device configuration

7/22/2019 Device Configuration

1/3

Device Configuration

Huawei D100/ B200 ZTE MF30

Also applicable to Modem-Router-in-one /E5832 WIFI modem

To proceed with the installation process, refer to the following steps:

a. Insert SBW SIM Card to the device - make sure device is not connected to power supply when inserting the SIMcard

b.For D100 and B200, Plug the cord (220V) and connect the SBW Wi-Fi Router to the CPU through the LAN cable.Press the power button found on the router and wait for PCs Network Connection to connect to the router. ForE5832, simply turn on the modem and connect it to the PC **

c. Open a browser and go tohttp://192.168.1.1/d.Select adminas the user typee.Default password is adminf. Go to Quick Setup and click Nextg.On the configure PPP Profile Settings page:

a.Dial-up number is always *99#b.APN should be Static and type in:

a.mbbandfor Plan 1399b.fbbandfor Plan 899, Plan 799 and Easy Broadbandc. minternetfor Prepaid and SBW Plan 299, 350 and 450d.suntel for Sun DigiHome 999 / SunTel GO 799

c.IP Address is recommended to be set at Dynamicd.Click Next

h.On the configure PPP Dial-up Settings page, leave PPP connection and authentication as default values. ClickNext.

i. On Configure WLAN Settings:a.Name (SSID): User to set-up the router name. This is the name of the router that should appear when

its broadcasting.b.SSID Broadcast - set to Enabled. This turns Wi-Fi broadcasts on. \c. Click Next

j. On Configure WLAN Security:

a.Encryption Mode: Set encryption type to WEPb.Network key will serve as the password to filter access to authorized users. Type in 13-digitalphanumeric characters to set password with WEP as encryption type.

c. Click Nextk. The next page will display the router configuration. Click Finish.

To change the router Master Password (different from network key), follow the steps below:
http://www.suncellular.com.ph/faqs_broadband_device_config.php#huaweid100http://www.suncellular.com.ph/faqs_broadband_device_config.php#huaweid100http://www.suncellular.com.ph/faqs_broadband_device_config.php#ztemf30http://www.suncellular.com.ph/faqs_broadband_device_config.php#ztemf30http://192.168.1.1/http://192.168.1.1/http://192.168.1.1/http://192.168.1.1/http://www.suncellular.com.ph/faqs_broadband_device_config.php#ztemf30http://www.suncellular.com.ph/faqs_broadband_device_config.php#huaweid100


2/3

a.Go to Advance Settings and Click Systemb.Click Modify Passwordc. Type in current passwordd.Type new passworde.Verify new password

To filter users by MAC Addresses, take note of the following steps:

a.Go to Advance Settings and Click WLAN Settingsb.On WLAN MAC Filter page:

a.Set Restriction Mode to Deny or Allowb.Enter MAC Addresses to Block or Allowc. To disable MAC Address Filter, select Disable at Restriction Moded.Click Apply

To select the APN ofHuawei e5832 Pocket WIFI, follow the steps below:

1. Go to a browser and enterhttp://192.168.1.1(Default password is admin)2. Go to Advanced Settings > Dial-up Settings then Connection Settings

3. Click on drop-down to select Profile of Sim card being used.

Note:For Sun Digihome 999 or SunTel Go 799, SunTel profile cant be found on drop-down list of profiles. Pleasemanually edit existing profile name and APN. Go to Advanced Settings then Profile Settings, Edit Profile name and APN(suntel) then click on Save.

Reminder:The default network set up for E5832 is WCDMA Preferred thus 2G Connection or EDGE will be possibly encountered.To avoid this, please follow the procedure below:1. Establish Connection to Huawei E58322. Go to URL 192.168.1.13. User Name: Admin / Password:Admin4. Go to Advanced Settings5. Form Advanced Settings choose Network Settings.6. Then change the Network type to (WCDMA Only), click Apply.

Note: Make sure that you are not currently connected with the network before you configure it because it will causean error.

To proceed with the installation process, refer to the following steps:

a. Insert SBW SIM Card to the device - make sure device is not connected to power supply when inserting the SIMcard

b.Plug the cord and connect the SBW Wi-Fi Router to the CPU through the LAN cable. Press the power button foundon the router and wait for PCs Network Connection to connect to the router.

c. Open a browser and go tohttp://192.168.0.1/d.Select adminas the user typee.Default password is adminf. Go to Quick Setup and click Nextg.On the PPP Profile Configuration page:

a.APN should be Static and type in:a.mbbandfor Plan 1399b.fbbandfor Plan 799, Plan 649 and Easy Broadbandc. minternetfor Prepaid and SBW Plan 350 Lited.suntel for Sun DigiHome 999 / SunTel GO 799

b.Click Next
http://192.168.1.1/http://192.168.1.1/http://192.168.1.1/http://192.168.0.1/http://192.168.0.1/http://192.168.0.1/http://192.168.0.1/http://192.168.1.1/


3/3

h.Leave PPP Authentication Page on default values. Click Next.i. On SSID Configuration Page

b.Name (SSID): User to set-up the router name. This is the name of the router that should appear whenits broadcasting.

c. SSID Broadcast - set to Enabled. This turns Wi-Fi broadcasts on.d.Click Next

j. On Security Configuration Pageb.Encryption Mode: Set encryption type to WEPc. Network key will serve as the password to filter access to authorized users. Type in 13-digit

alphanumeric characters to set password with WEP as encryption type.d.Click Next

k. The next page will display the router configuration. Click Apply.

To change the router Master Password, follow the steps below:

a.Go to Settings and Click Advancedb.Click Managementc. Type in current passwordd.Type new passworde.Verify new passwordf. Click Apply

To filter users by MAC Addresses, refer to the following steps:

a.Go to Settings and Click Firewallb.On MAC/IP/Port Filtering page:

a.Set Restriction Mode to Disable or Enableb.Enter MAC Addresses to Accept or Dropc. To disable MAC Address Filter, select Disable at Restriction Moded.Click Apply

To select APN of Pocket WIFI, take note of the following steps:

1. Go to a browser and enterhttp://192.168.0.1(Default password is admin)2. Go to Settings > 3G Settings then APN Settings3. Click on drop-down to select Profile of Sim card being used.

Note:For Sun Digihome 999 or SunTel Go 799, SunTel profile cant be found on drop-down list of profiles. Pleasemanually add profile name and APN. Go to Settings, then 3G Settings, then APN Setting, Click Add and enter Profilename and APN (suntel) then click on Add.

Reminder:

The default network set up is WCDMA Preferred thus 2G Connection or EDGE will be possibly encountered. To avoidthis, please follow the procedure below:1. Establish Connection2. Go to URL 192.168.0.13. User Name: Admin / Password:Admin4. Go to Settings5. From 3G Settings choose Network Select.6. Then change the Network type to (WCDMA Only), click Apply.

Note: Make sure that you are not currently connected with the network before you configure it because it will causean error.
http://192.168.0.1/http://192.168.0.1/http://192.168.0.1/http://192.168.0.1/

device configuration

Documents