dial-up networking setup guide 6.41 feb13

Installation Guide

Dial-Up Networking Setup for Windows® XP and Win7

Version 6.41

2 Dia l -Up Networking Setup Gu id e

© 2013 Anite Finland Ltd. All rights reserved.

This manual, as well as the software described in it, is furnished under license and may only be used or copied in accordance with the terms of such license. The information in this manual is intended for informational use only and is subject to change without notice. Anite Finland Ltd assumes no responsibility or liability for any errors or inaccuracies that may appear in this user manual.

Except as permitted by such license, no part of this publication may be reproduced or transmitted in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Anite Finland Ltd.

Windows XP® is a registered trademark of Microsoft® Corporation in the United States and other countries.

Printed in Finland

Revision 6.41.01, Last edited February 2013.

CONTE NTS 3

CONTENTS

INTRODUCTION 6

DEVICE AUTODETECTION 6

MANUAL CONFIGURATION OF A DIAL-UP CONNECTION (XP) 6

MANUAL CONFIGURATION OF DIAL-UP CONNECTION (WIN7) 9

APPLE IPHONE 5 13

BANDRICH BANDLUXE C320 14

BLACKBERRY TORCH 9810 18

DATANG DTM8101/DTM8120/LEADCORE LC8130E 21

HUAWEI EC169/EC169C USB MODEM 24

CHANGING TCP/IP PROPERTIES 28

HUAWEI E180/E169/E182E/E1820/E270+/E367/E392U-12 USB MODEM 30


HUAWEI C7600 33

HUAWEI E398 36


NOKIA 3500/6120/6121/6720(US)/ C5/C5-00.2/C5-03(US)/C5-04/C7-00/E7-00/N80/ N85(US)/N95(US)/N96(US)/N97(US) 41

NOKIA 500 44

NOKIA 6230I 46

NSN USB-LTE 7210 (ALTAIR) 49

MOTOROLA V3X/V3XX/V3XXUS/V9/V9US53

MOTOROLA USBW 25100 57

SAMSUNG Z105/Z107/Z140/Z500/Z560/Z720/ ZV10/ZX20/A707/G800/P920/P940/SHG-T639/SGH-U800/SHG-U900, LG U900/KU950 59

SAMSUNG GALAXY S II SKYROCKET, GALAXY S II (GT-I9210), GALAXY S II HD LTE (SHV-E120S KOREAN VERSION) 62

SAMSUNG GALAXY S III (SGH-I747, SGH-T999, SCH-I535, SPH-L710) 65

SAMSUNG GALAXY S III (GT-I9305), SAMSUNG GALAXY S II NOTE (GT-N7105) 67


SAMSUNG DROID CHARGE 70

QUALCOMM TM6250/6275/6280/7200/8200/ MDM9200/MDM9600 74

LG C676/C680/VX8300/U900/KU950/KX206/KX256/ KF700/TU550 77

LG VX8350/VX8360 81

LG L1000 84

LG G7/G13/G17 87

LG P930 90

LG VL600 93

LG P500H 97

OPTION GLOBETROTTER 3G+/GT MAX 7.2 READY/HSDPA 7.2/EXPRESS 7.2 99

OPTION ICON 452 101

OPTION GLOBESURFER ICON 7.2 USB MODEM 103

SIERRA WIRELESS AIRCARD 306/307/308/309/310/ 312U/313U/320U/330U, SIERRA COMPASS 889 HSPA USB MODEM, SIPTUNE SM215 108

SIERRA WIRELESS AIRCARD 850/860 112

SIERRA WIRELESS AIRCARD 880/881 114

SIERRA WIRELESS COMPASS 885 116

SIERRA WIRELESS COMPASS 597 118

MERLIN U530/U740/X950D 120

NOVATEL OVATION MC930D/MC990D/MC996D/MC998D/MC545 122

NOVATEL OVATION MC727/MC760 USB MODEM 124

ZAPP TELEMODEM Z020 126

AUDIOVOX PC5750/PANTECH PX-500 130

PANTECH UM175 133

PANTECH UML290 136

ZTE MF820T/MF820D 140

ZTE MF668A 141

ZTE MF683 142

CONTE NTS 5

ZTE MF880 143

ZTE TU25 144

SONY ERICSSON XPERIA ARC S 146

ONDA MT689DC 155

APPLICATION TESTER 157


INTRODUCTION

The purpose of this document is to give step-by-step instructions for setting up dial-up networking for your computer in order to perform packet-switched data testing with the Nemo tool Nemo Outdoor. Furthermore, some of the test mobiles need to be configured before data testing is performed. The configuration instructions are provided in this document.

The usage of Nemo Outdoor is not explained in this document. The Nemo Outdoor User Manual included in the shipment gives detailed information on the Nemo Outdoor software and its usage.

DEVICE AUTODETECTION

From Nemo Outdoor 5.60 onwards, it is possible to use autodetection to add devices to Nemo Outdoor. It is no longer necessary to manually install and configure a dial-up connection. Once a device is connected to a computer and the device driver is installed, it can be added fully automatically to Nemo Outdoor application using Autodetect Devices button. Nemo Outdoor will automatically detect the device trace and modem ports and assign a suitable dial-up connection.

Autodetection works with all Nemo Outdoor test terminals verified by Anite Finland. In some cases it is possible that the terminal is not recognized and the autodetection does not work. If this happens, manually select the correct trace and modem ports. Then select Automatic in the Packet switched dial-up connection field and click Apply. If the automatic dial-up connection detection does not work, please see instructions below.

MANUAL CONFIGURATION OF A DIAL-UP CONNECTION (XP)

1. Select Start | Settings | Control Panel. Click on Network Connections. Select File | New Connection to start the New Connection Wizard. Click Next on the Welcome page.

2. Select Connect to the network at my workplace and click Next.

3. Select Dial-up connection as your Network Connection. Click Next.

INTRODUCTION 7

4. Select the terminal from the list and click Next.

♦ With Leadcore terminals, select the unnumbered Leadcore Technology DTM8100 Modem item, and click Next.

♦ With Nokia terminals, select the item with the highest number and click Next.

♦ With Nokia 7376 terminal, select the unnumbered Nokia USB Modem item and click Next.

5. Type a connection name, for example, Huawei, in the Company Name field. Click Next.

6. In the Telephone Number field, enter *99# (#777 for CDMA mobiles). Click Next.


7. Select Anyone’s use and click Next and Finish.

8. See chapters from page 13 onwards for terminal-specific instructions on adding terminals to Nemo Outdoor.

INTRODUCTION 9

MANUAL CONFIGURATION OF DIAL-UP CONNECTION (WIN7)

Select Start | Control Panel | Network and Internet. Select Network and Sharing Center | Set up a 1.new connection or network. Select Set up a dial-up connection, and click Next.

Select the correct terminal from the list and click Next. 2.With Nokia terminals, select the item with the highest number, e.g., in this case #3.


In the Telephone Number field, enter *99# (#777 for CDMA terminals). In the Connection name 3.field type, for example, Nokia Dial-up connection. Select Allow other people to use this connection. Click Connect.

Click on Skip in the Connecting to xxx dial-up connection dialog. 4.

Click Close. 5.

INTRODUCTION 11

Go to Control Panel | Network and Internet | Network and Sharing Center, and select Connect to a 6.network. Right-click on the Terminal Dial-up Connection, and select Properties.

In the Networking tab, deselect the Internet Protocol Version 6 (TCP/IPv6) item and select 7.Internet Protocol Version 4 (TCP/IPv4). Click OK.

♦ Steps 8 and 9 apply only to Nokia terminals.


Go to Device Manager (Start | Settings | Control Panel | System and Security | Device 8.Manager), and double-click on Modems. Right-click on the #3 item on the list and click Properties.

Select the Advanced tab, and type in atz in the Extra initialization commands field, and click on 9.OK.

See the following chapters for terminal-specific instructions on adding terminals to Nemo Outdoor. 10.

Apple iPhone 5 13

APPLE IPHONE 5

Apple iPhone 5 can be connected with Nemo Outdoor using the application tester handler.

Install iTunes on your computer. iTunes can be downloaded from 1.http://www.apple.com/itunes/download. Start iTunes.

On the iPhone 5 device, select Settings | Personal Hotspot and turn on the Personal Hotspot. 2.

Connect the USB connectivity cable to your PC. Device drivers are installed automatically. 3.

Go to Nemo Outdoor and select Measurement | Add New Device | Phone | Application Tester. 4.

Leave the Trace Port and Modem Port fields empty. 5.

Select <LAN> as the Packet switched dial-up connection. Click OK. 6.

♦ Activate a packet session manually before running scripts.

♦ Note that when testing with iPhone 5, all other connections (WLAN, Ethernet cable, etc.) need to be disconnected.

http://www.apple.com/itunes/download


BANDRICH BANDLUXE C320

Plug in the USB device in one of your PC’s USB ports. The drivers are automatically installed, and 1.Windows automatically detects the device.

Select English in the Choose Setup Language dialog. 2.

Click on Next in the Welcome dialog that appears. 3.

Select I accept the terms in the license agreement in the License Agreement dialog, and click 4.Next.

Bandrich BandLuxe C320 15

Select a destination folder and click Next. 5.

Click Install to start the installation. 6.


Click Finish to finish the installation. 7.

Close the BandLuxe software that appears, as it will not be required in the following steps. 8.

Go to Start | Control Panel | System | Hardware | Device Manager. Under Modems you should be 9.able to see the BandLuxe 3.5G Modem, under Network adapters you should see the BandLuxe 3.5G Ethernet Adapter, and under Ports the BandLuxe Adapter Control Interface (COMxx) and BandLuxe AT CMD Interface (COMxx) items.

Bandrich BandLuxe C320 17

In Nemo Outdoor Device Configuration dialog, select the COM port number assigned to the 10.BandLuxe Adapter Control Interface item in the Trace Port field. Select the COM port number assigned to the BandLuxe 3.5G Modem item (right-click the item and select Properties) in the Modem Port field.


BLACKBERRY TORCH 9810

♦ Please note that currently the driver can be installed on 32-bit Windows only.

Install the device drivers. The file is located on the Nemo Outdoor installation CD. Browse the file 1.manually and double-click the 610_b038_multilanguage file. The package will self-extract.

The Blackberry Desktop Software application is launched. Select the installation language and click 2.OK.

If the installer requests to install the Microsoft Visual C++ 2008 Redistributable file, click Install. 3.

Click Next to begin the Blackberry Desktop SW installation. 4.

Select your country or region and click Next. 5.

Blackb erry Torch 9180 19

Accept the license agreement and click Next. 6.

Select the installation folder and click Next and Install. 7.

Wait until the installation is complete and click Finish. 8.

Close the Blackberry software that appears, as it will not be required in the following steps. 9.


Go to Device Manager. Under Modems you should see the Standard Modem item and under Ports 10.two RIM Virtual Serial Port v2 items.

Connect the device USB cable to the device and to the Nemo Outdoor laptop. Select USB Drive 11.from the device screen.

Start Nemo Outdoor. Autodetection does not work with the Blackberry device so add the device 12.manually (Add New Device | Phone | Qualcomm).

In the Device Configuration dialog, select the COM port with the bigger number assigned to the 13.RIM Virtual Serial Port v2 item in the Trace Port field. Select the COM port with the smaller number in the Modem Port field. Select Automatic in the dial-up connection field.

Datan g DTM8101/DTM8120, Leadcore LC8130E 21

DATANG DTM8101/DTM8120/LEADCORE LC8130E

∇ Installing the connectivity cable driver:

♦ Do not connect the connectivity cable to your PC until the driver installation is complete.

1. The connectivity cable driver is located on the Nemo Outdoor installation CD. Browse the file manually and double-click the USB2VCOM_driver_x.xx.xx file (x is the latest driver version).

2. Select Uninstall old version first if installed, and click Install in the Leadcore Technology DTM8100 Series Driver Installer dialog.

3. In the VCOM Number field you need to select 3 ports for each test terminal. Since the driver is installed only once, select the number of COM ports according to how many Leadcore terminals you intend to use with Nemo Outdoor. Hence, if you want to connect two Leadcore terminals with Nemo Outdoor, select at least 6 in the VCOM Number field. Click Exit when the installation is done.

4. After the driver installation is finished, Windows may restart your computer but it is not required.

5. After your computer has restarted, connect the connectivity cable to the mobile and the other end to the computer’s USB port. Windows will detect the new hardware automatically and start the installation. The step is repeated several times until all new hardware is added.

6. In the Welcome page, select No, not this time and click Next.


7. Select Install the software automatically (Recommended) and click Next.

8. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 6, 7 and 8 several times until the installation process is finished.

9. After installation, go to Device Manager. Select Start | Settings | Control Panel | System, open the Hardware tab and click the Device Manager button.

10. You should be able to see three Datang Mobile modems under Modems, and three Datang Mobile items under Ports.

Datan g DTM8101/DTM8120, Leadcore LC8130E 23

11. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager you will find the COM port numbers needed in the next steps.

12. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the terminal. Click Next.

13. In the Device Manager click on Ports. Select the COM port number assigned to the Leadcore Technology DTM8100 Modem #2 item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Leadcore Technology DTM8100 Modem #3 item in the Modem Port field.

14. In the Device Configuration dialog, select <Automatic> or the previously made dial-up connection as the Packet switched dial-up connection (see page 6). Click Apply.

15. If the device connecting fails, check that you have selected the correct COM ports and try again.


HUAWEI EC169/EC169C USB MODEM

♦ Applies to all 3G and 4G Huawei USB modems. The Huawei Connection Manager starts up every time the device is plugged in and it must be closed in order to be able to use the device with Nemo Outdoor. As a workaround, the Connection Manager .exe file can be renamed. A reinstall warning will be displayed when device is plugged in but this can be ignored.


Next, ignore and close the Mobile Partner application that appears. It should not be on while 2.connecting the device with Nemo Outdoor later on.

You may need to restart the computer for the installation to take effect. 3.

Go to Start | Control Panel | System | Device Manager. You should see the Huawei Mobile 4.Connect – 3G Modem item with its associated COM port number in the list.

The Installer Language view appears. Select language and click OK. 5.

The ChinaNet Client setup view appears. Once you have read the license agreement, select I 6.already read an agreement,and accept all above all agreement clauses and click Next.

Huawei E C169/E C169C USB Mod em 25

Choose the target location where the installation program will install the software and click Next. 7.

The installation begins. Once the installation has been completed, choose if you want to restart the 8.computer or not. Then click Finish.


Once the installation has been completed, the ChinaNet view appears. Choose which network you 9.want to connect to by clicking the Connect button of your chosen connection.

Once you have clicked close button, select Exit ChinaNet and Do not notice me again options 10.and click Ok.


The Mobile Partner view opens. Select Tools | Options. 11.

The options dialog opens. Select Network and select Hybrid as network type. Click OK. 12.


Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager you will 13.find the COM port numbers needed in the next steps.

Select Measurement | Add New Device. In the New Device dialog, click Phones and select the 14.Qualcomm item. Click Next.

In the Device Manager click on Ports. Select the COM port number assigned to the Huawei 15.CDMA Handset – Application Interface item In the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.



CHANGING TCP/IP PROPERTIES

♦ Applies to all 3G and 4G Huawei USB modems with Nemo Outdoor 6.30 and older versions. Before measurements can be done with Nemo Outdoor, the Internet protocol properties must be manually changed to automatic mode. This must be done always after the modem is disconnected/reconnected and also if the device stops responding during measurements.

∇ Windows XP:

Plug in the Huawei device. 1.

Go to Start | Control Panel | Network Connections, and right-click on Huawei Broadband 2.Connection, and select Properties.

In the Mobile Broadband Connection Properties dialog, select Internet Protocol Version 4 3.(TCP/IPv4) and click on Properties.

Select Obtain an IP address automatically and Obtain DNS server address automatically. 4.


∇ Windows 7:


Go to Start | Control Panel | Network and Internet | Network and Sharing Center. 2.

Click on Change adapter settings. 3.

Right-click on Mobile Broadband Connection and select Properties. 4.


Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK 6.and OK.


HUAWEI E180/E169/E182E/E1820/E270+/E367/E392U-12 USB MODEM



Next, ignore and close the Vodafone or Mobile Partner application that appears. It should not be on 2.while connecting the device with Nemo Outdoor later on.

You may need to restart the computer for the installation to take effect. 3.

Go to Start | Control Panel | Phone and Modem Options | Modems. You should see the Huawei 4.Mobile Connect – 3G Modem item with its associated COM port number in the list.


Select Measurement | Add New Device. In the New Device dialog, click Phones and select the 6.Qualcomm item. Click Next.

In the Device Manager click on Ports. Select the COM port number assigned to the Huawei 7.Mobile Connect – 3G Application Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number attached to the Huawei Mobile Connect – 3G Modem item in the Modem Port field.

In the Device Configuration dialog, select <Automatic> or the previously made dial-up 8.connection as the Packet switched dial-up connection (see page 6). Click Apply.

If the device connecting fails, check that you have selected the correct COM ports and try again. 9.




∇ Windows XP:





∇ Windows 7:






HUAWEI C7600 33

HUAWEI C7600

♦ Do not connect the USB data cable to your PC until the driver installation is complete.

1. The data cable driver is located on the Nemo Outdoor installation CD. Browse to folder D:\Drivers\Drivers for Qualcomm Based Devices\Huawei C7600 and run the driver .exe file.

2. Click Install in the DriverInstall Setup: Installation Options dialog.

3. Click Close in the DriverInstall Setup: Completed dialog.

4. After the installation has finished, connect the USB connectivity cable to your phone, and the other end of the cable to your computer’s USB port. Windows will detect the new hardware automatically and start the installation.




7. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 5, 6 and 7 several times until the installation process is finished. Click Finish to exit the wizard.


9. You should see the HUAWEI CDMA Handset – Modem item under Ports.

HUAWEI C7600 35


11. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Qualcomm item. Click Next.

12. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei CDMA Handset – Application Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number attached to the Huawei CDMA Handset - Modem item in the Modem Port field.




HUAWEI E398


1. Connect the device to your computer’s USB port. Windows will detect the new hardware automatically and start the installation. Click Run AutoRun.exe and follow the instructions on the screen.

2. When the installation is finished, Windows XP users are advised to reboot the computer.

3. The Telenor Mobile Partner software starts up. Close the program.

HUAWEI E398 37

4. Go to Control panel | Network and Internet | Network and Sharing Center | Change adapter settings. Right-click on Mobile Broadband Connection (Huawei Mobile Connect – Network Card) and select Properties. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. Select the Obtain and IP address automatically and Obtain DNS server address automatically options.

♦ Please note that these settings must be reselected every time the device is unplugged and reconnected.


6. You should see the Huawei Mobile Connect – Modem item under Modems and the Huawei Mobile Connect – Application Interface and Huawei Mobile Connect – PC UI Interface items under Ports.




9. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei Mobile Connect – PC UI Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Huawei Mobile Connect - Modem item in the Modem Port field.

10. In the Device Configuration dialog, select <NDIS> as the Packet switched dial-up connection. Click Apply.





∇ Windows XP:





∇ Windows 7:






Nokia 3500/6120/6121/6720(US)/C5/C5 -00.2/C5-03(US)/C5-04/C7-00/E 7-00/N80/N85(US)/ N95(US)/N96(US)/N 97(US) 41

NOKIA 3500/6120/6121/6720(US)/ C5/C5-00.2/C5-03(US)/C5-04/C7-00/E7-00/N80/ N85(US)/N95(US)/N96(US)/N97(US)


♦ Do not connect the USB connectivity cable to your PC until the driver installation is complete.

♦ With Nokia C5-03(US), C5-04, C7-00 and E7-00 the following settings are recommended to improve stability:

• Set Theme effects to OFF • Set Animated background to OFF • Set Call image to none • Set Screen saver to none • Delete additional home screens • Set widgets to offline mode • Set WLAN scanning to OFF • Set sensors to OFF 1. The connectivity cable driver is located on the Nemo Outdoor installation CD. Browse to folder

Nemo Outdoor x.xx\Drivers\Nokia drivers and run the Nokia_Connectivity_Driver_xxx.x.msi file (x is the latest driver version).

2. Click Next in the Welcome dialog. Select I accept… in the License Agreement dialog and click Next.

3. Please read the safety notes carefully and then click Next in the Safety Information dialog.

4. Choose the destination folder and click Install.

5. Click Yes in the Digital Signature Not Found dialog if it appears. Otherwise, click Install.


6. After the connectivity cable driver installation is finished, Windows may restart your computer but it is not required.

7. After your computer has restarted, connect the connectivity cable to the mobile and the other end to the computer’s USB port. Windows will detect the new hardware automatically and start the installation. The step is repeated several times until all new hardware is added.

♦ Please note that with newer Nokia devices the Wizard may not appear at all and instead the installation is performed automatically.



10. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 8, 9, and 10 several times until the installation process is finished.


12. Under Wireless Communication Devices you should see the Nokia xxxx USB Phone Parent item. Under Modems, you should see three Nokia xxxx (USB) items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

Nokia 3500/6120/6121/6720(US)/C5/C5 -00.2/C5-03(US)/C5-04/C7-00/E 7-00/N80/N85(US)/ N95(US)/N96(US)/N 97(US) 43

13. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the terminal. Click Next.

14. In the Device Manager click on Modems. Select the COM port number assigned to the first/unnumbered Nokia xxx USB item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the second highest Nokia xxx USB item in the Modem Port field.




NOKIA 500



1. The connectivity cable driver is located on the Nemo Outdoor installation CD. Browse to folder Nemo Outdoor x.xx\Drivers\Nokia drivers\Nokia 500 and run the Nokia_Suite_webinstaller_All file.

2. When the installation starts, choose your language and click Install.

3. Click I accept.

4. After the Nokia Suite installation is finished, close the installation dialog and connect the connectivity cable to the mobile and the other end to the computer’s USB port. Windows will detect the new hardware automatically and install the drivers.

5. After installation, go to Device Manager. Under Wireless Communication Devices you should see the Nokia xxxx USB Phone Parent item. Under Modems, you should see three Nokia xxxx (USB) items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


Nokia 500 45

7. In the Device Manager click on Modems. Select the COM port number assigned to the first/unnumbered Nokia xxx USB item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the second highest Nokia xxx USB item in the Modem Port field.




NOKIA 6230I



The connectivity cable driver is located on the Nemo Outdoor installation CD. Browse the file 1.manually and double-click the Nokia Connectivity Drivers xx_xx_xxx.exe file (x is the latest driver version).

Click Next in the Welcome dialog. Select I accept… in the License Agreement dialog and click 2.Next.

Choose the destination folder and click Install. 3.

Click Continue anyway in the Software Installation dialog if it appears. 4.

After the connectivity cable driver installation is finished, Windows may restart your computer but it 5.is not required.

After your computer has restarted, connect the connectivity cable to the mobile and the other end 6.to the computer’s USB port. Windows will detect the new hardware automatically and start the installation. The step is repeated several times until all new hardware is added.

In the Welcome page, select No, not this time and click Next. 7.

Nokia 6230i 47

Select Install the software automatically (Recommended) and click Next. 8.

Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation 9.dialog if it appears. You may need to repeat steps 7, 8 and 9 several times until the installation process is finished.

After installation, go to Device Manager. Select Start | Settings | Control Panel | System, open 10.the Hardware tab and click the Device Manager button.

Under Wireless Communication Devices you should see four Nokia xxxx USB items. If the 11.installation was successful, the Nokia xxxx USB Phone Parent item should be on the list. Under Modems, you should see two Nokia xxxx (USB) items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click 12.Phones and select the terminal. Click Next.

In the Device Manager click on Modems. Select the COM port number assigned to the numbered 13.Nokia 61xx (USB) item in the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the unnumbered Nokia 61xx (USB) item in the Modem Port field.



NSN USB-l te 7210 49

NSN USB-LTE 7210 (ALTAIR) ♦ Do not connect the USB connectivity cable to your PC until the driver installation prompts you

to do so.

1. First the Connection Manager is installed. The installation file is located on the Nemo Outdoor installation CD. Browse the file and double-click the LTE7210_xxxx_EngineeringRelease.exe file (xxxx refers to the version number).

2. First select the Installer language and click OK.

3. Click Next in the Welcome dialog. Click I Agree in the License Agreement dialog.

4. Choose the destination folder and click Next.

5. If at some point you see the Select Components dialog, select Full Installation and click Next.


6. Define the Start Menu Folder and click Install.

7. At some point during the Connection Manager installation, the Device Driver Installation Wizard starts up automatically. Click Next in the Welcome dialog.

NSN USB-l te 7210 51

8. The device driver installation is completed and you can now connect the device to your computer. Click Finish.

9. Windows will automatically detect the new hardware and install the required drivers.

10. Return to the Connection Manager installation. When the installation is complete, click Finish.


11. The Connection Manager will launch automatically but it is important that it is closed before adding the device to Nemo Outdoor. It is recommended that you rename the .exe file that launches the Connection Manager to prevent the CM from starting. Browse to C:\Program Files \NSN LTE Connection Manager (or for 64-bit Windows C:\Program Files (x86)\NSN LTE Connection Manager) and rename the nsnltecm.exe to nsnltecm.exe_.

12. To avoid performance issues with the modem, the Altair LogCreator standalone functionality needs to be disabled. Browse to folder C:\Program Files\NSN LTE Connection Manager\Tools\ Internals\LogCreator and open file RunLogCreator.bat with Notepad. Modify the following string:

• Original: LogCreator.exe -SA -FN:"50" -E -Y4:"LOG_SOCK_IF" -D4:".\LoggerDB\LTELogDB.txt" -D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"

• Modified: LogCreator.exe -E -Y4:"LOG_SOCK_IF" -D4:".\LoggerDB\LTELogDB.txt" -D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"

13. Go to Device Manager. Under Ports you should see Nokia Siemens Networks LTE Application Interface item.

14. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select Altair. Click Next.

15. In the Nemo Outdoor Device Configuration dialog, define the following settings:

• Trace port: Select Altair USB • Modem port: Select the COM port number assigned to the Nokia Siemens Networks LTE

Application Interface 16. In the Device Configuration dialog, select <NDIS> and click Apply.

17. If the device connecting fails, check that you have selected the correct COM ports and try again. Also check that the NSN Connection Manager is not running.

Motoro la V3X/V3XX(US)/V9(US) 53

MOTOROLA V3X/V3XX/V3XXUS/V9/V9US ∇ Installing the connectivity cable driver:


1. The connectivity cable driver is located on the Nemo Outdoor installation CD. Browse the file manually and double-click the Motorola_End_User_Driver_Installation_x.x.x.msi file (x is the latest driver version).

2. Click Next in the Welcome dialog. Select I agree… in the License Agreement dialog and click Next.

3. Click Close in the Installation Complete page.

4. After the installation has finished, connect the USB connectivity cable to your phone, and the other end of the cable to your computer’s USB port. Windows will detect the new hardware automatically and start the installation.




7. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 5, 6 and 7 several times until the installation process is finished. Click Finish to exit the wizard.


9. Under Modems You should see the Motorola USB Modem item.

Motoro la V3X/V3XX(US)/V9(US) 55

10. Under Ports you should see Motorola Network Monitor. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


12. In the Device Manager click on Modems. Select the COM port number assigned to the Motorola Network Monitor item in the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Motorola USB Modem item in the Modem Port field.

Motoro la USBW 25100 57

MOTOROLA USBW 25100


Run the ClearCM_v1.05.0035.exe file on the Nemo Outdoor installation CD. 1.

Wait until extraction and installation finishes (no input from user required) and until Clear 2.Connection Manager starts up.

When CLEAR Connection Manager is running (no device detected), connect the device to a free 3.USB port.

The Connection Manager automatically installs the drivers; when done, it will start searching for a 4.network.

Go to Device Manager in Start | Settings | Control Panel | System | Hardware. Double-click on 5.the Network adapters item. The WiMAX Network Adapter item should be in the list.



Select Measurement | Add New Device. In the New Device dialog, click Phones and select the 7.terminal. Click Next.

In the Device Manager click on Modems. Select the BECEEM USB in the Trace Port field in the 8.Device Configuration dialog. Leave the Modem Port field empty.

In the Device Configuration dialog, select <Automatic> or the previously made dial-up connection 9.as the Packet switched dial-up connection (see page 6). Click Apply.


♦ Note that the connection must be activated via the Clear Connection Manager, which also needs to be running during measurements, for the device to work with Nemo Outdoor.

Samsun g Z105/Z107/Z140/Z500/Z560/Z720/ZV10/ZX20/A707/G800/P920/P940/SGH -T639/SGH -U800/SGH-U900, LG U900/KU950 59

SAMSUNG Z105/Z107/Z140/Z500/Z560/Z720/ ZV10/ZX20/A707/G800/P920/P940/SHG-T639/SGH-U800/SHG-U900, LG U900/KU950


1. Insert the Nemo Outdoor installation CD-ROM in the CD-ROM drive. Browse to folder D:\Drivers\Qualcomm Specific Softwares.

2. Double-click the QCUSBCompositeHostDriverxxxx.exe file. Click Unzip. This will extract files to folder C:\QualcommCompositeUSB29xx (x being the latest version). Click Close.

3. Switch on the mobile. Connect the PCB157ULE USB cable to the mobile and the other end of the cable to a USB port on your computer.

4. Windows will automatically detect the new hardware. Select No, not this time and click Next.

5. Select Install from a list or specific location and click Next.

6. Select the Include this location in the search option and browse to folder C:\QualcommCompositeUSB2029\HK11-V3865-21_2.0.29\WinXP\free. Click Next.


7. The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new hardware is ready to be used. If the Hardware Installation dialog appears, click Continue Anyway.

8. When the installation is complete, check from the Device Manager (Start | Settings | Control Panel | System | Hardware | Device Manager) that the installation was successful. Under Modems you should see the Qualcomm USB Modem item and under Ports you should see the Qualcomm Diagnostics Interface item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

9. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Qualcomm item. Click Next.

10. In the Device Manager click on Modems. Select the COM port number assigned to the Qualcomm Diagnostics Interface item in the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Qualcomm USB Modem 3197 item in the Modem Port field.

Samsun g Z105/Z107/Z140/Z500/Z560/Z720/ZV10/ZX20/A707/G800/P920/P940/SGH -T639/SGH -U800/SGH-U900, LG U900/KU950 61




SAMSUNG GALAXY S II SKYROCKET, GALAXY S II (GT-I9210), GALAXY S II HD LTE (SHV-E120S KOREAN VERSION)



1. Insert the Nemo Outdoor installation DVD and browse to the driver folder. Double-click the driver file (SAMSUNG_USB_Driver_for_Mobile_Phones) to start the installation. Click Next in the Welcome dialog.

2. Select your language and country from the list and click Next.

3. Select the installation location and click Install.

Samsun g Galaxy S I I Skyrocket , Galaxy S I I (GT- I9210), Ga laxy S I I HD LTE (SHV-E 120S) 63

4. The driver files are installed. Wait until the installation is finished and click Exit.

5. Switch on the mobile. Connect the USB cable to the mobile and the other end of the cable to a USB port on your computer. Wait for Windows to detect the device.

6. When the installation is complete, check from the Device Manager (Start | Settings | Control Panel | System | Hardware | Device Manager) that the installation was successful. Under Modems you should see the Samsung Mobile USB Modem item and under Ports you should see the Samsung Mobile USB Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



8. In the Nemo Outdoor Device Configuration dialog, define the following settings:

• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port with the bigger port number (in the example above, COM53)

• Modem port: Select the COM port number assigned to the Samsung Mobile USB Modem 9. In the Device Configuration dialog, select <NDIS> or the previously made dial-up connection as

the Packet switched dial-up connection (see page 6). Click Apply.

10. If the device connecting fails, select the Samsung Mobile USB Serial Port with the smaller port number and try again.

Samsun g Galaxy S I I I (SGH-I747, SGH -T999, SCH -I535, SPH -L710) 65

SAMSUNG GALAXY S III (SGH-I747, SGH-T999, SCH-I535, SPH-L710)



♦ If the Samsung Galaxy S III terminal has been used with Nemo Handy, the device needs to restarted or powered off/on before connecting it with Nemo Outdoor.

Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo 1.Outdoor\Nemo Outdoor xx\Drivers and device specific softwares\Qualcomm\Samsung\Samsung Galaxy S III). Double-click the SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe to start the installation.

Click Next in the Welcome dialog. Select language and country. 2.

Select the installation location and click Install. 3.

When the installation is complete, connect the device to the PC. 4.

Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial Port item. 5.Under Modems you should see the Samsung Mobile USB Modem item.

Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click 6.Phones and select the Qualcomm item. Click Next.


In the Nemo Outdoor Device Configuration dialog, define the following settings: 7.

• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port (in the example above, COM34)

• Modem port: Select the COM port number assigned to the Samsung Mobile USB Modem In the Device Configuration dialog, select <NDIS> or the previously made dial-up connection as the 8.

Packet switched dial-up connection (see page 6). Click Apply.


♦ To be able to make voice calls the “Trace interface” call method must be selected from Nemo Outdoor user interface via Advanced Properties (device measurement settings – General properties – Advanced - Voice call method - Trace interface). For Samsung Galaxy S III SGH-T999 and SGH-i747, select Trace interface 2.

Samsun g Galaxy S I I I (GT-I9305), Samsung Ga laxy S I I (GT-N7105) 67

SAMSUNG GALAXY S III (GT-I9305), SAMSUNG GALAXY S II NOTE (GT-N7105)

♦ If the terminal has been used with Nemo Handy, the device needs to restarted or powered off/on before connecting it with Nemo Outdoor.

♦ When the UE is used with Nemo Outdoor, other terminals cannot be used simultaneously in data testing if the NDIS interface is used to activate PS data connection. For example, simultaneous data testing with Huawei LTE modem and Samsung Galaxy S III handset is not possible. It should be noted that the issue does not limit using multiple Galaxy S III terminals for simultaneous data testing or together with non-NDIS terminals, such as, Nokia test terminals.

♦ To be able to make voice calls the “Trace interface 2” call method must be selected from Nemo Outdoor user interface via Advanced Properties (device measurement settings – General properties – Advanced - Voice call method - Trace interface 2).

♦ Automatic answering to incoming calls can be done only when a headset is connected to the terminal. Use the original headset included in the sales package. Connect the headset to the phone and from the phone menu select: Settings -> Call Answering/ Ending-> Press arrow “<” on the left upper corner to go back to previous menu. Select Settings -> Accessibility -> Call Settings -> Accessory Settings For Call -> Automatic Answering. Automatic answering will operate only with the headset connected.

♦ Auto detection should not be used to add the device. Add the device manually.

♦ Check that Enable USB auto tethering option is selected.


♦ USB mode must be RDNIS + DIAG + MODEM. Otherwise handset cannot be used with Nemo Outdoor/ Invex. This is selected automatically when application is installed. Return to main menu.

♦ If data testing is done manually without script files, recording must be started before data protocols can be accessed via Nemo Outdoor. Without recording, the data protocol options in the UI are not available.

♦ The following settings should be activated from the phone for data testing:

• Settings -> More settings -> Mobile networks -> Mobile data enabled-> Enable

• For Samsung Galaxy S III: Settings -> More settings -> Mobile networks -> Network Mode -> AUTO

• For Samsung Galaxy S II Note: Settings -> More settings -> Mobile networks -> Network Mode -> Network Mode -> LTE/GSM/WCDMA (Auto mode)



Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo 1.Outdoor\Nemo Outdoor xxx\Drivers and device specific softwares\Qualcomm\Samsung\Samsung Galaxy S III). Double-click the Kies_x.x.x.exe to start the installation.

Select the installation language. 2.

Select I accept… in the License Agreement dialog and click Next. Wait for the installation to finish. 3.It may take several minutes.

If the Samsung Kies software starts, close the program. If the program suggests a driver update, 4.do not update.

When the installation is complete, connect the terminal to your PC with the USB cable. Windows 5.will install the device drivers automatically.

Samsun g Galaxy S I I I (GT-I9305), Samsung Ga laxy S I I (GT-N7105) 69

Go to Device Manager. Under Ports, you should see the Samsung Mobile USB Serial Port item. 6.


In the Nemo Outdoor Device Configuration dialog, define the following settings: 8.

• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port (in the example above, COM15)

• Modem port: Select Not Used. • Packet-switched dial-up connection: Automatic

Click Apply. 9.

If the device connecting fails, check that you have selected the correct COM ports and try again.10.


SAMSUNG DROID CHARGE



1. Insert the Nemo Outdoor installation DVD and browse to the driver folder. Double-click the driver file (SAMSUNG_USB_Driver_for_Mobile_Phones) to start the installation. Click Next in the Welcome dialog.

2. Select your language and country from the list and click Next.

3. Select the installation location and click Install.

Samsun g Droid Charge 71

4. The driver files are installed. Wait until the installation is finished and click Exit.

5. Switch on the mobile. Connect the USB cable to the mobile and the other end of the cable to a USB port on your computer. Wait for Windows to detect the device.

6. Enable USB tethering from the mobile (Menu – Settings - Wireless & networks - Tethering & portable hotspot, select USB tethering). Wait for Windows to finish the driver installation.


7. When the installation is complete, check from the Device Manager (Start | Settings | Control Panel | System | Hardware | Device Manager) that the installation was successful. Under Network adapters you should see the Samsung Android USB Remote NDIS Network Device item and under Ports you should see the Samsung Android USB Diagnostic Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


9. In the Nemo Outdoor Device Configuration dialog, define the following settings and click Apply:

• Trace port: Select the COM port number assigned to the Samsung Android USB Diagnostic Serial Port (in the example above, COM102)

• Packet switched dial-up connection: Select <Automatic> or the previously made dial-up connection (see page 6).

Samsun g Droid Charge 73


QUALCOMM TM6250/6275/6280/7200/8200/ MDM9200/MDM9600


1. Insert the Nemo Outdoor installation CD-ROM in the CD-ROM drive. Browse to folder D:\Drivers\Qualcomm Specific Softwares.

2. Double-click the QCUSBCompositeHostDriver.exe file. Click Unzip. This will extract files to folder C:\QualcommCompositeUSB20xx (x being the latest driver version). Click Close.

3. Switch on the mobile. Connect the PCB157ULE USB cable to the mobile and the other end of the cable to a USB port on your computer.



6. Select the Include this location in the search option and browse to folder C:\QualcommCompositeUSB2029\HK11-V3865-21_2.0.29\WinXP\free. Click Next.

Qualcomm TM6250/6275/6280/7200/8200/MDM9200/MDM9600 75

7. The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new hardware is ready to be used. If the Hardware Installation dialog appears, click Continue Anyway.

8. When the installation is complete, check from the Device Manager (Start | Settings | Control Panel | System | Hardware | Device Manager) that the installation was successful. Under Modems you should see the Qualcomm USB Modem item and under Ports you should see the Qualcomm Diagnostics Interface item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


10. In the Device Manager click on Ports. Select the COM port number assigned to the Qualcomm Diagnostics Interface item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Qualcomm USB Modem 3197 item in the Modem Port field.

LG C676/C680/VX8300/U900/KU950/KX206/KF700/TU550 77

LG C676/C680/VX8300/U900/KU950/KX206/KX256/ KF700/TU550


♦ Do not connect the USB connectivity cable to your PC until the connectivity cable driver installation is complete.

♦ The LG KF700 USB driver conflicts with the LG USB driver for CDMA terminals. If both drivers are installed on the same computer, the terminals are not detected.

The connectivity cable driver is located on the Nemo Outdoor installation CD. With LG C676, C680, 1.and KX 206, browse to folder D:\Drivers\Qualcomm CDMA drivers, and run the LGUSBModemDriver.exe file. With the LG VX8300 terminal, browse to folder D:\Drivers\Qualcomm US Specific Softwares, and run the LGUSB Driver_Eng__Ver_x.x.exe file (x is the latest driver version). With U900/KU950/KX206/KX256/KF700/TU550, browse to folder D:\Drivers\Qualcomm Specific Softwares\LG USB Driver v.3.35.0.600\Driver and run the Setup.exe file.

On the InstallShield Wizard welcome page click Next. 2.

If a Software Installation warning appears, click Continue Anyway. You may need to repeat this 3.step two or three times.

Click OK in the Information dialog. Next, connect one end of the connectivity cable shipped with the 4.mobile phone to the mobile, and the other end to the computer’s USB port. Windows will detect the new hardware automatically and start the installation.

In the Welcome page, select No, not this time and click Next. 5.



Click Continue Anyway or Yes in the Hardware Installation or Digital Signature Not Found 7.dialog if it appears. You may need to repeat steps 5, 6 and 7 several times until the installation process is finished.

LG C676/C680/VX8300/U900/KU950/KX206/KF700/TU550 79

The USB driver has now been installed. Click Finish. 8.

You need to restart your computer for the installation process to take effect. Click Yes in the 9.System Settings Change dialog.

After installation, select Start | Settings | Control Panel | Phone and Modem Options, then open 10.the Modem tab.

Under the Modem item you should see the created LGE CDMA USB Modem and the port 11.attached to it, in this example COM 17.

Go to Device Manager by selecting Start | Settings | Control panel | System | Hardware. In the 12.Device Manager you should see the LGE CDMA USB Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



In the Device Manager click on Ports. Select the COM port number assigned to the LGE CDMA 14.USB Serial Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.



LG VX8350/VX8360 81

LG VX8350/VX8360


Insert the Nemo Outdoor installation CD-ROM in the CD-ROM drive. Browse to folder 1.D:\Drivers\Qualcomm Specific Softwares\LGUSBModemDriver.exe.

Double-click the .zip file. Click Unzip. This will extract files to a folder in your C drive. Click Close. 2.

Switch on the mobile. Connect one end of the USB data cable to the terminal and the other end to 3.an empty USB port on your PC.

Windows will automatically detect the new hardware. Select No, not this time in the Found New 4.Hardware Wizard and click Next.

Select Install from a list or specific location and click Next. 5.

Select Include this location in the search and browse to folder D:\Nemo Drivers\LG VX8x00 6.driver on the Nemo Outdoor installation CD. Click Next.


The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new hardware is 7.ready to be used.

When the installation is complete, check from the Device Manager that the installation was 8.successful. Under Modems you should see the LGE CDMA USB Modem, and under Ports you should see the LGE CDMA USB Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

LG VX8350/VX8360 83


In the Device Manager click on Ports. Select the COM port number assigned to the LGE CDMA 10.USB Serial Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




LG L1000

♦ Do not plug in the data card before installation!

1. Browse to folder D:\Drivers\LG LTE USB Modem on the Nemo Outdoor product CD. Run the LGE Setup_PcUSBDrv20(xxxxxxxx).msi file to start the installation wizard.

2. Click Next in the Welcome window that appears.

3. Click Install in the Ready to Install window.

4. Click Finish in the InstallShield Wizard Completed window.

LG L1000 85

5. Plug in the data card. Windows will automatically detect the new hardware. Select No, not this time and click Next.

6. Select Install the software automatically and click Next.



9. You should see the LGE USB Modem under Modems, and LG Electronics LTE Miniport Driver under Network adapters. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



11. In the Device Manager click on Modems. Select the port assigned to LGE USB Modem in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.



LG G7/G13/G17 87

LG G7/G13/G17

♦ Please note that you cannot install the G7/G17 and G13 drivers on the same Nemo Outdoor laptop.


1. Browse to folder D:\Drivers\LG LTE USB Modem on the Nemo Outdoor product CD.

• For G7 and G17, run the LGLTEUSBDrivers_V1.0.160.exe file to start the installation wizard. • For G13, run the VZAM_7.6.0.0_2495t_LGLTE.exe file to start the installation wizard.


3. Click Install in the Ready to Install window.


4. Click Finish in the InstallShield Wizard Completed window.

5. Plug in the data card. Windows will automatically detect the new hardware. Select No, not this time and click Next.

6. Select Install the software automatically and click Next.


8. After installation, go to Device Manager. Select Start | Settings | Control Panel | System, open the Hardware tab and click the Device Manager button. For the G7 and G17 devices, you should see the LGE F1 LTE USB CDC Modem Interface and LGE F1 WCDMA USB CDC Modem Interface items under Modems. For the G13 device, you should see the LGE LTE DM Port and LGE USB Modem Port items under Modems. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

LG G7/G13/G17 89

9. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the LG L2000 item. Click Next.

10. In the Device Manager click on Modems. Select the port assigned to LGE F1 LTE USB CDC Modem Interface (LGE LTE DM Port for G13) in the Trace Port field in the Device Configuration dialog. Select the port assigned to LGE F1 WCDMA USB CDC Modem Interface (LGE USB Modem Port for G13) in the Modem Port field.

11. In the Device Configuration dialog, select <Automatic> as the Packet switched dial-up connection (see page 6). Click Apply.



LG P930

♦ Do not plug in the device before installation!

Run the LGUnitedMobileDriver_S4981MAN36AP22_ML_WHQL_Ver_3.6.exe file found on the 1.Nemo Outdoor product CD to start the installation wizard.

First select the setup language and click Next. 2.

Click Next in the Welcome dialog. The driver will be installed. 3.

Click OK in the driver installed successfully message. 4.

LG P930 91

Plug in the device. Enable USB tethering from the mobile (Menu – Settings - Wireless & networks - 5.Tethering & portable hotspot, select USB tethering).

♦ Please note that if the USB connection is disconnected (i.e. device is unplugged), the USB tethering must be re-enabled on the phone in order to use the data connection.

Windows will automatically detect the new hardware. Select No, not this time and click Next. 6.

Select Install the software automatically and click Next. 7.

Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if 8.it appears. You may need to repeat steps 6, 7 and 8 several times until the installation process is finished.

After installation, go to Device Manager. You should see the LGE AndroidNet USB Modem item 9.under Modems and LGE AndroidNet For Diagnostics Port under Ports. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



In the Device Manager click on Modems. Select the port assigned to LGE AndroidNet For 11.Diagnostics Port in the Trace Port field in the Device Configuration dialog. Select the port assigned to LGE AndroidNet USB Modem in the Modem Port field.

Select <Automatic> as the Packet switched dial-up connection (see page 6). Click Apply. 12.

♦ When using the device in LTE, do not issue manual packet session commands. If the connection needs to be disconnected, use Radio On/Off commands.

♦ If you are making voice calls, issue an "ATS0=1" AT command to enable the incoming calls. This must be done every time the phone is restarted.

LG VL600 93

LG VL600


1. Browse to folder D:\Drivers\LG LTE USB Modem on the Nemo Outdoor product CD.

2. Run the VZAM_7.6.3.1_2642c_LGLTE.exe file to start the installation wizard. If the Windows Security dialog appears, click Run.

3. The device drivers are installed first.

4. After the device drivers are installed, the VZAccess Manager installation is started.


6. Select I accept the terms in the license agreement and click Next.


7. Click Next and Next. Select Typical in the Setup Type dialog and click Next and Install. Wait until the installation is ready and click Finish.

LG VL600 95

8. Plug in the USB modem. Windows will automatically detect the new hardware and install drivers. Wait until the installation process is finished.

9. After installation, go to Device Manager. Select Start | Settings | Control Panel | System, open the Hardware tab and click the Device Manager button. You should see the LGE LTE USB Modem Port and LGE LTE DM Port items under Modems.


10. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the LG L2000 item. Click Next.

11. In the Device Manager click on Modems. Select the port assigned to LGE LTE DM Port in the Trace Port field in the Device Configuration dialog. Select the port assigned to LGE USB Modem Port in the Modem Port field.



LG P500h 97

LG P500H

♦ Do not plug in the device before drivers are installed!

1. Browse to folder Drivers and device specific softwares\Qualcomm based devices\LG WCDMA terminals\LG P500H on the Nemo Outdoor product CD.

2. Run the LGAndroidPlatformDriver_WHQL_ML_Ver_1.2_All_Win7.exe file to start the installation wizard. If the Windows Security dialog appears, click Run.

3. After the device driver installation is finished, connect the terminal to the computer with a USB cable. Windows will automatically detect the new hardware and install drivers. Wait until the installation process is finished.

4. After installation, go to Device Manager. You should see the LGE Android Platform USB Modem item under Modems and LGE Android Platform USB Serial Port item under Ports.


6. Select the port assigned to LGE Android Platform USB Serial Port in the Trace Port field in the Device Configuration dialog. Select the port assigned to LGE Android Platform USB Modem in the Modem Port field.


Option Globetrotter 3G+/GT MAX 7.2 Ready/HSDPA 7 .2/Exp ress 7 .2 99

OPTION GLOBETROTTER 3G+/GT MAX 7.2 READY/HSDPA 7.2/EXPRESS 7.2

Plug in the Option GlobeTrotter data card. 1.

Windows will automatically detect the new hardware. Select No, not this time and click Next. 2.

Select Install from a list or specific location and click Next. 3.

Select Include this location in the search and browse for the folder where the driver files are 4.located. Click Next.

The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new hardware is 5.ready to be used. If the Hardware Installation dialog appears, click Continue Anyway.


When the installation is complete, check from the Device Manager (Start | Control Panel | System 6.| Hardware | Device Manager) that the installation was successful. Under Modems you should see the GlobeTrotter Modem Interface item and under Ports you should see the GlobeTrotter Application Interface and GlobeTrotter Diagnostics Interface items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


In the Device Manager click on Ports. Select the COM port number assigned to the Option 8.GlobeTrotter X Diagnostics Interface item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the GlobeTrotter Modem Interface item in the Modem Port field.



Option iCON 452 101

OPTION ICON 452

1. Plug in the Option iCon 452 USB data card. Windows will automatically detect the new hardware. Select No, not this time and click Next.

2. Select the language, and click Next.

3. Select I agree in the GlobeTrotter Connect dialog, and click Install.

4. The installation wizard installs the required software and drivers. Wait until it is completed. Click on Yes to restart your system.

5. After the system is rebooted, Globetrotter Connect will start. You can close the program.

6. Go to Start | Control Panel | System | Hardware | Device Manager. Under modems you should see the Globetrotter GI4xx - Modem Interface item, and under ports the Globetrotter GI4xx - Diagnostic Interface item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



8. In the Device Manager click on Ports. Select the COM port number assigned to the Globetrotter GI4xx - Diagnostic Interface item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Globetrotter GI4xx - Modem Interface item in the Modem Port field.



Option GlobeSu rfer iCON 7.2 USB Mod em 103

OPTION GLOBESURFER ICON 7.2 USB MODEM

1. Plug in the Option GlobeSurfer iCON 7.2 USB modem.

2. Windows will automatically detect the new hardware. The Globetrotter Mobility Manager Installation Wizards appears on the screen. Click Next> to begin installation.

3. Select the I agree option in the License Agreement window and click Next>

4. In the Select Installation Details window you can select where to install the software. Click on Browse to select a different destination, or click Next> to continue.

5. Click Next> to install the application.


6. Click Next> and then Finish in the Installation Completed dialog.

7. When the installation is complete, check from the Device Manager (Start | Control Panel | System | Hardware | Device Manager) that the installation was successful. Under Network adapters you will see the GlobeTrotter HSxPA - Network Interface item. Under Ports you should see the GlobeTrotter HSxPA Application Interface (COMx) item and GlobeTrotter HSxPA Diagnostics Interface (COMx) items. Under Universal Serial Bus Controllers you will also see the GlobeTrotter HSxPA item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

8. Next, go to Start | Control Panel | Phone and Modem Option | Modems. If no GlobeTrotter HSxPA items are visible, click on the Add.. button.


9. In the Install New Modem dialog select Don’t detect my modem; I will select it from a list click Next>.

10. In the Manufacturer view, select Option. In the Models view select the GlobeTrotter HSxPA – Modem Interface item and click Next>.


11. Select the ports appointed to the Application Interface and Diagnostics Interface items earlier, and click Next>.

12. Click Finish to exit the wizard.


13. In Start | Control Panel | Phone and Modem Options| Modems you should now be able to see the GlobeTrotter HSxPA – Modem Interface and GlobeTrotter HSxPA – Modem Interface #2 items and the associated COM port numbers.


In the Device Manager click on Ports. Select the COM port number assigned to the Option 12.GlobeTrotter X Diagnostics Interface item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the GlobeTrotter X Modem Interface item in the Modem Port field.




SIERRA WIRELESS AIRCARD 306/307/308/309/310/ 312U/313U/320U/330U, SIERRA COMPASS 889 HSPA USB MODEM, SIPTUNE SM215

1. Plug in the USB data card. The data card automatically starts the 3G Watcher driver installation. Siptune SM215 comes with its own driver installation software on a separate USB stick. Follow the instructions below.

2. Click OK in the Welcome dialog that appears.

3. Click Next in the Telstra Turbo Connection Manager Welcome window. Note that the name of the installation wizard may vary depending on the operator in question.

Sierra Wire less A ircard 30x/31x/320U/330U, S ierra Compass 889 HSPA USB Mod em, S iptun e SM215 109

4. Select I accept the terms in the license agreement in the License Agreement dialog, and click Next.

5. Click on Finish in the InstallShield Wizard Completed window.

6. Windows automatically detects the device.

7. The driver files are installed.

8. Open the Telstra Turbo Connection Manager main view. Note that the name of the Connection Manager may vary, for example, depending on the operator the device comes equipped with. For example, Sierra Wireless Watcher comes with Sierra 306.

9. Select Tools | Options. In the User Options window, select No in the Autolaunch on device insertion or power-up Do nothing for the On exit field or No in Turn radio off on exit Never for Check for updates


10. When these options are selected, you can close the Telstra Turbo Connection Manager/Watcher application, and the device will work in Nemo Outdoor. However, if these options are not selected, the Telstra Turbo Connection Manager/Watcher application needs to run in the background while conducting measurements with the Sierra device in Nemo Outdoor.

♦ Note that the options may vary depending on the device. For example, with Sierra 306, the Tools button is a spanner icon, and instead of On exit field there is Enable airplane mode on exit which needs to be set to No. In addition, the modem name may change depending on the device, for example, to Sierra Wireless HSPA modem.

11. When the installation is complete, check from the Device Manager that the installation was successful. Go to Start | Control Panel | System and Security | System | Device Manager. Under Modems you should see a Sierra Wireless AirCard HSDPA Modem item and under Ports pay attention to the Sierra Wireless AT Command Port (UMTS) (COMxx) and Sierra Wireless DM Port (UMTS) (COMxx) items. Under Network Adapters you should see the Sierra Wireless HSPA Network Adapter item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

Sierra Wire less A ircard 30x/31x/320U/330U, S ierra Compass 889 HSPA USB Mod em, S iptun e SM215 111


12. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra Wireless DM Port item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Sierra Wireless AT Command Port item in the Modem Port field.




SIERRA WIRELESS AIRCARD 850/860


1. Browse to folder D:\Drivers\Sierra Wireless 850 on the Nemo Outdoor product CD. Run the Driver Installer file to start the installation wizard. Click Next in the Welcome screen.

2. If the Confirm File Replace dialog appears, click Yes. The drivers are installed. There will be no notification that the installation is complete.

3. Plug in the data card. The AirCard 800 Series Watcher will start up. Let it run in the background.



6. Select Include this location in the search and browse to folder D:\Drivers\Sierra Wireless 850\DriverInstaller\Driver on the Nemo Outdoor installation CD. Click Next.

7. The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new hardware is ready to be used.

Sierra Wire less A ircard 850/860 113

8. When the installation is complete, check from the Device Manager that the installation was successful. Under Modems you should see two Sierra Wireless AirCard Modem items and under Ports you should see three Sierra Wireless Application Interface items and a Sierra Wireless Diagnostics Interface item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

9. Start Nemo Outdoor, and make sure that the 3G Watcher application included in the data card package is running. This is required for the data card to function with Nemo Outdoor.


11. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra Wireless Diagnostics Interface item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Sierra Wireless Aircard 3G Modem item in the Modem Port field.




SIERRA WIRELESS AIRCARD 880/881


1. Browse to folder D:\Drivers\3G Watcher_Generic.msi on the Nemo Outdoor product CD. Run the Driver Installer file to start the installation wizard. Click Next in the Welcome screen.

2. Next, select the region where the product was purchased, and click Next. Select I accept the terms in the license agreement in the dialog that follows. Click Next.

3. Click Next to install Sierra Wireless 3G Watcher to the specified folder, or click Change to change the default folder. Click Next, and Install. Click Finish to exit the InstallShield Wizard.

4. Restart the computer.

5. Plug in the data card. Note that when you use the AirCard modem for the first time, it takes a few minutes to locate the network. If your sim card requires a pin code, a prompt asking for it will appear. The 3G Watcher will start up. Let it run in the background.

6. When the installation is complete, go to Start | Settings | Control Panel | System and select Device Manager in the Hardware tab to check that the installation was successful. Under Modems you should see two Sierra Wireless AirCard Modem items and under Ports you should see three Sierra Wireless Application Interface items and five other Sierra Wireless items. Pay attention to the Sierra Wireless AT Command Port (UMTS) and Sierra Wireless DM Port (UMTS) COM port numbers, as they will be selected for the modem and trace ports in Nemo Outdoor respectively. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

7. Start Nemo Outdoor, and make sure that the 3G Watcher application included in the data card package is running. This is required for the data card to function with Nemo Outdoor.

Sierra Wire less A ircard 880/881 115


9. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra Wireless DM Port (UMTS) item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Sierra Wireless AT Command Port (UMTS) item in the Modem Port field.




SIERRA WIRELESS COMPASS 885

Plug in the USB modem to a USB port in your PC. 1.

The computer automatically detects and installs the device. You will need to restart the computer 2.for the installation to take effect.

Go to My Computer and double-click on TRU-Install 3.

Click OK on the 3G Watcher initial window. 4.

Click Next on the welcome page. 5.

On the License Agreement page, select I accept the terms in the license agreement, and click on 6.Install.

The installation of the Sierra 3G Watcher may take a few minutes. 7.

Click Finish to exit the wizard. 8.

When the installation is complete, check from the Device Manager that the installation was 9.successful. Under Modems you should see the Sierra Wireless HSPA Modem item and under Ports you should see the Sierra Wireless AT Command Port (UMTS) (COMx) and Sierra Wireless DM Port (UMTS) (COMx) items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

S ier ra Wire less Compass 885 117

Start Nemo Outdoor, and select Measurement | Add New Device. In the New Device dialog, click 10.Phones and select the Qualcomm item. Click Next.

In the Device Manager click on Ports. Select the COM port number assigned to the Sierra 11.Wireless DM Port item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Sierra Wireless AT Command Port (UMTS) item in the Modem Port field.




SIERRA WIRELESS COMPASS 597

1. Insert the USB data card in a free USB slot on your PC.

2. The Sprint SmartView installation setup starts automatically. Double-click on the setup.exe file, and click Setup.


4. In the License Agreement window, select I accept the terms in the license agreement, and click Next.

5. Click Next in the Destination folder dialog.

6. Click Install.

7. After the installation is completed, the software will ask you to restart your computer. Click Yes.

8. Go to Start | Control Panel | System | Hardware | Device Manager. Double-click on Modems to expand it. You should see the Sierra Wireless Compass 597 EVDO Modem item. You should also see the Sierra Wireless Compass 597 DM Port (COMxx) item under Ports. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

Sierra Wire less Compass 597 119


10. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra Wireless Compass 597 DM Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




MERLIN U530/U740/X950D

1. Plug in the Merlin data card.



4. Select Include this location in the search and browse to folder D:\Drivers\Merlin 3G Datacard Specific Softwares\HSDPA U740\NwtDriverInst_V1.2 on the Nemo Outdoor installation CD. Click Next.


6. When the installation is complete, check from the Device Manager that the installation was successful. Under Modems you should see the Novatel Wireless Merlin HSDPA Modem item and under Ports you should see the Novatel Wireless Merlin HSDPA Status Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

Merl in U530/U740/X950D 121


8. In the Device Manager click on Ports. Select the COM port number assigned to the Novatel Wireless Merlin HSDPA Status Port item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Novatel Wireless Merlin HSDPA Modem item in the Modem Port field.




NOVATEL OVATION MC930D/MC990D/MC996D/MC998D/MC545

1. Prior to plugging the USB modem in your computer, please refer to the Novatel quick start guide included in the product package for computer system requirements.

2. Insert the (U)SIM card supplied by your service provider in the terminal. Please refer to the quick start guide for more detailed instructions as to how to do this.

3. Insert the Novatel Ovation USB modem into your PC USB port.

4. Windows will automatically install the device driver and detect the new device. In addition, it automatically installs MobiLink Lite which is the device software. Ignore this software, and close it. It should not be on when adding the device to Nemo Outdoor.

5. Next, go to Start | Control Panel | Phone and Modem Options | Modems on your PC. The list should display Novatel Wireless Modem item and the associated COM port number, in this case COM26.

6. When the installation is complete, check from the Device Manager that the installation was successful. Under Modems you should see the Novatel Wireless Modem item and under Ports you should see the Novatel Wireless Application Port, Novatel Wireless EAP-SIM Port and Novatel Wireless Status Port items. Under Network adapters you should see the Novatel Wireless Network Adapter item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

Novatel Ovat ion Mod em MC930D/MC990D/MC996D/MC998D/MC545 123

7. Exit the MobiLink Lite application before starting Nemo Outdoor.


9. In the Device Manager click on Ports. Select the COM port number assigned to the Novatel Wireless Application Port item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Novatel Wireless Modem item in the Modem Port field.

10. In the Device Configuration dialog, select <Automatic> or the previously made dial-up connection as the Packet switched dial-up connection (see page 6). For Novatel Ovation 996D and 998D select <Automatic> in the PS Dial-Up Connection field. Click Apply.



NOVATEL OVATION MC727/MC760 USB MODEM

1. Plug in the Novatel Ovation USB modem data card.



4. Select Include this location in the search and browse to folder D:\Nemo Drivers\Novatel MC727 usb drivers on the Nemo Outdoor installation CD. Click Next.


Novatel Ovat ion Modem MC727 125

6. When the installation is complete, check from the Device Manager that the installation was successful. Under Ports you should see the Novatel Wireless Ovation EV-DO Diagnostic Port (COMxx), Novatel Wireless Ovation EV-DO GPS Port (COMxx) and Novatel Wireless Ovation EV-DO Status Port (COMxx)items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


8. In the Device Manager click on Ports. Select the COM port number assigned to the Novatel Wireless Status Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




ZAPP TELEMODEM Z020


♦ Do not connect the USB connectivity cable to your PC until the connectivity cable driver installation is complete. It is recommended that you close all other applications before starting the setup.

The connectivity cable driver is located on the Zapp Telemodem Z020 installation CD. Insert the 1.disk in your CD-ROM drive. When the Z020 EV-DO USB Modem page appears, click on English in the upper right-hand corner of the window if you want to change the language. Select Install Z020 Connect.

Select installer language and click OK. 2.

In the Z020 Connect x.xx.x (x being the latest driver version) window, click Next. 3.

Click I Agree in the License Agreement page. 4.

Choose the destination folder for the installation file, and click Install. 5.

Zapp Telemod em Z020 127

Click Finish to close the setup wizard. 6.

Click OK in the warning message. Attach one end of the connectivity cable to the Telemodem, and 7.the other to your computer. Windows will detect the new hardware automatically and start the installation.

The Found New Hardware Wizard opens. In the Welcome page, select No, not this time and click 8.Next.

.


Select the applicable Windows version from the list and click Next. 10.


Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if 11.it appears.

Click Finish to close the wizard. You may need to repeat steps 10-14 a few times before the 12.installation is complete.

After installation, go to Device Manager. Select Start | Settings | Control Panel | System | 13.Hardware. Under Modems you should see the AnyDATA CDMA USB Modem item and under Ports you should see the AnyDATA CDMA USB Serial Device item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

Zapp Telemod em Z020 129


In the Device Manager click on Ports. Select the COM port number assigned to the AnyDATA 15.CDMA USB Serial Device item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




AUDIOVOX PC5750/PANTECH PX-500

1. Plug in the data card.

2. Windows will automatically detect the new hardware.

3. Select Install the software automatically (Recommended), and click Next.

4. Select Include this location in the search and browse for the folder where the driver files are located. Click Next.

5. The driver files are installed. Click Finish.

Audiovox PC5750/Pantech PX-500 131

6. When the installation is complete, check from the Device Manager (Start | Control Panel | Phone and Modem Options) that the installation was successful. Under Modems you should see the PANTECH PC Card item.

7. Next, browse to Start | Control Panel | System | Hardware and click on the Device Manager button. Under Modems you should see the PANTECH PC Card item, and under Ports the PANTECH PC Card Diagnostic Serial Port item.



9. In the Device Manager click on Ports. Select the COM port number assigned to the PANTECH PC Card Diagnostic Serial Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.



Pantech UM175 133

PANTECH UM175

1. Unzip the driver files (PANTECH UM175 USB drivers.zip) on your computer.

2. Plug in the data card.

3. Windows will automatically detect the new hardware.

4. Select Install the software automatically (Recommended), and click Next.

5. Select Include this location in the search and browse for the folder where the driver files are located (e.g., C:\Pantech UM175). Click Next.

6. The driver files are installed. Click Finish.


7. Next go to Device Manager. Under Modems you should see the PANTECH UM175 item, and under Ports the PANTECH UM175 Diagnostic Port item.

♦ If you do not see the items mentioned above and instead there are three unknown devices under Others, the driver installation has failed. Right-click each unknown item, select Update Driver Software, and browse to the folder where you unzipped the driver files. After the update, the Pantech items should appear in the Device Manager.

8. Next, set up the dial-up connection manually. Follow instructions on page 6 (for XP) or 9 (for Win 7) then continue from step 9.

9. In the Pantech UM175 Modem Properties dialog, Security page, select No encryption allowed in the Data encryption field. Click OK to close the dialog.

Pantech UM175 135


11. In the Nemo Outdoor Device Configuration dialog, define the following settings (check the port numbers from the Device Manager) and click Apply:

• Trace port: Select the COM port number assigned to PANTECH UM175 Diagnostic Port • Modem port: Select the COM port number assigned to PANTECH UM175 • Packet switched dial-up connection: Select the dial-up connection that you configured

manually, for example, Pantech UM175



PANTECH UML290


1. Browse to folder D:\Drivers\Qualcomm LTE USB Modem on the Nemo Outdoor product CD.

2. Run the VZAM_7.6.3.4_2642j_PantechLTE.exe file to start the installation wizard. If the Windows Security dialog appears, click Run.

3. The device drivers are installed first. After the device drivers are installed, the VZAccess Manager installation is started.


5. Select I accept the terms in the license agreement and click Next.

Pantech UML290 137

6. Click Next and Next. Select Typical in the Setup Type dialog and click Next and Install. Wait until the installation is ready and click Finish.


7. Plug in the USB modem. Windows will automatically detect the new hardware and install drivers. Wait until the installation process is finished.

8. After installation, go to Device Manager. Select Start | Settings | Control Panel | System, open the Hardware tab and click the Device Manager button. You should see the Pantech UML290 item under Modems and the Pantech UML290 Diagnostic Port item under Ports.


Pantech UML290 139

10. In the Device Manager click on Modems. Select the port assigned to Pantech UML290 Diagnostic Port in the Trace Port field in the Device Configuration dialog. Select the port assigned to Pantech UML290 in the Modem Port field.




ZTE MF820T/MF820D

∇ Installing the driver

Connect the device to your computer’s USB port. Windows will detect the new hardware 1.automatically and install the device drivers.

The Mobile Broadband application will be installed next. Click Run Setup.exe and follow the 2.instructions on the screen. Select Yes in the User Account Control dialog if it appears.

♦ When the installation is finished, it is important to close the Mobile Broadband application.

Go to Device Manager. You should see the following items: 3.

• Network adapters: ZTE Mobile Broadband Network Adapter • Ports: ZTE Mobile Broadband AT Port and ZTE Mobile Broadband Diagnostics Port


In the Device Configuration dialog, make the following settings and click Apply: 5.

• Trace Port: Select the port assigned to ZTE Mobile Broadband Diagnostics Port • Modem Port: Select the port assigned to ZTE Mobile Broadband AT Port • Packet switched dial-up connection: Select <NDIS> or the previously made dial-up connection

(see page 6).


ZTE MF668A 141

ZTE MF668A






• Modems: ZTE Proprietary USB Modem • Network adapters: ZTE Wireless Ethernet Adapter • Ports: ZTE Diagnostics Interface and ZTE NMEA Device



• Trace Port: Select the port assigned to ZTE Diagnostics Interface • Modem Port: Select the port assigned to ZTE Proprietary USB Modem • Packet switched dial-up connection: Select <NDIS> or the previously made dial-up connection

(see page 6).



ZTE MF683


Start the driver installation by selecting the correct installation file based on your operating system 1.(..\Drivers\Qualcomm\ZTE\ZTE MF683\USBDriverInstaller_x64.exe or USBDriverInstaller_x86.exe). The installation will run on the background.



• Modems: T-Mobile HSPA+ Modem • Network adapters: T-Mobile Wireless Ethernet Adapter • Ports: T-Mobile Diagnostics Port.



• Trace Port: Select the port assigned to T-Mobile Diagnostics Port • Modem Port: Select the port assigned to T-Mobile HSPA+ Modem • Packet switched dial-up connection: Select <Automatic> or the previously made dial-up

connection (see page 6).


ZTE MF880 143

ZTE MF880






• Modems: ZTE Mobile Broadband Modem • Network adapters: ZTE Mobile Broadband Network Adapter • Ports: ZTE Mobile Broadband Diagnostics Port



• Trace Port: Select the port assigned to ZTE Mobile Broadband Diagnostics Port • Modem Port: Select the port assigned to ZTE Mobile Broadband Modem • Packet switched dial-up connection: Select <NDIS> or the previously made dial-up connection

(see page 6).



ZTE TU25


Make sure that the device is NOT connected to your computer. 1.

The installer executable is named ZTE_Common_API.msi, and it can be found on the installation 2.CD. Click Run to run the installer.

Click Next in the Welcome dialog. 3.

Click Next in the Destination Folder dialog. 4.

Click Install. 5.

Click Continue Anyway. 6.

Finally click Finish. The driver is now installed. Next, plug in the USB device. 7.

Click Continue Anyway until the prompt no longer appears. 8.

Next, browse to Start | Control Panel | System | Hardware and click on the Device Manager 9.button. Under Network adapters you should see the ZTE WiMAX BCM1000 item.

ZTE TU25 145

Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click 10.Phones and select the Beceem BCS200 (524) item. Click Next.

In the Device Manager click on Modems. Select the BECEEM USB in the Trace Port field in the 11.Device Configuration dialog. Leave the Modem Port field empty.




SONY ERICSSON XPERIA ARC S

♦ Please note that currently the Sony Ericsson Xperia arc S driver can be installed on 32-bit Windows 7 only.


Before connecting the Sony Ericsson Xperia Arc S to a computer, make the following settings on 1.the device. Go to Settings | Applications | Development. Deselect USB debugging.

Connect the device to your computer’s USB port. Windows will detect the new hardware 2.automatically.

Open the Device Manager. Under Other devices you will see two SEMC HSUSB Device items. 3.Right-click on the first item and select Update Driver Software.

Select Browse my computer for driver software. 4.

Sony Ericsson Xperia arc S 147

Select Let me pick from a list of device drivers on my computer. 5.

Select Show All Devices and click Next. 6.


Select Have Disk. 7.

Browse to the folder on the Nemo Outdoor product CD where the Sony Ericsson drivers are and 8.click Open.


Click OK. 9.

Select the Sony Ericsson sa0102 Device Modem item and click Next. 10.


Click Yes in the Update Driver Warning message. 11.

Click Close when the installation is finished. 12.


Return to the Device Manager. The Sony Ericsson sa0102 Device Modem item should appear 13.under Modems and there should be one SEMC HSUSB Device item under Other devices.


Again, right-click on the SEMC HSUSB Device item and select Update Driver Software. Repeat 14.steps 3-9.

Select the Sony Ericsson HS-USB Android Diag sa0102 item and click Next. 15.


Click Yes in the Update Driver Warning message and click Close when the installation is finished. 16.

Return to the Device Manager. The Sony Ericsson HS-USB Android Diag sa0102 item should 17.appear under Ports.



Select the port assigned to Sony Ericsson HS-USB Android Diag sa0102 in the Trace Port field in 19.the Device Configuration dialog. Select the port assigned to Sony Ericsson sa0102 Device Modem in the Modem Port field.



ONDA MT689DC 155

ONDA MT689DC

1. Connect the device to your computer’s USB port. Windows will detect the new hardware automatically and start the installation. Click Run AutoRun.exe and follow the instructions on the screen.

2. Select your language and destination folder. By clicking Next, you also accept the license agreement.

3. When the installation is finished, unplug the device from the USB port and restart the computer.

4. Plug the device back to the USB port. Close the AutoPay dialog.

5. If the Chiavetta Internet MT689DC software starts up, close the program.



7. You should see the ONDA Proprietary HS-USB Modem item under Modems and the ONDA HS-USB Diagnostics Interface item under Ports.


9. In the Device Configuration dialog, select the COM port number assigned to ONDA HS-USB Diagnostics Interface item in the Trace Port field. Select the COM port number assigned to the ONDA Proprietary HS-USB Modem item in the Modem Port field.

10. In the Device Configuration dialog, select <Automatic> as the Packet switched dial-up connection. Click Apply.


INDE X 157

APPLICATION TESTER

These dial-up networking setup guidelines apply to any commercial terminal, i.e. a terminal not provided by Anite Finland Ltd, that is used for application testing.

First you need to install the connectivity cable driver. The USB connectivity cable driver and an 22.applicable USB connectivity cable for it will be included in your mobile phone package. Note! Do not connect the USB connectivity cable to your PC until the driver installation is complete! Consult the terminal user manual for instructions on how to install the connectivity cable driver.

After installing the connectivity cable driver, go to Start | Settings | Control Panel | Phone and 23.Modem Options | Modems, and check the Modem port number assigned to the terminal. This port number will be the same as the Modem port in Nemo Outdoor.

Next you need to create a dial-up connection to the Internet for the modem port mentioned above. 24.A dial-up networking installation is required before data transfers can be made. Go to Start | Settings | Control Panel | Network Connections. Check to see if the dial-up connection for your phone was automatically installed with the USB connectivity driver installation. If not, create a new dial-up connection from File | New Connection. The dial-up connection you find in the Network Connections window is the same as the Packet switched dial-up connection in Nemo Outdoor.

When the USB connectivity driver and dial-up networking installations are complete, go to Nemo 25.Outdoor and select Measurement | Add New Device | Phone | Application Tester. In the Device Configuration dialog select the applicable modem port. The Trace port field is grayed out. In the Packet switched dial-up connection field select the created dial-up connection in Start | Settings | Control Panel | Network Connections | Dial-up. Click Apply. If the status field does not say Device is working properly, check to see that you have selected the right port number and try again.

You can also check the earlier chapters in this document for possible similarities to the installation procedures of your terminal.

dial-up networking setup guide 6.41 feb13

Documents

samsung galaxy s

sierra wireless compass

sierra wireless aircard

lg p500h

lg vl600

lg p930

lg vx8350vx8360

lg g7g13g17