Download - 1. Sawing 1.2 Cutting along grain
24
1. Sawing
SB Dry Wet
Hardwood Softwood Exotic Hardwood Softwood Exotic wood wood 1.2 – 1.4 0.11 – 0.13 0.13 – 0.15 1.4 – 1.8 0.13 – 0.15 0.15 – 0.18 0.10 – 0.12 1.8 – 2.2 0.15 – 0.20 0.18 – 0.25 0.12 – 0.15 2.2 – 2.8 0.20 – 0.25 0.25 – 0.40 0.15 – 0.20 0.20 – 0.30 0.30 – 0.50 0.13 – 0.16 2.8 0.25 – 0.40 0.40 – 0.75 0.20 – 0.40 0.30 – 0.50 0.50 – 1.00 0.16 – 0.25
1.2 Cutting along grain
For splitting or edging timber, for cutting lamellos on horizontal and vertical spindles.
Soft and hardwood, wet, frozen, dry or long-fibre materials.
Edging, single-blade, multi-blade sawblades as well as sawblades with either one or two spindles. Circular saw benches or moulders.
Vf = fz . n . Z/1000
Application
Workpiece material
Machine
Tooth shape
Feed speed [m/min]
FZ (square teeth): For multi-purpose application – particularly suitable for wet and dry wood.
WZ (alternative top bevel teeth):Ideal for long-fibred wood. Higher quality on the exit surface.
TR (trapezoidal teeth)*:Recommended for cutting dry wood with minimum marking.
FZ/TR (square/trapezoidal teeth)*:Ideal for cutting synthetic materials (thermo-plastics).
* An FZ tooth shape is adapted to give the sawblade a TR or FZ/TR tooth shape
Recommended tooth feed rate
fz (in mm)
The tooth feed rate depends on the cutting width; the larger the kerf the higher the possible tooth progression.
25
1. Sawing 1
RPM diagram
����
����
����
����
����
�����
�����
�����
��� ��� ��� ��� ��� �� �����������������
���
���
�� ���Allowable RPM Recommended RPM
�
��
���
���
���
��� ��� ��� ��� �� ���������������
���
Solid wood
Areas of application
Sawblades with wiper teeth
Cutting along grain – the cutting height ae depends on the sawblade diameter D and the workpiece material.
Cutting height diagram
Design External and internal wiper teeth:– For larger cutting heights in wet and dry wood with improved chip clearance.
Internal wiper teeth:– For higher accuracy in dry wood.
External wiper teeth:– Only for sawblades up to a diameter of D = 250 mm.
For cutting solid wood with high tension (twisted fibres) and cutting heights ≥ 40 mm.
Sawblade diameter [mm]
Cut
ting
heig
ht [m
m]
1.2 Cutting along grain
26
1. Sawing
30
40
50
60
70
1.2 < 1.4 1.4 < 1.6 1.8 — 2.01.6 < 1.8
80
1.2 Cutting along grain
Technical notes Recommendations:– Mount thin-kerf sawblades on hydro-sleeves.– Check the sawblade clamping flange diameter.– Check the cutting height and the tooth progression (feed rate).– Resharpen and clean resin residues regularly.
Thin kerf circular sawblades – Cutting height depends on the sawblade cutting width SB.
Cutting height diagram
– Sawmill industry (laminating strips, lumber, etc.).– Solid board production (lamellos and core materials for multiple-layer panels, etc.).– Parquet flooring industry (for core and surface materials, lamellos).– Moulding products (mouldings, lippings, rulers, etc.).– Sport industry (skis, table tennis rackets, etc.).
Thin-kerf sawblades
Application area
– Environmentally friendly use of resources.– Reduced chips and dust.– Optimised timber usage.– More strips from workpiece with standard cuts.
Advantages
Solid wood Cutting width [mm]
Cut
ting
heig
ht [m
m]
To avoid bending the sawblade, we recommend using wide sawblades or hoggers on the motorside. Riving knives are recommended when cutting thin lamella; mounting a split machine table is necessary.
Machine types
Single or multi-spindle multi-blade
machines without automatic feed
Single or multi-spindle multi-blade Multi-spindle machines
machines without automatic feed with automatic feed
Thin-kerf circular sawblades Ultra-thin circular sawblades D mm 200 – 300 > 300 – 500 180 – 250 SB mm 1.8 – 2.8 2.8 – 3.6 1.2 – 2.0
27
1. Sawing 11.2 Cutting along grain
Position of double keyways
for spiral arrangement of the
circular sawblades
��� ������
�� ��
�����
The machine saw spindle should have high precision bearings for accuracy.
Precise and stable feeding devices needed for bent, curved or twisted materials. – Accurate adjustment of the spindle and guide needed to guarantee guiding when
sawing vertically (top and bottom side spindles).
– For horizontal cutting, the thickness of riving knives depends on the cutting width of the sawblades. They must be aligned 100% horizontal.
Multi-spindle machines with
automatic feed (for horizontal
and vertical cutting)
1/3 of the tooth pitch 2/3 of the tooth pitch
2 ● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.1 Circular sawblades with wiper teeth
SB
TDISW
FZ
Sawblade with interior & exterior wiper teeth
Application:
For cutting along grain - shoulder kerfs and square cuts
Machine:
Straight line edger, single-blade, multi-blade as well as single-spindle and double-spindle circular saw benches.
Workpiece material:
Softwood and hardwood wet, frozen, dry and long-fibred (poplar, balsa etc.) up to130 mm cutting height.
Technical information:
With two internal and external wiper teeth (over D-280 mm). Large lateral tooth overhang for cuts in wet and frozen wood.
Square cut and shoulder kerf
WK 100-2-43
Machine Dmm
SBmm
TDImm
BOmm
BOmax.mm
DKNmm
FLDmax.mm
Z ZF SWDegree
ID
250 4,4 2,8 30 80 130 18 FZ 25 067000 ●
300 5,0 3,2 30 80 130 20 FZ 25 067001 ●
Raimann 300 5,0 3,2 80 23/90 110 20 FZ 25 067003 ▫
350 5,0 3,2 30 100 130 24 FZ 25 067004 ●
380 5,0 3,2 30 100 140 24 FZ 25 067044 ●
380 5,0 3,2 80 140 24 FZ 25 067045 ▫
400 5,0 3,2 30 120 150 28 FZ 25 067005 ●
450 5,0 3,2 30 120 160 24 FZ 25 067026 ●
SB
TDISW
FZ
Application:
For cutting along grain - medium kerfs
Medium kerf
WK 100-2-43
Machine Dmm
SBmm
TDImm
BOmm
BOmax.mm
DKNmm
FLDmax.mm
Z ZF SWDegree
ID
250 3,5 2,2 30 80 130 18 FZ 25 067006 ●
300 3,5 2,2 30 80 110 20 FZ 25 067024 ●
Raimann 300 3,5 2,2 70 21/83 110 20 FZ 25 067008 ●
RaimannCostaStorti
300 3,5 2,2 80 23/9013/8913/89
110 20 FZ 25 067029 ●
300 3,5 2,2 80 13/8913/89
140 20 FZ 25 067046 ●
350 4,0 2,8 30 100 130 24 FZ 25 067015 ●
380 4,0 2,8 30 100 140 24 FZ 25 067047 ●
380 4,0 2,8 80 19/8919/89
140 24 FZ 25 067048 ▫
400 4,0 2,8 30 120 140 20 FZ 25 067049 ●
400 4,0 2,8 30 120 150 28 FZ 25 067030 ●
450 4,4 3,0 30 120 160 24 FZ 25 067031 ●
28
Dmm
SBmm
TDImm
BOmm
BOmax.mm
DKNmm
Z ZF SWDegree
ID
250 3,2 2,2 70 20,6/83 20 WZ 18 068750 ●
300 3,2 2,2 70 80 20,6/83 24 WZ 18 068751 ●
320 3,2 2,2 70 80 20,6/83 28 WZ 18 068753 ●
350 3,5 2,5 70 100 20,6/83 28 WZ 18 068755 ●
400 4,0 2,8 70 100 20,6/83 24 WZ 18 068756 ●
3● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.1 Circular sawblades with wiper teeth
1
SB
TDISW
WZ
Application:
For cutting along grain - medium kerfs
Workpiece material:
Softwood and hardwood dry up to 15% wood moisture and long-fibred (poplar, balsa etc.) up to 110 mm cutting height.
Technical information:
With two external and two or four internal (over D-350 mm) wiper teeth.
Medium kerf - dry
WK 150-2-43
29
Dmm
SBmm
TDImm
BOmm
BOmax.mm
FLDmm
Z ZF SWDegree
ID
500 5,5 3,6 30 100 140 28 FZ 20 057993 ●
550 5,5 3,6 30 100 140 36 FZ 20 057994 ●
600 6,0 4,0 30 100 160 36 FZ 20 057995 ●
700 6,0 4,0 30 100 200 48 FZ 20 057997 ●
2 ● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.2 Circular sawblades with large recessed teeth
SB
TDISW
FZ
Square cut
Application:
For trimming in individual cuts, large cutting heights.
Machine:
Straight line edger, single-blade, multi-blade as well as single-spindle and double-spindle circular saw benches.
Workpiece material:
Softwood and hardwood wet, dry up and long-fibred (poplar, balsa etc.) up to 200 mm cutting height.
Technical information:
With four large recessed teeth.
Sawblades with 4 large recessed teeth
WK 100-2-07
30
3● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.3 Circular sawblades - thin kerf
1
SB
TDISW
FZ
Lamello cut
Application:
For cutting thin lamello cuts on horizonal spindles.
Machine:
Edger, single-blade, multi-blade as well as single-spindle and double-spindle circularsaw benches and moulders.
Workpiece material:
Softwood and hardwood, dry up to 10 % wood moisture and 60 mm cutting height.
Technical information:
With three interior wiper teeth. Efficient energy and wood utilisation from reduced cutting widths.
Sawblade with interior wiper teeth
WK 100-2-44, WK 100-4-44
Machine Dmm
SBmm
TDImm
BOmm
BOmax.mm
DKNmm
FLDmax.mm
Z ZF SWDegree
ID
200 2,0 1,4 30 24 FZ 20 067050 ●
200 2,4 1,6 30 60 100 22 FZ 25 067200 ●
220 2,0 1,4 30 24 FZ 20 067051 ●
220 2,4 1,6 30 80 120 24 FZ 25 067201 ●
250 2,0 1,4 30 24 FZ 20 067052 ●
250 2,4 1,6 30 90 120 24 FZ 25 067202 ●
RaimannTorwegge
250 2,4 1,6 70 21/83 120 24 FZ 25 067203 ●
Costa 250 2,4 1,6 80 13/89 120 24 FZ 25 067204 ●
300 2,8 1,8 30 100 140 30 FZ 25 067212 ●
Raimann 300 2,8 1,8 70 21/83 140 30 FZ 25 067213 ●
Costa 300 2,8 1,8 80 13/89 140 30 FZ 25 067214 ●
350 3,0 2,0 30 110 150 30 FZ 25 067216 ●
31
4 ● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.3 Circular sawblades - thin kerf
SB
TDISW
FZ
Lamello cut
Application:
For cutting thin lamello cuts on vertical spindles.
Machine:
Edger, single-blade, multi-blade as well as single-spindle and double-spindle circularsaw benches and moulders.
Workpiece material:
Softwood and hardwood dry up to 10 % wood moisture and 100 mm cutting height.
Technical information:
With two exterior (D < 250 mm) or two exterior and two interior wiper teeth. Efficientenergy and wood utilisation from reduced cutting widths and special tool bodycoating.
Circular sawblade with exterior and interior wiper teeth, coated
WK 100-2-43
Dmm
SBmm
TDImm
BOmm
BOmax.mm
NLAmm
FLDmax.mm
Z ZF SWDegree
ID
220 1,8 1,2 65 80 3/11/80 120 27 FZ 20 067039 ●
225 1,6 1,2 60 80 3/10/75 130 33 FZ 20 067040 ●
250 2,4 1,6 30 80 3/10/75 100 12 FZ 25 067041 ●
250 2,4 1,6 60 80 3/10/75 100 24 FZ 20 067217 ●
250 2,5 1,8 60 80 3/10/75 120 40 FZ 20 067032 ●
270 2,4 1,6 60 80 3/10/75 120 28 FZ 20 067033 ●
300 2,4 1,6 60 80 3/10/75 120 24 FZ 20 067218 ●
325 2,4 1,6 60 80 3/10/75 130 28 FZ 20 067042 ●
32
5● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.3 Circular sawblades - thin kerf
1
SB
TDISW
FZ
SB
TDISW
WZ
Lamello cut
Application:
For cutting thin lamello cuts on horizonal spindles.
Machine:
Edger, single-blade, multi-blade as well as single-spindle and double-spindle circularsaw benches and moulders.
Workpiece material:
Softwood and hardwood with wood moisture of 10 % to 18 %.
Technical information:
With curved, exterior and interior wiper teeth. Efficient energy and wood utilisationfrom reduced cutting widths. Curved wiper teeth for improved kerf clearance and improved chip ejection. Increased cutting performance and reduced resin build-upfrom special tool body coating.
Sawblade with curved, interior & exterior wiper teeth
WK 100-2-19, WK 150-5-19
Dmm
SBmm
TDImm
BOmm
DKNmm
Z ZF SWDegree
ID
250 2,4 1,6 70 21/83 20 WZ 20 067310 ●
300 2,6 1,6 30 20 FZ 20 067311 ●
300 2,6 1,6 70 21/83 20 FZ 20 067312 ●
350 2,8 1,6 70 21/83 28 WZ 20 067313 ●
33
Dmm
SBmm
TDImm
BOmm
DKNmm
FLDmm
Z ZF SWDegree
ID
250 2,0 1,4 80 19/9019/90
120 36 WZ 15 067053 ●
250 2,4 1,6 80 19/9019/90
120 32 WZ 15 067054 ●
6 ● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.3 Circular sawblades - thin kerf
SB
TDISW
WZ
Lamello cut
Application:
For cutting thin lamello cuts on horizonal spindles.
Machine:
Edger, single-blade, multi-blade as well as single-spindle and double-spindle circularsaw benches and moulders.
Workpiece material:
Softwood dry up to 10 % wood moisture and 40 mm cutting height.
Technical information:
With two exterior wiper teeth. Increased cutting performance and reduced resin build-up from special tool body coating.
Sawblade with exterior wiper teeth
WK 150-4
34
3● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.4 Circular Sawblades - thin kerf, noise reduced
1
SB
TDISW
WZ
SB
TDISW
WZ/FA
Lamello cut
Application:
For cutting gluable surfaces, medium kerf and lamello cuts on horizontal spindles.
Machine:
Single-blade, multi-blade as well as single-spindle and double-spindle circular sawbenches and moulders.
Workpiece material:
Softwood and hardwood, dry up to 10 % wood moisture.
Technical information:
AS LowNoise UT design - Noise reduction by up to 5 dB(A). Tool body with irregulartooth pitch. Continuous tool body without boss. Increased cutting performance andreduced resin build-up from special tool body coating.
Sawblade - AS LowNoise UT
WK 151-2-21, WK 150-4-21
Dmm
SBmm
TDImm
BOmm
DKNmm
NLAmm
FLDmm
Z ZF SWDegree
ID
250 2,4 1,6 80 19/9019/90
120 24 WZ 15 057487 ●
250 2,4 1,6 80 19/9019/90
120 40 WZ 15 057488 ●
300 2,8 1,8 80 19/90 2/13/1004/7/95
120 28 WZ/FA 15 057489 ●
35
2 ● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.5 Circular sawblades - extreme thin kerf
SB
TDISW
FZ
Sawblade with coated tool body
Application:
For cutting shoulder kerfs combined with medium kerf circular sawblades.
Machine:
Moulder with/without automatic feed of the workpieces. Used single- or double-sided, horizontally or vertically.
Workpiece material:
Softwood and hardwood, dry up to 10 % wood moisture, grade 0 to 1.
Technical information:
For sets assembled with thin kerf circular sawblades, medium kerf. Increased cutting performance and reduced resin build-up from special tool bodycoating.
Shoulder cut
WK 100-2-21
Clamping sleeves TB 270-0 and PH 130-0-01 see section 8 - Adaptors
Dmm
SBmm
TDImm
BOmm
BOmax.mm
NLAmm
DKNmm
FLDmm
Z ZF SWDegree
ID
180 5,0 4 60 3/10/75 100 32 FZ 20 057435 ●
200 5,0 4 60 3/10/75 120 36 FZ 20 057436 ●
225 5,0 4 30 110 3/10/75 120 25 FZ 20 057441 ●
225 5,0 4 60 3/10/75 120 40 FZ 20 057437 ●
250 5,0 4 30 120 3/10/75 140 25 FZ 20 057442 ●
250 5,0 4 60 3/10/75 140 36 FZ 20 057438 ●
250 8,0 6 80 4/7/952/13/100
13/89 100 24 FZ 15 057466 ●
300 8,0 6 80 4/7/952/13/100
13/89 100 24 FZ 15 057467 ●
325 5,0 4 60 3/10/75 120 24 FZ 20 057468 ●
SB
TDISW
WZ
Technical information:
For sets assembled with thin kerf circular sawblades, medium kerf. Special tooth geometry for low cutting forces at low feed speeds. Increased cutting performanceand reduced resin build-up from special tool body coating.
Shoulder cut - reduced number of teeth
WK 150-2-21
Dmm
SBmm
TDImm
BOmm
NLAmm
FLDmm
Z ZF SWDegree
ID
200 3,8 3 60 3/10/753/11/80
100 12+12 WZ 20 057469 ●
220 3,8 3 60 3/10/75 120 6+6+6+6 WZ 20 057461 ●
220 3,8 3 60 3/10/753/11/80
120 12+12 WZ 20 057470 ●
220 3,8 3 65 3/11/80 120 6+6+6+6 WZ 20 057462 ●
220 3,8 3 65 3/11/80 120 12+12 WZ 20 057471 ▫
225 3,8 3 60 3/10/753/11/80
120 12+12 WZ 20 057472 ●
250 3,8 3 60 3/10/753/11/80
120 12+12 WZ 20 057473 ●
36
3● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.5 Circular sawblades - extreme thin kerf
1
SB
TDISW
FZ
Application:
For cutting strips and lamellos on horizontal and vertical spindles.
Technical information:
Noise-reduced design from uneven number of teeth or irregular tooth pitch. Continuous tool body without boss. Increased cutting performance and reducedresin build-up from special tool body coating.
Middle cut
WK 100-2-21
Clamping sleeves TB 270-0 and PH 130-0-01 see section 8 - Adaptors
Dmm
SBmm
TDImm
BOmm
BOmax.mm
NLAmm
FLDmm
Z ZF SWDegree
ID
180 1,5 1,0 60 70 3/10/75 100 21 FZ 20 057443 ●
180 1,8 1,2 60 70 3/10/75 100 21 FZ 20 057444 ●
180 1,3 0,8 60 70 3/10/75 100 32 FZ 20 057418 ●
180 1,5 1,0 60 70 3/10/75 100 32 FZ 20 057419 ●
180 1,8 1,3 60 70 3/10/75 100 32 FZ 20 057412 ●
200 1,5 1,0 60 80 3/10/75 120 21 FZ 20 057445 ●
200 1,8 1,2 60 80 3/10/75 120 21 FZ 20 057446 ●
200 1,5 1,0 60 80 3/10/75 120 36 FZ 20 057421 ●
220 1,2 0,9 65 80 3/11/80 120 24 FZ 20 057474 ●
220 1,2 0,8 60 80 3/10/75 120 32 FZ 20 057463 ●
220 1,2 0,9 60 80 3/10/75 120 27 FZ 20 057475 ●
220 1,3 0,9 60 80 3/10/75 120 24 FZ 25 057476 ●
220 1,3 0,9 65 80 3/11/80 120 24 FZ 25 057477 ●
220 1,3 0,9 60 80 3/10/75 120 32 FZ 25 057478 ●
220 1,3 0,9 65 80 3/11/80 120 32 FZ 25 057479 ●
220 1,4 1,0 60 80 3/10/75 120 24 FZ 25 057480 ●
220 1,4 1,0 65 80 3/11/80 120 24 FZ 25 057481 ●
220 1,4 1,0 60 80 3/10/75 120 32 FZ 20 057464 ●
220 1,4 1,0 65 80 3/11/80 120 32 FZ 20 057465 ●
225 1,5 1,0 60 110 3/10/75 120 25 FZ 20 057447 ●
225 1,6 1,2 60 110 3/10/75 130 32 FZ 25 057482 ●
225 1,6 1,2 65 110 3/11/80 130 32 FZ 25 057483 ●
225 1,8 1,2 60 110 3/10/75 120 25 FZ 20 057448 ●
225 2,0 1,4 60 110 3/10/75 120 25 FZ 20 057449 ●
225 1,5 1,0 60 110 3/10/75 120 40 FZ 20 057422 ●
225 2,0 1,4 60 110 3/10/75 120 40 FZ 20 057416 ●
250 1,7 1,2 60 120 3/10/75 140 25 FZ 20 057450 ●
250 2,0 1,4 60 120 3/10/75 140 25 FZ 20 057451 ●
250 1,7 1,2 60 120 3/10/75 140 36 FZ 20 057433 ●
250 2,0 1,4 60 120 3/10/75 140 36 FZ 20 057434 ●
37
Dmm
SBmm
TDImm
BOmm
NLAmm
FLDmm
Z ZF SWDegree
ID
180 1,0 0,8 65 3/11/80 140 24 FZ 20 057484 ●
180 1,1 0,8 60 3/10/75 140 24 FZ 20 057485 ●
180 1,1 0,8 65 3/11/80 140 24 FZ 20 057486 ●
4 ● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.5 Circular sawblades - extreme thin kerf
SB
TDISW
FZ
Scoring sawblade with coated tool body
Application:
For scoring the tool leading edge of the workpiece.
Machine:
Moulder with/without automatic feed of the workpieces. Used single- or double-sided, horizontally or vertically.
Workpiece material:
Softwood and hardwood, dry up to 10 % wood moisture, grade 0 to 1.
Technical information:
Use only with extremely thin kerf circular sawblades. Increased cutting performanceand reduced resin build-up from special tool body coating.
Pre-scoring
WK 100-2
38
3● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.6 Circular sawblades for multi-purpose cuts
1
SB
TDISW
FZ
Shoulder and square cut
Application:
For cutting along grain - shoulder kerfs and square cuts.
Machine:
Straight line edger, single-blade, multi-blade as well as single-spindle and double-spindle circular saw benches and table saws.
Workpiece material:
Softwood and hardwood wet and dry up to 110 mm cutting height.
Technical information:
Large gullet and large, lateral tooth overhang for cuts in wet wood. Stable tool body design for square cuts.
Sawblade with strengthen tool body and large gullet
WK 100-2-01
Dmm
SBmm
TDImm
BOmm
BOmax.mm
DKNmm
FLDmm
Z ZF SWDegree
ID
210 3,4 2,2 30 90 100 16 FZ 20 057400 ●
250 4,0 2,6 30 90 100 18 FZ 20 057402 ●
300 4,0 2,6 30 100 120 20 FZ 20 057405 ●
300 4,0 2,6 70 21/83 120 20 FZ 20 057406 ●
305 4,0 2,6 30 120 120 24 FZ 20 057490 ●
350 4,4 3,0 30 100 120 20 FZ 20 057407 ●
350 4,4 3,0 70 21/83 120 20 FZ 20 057408 ●
355 4,4 3,0 30 120 120 24 FZ 20 057491 ●
400 4,4 3,0 30 100 140 24 FZ 20 057409 ●
450 5,0 3,2 30 100 140 28 FZ 20 057410 ●
500 5,0 3,2 30 100 140 32 FZ 20 057411 ●
SB
TDISW
FZ
Middle cut
Application:
For cutting along grain - medium kerfs.
Machine:
Straight line edger, single-blade, multi-blade as well as single-spindle and double-spindle circular saw benches and table saws.
Workpiece material:
Softwood and hardwood dry up to 15 % wood moisture and up to 110 mmcutting height.
Technical information:
Optimised design for medium kerfs. Large gullet.
Sawblade with large gullet
WK 100-2-10
Dmm
SBmm
TDImm
BOmm
BOmax.mm
DKNmm
FLDmm
Z ZF SWDegree
ID
210 3,2 2,2 30 90 100 20 FZ 20 057500 ●
250 3,2 2,2 30 90 100 18 FZ 20 057502 ●
300 3,2 2,2 30 100 120 20 FZ 20 057503 ●
300 3,2 2,2 70 21/83 120 20 FZ 20 057504 ●
350 3,5 2,2 30 100 120 24 FZ 20 057505 ●
350 3,5 2,2 70 21/83 120 24 FZ 20 057506 ●
400 3,5 2,2 30 100 140 28 FZ 20 057507 ●
450 3,8 2,5 30 100 140 34 FZ 20 057508 ●
500 4,0 2,8 30 100 140 36 FZ 20 057509 ●
39
404 ● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.6 Circular sawblades for multi-purpose cuts
SB
TDISW
FZ
Along grain and middle cut
Application:
For cutting along grain.
Machine:
Circular saw benches.
Workpiece material:
Softwood and hardwood dry up to 15 % wood moisture and 100 mm cutting heightand plastomers* up to 90 mm cutting height.
Technical information:
Tool body tooth shape with chip thickness limitation. Lower feed forces for high cutting heights. High cutting angle.
Sawblade with chip thickness limitation
WK 100-4-01
* = The tooth shape FZ/TR is recommended for cutting plastomers.
Dmm
SBmm
TDImm
BOmm
NLAmm
FLDmm
Z ZF SWDegree
ID
300 3,5 2,4 30 2/10/60 120 14 FZ 20 057000 ●
350 3,5 2,4 30 2/10/60 120 16 FZ 20 057001 ●
400 4,0 2,8 30 2/10/60 140 18 FZ 20 057002 ●
450 4,0 2,8 30 2/10/60 140 20 FZ 20 057003 ●
SB
TDISW
FZ
Middle cut
Application:
For cutting along grain - medium kerfs.
Machine:
Circular saw benches.
Workpiece material:
Softwood and hardwood dry up to 15 % wood moisture and 100 mm cutting heightand plastomers* up to 80 mm cutting height.
Technical information:
Tool body tooth shape with chip thickness limitation. Lower feed forces for medium cutting heights. High cutting angle.
Sawblade with large hook angle
WK 100-4-02
* = The tooth shape FZ/TR is recommended for cutting plastomers.
Dmm
SBmm
TDImm
BOmm
BOmax.mm
NLAmm
FLDmm
Z ZF SWDegree
ID
250 3,2 2,2 30 80 100 18 FZ 20 057050 ●
300 3,5 2,4 30 2/10/60 120 20 FZ 20 057051 ●
350 3,5 2,4 30 2/10/60 120 24 FZ 20 057052 ●
400 4,0 2,8 30 2/10/60 140 28 FZ 20 057053 ●
450 4,0 2,8 30 2/10/60 140 34 FZ 20 057054 ●
500 4,4 2,8 30 100 140 36 FZ 20 057055 ●
41
Dmm
SBmm
TDImm
BOmm
BOmax.mm
FLDmm
Z ZF SWDegree
ID
350 3,5 2,4 30 100 120 12 FZ 20 066261 ●
400 4,0 2,8 30 100 120 14 FZ 20 066262 ●
5● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.6 Circular sawblades for multi-purpose cuts
1
SB
TDISW
FZ
Along grain cut
Application:
For cutting along grain.
Machine:
Circular saw benches.
Workpiece material:
Softwood and hardwood wet and dry up to 100 mm cutting height.
Technical information:
Tool body design with round, closed tooth shape. Low feed forces for large cuttingheights.
Sawblade with round closed tool body
WK 100-3-01
41
2 ● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.7 Circular sawblades with cooling elements
SB
TDISW
FZ
Circular sawblade with internal cooling elements
Application:
For cutting along grain - shoulder kerfs and square cuts.
Machine:
Straight line edger, single-blade, multi-blade as well as single-spindle and double-spindle circular saw benches.
Workpiece material:
Softwood and hardwood wet and dry up to 90 mm cutting height.
Technical information:
Tool body design with four internal cooling elements. Large lateral tooth overhang forcuts in wet wood.
Shoulder and square cut
WK 100-4-16
Dmm
SBmm
TDImm
BOmm
BOmax.mm
DKNmm
FLDmax.mm
Z ZF SWDegree
ID
260 4,2 2,6 60 14,5/71 120 20 FZ 20 057220 ●
300 4,2 2,6 30 100 120 24 FZ 20 057221 ●
300 4,2 2,6 70 20,6/83 120 24 FZ 20 057222 ●
350 4,2 2,6 30 100 120 28 FZ 20 057224 ●
350 4,2 2,6 70 20,6/83 120 28 FZ 20 057225 ●
SB
TDISW
FZ
Application:
For cutting along grain - medium kerfs.
Workpiece material:
Softwood and hardwood dry up to 15 % wood moisture and 90 mm cutting height.
Technical information:
Tool body design with four internal cooling elements.
Middle cut
WK 100-4-39
Dmm
SBmm
TDImm
BOmm
BOmax.mm
DKNmm
FLDmax.mm
Z ZF SWDegree
ID
250 3,2 2,2 30 80 100 20 FZ 20 057300 ●
250 3,2 2,2 70 20,6/83 100 20 FZ 20 057302 ●
300 3,2 2,2 30 100 120 24 FZ 20 057303 ●
300 3,2 2,2 70 20,6/83 120 24 FZ 15 057304 ●
320 3,2 2,2 70 100 120 24 FZ 20 057305 ●
350 3,2 2,2 30 100 120 28 FZ 20 057306 ●
350 3,2 2,2 70 20,6/83 120 28 FZ 20 057307 ●
42
3● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.8 Sawblades for wood materials
1
SB
TDISW
FZ
Middle cut
Application:
For cutting panels along grain for flooring production.
Machine:
Multi-blade circular saws, models Paul, I.S.E., Becker etc.
Workpiece material:
Coated (HPL/CPL) particle and fibre materials (MDF/HDF).
Technical information:
Optimised tool body design for long life time. Circular sawblades BO = 115 mm for hydro-duo quick clamping element ID 030555 or BO = 100 mm for clamping flange TR 810-0.
Sawblade - HW tipped
WK 100-4-39
Dmm
SBmm
TDImm
BOmm
DKNmm
Z ZF SWDegree
ID
250 2,2 1,6 100 13/109 48 FZ 10 061433 ●
250 3,2 2,2 100 13/109 48 FZ 10 061434 ●
SB
TDISW
FZ
Middle cut
Application:
For cutting panels along grain for flooring production.
Machine:
Multi-blade circular saws, models Paul, I.S.E., Becker etc.
Workpiece material:
Coated (HPL/CPL) particle and fibre materials (MDF/HDF).
Technical information:
Optimised tool body design for long life time. Circular sawblades BO = 115 mm for hydro-duo quick clamping element ID 030555 or BO = 100 mm for clamping flange TR 810-0. 5.5 mm tipping height.
Sawblade - DP tipped
WK 100-4-39
Dmm
SBmm
TDImm
BOmm
DKNmm
Z ZF SWDegree
ID
250 2,2 1,6 60 36 FZ 3 190502 ▫
250 3,2 2,2 60 36 FZ 3 190503 ▫
250 2,2 1,6 90 8/7/106 36 FZ 3 190504 ▫
250 3,2 2,2 90 8/7/106 36 FZ 3 190505 ▫
210 2,2 1,6 100 13/109 36 FZ 3 090674 ▫
250 2,2 1,6 100 13/109 36 FZ 3 090668 ▫
250 3,2 2,2 100 13/109 36 FZ 3 090669 ▫
210 2,2 1,6 115 8/7/131 36 FZ 3 090697 ●
210 3,2 2,2 115 8/7/131 36 FZ 3 090698 ▫
250 2,2 1,6 115 8/7/131 36 FZ 3 090695 ●
250 3,2 2,2 115 8/7/131 36 FZ 3 090696 ●
43
4 ● available ex stock▫ available at short notice
1. Sawing 1.2 Cutting along grain
1.2.8 Sawblades for wood materials
SB
TDISW
FZ
Square cut
Application:
For cutting panels along grain for flooring production.
Machine:
Multi-blade circular saws, models Paul, I.S.E., Becker etc.
Technical information:
Cutting width can be extended in 5 mm steps to max. 32 mm with extensions. Circular sawblades BO = 115 mm for hydro-duo quick clamping element ID 030555. 5.5 mm tipping height.
Hogger for shoulder cut D-210/220 mm, SB-12 mm, DP tipped
SK 999-2
Cutting width extended in 5 mm steps up to 32 mm with extension parts.
exist. of Dmm
SBmm
BOmm
Z ZF SWDegree
ID
Hogging circular sawblade 210 3,2 115 36 FZ 3 090698 ▫
Hogging part 220 4,0 115 36 FZ 3 190518 ▫
Extension 220 5,0 115 18 FZ 3 190519 ▫
SB
TDISW
FZ
Hogger for shoulder cut D-250/260 mm, SB-12 mm, DP tipped
SK 999-2
Cutting width extended in 5 mm steps up to 32 mm with extension parts.
exist. of Dmm
SBmm
BOmm
Z ZF SWDegree
ID
Hogging circular sawblade 250 3,2 115 36 FZ 3 090696 ●
Hogging part 260 4,0 115 36 FZ 3 190520 ▫
Extension 260 5,0 115 18 FZ 3 190521 ▫
44