crutchfield tb radio

8/11/2019 Crutchfield TB Radio

http://slidepdf.com/reader/full/crutchfield-tb-radio 1/5

2 Factory Radio Removal ✔ ✔

3 Receiver Installation ✔4 Front Door Speakers ✔ ✔

5 Rear Door Speakers ✔ ✔ ✔

TM

Inside...

Tools Required

012 0150Revision 06/13/06

2002-

Chevrolet Trailblazer

▲

Page

Phillips

Screwdriver

Small Flat Blade

Screwdriver

Panel Tool

Socket, Ratchet,& Extension

*0000120150*

T-15 Torx Driver

✔✔

✔

7mm 10mm

✔

Note: At this time, no aftermarket antenna is available for this vehicle.

A replacement antenna may be purchased from a Chevrolet dealership.

IM PORTANT

Before starting, compare items on your invoice with items received.Carefully check through packaging material. If any item is missing,please call Crutchfield Technical Service at 1-800-955-9094.

Although reasonable attempts are made to verify the accuracy of the information contained in this MasterSheet, it is presented withoutwarranties or guarantees of any type due to the constantly changing nature of this type of information and running changes in vehicleproduction. Any person or entity using this information does so at his or its own risk. If you find our instructions are different from yourvehicle, or if you have questions, do not continue with your installation. Contact our toll-free technical support for assistance.

®

Copyright 2006 Crutchfield Corporation

R

R



012 0150

Factory Radio Removal

2

Dash Trimpanel

1. Set parking brake and disconnectnegative battery cable to prevent

any electrical short.

2. Remove two (2) 7mm screws from driver’s

knee panel. Pry out top edge of panel to releaseretaining clips and allow panel to hang.

3. Remove three phillips screws from bottom ofdash trimpanel exposed by lowering of knee

panel. Remove two (2) phillips screws from dashtrimpanel located above instrument cluster.

4. Place gear shift into lowest position.

5. Remove one (1) phillips screw from dash

trimpanel located to the left side of cigarettelighter.

6. Place steering wheel in lowest position.

7. Carefully pry around all edges of dash trimpanel to release six (6)

metal retaining clips. Disconnect all wiring harnesses and work dashtrimpanel over steering column to remove panel.

8. Remove three (3) 7mm screws securing factory radio. Pull out radio,

disconnect and remove.

1-800-955-9094

Technical Service

Factory Radio

Instrument Cluster

Driver’s Knee Panel

✔ Return gear shift to park position.

SAFETY CHECK

®


R

R



012 0150

Receiver Installation

3

Bend tabs after sleeve

is inside mounting bracket.

FIGURE 1

FIGURE 2

DIN Sleeve

1-800-955-9094

Technical Service

1. Secure receiver mounting bracket to dash with

screws previously removed from factory radio.Insert spacer in mounting bracket.

2. Remove DIN sleeve from receiver (Figure 1).

3. Make wiring connections following instructionssupplied with interface purchased from Crutchfield.

4. Slide DIN sleeve into mounting bracket andsecure to bracket by bending the securing tabs

(Figure 2).

5. Hold receiver near dash. Connect interface andplug antenna lead into rear of receiver.

6. Slide receiver fully into sleeve and testoperation.

7. Reassemble dash by reversing disassembly steps.

8. If not installing an equalizer, snap in EQ coverplate.

Receiver Mounting Bracket

Spacer

EQ Cover Plate

Securing Tabs

Certain warning chimes in your vehicle may

be disabled by installation of an aftermarket receiver. You must use the recommended

Crutchfield integration adaptor to retain the warning chimes. Failure to do so may result in serious injury or death.

IMPORTANT SAFETY WARNING: !

✔ Return gear shift to park position.

SAFETY CHECK

®


R

R

crutchfield tb radio

Documents