TOYOTA SIENNA 2013 - BODY SIDE MOLDING

Kit Contents Item # Quantity Reqd. Description 1 1 Body Side Molding

Hardware Bag Contents Item # Quantity Reqd. Description

Additional Items Required For Installation Item # Quantity Reqd. Description 1 None

ConflictsNote:

Recommended Tools Safety Tools Safety Glasses

Special ToolsMagnetic Straight Edge

Installation ToolsWiping Cloth Non-Scratch, Lint Free Grease Pencil Tape Measure Molding Roller or Presser

Special ChemicalsCleaner Isopropyl Alcohol-Based Water 50:50

Color Applicability/Trim Level

Acc essoryC ol or 00016-08001-01

00016-08001-02

00016-08001-03

00016-08001-04

00016-08001-06

000 16-08001-10

00016-08001- 11

00016- 08001-20Vehicle/Trim Color Silver Sky Metallic (1D6) X

Black (202) X

Salsa Red Pearl (3R3) X Sandy Beach Metallic (4T8) X

Cypress Pearl (6T7) X

Shoreline Blue Pearl (8V5) X

Super White (040) X

Predawn Gray Mica (1H1) X

Blizzard Pearl (070) X

General Applicability Note: Sienna Models 2012

Recommended Sequence of Application Item # Accessory 1 Paint Protection 2 Body Side Molding

*Mandatory

SPECIAL NOTE:After TMS and Safety mandated preparatory steps have been taken, the installation sequence is the suggested method for completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessory installation. Unless otherwise stated in the document, the associates may perform the installation steps in any order to make the installation as efficient as possible while maintaining consistent quality.

Part Number: 00016-08001Accessory Code: MW30

Southeast Toyota Distributors, LLC Page 1 of 4

00016-08001-08

iustyfaStamp

iustyfaText BoxDoc. 12.92.00 PIO / DIO Rev. A 02/11/13

IUSTYFALine

IUSTYFALine

TOYOTA SIENNA BODY SIDE MOLDING

Care must be taken while installing this accessory to ensure damage does not occur to the vehicle. Use approved guidelines to insure a quality installation.

These guidelines can be found in the “Accessory Installation Practices” document.

A. Installation Preparation

1. Verify that the part is for the correct vehicle model and that it fits the vehicle properly.

2. During installation, the vehicle, the part, and the tape MUST be between 60° and 110° F for proper adhesion. Failure to maintain proper installation procedure may result in the part not functioning correctly.

3. Inspect the vehicle and parts for damage prior to installing the Body Side Molding.

i. Paint: Prepare part surfaces per Toyota paint standards. Do not use lacquer thinner or enamel reducer as a degreaser.

4. Make sure that all Body Side Molding installation surfaces are free of dirt and/or grease. (Fig. A1)

i. Use a clean, lint-free cloth and isopropyl alcohol-based cleaner.

B. Installation

1. From the bottom of the front door, perpendicular with the front jack arrow on the vehicle rocker, measure up 14-1/2" and mark vehicle with a grease pencil. (Fig. B1)

2. From the bottom of the rear door, perpendicular with the rear jack arrow on the vehicle rocker, measure up 15" and mark vehicle with a grease pencil. (Fig. B2)

Fig. A1

Fig. B1

Mark

Jack Arrow

Fig. B2

Mark

Jack Arrow

Fig. B3

Mark

Center Door Seam

Southeast Toyota Distributors, LLC Page 2 of 4

TOYOTA SIENNA BODY SIDE MOLDING

3. From the bottom of the rear door, at the center door seam on the vehicle rocker, measure up 14-7/8" and mark vehicle with a grease pencil. (Fig. B3)

4. Using marks made in Steps 1, 2, and 3, place magnetic straight edge under marks on vehicle. (Fig. B4)

5. Install Body Side Molding using magnetic straight edge applied in Step 4 as a guide. (Fig. B5)

6. Install Body Side Molding approximately 1/8" from front and rear door edge respectively. (Fig. B6)

NOTE: Orientation of left side and right side pieces is critical.

i. The front Body Side Molding piece is beveled on the top. (Fig. B7)

ii. The end of the rear Body Side Molding piece is angled parallel with the door seam. (Fig. B8)

7. Apply firm pressure with roller or presser to the taped areas for proper bond. Tape reaches maximum adhesive bond after 24 hours of contact.

Fig. B5

Fig. B7 Fig. B8

Fig. B4

Magnetic Straight Edge Below Marks

Southeast Toyota Distributors, LLC Page 3 of 4

Fig. B6

TOYOTA SIENNA BODY SIDE MOLDING

Checklist: these points MUST be checked to insure a quality installation.

Check:

Accessory Function Check

Check visual alignment

No gap is allowed between the tape and the vehicle door surface

Vehicle function checks

Look For:

Molding should be straight

No gap is allowed between the tape and the vehicle door surface

Open and close both rear doors to ensure the molding does not rub or hit door frame.

Vehicle Function Checks: Part Number List:

Part Number Color Code00016-08001-01 Silver Sky Metallic 1D6 00016-08001-02 Black 202 00016-08001-03 Salsa Red Pearl 3Q3 00016-08001-04 Sandy Beach Metallic 4T8 00016-08001-06 Cypress Pearl 6T7 00016-08001-07 Mistic Teal Mica 785 00016-08001-10 Super White 040 00016-08001-11 Predawn Gray Mica 1H1 00016-08001-20 Blizzard Pearl 070

Right Side Replacement Color Code00016-08001-30 Super White 040 00016-08001-31 Blizzard Pearl 070 00016-08001-32 Silver Sky Metallic 1D6 00016-08001-33 Predawn Gray Mica 1H1 00016-08001-34 Black 202 00016-08001-35 Salsa Red Pearl 3Q3 00016-08001-36 Sandy Beach Metallic 4T8 00016-08001-37 Cypress Pearl 6T7 00016-08001-38 Mistic Teal Mica 785

Left Side Replacement Color Code00016-08001-40 Super White 040 00016-08001-41 Blizzard Pearl 070 00016-08001-42 Silver Sky Metallic 1D6 00016-08001-43 Predawn Gray Mica 1H1 00016-08001-44 Black 202 00016-08001-45 Salsa Red Pearl 3Q3 00016-08001-46 Sandy Beach Metallic 4T8 00016-08001-47 Cypress Pearl 6T7 00016-08001-48 Mistic Teal Mica 785

Southeast Toyota Distributors, LLC Page 4 of 4

NOTE: Due to the inconsistency of factory sealant, it may be necessary to apply the bodyside molding over the clear door edge film protection.