detail booklet stotherm ci xps - sto corp. insulation...detail booklet stotherm ® ci xps series...
TRANSCRIPT
Detail BookletStoTherm® ci XPSSeries 53s.xxSteel Frame ConstructionFebruary 2017
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp.All Rights Reserved.
Structural:
Design structural wall for maximum allowable deflection, normal to the plane of the wall, of L/240. Ultimate tested wind load resistance: +175 psf (8.37 kPa). Apply appropriate safety factor as required by code. Higher ultimate loads can be achieved with adequate stiffness (and sheathing attachment for frame walls) of supporting construction. Refer to Tech Hotline No. 0894-E.
All trim and projecting architectural features must have a minimum 1:2 (27 degree) slope. A minimum of ¾” (19mm) XPS insulation board must remain if areveal is cut in the insulation board. A minimum of 1 ½” thickness of XPS board is needed when a reveal is specified.
Construct a site built mock-up using materials and sub-trades associated with the project to verify installation, sequencing, detailing, and aesthetics.
Fire:
Minimum required thickness of XPS foam plastic insulation board is 1” (25mm). Maximum allowable thickness is 6” (152mm) on types I, II, III, or IV construction. If walls are required to have an hourly fire-resistance rating, the maximum allowable thickness is 2” (51mm) over maximum 2-hour rated nonload bearing frame walls, or 6” over, (concrete or masonry) mass walls. Refer to ICC-ESR 1748 for more information.
XPS insulation board has a service temperature limit of 165°F (74°C). The use of dark colors (Light Reflectance Value of less than 20) is not recommended.
Moisture Protection:
Provide minimum 6” (152mm) clearance above landscaped areas (soil, grass, and other non-paved surfaces), and a minimum of 1” (25.4mm) above finished grade areas, (pavement, patios, sidewalks...) as required by code. StoTherm® ci XPS systems are not intended for use below grade.
Direct incidental moisture to the exterior a maximum of every third floor.
Weep spacing at window, door, floor line and other similar penetrations are to be determined by the Design Professional.
Refer to StoTherm® ci XPS Specifications, Product Bulletins, Technical Hotlines, Sto Installation Manuals, and Maintenance Guides for the most complete andcurrent information. See Tech Hotline Nos. 0403 BSc, 0603 BSc for important information on detailing and moisture control in wall assemblies.
Joints:
Provide minimum ¾” (19mm) wide joints in StoTherm® ci where they exist in the substrate or supporting construction, where the cladding adjoins dissimilar construction or materials, at changes in building height, at expansion, control, and cold joints in construction, and at floor lines in multi-level wood frame construction. Provide minimum of ½” (13mm) wide perimeter sealant joints at all penetrations through the wall (windows, doors, mechanical, electrical, plumbing penetrations, etc...). Specify a compatible backer rod and sealant that has been evaluated in accordance with ASTM C1382 and meets 50%elongation to seal joints and penetration.
Impact Resistance:
For ultra-high-Impact resistance install the Sto Armor Mat Mesh and Sto Mesh, as referenced in the specification, a minimum of 6’-0” (1.8m) above finished grade for areas accessible to pedestrian traffic, as well as areas exposed to abnormal stress or impact. Indicate areas with higher than “Standard” impact resistance on contract drawings.
Codes:
Refer to ICC Evaluation Report ESR No. 1748 for building code compliance information.The final design of the project is ultimately up to the Design Professional. Sto accepts no liability for the design, engineering, or workmanship of any project. The notes provided are in addition to Sto Details, Specifications, and other items provided on the Stocorp.com website.
StoTherm® ci XPSGeneral Notes
Detail No.: 53x.GN
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website. www.stocorp.com
www.stocorp.com
®
Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
StoTherm® ci XPSStoGuard Chart
Detail No.: 53x.SC
The chart below shows the StoGuard family of products, their accompanying fabrics or meshes, as-well-as location and a reference to where they can be applied within the system.
Sto Gold Coat®
StoGuard® FabricSto Gold Coat® TAStoGuard® Mesh
Sto Gold FillStoGuard® Mesh
or Sto Detail Mesh
Sto Guard®
RapidFill™Sto Guard®
TapeSto Guard®
TransitionMembrane
Sto Guard®
RapidSeal
Sheathing orStatic Joints and
Seams inConstruction
Rough Openings
As a Detail Component for Transitions to
Flashing and most Service
Penetrations
Corners
Dynamic & StaticJoints, Seams inConstruction,Transition toFoundation
StoGuard® Products for Transitions, Joint Treatments and Rough Opening Protection.
Refer to the StoTherm® ci XPS Systems Specifications, Details, and Product Bulletins for Additional Information.
Benefits of the StoGuard® Products:
®
Date: January 2017
Sto Gold Coat® – Flexible waterproof air barrier membrane for use in StoTherm® ci XPS Systems. Refer to Sto Tech Hotline No. 1114-BSc for low temperature application.
Sto Gold Coat® TA - Trowel applied air and moisture barrier for use in StoTherm® ci XPS Systems.
Sto Gold Fill –flexible, joint treatment and air barrier material for vertical above grade walls. Applied to rough openings, corners, and sheathing joints in walls with StoGuard Mesh
StoGuard® RapidFill™ - One component air barrier and waterproof material used to seal sheathing joints, seams, cracks, and transitions in above grade wall construction. Rapid drying
time will usually allow for same day installation
StoGuard® RapidSeal – One component air barrier and waterproof material used to protect rough openings. Rapid drying time will usually allow for same day installation of windows
StoGuard® Tape - A self-adhering waterproof air barrier material composed of spun bond polyester fabric laminated to rubberized asphalt adhesive for us on Rough opening protection at
windows, doors, and other openings in wood or metal frame construction.
StoGuard® Transition Membrane – Transitions to flashings and most penetrations. Dynamic and Static Joints, seams in constructions, and transition to foundation.
StoTherm® ci XPSSystem Components
Detail No.: 53s.00Date: January 2017
Notes:
1. StoTherm ci SystemComponents:-StoGuard Air andMoisture Barrier
-Sto Adhesive-XPS Insulation Board-Sto Base Coat-Sto Mesh-Sto Primer (optional)-Sto Finish
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
Sheathing
XPS Insulation Board(See note 2)
Sto MeshSto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Property of Sto Corp. All Rights Reserved.
Sto TurboStickTM Adhesive
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSSystem Components: Ultra-High Impact Resistance
Detail No.: 53s.01Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1.StoTherm ci System Components: - StoGuard Air and Moisture Barrier - Sto Adhesive - XPS Insulation Board - Sto Base Coat - Sto Armor Mat XX - Sto Base Coat - Sto Mesh - Sto Primer (optional) - Sto Finish
3. Ultra-high impact resistance recommended at all ground floors to a minimum height of 6'-0" (1.8 m) above finished grade and other areas accessible to pedestrian traffic, abnormal stress or impact.
1.Sample Notes
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
(with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto TurboStickTM Adhesive
Sheathing
Sto MeshSto Base Coat
Sto Base Coat (with Sto Armor Mat Embedded)
Property of Sto Corp. All Rights Reserved.
XPS InsulationBoard (See note 2)
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSTermination at Grade - Sheathing Flush with Foundation or Slab Edge
Detail No.: 53s.03ADate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Terminate system minimum 6" (15.2 cm) above finished grade, higher for areas with heavy snow accumulations, or where required by code.
3. Ultra-high impact resistance recommended at all ground floors to a minimum height of 6'-0" (1.8 m) above finished grade and other areas accessible to pedestrian traffic, abnormal stress or impact.
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud FramingSto Primer (Optional)
Sto Finish
Sheathing
Terminate Assembly 6" (152 mm) Above Grade, min.
Sto Mesh(with Sto Mesh Embedded) Sto Base Coat
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (Protect with StoCoat Acryl Plus or Flashing)
StoGuard® Air and Moisture Barrier Detail ComponentFlashing, Slopedby Others
Backer Rod & Sealant w/ Weep Holes
Sto TurboStickTM AdhesiveXPS InsulationBoard (See note 2)
Property of Sto Corp. All Rights Reserved.
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSTermination at Grade - Sheathing Overlapping Slab or Foundation
Detail No.: 53s.03BDate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Terminate system minimum 6" (15.2 cm) above finished grade, higher for areas with heavy snow accumulations, or where required by code.
3. Ultra-high impact resistance recommended at all ground floors to a minimum height of 6'-0" (1.8 m) above finished grade and other areas accessible to pedestrian traffic, abnormal stress or impact.
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud FramingSto Primer (Optional)
Sto Finish
Sheathing
Sto Mesh(with Sto Mesh Embedded) Sto Base Coat
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (Protect with StoCoat Acryl Plus or Flashing)
StoGuard® Air and Moisture Barrier Detail Component
Flashing, Slopedby Others
Backer Rod & Sealant w/ Weep Holes
Sto TurboStickTM Adhesive
XPS Insulation Board (See note 2)
Property of Sto Corp. All Rights Reserved.
Terminate Assembly 6" (152 mm) Above Grade, min.
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSAesthetic Feature Band
Detail No.: 53s.04Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Feature band attached with Sto TurboStick Adhesive, also used as filler and rasped smooth at any gaps between feature band and base layer of insulation board.
2. Slope top surface of feature band minimum 27 degrees. Increase slope for northern climates to prevent snow and ice accuulations.
3. Limit thickness of build-out to reduce maintenance associated with projecting architectural features.
StoGuard® Air and Moisture Barrier
Sheathing
Sto Base Coat (with Sto Mesh Embedded)
StoGuard® Air and Moisture Barrier
Sheathing
(with Sto Mesh Embedded) Sto Base Coat
Sto Flexyl or Sto Watertight Coat (with Sto Mesh or Sto Detail Mesh Embedded); Return Vertically 4" (102 mm) min. Above and Below Feature Band
Sto Mesh
Sto Mesh
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
XPS InsulationBoard (See note 4)
Sto TurboStickTM Adhesive
Sto Primer (Optional)
Sto Finish
Sto Finish
Sto Primer (Required over Sto Flexyl, Sto Watertight Coat, and Sto Base Coat Above and Below)
Thin Build-Out
Thick Build-Out
Thick Build-Out, 2-4 in. (51-102 mm)
Thin Build-Out,
≤ 2 in. (51 mm)
XPS InsulationBoard (See note 4)
4. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSAesthetic Reveal
Detail No.: 53s.05Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Slope bottom surface of reveal minimum 27 degrees. Increase slope for northern climates to prevent snow and ice accumulations.
2. Maintain minimum 3/4 inch (19 mm) thickness of insulation board at base of reveal.
Sto Primer (Optional)
Sto FinishSto Base Coat (with Sto Detail Mesh Embedded)
3/4" (19 mm) min.
2 1/2" (64 mm) min. Ovelap of Sto Detail Mesh w/ Sto Mesh @ Top and Bottom of Reveal
StoGuard® Air and Moisture Barrier
Sto Base Coat (with Sto Mesh Embedded) Sto Mesh
Sto Primer (Optional)
Sto Finish
3/4" (19 mm) min.
StoGuard® Air and Moisture Barrier
Sto Base Coat (with Sto Mesh Embedded) Sto Mesh
Sheathing
Sheathing
Sto TurboStickTM Adhesive
XPS InsulationBoard (See note 3)
Property of Sto Corp. All Rights Reserved.
Sto TurboStickTM Adhesive
XPS InsulationBoard (See note 3)
Sto Detail Mesh
Option 1 with Sto Detail Mesh
Option 2 with Continuous Sto Mesh
3. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSReceptor-Type Window Sill
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.23A-1Date: January 2017
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
Blocking
StoGuard® Air and Moisture Barrier Rough Opening Protection
Step 1 - Rough Opening Protection
StoGuard® Air and Moisture Barrier Rough Opening Protection Over Blocking
StoTherm® ci XPSReceptor-Type Window Sill
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.23A-2Date: January 2017
Sto TurboStickTM Adhesive
XPS Insulation Board(See note 2)
Property of Sto Corp. All Rights Reserved.
XPS Insulation Board (See note 2), Pre-Wrapped
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
End Dam Set in Sealant
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto TurboStick Adhesive (Fill Gap Between EPS Boards at Corner with this Adhesive, Cut Flush with Surface and Rasp Smooth)
Sill Receptor w/ Weep Holes (Sill Flashing Extender Not Shown for Clarity)
Weep Holes
Angle (As Needed for Attachment of Sill Receptor and Support)
StoGuard® Air and Moisture Barrier Rough Opening Protection
Blocking
Step 2 - Receptor with End Dam
StoTherm® ci XPSReceptor-Type Window Sill
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.23A-3Date: January 2017
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
XPS Insulation Board (See note 2), Pre-Wrapped around Rough Opening
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded)
Sto Base Coat
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
XPS Insulation Board (See note 2) Pre-Wrapped at Jamb
Sill Receptor w/ Weep Holes
Spray Polyurethane Foam Insulation
Jamb Receptor
Sill Extender w/ Continuous Bead of Sealant @ Bottom
Window Assembly
Angle (As Needed for Attachment of Sill Receptor and Support)
StoGuard® Air and Moisture Barrier Rough Opening Protection
Blocking
Step 3 - Window and Sill Flashing, Cladding, and Perimeter Weather and Air Seals
Air Seal, Backer Rod & Sealant (Air Seal Entire Perimeter)
Backer Rod & Sealant (Entire Perimeter)
StoTherm® ci XPSReceptor-Type Window Head
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.23B-1Date: January 2017
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Cement Board Filler or Other TrimFlashing by Others
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier Detail Component
Step 1 - Rough Opening Protection, Head Flashing
StoTherm® ci XPSReceptor-Type Window Head
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.23B-2Date: January 2017
Property of Sto Corp. All Rights Reserved.
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
XPS Insulation Board (See note 2), Pre-Wrapped
XPS Insulation Board(See note 2)
Window Assembly
Spray Polyurethane Foam Insulation
Head Receptor
Jamb Receptor
Cement Board Filler or Other TrimFlashing by Others
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Air and Moisture Barrier
Sto TurboStickTM Adhesive
Step 2 - Receptor and Window
Sto TurboStick Adhesive (Fill Gap Between XPS Boards at Corner with this Adhesive, Cut Flush with Surface and Rasp Smooth, Reinforce Top Corner with Sto Mesh or Sto Detail Mesh Embedded in Base Coat)
StoTherm® ci XPSReceptor-Type Window Head
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.23B-3Date: January 2017
Property of Sto Corp. All Rights Reserved.
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto TurboStick Adhesive (Fill Gap Between EPS Boards at Corner with this Adhesive, Cut Flush with Surface and Rasp Smooth)
XPS Insulation Board (See note 2), Pre-Wrapped around Rough Opening
Sto TurboStickTM Adhesive
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded)
Sto Base Coat
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Air and Moisture Barrier
Spray Polyurethane Foam Insulation
XPS Insulation Board (See note 2), Pre-Wrapped
Step 3 - Cladding and Perimeter Weather and Air Seals
Window Assembly
Air Seal, Backer Rod and Sealant (Air Seal Entire Perimeter)
Head Receptor
Jamb Receptor
Backer Rod & Sealant (Entire Perimeter, with Weeps at Head)
Cement Board Filler or Other Trim (Finish Cement Bd. w/ StoCoat Acryl Plus)
Flashing by Others
StoTherm® ci XPSFlanged Window-Sill
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.24A-1Date: January 2017
Property of Sto Corp. All Rights Reserved.
Step 1 - Rough Opening Protection, Sill Flashing
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
1/8" (3 mm) Thick Washers Behind Mounting Flange
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Detail Component
Flashingby Others
Slope
StoTherm® ci XPSFlanged Window-Sill
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.24A-2Date: January 2017
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
Step 2 - Window and Trim
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
XPS Insulation Board (See note 2)
Spray Polyurethane Foam Insulation
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sealant Behind Mounting Flange (Jambs and Head Only)
StoGuard® Detail Component
Flashingby Others
Slope
Window Assembly
1/8" (3 mm) Thick Washers Behind Mounting Flange
Spray Polyurethane Foam Insulation
StoTherm® ci XPSFlanged Window-Sill
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.24A-3Date: January 2017
Sto TurboStickTM Adhesive
XPS Insulation Board (See note 2)
Property of Sto Corp. All Rights Reserved.
XPS Insulation Board (See note 2)
Step 3 - Cladding and Perimeter Weather and Air Seals
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded)
Sto Base Coat
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Spray Polyurethane Foam Insulation
Window Assembly
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Detail ComponentFillet Bead of Sealant (not
shown) Between Underside of Flashing and Base Coat
1/8" (3 mm) Thick Washers Behind Mounting Flange
Sealant Behind Mounting Flange (Jambs and Head Only)
Spray Polyurethane Foam Insulation
Backer Rod & Sealant with Weeps Between Trim and Flashing Leg
Flashing by Others
Backer Rod & Sealant (Entire Perimeter)
Air Seal, Backer Rod & Sealant (Air Seal Entire Perimeter)
Air Seal, Backer Rod & Sealant (Air Seal Entire Perimeter)
StoTherm® ci XPSFlanged Window-Head
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.24B-1Date: January 2017
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Window Assembly
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Detail Component
Sealant Behind Mounting Flange (Jambs and Head Only)
Flashing by Others
Sealant
Property of Sto Corp. All Rights Reserved.
Step 1 - Rough Opening Protection, Head Flashing
StoTherm® ci XPSFlanged Window-Head
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.24B-2Date: January 2017
Sto TurboStickTM Adhesive
XPS Insulation Board (See note 2), Pre-Wrapped Around Opening
Property of Sto Corp. All Rights Reserved.
Step 2 - Window and Trim
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
XPS Insulation Board (See note 2)
Window Assembly
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Detail Component
Sealant Behind Mounting Flange (Jambs and Head Only)
Sealant
Spray Polyurethane Foam Insulation
Flashing by Others
Spray Polyurethane Foam Insulation
Backer Rod & Sealant Weather and Air Seals (Entire Perimeter with Weeps Between Underside of Trim & Flashing Leg)
StoTherm® ci XPSFlanged Window-Head
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Consult with window and sealant manufacturers to verify window installation and detailing and to assure no water leakage into the wall assembly. Consult with window manufacturer regarding window and/or flashing assembly thermal breaks to avoid condensation. Test the final assembly using materials and trades associated with the project to verify performance. Correct any deficiencies associated with excess air leakage, water infiltration into the wall assembly, or structural inadequacies.
Detail No.: 53s.24B-3Date: January 2017
Sto TurboStickTM Adhesive
XPS Insulation Board (See note 2), Pre-Wrapped Around Opening
Property of Sto Corp. All Rights Reserved.
Step 3 - Cladding and Perimeter Weather and Air Seals
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded)
Sto Base Coat
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
XPS Insulation Board(See note 2)
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Detail Component
Sealant Behind Mounting Flange (Jambs and Head Only)
Sealant
Spray Polyurethane Foam Insulation
Flashing by Others
Spray Polyurethane Foam Insulation
Window Assembly
Backer Rod & Sealant Weather and Air Seals (Entire Perimeter with Weeps Between Underside of Trim & Flashing Leg)
StoTherm® ci XPSSoffit: Insulated and Unvented
Detail No.: 53s.30Date: Jauary 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Continue StoGuard air and moisture barrier onto dissimilar material or construction where required after verifying substrate material compatibility. Refer to Sto Detail 53s.53 for typical detailing of inside corner if substrate material or construction is dissimilar. Refer to Sto Detail 53s.54A if substrate material is similar at inside corner.
2. 4" (10 cm) thick insulation board typically required for proper lap of accessory with mesh "tail." For thinner sections of insulation board pre-wrap insulation board with Sto base coat and mesh.
3. Multi-story buildings where construction is required to be Noncombustible may require special examination of soffit conditions with foam plastic insulation. Verify with professional fire protection engineer and building code official.
Nominal 1/4 inch (6 mm) Gap for Drainage
Sheathing
Sto Base Coat (with Sto Mesh Embedded) Sto MeshStoGuard® Joint Treatment
Backer Rod and Sealant
Structure
Sto Drip Edge Profile
Sto Drip Edge Profile (See Drawing Below) Dissimilar Material or
Wall Construction
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Sto TurboStickTM Adhesive
XPS Insulation Board(See note 4)
Property of Sto Corp. All Rights Reserved.
4. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSSoffit: Uninsulated and Vented
Detail No.: 53s.31Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Prevent "communication" of vented air space with conditioned interior air to reduce the likelihood of condensation on materials in the vented space.
2. Typical soffit board is gypsum sheathing in compliance with ASTM C 1177. Refer to Sto Specification No. F601S and Sto Detail Series 14.xx.
Nominal 1/4 inch (6 mm) Gap for Drainage
Sheathing
Sto Base Coat (with Sto Mesh Embedded) Sto Mesh
Backer Rod and Sealant
Structure
Sto Drip Edge Profile
Sto Drip Edge Profile (See Drawing Below) Dissimilar Material or
Wall Construction
Light Gauge Steel Stud FramingStoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
StoGuard® Joint Treatment
Soffit Vent
Casing Bead
Sto TurboStickTM Adhesive
XPS Insulation Board(See note 3)
Property of Sto Corp. All Rights Reserved.
3. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSFloor Line Without Deflection
Detail No.: 53s.40Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. This detail is typically limited to low-rise construction where no floor line deflection is anticipated. Refer to Sto Details 53s.41A, and 53s.41B for a floor line condition with deflection.
2. Sheathing attachment is typically at 8" (20.3 cm) on center or less vertically. Add C-channels or other attachment means along slab edge if necessary to conform with required fastener spacing.
3. Provide fire stopping at floor line as needed.
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Sheathing
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
Structure
Sto TurboStickTM Adhesive
XPS Insulation Board(See note 4)
Property of Sto Corp. All Rights Reserved.
4. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSFloor Line With Deflection -Concealed Flashing and Drainage at Floor Line
Detail No.: 53s.41ADate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Sheathing attachment is typically at 8" (20.3 cm) on center or less vertically. Add C-channels or other attachment means along slab edge if necessary to conform with required fastener spacing.
2. Provide fire stopping at floor line as needed.
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Sheathing
XPS Insulation Board(See note 3)
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
StoGuard® Transition Membrane
Horizontal Deflection Joint: Backer Rod & Sealant w/ Weeps. Sealant Applied to Base Coat as per Sealant Manuf'r Instructions
Slotted Deflection Track
Backer Rod
Structure
StoGuard® Transition Membrane Applied from Face of StoGuard® Air & Moisture Barrier and Lapped onto Top of EPS Insulation Board with Slight Slope for Drainage @ Bottom of Joint
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
3. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSFloor Line With Deflection - No Drainage at Floor Line
Detail No.: 53s.41BDate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Sheathing attachment is typically at 8" (20.3 cm) on center or less vertically. Add C-channels or other attachment means along slab edge if necessary to conform with required fastener spacing.
2. Provide fire stopping at floor line as needed.
3. Provide drainage at floor lines as deemed by design professional, typically no more than every third floor line. Refer to Sto Detail 53s.41A.
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Sheathing
XPS Insulation Board(See note 4)
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
StoGuard® Transition Membrane
Horizontal Deflection Joint: Backer Rod & Sealant. Sealant Applied to Base Coat as per Sealant Manuf'r Instructions
Slotted Deflection Track
Backer Rod
Structure
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
4. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Detail applies to Balcony Protected Overhead by Balcony Ceiling Above.
2. Slope balcony to direct water away from wall.
3. Consider the use of high or ultra-high reinforcing meshes on balcony walls to supplement standard reinforcing mesh for added abuse and impact resistance.
4. Verify compatibility of StoGuard Air and Moisture Barrier with balcony waterproof membrane material where they interface or lap one another.
5. Counter flash balcony membrane on wall if not fluid applied.
Detail No.: 53s.42ADate: January 2017
StoTherm® ci XPSBalcony Floor/Wall
Sto TurboStickTM Adhesive
XPS Insulation Board(See note 6)
Property of Sto Corp. All Rights Reserved.
6. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded) Sto Base Coat
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
Balcony Slab Recess
Backer Rod & Sealant w/ Weeps
Balcony Waterproof Membrane and Finished Flooring
Balcony
Cant and Air Seal Transition Material
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Detail applies to Balcony Protected by Balcony Ceiling Above.
2. Underside of balcony may also be finished with Sto Finish or other Sto smooth or textured coatings.
Detail No.: 53s.42BDate: January 2017
StoTherm® ci XPSBalcony Ceiling/Wall
Sto TurboStickTM Adhesive
XPS Insulation Board(See note 3)
Property of Sto Corp. All Rights Reserved.
3. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
(with Sto Mesh Embedded) Sto Base Coat
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
Sto Mesh
Backer Rod
Backer Rod and Sealant
Balcony
Slotted Deflection Track
Skim Coat of Sto Base Coat
Sto Primer Smooth
StoCoat Acryl Plus
StoTherm® ci XPSHorizontal Termination at Dissimilar Cladding
Detail No.: 53s.50Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
XPS Insulation Board(See note 1)
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Light Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
Backer Rod and Sealant with Weep Holes
Sheathing
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier Detail Component
Wood Blocking
Brick Cavity Wall
Masonry Sill
Flashing by others
StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
Sealant
1. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSVertical Termination at Dissimilar Cladding
Detail No.: 53s.51ADate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
Sheathing
XPS Insulation Board(See note 1)
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Masonry Veneer or Other Dissimilar Material
Sealant and Backer Rod
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
1. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSVertical Termination at Dissimilar Backup Wall Construction
Detail No.: 53s.51BDate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier Sheathing
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier (Minimum Two Coats on CMU Wall Surface)
CMU Backup
Masonry Veneer or Other Dissimilar Material
Sto Finish
Sealant and Backer Rod
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Primer (Optional)
XPS Insulation Board(See note 1)
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
1. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSVertical Expansion Joint in Back-Up Wall
Detail No.: 53s.52ADate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
Sheathing
XPS Insulation Board(See note 1)
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sealant and Backer Rod
Sto Finish
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
1. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSVertical Expansion Joint in Back-Up Wall,StoTherm ci and Dissimilar Cladding
Detail No.: 53s.52BDate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
.
XPS Insulation Board (See note 1)
Masonry Veneer or Other Dissimilar Material
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier
Sheathing
Sto Primer (Optional)
Sto Base Coat (with Sto Mesh Embedded) Sto Mesh
Sto Finish
Sealant and Backer Rod
Light Gauge Steel Stud Framing
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
1. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSInside Corner with Dissimilar Backup Wall
Detail No.: 53s.53Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
XPS Insulation Board(See note 1)
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture BarrierLight Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
Sealant and Backer Rod
StoGuard® Air and Moisture Barrier (Minimum Two Coats on CMU Wall Surface)
CMU Backup
Sheathing
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
1. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSInside and Outside Corner with Common Substrateand Sto Mesh Reinforcement
Detail No.: 53s.54BDate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Provide joint at interior corner if movement is anticipated. Refer to Sto Detail 53s.53.
Sto Base Coat (with Sto Mesh Embedded)
StoGuard® Joint Treatment
Light Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
StoGuard® Air and Moisture Barrier
Sheathing
Return Sto Mesh 6 in. min. Around Corner
Return Sto Mesh 6 in. min. @ Inside Corner
Sto Mesh
Sto TurboStickTM Adhesive
XPS InsulationBoard (See note 2)
Property of Sto Corp. All Rights Reserved.
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSTermination at Parapet - Front
Detail No.: 53s.60ADate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
XPS Insulation Board(See note 1)
Sto Base Coat (with Sto Mesh Embedded)
Metal Coping
Light Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
StoGuard® Air and Moisture Barrier
Sheathing
Roof Structure
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (or Compatible Roofing Membrane)
Wood Blocking
StoGuard® Detail Component
Sto Mesh
Backer Rod & Sealant
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
1. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSTermination at Parapet - Back
Detail No.: 53s.60BDate: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
XPS Insulation Board(See note 1)
Sto Base Coat (with Sto Mesh Embedded)
Metal Coping
Roof Membrane
Sto Primer (Optional)
StoGuard® Air and Moisture Barrier Detail Component
Sheathing
Roof Structure
Backer Rod and Sealant
Sto MeshTermination Bar for Roof Membrane
Light Ga. Steel Stud Framing
Cover BoardRoof Insulation
StoGuard® Air and Moisture Barrier
Termination Bar for Roof Membrane
XPS Insulation Board(See note 1)
Wood Blocking
StoGuard® Detail Component
Insulation
Z-Flashingby Others
Roof Membrane
StoGuard® Air and Moisture Barrier
Sheathing
Backer Rod and Sealant with Weep Holes
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (or Compatible Roofing Membrane)
Wood BlockingStoGuard® Detail Component
Sto Finish
1. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSParapet with Cornice Feature
Detail No.: 53s.61Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Cornice feature limited to 6 1/2" (16.5 cm) maximum thickness, including base layer of insulation, for noncombustible type construction. Special analysis with regard to fire propagation may enable thicker sections. Thicker sections permitted within practical limits for combustible construction.
2. Cornice feature attached with Sto TurboStick Adhesive; also used as filler and rasped smooth at any gaps between feature band and base layer of insulation board.
3. Cornice feature may also be attached directly to StoGuard where applicable.
4. Supplemental mechanical attachment of feature band maybe necessary in some cases. Verify installation method for adequate attachment before commencing work.
View of Mesh Overlap
Sto Mesh Embedded in Base Coat Laps Sto Mesh on Cornice 2 1/2 in. (64 mm) min.
XPS Insulation Board(See note 5)
Cornice Feature Pre-Wrapped with Sto Base Coat (with Sto Mesh Embedded)
Wood Construction as Required StoGuard® Air and Moisture Barrier Sheathing Joint Treatment Extends 2 in. (51 mm) min. at Vertical and Horizontal Surfaces
XPS InsulationBoard (Seenote 5)Sto Base Coat (with
Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Backer Rod and Sealant
Sto Mesh
Light Gauge Steel Stud Framing
1/2 in. (13 mm) min. Gap Between Top Surface of Cornice Feature and Underside of Wood ConstructionPre-Wrapped
Cornice
Property of Sto Corp. All Rights Reserved.
View of Pre-Wrapped Cornice
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (or Compatible Roofing Membrane)
Metal Coping
StoGuard® Air and Moisture Barrier
Sheathing
5. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSSaddle Flashing at Lower/Higher Wall Abutment
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Provide minimum 2" (51mm) gap between parapet cap flashing and StoTherm ci termination.
Sheathing
Detail No.: 53s.64-1Date: April 2016
StoGuard® Detail Component
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Property of Sto Corp. All Rights Reserved.
Step 1 - Air and Moisture Barrier
StoTherm® ci XPSSaddle Flashing at Lower/Higher Wall Abutment
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Provide minimum 2" (51mm) gap between parapet cap flashing and StoTherm ci termination.
Detail No.: 53s.64-2Date: April 2016
A
BC
StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier
Assembled Saddle Flashing
Saddle Flashing Components
Property of Sto Corp. All Rights Reserved.
Step 2 - Saddle Flashing
StoTherm® ci XPSSaddle Flashing at Lower/Higher Wall Abutment
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Provide minimum 2" (51mm) gap between parapet cap flashing and StoTherm ci termination.
Detail No.: 53s.64-3Date: January 2017
Parapet Cap Flashing Assembly Extends to Perpendicular Wall
Light Gauge Steel Stud Framing
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (or Compatible Roofing Membrane)
StoGuard® Detail Component
Wood Blocking
Saddle Flashing Assembly
Backer Rod & Sealant Between StoTherm ci and Saddle Flashing Assembly
StoGuard® Air and Moisture Barrier
XPS Insulation Board(See note 2)
StoTherm ci Assembly
Property of Sto Corp. All Rights Reserved.
Step 3 - Cladding, Coping, and Sealant
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSScupper Penetration
Detail No.: 53s.65Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
StoGuard® Air and Moisture Barrier
XPS Insulation Board(See note 1)
Sto Base Coat (with Sto Mesh Embedded) Sto Primer (Optional)
Sto Finish
Sto Mesh
Light Gauge Steel Stud Framing
Sheathing
Wood Blocking
Roof Membrane
Roof Insulation
Roof Structure
Backer Rod & Sealant
StoGuard® Air and Moisture Barrier Detail Component
Scupper Assembly
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
1. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Refer to Sto Detail 53s.70B where sheathing is "rough cut" around pipe or where gap around pipe exceeds allowable gap dimension for StoGuard Air and Moisture Barrier Detail Component.
StoGuard® Air and Moisture Barrier
XPS Insulation Board(See note 2)
Sto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Mesh
Light Gauge Steel Stud Framing
Sheathing
Backer Rod & Sealant
StoGuard® Air and Moisture Barrier Detail Component
Pipe
Detail No.: 53s.70ADate: January 2017
StoTherm® ci XPSPipe Penetration - Precision Cut Sheathing
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Appropriate spray foam is used to fill gaps in sheathing. Where sheathing fits snug around pipe refer to Sto Detail 53s.70A.
Retrofit or Oversized Pipe Penetration Opening
Detail No.: 53s.70BDate: January 2017
StoTherm® ci XPSPipe Penetration - Rough Cut Sheathing
StoGuard® Air and Moisture Barrier
XPS Insulation Board(See note 2)
Sto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Mesh
Light Gauge Steel Stud Framing Sheathing
Backer Rod & Sealant
StoGuard® Air and Moisture Barrier Detail Component
Pipe
Spray Foam (to Fill Gaps, Shaved or Rasped Flush with Sheathing Surface)
Sto TurboStickTM Adhesive
Property of Sto Corp. All Rights Reserved.
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene
StoTherm® ci XPSSign Attachment
Detail No.: 53s.71Date: January 2017
IMPORTANT: Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install Sto products. Refer to project specific contract documents.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Notes:
1. Blocking not required where solid substrate or wood-based sheathing is capable of supporting the sign (or other attached object). Use appropriate fasteners for attachment.
StoGuard® Air and Moisture Barrier
Sto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Mesh
Light Gauge Steel Stud Framing
Sheathing
Wood Blocking
Hole Drilled in EIFS and Lined with Sealant
PVC or Stainless Steel Sleeve (Sleeve Extends From Finish Through Blocking, Shown Partial Length for Clarity)
Neutral Cure Sealant
Sign
Washer Behind Sign Set in Sealant
Bolt w/ Washers at Each End
Sto TurboStickTM Adhesive
XPS Insulation Board(See note 2)
Property of Sto Corp. All Rights Reserved.
2. XPS insulation options:-Owens Corning Foamular®
CI-C Extruded Polystyrene -Dow STYROFOAMTM Panel Core 20 Extruded Polystyrene