
-
restart msdprestart msdp
Syntax Description
Manually restart a componentrestart
Restart the MSDP multicast routing protocolmsdp
Command Mode
• /exec
R Commands139
R Commandsrestart msdp
-
restart ospfrestart ospf
Syntax Description
Manually restart a componentrestart
Open Shortest Path First (OSPF)ospf
Process tagtag
Command Mode
• /exec
R Commands140
R Commandsrestart ospf
-
restart ospfv3restart ospfv3
Syntax Description
Manually restart a componentrestart
Open Shortest Path First (OSPF) (Version 3)ospfv3
Process tagtag
Command Mode
• /exec
R Commands141
R Commandsrestart ospfv3
-
restart otv-isisrestart otv-isis
Syntax Description
Manually restart a componentrestart
Intermediate System to Intermediate System (IS-IS)otv-isis
Routing process tagtag
Command Mode
• /exec
R Commands142
R Commandsrestart otv-isis
-
restart pimrestart pim
Syntax Description
Manually restart a componentrestart
Restart the PIM multicast routing protocolpim
Command Mode
• /exec
R Commands143
R Commandsrestart pim
-
restart pim6restart pim6
Syntax Description
Manually restart a componentrestart
Restart the PIM6 multicast routing protocolpim6
Command Mode
• /exec
R Commands144
R Commandsrestart pim6
-
restart riprestart rip
Syntax Description
Manually restart a componentrestart
Routing Information Protocol (RIP)rip
Process IDtag
Command Mode
• /exec
R Commands145
R Commandsrestart rip
-
restart rsvprestart rsvp
Syntax Description
Manually restart a processrestart
RSVP processrsvp
Command Mode
• /exec
R Commands146
R Commandsrestart rsvp
-
resync-databaseresync-database
Syntax Description
Re-synchronize switch-profile databaseresync-database
Command Mode
• /exec/configure
R Commands147
R Commandsresync-database
-
retain route-target all[no] retain route-target { all | route-map }
Syntax Description
(Optional) Negate a command or set its defaultsno
Retain the routes based on Target VPN Extended Communitiesretain
Specify Target VPN Extended Communitiesroute-target
All the routes regardless of Target-VPN communityall
Apply route-map to filter routesroute-map
Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-af-l2vpn-vpls
R Commands148
R Commandsretain route-target all
-
retain route-target all[no] retain route-target { all | route-map }
Syntax Description
(Optional) Negate a command or set its defaultsno
Retain the routes based on Target VPN Extended Communitiesretain
Specify Target VPN Extended Communitiesroute-target
All the routes regardless of Target-VPN communityall
Apply route-map to filter routesroute-map
Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6/exec/configure/router-bgp/router-bgp-af-link-state /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn
R Commands149
R Commandsretain route-target all
-
retransmit-interval{ { retransmit-interval } | { no retransmit-interval [ ] } }
Syntax Description
Negate a command or set its defaultsno
Packet retransmission intervalretransmit-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink
R Commands150
R Commandsretransmit-interval
-
retransmit-interval{ { retransmit-interval } | { no retransmit-interval [ ] } }
Syntax Description
Negate a command or set its defaultsno
Packet retransmission intervalretransmit-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink
R Commands151
R Commandsretransmit-interval
-
retransmit-interval{ { retransmit-interval } | { no retransmit-interval [ ] } }
Syntax Description
Negate a command or set its defaultsno
Packet retransmission intervalretransmit-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
R Commands152
R Commandsretransmit-interval
-
revisionrevision | no revision [ ]
Syntax Description
Negate a command or set its defaultsno
Set configuration revision numberrevision
Configuration revision numberrev-id
Command Mode
• /exec/configure/spanning-tree/mst/configuration
R Commands153
R Commandsrevision
-
revocation-check crl[no] revocation-check { crl [ none ] | none }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure trustpoint revocation check methodsrevocation-check
Configure revocation check using crlcrl
(Optional) Configure revocation check using nonenone
Configure revocation check using nonenone
Command Mode
• /exec/configure/trustpoint
R Commands154
R Commandsrevocation-check crl
-
rewrite-evpn-rt-asn[ no | default ] rewrite-evpn-rt-asn
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Auto generate RTs for EBGP neighborrewrite-evpn-rt-asn
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn
R Commands155
R Commandsrewrite-evpn-rt-asn
-
rewrite-rt-asn[ no | default ] rewrite-rt-asn
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Auto generate RTs for EBGP neighborrewrite-rt-asn
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn
R Commands156
R Commandsrewrite-rt-asn
-
rfc1583compatibility[no] rfc1583compatibility
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure 1583 compatibility for external path preferencesrfc1583compatibility
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
R Commands157
R Commandsrfc1583compatibility
-
rip shutdown[no] rip shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
RIP configuration commandsrip
Shutdown RIP on this interfaceshutdown
Command Mode
• /exec/configure/if-igp
R Commands158
R Commandsrip shutdown
-
rmdirrmdir { | }
Syntax Description
Delete a directoryrmdir
Delete a directoryuri0
Delete a directory on expansion flashuri1
Command Mode
• /exec
R Commands159
R Commandsrmdir
-
rmon alarm absolute rising-threshold falling-thresholdrmon alarm { absolute | delta } rising-threshold [ ] falling-threshold [ ][ owner ] | no rmon alarm
Syntax Description
Negate a command or set its defaultsno
Remote Monitoringrmon
Configure an RMON alarmalarm
Alarm numberi0
MIB object to monitors0
Sample intervali1
Test each sample directlyabsolute
Test delta between samplesdelta
Configure the rising thresholdrising-threshold
Rising threshold valuei2
(Optional) Event to fire on rising threshold crossingi3
Configure the falling thresholdfalling-threshold
Falling threshold valuei4
(Optional) Event to fire on falling threshold crossingi5
(Optional) Specify an owner for the alarmowner
(Optional) Alarm owners1
Command Mode
• /exec/configure
R Commands160
R Commandsrmon alarm absolute rising-threshold falling-threshold
-
rmon eventrmon event [ log ] [ trap ] [ description ] [ owner ] | no rmon event
Syntax Description
Negate a command or set its defaultsno
Remote Monitoringrmon
Configure an RMON eventevent
Event numberi0
(Optional) Generate RMON log when the event fireslog
(Optional) Generate SNMP trap when event firestrap
(Optional) SNMP community strings0
(Optional) Specify a description of the eventdescription
(Optional) Event descriptions1
(Optional) Specify an owner for the eventowner
(Optional) Event owners2
Command Mode
• /exec/configure
R Commands161
R Commandsrmon event
-
rmon hcalarm absolute startupalarm rising-thresholdfalling-threshold owner
rmon hcalarm { absolute | delta } startupalarm rising-threshold falling-threshold owner | no rmon hcalarm
Syntax Description
Negate a command or set its defaultsno
Remote Monitoringrmon
Configure an High Capacity RMON alarmhcalarm
Alarm numberi0
MIB object to monitors0
Sample intervali1
Test each sample directlyabsolute
Test delta between samplesdelta
Configure alarm typestartupalarm
Startup alarm type, rising(1) falling(2) risingorfalling(3)i2
Configure the rising thresholdrising-threshold
Rising threshold value in bytesi3
Event to fire on rising threshold crossingi4
Configure the falling thresholdfalling-threshold
Falling threshold value in bytesi5
Event to fire on falling threshold crossingi6
Specify an owner for the alarmowner
Alarm owners1
Command Mode
• /exec/configure
R Commands162
R Commandsrmon hcalarm absolute startupalarm rising-threshold falling-threshold owner
-
roaming-eid-prefix{ [ no ] roaming-eid-prefix { | } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configures what EID-prefixes allowed to roamroaming-eid-prefix
IPv4 roaming EID-prefixeid-prefix
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
R Commands163
R Commandsroaming-eid-prefix
-
role feature-group name[no] role feature-group name
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure rolesrole
Configure role feature-groupfeature-group
Feature-group namename
Enter feature-group namearg6
Command Mode
• /exec/configure
R Commands164
R Commandsrole feature-group name
-
role name[no] role name
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure rolesrole
Enter the role namename
Enter the role namearg2
Command Mode
• /exec/configure
R Commands165
R Commandsrole name
-
role priorityrole priority | no role priority
Syntax Description
Negate a command or set its defaultsno
Role related configurationrole
Configure priority to be used during vPC role (primary/secondary)election
priority
specify priority valuepriority_value
Command Mode
• /exec/configure/vpc-domain
R Commands166
R Commandsrole priority
-
rollback running-config checkpointrollback running-config { checkpoint | file } [ best-effort | stop-at-first-failure |atomic ] [ verbose ]
Syntax Description
Rollback configurationrollback
Rollback running configurationrunning-config
Rollback running configuration to checkpointcheckpoint
Checkpoint namechkpoint_name
Rollback running configuration to configuration filefile
Checkpoint file pathfile_uri
(Optional) Skip errors and proceed with rollbackbest-effort
(Optional) Stop rollback at the first errorstop-at-first-failure
(Optional) Stop rollback and revert to original configuration (default)atomic
(Optional) Show the execution logverbose
Command Mode
• /exec
R Commands167
R Commandsrollback running-config checkpoint
-
root-priority[no] root-priority
Syntax Description
(Optional) Negate a command or set its defaultsno
Set priority with which nodes becomes rootroot-priority
Root priority value per topologyroot-pri
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common /exec/configure/l2mp-isis/l2mp-isis-l2-topo
R Commands168
R Commandsroot-priority
-
route-maproute-map [ permit | deny ]
Syntax Description
Create route-map or enter route-map command moderoute-map
Route-map namertmap-name
(Optional) Route map permits set operationspermit
(Optional) Route map denies set operationsdeny
Sequence to insert to/delete from existing route-map entryseq
Command Mode
• /exec/configure
R Commands169
R Commandsroute-map
-
route-maproute-map [ permit | deny ]
Syntax Description
Create route-map or enter route-map command moderoute-map
Route-map namertmap-name
(Optional) Route map permits set operationspermit
(Optional) Route map denies set operationsdeny
Command Mode
• /exec/configure
R Commands170
R Commandsroute-map
-
route-map[no] route-map { | } [ permit | deny ]
Syntax Description
Negate a command or set its defaultsno
Create route-map or enter route-map command moderoute-map
Route-map namertmap-name
Known route-map namertmap-name
(Optional) Route map permits set operationspermit
(Optional) Route map denies set operationsdeny
Command Mode
• /exec/configure
R Commands171
R Commandsroute-map
-
route-map[no] route-map { | } [ permit | deny ]
Syntax Description
Negate a command or set its defaultsno
Create route-map or enter route-map command moderoute-map
Route-map namertmap-name
Known route-map namertmap-name
(Optional) Route map permits set operationspermit
(Optional) Route map denies set operationsdeny
Sequence to insert to/delete from existing route-map entryseq
Command Mode
• /exec/configure
R Commands172
R Commandsroute-map
-
route-map out[ no | default ] route-map { out | in }
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Apply route-map to neighborroute-map
Route-map namermap-name
Apply policy to outgoing routesout
Apply policy to incoming routesin
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
R Commands173
R Commandsroute-map out
-
route-map pbr-statisticsroute-map pbr-statistics | no route-map { | }pbr-statistics
Syntax Description
Negate a command or set its defaultsno
Create route-map or enter route-map command moderoute-map
Route-map nameroute-map-name
Route-map nameroute-map-name
Known route-map nameroute-map-name
Statistics for policy based routingpbr-statistics
Command Mode
• /exec/configure
R Commands174
R Commandsroute-map pbr-statistics
-
route-reflector-client[ no | default ] route-reflector-client
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure a neighbor as Route reflector clientroute-reflector-client
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls
R Commands175
R Commandsroute-reflector-client
-
route-reflector-client[ no | default ] route-reflector-client
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure a neighbor as Route reflector clientroute-reflector-client
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
R Commands176
R Commandsroute-reflector-client
-
route-target both{ route-target both { | } } | { no route-target both { | } }
Syntax Description
Negate a command or set its defaultsno
Specify Target VPN Extended Communitiesroute-target
Export and Import Target-VPN communityboth
RT extcommunity in aa4:nn or ip:nn formatext-comm-rt-aa4nn2
RT extcommunity in aa:nn formatext-comm-rt-aa2nn4
Command Mode
• /exec/configure/evpn/evi-sr
R Commands177
R Commandsroute-target both
-
route-target both auto{ route-target both { auto | | } } | { no route-target both { auto| | } }
Syntax Description
Negate a command or set its defaultsno
Specify Target VPN Extended Communitiesroute-target
Generate RT automaticallyauto
Export and Import Target-VPN communityboth
RT extcommunity in aa4:nn or ip:nn formatext-comm-rt-aa4nn2
RT extcommunity in aa:nn formatext-comm-rt-aa2nn4
Command Mode
• /exec/configure/evpn/evi
R Commands178
R Commandsroute-target both auto
-
route-target both auto{ route-target both { auto | | } [ evpn | mvpn ] } | { no route-targetboth [ auto [ evpn | mvpn ] | [ evpn | mvpn ] | [ evpn | mvpn] ] }
Syntax Description
Negate a command or set its defaultsno
Specify Target VPN Extended Communitiesroute-target
Export And Import Target-VPN communityboth
Generate route target automaticallyauto
(Optional) Specify Target for EVPN routesevpn