document resume ed 115 880 ce 005 718 title … · title fall department head report--peporting...

DOCUMENT RESUME

ED 115 880 CE 005 718

TITLE Fall Department Head Report--Peporting BoOklet 2.0 tothe Massachusetts Division of Occupational Education(Fiscal Year Ending June 30, 1975) for Drafting.

INSTITUTION Management and Information System for OccupationalEducation, Winchest,r, Mass.

SPANS AGENCY Massachusetts StatelDept. of Education, Boston. Div.of Occupational Education.

PUB DATE 30 Jun 75NOTE 176p.; For related documents, see ED 062 553; ED 068

646-647; ED 072 225; ED 072 228; ED 072 303-304; CE005 687-727; Instructions for completing the bookletare available in CE 005 701

EDRS PRICE MF-$0.76 HC-$9.51 Plus PostageDESCRIPTORS Annual Reports; Census Figures; Data Collection;

Demonstration Projects; *Drafting; *EducationalObjectives; Job Skills; *Management InformationSystems; Program Design; Program Evaluation; *Records(Forms) ; State Programs; Trade and IndustrialEducation; *Vocational Education

IDENTIFIERS Census Data System; *Management Information SystemOccupational Educa; MISOE; Terminal PerformanceObjectives; TERMOBS

ABSTRACTThe reporting booklet is required for the Census Data

System (CDS) of the Management Information System for OccupationalEducation (MISOF); it contains the reporting forms which collect datathat describe program structure and job-entry skill outcomes expectedof program completors in the individual occupational education areaof drafting. Utilization of instructional area is also determined.This booklet contains the terminal performance objectives (TERMOBS)for this program area. They are actually the forms by which theskills of program completors are reported by department heads. CDS,one of two major subsystems of the integrated management informationsystem, was developed to provide occupational education managers withcomprehensive data on which to base rational management decisions.Essentially, CDS contains descriptive information systematicallystructured in a manner which allows it to be used as a basis forsampling evaluative research studies. CDS collects and stores censusdata for all school system offering occupational education programs,including all data formerly collected by the Annual Federal Reportfor Occupational Information, except followup data. (Author /AJ)

***********************************************************************Documents acquired by ERIC include many informal unpublished

* materials not available from other sources. ERIC makes every effort ** to obtain the best copy available. NevertheleSs, items of marginal *

* reproducibility are often encountered and this affects the quality *

* of the microfiche and hardcopy reproductions ERIC makes available *

* via the ERIC Document Reproduction Service (EDRS). EDRS is not* responsible for the quality of the original document. Reproductions ** supplied by EDRS are the best that can be made from the original. ************************************************************************

Misoe Number2

Due Date

Name of School System System ID No.

Name of School School 10 No.

Name of Preparer of Report Title Telephone No.

Name of Department or instructional Area

THE COMMONWEALTH OF MASSACHUSETTS

DEPARTMENT OF EDUCATION

FALL DEPARTMENT HEAD REPORT-REPORTING BOOKLET 2.0

to the

DIVISION OF OCCUPATIONAL EDUCATION(Fiscal' Year Ending June 30, 1975)

for

DRAFTINGU S DEPARTMENT OF HEALTH.

EDUCATION i WELFARENATIONAL INSTITUTE OF

EDUCATION

THIS DOCUMENT HAS BEEN REPRO-DUCED EXACTLY AS RECEIVED FROMTHE PERSON ORORGANIZATION ORIGIN-ATING IT POINTS OF VIEW OR OPINIONS

STATED DO NOT NECESSARILY REPRE-SENT OFFICIAL NATIONALINSTITUTE OFEDUCATION POSITION OR POLICY

Before filing said statement, the superintendent shatman of the school committee, who shall countersign itamination, he finds it correct.(General Laws Relating to Education 1970: Chapter 72Sec. 3, Item 2)

I submit it to the chair-on oath, if, after ex-

, Sec. 2A, Item 4, and

1 hereby certify that all the statements contained in this report are true tothe best of my knowledge and belief, and that this Is a true statement, made

under the penalties of perjury.

THE COMMONWEALTH OF MASSACHUSETTS

DEPARTMENT OF EDUCATION

FALL DEPARTMENT 441 REPORT-REPORTING BOOKLET 2.0

to the

DIVISION OF OCCUPATIONAL EDUCATION(Fiscal Year Ending June 30, 1975)

for

DRAFTINGU S OEPARTMENT OF HEALTH,

EOUCATION I. WELFARENATIONAL INSTITUTE OF

EDUCATION

THIS DOCUMENT HAS aceN aePWO-DUCED EXACTLY AS RECEIVED FROMTHE PERSON ORORGANIZATION ORIGIN-*TING. IT POINTS

OF VIEW OR OPINIONSSTATED DO NOT NECESSARILY REPRE-SENT OFFICIAL NATIONAL

INSTITUTE OFEDUCATION POSITION OR POLICY

Before filing said statement, the superintendent shall submit it to the chalr-man of the school committee, who shall countersign it on oath, if, after ex-amination, he finds it correct.(General Laws Relating to Education 1970: Chapter 72, Sec. 2A, Item 4, and

Sec. 3, Item 2)

I hereby certify that all the statements contained In this report are true tothe best of my knowledge and belief, and that this Is a true statement, madeunder the penalties of perjury.

(Date)

(Date)

Superintendent of Schools

Chairman of School Committee

TABLE OF CONTENTS

Page

Table 2.1 Enrollment in Final Grade by Student Group andTerminal Objectives (TERMOBs)

Table 2.11 Enrollment in Lower Grades by Student Group 6

Table 2.2 Utilization of Student Class Time: Final Grade 10

Table 2.21 Utilization of Student Class Time: Lower Grades 12

Table 2.3 Utilization of Departmental Instructional Area 14By Rooms

REPORTING TERMINAL PERFORMANCE OBJECTIVES (TERMOBs)

Table T-I Instructional Division and Unit Outline 1-2

Table T-IA Additional Instructional Divisions and Units 1-6

Table T-2 TERMOB Division and Unit Outline T-8

Table 7-2A Additional TERMOB Divisions and Units 7-9

TERMOBs

Table T-3 List of Basic Supplies T-I26

Table T-4 Additional TERMOB Performance Statements T-I 8

Index of TERMOB Statements 1-130

Mi7oe5

Table 2.1 Enrollment in Final Grade by Student Group & Terminal Objectives (TERMOB)

3

. Grade

2.

Student Group Nameand Number

.

101 102

7. USOE Codp(s)

4. Level Code

. Type Code

6. Session Code

.

.-----_____,

<I I 2 3 4 <1Program Length (Years)

. Cooperative Yes No . Yes No

.,. Workstudy Yes No Yes No

10. Exploratory Yes Yes No

II.

B.

Instructors andTeacher's Aides

A. Full Time

II

Percentage cif Time

12. ErrcThment Male Female Male Female

TERMOB Applicability

. Session Code

7. Program Length (Years) A I 2 3 4 <II 2 3 4

. Cooperative Yes No Yes No

. Workstud' Yes Nei Yes N-

10. Exploratory Yes No Yes No

II. Instructors andTeacher's Aides

A. ' li Time

...

. Percent@ e )f Time

12. Enrollment Male Female Male Female

TERMOB Appli ability

TERMOB Nuriter

aao

ID

So

II.

0

0

111111011111

11 111 1111111111111111111

111111111111111

111111111111M

11111111111M

11111111111111

111111111111111

ME

MO

1111011111M11

1111111111111M

111111111111111

SIM

NO

liM

t-111N

M -

-IIII'

-a

IIMM

EM

1111111111111

II 1111111111111111

111111111111111MIIIM

I

1111111111111111111111111

011111111111111111111111

1111111111111111111111111

1111111111MIN

NU

M111111111111111111111111

11111111111111111011M1

1111111111111111111111M

11011111101111111111111

1111111111111111111111111

-MTZJIT&17-4

Table 2.1 Enrollment In Final Grade by Student Group & Terminal Objective (TERMOB)

7 8

. Gra e

Student Group Nameand Number

. USOE Code)

. Level Code

T e Code

Sesion Code

Co J erative

A. Full Tire

B.' Percenta e of Time

Female

TERMOB Applicability

I!. TERMOB Number

5. Type Cede

Session Code

. Pr- r m Lent Ceearsi,

. Coo eratIve

W-r,tudv

0. E ratory

Instructors andTe:Taher'.i., Aides

A. Fall Time

Percen a e of Time

Enrollment

<|

TERMS Applicability

. TERMC3 Number

.11111211111111111111 Inn MIN1111111111 NMI MINI

11111111 M11 11E11MIN NMINMI In.11111111

1111

11111111111111111111

immin iiimoniImmu=monmin=

111111110

1111111111.1111111111111111111

J. 0

4

1:

'NO

1

;I:

5;-

1111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111

M O

M

I 11

1111111111111.11M

IN N

OM

MIN

IMN

MI

MIN

N111111

11111111111.1111N

MI

NM

I1111111111111.111

111111111111.11111N

MN

MM

UM

ME

MN

1111.11111111111M

INI 1.11111

WM

ME

M IIIIIIIIIIIIIIII

ME

M M

N 111.1.1.1.1111

MIM

I ISM

11111111111.1111111111111111111111111111.111

MIN

IM

INIM

UM

. 11111.111111.111M

IMI 11111111111111111111.11111M

INIM

NM

INIM

INN

IMIN

I111111111111111111111 111111111111111111E

MI M

IN M

INN

UM

MN

MN

OM

111111111111111111111111111M

IMI 11111111111111111111111111M

N N

M111111111111111 M

OM

MIN

IMM

INN

MIN

1111111111111.11111111111111111111111111MIM

I1111.11111111111 11111111111111111111111111110N

M IM

MO

111111111111111111111111111.NN

E M

EM

!M

I= M

IMI=

111111111111111111111111.111.01111.1111.11110iiminsm

n

11

0*I

00

41

.4

ME

MIN

IMIM

MI

Nil

1111111111111111111

MiiinniiiiiiiiiM

1111111110111111111111101

11011101111111111111M

ININ

1111111111111111M=

1111111101111111111111M

1111111111111M0011111

IIIIIIMM

INE

M11111111M

EM

IffillIM1111111111111111111111M

111111111111111111111M

L.

Table 2.11

rot I

me

ntin Lower Grades by S t udent Group

3 ,--

56

?c.,

:03

204

Z05

,

_

IC 1

23

41

34

4: i_

t,

,<

Yes

go

Yes

Na

Ye

Yes

No

Yes

No

Yes

No

'Nes

No

)(es

No

Yes

No

Yes

No

YeS

tL'

.44S

No

`:'es

No

Yes

No

,

- 111111111

111111111111111

11111111111M.

tt

111111101.11111111111111111111101

MN

t

,

111111111111111111111111111111

IIIMa 1 a

Fema 1 e

a 1 e

Fem a 1 e

Mel e

F,4male

Male

Fema 1 e

Male

Table 2.11

Enr

otire

rri-in Lower Grades by Student pup

I.

Grade

.,

4.Sfudent Group Name

and Number

.

m2k7

..,

--)04

USOE Code(s)

4.

LEV5L Code

5.LEtpe.Code

,......._.

6.

Session

Cod

e.

27.

PrOarop Len th (Years)

<I

I3

4<I

I2

3.. 4

.< i

$2

<E

Coo

p ar

e bi

tYes

Wo

Yes

NO No

-

Yes

No

"X'es

go ,

Yes

N

Yee

No

9.

-

Workstudy

Yes

No

' Ye' 's

40.

1t

.

EXpissreit014

inst

ruct

ors

and

Teacher's Aides

A.

Fuji Time

111111111111111111111

E.

Percentage of Time,

Yee

11111111111111

Nc

Yes

Yes

'

No

`Fes

NG

f l

12.

Enrollment

male

Female

'ale

Female

Male

F rna l e

. zle

1111Ent

Table 2.11 (Cont'd) Enrollment in LowerGrades by Student Group

208

It

209

12

210

Yes

No

Yes

No

Table 2.11 (Cont'd) Enrollment in

Lower Grades by Student Group

q10

it

1.]

Grade

2.

Student Group Name

and Number

206

207

208

209

3.

USOE Code(s)

4. .

Level Code

T ie Code

6.

Session Code

7.

8.

Program Length (Years)

<1

12

34

<1

12

3<1

12

34

<1

I2

3

Coo erative

Yes

No

Yes

No

Yes

No

Yes

No

9.

Workstud

Yes

No

Yes

No

Yes

No

Yes

No

10.

Ex iorator

Yes

No

Yes

No

Yes

No

Yes

No

If.

instructors and

Teacher's Aides

A.

Full Time

B.

Percentage of Time

Male

ema

eMale

Female

.-7-emale

Male

-ere

42.

Enrollment

Table 2.11

Enrollment in Lower Grades by Student Group -(Contlet)

4 6

1 7

I..

C

211

7,

2[3

214

C 3 0

25

.,

ears)

12

34

<I

t2

34

<I

I2

34

<I

I2

34

<I

I2

3

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

'

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Time

t

1

f Time

111111111

Male

Female

Mate

Female

Aale

Female

Male

Femal-

Mal-

F u,

-

I

13Table

.11

Enrollment In Lower Grades by Student Group (Cont'd

16S

7

I,

Grade

2.

Student Group Name

and Number

211

211'

213

14

3.

USQE Code(s)

A

4,

Levet Code

.Type Code

5.

Session Code

.Program, Length (Years)

'<I

<1

<1

34

<I

,

8.

Cooperative

Yes

No

Yes

No

Yes

No

Yes

9.

Workstudy

Yes

No

Yes

No

Yes

No

Yes

O.

EWoratory

Yes

I

No

,

Yes

No

,

Yes

No

Yes

11.

I

Instructors and

Teacher's Aides

A.

Full Time

B.

Percentage of Time

Enrollment

Male-

'4

Female

Male

Female

, Male

Female

- Mat

e

12

4_

1111111:101711113011111111111101=1111111111E

1011111MM

EI

aiewZ

1111==

=111111111111111111111111111111111111111111111

111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111

1214

19

.,

Grade

2.

Student Group Name.

and Number

216

217

218

219

3.

USOE Code(s)

4.

Level Code

.be Code

6.

Session Code

.1,Proram Lenth (Years)

4:1

12

34

All

I2

3- 4

<1

12

34

S.,' ;Cooperative

Yes

No

Yes

No

Yes

No

Yes

No

9.

Workstudy

Yes

No

Yes

No

Yes

No

Yes

No

10.4

Exploratory

Yes

No

Yes

No

Yes

No

Yes

No

li.

Instructors and

Teacher's Aides

A.

Full Time

B.

Percentage of Time

12.,

Enrollment

Male

ema e

Mate

Female

Male

'Ferro e

.

Table 2.2

UtHizat1or of Student Class Time:

.3

46

Final Grade

79

tat

102

103

104

105

106

107

108

109

110,

Table 2.2

Utilization. of Student Class Tice:

Final Grade

67

Student Group r.um er

101

10Z

10:

104

105

16

107

,.

Grade

3.

USE Code(s)

In Occupational

Shop /Lab AreaCs1

.

5.

in Occupational

Related AreaCs)

111111

111111

111111

111111

Total Occupational

Time f Lines 4 + 5)

In Nonaccu ational Areas

8.

Total All Areas

(Lives 6 -1- 7)

9.

Length of Grade Session

(weeks)

10.

,-

Schedule Variation

U.

Additional Notes

Necessary tc Explain

Lines 4 Through 10

Table 2.2

Utilization of Student Class Time (Cont'd): Final

Grade

IA

Table 2.2

Utilization of Student Clas0 Time (Cont'd): Final

Grade

1.

Student Group Number

III

112

113

,114

115

117

2.

Grad-

3.

USOE COde(s)

111

III

4.Etapilab

5.

In Occupational

Area(s)

In Occupational

Related Area(s)

6.

Total Occupational

Time (Lines 4+ 5)

7.

In Nonoccu ational Areas

8.

Total All Areas

(Lines 6 4 7)

III

9.


(weeks)

0.

Schedule Variation,

1.'Lines

!Additional Notes

,Necessary to Explain

4 through 10

Table 2.21

Utiliz.:11-1,Dn of Student Class Time:

Lower Grade

I.

tudent Grou Number

?ni

1120

:71-)3

,

207

203

2.

Grady

I

3.

WOE Cede (s)

4.

in Occupational

Stop/Lab Area(s)

5'.

in Occupational

RelateArea(s)

6.

Total Occupational

Tine (Lines 4 + 5)

7.

in Nonoccupational Areas

8.

Total All Areas

(Lines 6 + 7)

9.


(Weeks)

O.

Schedule Variation

Additional Notes

Necessary to Explain

Lines 4 through 10

Table 2.21

Utilization of Student Clasc) Time:

Corer Gr3de

Tabte 2.21 (Cont'd) Utilization of Student Class Time:

Lower Grade

t3

14

15

16

'

17

le19

216

217

20

21

22

218

219

220

z

Table 2.21 (Contld) Utilizationof Student Class Time:

Lower Grade

15

17

9....

:I.

2.

Student Grou. Number

211

,

212

213

214

215

216

217

Grade

3.

USOE Cadets)

4.

.*

,

5.

in Occupational

Shop/Lab Area(s)

In Occupational

Related Area(s)

.

6.

Total Occupational

Time (Lines 4 + 5)

7.

In Nonoccupational Areas

8.

Total. All Areas

(Lines 6 + 7)

9.


(Weeks)

10.

Schedule Variation

11.

Additional Notes

Necessary to Explain

Lines 4-through 10

Mlsoe Number

29

Table Utilization of Dopa tmental instructional Area by Rooms

NCheck Applicable Program Schedule

I. a. [ 3 Weeklyb. [ 3 Alternating

[ 3 Variable

2. a. E 3 Semester Schedule Change

b. [ 3 No Semester Schedule Change

WEEKLY OR SCHEDULE A

4

Room

No. o

Name

Day

of the

Week

Morning

7:00 a.m.-!2:00N

Afternoon

12:00N-6:00 p.m.

Evening

6:00 p.m.-11:00 p.m.

No. ofHrs.Used

No. ofStud. Hrs.

No. ofHrs. Used

No. ofStud. Hrs.

No. ofHrs. Used

No. ofStud. Hrs.

IA Mon.Tiles.

,

Wed.Thurs.Fri.

LS C Sat.

TOTAL`

2A Mon.Tae_,.

WedThurs.Fri.

LS C Sat.

TOTAL

3A Mon.Tues.Wed.Thurs.,

Fri.

S C Sat.

TO`V'ALS

4A

LS C

Mon.Tues.Wed.Thurs.Fri.Sat.

TOTALS

5A Mon.Tues.

Room

No. r

Namb,

IA

Day

of the

Week

Morling

7:00 am.-12:00N

Mon.

Tues.Wed.Thurs.

No. oT No. ofHrs.Used Stud: Hrs.

Afternoon

12:00N-6:00 p.m.No. of

Stud. Hrs.No. of

Hrs. Used

Evening

6:00 p.m 11:00 p.m.No. of No. of

Hrs. Used Stud. Hrs.

LS C

TOTAL

Fri.MINMEMI=IM=M101.1

LS C

TOTAL

5Wed.Thurs.

LS C

4A

Fri.Sat.

Mon.Tues.

ldrim=1111111111111MSat.

OTALS

5A Mon.Tues.

Wed.Thurs.

LS C Sat.

TOTAL

30

14

Misoe Number

Table 2.3 (Cont'd) Utilization of Departmental Instructional Area by Rooms

Check Applicable Program Schedule

1. a. E 3 Weeklyb. [ 3 Alternatingc. J Variable

2. a. [ 3 Semester Schedule Changeb. -[ ] No Semester, Schedule Change

WEEKLY OR SCHEDULE B

7 8 9 10

Room

No. or

Name

Day

of the

Week

Morning

7:00 a.m.-12:00N

Afternoon

12:00N-6:00 p.m.

Evening

6:00 p.m.-11:00 p.m.No. ofHrs.Used

No. ofStud. Hr .

No. ofHrs. Used

1 No. ofStud. Hrs.

No. ofHrs. Used

No. ofStud. Hrs.

1 a Mon.

...

Tues.Wed.

Thurs.Fri.

LS C I Sat.

TOTALS

2 B Mon.Tues.Wed.Thurs.Fri.

LS C Sat.

TOTALS

3 B Mon.fiies.

Wed.Thurs.Fri.

L C Sat.

TOTALS

4 B Mon.

Tues.!fed.

Thurs.01...0.4.1.P.

r

LS- C at.

TOTALS

5 a Mon.

'WEENLT VII Mr114VULX. D

6 7 a 9 10

Room I

No. or

Name

Day

of the"No.

Week

Mon.

Morning

7:00 a.m.-12:00N

Afternoon

12:00N-6:00 p.m

Evening

6:00' p.m.-I1:00No. of

f

firs. Used

p.m.No. ofStud. Hrs.

ofHrs.Used

No. ofStud. Hrs.

No. ofHrs. Used

No. ofStud. Hrs.

i B

,Tues.Wed.Thurs.Fri.

LS C Sat.

TOTALS

2 8 Mon. _.__________--Tues.Wed.Thurs.Fri.

LS D Sat.

TOTALS

3B Mon.Tues.Wed.Thurs.Fri.

LS` C Sat.-.......,

TOTALS

4 B Mon.

ed.Thurs.Fri.

LS C Sat.

TOTALS'

5 B Mon..

'rues.Wed.Thurs.Fri.

LS D Sat.

TOTALS

3215

Mlsoe Number 33

Table 2.3 (Cont'd) Utilization of Departmental Instructional Area by Room


1. a. [ 3 Weeklyb. ] Alternatingc. E 3 Variable

2. a. [ 3 Semester Schedule Change

b. E J No Semester Schedule Change

11 15


12 13 14

Room

No. or

Name

Day

of the

Week

Morning

7:00 a.m.-12:00N

Afternoon

12:00N-6:00 .m.

Evening

6:00 p.m.711:00 .m..

No. ofHrs.Used

No. ofStud. Hrs.

No. ofHrs. Used

No. ofStud. Hrs.

No. ofHrs. Used

No. ofStud. Hrs.

bA

Mon.Tues.Wed.

11111.111111111.11111.11.1111111=

111.11.11.11.1111MI

Thurs

Fri. IIIIIIIIIILS C EMIIIMIIIIIIMMIOTALS

EIUIIIIIIIIIEMENIIIIPIIIIIIIIIIIIIIIW

IIIMIlliallinnalMEallIMINIMINIIIIMMIMM.1.111111.1.111.111111"111.11.1MINIM 111.111.111.1111111.111111=11111.1111111111MNIMIIIMINIMIMIIIIIIIII

ammilifilliellill1111111111111.1111MI1111111.111NMINIMMIIIMIMMEMOMMOIMINglimill111.111=11.11111111111011.1111111MMINIMMIMMIIIIIMMIllil11111.111.1111111.1111111mmimminummummm

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

IIIIIIMIN111111.111.111.111.11.111

11111.111111111111111111

IMMINIIIIIIIIIIIIIIMUMMIIII

11111111

ThursFri.

LS C

TOTAL

Sat.

IIIIIIIMMINIMMIMMIMIMINIMILINIM1111101.111111111111111111Tue.8A

IMINIUMMOINIMUMINIMMIIIIINIUMMIIIIIIIIIIMIIIIIIIIMIMTOTALS111.1111.1111111111

Wed.

IIIGUILIIIIINOIIIIIIIIIIIIMIIIIUIIINIIMMIIIIIIIIMIIIIIIIIIIIIIIIIIMIIINIIIIIIIIII

1211111101111111111111111111.111.11.11111Taos.Wed.Thurs.UAIKIMIIIMMINIIIIMMIIMINIMIUMIIIIIIIIFri.

La C 'Sal.

TOMS

ral111.111111111111111111111111.111111111.11111.111

Room

No. or

Name

Day

of the

Week

Morning

7:00 a.m.-12:00N

Afternoon

14:00N-6:00 ..m.

Evening

6:00 i.m.-11:00 *.m.

No. of No. ofHrs.Used Stud. Hrs.

11111111111111111111111111MMIIIEMEM

No. of No. ofHrs. Used Stud. Hrs.

No. ofHrs. Used

No. ofStud. Hrs.

Mon.

6A

REIMMIMEMIIIIIMMIIIIIIIIIIIIIII

TOTALS

Tues.Wed.Thurs IIIIIIIIIIIIFri.

111111111111

7A

-IN,_Tues.

11111.11111111111 111111111111.111111

11.1111111=1111111.1111111=1111Wed. 111.11.11.11ThursFri.

LS G 5t.

TOTAL!

AIMMIIIIIIIIIMIEMIWed.

IIIIMINIIIIMMI

111111.1111111111M11111111111MIIIIMIIIIIIMIIIIIIMII

MINIM111111111.111.111111111.1111

111.1111111111

11111111M

1.111111111111111111.11111111

1111.111111111111111111111.1

MIN

IIIIIINIIIIII

MM.Thum

LS 6 St.

TuTALS

9;

IMIIIIIIMMINIIIIIIM11.110.111111111.011111.

TOTALS

IMIIIIIIIINIIMUIIIIIIIIIIIIIIIIIITues.Wed.

1111111111111111111111111111111111111111111

11111111111111

NIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Fri.

MI=IIIIIIIII1

III=1311111111.111111111111 1111111111111111MMIll

immoinimmilimmimgm=1.111.11.111111111111MEMEMIII=1111111.1111111MMIIIIIIIMMIMMIIIIIMII=111111111111.011.11=

Thurs.Fri.

LS Sat.

73TALS

diMlsoe Number

Table 2.3 (Contle) Utilization of Departmental Instructional Area by Room


1. a. [ 3 Weeklyb. E 3 Alternatinclc. [ j Variable

2. a. L 3 Semester Schedule Changeb. [ J No Semester Schedule Change

WEEKLY OR SCHEDULE B

16 17 18 19 20

Room

No. or

Name

Day

of the

Week

Morning

7:00 a.m.-12:00N

Afternoon

12:00N-6:00 i. .

Evening

6:00 ..m. 11:00 ..m.N. ofrs.Used

No. ofStud. Hrs.

No. ofHre. Used

No. ofStud. Hrs.

No. of No. ofHrs. Used Stud. Hrs.

6B Mon. IIIIII I

ME= 1111111111111111111111111.1111ed. MUM IIIIIIIIIIMMI111.11111.11111111111

IIIIIIIIIMIIIINThurs.111111111Muumnimmummil

1111111111111.111111111.11.11.1111111111111111111111111.111.

11.111

F.L C Sat.

TOTALS

76 Mon. IIIIIIIIIIIMOM=e

tiCIEMIM=Fri.

NIMIIMMIMMIIIIIIIIMilliiIIII 0111.111111.1_ 11111111111 ft

LS C Sat.

TOTALS.........

86 Mon. 111111111111111111111111111111111111

....-=111111.11111111

Tues. 111111.111111111111.1111/1111111.11.11

Wed. inMilill1111111=111.1111.11111MIMIIThurs.

WIRMIIIIIIIIIIIIIIIIIMIIIIIIIIIIMINI=M11111.1.1Sat. 1.111111.1.1111MINIMIIII

1111.11MC

TOTALS

96 Mon.

TUu. 11111111i IIIIMIIIIIIIIIIIIIIIIIIIIIIIIIIILIIIIIIIMILIIIIIIIIIIIIIIIIIIII

1111111111111111111.1111111111111111111111111=11111111111111111

1111111111111

Wod. 111111.1.Thurs.1.1111111111111.111.11111111.11111/111111111.11111111MMIIMIMMI

InanlIIIIIIIIIIIIMIIMMUI1111101111111111111111INIENSat. 1111111111111M1111111111111111111111

111LS C

TOTAL

Mo106 n.

IIIMMIIIIIIIIIIIIMMIIMINIMIMOM

16, 17 18 19 20

ROOM

No. or

Nan-

Day

of the

Week

Morning

7:00 a.m.-12:00N

Afternpon

12:00N-6:00 ,.m.

Evening

6:00 ..m.-11:00 p.m.V:). of

rs.UsedNo:- of-

Stud. Hrs.No. of No. of

Hrs. Used Stud. Hrs.No. of

Hrs. UsedNo. of

Stud. Hrs.

6B Ion.

..

TuJs.oged.

Thurs.

LSC Sat.

TOTALS

78,... MINNIMOIMII

Wed. 1111111111111111111111Thurs. 11111111111Fri.

111.11111.1111111111.1111111111.1.1111111.111111.111EagginaplaTOTALS

88 MOI.Tues.Wed.Thurs,

Fri. IIIIIIIIIIIIIIIIIIII 111111111111111111LS C MEEEMIIIIIIIIIIIIIIIIMIMIIIMHIIIIIIIIOIUIIIIIMIIIIIIIMIIIMIIIIIIIIII

TOTALS

IIII98T ue s .

1111201111h urs. 11.1111.111111111111111011111111111111111.11111111.11111111/11.1

11101111111111111.111111111111111111NIIIIIIIIIIINUIIIIINNIIIII

Fri. 11.11111111==111111.11111.1111111111111

IIIIIIHIMIIIIIIIIIIIIIIIIIIIIIHIIIIIIII111111

111111111111

MINIMMEIMMININM111.1111

111111111011111111

11111110111

1111111111111111111111111111111

.LC Sat.

MAU?

108 Mon.WMirmaIlliMummimiminsiMMININIMimm

iIIIIIiiiniliiiIiiIIIIIIIIIIIIII.

IS Sat.

TOT.81_

17

MIsoe Number 37

Table .3 iContld) Utilization of Departmental Instructional Area by Room


a. C J Weeklyb. E 3 Alternatingc. [ 3 Variable

2. a. 3 Semester Schedule Changeb. C j No Semester Schedule Change

WEEKLY OR-SeHEDULE A

21 ,._ 23 24 25

Room

No. or

Name

Dag Morning

of the 7:00 a.m.-12:00N

Afternoon

12:00N-6:00 ..m.

Evening

6:00 N. .-I1:00 $. .

N9. ofWeek Hrs.Used

No. ofStud. Hrs.

No. ofHrs. Used

No. ofStud. Hrs.

No. ofHrs. Used

No. oStud. Hrs.

'IAMon.Tuos.

We .

11111.111111111111111111111111111

hu -Fri.

11111111111111111111111111111111111IIII111111111111111111

L mat. 111111111111111111111111

IIMIIIIII11.111111111Mil

Tows

EIMIIIIIIMIIIIIIIIEIIIIIIIMIIIMIIIIIIIIII

I2A

Mun.

Tue5.

11091111111111.111.ThU 11111111111111111111111

111111111M11111111111

rl. 11111111111L0 Jag -t'

IMIMIIMIMIIIIIMIIIIIIIIIIIIII11111111111 1111111111111

TDTAL

13A

L

13.11111111111111111111111.11111111.111.111111111111111.11IIMMIIIIIMIMIIIIMINIIIIIIIMIIIII11111111111.11111111111111111.111_W IIIMMINIMIIIIIIIIIIIMIIIIIIIIIIIIIIMUM1111.111

IIIOIIIIIIIIIIIIIIIIIIIIMNIIIIIIIIIIIIIIMIIIIIIIIIIIIIIIIIIIIIIIIIIIIIMIIIII

11111111.1111=MN1111.1111111111111

IIIIMllillIllMIIIIIIIIIIIIIMIIIIIIIIIII.11.1111111111111111111111.1111111111.11.1111NM

rhur.F 0.

t.

FJTALS

14A

Mo4i. 11111111111111111.101111111111111111111.1111.11111111.11111111111.1111.11.111111111111101111111111111.1111MIMI1.11111.11111111111111111111.1111111111111111.111.1I1111111111110111MMIIMMINIMIIIIIM=IIIIIIIIIIMIIIIIIIIIIIIIMIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIM

MIIIIIIIIIIIIIIIIIIIIIIIIIIIIIMIIIIIIIIIIIIIIIIIII

MIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Tues.Wed.T ursPri.

L

TOTAL

EIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIINSA" INEMINIIINIMMOMMIMMIMMIMMW

21 ..,.. 23 24 25

Room

No. on

Name

Day Morning

Of the 7:00 a.m.-12:00N

Afternoon

12:00N-h:00 8. .

Evening

6:00 .m.-11:00 ..m.NJ. of

Week Hrs.UsedNo. of

Stud. Hrs.No. of

Hrs. UsedNo. of

Stud. Hrs.No. of

Hrs. UsedNo. ofStud. Hrs.

11A

Mori

fue.Wed.Thurs.

LS C

TOTALS

1:A Tues.Wed.Thur3.%-ri.

, C.Y.

10TAL::------.....-

I3A

Mcn.Tue.Wed.Thurs.Frn.

'IoTALs

J . IIIIIIIIIII

I4A

Moll.

ut*).

Wed.Thur_i. 1111111111

11111.1MIMIIIIMMINII11111111111

111111.11.1111111.....

Frt.U.7 Si .

TOTAL

IrA

1

gun._

&A. 141111111111111.1111.11.1111.11111111.M.M......0Thur,:,.

I- . IlliiMlliaIMIMNBIIIMMMMIMN.11111111111111.111111.1111 IN=1_ . (

Is

39 hiiso, r° weber

Table 2.3 (Conf.0) Utilization of. OeporTmenTal Instructional Area by Room


i. a. 3 Weeklyb. 3 Alternatingc. C 3 Variable'

2. a. [ 3 Semester Schedule Changeb. E 3.N6 Semester Schedule Change

26 27

WEEKL-Y-1)R-SCHECULE-8

28 29

Room Day

No. o of the

Name Week

11B Mon.

Morning

30

Afternoon Evening

7:00 a.m.-12:00N 12:00N-6:00 p.m. 6:00 ..m. 11:00 p.m.No. o No. of No. of No. of No. o No. ofHrs.Used Stud. Hrs. Hrs. Used Stud. Hrs. Hrs. Used. Stud. Hrs.

rues,Wed.

MOM

138

Wed.

Room

No. o

Name

1 I B

27

Day

of the

Week

Mon.Tues.

28 29

7:00 a.m.-12:00NNo. of

Stud. Hrs.No o

Hrs.Used

Wed.

111131111

11E1111111111111012111111111111111111111111111111111111111111

TOTALS

128

1111111111111111111111111111111111111111111111111111 11111111111111111111

1=11=111.1=11111=1Mon.

MINIM

1111.11111111111

Wed.111111=71Fr

LS C Sat.

TOTALS

138

IliEMININIMINIMPOINNIIIMINIIMIIIMINNIII1111111 11.1111111111

IIMIIIIMIllLamminammommums wimmiummairimTOTALS IIIIIIIIIIIIIIIMIIIIIIIIIIIIIIIMMI1111111111111111111111111I11111111111

raril.11M=11111M=111L=IIIIIIIIIIMIIIMI 1.111.1111111111111111MIIIIIIIIIIIIII.NOM IIIIIIIIIIIIIIIiiiIIIIIIIIMIIIIIIIMMINIIMall=11111111 IMIIIIIIIIIIIEMNIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIII

INIIIIIIIIIIMIIIIII MINmozolinm =minMOMMIIIIIININIIIIIIIMMMI111111111 _IIIIIIIIIMI.P1111111111111111111IllifinignIMMINIIIIIMIIIIIIIIIIIIIIIIINIIIIIIIIIIIIIIIIMIIINIIIIIII

EdIMINIREMSIMMININMOIINIIIIIIIIIINIIIIIIINIIIMIIIIMINIIIIIININIIIIMI1111111111111111111 IIIIII IIIIIIIIIIIII.................ell WMPX/WMt MINIIMMINOONIMINIMI 01111011.11114101.1111111

Wed.Thurs.

Mon.

158

Wed.

TOTALS

40

19

Misoe Number

41

Table 2.3 Utilization of Departmental Instructional Area By Room


I. a. C 3 Weekly

b. C ] Alternating

c. C 3 Variable-

2. a. C 3 Semester Schedule Changeb. C No Semester Schedule Change


317 33 34 35

Room

No.or

Name

Day

of the

Week.

Morning

7:00 a.m.-12:00N

Afternoon

12:00N-60120p.m.4o. of

Hrs. Used

No. ofStud. Hrs.

Evening

_§LOOPAn.,No. of

Hrs. Used

No. oStud. Hrs.No. of

Hrs.Used

No. ofStud. Hrs.

I6A Mon.Tues.Wed.Thur.F 1.

LS C _ t.

TOT4LS

17A Mon.

.-------rzLz.-------=sg

Tues.Wed.Tt urs

Fri.

LS C Sat.

luTALS ...............-- -........

18A Mon.Tues.Wed.Thqr.Fr w.

LS C Sat.1111111111111

TOTALS 11.11 _

19A Mon. IIIIII.

Tues.Wed

Thurs.Fri.

L C Sa.ti1111/1111111

c. 3 Variable


31 433 J34 35

Room E

No.or

Name

Day

of the

Week.

Morning

7:00 a.m.-12:00N

Afternoon

12:00N-6:00No. of

Hrs. Used

p.m.No. of

Stud. Hrs.

Evening

6:00 P.M.-11:00No. of

Hrs. Used

p.m._No. ofStud. Hrs.

No. ofHrs.Used

No. ofStud. Hrs.

16A Mon.Tues.Wed.Thurs.Fri.

LS C Sat.

TOTALS -----

I7A Mon.Tues.Wed.Thurs.Fri.

LS C Sat,

TOTALS1

1OA Mon.Tues.Wed.

Thurs.Fri.

LS C Sa .

TOTALS

19A Mon.

Toes,Wed.Thurs.Fri.

LS C Sat.

TOTALS

20A Mon.

1111111111111

Tues.,_

Wed.Thurs.

Sat.

TOTALS 111111111111

4 2

20

43 Misoe Number

Table 2,3 tCont d) Utlitzahon of DepartMental Instructional Area by Room

Check Applicaboe Program Schedule

a. E Weeklyb.' [ Alternattngc. [ 3 Variable

2. a. [ Semester Schedule Changeb. C 3 No Semester Schedule Change

WEEKLY OR SCHEDULE 8

. .: 39 40

Room

No.pr

Name

Day

of the

Morning

7:00 a.m.-12:00N

Afternoon

12:00N-600 p.m.

Evening

6:00_2.m.-11:0ONo. of

Hrs. Used

p.m.

No. ofStud. Hrs.Week

No. ofHrs,Used

No. ofStud. Hrs

No. ofHrs. Used

No. ofStud. Hrs.

168 Mon.Tues.Wed.Thurs.Fri.

LS C Sat.

TOTALS

178,,

Mon.Tues.Wed.Thurs.Fri.

LS C Sat.

TOTALS

188 Mon.Tues.Wei.Thurs.Fri.

IS C Sat.

TOTALS1

198 Mon.Tues.

Wed.Thurs.Frt.

Ls C Sat,

TOTALS

11111111111111111111111111111111

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIUIIIIIII

208 MonoTues.

Room

No.or

Name

Day

of the

Morning

7:00 a.m.-12:00N

Afternoon

12:00N-6:00 p.m.

Eventng

6:00 p.m.-II:00 p.m.No. ofStud. Hrs.Week

Rb. ofHrs.Used

No. ofStud. Hrs

No. ofHrs. Used

No. ofStud. Hrs.

No. ofHrs. Used

16B Mon. I

Tues.Wed.Thurs.Fri.

LS G Sat.

IIIITOTALS

17B Mon.

.111111t111.11111Tues.Wed.Thurs.Fri.

TOTALS EMI1111111111.18B Mon.

Tues.Wed.

UMThurs.Fri.

11111

L C Sat.

TOTALS

19B Mon.Tues.Wed.Thurs.Fri.

C Sat.

TOTALS

20B Mon. IIIIIIIIIIIIIIIIIIIIIIIIII

11111111111111Tues."e.Thurs.ri.

L C a .

TOTALS

21.

4,

REPORTING TERMINAL PERFORMANCE OBJECTIVES (TERMOBS)

4GTABLE T-1

INSTRUCTIONAL DIVISION AND UNIT OUTLINE

DRAFTING PROGRAM

DOES THIS OUTLINE CONTAIN ALL OF THE INSTRUCTIONAL CONTENT OF YOURPROGRAM: YES NO

CODE DIVISION CODE UNIT

01 TOOLS AND SUPPLIES 01 PENCILS02 COMPASSES03 TRIANGLES04 REGULAR CURVES05 IRREGULAR, CURVES06 DIVIDERS07 RULING PENS08 SCALES09 DUCKS AND SPLINE10 PROTRACTOR11 TEMPLATES12 LEAD POINTER13 ERASING SHIELD14 PANTOGRAPH15 DUST BRUSHES16 CLEANING AGENTS17 MEDIA (PAPER)

02 MEASURING INSTRUMENTS 01 MICROMETERS02 VERNIER CALIPERS03 DEPTH GAUGES04 CALIPERS05 HEIGHT GAUGES06 THREAD GAUGES

03 EQUIPMENT 01 BOARDS02 DRAFTING MACHINES03 STRAIGHT EDGES04 HARDNESS TESTER05 TENSIL TESTER06 METALOGRAPHER MICROSCOPE07 TRANSIT

04 LETTERING 01 FREEHAND02 STENCILS03 TEMPLATES04 DECALS05 AIDS

05 LINE CONVENTIONS 01 OBJECT,02 HIDDEN03 CENTER04 PHANTOM05 SECTION06 DIMENSION07 EXTENSION08 LEADER09 CUTTING PLAN10 BREAK

06 GEOMETRIC CONSTRUCTION 01 STRAIGHT LINE4

07080910

-11121314

RULING PENSSCALESDUCKS AND .SPLINEPROTRACTORTEMPLATESLEAD POINTERERASING-SHIELDPANTOGRAPH-

15 DUST BRUSHES16 CLEANING AGENTS17 MEDIA (PAPER)

02 MEASURING INSTRUMENTS 01 MICROMETERS02 VERNIER CALIPERS03 DEPTH GAUGES04 CALIPERS05 HEIGHT GAUGES06 THREAD GAUGES'

03 EQUIPMENT- 01 BOARDS02 DRAFTING MACHINES03 STRAIGHT EDGES04 HARDNESS TESTER05 TENSIL TESTER06 METALOGRAPHER MICROSCOPE07 TRANSIT

04 LETTERING 01 FREEHAND02 STENCILS03 TEMPLATES04 DECALS05 AIDS

-05 LINE CONVENTIONS 01 OBJECT02 HIDDEN03 CENTER04 PHANTOM05 SECTION06 DIMENSION07 EXTENSION08 LEADER09 CUTTING PLAN10 BREAK

06 GEOMETRIC CONSTRUCTION . 01 STRAIGHT LINE02 POLYGON03 ARC04 CIRCLE05 CIRCLE AND LINE06 NONCIRCULAR

07 ORTHOGRAPHIC 01 SINGLE VIEW02 MULTI-VIEW

4"/

4

TABLE T-1


DRAFTING PROGRAM

CODE DIVISION

(CONTINUED)

CODE UNIT

08 DIMENSIONING 01 UNILATERAL02 ALIGNED03 ANGULAR04 FRACTIONAL05 DECIMAL06 METRIC07 COORDINATE0$ REFERENCE09 NOTATION10 CIRCULAR11 GEOMETRIC12 SCALE OF DRAWINGS13 CONVENTIONS

09 TOLERANCING 01 FRACTIONAL02 DECIMAL03 METRIC04 CLASSIFICATION OF FITS05 TRUE POSITIONING06 NOTATION07 ANGULAR08 ASSEMBLY

10 OBLIQUE 01 CAVALIER (SIMPLE)02 ARCS AND CURVES03 INCLINED SURFACES04 CABINET

11 ISOMETRIC 01 SIMPLE02 ARCS AND CURVES03 INCLINED SURFACES

2 PERSPECTIVE 01 SINGLE POINT02 TWO POINT03 THREE POINT04 SHADING

13 SKETCHING 01 PICTORIAL02 ORTHOGRAPHIC03 DESCRIPTIVE04 CONVENTIONS

14 SECTIONING 01 FULL02 HALF03 PARTIAL04 REMOVED05 CONVENTIONS06 OFFSET07 BROKEN OUT08 ALIGNED09 REVOLVED

05 DECIMAL06 METRIC07 COORDINATE08 REFERENCE09 NOTATION10 CIRCULAR11 GEOMETRIC12 SCALE OF DRAWINGS13 CONVENTIONS

09 TOLERANCING 01 FRACTIONAL02 DECIMAL03 METRIC04 CLASSIFICATION OF FITS05 TRUE POSITIONING06 NOTATION07 ANGULAR08 ASSEMBLY

10 OBLIQUE 01 CAVALIER (SIMPLE)02 ARCS AND CURVES03 INCLINED SURFACES04 CABINET

11 ISOMETRIC 01 SIMPLE02 ARCS AND CURVES03 INCLINED SURFACES

12 PERSPECTIVE 01 SINGLE POINT02 TWO POINT03 THREE POINT04 SHADING

13 SKETCHING 01 PICTORIAL02 ORTHOGRAPHIC03 DESCRIPTIVE04 CONVENTIONS

14 SECTIONING 01 FULL02 HALF03 PARTIAL04 REMOVED05 CONVENTIONS06 OFFSET07 BROKEN OUT08 ALIGNED09 REVOLVED10 ASSEMBLY'

15 THREADS 01 CONVENTIONS02 SPECIFICATIONS

4{)

T-3

50TABLE T-1


DRAFTING PROGRAM

(CONTINUED)


16 FASTENERS 01 THREADED02 CLINCH TYPE03 SPRING LOADED

MATERIALS04-05 KEYS06 PINS

17 SPRINGS 01 HELICAL02 FLAT

18 AUXILIARY VIEWS 01 PRIMARY02 MULTIPLE

19 REVOLUTIONS 01 PRIMARY PLANE02 MULTI-PLANE

20 INTERSECTIONS 01 PRISMS02 CYLINDERS03 CONES

.4 04 PYRAMIDS05 PRISMS AND CYLINDERS06 CONES AND CYLINDERS07 PRISMS AND PYRAMIDS08 CYLINDERS AND PYRAMIDS

21 DEVELOPMENTS 01 STRAIGHT LINES02 CURVED SURFACES03 COMBINATIONS04 MULTI-PIECED05 TRANSITION PIECES

22 GEARS 01 SPUR02 BEVEL03 MITER04 MISCELLANEOUS

23 CAMS 01 MOTIONS02 PLATE.03 FACE04 CYLINDRICAL05 FOLLOWERS06 CONJUGATS

24 WELDING 01 SYMBOLS02 SPECIFICATIONS03 FABRICATIONS

25 WORKING DRAWINGS 01 DETAIL02 ASSEMBLY03 FORMATS04 CASTING'05 PATTERN

0 N

17 SPRINGS 01 HELICAL02 FLAT

Ui

18 AUXILIARY VIEWS 01 PRIMARY02 MULTIPLE

19 REVOLUTIONS PRIMARY PLANE02 MULTI-PLANE

20 INTERSECTIONS 01 PRISMS02 CYLINDERS03 CONES04 PYRAMIDS05 PRISMS AND CYLINDERS06 CONES AND CYLINDERS07 PRISMS AND PYRAMIDS08 CYLINDERS AND PYRAMIDS

21 DEVELOPMENTS 01 STRAIGHT LINES0 2 CURVED. ;, SURFACES

03 COMBINATIONS04 MULTI-PIECED05 ' TRANSITION P IECES

22 GEARS 01 SPUR02 BEVEL0 3 MITER04 MISCELLANEOUS

23 CAMS 01 MOTIONS02 PLATE03 FACE04 CYLINDRICAL05 FOLLOWERS06 CONJUGATS

24 WELDING 01 SYMBOLS02 SPECIFICATIONS03 FABRICATIONS

25 WORKING DRAWINGS 01 DETAIL02 ASSEMBLY03 FORMATS04 CASTING05 PATTERN06 FORGING07 LAYOUT08 FABRICATION09 TOLERANCE STUDY

26 REPRODUCTION 01 MACHINES02 PAPERS03 FILMS04 FILING SYSTEMS05 MICROFILM

51

TABLE T-1


DRAFTING PROGRAM

(CONTINUED)


27

28

INKING

CHARTS AND GRAPHS

010203,04

010203040506

LINEWORKLETTERINGDEVICESTEMPLATES

BARLINEPIECOMPARISONILLUSTRATIVEMEDIA

29 ELECTRONIC-DRAFTING 01 COMPONENTS AND SYMBOLS02 SUPPLEMENTARY SYMBOLS03 DRAFTING AIDS04 BLOCK DIAGRAMS05 SINGLE-LINE DIAGRAMS06 STANDARD CIRCUIT LAYOUTS07 SCHEMATIC DIAGRAMS -

Oft DRAWING IDENTIFICATIONS09 SYSTEM DRAWINGS10 PICTORIAL DRAWINGS11 PRINTED CIRCUITS12 WIRING DIAGRAMS

99 MISCELLANEOUS

30 ARCHITECTURAL DRAFTING 01 PLAN VIEWS02 ELEVATIONS03 SECTIONS04 DETAILS05 ALTERATIONS06 ADDITIONS07 TYPES OF CONSTRUCTION08 ENGINEERING09 SPECIFICATIONS10 CONTRACTS11 ESTIMATING12 SKETCHING13 DISPLAY DRAWINGS14 PERSPECTIVE15 MOCK-UPS AND MODELS16 ELECTRICAL SPECIFICATIONS

31 MANUFACTURING PROCESS 01 MACHINE SHOP

32 PIPING DRAWING 01 MATERIALS.02 SYMBOLS

33 DESIGN DRAFTING 01 JIGS AND FIXTURES

99 MISCELLANEOUS 01 MACHINE SHOP

TABLE T-2

TERMOB DIVISION AND UNIT OUTLINE

DRAFTING PROGRAM

DOES THIS OUTLINE CONTAIN ALL TOPICS IN WHICH GRADUATES ACQUIRE JOB-

ENTRY

CODE

SKILLS: YES NO

UNITDIVISION CODE

01 SKETCHING 01020304

ISOMETRICOBLIQUEORTHOGRAPHICPERSPECTIVE

02 NOTATIONS '01 DIMENSIONING02 .TOLERANCING03 WELDING SYMBOLS04- LINE CONVENTIONS

03 SECTIONING 01 FULL02 HALF03 REMOVED04 OFFSET05 BROKEN OUT06 REVOLVED07 ARCHITECTURAL

04 DEVELOPMENTS 01 CURVED SURFACES02 COMBINATIONS03 TRANSITION PIECE

'05 AUXILIARY VIEWS 01 PRIMARY02 SECONDARY

06 ° - WORKING DRAWINGS 01 DETAIL DRAWING02 ,ASSEMBLY DRAWING03 bIAGRAM DRAWING04 CONSTRUCTION DRAWING

53

41)

TERMINAL PERFORMANCE OBJECTIVES (TERMOBS)

and

REPORTING FORMS

54

MI SOE NO. .11=n1}14,,.

PROGRAM DRAFTING DiraION 01 SKETCHING

1.00 CONDITION

UNIT 01 ISOMETRIC

TERMOB NO. 10-001

( ) 1.01 TWO VIEW DRAWING OF BEARING WITH IRREGULAR CURVE( ) 1.02 BASTC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

GENERAL-STATEMENT -0FLL-PERFO

( ) 2.01 'KE I V T Z4 A k EMPLOYING THEFOLLOWING PROCEDURE:

( ) i.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF LAYOUT FOR POSITIONING( ) 2.04 ESTABLISH BASELINE IN ISOMETRIC VIEW( ) 2.05 ESTABLISH REMAINING TWO AXES( ) 2.06 PLOT VERTICAL COORDINATES ON ORIGINAL CU -(TWO VIEW

DRAWING)( ) 2.07 PLOT CORRESPONDING COORDINATES ON ISOMETRIC DRAWING( ) 2.08 DRAW CURVE ON ISOMETRIC DRAWING( ) 2.09 COMPLETE DRAWING

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01 DRAWING MUST CLEARLY ILLUSTRATE CONSTRUCTION OF

BEARING TO SATISFACTION OF BOARD OF EXPERT RATERS.CORRECT DRAFTING PROCEDURE WILL BE FOLLOWED WITHTHE PERFORMANCE OF EACH STEP JUDGED AS SATISFACTORYOR UNSATISFACTORY. ALL STEPS TO BE COMPLETEDWITHIN 3 HOURS.

( ), 3.02 MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3A)( ) 3.03- DRAWING MUST BE CENTERED ON LAYOUT( ) 3.04 LINE 300 FROM HORIZONTAL( ) 3.05 AT 30° FROM HORIZONTAL AND VERTICAL RESPECTIVELY( ) 3.06 MUST BE CLOSE ENOUGH TO GIVE ACCURATE REPRESENTATION

OF CURVEC ) 3.07 MUST BE REPRODUCED ACCURATELY( ) 3.08 ALL COORDINATES MUST BE EMPLOYED( ) 3.09 ALL OTHER DETAILS MUST BE INDICATED

5 5

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

MISOE NO.

DIVISION 01 SKETCHING

UNIT 01 ISOMETRIC

TERMOB NO. 10-001

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION


UNIT 01

TERMOB NO. 10-002

( ) 1.01 TWO VIEW DRAWING OF ARM BRACKET( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

GE OF-PERFORMANCE 011- iw'

( ) 2.01 MAKE ISQMETRIC_DRAWING OF AMMLpRACKET EMPLOYING THEFOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF LAYOUT FOR POSITIONING

( ) 2.04 ESTABLISH BASE LINE IN ISOMETRIC VIEW

( ) 2.05 ESTABLISH REMAINING TWO AXES( ) 2.06 PLOT VERTICAL COORDINATES ON ORIGINAL CURVES

(ON TWO VIEW DRAWING)( ) 2.07 PLOT CORRESPONDING COORDINATES ON ISOMETRIC DRAWING

( ) 2.08 DRAW CURVE ON ISOMETRIC DRAWING

( ) 2.09 ESTABLISH COORDINATES FOR PLACEMENT AND SIZE OF HOLE

(ON TWO VIEW DRAWING)( ) 2.10 PLOT SIZE AND PLACEMENT OF HOLES ON ISOMETRIC DRAWING

( ) 2.11 COMPLETE DRAWING

3.00 EXTENT


) 3.01 DRAWING MUST CLEARLY ILLUSTRATE CONSTRUCTION OF ARMBRACKET TO SATISFACTION OF BOARD OF EXPERT RATERS.CORRECT DRAFTING PROCEDURE WILL BE FOLLOWED WITHTHE PERFORMANCE OF EACH STEP JUDGED AS SATISFACTORY

OR UNSATISFACTORY. ALL STEPS TO BE COMPLETEDWITHIN 4 HOURS.

) 3.03 MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3A)

( ) 3.04 LINE 30° FROM HORIZONTAL( ) 1.05 LINES AT 30° FROM HORIZONTAL AND VERTICAL RESPECTIVELY

( ) 3.06 MUST BE CLOSE ENOUGH TO GIVE ACCURATE REPRESENTATIONOF DRAWING

( ) 3.07 MUST BE REPRODUCED ACCURATELY( ) 3.08 ALL COORDINATES MUST BE EMPLOYED

( ) 3.09 VERTICAL AND HORIZONTAL COORDINATES MUST BE MEASURED

( ) 3.10 HOLES MUST BE CONSTRUCTED IN ISOMETRIC ACCORDING TOCORRECT PROCEDURE FOR ISOMETRIC DRAWING

( ) 3.11 ALL OTHER DETAILS MUST BE ADDED

PROGRAM DRAFTING

USOE CODE NOM

1.00 CONDITION

MISOE NO.


UNIT 01 fsomETAic

TERMOH NO. 10 --002

2.00 PERFORMANCE


3.00 EXTENT

GENERAL STATEMENT OF; XTENT AND EXTENT OF RESULTING OUTCOME

MISOE NO.

PROGRAM DRAFTING DIVISION 01 SKETCHING

1.00 CONDITION

UNIT 01 ISOMETRIC

TERMOB NO. 10-003

( ) 1.01 TWO VIEW DRAWING OF WEDGE BLOCK( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

-2.00 PERFORMANCE

JERAL- STA ND-RESULTING-OUTCOME( ) 2.01 MAKE ISOMETRIC DRAWING OF WEDGE BLOCK EMPLOYING THE

FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF LAYOUT FOR POSITION( ) 2.04 ESTABLISH BASE LINE IN ISOMETRIC VIEW( ) 2.05 ESTABLISH REMAINING TWO AXES( ) 2.06 CONSTRUCT RHOMBOID FOR PROPORTIONING OF PIECE( ) 2.07 TRANSFER MEASUREMENTS FROM TWO VIEW DRAWING TO

ISOMETRIC( ) 2.08 COMPLETE DRAWING

3.00 EXTENT


( ) 3.01 DRAWING MUST CLEARLY ILLUSTRATE MAKE-UP OF WEDGE BLOCKTO SATISFACTION OF BOARD OF EXPERT RATERS. CORRECTDRAFTING PROCEDURE WILL BE FOLLOWED WITH THEPERFORMANCE OF EACH STEP JUDGED AS SATISFACTORY ORUNSATISFACTORY. ALL STEPS TO BE COMPLETED WITHIN11/2 HOURS.

( ) 3.02 MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3A)( ) 3.03 DRAWING MUST BE CENTERED ON LAYOUT( ) 3.04 THIS LINE 30° FROM HORIZONTAL( ) 3.05 THESE AT 300 FROM HORIZONTAL AND ON VERTICAL RESPECTIVELY( ) 3.06 MEASUREMENTS MUST BE TAKEN FROM TWO VIEW DRAWING TO

ESTABLISH PROPORTIONSi 3.07 THESE MUST BE REPRODUCEBk ACCURATELY 59

( ) 3.08 SUPPLY ALL DETAILS AND NOTATIONS

MISOE NO.


USOE CODE NO(S) UNIT 01 ISOMETRIC

TERMOB NO.

1.00 CONDITION

2.00 PERFORMANCE

10-003


3.00 EXTENT


GO

M1SOE-NO.

PROGRAM DRAFTIN, DIVISION ,_01 SKETCHING

UNIT 01 OMETRIC

1.00 CONDITION

TERMOB NO. 10-004

( ) 1.01 SECTIONAL ELEVATION DRAWING OF PIPE LAYOUT INRESIDENTIAL BUILDING

( ) 1.02 ISOMETRIC PIPE TEMPLATE( ) 1.03 BASIC DRAFTING SUPPLIES (TABLE T-3)

2.00 *PERFORMANCE.

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE A SINGLE LINE ISOMETRIC DIAGRAM DRAWING OF

PIPE LAYOUT ACCORDING TO THE FOLLOWING PROCEDURE:

( 2.02 DRAW TITLE BLOCK( ) 2.03 CONSTRUCT ALL VERTICAL LINES TO SCALE OF 1/8" = 1'

( ) 2.04 CONSTRUCT ALL HORIZONTAL LINES AT 300 ANGLE ANDSCALE OF 1/8" = 14 4

( ) 2.05 PLACE SYMBOLS WHERE REQUIRED USING ISOMETRIC PIPE

( ) 2.06TEMPLATE,

DESIGNATE PIPE SIZES AND CODE NAMES( ) 2.07 ADD LIST OF MATERIALS REQUIRED( ) 2.08 DARKEN LINES AND ADD NOTATIONS

3.00 EXTENT


( ) 3.01 DRAWING DIAGRAM MUST ACCURATELY PORTRAY LAYOUT OFPIPE LINES FOR ASSEMBLY PURPOSES. EACH STEP TOBE JUDGED SATISFACTORY OR UNSATISFACTORY BY BOARDOF EXPERT RATERS. ALL STEPS TO BE COMPLETED WITHIN3 HOURS."

g MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3A

( ) 3.03 PIPE LENGTHS ARE DETERMINED FROM CENTER TO CENTERDISTANCES OF PIPE FITTINGS

( ) 3.04 CONSIDERATION TAKEN TO DISTRIBUTE DRAWING EVENLY ON

PAPER( )- 3.05 TEMPLATE SCALE TO BE 1/8" =( ) 3.06 PIPE SIZES AND CODE NAMES OF FITTINGS PLACED NEXT'

TO PARTS CONCERNED( ) 3.07 A COMPLETE LIST OF MATERIALS IS REQUIRED

( ) 3.08 LINES TO BE DARK, SHARP AND OF PROPER WEIGHT

GI

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 -CONDITION

2.00 PERFORMANCE

MISOE NO.


UNIT 01 ISOMETRIC

TERMOB NO. 10 -004


3.00 EXTENT


MLSOE NO.

PROGRAM-- DRAFTING DIVISION 01 SKETCHING

1.00 CONDITION

UNIT 02 OBLIQUt

TERMOB NO. 10-005

( ) 1.01 TWO VIEW DRAWING OF BEVELED BLOCK( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

GENERAL STATEMENT OP PERFORMANCE AND RESULTING OUTCOME

( ) 2.01 MAKE OBLIQUE DRAWING OF BEVELED BLOCK ACCORDING TOFOLLOWING PROCEDURE:

( ). 2.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF LAYOUT FOR POSITIONING( ) 2.04 SET OFF HEIGHT, WIDTH AND DEPTH( ) 2.05 LAY OUT FRONT FACE IN TRUE SIZE AND SHAPE( )

2006 DRAW LINES THROUGH ESTABLISHED CORNERS TO RECEDING AXIS

3.00 EXTENT


C ) 3.01 DRAWING MUST CLEARLY ILLUSTRATE CONSTRUCTION OF BEVELEDBLOCK TO SATISFACTION OF BOARD OF EXPERT RATERS.CORRECT DRAFTING PROCEDURES WILL BE FOLLOWED WITHTHE PERFORMANCE OF EACH STEP JUDGED AS SATISFACTORYOR UNSATISFACTORY. ALL STEPS TO BE COMPLETED WITHIN11/2 HOURS.

( ) 3.02 MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3A)

( ) 3.03 DRAWING MUST BE CENTERED ON LAYOUT( ) 3.04 THESE MEASUREMENTS MUST BE ACCURATELY REPRODUCED FROM

TWO VIEW DRAWING( ) 3.05 THESE MEASUREMENTS MUST BE ACCURATELY REPRODUCED FROM

TWO VIEW DRAWING( ) 3.06 RECEDING AXIS LINES MUST BE PARALLEL

a

PROGRAM DRAFTING

USOE CODE. NO(S)

1.00 'CONDITION

2.00 PERFORMANCE

MISOE NO.

DIVISION SKETCHING

UNIT 02 OBLIQUE

TERMOB NO. 10-005


3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF.RESULTING OUTCOME

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION


UNIT 02 OBLIQUE

TERMOB NO. 10-006

( ) 1.01 TWO VIEW DRAWING OF INDEX GUIDE( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME-----11 2.0I-MAKE-OBLIQUE-DRAWING-OF-INDEX-GUlDE-ACCORDING-TO THEE


. +2 DRAW TITLE BLOCK( ) 2-.03 MAKE ROUGH SKETCH OF LAYOUT FOR POSITIONING( ) 2.04 SET OFF HEIGHT, WIDTH AND DEPTH( ) 2.05 LAY OUT FRONT FACE IN TRUE SIZE AND SHAPE( ) 2.06 DRAW LINES THROUGH ESTABLISHED CORNERS TO RECEDING

AXIS

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01 DRAWING MUST CLEARLY ILLUSTRATE CONSTRUCTION OF INDEX

GUIDE TO SATISFACTION OF BOARD OF EXPERT RATERS.CORRECT DRAFTING PROCEDURES WILL BE FOLLOWED WITHTHE PERFORMANCE OF EACH STEP JUDGED AS SATISFACTORYOR UNSATISFACTORY. ALL STEPS TO BE COMPLETED WITHIN3 HOURS.

) 3.02 MUST CONTAIN ALL PERTINENT INFORMATION TABLE T A) 3.03 DRAWING SHOULD BE CENTERED ON LAYOUT) 3.04 THESE MEASUREMENTS MUST BE ACCURATELY REPRODUCED FROM

TWO VIEW DRAWING) 3.05 THESE MEASUREMENTS MUST BE ACCURATELY REPRODUCED FROM

TWO VIEW DRAWING) 3.06 RECEDING AXIS LINES MUST BE PARALLEL

MISOE NO.


USOE CODE NO(S) UNIT 02 OBLIQUE

TERMOB NO. 10-006

1.00 CONDITION

2.00 PERFORMANCE


3.00 EXTENT


MISOE NO, 11110.,...PROGRAM DRAFTING DIVISION 01 SKETCHING

1.00 CONDITION

UNIT '02 OBLIQUE

TERMOLNO. 10-007

( ) 1.01 TWO VIEW DRAWING OF CONTROL BRACKET

( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

*2.00 PERFORMANCE


) 2.01 MAKE OBLIQUE DRAWING OF CONTROL BRACKET ACCORDING TOTHE FOLLOWING PROCEDURE:


( ) 2.04 SET OFF HEIGHT, WIDTH AND DEPTH( ) 2.05 LAY OUT FRONT FACE IN TRUE SIZE AND SHAPE

( ) 2.06 DRAW LINES THROUGH ESTABLISHED CORNERS TO RECEDING AXIS

3.00 EXTENT


( ) 2.01 DRAWING MUST CLEARLY ILLUSTRATE CONSTRUCTION OF CONTROLBRACKET TO SATIFACTION OF BOARD OF EXERT RATERS.CORRECT DRAFTING PROCEDURES WILL BE FOLLOWED WITHTHE PERFORMANCE OF EACH STEP JUDGED AS SATISFACTORYOR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN 3 HOURS.


( ) 3.03 DRAWING SHOULD BE CENTERED ON LAYOUT

( ) 3.04 THESE MEASUREMENTS MUST BE ACCURATELY REPRODUCED FROMTWO VIEW DRAWING

( ) 3.05 THESE MEASUREMENTS MUST BEACCURATELY REPRODUCED FROMTWO VIEW DRAWING

( ) 3.06 RECEDING AXIS LINES MUST BE PARALLEL

Cr'

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

MISOE NO.


UNIT 02 OBLIQUE

TERMOB NO. 10-007

2.00 PERFORMANCE


3.00 EXTENT


MISOE NO.


1.00 CONDITION

UNIT 03 ORTHOGRAPHIC

TERMOB NO. 10-008

,(,) 1.01 ISOMETRIC DRAWING OF SHAFT SUPPORT( ) 1.02 SOFT LEAD PENCIL WITH MEDIUM CONE SHAPED POINT( ) 1.03 SIZE "A" GRAPT.DAVER WITH 1/4" SQUARES

2.0.0 PERFORMANCE


( ) 2.01 MAKE A TWO VIEW SKETCH OF SHAFT SUPPORT ACCORDING TOTHE FOLLOWING PROCEDURE:

( ) 2.02 SKETCH TITLE BLOCK( ) 2.03 LAY OUT THE BASIC RECTANGLES REQUIRED AND DRAW OUTLINE

TO OVERALL SKETCH SIZES( ) 2.04 DRAW CENTER LINE FOR HOLE( ) 2.05 LAY OUT RECTANGLES FOR ARCS AND CIRCLE( ) 2.06 LOCATE DOTS AND SKETCH ARCS AND CIRCLE( ) 2.07 DIMENSION SKETCH AND ADD NOTATIONS REQUIRED( ) 2.08 DARKEN ALL OBJECT LINES TO COMPLETE SKETCH

3.00 EXTENT


( ) 3.01 SKETCH MUST CLEARLY ILLUSTRATE FORM AND DIMENSIONS OFSHAFT SUPPORT FOR MANUFACTURING PURPOSES. EACHSTEP TO_BE JUDGED AS ACCEPTABLE OR NOT ACCEPTABLEBY BOARD OF EXPERT RATERS. ALL STEPS TO BE COMPLETEWITHIN ONE HOUR.

( ) 3.02 MUST CONTAIN ALL PERTINENT INFORMATION( ) 3.03 VIEWS TO BE EVENLY DISTRIBUTED ON PAPER( ) 3.04 CENTER LINE DETERMINED FROM ISOMETRIC DRAWING( ) 3.05 SQUARES ON GRAPH PAPER TO BE USED AS GUIDES( ) 3.06 LINES TO BE CONSTRUCTED LIGHTLY( ) 3.07 DIMENSIONS TO BE TRANSFERRED FROM ISOMETRIC DRAWING( ) 3.08 LINE WORK TO BE SHARP, DARK, AND OF PROPER WEIGHT

69

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

MISOE NO.


UNIT 03 ORTHOGRAPHIC

TERMOB NO. 10-008

GENERA, STATEMENT OF PERFORMANCE AND RESULTING OUTCOME

3.00 EXTENT


7

It

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION


UNIT 04 PERSPECTIVE

TERMOB NO. 10-009

( ) 1.01 TWO VIEW DRAWING OF STEP BLOCK( ) 1.02 SOFT PENCIL WITH MEDIUM CONE SHAPED POINT

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE A TWO POINT PERSPECTIVE SKETCH OF STEP BLOCK

ACCORDING TO THE FOLLOWING PROCEDURE:

( ) 2.02 CONSTRUCT TITLE BLOCK( ) 2.03 SKETCH FRONT CORNER OF STEP BLOCK'S TRUE HEIGHT( ) 2.04 LOCATE TWO VANISHING POINTS AND ESTABLISH HORIZON( ) 2.05 ESTIMATE WIDTH AND DEPTH AND SKETCH ENCLOSING BOX( ) 2.06 BLOCK IN THE RIGHT-ANGLED NOTCH( ) 2.07 DARKEN OBJECT LINES TO COMPLETE DRAWING

3.00 EXTEN

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01 SKETCH MUST CLEARLY ILLUSTRATE TRUE APPEARANCE OF

STEP BLOCK. CORRECT DRAFTING PROCEDURES WILL BEFOLLOWED AND EACH STEP JUDGED SATISFACTORY ORUNSATISFACTORY BY BOARD OF4EXPERT RATERS.

( ) 3.02 MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3A)( ) 3.03 HEIGHT MUST BE ESTIMATED FROM TWO VIEW DRAWING( ) 3.04 VANISHING POINT AND HORIZON SELECTED FOR BEST GRAPHIC

REPRESENTATION( ) 3.05- FORESHORTENING MUST BE CONSIDERED WHEN ESTIMATING

WIDTH AND DEPTH( ) 3.06 DIMENSIONS ESTIMATED FROM TWO VIEW DRAWING( ) 3.07 LINES TO BE SHARP, DARK, AND OF EVEN WEIGHT

71

PROGRAM DRAFTING DIVISION 01

MISOE NO.

SKETCHING

USOE CODE NO(S) UNIT 04 PERSPECTIVE

TERMOB NO. 10-009

1.00 CONDITION

2.00 PERFORMANCE


3.00 EXTENT


7 2

mIspE NO.

PROGRAM DRAFTING

1.00 CONDITION


UNIT 04 PERSPECTIVE

TERMOB NO. 10 -010

( ) 1.01 TWO VIEW DRAWING OF BOX PARALLEL( ) 1.02 SOFT PENCIL WITH MEDIUM CONE SHAPED POINT

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE A ONE POINT PERSPECTIVE SKETCH OF BOX PARALLEL


( ) 2.02 CONSTRUCT TITLE magi(( ) 2.03 ESTIMATE AND SKETCH FRONT FACE AS IN ORTHOGRAPHIC

DRAWING( ) 2.04 SELECT VANISHING POINT AND HORIZON FOR CONVERGING

DEPTH LINES( ) 2.05 SKETCH DEPTH LINES TOWARD VANISHING POINT( ) 2.06 CUT OFF ALL DEPTH LINES TO DESIRED LENGTH( ) 2.07 DARKEN OBJECT LINES TO COMPLETE SKETCH

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01 SKETCH MUST CLEARLY ILLUSTRATE TRUE APPEARANCE OF

PARALLEL. CORRECT DRAFTING PROCEDURES WILL BEFOLLOWED AND EACH STEP JUDGED SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN ONE HOUR.

BOX

( ) 3.02 MUST CONTAIN ALL PERTINENT INFORMATION( ) 3.03 LENGTH AND HEIGHT MUST BE ESTIMATED FROM TWO VIEW

DRAWING) 3.04 VANISHING POINT SELECTED FOR BEST GRAPHIC REPRESEN-

'

TATION( ) 3.05 ILLUSTRATION MUST BE -EVENLY DISTRIBUTED ON PAPER( ) 3.06 FORESHORTENING TO BE CONSIDERED WHEN ESTIMATING DEPTH( ) 3.07 LINES TO BE SHARP, DARK, AND OF EVEN WEIGHT

'?3

PROGRAM DRAFTING

USOE CODE NO(S)

1,00 CONDITION

2.00 PERFORMANCE

DIVISION 01

MISOE NO.

SKETCHING

UNIT 04 PERSPECTIVE

TERMOB NO.. 10-010


3.00 EXTENT


74

MISOE NO.


UNIT 04 PERSPECTIVE

TERMOD NO. 10 -011

1.00 CONDITION

( ) 1.01 THREE VIEW DRAWING OF COTTAGE( ) 1.02 BASIC DRAFTING SUPPLIES

2.0`0 PERFORMANCE


( ) 2.01 MAKE AN ANGULAR PERSPECTIVE DRAWING OF COTTAGEEMPLOYING THE FOLLOWING PROCEDURE:

( ) 2.02 DRAW THE PICTURE PLANE LINE, HORIZON, AND GROUND LINE( ) 2.03 DRAW SIDE VIEW OF COTTAGE AND LOCATE STATION POINT( ) 2.04 LOCATE VANISHING POINTS AND TRUE HEIGHTS LINE( ) 2.05 DRAW VISUAL RAYS FROM STATION POINTS TO VARIOUS POINTS

IN TOP VIEW( ) 2.06 LOCATE WINDOW AND DOOR( ) 2.07 DARKEN ALL OBJECT LINES TO COMPLETE DRAWING

3.00 EXTENT


( ) 3.01 DRAWING MUST CLEARLY ILLUSTRATE TRUE PERSPECTIVE OFCOTTAGE. EACH STEP WILL BE JUDGED AS SATISFACTORYOR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN 4 HOURS.

( ) 3.02 FRONT CORNER OF COTTAGE (TOP VIEW) TO TOUCH PICTUREPLANE LINE AND DRAWN AT A 300 ANGLE.

( ) 3.03 DIMENSIONS TRANSFERRED FROM THREE VIEW DRAWING( ) 3.04 VANISHING POINTS SELECTED TO ILLUSTRATE COTTAGE TO

BEST ADVANTAGE( ) 3.05 LINES MUST BE THIN, LIGHT, AND ACCURATE( ) 3.06 TRUE HEIGHTS TRANSFERRED FROM SIDE VIEW( ) 3.07 LINES TO BE SHARP, DARK, AND CT EVEN WEIGHT

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

MISOE NO.


UNIT 04 PERSPECTIVE

TERMOB NO. 10-011


Igo

3.00 EXTENT


'76

MISOE NO.

PROGRAM DRAFTING DIVISION 02 NOTATIONS

1.00 CONDITION

UNIT 01 DIMENSIONING

TERMOB NO. 10-012

( ) 1.01 DETAIL DRAWINGS OF MACHINIST'S CLAMP WITHOUT

DIMENSIONS( ) 1.02 MACHINIST'S CLAMP( ) 1.03 MICROMETER (0 TO 1 INCH)

( ) 1.04 VERNIER CALIPER( ) 1.05 THREAD GAUGE

2.00 PERFORMANCE


( ) 2.01 DETERMINE DIMENSIONS OF MACHINIST'S CLAMP TO THE


( ) 2.02 TAKE MEASUREMENTS WITH MICROMETER

( ) 2.03 TAKE MEASUREMENTS WITH VERNIER CALIPER

( ) 2.04 DETERMINE THREAD SIZE

3.00 EXTENT


( ) 3.01 DIMENSIONS OF MACHINIST'S CLAMP ARE DETERMINED.PERFORMANCE OF EACH STEP JUDGED SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALL

STEPS TO BE COMPLETED WITHIN TEN MINUTES.

( ) 3.02 DIMENSIONS MUST BE ACCURATE TO ± .001


( ) 3.04 DIMENSIONS MUST COMPLY WITH SPECIFIC THREAD STANDARD

77

PROGRAM DRAFT;Ng.

MISOE NO.

DIVISION 02 NOTATIONS

USOE CODE NO (S) UNIT 01 SE_MISMINQ_,_rDif...

TERMOB NO. 107012

1.00 CONDITION

2.00 PERFORMANCE


3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF .RESULTING OUTCOME

MISOE NO.


1.00 CONDITION


TERMOB NO. 10-013

( ) 1.01 DETAIL DRAWING OF A "T" BRACKET WITHOUT DIMENSIONS( ) 1.02 "T" BRACKET( ) 1.03 VERNIER CALIPER( ) 1.04 CALIPER( ) 1.05 HEIGHT GAUGE (VERNIER SCALE)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) .2.01 DETERMINE DIMENSIONS OF A "T" BRACKET TO THE


( ) 2.02 TAKE MEASUREMENTS WITH VERNIER CALIPER( ) 2.03 TAKE MEASUREMENTS WITH CALIPER( ) 2.04 TAKE MEASUREMENTS WITH HEIGHT GAUGE

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME) 3.01 DIMENSIONS OF "T" BRACKET ARE DETERMINED. PERFORMANCE

OP EACH STEP OF PROCEDURE JUDGED SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN TEN MINUTES.

( ) 3.02 DIMENSIONS MUST BE ACCURATE TO 1 1/64( ) 3.03 DIMENSIONS MUST BE ACCURATE TO ± 1/64( ) 3.04 DIMENSIONS MUST BE ACCURATE TO 1/64

'MISOE NO.


USOE CODE NO(S) UNIT 01 DIMENSIONING

TERMOB NO. 10-013

1.00 CONDITION

2.00 PERFORMANCE

GENERAL STATEMENT Or PERFORMANCE AND RESULTING OUTCOME

3.00 EXTENT

..,-----"GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME

MISOE NO.



TERMOB NO. 10-014

1.00 CONDITION

( ) 1.01 DETAIL DRAWINGS OF A LATHE CENTER WITHOUT DIMENSIONS

( ) 1.02 LATHE CENTER( ) . 1.03 HEIGHT GAUGE (DIAL SCALE)

( ) 1.04 CONTACT PROTRACTOR (GONIOMETER)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND SULTING OUTCOME

( ) 2.01 DETERMINE DIMENSIONS OF LPHE CENTER TO THE FOLLOWING

PROCEDURE:

( ) 2.02 TAKE MEASUREMENTS WITH HEIGHTGAUGE

( ) 2.03 TAKE MEASUREMENTS WITH GONIOMETER

3.00 EXTENT

NEPAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME

( ) 3.01 DIMENSIONS OF LATHE CENTER ARE DETERMINED. PERFORMANCE

OF EACH STEP JUDGED SATISFACTORY OR UNSATISFACTORY

BY BOARD OF EXPERT RATERS. ALL STEPS TO BE

COMPLETED WITHIN TEN MINUTES.


( ) 3.03 DIMENSIONS MUST BE ACCURATE TO 4' 1/20

81

MISOE NO.

PROGRAM DRAFTIng DIVISION 02 NOTATIONS

USOE CODE NO(S) UNIT 01 15-1EIMATIM-------

TERMOB NO. 10414

1.00 CONDITION

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND, RESULTING OUTCOME

3.00 EXTENT


82.

MISOE" NO. limr.,,

PROGRAM DRAFTING , DIVISION 02 NOTATIONS

1.`00 CONDITION

UNIT 01 DIMENSIONIN3

TERMOB NO. 10-015

( ) 1.01 D L DRAWINGS OF,STAYROD PIVOT WITHOUT DIMENSIONS

( ) 1.02 BA C DRAFTSMEN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE


( ) 2.01 DIMENSION STAYROD PIVOT ACCORDING TO FOLLOWINGPROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 PLACE SIZE DIMENSIONS ON EACH GEOMETRIC COMPONENT IN

ALL VIEWS DIMENSIONING RADII FIRST

( ) 2.04 SELECT CENTER LINES AND SURFACES

( ) 2.05 PLACE LOCATION DIMENSIONS ON GEOMETRICAL COMPONENTS

( ) 2.06 DIMENSION HOLE LOCATIONS( ) 2.07 ADD OVERALL DIMENSIONS AND NOTES

( ) 2.08 NOTE WELDING SYMBOLS( ) 2.09 ADD MATERIALS LIST INCLUDING THREAD SIZES FROM

NATIONAL COURSE CATALOG

3.00 EXTENT..,


( ) 3.01 DIMENSIONS WILL BE COMPLETE SO AS TO AFFORD MANU-FACTURE OF PIECE. CORRECT DRAFTING PROCEDURESWILL BE FOLLOWED WITH THE PERFORMANCE OF EACHSTEP JUDGED SATISFACTORY OR UNSATISFACTORY BYBOARD OF EXPERT RATERS. ALL STEPS TO BE COMPLETEDWITHIN 3 HOURS.

( ) 3.02 ALL PERTINENT INFORMATION MUST BE LISTED (TABLE T-3A)

( ) 3.03 DIMENSIONS MUST BE ACCURATE TO ± 1/64"

( ) 3.04 CENTER LINE MUST BE PROVIDED FOR ALL GEOMETRIC

COMPONENTS( ) 3.05 DIMENSIONS MUST BE ACCURATE TO ± 1/64"


( ) 3.07 MAJORITY OF DIMENSIONS SHOULD BE SUPPLIED ON PRINCIPAL

VIEW( ) 3.08 WELDING SYMBOLS MUST CORRECTLY REFLECT CONSTRUCTION

OF PIECE( ) 3.09 ALL PURCHASED. PARTS AS WELL AS MATERIALStMUST BE LISTED

83

MISOE NO.



-1.00 CONDITION

2.00 PERFORMANCE

TERMOB NO. 10 -015


3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF SULTING OUTCOME

MISOE NO.

PROGRAM. DRAFTING DIVISION 02 NOTATIONS


TERMOB NO. 10-016

1.00 CONDITION

( ) 1.01 DETAIL DRAWINGS OF MACHINIST'S CLAMP WITHOUT DIMENSIONS


2.00 PERFORMANCE


( ) 2.01 DIMENSION MACHINIST'S CLAMP ACCORDING TO FOLLOWINGPROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 PLACE SIZE DIMENSIONS ON EACH GEOMETRIC COMPONEi4T IN

ALL VIEWS, DIMENSIONING RADII FIRST( ) 2.04 SELECT CENTER LINES AND SURFACES( ) 2.05 PLACE LOCATION DIMENSIONS ON GEOMETRICAL COMPONENTS

( ) 2.06 DIMENSION HOLE LOCATIONS( ) 2.07 ADD OVERALL DIMENSIONS AND NOTES( ) 2.08 ADD MATERIALS LIST INCLUDING THREAD SIZES FROM

NATIONAL COURSE CATALOG

3.00 EXTENT


( ) 3.01 DIMENSIONS WILL BE COMPLETE SO AS TO AFFORD MANUFACTUREOF PIECE. CORRECT DRAFTING PROCEDURE WILL BEFOLLOWED WITH THE PERFORMANCE OF EACH STEP JUDGEDAS SATISFACTORY OR UNSATISFACTORY BY BOARD OFEXPERT RATERS. ALL STEPS TO BE COMPLETED WITHINIA HOURS.

( , 3.02 ALL PERTINENT INFORMATION MUST BE LISTED (TABLE T-3A)


( ) 3.04 CENTER LINE MUST BE PROVIDED FOR ALL GEOMETRICCOMPONENTS

( ) 3.05 DIMENSIONS MUST BE ACCURATE TO ± 1/64"( ) 3.06 DIMENSIONS MUST BE ACCURATE TO 1: .005


VIEW( ) 3.08 ALL PURCHASED PARTS AS WELL AS MATERIALS MUST BE LISTED

8 5

MISOE NO.



LOO CONDITION

2.00 PERFORMANCE

TERMOB NO. 10-016


3.00 EXTENT


86

MISOE NO.


1.00 CONDITION


TERMOB NO. 10-017

( ) 1.01 DETAIL DRAWINGS OF DRILL PRESS SPINDLE WITHOUT DIMENSIONS


2.00 PERFORMANCE


) 2.01. DIMENSION DRILL PRESS SPINDLE ACCORDING TO FOLLOWINPROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 PLACE SIZE DIMENSIONS ON EACH GEOMETRIC COMPONENT IN

ALL VIEWS, DIMENSIONING RADII FIRST( ) 2.04 SELECT CENTER LINES AND SURFACES( ) 2.05 PLACE LOCATION DIMENSIONS ON GEOMETRICAL COMPONENTS

( ) 2.06 DIMENSION HOLE LOCATIONS( ) 2.07 ADD OVERALL DIMENSIONS AND NOTES( ) 2.08 ADD MATERIALS LIST

3.00 EXTENT


( ) 3.01 DIMENSIONS WILL BE COMPLETE SO AS TO AFFORD MANUFACTUREOF PIECE. CORRECT DRAFTING PROCEDURES WILL BEFOLLOWED WITH THE PERFORMANCE OF EACH STEP JUDGEDAS SATISFACTORY OR UNSATISFACTORY BY BOARD OFEXPERT RATERS. ALL STEPS TO BE COMPLETED WITHIN2 HOURS



( ) 3.04 CENTER LINE MUST BE PROVIDED FOR ALL GEOMETRICCOMPONENTS

( ) 3.05 DIMENSIONS MUST BE ACCURATE TO ±1/64"( ) 3.06 DIMENSIONS MUST BE ACCURATE TO ± .005


VIEW( ) 3.02 ALL MATERIALS USED MUST BE LISTED

87

MISOE NO.



1.00 CONDITION

2.00 PERFORMANCE

TERMOB NO. 10-017

,GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME

3.00 EXTENT

GENERAL STATEMENT OF EXTENT ANb EXTENT OF RESULTING OUTCOME.

86

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION


UNIT 02 TOLERANCING

TERMOB NO. 1Qr018

( ) 1.01 DETAIL DRAWINGS OF HAND GRINDER WITHOUT DIMENSIONS


2.00 PERFORMANCE


( ) 2.01 DIMENSION DRAWINGS OF HAND GRINDER SPECIFYING TOLERANCEWHERE NEEDED ACCORDING TO THE FOLLOWING PROCEDURE;

( ) 2.02, DRAW TITLE BLOCK( ) 2.03 PLACE LOCATION DIMENSIONS ON GEOMETRIC COMPONENTS

( ) 2.04 DIMENSION RADII, ADDING TOLERANCES( ) 2.05 DIMENSION HOLE LOCATIONS, SPECIFYING TOLERANCES ON

LOCATION( ) 2.06 OBTAIN TOLERANCES FOR COMMERCIAL PARTS FROM CATALOG

( ) 2.07 LIST GENERAL TOLERANCES( ) 2.08 ADD OVERALL DIMENSIONS AND NOTES

3.00 EXTENT


( ) 3.01 DIMENSIONSUSE ANDCORRECT

AND TOLERANCES WILL BE APPROPRIATE TO THEMETHOD OF MANUFACTURE OF THE HAND GRINDER.DRAFTING PROCEDURE WILL BE FOLLOWED AND

THE PERFORMANCE OF EACH STEP WILL BE JUDGED ASSATISFACTORY OR UNSATISFACTORY BY BOARD OF EXPERT

RATERS. ALL STEPS TO BE COMPLETED WITHIN 8 HOURS.

( ) 3.02 ALL PERTINENT INFORMATION WILL BE SUPPLIED (TABLE T-3A)



( ) 3.05 USE TRUE POSITION DIMENSIONS TO DETERMINE HOLELOCATIONS

( ) 3.06 PARTS ADJACENT TO COMMERCIAL PARTS WILL BE TOLERANCEDPROPERLY TO SATISFACTION OF BOARD OF EXPERT RATERS

( ) 3.07 INCH MEASUREMENTS ACCURATE TO ± 1/64", DECIMALMEASUREMENTS ACCURATE TO ± .0005


VIEW

MISOE NO.


USOE CODE NO(S) UNIT 02 TOLERANCING

TERMOB NO. 10-018

1.00 CONDITION

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME:

3.00 EXTENT

GENARAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME

0

MI SON NO.


1.00 CONDITION

UNIT 02 TOLEBANCING

TERMOB NO. 10-019

( ) 1.01 DETAIL DRAWING OF FAN ASSEMBLY WITHOUT DIMENSIONS


2.00 PERFORMANCE


( ) 2.01 DIMENSION DRAWINGS OF FAN ASSEMBLY SPECIFYINGTOLERANCES. WHERE NEEDED

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 PLACE LOCATION DIMENSIONS ON GEOMETRIC COMPONENTS

( ) 2.04 DIMENSION RADII, ADDING TOLERANCES( ) 2.05 DIMENSION HOLE LOCATIONS, SPECIFYING TOLERANCES ON

LOCATION( ) 2.06 OBTAIN TOLERANCES,, FOR BALL BEARINGS FROM CATALOG

( ) 2.07 LIST GENERAL TOLERANCES( ) 2.08 ADD OVERALL DIMENSIONS AND NOTES

3.00 EXTENT


( ) 3.01 DIMENSIONS AND TOLERANCES WILL BE APPROPRIATE TO THEUSE AND METHOD OF MANUFACTURE OF THE FAN ASSEMBLY.CORRECT DRAFTING PROCEDURES WILL BE FOLLOWED ANDTHE PERFORMANCE OF EACH STEP WILL BE JUDGED ASSATISFACTORY OR UNSATISFACTORY BY BOARD OF EXPERT

RATERS. ALL STEPS TO BE COMPLETED WITHIN 4 HOURS.

( ) 3.02 ALL PERTINENT INFORMATION MUST BE LISTED (TABLET -3A)



( ) 3.05 USE TRUE POSITION DIMENSIONING TO DETERMINE HOLELOCATIONS

( ) 3.06 BEARINGS APPROPRIATE TO USE WILL BE SELECTED

( ) 3.07 INCH MEASUREMENTS ACCURATE TO i 1/64", DECIMALMEASUREMENTS TO ± .005

( ) 3.08 MAJORITY OF DIMENSIONS SHOULD BE SUPPLIED ON PRINCIPALVIEW 91

MISOE NO.


USOE CODE NO(S) UNIT 02 TOLERANCING

TERMOB NO. 10-019

1.00 CONDITION

2.00 PERFORMANCE


3.00 EXTENT


92

MISOE


1.00 CONDITION

UNIT 03 WELDING SYMBOLS

TERMOB NO. 10-020

( ) 1.01 LAYOUT SKETCH, DIMENSIONS AND SPECIFICATIONS FORWELDED LINK


2.00 PERFORMANCE


( ) 2.01 MAKE A TWO VIEW, DIMENSIONED DRAWING OF A WELDED LINKACCORDING TO THE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 PLACE SIZE DIMENSIONS ON EACH GEOMETRIC COMPONENT

( ) 2.04 ESTABLISH LOCATION DIMENSIONS, INCLUDING HOLE LOCATIONS

( ) 2.05 ADD WELDING SYMBOLS( ) 2.06 ADD OVERALL DIMENSIONS AND NOTES

3.00 EXTENT


( ) 3.01 DIMENSIONS AND WELDING SYMBOLS MUST BE CLEAR ENOUGH SOAS TO ALLOW PROPER MANUFACTURE OF PIECE. CORRECTDRAFTING PROCEDURE WILL BE FOLLOWED WITH THE PER-FORMANCE OF EACH STEP JUDGED AS SATISFACTORY dRUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALL STEPSTO BE COMPLETED WITHIN TWO HOURS.


( ) 3.03 DIMENSIONS WILL REQUIRE ACCURACY TO ± 1/64"

( ) 3.04 DIMENSIONS WILL REQUIRE ACCURACY TO ± .005

( ) 3.05 AMERICAN NATIONAL STANDARD SYMBOLS MUST BE USEDCORRECTLY


VIEW

93

PROGRAM DRAFTING

MISOE NO.


USOE CODE NO(S) UNIT 03 WELDING SYMBOLS

1.00 CONDITION

2.00 PERFORMANCE

TERMOB NO. 10-020


3.00 EXTENT


9

.

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION



TERMOB NO. 10-021

( ) 1.01 LAYOUT SKETCH DIMENSIONS AND SPECIFICATIONS FORWELDED BRACKET WITH CURBED SUPPORTS

( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES

2.00 PERFORMANCE


( ) 2.01 MAKE A THREE VIEW, DIMEMSIONED.DRAWING OF A WELDED

BRACKET ACCORDING TO THE FM14'0141NC' PROCEDURE :


( ) 2.04 ESTABLISH LOCATION DIMENSIONS INCLUDING HOLE LOCATIONS


3.00 EXTENT


) 3.01 DIMENSIONS AND WELDING SYMBOLS MUST BE CLEAR ENOUGHSO AS TO ALLOW PROPER MANUFACTURE OF PIECE. CORRECTDRAFTING PROCEDURE WILL BE FOLLOWED WITH THEPERFORMANCE OF EACH STEP JUDGED AS SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALL

STEPS TO BE COMPLETED WITHIN THREE HOURS.



( ) 3.04 DIMENSIONS WILL REQUIRE ACCURACY TO ± .005"

( ) 3.05 AMERICAN NATIONAL STANDARD SYMBOLS MUST BE USEDCORRECTLY


VIEW9 b

MISOE NO.


USOE CODE NO(S) UNIT 03 ;MDT% SYMBOLS

TERMOB NO. 10-021

1.00 CONDITION

2.00 PERFORMANCE


3.00 EXTENT


96'

MISOE NO.

9



TERMOB NO. 10-022

1.00 CONDITION

( ) 1.01 LAYOUT SKETCH, DIMENSIONS AND SPECIFICATIONS FORWELDED CASTER BRACKET


2.00 PERFORMANCE


( ) 2.01 MAKE A TWO VIEW, DIMENSIONED DRAWING OF A CASTERBRACKET ACCORDING TO THE FOLLOWING PROCEDURE:


( ) 2.04 ESTABLISH LOCATION DIMENSIONS, INCLUDING HOLE LOCATIONS


3.00 EXTENT


( ) 3.01 DIMENSIONS AND WELDING SYMbOLS MUST BE CLEAR ENOUGHSO AS TO ALLOW PROPER MANUFACTURE OF PIECE. CORRECTDRAFTING PROCEDURE WILL BE FOLLOWED WITH THEPERFORMANCE OF EACH STEP JUDGED AS SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN THREE HOURS.



( ) 3.04 DIMENSIONS WILL REQUIRE ACCURACY TO ± .005"

( ) 3.05 AMERICAN NATIONAL STANDARD SYMBOLS MUST BE USED

CORRECTLY( ) 3.06 MAJORITY OF DIMENSIONS SHOULD BE SUPPLIED ON PRINCIPAL

VIEW

9

PROGRAM DRAFTING

USOE CODE NO(S)-

1.00 CONDITION

2.00 PERFORMANCE

MISOE NO.


UNIT 03 WELDING- SYMBOLS

TERMOB NO. 10-022


3.00 EXTENTti


9

MISOE NO.

PROGRAM DRAFTItiG

1.00 CONDITION


UNIT 04 LINE CONVENTIONS

TERMOB NO. 10-023

( ) 1.01 SPECIFICATIONS FOR MILLING JACK WITH KNURLED COLLAR( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE


( ) 2.01 DETAIL MILLING JACK ACCORDING TO THE FOLLOWINGPROCEDURE:

( ) 2.02 DETERMINE NUMBER OF VIEWS( ) 2.03 MAKE ROUGH SKETCH OF DRAWING FOR POSITION OF VIEWS

( ) 2.04 DRAW TITLE BLOCK( ) 2.05 DRAW MAIN CENTER LINES STARTING WITH CHARACTERISTIC

VIEW( ) 2.06 CONSTRUCT OBJECT LINES( ) 2.07 ADD FILLETS, ROUNDS AND ARROWHEADS( ) 2.08 DARKEN ALL SIGNIFICANT LINES( ) 2.09 ADD DIMENSIONS AND NOTES

3.00 EXI'ENT


3.01 DRAWINGS WILL BE COMPLETE ENOUGH TO ALLOW MANUFACTUREOF PART. CORRECT DRAFTING PROCEDURE WILL BEFOLLOWED WITH THE PERFORMANCE OF EACH STEP JUDGEDAS SATISFACTORY OR UNSATISFACTORY BY BOARD OFEXPERT RATERS. ALL STEPS TO BE COMPLETED WITHINSIX HOURS.

) 3.02 DRAWING MUST HOW CHARACTERISTIC VIEW AND AS MANYADDITIONAL VIEWS AS NECESSARY TO SHOW ALLCHARACTERISTICS OF PART

( ) 3.03 LAYOUT OF DRAWING MUST ALLOW ADEQUATE ROOM Fob, NOTATIONS


( ) 3.05 WORE FROM CHARACTERISTIC OR MAIN VIEW TO OTHEP VIEWSDEVELOPING ALL SIMULTANEOUSLY

( ) 3.06 LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

( ) 3.07 DIMENSION LINES MUST BE ESTABLISHED BEFORE FILLETS AND--, ROUNDS OR ARROWHEADS ARE ADDED

( ) 3.08 LIES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

( 1 3.09 DIMENSIONS MUST BE AT LEAST 3/8" APART

PROGRAM DRAFTING

MISOE NO.


USOE CODE NO(S) UNIT 04 7114E76NMITTOTT

TERMOB NO. 10 -023

1.00 CONDITION

2.00 PERFORMANCE


3.00 EXTENT


1 0 o

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION

DIVISION 02

UNIT 04 LINE CONVENTIONS

TERMOB NO. 10-024

( ) 1.01 SPECIFICATIONS AND SKETCH OF HAND WHEEL( ) 1.02 BASIC DRAFTSMANPS SUPPLIES (TABLE T-3)

2.00 PERFORMANCE


( ) 2.01 MAKE TWO VIEW DRAWING OF HAND WHEEL TO INCLUDE FRONT(CIRCULAR) VIEW AND SIDE VIEW SHOWING PHANTOMSECTION.

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH'S-KETCH OF DRAWING FOR POSITION OF VIEWS

( ) 2.04 CONSTRUCT AND DARKEN OBJECT LINES( ) 2.05 FILL IN PHANTOM LINES .

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF, RESULTING OUTCOME

( ) 3.01 DRAWINGS MUST SHOW ALL CHARACT RISTICS OF THE PART TOSATISFACTION OF BOARD OF EXPERT RATERS. CQRRECTDRAFTING PROCEDURE MUST BE FOLLOWED WITH THECOMPLETION OF EACH STEP JUDO AS SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALL STEPSTO BE COMPLETED WITHIN TWO HOURS.


( ) 3.03 LAYOUT MUST ALLOW AMPLE ROOM FOR CLARITY OF DETAIL


( ) 3.05 PHANTOM LINES MUST BE CONSITENT IN LENGTH

101

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

MISOE NO.


UNIT 04 4LINE CONVENTIONS

TERMOB NO. 10-024


3.00 EXTENT


102

4.

MISOE NO.

PROGRAM DRAFTING DIVISION 03 SECTIONING_

1.00 CONDITION1.

UNIT 01 FULL

TERMOB NO. 10-025

( ) 1.01 SPECIFICATIONS ARE SKETCH OF "U" PULLEY( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE


( ) 2.01 MAKE TWO VIEW DRAWING OF PULLEY TO INCLUDE FRONT(CIRCULAR) VIEW AND SIDE VIEW IN SECTION ACCORDINGTO THE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF DRAWING FOR POSITIONING OF VIEWS

( ) 2.04 CONSTRUCT AND DARKEN OBJECT LINES( ) 2.05 FILL IN SECTION LINES

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESUHrING OUTCOME

( ) 3.01 DRAWINGS MUST SHOW ALL CHARACTERIST CS OF THE PART TO.SATISFACTION OF BOARD OF EXPERTRATERS. CORRECTDRAFTING PROCEDURE WILL BE FOLLOWED WITH THE COMPLE-TION OF EACH STEP JUDGED AS SATISFACTORY or.

UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALL STEPSTO BE COMPLETED WITHIN 1-1/2 HOURS


( ) 3.03 LAYOUT MUST ALLOW AMPLE ROOM FOR CLARITY OF DETAIL


( ) 3.05 SECTION LINES MUST BE OF EVEN WEIGHT AND EVENLYSPACED

103

PROGRAM DRAFTING .

MISOE NO.

DIVISION 03 SECTIONING

USOE CODE NO(S) UNIT 01 PME

TERMOB NO. 10425

1.00 CONDITION

2.00 PERFORMANCE

GENERAL STATEMENT OF PERF RMANCE AND RESULTING OUTCOME

3.00 EXTENT


MISUE NO.

PROGRAM DRAFTING

1.00 CONDITION

DIVISION 03 r--(1--1Ljainiics,

UNIT 01 FULL02 HALF

- TERMOB NO. 10-026

( ) 1.01 SPECIFICATIONS AND SKETCH OF CENTERING BEARING( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE


( ) 2.01 MAKE A TWO VIEW DRAWING OF THE CENTERING BEARIN(, TOINCLUDE FRONT (CIRCULAR) VIEW AND A SIDE VIEW INEITHER FULL OR HALF SECTION WHICHEVER IS DECIDEDMORE APPROPRIATE BY THE STUDENT. THESE DRAWINGSTO BE MADE ACCORDING TO THE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF DRAWING FOR POSITION OF VIEWS( ) 2.04 CONSTRUCT AND DARKEN OBJECT LINES( ) 2.05 gni, IN SECTION LINES

3.00 EXTENT

GJ


( ) 3.01 DRAWINGS MUST SHOW ALL CHARACTERISTICS OF THE PART TOTHE SATISFACTION OF BOARD OF EXPERT RATERS. STUDENT

) SHOULD HAVE SHOWN SIDE VIEW IN HALF SECTION.CORRECT DRAFTING PROCEDURE MUST BE FOLLOWED WITH THECOMPLETION OF EACH STEP JUDGED AS SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN 2-1/2 HOURS.

( ) 3.02 MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3A)( ) 3.03 LAYOUT MUST ALLOW AMPLE ROOM FOR CLARITY OF DETAIL( ) 3.04 LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT( ) 3.05 SECTION LINES MUST BE OF EVEN WEIGHT AND EVENLY SPACED

10)

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

DIVISION 03

MISOE NO.

SECTIONING

UNIT 01 FULL402 HALF

TERMOB NO. 10-026


3.00 EXTENT


1 CJti

MISOE NO.

PROGRAM )RAFT ING

1.00 CONDITION

DIVISION 03 SECTIonlic,

UNIT 02 HALF

TERMOB NO. 10-027

( ) 1.01 SPECIFICATIONS AND SKETCH OF CONE PULLEY

( ) 1.02 BASIC DRAFTSMAN'S StIPPLIES (TABLE T-3)

2.00 PERFORMANCE


( ) 2.01 MAKE TWO VIEW DRAWING OF CONE PULLEY TO INCLUDE FRONT(CIRCULAR) VIEW AND SIDE VIEW IN HALF SECTIONACCORDING TO THE FOLLOWING PROCEDURE:

2.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF DRAWING FOR POSITION OF VIEWS

( ) 2.04 CONSTRUCT AND DARKEN OBJECT LINES( ) 2.05 FILL IN SECTION LINES

3.00 EXTENT .

GEUERAL STATEMENT OF EXTENT AND EXTENT OF RESULTiNG OUTCOME

( ) 3.01 DRAWINGS MUST SHOW ALL CHARACTERISTICS OF THE PART 11.0

SATISFACTION OF BOARD OF EXPERT RATERS. CoRRWTDRAFTING PROCEDURE MUST BE FOLLOWED WITH TH.E'CoM-PLETIoN OF EACH STEP JUDGED AS SATISFAOWRS ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN 2 HOURS.


C ) 3.03 LAYOUT MUST ALLOW AMPLE ROOM FOR CLARITY OF DETAIL


( 1 3 .05 SECTION LINES MUST BE OF EVEN WEIGHT AND EVENLY SPACED

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

DIVISION

MISOE NO.

03 SECTIUtJIUG

UNIT 02 HALF

TERMOB NO. 10-021


3.00 EXTENT

4


0

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION

DIVISION 153" SECTIONING_

UNIT 03 REMOVED

TERMOB Nd. 10-028

( ) 1.01 SPECIFICATIONS AND TWO VIEW DRAWING OF HANDWHEEL


2.00 PERFORMANCE


( ) 2.01 DRAW REMOVED SECTIONS OF SPOKE AND RIM OF HANDWHEELACCORDING TO THE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK(-) 2.03 ROUGH IN REMOVED SECTIONS ON TWO VIEW DRAWING GIVEN

( ) 2.04 IDENTIFY 'REMOVED SECTIONS

( ) 2.05 ,DARKEN OBJECT LINES( ) 2.06 ADD SECTION LINES

3.00 EXTENT


( ) 3.01 REMOVED SECTIONS MUST ADEQUATELY SHOW CHARACTERISTICSOF PART TO SATISFACTION OF BOARD OF EXPERT RATERS.CORRECT DRAFTING PROCEDURE WILL BE FOLLOWED WITHTHE COMPLETION OF EACH STEP JUDGED AS SATISFACTORYOR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALL

STEPS TO BE COMPLETED WITHIN ONE HOUR.


( ) 3.03 THE SCALE OF THE REMOVED SECTION MUST ALLOW FORADEQUATE RENDERING OF DETAIL

( ) 3.04 CUTTING PLANE LINE WILL INDICATE POSITION OF REMOVEDSECTION ON DRAWING. ALL PARTS MUST BE LABELLED

( ) 3.05 ALL LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT'

( ) 3.06 SECTION LINES APPROPRIATE TO MATERIAL SPECIFIED MUSTBE USED IF MORE THAN ONE MATERIAL IS SPECIFIED. IF

ONLY ONE MATERIAL IS SPECIFIED, USE LINES APPROPRIATEFOR CAST IRON.

10

MISOE NO.

PROGRAM DgAFTING DIVISION 03 SECTIONING

USOE CODE NOES) UNIT 03 REMOVE

1.00 CONDITION

TERMOB NO. 10-028

2.00 PERFORMANCE


3.00 EXTENT


1 i 0

MISOE NO.

PROGRAM DRAFTING DIVISION 03 SECTIONING

1.00 CONDITION

UNIT 03 REMOVED

TERMOB NO. 10-029

( ) 1.01 SPECIFICATIONS AND TWO VIEW DRAWING OF A BLOCK AND

TACKLE HOOK( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE


( ) 2.01 DRAW TWO REMOVED SECTIONS OF HOOK ACCORDING TO THEFOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 ROUGH IN REMOVED SECTIONS ON TWO VIEW DRAWING GIVEN

( ) 2.04 IDENTIFY REMOVED SECTIONS) 2.05 DARKEN OBJECT LINES

( 2.06 ADD SECTION LINES

3.00 EXTENT


( ) 3.01 REMOVED SECTIONS MUST ADEQUATELY SHOW CHARACTERISTICSOF PART TO SATISFACTION OF BOARD OF EXPERT RATERS.CORRECT DRAFTING PROCEDURE WILL BE FOLLOWED WITHTHE COMPLETION OF EACH STEP JUDGED AS SATISFACTORYOR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALL

STEPS TO BE COMPLETED WITHIN ONE HOUR.


( ) 3.03 THE SCALE OF THE REMOVED SECTION MUST ALLOW FORADEQUATE RENDERING OF DETAIL

( ) 3.n4 CUTTING PLANE LINE WILL INDICATE POSITION OF REMOVEDSECTION ON DRAWING. ALL PARTS MUST BE LABELLED

( ) 3.05 ALL LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

( ) 3.06 SECTION LINES APPROPRIATE TO MATERIAL SPECIFIED MUSTBE USED IF MORE THAN ONE MATERIAL IS SPECIFIED. IF

ONLY ONE MATERIAL IS SPECIFIED, USE LINES APPROPRIATEFOR CAST IRON

111

PROGRAM DRAPTI I -

MISOE NO


USOE CODE NO(S) UNIT 03 REMOVED

TERMOB NO. i4m029

1,00 CONDITION

2.00 PERFORMANCE


3.00 EXTEN4

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTINGOUTCOME

112

MISOE NO


UNIT 04 OFFSET

TERMOB NO. 10-030

1.00 CONDITION

( ) 1.01 TWO VIEW DRAWING AND SPECIFICATIONS FOR CENTERINGBEARING WITH THREE MOUNTING HOLDS


2.00 PERFORMANCE


2.01 DRAW TWO REMOVED SECTIONS OF A CENTERING BEARINGACCORDING TO THE FOLLOWING PROCEDURE:

( )

2.02 DRAW TITLE BLOCK) 2.03 DETERMINE NUMBER OF VIEWS NECESSARY

) 2.04 ROUGH IN VIEWS INCLUDING SECTIONING

' 2.05 DARKEN OBJECT LINES) 2.06, ADD SECTION LINES

3.00 EXTENT


( ) 3.01 SECTION MUST ACCURATELY SHOW HOLES IN CIRCULAR VIEW.

CORRECT DRAFTING PROCEDURE MUST BE FOLLOWED WITHTHE COMPLETION OF EACH STEP JUDGED AS SATISFACTORYOR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALL

STEPS TO BE COMPLETED WITHIN TWO HOURS.


( ) 3.03 ALL ASPECTS OF PART MUST BE FULLY ILLUSTRATED TOSATISFACTION OF BOARD OF EXPERT RATERS

( ) 3.04 HOLE REPRESENTED IN OFFSET SECTION MUST BE REPRESENTED

IN SIDE VIEW( ) 3.05 LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT.

PROPER SECTION LINES FOR MATERIAL OF PART MUST BE EVEN

( ) 3.06 SECTION LINES APPROPRIATE TO MATERIAL SPECIFIED MUST

BE USED IF MORE THAN ONE MATERIAL IS SPECIFIED. IF

ONLY ONE MATERIAL IS SPECIFIED, LINES APPROPRIATEFOR CAST IRON SHOULD BE USED

113

PROGRAM .DRAFTING

USOE CODE NO(S)

1.00 CONDI*ON

MISOE NO.


UNIT 04 OFFSET

TERMOB NO. 1(11431

2.00 PERFORMANCE


3.00 EXTENT


114

MISOE NO.

PROGRAM DRAFT_ NG

1.00 cONDITION


UNIT 0-4 OFFSET

TERMOB NO. 10-031

( ) 1.01 TWO VIEW DRAWING OF BRASS PIPE FLANGE WITH THREEMOUNTING HOLES IN FLANGE


2.00 PERFORMANCE


( ) 2.01 DRAW FRONT VIEW ILLUSTRATING METHOD OF SHOWING HOLESIN SECTION USING CUTTING PLANE LINE THROUGH TWOHOLES ACCORDING TO THE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 ROUGH IN OFFSET SECTION ON VIEWS GIVEN

( ) 2.04 DARKEN OBJECT LINES( ) 2.05 ADD SECTION LINES

1.00 EXTENT


) 3.01 SECTION MUST ADEQUATELY SHOW HOLES. CORRECT DRAFTINGPROCEDURE MUST BE FOLLOWED WITH THE COMPLETION OFEACH STEP JUDGED AS SATISFACTORY OR UNSATISFACTORYBY BOARD OF EXPERT RATERS. ALL STEPS TO BE COM-PLETED WITHIN 1-1/2 HOURS.


( ) 3.03 HOLE REPRESENTED IN OFFSET SECTION MUST BE SHOWN INEND VIEW

( ) 3.04 LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT.PROPER SECTION LINES FOR BRASS MUST BE SHOWN

( ) 3.05 SECTION LINES APPROPRIATE TO THE MATERIAL SPECIFIEDMUST BE USED IF MORE THAN ONE MATERIAL IS SPECIFIED

115

PROGRAM DRAFTING

;USOE CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

MISOE NO.

DIVISION 03 SECTIbNING

UNIT 04 OFFSET

TERMOB NO. 10-031

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUT ME

3.00 EXTENT


116

MISOE NO.

PROGRAM , DRAFTING DIVISION 03 SECTIONING

UNIT 05 BROKEN OUT

TER0013 NO. 10-032

1.00 CONDITION

( ) 1.01 SPECIFICATIONS AND TWO 4.1EW DRAWING OF 2 INCH HORIZONTALLIFT CHECK VALVE WITH CUTTING PLANE


2.00 PERFORMANCE

GENI.PAIL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME

( ) 2.01 DRAW A BROKEN OUT SECTION OF VALVE BODY ACCORDING TOTHE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 ROUGH IN BROKEN OUT SECTION ON TWO VIEW DRAWING GIVEN

( ) 2.04 DARKEN OBJECT LINES( ) 2.05 ADD SECTION LINES,

3. 00 EXTENT


( ) 3.01 SECTION MUS" ADEQUATELY SHOW CONSTRUCTION OF VALVE

BODY. C) RECT DRAFTING PROCEDURE WILL BE FOLLOWED

WITH TH COMPLETION OF EACH JUDGED AS SATISFACTORYOR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS MUST BE COMPLETED WITHIN 2-1/2 HOURS.

) 3.02 ALL PERTINENT INFORMATION MUST BE LISTED (TABLE i° -3A)

C ) 3.03 BROKEN OUT SECTION MUST SHOW WORKINGS OF VALVE TOSATISFACTION OF BOARD OF EXPERT RATipS


( ) 3.05 SECTION LINES APPROPRIATE TO MATERIAL SPECIFIED MUSTBE USED IF MORE THAN ONE MATERIAL IS SPECIFIED.IF ONLY ONE MATERIAL IS SPECIFIED, LINES APPROPRIATEFOR CAST IRON SHOULD BE USED

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

MISOE NO.

DIVISION 0' SECTIONING

UNIT 05 BROKEN OUT

TERMOB NO. 10-032

2.00 PERFORMANCE


3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCAE

MISOE NO.


1.00 CONDITION

UNIT 05 BROKEN OUT

TERMOB NO. 10-033 ita./11=10.

( ) 1.01 SPECIFICATIONS AND TWO VIEW DRAWING OF 2 INCH GLOBEVALVE WITH CUTTING PLANE LINE


2.00 PERFORMANCE


( ) 2.01 DRAW A BROKEN OUT SECTION OF VALVE BODY ACCORDING TOTHE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 ROUGH IN BROKEN OUT SECTION ON TWO VIEW DRAWING GIVEN

( ) 2.04 DARKEN OBJECT LINES( ) 2.05 ADD SECTION LINES

3.00 EXTENT


( ) 3.01 DRAWING MUST SHOW ALL PERTINENT DETAILS OF VALVE.CORRECT DRAFTING PROCEDURE WILL BE FOLLOWEE WITHTHE COMPLETION OF EACH STEP JUDGED AS SATISFACTORYOR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN 2-1/2 HOURS.

( 3.02 ALL PERTINENT INFORMATION MUST BE LISTED (TABLE T-3A)

( ) 3.03 BROKEN OUT SECTION MUST SHOW WORKINGS OF VALVE TOSATISFACTION OF BOARD OF EXPERT RATERS


( ) 3.05 SECTION LINES APPROPRIATE TO MATERIAL SPECIFIED MUSTBt USED IF MORE THAN ONE MATERIAL IS SPECIFIED. IF

ONLY ONE MATERIAL IS SPECIFIED, LINES APPROPRIATEFOR CAST IRON SHOULD BE USED

iiJ

PROGRAM DRAFTING

'MISOE NO.

SECTIONING

USOE CODE NO(S) UNIT 05 BROKEN OU'

1.00 CONDITION

TERMOB NO. 10-033

2.110 PERFORMANCE


3.00 EXTENT


MISOE NO.


1.00 CONDITION

UNIT 06 REVOLVED

TERMOB NO. 10-O34

( ) 1.01 ISOMETRIC DRAWING OF CLAMP BRACKET ILLUtTRATING POINTOF SECTIONING

( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES. (TABLE T-3)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE A TWO VIEW WORKING DRAWING OF CLAMP BRACKET

AND ILLUSTRATE A REVOLVED SECTION ACCORDING TO THEFOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 CONSTRUCT FRONT AND TOP VIEW OF CLAMP BRACKET( ) 2.04 CONSTRUCT POSITION OF CUTTING PLANE IN TOP VIEW( ) 2.05 DRAW REVOLVED SECTION IN TOP VIEW( ) 2.06 DRAW TWO BREAK LINES ON BOTH SIDES OF REVOLVED SECTION( ) 2.07 DIMENSION AND DARKEN LINES TO COMPLETE DRAWING

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01 DRAWING MUST ACCURATELY DESCRIBE FORM AND SIZE FOR

THE MANUFACTURE OF CLAMP BRACKET. CORRECT DRAFTINGSTANDARDS TO BE FOLLOWED AND EACH STEP JUDGED ASSATISFACTORY OR UNSATISFACTORY BY BOARD OF EXPERTRATERS. ALL STEPS TO BE COMPLETED WITHIN THREEHOURS.

( ) 3.02 MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3A)( ) 3.03 LAYOUT TO BE CORRECTLY DISTRIBUTED ON PAPER( ) 3.04 POSITION OF CUTTING PLANE LINE DETERMINED FROM

ISOMETRIC DRAWING( ) 3.05 STANDARDS FOR REVOLVED SECTIONS TO BE FOLLOWED( ) 3.06 ADEQUATE SPACE TO BE ALLOWED FOR REVOLVED SECTION( ) 3.07 DIMENSIONS lo BE ACCURATELY TRANSFERRED FROM ISOMETRIC

DRAWING AND ALL LINES TO BE SHARP, DARE, _AND OFPROPER WEIGHT 121

I MISOE NO.


USOE CODE NO(S) UNIT 06 REVOLVED

1.00 CONDITION

2.00 PERFORMANCE

TERMOB NO. 10-Q34


3.00 EXTENT


r) 2

MISOE NO.


1.00 CONDITION

UNIT 07 ARCHITECTURAL

TERMOB NO. 10-035

( ) 1.01 PICTORIAL DRAWING OF A BOX CORNICE( ) 1.02- BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE A DETAIL SECTION DRAWING OF A BOX CORNICE

ACCORDING TO THE FOLLOWING PROCEDURES:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 DRAW WALL AND INDICATE PLATE( 2.04 DRAW ROOF SLOPE (PITCH TRIANGLE)( ) 2.05 PLACE IN RAFTER AND INDICATE CORNICE PROJECTION( ) 2.06 DRAW ROOF BOARDS AND PLACE IN FINISH MATERIALS( ) 2.07 DRAW GUTTER AND ROOF SHINGLES( ) 2.08 DARKEN ALL DETAIL LINES AND COMPLETE DRAWING

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01 DRAWING MUST ADEQUATELY SHOW CONSTRUCTION OF BOX

CORNICE. CORRECT DRAFTING PROCEDURES TO BE FOLLOWEDAND EACH STEP WILL BE JUDGED AS SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN 3 HOURS.

( ) 3.02( ) 3.03( ) 3.04( ) 3.05( ) 3.06( ) 3.07( ) 3.08

MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3A)SECTION LINES PLACED WHERE NEED b0CORRECT RISE AND SLOPE TO BE CALCULATEDDETERMINED BY ROOF SLOPEFINISH MATERIAL DETERMINED BY STYLE OF HOUSECONSIDERATION TO BE TAKEN FOR FLASHINGSUPPLY ALL DETAILS AND NOTATIONS

123

MISOE NO.


USOE CODE NO(S) UNIT- 07 ARCHITECTURAL

1.00 CONDITION

TERMOB 10-035

2,40---RERFORMANCE__

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCuN1

3.00 EXTENT


124

MISOE NO.

PROGRAM_ DRAFTING

1.00 CONDITION

DIVISION 04 DEVELOPML14 _UNIT 01 CURVED SURFACES

TERMOB NO. 10-036

( ) 1.01 TWO VIEW DRAWING OF RIGHT CIRCULAR CYLINDER


2.00 PERFORMANCE


( ) 2.01 MAKE DEVELOPMENT FROM A TWO VIEW DRAWING OF OBLIQUECYLINDER ACCORDING TO THE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 ESTABLISH STRETCH OUT LINE( ) 2.04 DIVIDE CIRCUMFERENCE OF CYLINDER INTO EQUAL PARTS

( ) 2.05 TRANSPOSE THESE INCREMENTS TO UNROLLED VIEW( ) 2.06 MEASURE LINES FROM STRETCH OUT (BASE) TO TOP LINE

( ) 2.07 CONNECT ENDS OF LINES TO REPRESENT INCLINE OF TOPAND BOTTOM

3.00 EXTENT.

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING wiTCOME

) 3.01 DEVELOPMENT MUST PROVIDE SUFFICIENT INFORMATION SO

AS TO ALLOW MANUFACTURE OF PIECE. LINES OFDRAWING WILL BE SHARP, CLEAR, DARK AND OF EVENWEIGHT. WORK WILL BE FREE OF EXTRANEOUS MARKS.CORRECT DRAFTING PROCEDURE WILL BE FOLLOWED WITHTHE COMPLETION OF EACH STEP JUDGED AS SATISFACTORYOR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN 2 HOURS.

( ) 3.02( ) 3.03( ) 3.04( ) 3.05( ) 3.06

) 3.07

ALL PERTINENT INFORMATION MUST BE LISTED (TABLE T-3A)MEASUREMENTS MUST BE TAKEN FROM TWO VIEW DRAWING12-24 SECTIONS MUST BE USEDALL SECTIONS MUST BE OF EQUAL WIDTHLENGTHS MUST BE ACCURATE TO ± 1/64"CURVE WHICH RESULTS MUST ACCURATELY REPRESENT TOP OF

CYLINDER125

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

_2.00 PERFORMANCE

MISOE NO.

DIVISION 04 DEVELOPMENT

UNIT 01 CURVED SURFACES

TERMOB NO. 10-036


3.00 EXTENT

GENERAL STATEMENT OF EXTENT wirsAlbat. EXTENt OF RESULTING OUTCOME

1.26

MISOE NO.

to

PROGRAM DRAFTING DIVISION 04 DEVELOPMENTS

1.00 CONDITION


TERMOB NO. 10-037

( ) 1.01. TWO VIEW DRAWING OF OBLIQUE CYLINDER( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

i GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE DEVELOPMENT OF OBLIQUE CYLINDER ACCORDING TO

THE FOLLOWING PROCEDURE:

( ) .0 DRAW TITLE BLOCK( ) 2.03 ESTABLISH STRETCH OUT LINE( ) 2.04 DIVIDE CIRCUMFERENCE OF CYLINDER INTO EQUAL PARTS( ) 2.05 TRANSPOSE THESE INCREMENTS TO UNROLLED VIEW( ) 2.06 MEASURE LINES FROM STRETCH OUT LINE TO TOP AND

BOTTOM LINES( ) 2.07 CONNECT ENDS OF LINES TO REPRESENT INCLINE OF TOP AND

BOTTOM

3.00 EXTENT

GENERAL STATEMENT OF EXTENT' AND EXTENT OF RESULTING OUTCOME( S 3.01 DEVELOPMENT MUST PROVIDE SUFFICIENT INFORMATION SO AS

TO ALLOW MANUFACTURE OF PIECE. LINES OF DRAWING WILLBE SHARP, CLEAR, DARK AND OF EVEN WEIGHT. WORK WILLBE FREE OF EXTRANEOUS MARKS. CORRECT DRAFTING PROCEDURE WILL BE FOLLOWED WITH THE COMPLETION OF EACHSTEP JUDGED AS SATISFACTORY OR UNSATISFACTORY BYBOARD OF EXPERT RATERS. ALL STEPS TO BE COMPLETEDWITHIN 2 HOURS.

( ) 3.02( ) 3.03( ) 3.04( ) 3.05( ) 3.06( ) 3.07

MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3ATMEASUREMENTS MUST BE TAKEN FROM TWO VIEW DRAWING12-24 SECTIONS MUST BE ESTABLISHEDALL SECTIONS MUST BE OF EQUAL WIDTHLENGTHS MUST BE ACCURATE TO t 1/64"CURVE WHICH RESULTS MUST ACCURATELY REPRESENT TOP.AND BOTTOM IN TWO VIEW DRAWING

i2

MISOE NO.

PROGRAM. DRAFTING DIVISION 04 DEVELOPMENTS

USOE CODE NO(S)

1.00 CONDITION


TERMOB NO. 10-037

2.00 PERFORMANCE


3.00 EXTENT


123

MISOE NO.

_PROGRAM DRAFTING

1.,00 CONDITION

DIVISION 04 DEVELOPMENTS


TERMOB NO. 10-038

, ( ) 1.01 TWO VIEW DRAWING OF RIGHT CONE( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE DEVELOPMENT OF RIGHT CONE ACCORDING TO THE


( ) 2.02 -DRAW TITLE BLOCK( ) 2.03 DETERMINE NUMBER OF VIEWS( ) 2.04 ESTABLISH RADIUS OF 'DEVELOPMENT( ) 2.05 DETERMINE CENTER ANGLE TO ESTABLISH LENGTH OF

PERIMETER IN DEVELOPMENT

3.00 EXTENT


) 3.01 DEVELOPMENT MUST PROVIDE SUFFICIENT INFORMATION SO ASTO ALLOW MANUFACTURE OF PIECE. LINES OF DRAWINGWILL BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT.WORK WILL BE FREE OF EXTRANEOUS MARKS. CORRECTDRAFTING PROCEDURE WILL BE FOLLOWED WITH COMPLETIONOF EACH STEP JUDGED AS SATISFACTORY OR UNSATIS-FACTt= BY BOARD OF EXPERT RATERS, ALL STEPS TO BECOMPLETED WITHIN TWO HOURS.


( ) 3.03 LAYOUT MUST HAVE VIEWS EVENLY DISTRIBUTED ON PAGE SOAS TO ALLOW ROOM FOR NOTES

( ) 3.04 RADI= Z.:QUAL TO SLANT HEIGHT( ) 3.05 CENTER ANGLE DETERMINED BY THE RADIUS OF THE BASE

DIVIDED BY THE SLANT HEIGHT TIMES 3600

PROGRAM DRAFTING

MISOE NO.


USOE CODE NO(S) UNIT 01 CURVED SURFACES

TERMOB NO. M-038

1.00 CONDITION

2.00 PERFORMANCE


3.00 EXTENT


13o

ML SUE NO.

PROCRAM DRAFTINC

1.00 CONnTTION


UNIT 02 COMBINATIONS

TERMOB NO. 10-039

( ) 1.01 TWO VIEW DRAWING OF TWO-PIECE ELBOW

( ) L02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMAN0E


( )2.0flinxt DEVELOPMENT OF TWO-PIECE ELBOW ACCORDING TO THE


( ) 2.02 DRAW TITLE BLOCK( ) 2.03 ESTABLISH STRETCH OUT LINE FOR EACH PIECE

( ) 2.04 DIVIDE CIRCUMFERENCE OF EACH CYLINDER INTO EQUAL PARTS c

( ) 2.05 TRANSPOSE THESE INCREMENTS TO UNROLLED VIEW

( ) 2.06 MEASURE LINES FROM STRETCH OUT (BASE) LINES TOINCLINED EDGES

( ) 2.07 CONNECT ENDS OF LINES TO REPRESENT INCLINE OF JOINING

EDGES

3.06 EXTENT

GENERAL STATEMENT OF EXTENT. AND EXTENT OF RESULTING OUTCOME

( ) 3.01

( ) 3.02( ) 3.03( ) 3.04( ) 3.05( ) 3.06.

( ) 3.07

DEVELOPMENT MUST PROVIDE SUFFICIENT INFORMATION SO AS

TO ALLOW MANUFACTURE OF PIECE. LINES MUST BESHARP, CLEAR, DARK AND OR EVEN WEIGHT. WORK WILLBE FREE OF EXTRANEOUS MARKS. CORRECT DRAFTINGPROCEDURE WILL BE FOLLOWED WITH THE COMPLETION OFEACH STEP JUDGED AS SATISFACTORY OR UNSATISFACTORYBY BOARD OF EXPERT RATERS. ALL STEPS TO BE COMPLETEDWITH TWO HOURS.

ALL PERTINENT INFORMATION MUST BE LISTED (TABLE T-3A)MEASUREMENT WILL BE TAKEN FROM TWO VIEW DRAWING12-24 SECTIONS MUST BE ESTABLISHEDALL SECTIONS MUST BE OF EQUAL WIDTHLENGTHS MUST BE ACCURATE TO ± 1/64"CURVES WHICH RESULT MUST ACCURATELY REPRESENT JOINING

EDGES OF PIECES

131

MISOE NO.

PROGRAMv

DRAFTING DIVISION 04 DEVELOPMENTS...USOE CODE NO(S) UNIT 02 COMBINATIONS

1.00 CONDITION

2.00 PERFORMANCE

TERMOB NO. 10-039


3.00 EXTENT


.1111011111,

L

MISOE-NO.

__PROGRAM DRAFTING

1.00 CONDITION


UNIT 02 COMBINATIONS

TERMOB NO. 10-040

( ) 1.01 TWO VIEW DRAWING OF TRUNCATED CONE( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2,,00 PERFORMANCE


( ) 2.01 MAKE DEVELOPMENT OP A TRUNCATED CONE ACCORDING TOTHE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF LAYOUT FOR POSITION ON PAGE 4

( ) 2.04 ESTABLISH STRETCH OUT LINE( ) 2.05 DIVIDE INTO EQUAL INCREMENTS WITH THE USE OF RADII

( ) 2.06 MEASURE LENGTHS OF RADII FROM BASE TO FRUSTUM TOREPRESENT TRUNCATED PORTION

( ) 2.07 JOIN POINTS TO OBTAIN SMOOTH CURVE

3.00 EXTENT

GENLPAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME

C) 3.01 DEVELOPMENT MUST PROVIDE- SUFFICIENT.INFORMATIoN SO ASTO ALLOW MANUFACTURE OF PIECE. LINES OF DRAWINGWILL BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT.WORK WILL BE FREE OF EXTRANEOUS MARKS. CORRECTDRAFTING PROCEDURE WILL BE FOLLOWED WITH THE COM-PLETION OF EACH STEP JUDGED AS SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN TWO HOURS.


( ) 3.03 LAYOUT MUST HAVE VIEWS EVENLY DISTRIBUTED ON PAGE SOAS TO ALLOW ROOM FOR NOTATIONS

( ) 3.04 MEASUREMENTS MUST BE TAKEN FROM TWO VIEW DRAWING

( ) 3.05 12-24 SECTIONS MUST BE ESTABLISHED( ) 3.06 LENGTHS MUST BE ACCURATE TO ± 1/64"( ) 3.07 CURVE MUST ACCURATELY REPRESENT FRUSTUM

MISOE NO.


USOE CODE NO(S) UNIT 02 cumnINATTONR-.

TERMOB NO. 10-040

1.00 CONDITION

2-.-011 PERFORMANCE


3.00 EXTENT


134

MISOE NO.


UNIT 03 mlialkaLlusaaL__

TERMOB NO. 10-041

1.00 CONDITION

( ) 1.01 TWO VIEW DRAWING OF TRANSITION PIECE CONNECTING ACIRCULAR. AND A SQUARE PIPE

( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES 'TABLE T-3)

2.00 PERFORMANCE


( ) 2.01 MAKE DEVELOPMENT OF TRANSITION PIECE CONNECTING Acalicalia&ZIELLCata=41=6AnORDING To THE FOLLOWING

PRuCEDURE:

(,) 2.02 DRAW TITLE BLOCK( ) 203 MAKE ROUGH SKETCH OF LAYOUT FOR POSITIONING

( ) 2.04 CONSTRUCT TRIANGLE WHICH REPRESENTS FIRST, FLAT SURFACE'

( ) 2.05 DEVELOP ADJACENT, CONICAL SURFACE BY TRIANGULATIONMETHOD

( ) 2.06 CONSTRUCT ALL REMAINING SURFACES SIMILARLY

3.00 EXTENT

le


3.01 DEVELOPMENT MUST ALLOW ACCURATE MANUFACTURE OF PIECE.LINES OF DRAWING WILL BE SHARP, CLEAR, DARK AND OF

EVEN WEIGHT. WORK WILL BE FREE OF EXTRANEOUSMARKS. CORRECT DRAFTING PROCEDURE WILL BE FOLLOWED

WITH THE COMPLETION OF EACH STEP JUDGED AS SATIS-FACTORY OR UNSATISFACTORY BY BOARD OF EXPERT RATERS.ALL STEPS TO BE COMPLETED WITHIN TWO HOURS.


( ) 3.03 LAYOUT MUSTJ1AVE VIEWS EVENLY DISTRIBUTED SO AS TOALLOW ROOM FOR NOTATIONS

( ) 3.04 USE MEASUREMENTS FROM TWO VIEW DIAGRAM

( ) 3.05 TRIANGLES ARE FORMED USING THE SLANT HEIGHT AND THECHORD OF THE ARC FORMED BY THE DIVISION OF THECIRCUMFERENCE OF THE TOP

( ) 3.06 DEVELOP REMAINING SURFACES IN CLOCKWISE DIRECTION

( )

135

PROGRAM DRAFTING

USOE CODE NO(S)

DIVISION 04

MISOE NO.

DEVELOPMENTS

UNIT 03 TRANSITION PIECES

TERMOB NO. 10-041

1.00 CONDCTION

2--0-0--PERFORMANCE

GENERAL STAMMENT OF PERFORMANCE AND RESULTING OUTCOME

3.00 EXTENT


foirSOE NO.

pOOGPAM DRAFTING

1.00 CONDITION


UNIT 03' TRANSITION PIECES

TERMOB NO. ,10-642

( ) 1.01 TWO VIEW DRAWING OF TRANSITION PIECE CONNECTING TWO

PIPES( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE


( ) 2.01 MAKE DEVELOPMENT OF TRANSITION PIECE CONNECTING TWOPIPES ACCORDING TO THE FOLLOWING PROCEDURE:


( ) 2.04 TRIANGULATE SURFACE( ) 2.05 LAY OUT TRIANGLES IN TRUE SIZE AND REGULAR ORDER

( ) 2.06 CONNECT ENDS OF LINES TO DEVELOP CURVES OF TOP AND

BOTTOM

3.00 EXTENT


( ) 3.01 DEVELOPMENT MUST PROVIDE ENOUGH INFORMATION TO ALLOWMANUFACTURE OF PIECE. LINES WILL BE SHARP, CLEAR,DARK AND OF EVEN WEIGHT. WORK WILL BE FREE OF

EXTRANEOUS MARKS. CORRECT DRAFTING PROCEDURE WILL

BE FOLLOWED WITH THE COMPLETION OF EACH STEP JUDGED

AS SATISFACTORY OR UNSATISFACTORY BY BOARD OFEXPERT RATERS. ALL STEPS TO BE COMPLETED WITHIN

3-1/2 HOURS.


( ) 3.03 LAYOUT MUST HAVE VIEWS EVENLY DISTRIBUTED SO AS TO

ALLOW ROOM FOR NOTATIONS( ) 3.04 TRIANGLES ARE FORMED USING THE SLANT HEIGHT AND THE

CHORD OF THE ARC FORMED BY THE DIVISION OF THECIRCUMFERENCE OF THE BASE

( ) 3.05 MEASUREMENTS MUST BE TAKEN PROM TWO VIEW DRAWING

( ) 3.06 CURVE MUST ACCURATELY REPRESENT TOP AND BOTTOM OF

PIECE

PROGRAM DRAFTING

MISOE NO.


USOE CODE NOM UNIT 03 TRANSITION PIECES

TERMOB NO. 10-042 _

1.00 CONDITION

2A0 PERFORMANCE


3.00 EXTENT


MISOE NO.

PROGRAM DRAFTING DIVISION 05 AUXILIARY VIEWS

1.00 CONDITION

UNIT 01 PRIMARY

TERMOB NO. 10-043

( ) 1.01 TWO VIEW DRAWING AND SPECIFICATIONS OF DOVETAIL BRACKET


2.00 PERFORMANCE


) 2.01 DRAW AUXILIARY VIEW OF DOVETAIL BRACKET ACCORDING TOTHE FOLLOWING PROCEDURE:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 DRAW PRINCIPAL VIEWS( ) 2.04 DRAW REFERENCE LINES AND PROJECTORS( ) 2.05 TRANSFER DISTANCES( ) 2.06 COMPLETE VIEW, DARKEN LINES

3.00 EXTENT


( ) 3.01 AUXILIARY VIEW MUST DEFINE CHARACTERISTICS OF PART TOSATISFACTION OF BOARD OF EXPERT RATERS. CORRECTDRAFTING PROCEDURE MUST BE FOLLOWED WITH THE COM-PLETION OF EACH STEP JUDGED AS SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN TWO HOURS.


( ) 3.03 THESE TAKEN FROM VIEWS GIVEN( ) 3.04 AUXILIARY VIEWS MUST BE PROJECTED FROM THE VIEW WHICH

SHOWS THE SLANTING SURFACE AS AN EDGE

( ) 3.05 DISTANCES ARE TRANSFERRED FROM PRINCIPAL VIEWS( ) 3.06 LINES MUST BE SHARP, CLEAR; DARK AND OF EVEN WEIGHT

139

MISOE NO.

PROGRAM DRAFTING DIVISION 05 AUXILIARY VIEWS,

USOE CODE NO(S) UNIT 01 PRIMARY

1.00 CONDITION

11

TERMOB NO. 10-043

2.00 PERFORMANCE


3.00 EXTENT


.1.4u

MISOE NO.


1.00 CONDITION

UNIT 01 PAIRARY

TERMOB NO. 107044

( ) 1.01 TWO VIEW DRAWING AND SPECIFICATIONS OF FENDER BRACKET


2.00 PERFORMANCE


( ) 2.01 DRAW AUXILIARY VIEW OF FENDER BRACKET ACCORDING TOTHE FOLLOWING PROCEDURE:

) 2.02 DRAW TITLE BLOCK( ) 2.03 DRAW PRINCIPAL VIEWS

) 2.04 DRAW REFERENCE LINES AND PROJECTORS) 2.05 TRANSFER DISTANCES

( ) 2.06 COMPLETE VIEW, DARKENJANES

3.00 EXTENT


( ) 3.01 AUXILIARY VIEW MUST ACCURATELY DEFINE CHARACTERISTICSOF PART TO SATISFACTION OF BOARD OF EXPERT RATERS.CORRECT DRAFTING PROCEDURE MUST BE FOLLOWED WITHTHE COMPLETION OF EACH STEP JUDGED SATISFACTORY ORUNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN 2-a2/2 HOURS.

( ) 3.02 ALL PERTINENT INFORMATION MUST BE LISTED (TABLE T-.3A)

( ) 3.03, THESE TAKEN FROM VIEWS GIVEN( ) 3.04 AUXILIARY VIEWS MUST BE PROJECTED FROM THE VIEW WHICH

SHOWS THE SLANTING SURFACE AS AN EDGE

( ) 3.05 DISTANCES ARE TRANSFERRED FROM. PRINCIPAL VIEWS

( )3.06, LINES MOST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

4

141

pRoGgm DRAFTING

MISOE NO.

DIVISION 05o AUXILIARY VIEWS

USOE CODE NO(S) UNIT 01 PRIMARY

TERMOB NO 10.444

1.00 CONDITION

2.00 PERFORMANCE


3.00 EXTENT


142

Ire

MISOE NO.

PROGRAM DRAFTING0.,

1.00 CONDITION

DIVISION 05, AUXILIARY VIEWS

UNIT 02 SECONDARY

TERMOB NO. 10 045

( ) 1.01 TWO VIEW DRAWING AND SPECIFICATION OF CROSS ANCHOR( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME) 2.6i CONSTRUCT A SECONDARY AUXILIARY VIEW OF *M. CROSS

ANCHOR ACCORDING TO THE FOLLOWING PROCEDURE:

DRAW TITLE BLOCK( ) 2.03 LAYOUT DRAWING ESTABLISHING PRINCIPAL VIEWS( ) 2.04 DRAW PRIMARY AUXILIARY VIEW( ) 2.05 PROJECT SHORTENED VIEW OF CURVED SURFACE( ) 2.0G PROJECT POINTS ON CURVE TO FRONT VIEW-( ) 2.07 FINISH DRAWING

3.00 EXTENT

GENERAL STATEMENT OF EXTENT-AND EXTENT OF RESULTING OUTCOME( ) 3.01 DRAWING MUST DESCRIBE CHARACTERISTICS OF PART TO BOARD

OF EXPERT RATERS. CORRECT DRAFTING PROCEDURE WILL BEFOLLOWED WITH THE COMPLETION OF EACH STEP JUDGED ASSATISFACTORY OR UNSATISFACTORY BY BOARD OF EXPERTRATERS. ALL STEPS TO BE COMPLETED WITHIN 6 HOURS.

( ) 3.02 ALL PERTINENT INFORMATION MUST BE LISTED (TABLE T-3A)( ) 3.03 LAYOUT OF DRAWING MUST ALLOW AMPLE ROOM FOR PLACEMENT

OF ALL DETAILS( ) 3.04 AUXILIARY VIEW MUST BE PROJECTED FROM THE VIEW WHICH

SHOWS TU2 SLANTING SURFACE AS AN EDGE( ) 3.05 PROJECT THROUGH THE PRIMARY AUXILIARY VIEW( ) 3.06 MEASUREMENTS ARE TAKEN FROM THE PRIMARY AUILIARY VIEW( ) 3.07 ALL LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

.143

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

MISOE NO.

DIVISION 05 AUXILIARY VIEWS

UNIT 02 SECOUDABY

TERMOS NO. 1,0-045


3.00 EXTENT


144

MISOE NO.


I 1. 11 NO 11 1 NI IN

UNIT 02 SECONDARY

TERMOB NO. 10-046

1.00 CONDITION

( ) 1.01 TWO VIEWS AND SPECIFICATIONS OF 45° ELBOW( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3),

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 CONSTRUCT A SECONDARY AUXILIARY VIEW OF THE 45`' ELBOW


( ) 2.02 DRAW TITLE BLOCK( ) 2.03 LAYOUT DRAWING ESTABLISHING PRINCIPAL VIEWS( ) 2.04 DRAW PRIMARY AUXILIARY VIEW( ) 2.05 'PROJECT PRESHORTENED VIEW OF CURVED SURFACE( ) 2.06 PROJECT POINTS ON CURVE TO FRONT VIEW( ) 2.07 FINISH DRAWING

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING( ) 3.01 DRAWING MUST DESCRIBE CHARACTERISTICS OF

SATISFACTION OF BOARD OF EXPERT RATERS.'DRAFTING PROCEDURE WILL BE FOLLOWED WITHTION OF EACH STEP JUDGED AS SATISFACTORYSATISFACTORY BY BOARD OF EXPERT RATERS.BE COMPLETED WITHIN 4 HOURS

OUTCOMEPART TOCORRECTTHE COMPLE-OR UN-ALL STEPS TO

( ) 3.'02 ALL PERTINENT INFORMATION MUST BE LISTED (TABLE T-3A)( ) 3.03 LAYOUT OF DRAWING MUST ALLOW AMPLE ROOM FOR PLACEMENT

OF ALL DETAILS( ) 3.04 AUXILIARY VIN MUST BE PROJECTED FROM VIEW WHICH SHOWS

SLANTING SURFACE AS AN EDGE( ) 3.05 PROJECT THROUGH THE PRIMARY AUXILIARY VIEW 44

( )- 3.06 MEASUREMENTS ARE TAKEN FROM THE PRIMARY AUXILIARY VIEW( ) 3.07 ALL LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

145

MISOE NO.


USOE CODE NO(S) UNIT 02 SECONDARY

1.00 CONDITION

2.00 -PERFORMANCE

TERMOB NO. 10-046

4


3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT-OF RESULTING OUTCOME

14 6

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION

16.dDIVISION 06 WORKING DRAWiNQS

UNIT 01 DETAIL DRAWINGS

TERMOB NO. 10-047

( ) 1.01 DESIGN LAYOUT OF SPINDLE SHAFT( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3A)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 1.61 MAKE DETAIL DRAWING OF SPINDLE SHAFT ACCORDING TO THE


( ) 2.02 DRAW TITLE BLOCK( ) 2.03 DETERMINE NUMBER OF VIEWS( ) 2.04' MAKE ROUGH SKETCH OF DRAWING FOR POSITIONING OF VIEWS

( ) 2.05 DRAW MAIN CENTER LINES STARTING WITH CHARACTERISTICVIEWS

) 2.06 CONSTRUCT OBJECT LINES( ) 2.07 ADD FILLETS, ROUNDS AND ARROWHEADS( ) 2.08 ADD DIMENSIONS AND NOTES( ) 2.09' DARKEN ALL SIGNIFICANT LINES

3.00 EXTENT

GENERAL STATEMENT, OF EXTENT AND EXTENT OF RESULTING. OUTCOME( ) 3,01 DAAWINd WILL BE COMbLETZINOUGH TO ALLOW MANUFACTURE

OF PART. CORRECT DRAFTING PROCEDURE WILL BIB FOLLOWEDWITH THE PERFORMANCE OF EACH STEP JUDGED AS SATISFAC-TORY OR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO Be COMPLETED WITHIN 3 HOURS


( ) 3.03 DRAWING MUST SHOW- CHARACTERISTIC VIEW AND AS MANYADDITIONAL VIEWS AS NECESSARY TO SHOW ALL CHARAC-TERISTICS OF PART

( ) 3.04 LAYOUT OF DRAWING MUST ALLOW ADEQUATE ROOM FOR NOTATIONS( ) 3.05 WORK FROM CHARACTERISTIC MAIN VIEW TO OTHER. VIEWS

DEVELOPING ALL SIMULTANEOUSLY( ) 3.06 LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT(-) 3.07 DIMENSION LINES MUST BE ESTABLISHED BEFORE FILLETS,

ROUNDS OR ARROWHEADS( ) 3.08 DIMENSIONS MUST BE AT LEAST 3/8" APART( ) 3.09 LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

MISOE NO.

PROGRAM DRAFTING DIVISION 06 WORKING DRAWINGS

USG! CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

UNIT 01 DETAIL DRAWIN $

TERMOB NO. 10-047


EXTENT


MISOE

PROGRAM DRAFTING

1.00 CONDITION

DIVISION 06 WORKING DRAWINGS


TERMOB NO. 10-048

( ) 1.01_ DESIGN LAYOUT OF BLOCK AND CLAMP( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.0) PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE DETAIL DRAWING OF U BLOCK AND CLAMP ACCORDING TO


( ) 2.02 DRAW TITLE BLOCKC. ) 2.03 DETERMINE NUMBER OF VIEWS( ) 2.04 MAKE ROUGH SKETCH OF DRAWING FOR POSITIONING OF VIEWS

C ) 2.05 DRAW MAIN CENTER LINES STARTING WITH CHARACTERISTICVIEW

( ) 2.06 CONSTRUCT OBJECT LINES( ) 2.07 ADD FILLETS, ROUND AND ARROWHEADS( ) 2.08 ADD DIMENSIONS AND NOTES( ) 2.09 DARKEN ALL SIGNIFICANT LINES

3.00 EXTENT

GENERAL STATEMENT, OF EXTENT AND EXTENT OF RESULTING OUTCOME

( ) 3.01 DRAWING MUST BE CON&LETE ENOUGH TO ALLOW MANUFACTUREOF PART. CORRECT DRAFTING PROCEDURE MUST BE FOLLOWEDWITH THE COMPLETION OF EACH STEP TO BE JUDGED ASSATISFACTORY OR UNSATISFACTORT'BY BOARD OF EXPERTRATERS. ALL STEPS TO BE COMPLETED WITHIN 4 HOURS.

1 ) 3.02 ALL PERTINENT INFORMATION MUST BE LISTED (TABLE T-3A1

( ) 3.03 DRAWING MUST SHOW CHARACTERISTICS VIEW AND AS MANYADDITIONAL VIEWS AS NECESSARY TO SHOW ALL CHARACTERIS-TICS OF PART

( ) 3.04 LAYOUT OF DRAWING MUST ALLOW ADEQUATE ROOM FOR NOTATIONS

( ) 3.05 WORK FROM CHARACTERISTIC (MAIN)VIEW TO OTHER VIEWSDEVELOPING ALL SIMULTANEOUSLY

( ) 3.06 LINES MUST BE SHARP, CLEAR, DARR AND OF EVEN WEIGHT( ) 3.07 DIMENSION LINES MUST BE ESTABLISHED BEFORE FILLETS,

ROUNDS AND ARROWHEADS ARE ADDED( ) 3.08 DIMENSIONS MUST BE AT LEAST 3/8" APART( ) 3.09 LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

14

MISOE NO.


PSOE CODE NO(S)

1.00 CONDITION


TERMOB NO. 10-048

2.00 PERFORMANCE


3.00 EXTENT


15u

PROGRAM DRAFTING DIVISION---b6 WORKING DRAWINGS


1.00 CONDITION

TERMOB NO. 10-049

( ) 1.01 DESIGN LAYOUT OF COMPOUND "V" CLAMP( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE .

-CENERALSTATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE DETAIL DRAWING OF COMPOUND "V" CLAMP ACCORDING TO


( ) 2.02 DRAW TITLE BLOCK( ) 2.03 DETERMINE NUMBER OF VIEWS( ) 2.04 MAKE ROUGH SKETCH OF DRAWING FOR POSITIONING OF- VIEWS( ) 2.05 DRAW MAIN CENTER LINES STARTING WITH CHARACTERISTIC

VIEW( ) 2.06 CONSTRUCT OBJECT LINES( ) 2.07 ADD FILLETS, ROUNDS AND ARROWHEADS( ) 2.08 ADD DIMENSIONS AND NOTES( ) 2.09 DARKEN ALL SIGNIFICANT LINES

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01 DRAWING MUST BE COMPLETE ENOUGH TO ALLOW MANUFACTURE

OF PART. CORRECT DRAFTING PROCEDURES WILL BE FOLLOWEDWITH THE COMPLETION OF EACH STEP TO BE JUDGED ASSATISFACTORY OR UNSATISFACTORY BY BOARD OF EXPERTRATERS. ALL STEPS TO BE COMPLETED WITHIN 5 HOURS.

( ) 3.02 MUST CONTAIN ALL PERTINENT INFORMATION (TABLE T-3`A)( ) 3.03 DRAWING MUST SHOW CHARACTERISTIC VIEW AND AS MANY

ADDITIONAL VIEWS AS NECESSARY TO SHOW ALL CHARACTERIS-TICS OF PART

( ) 3.04 LAYOUT OF DRAWINC MUST ALLOW ADEQUATE ROOM FOR NOTATIONS( ) 3.05 WORK FROM CHARACTERISTIC (MAIN) VIEW TO OTHER VIEWS

DEVELOPING ALL SIMULTANEOUSLY( ) 3.06 LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT( ) 3.07 DIMENSION LINES MUST BE ESTABLISHED BEFORE FILLETS,

ROUND AND ARROWHEADS ARE ADDED( ) 3.08 DIMENSIONS MUST BE AT LEAST 3/8" APART( ) 3.09 ALL LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

151

_ MISOE NO.

S.


USOE CODE NO(S) UNIT 01 DETAIL DRAWINGS

1.00 CONDITION.

TERMOB NO. 1Q-04

2.00 PERFORMANCE


3.00 EXTENT


-MISOE NO.

PROGRAM DRAFTING DIVISION' 06 WORKING DRAWINGS

1.0() CONDITION

UNIT 02 ASSEMBLY DRAWINGS

TERMOB NO. 10-050

( ) 1.01 DETAIL DRAWINGS OF STAY ROD PIVOT( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

-GENERAL7S:TAEMENT Of-PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE TWO VIEW ASSEMBLY DRAWING OF STAY ROD PIVOT


2.0 DRAW TITLE :LOCK( ) 2.03 CONSTRUCT MAIN VIEW IN rum, SECTION( ) 2.04 CONSTRUCT SECONDARY VIEW( ) 2.05 ADD DIMENSIONS AND NOTES( ) 2.06 IDENTIFY ALL PARTS USING NUMBER CODE( ) 2.07 ;ADD MATERIALS LIST( ) 2.08 DARKEN ALL SIGNIFICANT LINES

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTTNG OUTCOME( ) 3.01 DRAWING MUST ADEQUATELY ILLUSTRATE RELATIONSHIPS OF ALL

PARTS TO SATISFACTION OF BOARD OF EXPERT RATERS.CORRECT DRAFTING PROCEDURE MUST BE FOLLOWED WITH THEPERFORMANCE'OF EACH STEP TO BE RATED AS SATISFACTORYOR UNSATISFACTORY. ALL STEPS TO BE COMPLETED WITHIN10 HOURS.


( ) 3.03 PARTS SHOULD BE SECTIONED USING AMERICAN STANDARoSSYMBOLS

( ) 3.04 EACH VIEW MUST BE CORRECT( ) 3.05 DIMENSIONS WHICH AFFECT SIZE AND LOCATION OF MATING

PARTS MUST BE BASED UPON TOLERANCES WHICH_ARE APPRO-PRIATE TO THE FUNCTION OF PARTS. TAPPING AND GRINDINGMUST BE PROPERLY SPECIFIED

( ) 3.06 ALL PARTS SHOULD BE ASSIGNED A NUMBER AND LISTEDACCORDING TO THAT NUMBER

( ) 3.07 STOCK NUMBERS SHOULD BE OBTAINED CORRECTLY FROMCATALOGUES

( ) 3.08 ALL LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

153

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

MISOE NO.,



TERMOB NO. T0 -05 T-7--


3.00 EXTENT


1 64

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION

DIVISION 06 WORKING DRAWINGS,

UNIT 02 ASSEMBa DRAWINGS

TERMOB 10-051

( ) 1.01 DETAIL DRAWINGS OF FAN ASSEMBLY( ) 1.02 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE


( ) 2.61 MAKE TWO VIEW ASSEMBLY DRAWING OF FAN ASSEMBLY USINGl'HE FOLLOWING PROCEDURE:

( ) 2.011 DRAW TITLE BLOCK( ) 2.03 CONSTRUCT MAIN VIEW IN FULL SECTION( ) 2.04 CONSTRUCT SECONDARY VIEW( ) 2.05 ADD DIMENSIONS AND NOTES( ) 2.06 IDENTIFY ALL PARTS USING NUMBER CODE( ) 2.07 ADD MATERIALS LIST( ) 2.08 DARKEN ALL SIGNIFICANT LINES

3.00 EXTENT


( ) 3.01 DRAWING MUST ADEQUATELY ILLUSTRATE RELATIONSHIPS OFALL PARTS TO SATISFACTION OF BOARD'OF EXPERT RATERS.CORRECT DRAFTING PROCEDURE MUST BE FOLLOWED WITH THECOMPLETION OF EACH STEP TO BE JUDGED AS SATISFACTORYOR UNSATISFACTORY BY BOARD OF EXPERT RATERS. ALLSTEPS TO BE COMPLETED WITHIN 12= HOURS.


( ) 3.03 PARTS SHOULD BE SECTIONED USING 'AMERICAN-STANDARDSSYMBOLS tt

( ) 3.04 EACH VIEW MUST CORRECT TO SATISFACTION OF BOARD OFEXPERT RATERS

( ) 3.05 DIMENSIONS WHICH AFFECT SIZE AND LOCATION OF MATINGPARTS MUST BE BASED UPON TOLERANCES WHICH ARE APPRO-PRIATE TO FUNCTION OF PARTS. SUCH OPERATIONS ASBORING, DRILLING, REAMING, TAPPING AND GRINDING MUSTBE PROPERLY SPECIFIED

( ) 3.06 ALL PARTS MUST BE ASSIGNED A NUMBER AND LISTEDACCORDING TO THAT NUMBER

( ) 3.07 STOCK NUMBERS MUST BE OBTAINED CORRECTLY FROM CATALOGUE

( ) 3.08 ALL *LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

I r0 0

MISOE NO.

PROGRAM, DRAFTING DIVISION 06 WORKING DRAWINGS

USOB CODE NO(S) UNIT 02 ASSEMBLY DRAWINGS

TERMOB NO. 10-051

1.00 CONDITION

2,00 PERFORMANCE


3.00 EXTENT


J

MISOE NO.



TERMOB NO, 10-052

1.00 CONDITION

( ) 1.01 WASHING MACHINE REPAIR MANUAL( ) 1.02 ELECTRONIC HANDBOOK( ) 1.03 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 MAKE A DRAWING OF A LACED ASSEMBLY WIRING HARNESS

ACCORDING TO THE FOLLOWING PROCEDURES:

DRAW TITLE B CK( ) 2.03 DRAW BASIC OUTLINE OF HARNESS FULL SIZE( ) 2.04 DEVELOP HARNESS'S THICKNESS DIMENSIONS( ) 2.05 DETERMINE AND CONSTRUCT BREAKOUT POINTS( ) 2.06 DETERMINE AND CONSTRUCT LOCATIONS OF WIRE TERMINATIONS( ) 2.07 NUMBER AND COLOR CODE EACH WIRE TERMINATION( ) 2.08 CONSTRUCT WIRE IDENTIFICATION TABLE( ) 2.09 COMPLETE DRAWING

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01 DRAWING MUST ACCURATELY ILLUSTRATE FORM AND SIZE OF

HARNESS FOR ASSEMBLY PURPOSES, CORRECT DRAFTINGSTANDARDS WILL BE FOLLOWED AND EACH STEP TO BE JUDGEDAS SATISFACTORY OR UNSATISFACTORY BY BOARD OF EXPERTRATERS. ALL STEPS TO BE COMPLETED WITHIN 4 HOURS.

( ) 3,62 MUST CONTAIN ALL PERTINENT INFORMATION( ) 3.03 CORRECT DIMENSIONS TO BE TRANSFERRED FROM WASHING

MACHINE REPAIR MANUAL( ) 3.04 NUMBER OF WIRES AND THEIR THICKNESS'S TO BE CONSIDERED

( ) 3.05 TO BE COMPUTED FROM INFORMATION SUPPLIED IN WASHINGMACHINE REPAIR MANUAL

( ) 3.06 ALLOWANCES TO BE MADE FOR WIRE STRIPPING( ) 1.-07 MUST COINCIDE WITH CONNECTING POINTS OF COMPONENT( ) 3.08 TABLE MUST COINCIDE WITH HARNESS NUMBERS AND COLOR

CODES( ) 3.09 LINES MUST BE DARK, SHARP, AND OF PROPER WEIGHT

6PI

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

2.00 PEWORMANCE

MISOE NO.



TERMOB NO. 10-052

GENERAL STATEMENT OP PERFORMANCE AND RESULTING OUTCOME

3.00 EXTENT


MISOE NO.

PROGRAM DRAFTING

1.00 CONDITIONIr

DIVISION 06

UNIT 03

TERMOB NO.

WORKING DIOWINGI;

DIAGRAM DRAWINGS

10-053

( ) 1.01 PRELIMINARY SKETCH OF RADIO DIAGRAM( ) 1.02 ELECTRONIC TEMPLATE-( ) 1.03 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 DRAW A SCHEMATIC DIAGRAM OF A SIMPLE RADIO RECEIVER

EMPLOYING THE FOLLOWING OPERATIONS:

) ).02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF SCHEMATIC DIAGRAM( ) 2.04 DRAW ALL BASIC COMPONENTS( ) 2.05 CONSTRUCT ALL INTER CONNECTIONS(') 2.06 DARKEN ALL SIGNIFICANT LINES

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME() 3.01 DRAWING MUST BE IN AGREEMENT WITH THE CIRCUIT SKETCH$ PROVIDED TO APPROVAL OF BOARD OF EXPERT RATER. TO BEq COMPLETED WITHIN 2 1/2 HOURS WITH EACH 'OPERATION'

JUDGED AS SATISFACTORY OR UNSATISFACTORY.

( ) 3.0 ALL PERTINENT INFORMATION MUST BE LISTED TABLE T-3A( ) 3.03 MAJOR SECTIONS AND INDIVIDUAL COMPONENTS MUST BL

SUBDIVIDED FOR LAYOUT PURPOSES( ) 3.04 SYMBOLS AND STANDARDS MUST BE DRAWN WITH ELECTRONIC

TEMPLATE( ) 3.05 ROUTING AND PRE-ROUTING OF CONNECTIONS MUST BE PLANNED

SO THAT ALL PARTS FIT LOGICALLY INTO THE DRAWING( ) 3.06 LINES AND SYMBOLS MUST MEET SPECIFIED STANDARDS AND

CODES

159

PROGRAM psikr ZING

USOE CODE NO (5 )

1.00 CONDITION

2.00 PERFORMANCE

MISOE NQ.


UNIT 03 DIAGRAM DRAWINGS

TERMOB NO,. 1b-053


3.00 EXTENT

r GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME

1 60

MISOE NO.

PROGRAM DRAFTING.

1.00 CONDITION

...0/II-7DIVISION 06

UNIT 04

TERMOB NO.

WORKING DRAWINGS

CONSTRUCTIONDRAWINGS

10-054

001.11411.

( ) 1.01 PRELIMINARY SKETCH OF RANCH HOUSE( ) 1.02 ARCHITECTURAL TEMPLATE( ) 1.03 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 PERFORMANCE,

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.61 DRAW FLOOR PLAN OF RANCH HOUSE EMPLOYING THE FOLLOW-

ING OPERATIONS:

(1 2.02 DRAW TITLE BLOCK( ) 2.03 MAKE ROUGH SKETCH OF LAYOUT( ) 2.04 DRAW OUTSIDE WALL POSITIONS( ) 2.05 ESTABLISH ALL CENTER LINES AND INTERIOR WALLS( ) 2.06 LOCATE ALL DOORS AND WINDOWS( ) 2.07 DRAW LAYOUT FOR KITCHEN AND BATH(S)( ) 2.08 ADD DIMENSIONS AND NOTES( ) 2.09 DARKEN ALL SIGNIFICANT LINES,

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01 DRAWING MUST ADEQUATELY SHOW LAYOUT OF ROOMS AND ALL

DIMENSIONS TO APPROVAL OF BOARD OF EXPERT RATERS.TO BE COMPLETED WITHIN 4 HOURS WITH EACH OPERATIONJUDGED AS SATISFACTORY OR UNSATISFACTORY.

( ) 3.03( ) 3.04( ) 3.05

( ) 3.06( ) 3.07

( ) 3.08

( ) 3.09

ALL PERTINENT INFORMATION MUST BE LISTED TABLE TSKETCH MUST ACCURATELY REPRESENT ROOM LAYOUTSCALE OF DRAWING MUST BE ESTABLISHEDINTERIOR WALL DIMENSIONS MUST BE TAKEN FROM CENTERTO CENTER

FURNITURE PLACEMENT MUST BE CONSIDEREDTRAFFIC PATTERNS AND ACCESSIBILITY TO ROOMS MUST

BE CONSIDEREDTOTAL INTERIOR DIMENSIONS MUST COINCIDE WITH OUTSIDEDIMENSIONS

DRAWING MUST REPRESENT STRUCTURE WHICH CONFORMSWITH LOCAL BUILDING CODES. ALL LINES MUST BE SHARP,CLEAR, DARK AND OF EVEN WEIGHT

1 61

PROGRAM DRAFTING

USOE CODE NO(S)

1.00 CONDITION

2.00 PERFORMANCE

3.00 EXTENT

AISOE NO.


uNrr 04 -COASTROCrICRIZAWINCS

TERMOB NO. 10-054

STATEMENT__OF_ PERFUWANCE AND -RESULTING OUTCOME

GENERAL STATEMENT OF EXTENT AND. EXTENT OF RESULTING OUTCOME

MISOE NO.

PROGRAM DRAFTING

1.00 CONDITION

apaoaa..1.DIVISION 406 WORKING DRAWINGS

UNIT 04 CONSTRUCTION DRAWING':

TERMOB NO.

() 1.01, FLOOR PLAN OF A HOUSE( ) 1.02 ARCHITECTURAL REFERENCE STANDARDS( ) 1.03 BASIC DRAFTSMAN'S SUPPLIES (TABLE T-3)

2.00 .PERFORMANCE


( )2.01 LAY OUT AND DRAW THE Fle1IN6DATION PLAN t'OR A HOUSE TO A

SCALE OF 1/4" TO 1' EMPLOYING THE FOLLOWING OtiERATrONS:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 ROUGH IN OPENINGS IN FOUNDATION( ) 2.04 INDICATE ELECTRICAL AND WATER INLETS( ) 2.05 "ADD NOTES AND DIMENSIONS( ) 2.06 DARKEN SIGNIFICANT LINES

3.00 EXTENT


( ) 3.01 DRAWING MUST SHOW ALL ,CHARACTERISTICS OF FOUNDATIONPLAN TO APPROVAL OF BOARD OF EXPERT RATERS. TO BECOMPLETED WITHIN 6 HOURS WITH EACH OPERATION JUDGEDAS SATISFACTORY OR UNSATISFACTORY.

( ) 3.02 ALL PERTINENT INFORMATION MUST BE LITE D (TABLE T-3A)

( ) 3.03 DRAWING MUST BE PROPERLY CENTERED ON LAYOUT

C ) 3.04 LINES AND SYMBOLS MUST PROPERLY ILLUSTRATE ELECTRICALAND WATER INLETS

( ) 3.05 SYMBOLS AND NOTES MUST BE COMPLETE( ) 3.06 LINES MUST BE SHARP, CLEAR, DARK AND OFEVEN WEIGHT

thi

MISOE NO.


USOE CODE NO(S) UNIT 04 CUSTRUCTIOVDRAtagag----

TERMOB NO. 10-055

1.00 CONDITION

2.00 PERFORMANCE


. -

,3.00 EXTENT


16,1

MISOE NO.

PROGRAM DRAFTING DIVTSION 06 WORKING DRAWINGS

UNIT 04 CONSTRUCTION DRAWINGS

1,00 CONDITION

TERMOB NO.

( 1..01 ROUGH SKETCH DIMENSIONS AND SPECIFICATIONS OF THEBASEMENT OF A TWO-BEDROOM HOUSE

( ) 1.02 -BASIC DRAFTSMAN'S PLIES (TABLE T-3)

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOME( ) 2.01 DRAW PLAN VIEW AND DETAILS OF ABOVE 1/4" TO- 1'

EMPLOYING THE FOLLOWING OPERATIONS:

( ) 2.02 DRAW TITLE BLOCK( ) 2.03 DETERMINE NUMBER OF VIEWS NECESSARY( ) 2.04 LOCATE ALL SUPPORTING BEAMS AND COLUMNS( ) 2.05 LOCATE ALL DOORS, WINDOWS AND SERVICE OPENINGS( ) 2.06 ADD NOTES AND DIMENSIONS( ) 2.07 DARKEN ALL SIGNIFICANT LINES

3.00 EXTENT

GENERAL STATEMENT OF EXTENT AND EXTENT OF RESULTING OUTCOME( ) 3.01,, WALL AND FOOTING THICKNESS MUST BE SHOWN. ALL DETAILS

MUST BE PROPERLY SHOWN TO APPROVAL OF BOARD OF EXPERTRATERS. TO BE COMPLETED WITHIN 8 HOURS WITH EACHOPERATION JUDGED AS SATISFACTORY OR UNSATISFACTORY.


( ) 3.03 VIEWS MUST ADEQUATELY REPRESENT STRUCTURE( ) 3.04 CORRECT SYMBOLS AND LINES MUST BE USED( ) 3.05 DOORS AND WINDOWS MUST BE DETAILED WITH UNIT NUMBERS

ADDED( ) 3.06 TOTAL INTERIOR DIMENSIONS SHOULD AGREE WITH OUTSIDE

DIMENSIONS( ) 3.07 LINES MUST BE SHARP, CLEAR, DARK AND OF EVEN WEIGHT

16'

MISOE NO.


USOE CODE UO(8) UNIT 04 CONSTRUCTION DRAWINGS

TERMOB NO. 10-056

1.00 CONDITION

2.00 PERFORMANCE

GENERAL STATEMENT OF PERFORMANCE AND RESULTING OUTCOMEA

3.00 EXTENT


1 66

TABLE T-3

BASIC DRAFTSMAN'S SUPPLIES

PENCILS -

COMPASS

TRIANGLES

REGULAR CURVES

SCALES

TEMPLATES

LEAD POINTER

ERASING SHIELD

DUST BRUSHES

CLEANING AGENTS

MEDIA (PAPER)

(

1t

7

TABLE T-3A

TITLE BLOCK COMPONENTS

NAME OF PART

NAME OF MACHINE OR STRUCTURE

NAME AND LOCATION OF THE MANUFACTURING FIRM

SCALE

DATE

NAME OR INITIALS OF DRAFTSMAN

DRAWING NUMBER

168

169Table T-4 Additional. TERMOB Performance Statements

This form is provided for the addition of TERMOB performancestatements to ensure more complete coverage of your program. Pleaseprovide a comprehensive performance statement (coded 2.01 on eachTERMOB) for each area of deficiency that you have identified.

The performance Statement need only be listed identified bythe division and unit numbers of the deficient areas; the conditionsand extents will be incorporated later.

1. Division Performance Statement

Unit

2. Division

Unit''

nifisionUr.it

fies.

..11.10111600100. 110/o.

Performance Statement



.1

Unit

Division

Unit

6. Division

Unit

aaaaat en, Mu,


..111111111.=1,


2. Division

Unit

11.11...

=0.dioPerformance Statement

3., r,i.ision Performance Statement

Unit


Unit

MEINY41=IINOOPIIIIMOINIMI.

5. Division

Unit

6. Division

Unit 10

7. Division

Unit




170

T-128

171

Table T-4 (Cont' d) Additional TERMOB Performance Statements

This form is provided for the addition of TERMOB perfotmancestatements to ensure more complete-coverage of your program. Pleaseprovide a comprehensive performance statement (coded 2.01 on eachTERMOB) for each area of deficiency that you have identified.

The performance statement need only be listed identified bythe division and unit numbers of the-deficient areas; the conditionsand extents will be incorporated later.

B. Division

Unit

9. Division

Unit

10. Division

.Unit

Xi. .DiVision

Unit

12. Division

Unit

13. Division

Unit







unit

9. Division

Unit



Unit


Unit


Unit


Unit

14: Division Performance Statement

Unit

T-129

p.

INDEX OF TERMOB STATEMENTS

PROGRAM:

TERMOB NO.

I

DRAFTING

MAKE ISOMETRIC DRAWING OF BEARING

MAKE ISOMETRIC DRAWING OF ARM BRACKET

MAKE ISOMETRIC DRAWING OF WEDGE BLOCK

MAKE A SINGLE LINE ISOMETRIC DIAGRAM DRAWINGOF PIPE LAYOUT

PAGE

10-001

10-002

10 -003

10..004

T.-12

T-14

T -16

T-18

10 -005 MAKE OBLIQUE DRAWING OF BEVELED BLOCK T-20

10-006 MAKE OBLIQUE DRAWING OF INDEX GUIDE T -22

10-007 MAKE OBLIQUE DRAWING OF CONTROL BRACKET T -24

10 -008 MAKE A TWO VIEW SKETCH OF SHAFT SUPPORT T^26

10409 MAKE A TWO POINT PERSPECTIVE SKETCH OFSTEP BLOCK T -28

10.-010 MAKE A ONE POINT PERSPECTIVE SKETCH OFBOX PARALLEL T -30

10 -011 MAKE AN ANGULAR PERSPECTIVE DRAWING OF COTTAGE T -32

10-012 DETERMINE DIMENSIONS OF MACHINIST S CLAMP, T -34

10-013 DETERMINE DIMENSIONS OF A "IT" B CKET T -36

10-014 DETERMINE DIMENSIONS OF LATHE CENTER T -38

10.-015 DIMENSION STAYROD PIVOTi

T -40

10 -016 DIMENSION MACHINIST'S CLAMP T-42

10-017 DIMENSION DRILL PRESS SPINDLE T -44

10-018 DIMENSION DRAWINGS OF HAND GRINDER T -46

10-018 DIMENSION DRAWINGS OF FAN ASSEMBLY T -48

10 -020 MAKE A TWO VIEW, DIMENSIONED DRAWING OF A

WELDED LINK T -50

10 -021 MAKE A THREE VIEW, DIMENSIONED DRAWING OF A

WELDED BRACKET T -52

10 -022 MAKE A TWO VIEW, DIMENSIONED DRAWING OF A

CASTER BRACKET T-54

10-023 DETAIL MILLING JACKT -56

10-024 MAKE TWO VIEW DRAWING OF HAND WHEEL T -58

_-_10025 MAKE TWO VIEW DRAWING OF PULLEY T-60

10 -005

10-006

10-007

10-008

10-009

10-010

10-011

10-012

10-013

10-014

10-015

10-016

10-017

10-018

10-019

10-020

10-021

10-022

10-023

10-024

10-025

10-026

10-027

10-028

10-029

10-030

MAKE OBLIQUE DRAWING OF BEVELED BLOCK T-20

MAKE OBLIQUE DRAWING OF INDEX GUIDE T-22

MAKE OBLIQUE DRAWING OF CONTROL BRACKET T-24

MAKE A TWO VIEW SKETCH OF SHAFT SUPPORT T-26

MAKE A TWO POINT PERSPECTIVE SKETCH OFSTEP BLOCK T-28

MAKE A ONE POINT PERSPECTIVE SKETCH OFBOX PARALLEL T-30

MAKE AN ANGULAR PERSPECTIVE DRAWING OF COTTAGE T-32

DETERMINE DIMENSIONS OF MACHINIST'S CLAMP T-34

DETERMINE DIMENSIONS OF A "T" BRACKET T-36

DETERMINE DIMENSIONS OF LATHE CENTER T-38

DIMENSION STAYROD PIVOT T-40

DIMENSION MACHINIST'S CLAMP T-42

DIMENSION DRILL PRESS SPINDLE T-44

DIMENSION DRAWINGS OF HAND GRINDER T-46

DIMENSION DRAWINGS OF FAN ASSEMBLY T-48

MAKE A TWO VIEW, DIMENSIONED DRAWING OF A

WELDED LINK T-50

MAKE A THREE VIEW, DIMENSIONED DRAWING OF AWELDED BRACKET T-52

MAKE A TWO VIEW, DIMENSIONED DRAWING OF A

CASTER BRACKETT-54

DETAIL MILLING JACK T-56

MAKE TWO VIEW DRAWING OF HAND WHEEL T-58

MAKE TWO VIEW DRAWING OF PULLEY T-60

MAKE A TWO VIEW DRAWING OF CENTER BEARING T-62

MAKE TWO VIEW DRAWING OF CONE PULLEY T-64

DRAW REMOVED SECTIONS OF SPOKE AND RIM OF

HANDWHEELT-66

DRAW TWO REMOVED SECTIONS OF HOOK T-68

DRAW TWO REMOVED SECTIONS OF A CENTERINGBEARING 174 T-70

T-130

175INDEX OF TERMOB STATEMENTS (CONT'D)

PROGRAM:

TERMOB NO.

DRAFTING

DRAW FRONT VIEW ILLUSTRATING METHOD OF

PAGE

10-031SHOWING HOLES T-72

10-032 DRAW A BROKEN OUT SECTION OF VALVE BODY T-74

(2 INCH HORIZONTAL)

10-033 DRAW A BROKEN OUT SECTION OF VALVE BODY(2 INCH GLOBE) T-76

10-034 MAKE A TWO VIEW WORKING DRAWING OF CLAMPBRACKET T-78

10-035 MAKE A DETAIL SECTION DRAWING OF BOX CORNICE T-80

10-036- MAKE DEVELOPMENT FROM A TWO VIEW DRAWING OF.

OBLIQUE CYLINDER T-82

10-037 MAKE DEVELOPMENT OF OBLIQUE CYLINDER- T-84

10-038 MAKE DEVELOPMENT OF RIGHT CONE T-85

10-039 MAKE DEVELOPMENT OF TWO-PIECE ELBOW T-88

10-040 MAKE DEVELOPMENT OF A TRUNCATED CONE T-90

10-041 MAKE DEVELOPMENT OF TRANSITION PIECE T-92

(CONNECTING CIRCULAR AND SQUARE PIPE)

10-042 MAKE DEVELOPMENT OF TRANSITION PIECE(CONNECTING TWO PIPES) T-94

10-043 DRAW AUXILIARY VIEW OF DOVETAIL BRACKET T-96

10-044 DRAW AUXILIARY VIEW OF FENDER BRACKET T-98

10-045 CONSTRUCT A SECONDARY AUXILIARY VIEW OFTHE CROSS ANCHOR T-100

10-046 CONSTRUCT A SECONDARY AUXILIARY VIEW OFTHE 45° ELBOW T-102

10-047 MAKE DETAIL DRAWING OF SPINDLE SHAFT T-104

10-048 MAKE DETAIL DRAWING OF U BLOCK AND CLAMP T-106

10-049 MAKE DETAIL DRAWING OF COMPOUND KV" CLAMP T-108

10-050 MAKE TWO VIEW ASSEMBLY DRAWING OF STAYRODPIVOT T-110

10-051 MAKE TWO VIEW ASSEMBLY DRAWING OF FAN ASSEMBLY T-112

10-052 MAKE A DRAWING OF A LACED ASSEMBLY WIRING

HARNESST-114

_____ImucikjsalmaTic_DIAGRaLOLA,s/MPLE RADIO

BRACKET

10 -035 MAKE A DETAIL SECTION DRAWING OF BOX CORNICE T-80

10-036 MAKE DEVELOPMENT FROM A TWO VIEW DRAWING OFOBLIQUE CYLINDER T-82

10 -037 MAKE DEVELOPMENT OF OBLIQUE CYLINDER T-84

10-038 MAKE DEVELOPMENT OF RIGHT CONE T-85

10-039 MAKE DEVELOPMENT OF TWO-PIECE ELBOW T-88

10-040 MAKE DEVELOPMENT OF A TRUNCATED CONE T-90

10-041 MAKE DEVELOPMENT OF TRANSITION PIECE T-92

(CONNECTING CIRCULAR AND SQUARE PIPE)

10-042 MAKE DEVELOPMENT OF TRANSITION PIECE(CONNECTING TWO PIPES) T-94

10-043 DRAW AUXILIARY VIEW OF DOVETAIL BRACKET T-96

10-044 DRAW AUXILIARY VIEW OF FENDER BRACKET T-98

10-045 CONSTRUCT A SECONDARY AUXILIARY VIEW OFTHE CROSS ANCHOR y T-100

10-046 CONSTRUCT A SECONDARY AUXILIARY VIEW OF

ri

THE 45° ELBOW 'T-102

10-047 MAKE DETAIL DRAWING OF SPINDLE SHAFT T-104

10-048 MAKE DETAIL DRAWING OF U BLOCK AND CLAMP T-106

10-049 MAKE DETAIL DRAWING OF COMPOUND "V" CLAMP ir T-108

10-050 MAKE TWO VIEW ASSEMBLY DRAWING OF STAYROD

PIVOTT-110

10-051 MAKE TWO VIEW ASSEMBLY DRAWING OF FAN ASSEMBLY T-112

10 -052 MAKE A DRAWING OF A LACED ASSEMBLY WIRINGHARNESS

T-114

10-053 DRAW A SCHEMATIC DIAGRAM OF A SIMPLE RADIO

RECEIVERT-116

10.-054 DRAW FLOOR PLAN OF RANCH HOUSE T -118

10-055 LAY OUT AND DRAW THE FOUNDATION PLAN FOR AHOUSE TO A SCALE OF 1/4" TO 1' T-120

10 -056 DRAW PLAN VIEW AND DETAILS OF ABOVE 1/4" TO 1' T-122

(BASEMENT OF TWO-BEDROOM HOUSE)

17 ti

T-131