1. b. rip saw 2. d. used for cutting with the grain
TRANSCRIPT
1. b. Rip Saw
1. b. Rip Saw
• 2. d.
Used for cutting with the grain
3. a. Crosscut Saw
3. a. Crosscut Saw
• 4. e.
Used for cutting across the grain
5. d. Backsaw
5. d. Backsaw
• 6. c.
Used for very accurate, straight cuts… used in a miter box.
7. c. Coping Saw
7. c. Coping Saw
• 8. a.
Used for cutting curves.
9. e. Hack Saw
9. e. Hack Saw
• 10. b.
Used for cutting metal
11. a. Block Plane
11. a. Block Plane
• 12. c.
Used for straightening the end grain of a board
13. e. Jack Plane
13. e. Jack Plane
• 14. a.
Used for straightening the edges of long boards.
15. c. Smooth Plane
15. c. Smooth Plane
• 16. b.
Used to straighten the edges of short boards.
17. d. Cabinet Scraper
17. d. Cabinet Scraper
• 18. d.
Used for scraping defects from the surface of a board.
19. b. Sanding Block
19. b. Sanding Block
• 20. e.
Used for abrading defects from boards.
21. a. Adjustable Wrench
21. a. Adjustable Wrench
• 22. c.
Used to change and fit any size bolt or nut
23. c. Open End Wrench
23. c. Open End Wrench
24. d.
All of the above. Used for two fixed
sizes of bolts, sliding on to nuts from the side, turning nuts in a tight area.
25. e. Box End Wrench
25. e. Box End Wrench
• 26. b.
Used for sliding on to nuts from the top.
27. d. Combination Wrench
27. d. Combination Wrench
• 28. c
Used to turn nuts in a tight area
29. c. Slip Joint Pliers
29. c. Slip Joint Pliers
• 30. d.
All of the above.
Used for grasping various sized objects, turning nuts or bolts, pulling hard to grasp objects.
31. e. Long Nose Pliers
31. e. Long Nose Pliers
• 32. a.
Used for grasping small objects.
33. a. Locking Pliers
33. a. Locking Pliers
34. d.
All of the above. Locking on to various
sized objects, pulling nails, holding things in place.
35. b. Phillips Screwdriver
35. b. Phillips Screwdriver
36. b.
Used for turning x slotted screws
37. d. Standard Screwdriver
37. d. Standard Screwdriver
• 38. a.
Used for turnig straight slotted screws.
39. a. Hex Key Set
39. a. Hex Key Set
• 40. b.
Used for turning hex slotted screws.
41. b. Ballpeen Hammer
41. b. Ballpeen Hammer
• 42. a.
Used for mushrooming the heads of rivets.
43. d. Curved Claw Finish Hammer
43. d. Curved Claw Finish Hammer
• 44. b.
Used for driving nails.
45. e. Rubber Mallet
45. e. Rubber Mallet
• 46. c.
Used for assembling wooden parts.
47. c. Utility Knife
47. c. Utility Knife
• 48. d.
All of the above.
Cutting wood, cutting paper, cutting boxes.
49. d. Cabinet Scraper
49. d. Cabinet Scraper
• 50. a.
Used for removing scratches from the surface of a board.
51. a. Framing Square
51. b. Framing Square
• 52. e.
All of the above. Laying out studs,
figuring rafter lengths, measuring, checking for 90° angles.
53. d. Try Square
53. d. Try Square
• 54. d.
All of the above. Checking for
square, laying out lines, measuring.
55. e. Combination Square
55. e. Combination Square
• 56. d.
All of the above. Scribing parallel lines,
checking square, checking 45° angles.
57. e. Marking Gauge
57. e. Marking Gauge
• 58. c.
Used for scribing lines parallel with an edge.
59. d. Bench Rule
59. d. Bench Rule
• 60. e.
None of the above. Marking angles, checking squareness, scraping glue.
61. a. Dividers
61. a. Dividers
• 62. d.
All of the above. Transferring distances, scribing circles, dividing into equal parts.
63. c. Sliding T-Bevel
63. c. Sliding T-Bevel
• 64. b.
Used for copying angles.
65. e. Tape Measure
65. e. Tape Measure
• 66. c.
Used for determining length.
67. b. Web or Strap Clamp
67. b. Web or Strap Clamp
• 68. d.
All of the above.
Used for holding parts together while bar clamping, picture frames, clamping odd shaped projects.
69. d. Hand Screw Clamp
69. d. Hand Screw Clamp
• 70. d.
All of the above.
Securing material to tables, laminating stacks together, clamping glued boards.
71. a. C-Clamp
71. a. C-Clamp
• 72. a.
Used for general clamping.
73. d. Bar Clamp
73. e. Bar Clamp
• 74. a.
Used for clamping wide boards during gluing.
75. b. Bench Dog
75. b. Bench Dog
• 76. c.
Used for clamping large pieces to the table.
77. c. Flat File
77. c. Flat File
• 78. d.
All of the above. Smooting outside curves, smoothing edges of boards, smoothing flat lips on boards
79. a. Half Round File
79. a. Half Round File
• 80. d.
All of the above. Smooting inside curves, smoothing outside curves, smoothing flat surfaces
81. d. Rat Tail File
81. d. Rat Tail File
• 82. a.
Smoothing inside holes.
83. e. Triangle File
83. e. Triangle File
• 84. c.
Used for smoothing inside sharp angles.
85. b. Half Round Rasp
85. b. Half Round Rasp
• 86. a.
Used for coarse filing inside curves.
87. d. File Card
87. d. File Card
• 88. c.
Used for cleaning file grooves.
89. d. Bit Brace
89. d. Bit Brace
• 90. d.
All of the above. Used for holding auger bits, drilling holes, putting in screws.
91. b. Hand Drill
91. b. Hand Drill
• 92. b.
Used for drilling holes.
93. b. Nail Set
93. b. Nail Set
• 94. b.
Used for driving nails below the wood surface.
95. c. Center Punch
95. c. Center Punch
• 96. c.
Used for starting drill bits.
97. a. Scratch Awl
97. a. Scratch Awl
• 98. d.
All of the above.
Used for starting screws, scribing lines, lining up holes.
99. a. Wood Chisel
99. a. Wood Chisel
• 100. d.
All of the above. Used for removing wood from holes, scraping glue, cleaning out corners.