Download - Panoura 18S Assembly Quick Guide
Panoura 18SThree Box Packaging Assembly Quick
Guide
05/0
1/20
23
2ImageWorks Proprietary – Confidential Information
These instructions serve as supplemental assembly guidance of the Panoura. They are not meant to
replace the installation manual, but rather serve to complement it.
If there are any questions, please do not hesitate to contact us
914-592-6100
Summary
05/0
1/20
23
3ImageWorks Proprietary – Confidential Information
1. Packaging Contents2. Install Post3. Hang C-Arm4. Attach Chinrest5. Attach Head Support6. Insert Side Covers7. Insert Center Panel and Mirrors
Agenda
05/0
1/20
23
4ImageWorks Proprietary – Confidential Information
Basic Pan arrives in three boxes containing:1. Post2. C-Arm Assembly, Sensor and Components3. Accessories
1. Package Contents
05/0
1/20
23
5ImageWorks Proprietary – Confidential Information
• Unbox and install the post
• Fasten post to the ground following installation manual (picture below with a base stand).
2. Install Post
05/0
1/20
23
6ImageWorks Proprietary – Confidential Information
Remove box from C-Arm package by removing 4 screws attaching box to skid
3. Hang C-Arm
05/0
1/20
23
7ImageWorks Proprietary – Confidential Information
Remove sensor package
Remove top cover from c-arm by removing 4 screws.
3. Hang C-Arm
05/0
1/20
23
8ImageWorks Proprietary – Confidential Information
Move C-Arm assembly into position in front of post
Remove bolts from c-arm chassis bracket
3. Hang C-Arm
05/0
1/20
23
9ImageWorks Proprietary – Confidential Information
WARNING: Bolts must be fully removed from chassis to prevent damage upon
installation
Remove bolts that fix C-Arm assembly to wooden frame
3. Hang C-Arm
05/0
1/20
23
10ImageWorks Proprietary – Confidential Information
WARNING: Damage can
occur if install is done without moving drive
unit
Move driving unit by rotating coupling of x-axis motor by hand so as not to hit slide body with rotating arm during assembly
3. Hang C-Arm
05/0
1/20
23
11ImageWorks Proprietary – Confidential Information
WARNING: Make sure no cables get caught between post bracket and C-arm assembly
Lift up C-arm assembly and place large hook over mating bracket. Two pins and two tabs fit through mating holes (see next slide)
3. Hang C-Arm
05/0
1/20
23
12ImageWorks Proprietary – Confidential Information
There are two pins and two tabs on the bracket that fit through mating holes in the C-arm assembly.
Pin into slot (x2)
Tab into slot (x2)
3. Hang C-Arm
05/0
1/20
23
13ImageWorks Proprietary – Confidential Information
• Place and tighten four bolts to fasten C-Arm to Post• Pull cable assembly up through hole in C-Arm Chassis,
and make 7 wiring connections (for Pan Unit without ceph)
3. Hang C-Arm
05/0
1/20
23
14ImageWorks Proprietary – Confidential Information
Run Ethernet cable down through same hole. Make sure cable is above the support tray (otherwise front panel will not fit).
Remove panel box on rear of unit and connect Ethernet to port in box. Reattach panel box.
3. Hang C-Arm
05/0
1/20
23
15ImageWorks Proprietary – Confidential Information
Check leveling of the unit following 2.2.4 Leveling in the Installation Manual
Note: In the case of Ceph unit, check the level after installation of the unit as following “2.9 Cephalometric Unit Mounting” in the Installation Manual
3. Hang C-Arm
05/0
1/20
23
16ImageWorks Proprietary – Confidential Information
Attach chinrest assembly over 2 pins and screw to chinrest bracket on post (4 screws).
To attach chinrest assembly, remove 4 bolts from chinrest bracket.
4. Attach Chinrest
05/0
1/20
23
17ImageWorks Proprietary – Confidential Information
Fasten the under panel of the chinrest with the four screws.
Run cables over the chinrest assembly as shown and make connection of cable on the right side. Fix wiring using banding connectors on chinrest assembly.
4. Attach Chinrest
05/0
1/20
23
18ImageWorks Proprietary – Confidential Information
Remove screws on rear left and right of chinrest assembly cover. Place cover and insert screws.
4. Attach Chinrest
05/0
1/20
23
19ImageWorks Proprietary – Confidential Information
Insert and attach underside cover with 5 screws and connect connector
4. Attach Head Support
Remove cap4 screws on the head support fastening bracket
05/0
1/20
23
20ImageWorks Proprietary – Confidential Information
Connect the connector on the head support unit to the connector on the driving part
4. Attach Head Support
05/0
1/20
23
21ImageWorks Proprietary – Confidential Information
Refer to the figure. Put the connector in the connector holder on the head support disc and fasten the head support unit using the 4 screws
NOTE: When mounting the head support unit, make sure that the connector is placed in the connector holder on the head support disc. Beware that the harness is not caught between when the screws are fastened
4. Attach Head Support
05/0
1/20
23
22ImageWorks Proprietary – Confidential Information
Remove left side cover from packaging
5. Insert Side Covers
Make cabling connection to inside of keypad (K1, K3-K7, K2 for Ceph unit)
05/0
1/20
23
23ImageWorks Proprietary – Confidential Information
Fasten left side and right side panels
5. Insert Side Covers
05/0
1/20
23
24ImageWorks Proprietary – Confidential Information
Insert center panel and mirror
Mount eye-ear beam lever
6. Insert Center Panel and Mirror
05/0
1/20
23
25ImageWorks Proprietary – Confidential Information
Continue with standard installation procedure from installation manual