APPROVAL SHEET
ITEM SAW FILTER
Model Name SF-091505-C24
Issued Date 2017.05.23
Revision No 2
Prepared by Confirmed by Approved by
Customer
Dept.
Name
Sign.
SAWNICS
Inc.
Dept. R&D R&D QM
Name JungHwan, Park Namjun, Kim Juwon, Park
Sign.
Approval NEW RENEW Other
Approved Date
112 Seonggeo-Street, Seonggeo-eup, Seobuk-gu, Cheonan-si, Chungcheongnam-do, South Korea / 31044
Tel : +82-41-550-9372 / Fax : +82-41-622-9116 / www.sawnics.com
SAWNICS Inc.
SAWNICS SF-091505-C24 Rev. 2
Page 2 / 15
Revision
No Date Rev No Page Contents
1 2017.02.22. 0 All First issued
2 2017.03.09 1 8 X axis subject added
3 2017.05.23 2 1,4,7,10 Error correcting
SAWNICS SF-091505-C24 Rev. 2
Page 3 / 15
Table of Contents
1. Product Specification 1.1 Model Name
1.2 Scope
1.3 Application
1.4 Maximum Rating
1.5 Electrical Specification
1.6 Frequency Response
1.7 Product Dimension
1.8 Test Fixture
1.9 Marking
1.10 RoHS Information
1.11 Reflow & Solder Recommendation
4 – 8
2.
Reliability Test 2.1 Test Flow
2.2 Test Items & Sample Size
2.3 Test Methods for Electrical Characteristics
9 –10
3. Parts List 3.1 Parts List
10
4. Packing 4.1 Carrier Tape Dimension
4.2 Top Cover Tape Adhesion
4.3 Reel Dimension
4.4 Packaging
11-13
5. Test Results
14
6. Important Notes
15
SAWNICS SF-091505-C24 Rev. 2
Page 4 / 15
1. Product Specification
1.1 Model Name : SF-091505-C24
[SF: SAWNICS / 0915: Center Frequency(MHz) / 05: Serial number / C24: Package type(CSP 1411)]
1.2 Scope : This specification is applied to the Surface Acoustic Wave filter
1.3 Application : RF SAW filter for Wireless, 915.0 MHz
1.4 Maximum Ratings ( Ta = 25℃ )
Parameters Description Rating
Maximum DC Voltage 0 V
Maximum Input Power 10 dBm
Operating Temperature Range -40℃ ~ +85℃
Storage Temperature Range -40℃ ~ +85℃
1.5 Electrical Specification
Item Test Condition Min Typ
@+25°C Max Unit
Center Frequency (Fo) - - 915.0 - MHz
Max.Insertion Loss 902.0 ~ 928.0 MHz - 2.3 3.0 dB
Amplitude Ripple 902.0 ~ 928.0 MHz - 0.9 1.8 dBp-p
VSWR 902.0 ~ 928.0 MHz - 1.8 2.1 -
Source Impedance Unbalanced(1) - 50 -
Load Impedance Unbalanced(1) - 50 -
Attenuation 10.0 ~ 800.0 MHz 42 57 - dB
Attenuation 800.0 ~ 845.0 MHz 40 52 - dB
Attenuation 845.0 ~ 880.0 MHz 35 44 - dB
Attenuation 947.0 ~ 970.0 MHz 13 29 - dB
Attenuation 970.0 ~ 1020.0 MHz 33 45 - dB
Attenuation 1020.0 ~ 1200.0 MHz 35 52 - dB
Notes : (1) No Matching Network (Ref. Testing Environment Circuit as shown below).
SAWNICS SF-091505-C24 Rev. 2
Page 6 / 15
SMITH CHART
1.7 Product Dimension(Unit : mm)
Pin Description
B, C, E Ground
A Input
D Output
SAWNICS SF-091505-C24 Rev. 2
Page 7 / 15
1.8 Test Fixture
Source & Load Impedance: 50 Standard PCB Foot Print(mm)
1.9 Marking
1.10 RoHS Information
SAW FILTER C24-type (CSP-Mold Type : 1.4*1.1*0.65)
n.d. = not detected
Hazardous Materials that MUST be declared Test Method Detection
Limit (ppm)
Amount
(ppm)
Lead – Pb
IEC 62321:2013,ICP
IEC 62321:2008, UV-VIS
IEC 62321:2008, GC-MS
1000 n.d
Mercury - Hg 1000 n.d.
Cadmium - Cd 100 n.d.
Hexavalent Chromium Cr (VI) 1000 n.d.
Polybrominated biphenyls – PBBs 1000 n.d.
Polybrominated diphenyl ethers - PBDE 1000 n.d.
Does this part meet the requirements for a lead free
solder process? (Y/N) Yes
Compiled by: SGS Korea Date :27. Jan. 2016
Marking Descriptions:
S : SAWNICS
j : Band Class
2 : Series Number
X : Date Code(Year+Month)
S j
2 X
SAWNICS SF-091505-C24 Rev. 2
Page 8 / 15
1.11 Reflow & Solder Recommendation
1.11.1 Reflow Profile
(Temperature measured from Reflow-effected Product Surface)
Time
SAWNICS SF-091505-C24 Rev. 2
Page 9 / 15
2. Reliability Test
2.1 Test Flow
Visual Inspection, Dimension Check, Characteristic Inspection (Initial)
Vibration Test Drop Test Thermal Shock
Static Humidity High Temperature
Exposure
Solder Reflow Low Temperature
Exposure
Visual Inspection, Dimension Check, Characteristic Inspection (Final)
2.2 Test item and sample size
NO Test items Criterion N Terms
1 Visual Inspection No Burr, scratch, etc. All
C = 0
2 Dimension Check Specification All
3 Vibration Test Electrical Specification 100
4 Drop Test “ 5
5 Static Humidity “ 15
6 Solder Reflow “ 15
7 Thermal Shock “ 15
8 High Temp. Exposure “ 15
9 Low Temp. Exposure “ 15
Total 180
SAWNICS SF-091505-C24 Rev. 2
Page 10 / 15
2.3 Test Methods for Electrical Characteristics
No Test Item Condition of Test Requirements
1 Vibration
Total peak amplitude = 1.5 mm
Vibration frequency : 10~55 Hz
Sweep period : 1.0 minute
Vibration directions : 3 mutually perpendicular
Duration : 2 hr/direc.
After the test,
Specimen would be
kept at room temperature
for 2 hours.
And then the measured
values shall meet Item 1.5
2 Drop Test Random free drops : 10 times
height = 1.0 meter into concrete floor.(no load)
3 Static Humidity
Temperature : +30℃±2
Relative humidity : 60%
Duration : 96 hours
4 Solder Reflow Temp / Duration : 275℃ / 10sec
Total time : 6min.(IR-reflow)
5 Thermal Shock
Heat cycle conditions
-40℃ (30min) ↔ 85℃ (30min)
*cycle time 100 times
6 High Temperature
Exposure
Temperature : +85±5℃
Duration : 240 hours
7 Low Temperature
Exposure
Temperature : -40±5℃
Duration : 240 hours
3. Parts List
3.1 Material List
No Part name Materials remarks
1 Wafer 42 LT 4 Inch
2 Wire Au-Bump Gold
3 Base LTCC CSP 1.4x1.1
4 Cap Thin Film Mold Type -
5
6
7
8
SAWNICS SF-091505-C24 Rev. 2
Page 11 / 15
F
Bo
AoP1
Po
E
W
Ko
4. Packing
4.1 Carrier Tape Dimension
(Unit : mm)
A B K0 W E F P0 P1
1.30.05 1.650.05 0.750.05 8.00.3 1.750.1 3.50.1 4.00.1 4.00.1
4.2 Top Cover Tape Adhesion
4.2.1 Pull of angle : 0 ~ 15 degree
4.2.2 Speed : 300 mm/min
4.2.3 Force : 0.1 ~ 1.0N
0~15°
Direction of pull off Top cover tape
Carrier tape
SAWNICS SF-091505-C24 Rev. 2
Page 12 / 15
4.3 Reel Dimension
(Unit : mm)
A N H W1 W2
130.5 62 1.0 178.01.0 8.41.0 11.41.0
4.4 Packaging
4.4.1 Tray and Tape Type : N.A
SAWNICS SF-091505-C24 Rev. 2
Page 13 / 15
4.4.2 Packaging Box
1) Inner Box ; in which EECO puts 5 reel which contains
15000 filters.
2) Outer Box ; in which EECO puts 4 inner boxers, that is 20 reel .
Total 60000 filters/outer box
SAWNICS SF-091505-C24 Rev. 2
Page 14 / 15
5. Test Results
Inspected Confirmed Approved
/ / /
1 2 3 4 5 6 7
SAWNICS
SAWNICS
SAWNICS
SAWNICS
SAWNICS
SAWNICS
SAWNICS
SAWNICS
SAWNICS
NO SPEC Insp. 1 2 3 4 5 6 7
SAWNICS
SAWNICS
SAWNICS
3. Appearance SAWNICS
Attenuation
10.0~800.0 MHz
⊙ Etc.
/ /
MARKING
1. Electrical Characteristics ( S - 4 , n = 32 )
1Amplitude Ripple
Confirmed ApprovedSAWNICS
/
Inspected
10
Tested DatasResults
Part No
Quantity
AQL C = 0
RF SAW
Test Items Insp.
800.0~845.0 MHz
902.0~928.0MHz
8
SF-091505-C24
LOT No
SPEC
1020.0~1200.0 MHz
845.0~880.0 MHz min 35㏈
min 35㏈
NO
min 33㏈
min 42㏈
5
6 947.0~970.0 MHz
9
1
3
4
8
2. Dimension ( S - 4 , n = 32 )
Test Items
902.0~928.0MHz
Length
Insertion Loss
MQ-0803-02 (1) SAWNICS Inc.
( G - 1, n = 50 ) Accept, Reject
2
Accept, Reject
(Width)
Length
(Length)
0.65 max3Length
Final Result SAWNICS Accept, Reject
8 Results
9
VSWRmax 2.1
7 970.0~1020.0 MHz
2
min 40㏈
Customer
INSPECTION SHEET
902.0~928.0 MHzmax 1.8㏈
Insp. Date
Model Name
Test Condition
(Height)
Accept, Reject
1.4±0.13㎜
1.1±0.13㎜
9
min 13㏈
10
max 3.0㏈
SAWNICS SF-091505-C24 Rev. 2
Page 15 / 15
6. Important Notes
6.1 This device should not be used in any type of fluid such as water, oil, organic solvent, etc.
6.2 Cleaning agent isopropyl alcohol and ethyl alcohol can be used.
6.3 As rapid temperature change for cleaning after reflow soldering might be a cause of degradation or destruction,
clean this component after confirming that temperature of this component goes down to room temperature.
6.4 As ultrasonic vibration might be a cause of degradation or destruction, do not use ultrasonic cleaning.
6.5 This device follows JEDEC standards for moisture classifications.
The following this device is classified as Moisture Sensitive Level 3
This device is moisture sensitive and need to be handled within proper MSL 3 guidelines to avoid damage from
moisture absorption and exposure to solder reflow temperatures that can result in yield and reliability degradation.
6.6 This is an Electrostatic Sensitive Device.
Please avoid static voltage during operation and storage.
6.7 Sudden change of temperature shall be avoided, deterioration of the characteristics can occur.
6.8 If any malfunction due to designing or manufacturing which is out of specification occurs within one year after
the products have been delivered, the maker should exchange the defective products.