color television receiver - go-gddq. · pdf filecolor television receiver chassis : s51a model...

COLOR TELEVISION RECEIVERChassis : S51A Model : CS298CV

COLOR TELEVISION RECEIVER CONTENTS

Precautions

Specifications and IC Data

Disassembly and Reassembly

Alignment and Adjustment

Troubleshooting

Exploded View and Parts List

Electrical Parts List

Block Diagram

PCB Layout Diagram

Wiring Diagram

Schematic Diagrams

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

ELECTRONICS

© Samsung Electronics Co., Ltd. MAR. 2000Printed in Korea3S51A-9401

1. Precautions

1-1 Safety Precautions

1. Be sure that all of the built-in protectivedevices are replaced. Restore any missingprotective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protectivedevices, including: nonmetallic control knobsand compartment covers.

3. Make sure that there are no cabinet openingsthrough which people—particularly children—might insert fingers and contactdangerous voltages. Such openings includethe spacing between the picture tube and thecabinet mask, excessively wide cabinetventilation slots, and improperly fitted back

covers.

If the measured resistance is less than 1.0megohm or greater than 5.2 megohms, anabnormality exists that must be correctedbefore the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1):Warning: Do not use an isolation transformer during this test. Use a leakage-current tester or a metering system that complies with American National StandardsInstitute (ANIS C101.1, Leakage Current forAppliances), and Underwriters Laboratories(UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plugthe AC line cord directly into the power outlet. With the unit’s AC switch first in theON position and then OFF, measure the current between a known earth ground (metalwater pipe, conduit, etc.) and all exposedmetal parts, including: antennas, handlebrackets, metal cabinets, screwheads and control shafts. The current measured shouldnot exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat thetest.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check: With the unit’s AC plug disconnected from theAC source, connect an electrical jumper acrossthe two AC prongs. Connect one lead of theohmmeter to an AC prong. Connect the otherlead to the coaxial connector.

7. X-ray Limits:The picture tube is especially designed to pro-hibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube onlywith one that is the same type as the original.Carefully reinstall the picture tube shields andmounting hardware; these also provide X-rayprotection.

8. High Voltage Limits:High voltage must be measured each time ser-vicing is done on the B+, horizontal deflectionor high voltage circuits. Correct operation ofthe X-ray protection circuits must be reconfirmed whenever they are serviced.(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These includethe X–ray Protection Specifications Label, andthe Product Safety and X-ray Warning Note onthe service data schematic.

Precautions

Samsung Electronics 1-1

LEAKAGECURRENTTESTER

DEVICEUNDERTEST

TEST ALLEXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITHPLUG REVERSED

(USING AC ADAPTERPLUG AS REQUIRED)

EARTHGROUND

(READING SHOULDNOT BE ABOVE

0.5mA)

Follow these safety, servicing and ESD precautions to prevent damage and protect against potentialhazards such as electrical shock and X-rays.

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specifiedlimits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, checkeach of the special components.

10. Design Alteration Warning:Never alter or add to the mechanical or electrical design of this unit. Example: Do notadd auxiliary audio or video connectors. Suchalterations might create a safety hazard. Also,any design changes or additions will void themanufacturer’s warranty.

11. Hot Chassis Warning:Some TV receiver chassis are electrically connected directly to one conductor of the ACpower cord. If an isolation transformer is notused, these units may be safely serviced onlyif the AC power plug is inserted so that thechassis is connected to the ground side of theAC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the ACpower plug, reverse its polarity and reinsert.Re-measure the voltage between the chassisand ground.

12. Some TV chassis are designed to operate with85 volts AC between chassis and ground,regardless of the AC plug polarity. These unitscan be safely serviced only if an isolationtransformer inserted between the receiver andthe power source.

13. Some TV chassis have a secondary groundsystem in addition to the main chassis ground.This secondary ground system is not isolated from the AC power line. The twoground systems are electrically separated byinsulating material that must not be defeatedor altered.

14. Components, parts and wiring that appear tohave overheated or that are otherwise damaged should be replaced with parts thatmeet the original specifications. Always determine the cause of damage or overheat-ing, and correct any potential hazards.

15. Observe the original lead dress, especiallynear the following areas: Antenna wiring,sharp edges, and especially the AC and highvoltage power supplies. Always inspect forpinched, out-of-place, or frayed wiring. Donot change the spacing between componentsand the printed circuit board. Check the ACpower cord for damage. Make sure that leadsand components do not touch thermally hotparts.

16. Picture Tube Implosion Warning:The picture tube in this receiver employs“integral implosion” protection. To ensurecontinued implosion protection, make surethat the replacement picture tube is the sameas the original.

17. Do not remove, install or handle the picturetube without first putting on shatterproofgoggles equipped with side shields. Neverhandle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently attached deflection yoke; do nottry to remove such “permanently attached”yokes from the picture tube.

18. Product Safety Notice: Some electrical and mechanical parts havespecial safety-related characteristics whichmight not be obvious from visual inspection.These safety features and the protection theygive might be lost if the replacement compo-nent differs from the original—even if thereplacement is rated for higher voltage,wattage, etc.

Components that are critical for safety areindicated in the circuit diagram by shading, ( ) or ( ).

Use replacement components that have thesame ratings, especially for flame resistanceand dielectric strength specifications. A replacement part that does not have thesame safety characteristics as the originalmight create shock, fire or other hazards.

Precautions

1-2 Samsung Electronics

!

1-2 Servicing Precautions

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord fromthe AC power source before attempting to: (a)Remove or reinstall any component or assembly, (b) Disconnect an electrical plug orconnector, (c) Connect a test component inparallel with an electrolytic capacitor.

3. Some components are raised above the printedcircuit board for safety. An insulation tube ortape is sometimes used. The internal wiring issometimes clamped to prevent contact withthermally hot components. Reinstall all suchelements to their original position.

4. After servicing, always check that the screws,components and wiring have been correctlyreinstalled. Make sure that the portion aroundthe serviced part has not been damaged.

5. Check the insulation between the blades of theAC plug and accessible conductive parts(examples: metal panels, input terminals andearphone jacks).

6. Insulation Checking Procedure: Disconnect thepower cord from the AC source and turn thepower switch ON. Connect an insulationresistance meter (500V) to the blades of the ACplug.

The insulation resistance between each bladeof the AC plug and accessible conductive parts(see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks.Do not apply AC power to the unit (or any ofits assemblies) unless all solid-state heat sinksare correctly installed.

8. Always connect a test instrument’s groundlead to the instrument chassis ground beforeconnecting the positive lead; always removethe instrument’s ground lead last.

Precautions


Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Some semiconductor (“solid state”) devicesare easily damaged by static electricity. Suchcomponents are called ElectrostaticallySensitive Devices (ESDs); examples includeintegrated circuits and some field-effect transistors. The following techniques willreduce the occurrence of component damagecaused by static electricity.

2. Immediately before handling any semiconductor components or assemblies, drain theelectrostatic charge from your body by touching a known earth ground. Alternatively,wear a discharging wrist-strap device. (Besure to remove it prior to applying power—this is an electric shock precaution.)

3. After removing an ESD-equipped assembly,place it on a conductive surface such as aluminum foil to prevent accumulation ofelectrostatic charge.

4. Do not use freon-propelled chemicals. Thesecan generate electrical charges that damageESDs.

5. Use only a grounded-tip soldering iron whensoldering or unsoldering ESDs.

6. Use only an anti-static solder removal device.Many solder removal devices are not rated as“anti-static”; these can accumulate sufficientelectrical charge to damage ESDs.

7. Do not remove a replacement ESD from itsprotective package until you are ready toinstall it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protectivematerial from the leads of a replacement ESD,touch the protective material to the chassis orcircuit assembly into which the device will beinstalled.

9. Minimize body motions when handlingunpackaged replacement ESDs. Motions suchas brushing clothes together, or lifting a footfrom a carpeted floor can generate enough static electricity to damage an ESD.

Precautions


1-3 Precautions for Electrostatically Sensitive Devices (ESDs)



2. Specifications and IC Data

2-1 Specifications

T e lev is io n S y s tem :

C hann e ls :

In term ediate-F requ enc ies (MH z ):

P ic tu re T ub e:

P ower R equ irem ents : AC 100 ~ 260V, 50/60H Z or AC 160 ~ 260V, 50/60H Z

Antenn a Inp u t Im pedanc e :V H F ,U H F : T eles c op ic dip o le antenn a(75Ω unb alanc ed ty pe )

Speak er Im pedanc e : 8Ω , 10W + 10W

MO D E L S YS T E M

CI P AL -I (U H F )

CII P AL -I (V H F /U H F )

CX P AL -B /G ,S E C AM-B/G

CK P AL -B /G ,D /K,S E C AM-B /G ,D /K

CB P AL -B /G

CS P AL -B /G ,D /K,S E C AM-B /G ,D /K,NT4 .43,NT3.58

SYSTEMBAND

PAL/SECAM-B/G,I

PAL/SECAM-D/K

SECAM-K1,PAL-D NTSC-M

VHF 2-12 1-13 2-9 2-13

UHF 21-69 21-69 13-57 14-69

SYSTEMBAND

PAL/SECAM-B/G

PAL/SECAM-D/K,K1

PAL-I NTSC-M

Picture IF Carrier 38.90 38.90 38.90 38.90

Sound IF Carrier 33.40 32.40 32.90 34.40

Color Sub Carrier 34.47 34.47 34.47 35.32

25 Inch A59KPR84XQuick start, in-line-gun,Black stripe,90° degree deflection

29 Inch

30 Inch

A68KVL74X

A70QBZ791X

2-2 IC Line Up



L O C NO NO S pecification D escription R emarks

H IC 101 1 P AP 103T IF P R E -AMP

IC 201 2TD A8844 P AL /S E C AM/NTS C /S E C AM-L

TD A8843 P AL /NTSC

IC 301 3 L A7845 VE R TIC AL D E F L E C T IO N AMP

IC 501 4 TD A6108 R G B D R IVE AMP

IC 601 5TD A7297 S O U ND AMP (10W/C H )

TD A7266S SO U ND AMP (5W/C H )

IC 701 6 TD A9859 AU D IO P R O C E S S O R

IC 801 7 KA3S 1265R SMP S IC (12A)

IC 802 8 P C 123Y P H O TO C O U P L E R

IC 803 9 78R 05 S WITC H ING R E G U L ATO R

IC 804 10 K A7630 SWITC H ING R E G U L ATO R (5,8V )

IC 901 11 S ZM503AT MIC O M

IC 902 12 24C 040 E E P R O M

IC E 01 13 4558 EW D R IV E AMP

IC N01 14 TD A9808 SIF D E TE C TO R NIC AMMO D U L EIC N02 15 TD A9874H NIC AM D E MO D U L ATO R

IC A01 16 L A7567N SIF D E TE C TO R A2 S TE R E OMO D U L EIC A02 17 TD A9873H A2 D E MO D U L ATO R

IC M01 18 L A7566 SIF & FM D E TE C TO R MO NO

IC P 01 19 TE A5114 V ID E O SWITC HPIP

MO D U L EIC P 02 20 TD A9160A P AL /NTSC D E C O D E R

IC P 03 21 S D A9288 PIP V ID E O P R O C E SS

IC T01 22 S AA5261 TTX -D E C O D E R TTXMO D U L EIC T02 23 24C 02 E E P R O M(TTX P AG E ME MO R Y)

2-3 Semiconductor Base Diagrams



ELECTROLYTIC-CONDENSER

ICDIODE

TDA4665(Pin 16)TDA837X(Pin 56)Z8933112PSC(Pin 42)X24CO4P(Pin 8)TDA8395(Pin 16)TDA4665(Pin 16)

IC TRANSISTOR TRANSISTOR

TDA8133

KA7812

ING

OUT

TRANSISTORTRANSISTOR

2SD16512SD1650KSD5072KSD5071KSD1711

BC

EE B C

KSA815-YKSA539-Y

IC

UPC574Jor

KA33V

G1962K2950MK9253M

SAW-FILTER

1

E C B

KSR1012KSR1010KSR2010

Fig. 2-1 Semiconductor Base Diagrams


MEMO

Disassembly and reassembly


3. Disassembly and Reassembly

3-1 Back Cover Removal

1. After removing the 7 screws, pull the cabinet backwards.

3-2 Main Board Removal



1

2

3

4

5

6

7

8

910

11

12

13

1. Separate the TBC-wire 2P connector from GT501,GT502.

2. Separate the CRT Assay from the CRT socket.

3. Remove the Anode Cap from the CRT.

4. Separate the D-Coil Connector from CN802.

5. Separate the AC cord from CN801.

6. Separate the DC connector from CN401.

7. Separate the CN501B 8P CRT connector from CN501.

8. Separate the CNA05 5P A/V side connector from CN602.

9. Separate the CNA01 8P CRT connector from CN701.

10. Separate the Focus,Screen Wire from the FBT clamper.

11. Separate the TBC wire 2P, speaker wires from the wire clamper.

12. Separate the CN701, CN602 connector from the wire clamper.

13. Separate the AC cord from the wire clamper.

14. Remove the main board by pulling it with both hands.

3-3 Speaker Removal



7

1. Remove the speaker bypressing the tension rib.

1. Separate the speaker wires from D-coil(located on the bottom to the right side).

2. Remove the screws.



3-4 CRT Removal

1. Remove the 4 nuts mounting the CRT to the front cabinet. Pull the CRT backwards.

2. Caution: Because of the high vacuum and large surface area of the picturetube, be careful while handling it: (1) Always lift the picture tube bygrasping it firmly around the faceplate, (2) Never lift the tube by its neck.(3) Do not scratch the picture tube or apply excessive pressure. Fracturesof the glass may cause an implosion.

Alignment and Adjustments


4. Alignment and Adjustments

4-1 Preadjustment

4-1-1 Factory Mode

1. Do not attempt these adjustments in the VideoMode.

2. The Factory Mode adjustments are necessarywhen either the EEPROM (IC902) or the CRTis replaced.

3. Do not tamper with the ÒAdjustmentÓ screenof the Factory Mode menu. This screen isintended only for factory use.

4-1-2 When EEPROM (IC902) Is Replaced

1. When IC902 is replaced all adjustment datarevert to initial values. It is necessary tore-program this data.

2. After IC902 is replaced, warm up the TV for10 seconds.

4-1-3 When CRT Is Replaced

1. Make the following adjustments AFTER set-ting up after setting up purity and conver-gence :

White Balance Sub-Brightness, Sub-Contrast Vertical Center Vertical SizeHorizontal Size Fail Safe (This adjustment must be the laststep).

4-2 Factory/Service Mode

4-2-1 Procedure for the “Adjustment” Mode

1. This mode uses the standard remote control.The Service Mode is activated by entering thefollowing remote-control sequence :

(1) STAND-BY® DISPLAY® MENU® MUTE®POWER ON.

2. The ÒSERVICE (FACTORY)Ó message will bedisplayed. The Service Mode has four compo-nents: Adjustment, Test Pattern, Option Bytesand Reset.

3. Access the Adjustment Mode by pressing theÒVOLUMEÓ keys ( Up or Down). The adjust-ment parameters are listed in the accompany-ing table, and selected by pressing the CHAN-NEL keys ( ,).

4. Selection sequences for the PAL/NTSC system:

DOWN or UP key:

AGC↔VCO↔SBT↔SCT↔SCR↔SC↔RG↔

BG↔CDL↔STT↔PDL↔VOL↔PSL↔PVS↔

PVA↔PHS↔PEW↔PEP↔PEC↔PET↔VSC↔

TSC↔SA↔QEW↔PCT↔PTT↔PHM↔PVP↔

NVP↔PHP↔NSR↔FFI↔AGC.

5. The VOLUME keys increase or decrease theadjustment values (stored in the non-volatile memory) when Adjustment Modeis cancelled.

6. Cancel the Adjustment Mode by re-pressingthe ÒHIDDENÓ or ÒPower OFF/ONÓ keys.

4-2-2 Main Adjustment Parameters



OSD FUNCTION RANGE

AGC AUTO GAIN CONTROL 0 ~ 63

VC O VOLTAGE CONTROLLED OSCILLATOR 0 ~127

SBT SUB BRIGHT 0 ~ 23

SCT SUB CONTRAST 0 ~ 23

SC R SUB COLOR 0 ~ 23

SC S-CORRECTION 0 ~ 63

RG RED DRIVE GAIN 0 ~ 63

BG BLUE DRIVE GAIN 0 ~ 63

C DL CATHODE DRIVE LEVEL 0 ~ 7

STT SUB TINT 0 ~ 13

PDL PAL DELAYTIME 0 ~ 15

VOL VOLUME LEVEL 0 ~100

PSL PAL VERTICAL SLOP 0 ~ 63

PVS PAL VERTICAL SHIFT 0 ~ 63

PVA PAL VERTICAL AMPLITUDE 0 ~ 63

P HS PAL HORIZONTAL SHIFT 0 ~ 63

P EW PAL EW-WIDTH 0 ~ 63

PEP PAL EW-PARABOLA 0 ~ 63

P E C PAL EW-CORNER PARABOLA 0 ~ 63

PET PAL EW-TRAPEZIUM 0 ~ 63

VSC VERTICAL SCROLL 0 ~ 63

TSC TTX SUB CONTRAST 0 ~ 63

SA SEPARATION ADJUSTMENT 0 ~ 14

QEW Q EW-WIDTH 0 ~ 15

PCT CONTRAST 0 ~ 15

PTT PIP TINT 0 ~ 63

P HM HORIZENTAL MOVE 0 ~ 15

PVP PAL VERTICAL POSITION 0 ~63

NVP NTSC VERTICAL POSITION 0 ~ 63

P HP HORIZENTAL POSITION 0 ~ 63

NSR NTSC SUB COLOR 0 ~ 23

FFI FAST FILTER IF-PLL 0 ~ 1

PIP

PIP

PIP

PIP

PIP



4-2-3 Test Pattern

1. This mode can be used during servicing, or for confirming that the convergence and purity adjustmentsare correct.

2. Access the Test Pattern parameters by pressing a CHANNEL keys ( ,) while the Service Mode is on.The cursor will move to the test pattern. Press the VOLUME keys. On-screen display:

• RED• GREEN • BLUE• WHITE

3. AGING Mode (Reference Only)

This pattern is used for pre-heating the CRT during manufacturing--it is accessed in the factory bytwice pressing the ÒHIDDEN Ò key.

Even if the TV power is cut off, the Aging Mode is not cancelled, The AGING mode is cancelled byrepressing the ÒHIDDENÓ or any key on the front pannel.

2 (C H ) P D L 0 (F IXE D ) TSC 40

AG C 18 (F IXE D ) V O L 25 (F IXE D ) SA 25(F IX E D )

V C O 80 (F IXE D ) P S L 31 (F IXE D ) Q E W 5

SBT 7 P V S 31 PCT 7(F IX E D )

SCT 16 P V A 31 PTT 31(F IX E D )

S C R 5 (F IXE D ) P H S 40 P H M 8(F IX E D )

SC 11 (F IXE D ) P E W 38 P VP 31(F IX E D )

RG 31 P E P 22 NVP 31(F IX E D )

BG 31 P E C 22 P H P 42(F IX E D )

C D L 7 (F IXE D ) PET 30 NSR 3(F IX E D )

STT 10 (F IXE D ) V SC 31 (F IXE D ) FFI 1:INDIA,0:OTHERS

OSD INITIAL OSD OSDINITIAL INITIAL

FACTORY MODE VALUE



4-2-4 Option Byte Table

O P T IO N O S D NO T E

SY STE M

CS MU L TI S YS TE M

C S-C H INA WITH O U T S E C AM SY S TE M

C B / CII P AL -B /G & P AL -I

C K / CX P AL /SEC AM B/G ,D /K

NO R MAL / ZOOM / 16 :9

S E L E C T A MO D E AV AIL AB L E TOAD JU S T P -S IZE

P L U S /ZOOM

NO R MAL /ZOOM

P L U S / NORMAL

PLUS / NORMAL/ ZOOM / 16:9

PIPON PIP U SE D

O F F PIP D E L E TE D

JAC KSC AR T 21P IN JAC K U SE D

R C A R C A JAC K U S E D

AU D IO

NIC AM NIC AM MO D U L E U S E D

S TE R E O A2 MO D U L E U S E D

L -S TE R E O MO NO & L INE STE R E O U SE D

MO NO MO NO U S E D

O NE C H IPTD A8844 C R T (MO R E TH AN 22-INC H ) U S E D

TD A8842 C R T (MO R E TH AN 21-INC H ) U S E D

System : csNormal / Zoom / 16:9Pip : onJack : RCAAudio : NicamOne Chip : TDA8844Language : EnglishText : ON X-prot : OFFS-sytem : B/G



O P T IO N O S D NO T E

L ANG U AG E

E NG L IS H O NL Y

AR AB E NG L IS H / AR ABIAN

P E R SIAN E NG L IS H / P E R SIAN

F R ANCH E NG L IS H / F R E NC H

C H INA E NG L IS H / C H INE S E

IND O NE SIA E NG L IS H / IND O NE SIAN

MAL AYS IA E NG L ISH / MAL AYS IAN

TH AI E NG L ISH / TH AI

V IE TNAM E NG L ISH / V IE TNAME S E

AR AB /FRANCH E NG L ISH / AR AB IAN / F R E NC H

MU L TIE NG L ISH / AR AB IAN / P E R SIAN / F R E NC H/ C H INE S E / IND O NE SIAN / MAL AYS IAN/ THAI/ V IE TNAM

TE XTON TTX U S E D

OFF TTX D E L E TE D

X -P R O TON X -R AY P R O TE C TO R U SE D

OFF NO X-R AY P R O TE C TO R F U NC T IO N

S -SY S TE M

B/G 1.TH E SO U ND SY STE M C O ME S F IR S TIN AU TO S E AR C H

2.SO U ND SY STE M IN F AC TO R Y MO D ER E S E T

3."AU TO " MO D E IS S H O WN O NL Y WH E NL -STE R E O OR MO NO IS SE L E C TE D IN THEAU D IO MO D E .

I

D/K

M

AU TO

ENGLISH



4-3 Other Adjustments

4-3-1 General

1. Usually, a color TV needs only slight touch-up adjustment upon installation. Check thebasic characteristics such as height, horizontaland vertical sync and focus.

2. The picture should have good black and whitedetails. There should be no objectionablecolor shading; if color shading is present, per-form the purity and convergence adjustmentsdescribed below.

3. Use the specified test equipment or its equiva-lent.

4. Correct impedance matching is essential.

5. Avoid overload. Excessive signal from a sweepgenerator might overload the front-end of theTV. When inserting signal markers, do notallow the marker generator to distort testresults.

6. Connect the TV only to an AC power sourcewith voltage and frequency as specified on thebackcover nameplate.

7. Do not attempt to connect or disconnect anywires while the TV is turned on. Make surethat the power cord is disconnected beforereplacing any parts.

8. To protect against shock hazard, use an isola-tion transformer.

4-3-2 Automatic Degaussing

A degaussing coil is mounted around the pic-ture tube, so that external degaussing aftermoving the TV should be unnecessary. Butthe receiver must be properly degaussed uponinstallation.

The degaussing coil operates for about 1 sec-ond after the power is switched ON. If the sethas been moved or turned in a different direc-tion, disconnect its AC power for at least 30minutes.

If the chassis or parts of the cabinet becomemagnetized, poor color purity will result. Ifthis happens, use an external degaussing coil.Slowly move the degaussing coil around thefaceplate of the picture tube and the sides andfront of the receiver. Slowly withdraw the coilto a distance of about 6 feet before removingpower.

4-2-5 RESET

The Reset Mode is used during factory inspection. Function Reset:

1. Channels Add/Erase2. Language Basic (English)



4-3-3 High Voltage Check

CAUTION: There is no high voltage adjustment on this chassis.The B+ power supply must be set to +130 volts (Full color bar inputand normal picture level).

1. Connect a digital voltmeter to the secondanode of the picture tube.

2. Turn on the TV. Set the Brightness andContrast controls to minimum (zero beam cur-rent).

3. The high voltage should not exceed 33KV.

4. Adjust the Brightness and contrast controls toboth extremes. Ensure that the high voltagedoes not exceed 33KV under any conditions.

4-3-4 FOCUS Adjustment

1. Input a black and white signal.

2. Adjust the tuning control for the clearestpicture.

3. Adjust the FOCUS control for well definedscanning lines in the center area of the screen.

4-3-5 Screen Adjustment

1. Connect CRT socket pin GK, BK, RK to anoscilloscope probe.

2. Input a gray scale pattern. (Use a patterngenerator, PM5518)

3. Use the Picture mode for the STANDARD pic-ture.

4. Adjust the Screen VR (on the FBT) so that thevoltage on the oscilloscope becomes 130+2.5V(See Fig. 4-1).

4-3-6 Purity Adjustment

1. Warm up the receiver for at least 20 minutes.

2. Plug in the CRT deflection yoke and tightenthe clamp screw.

3. Plug the convergence yoke into the CRT andset in as shown in Fig. 4-2.

4. Input a black and white signal.

5. Fully demagnetize the receiver by applying anexternal degaussing coil.

6. Turn the CONTRAST and BRIGHTNESS con-trols to maximum.

7. Loosen the clamp screw holding the yoke.Slide the yoke backward or forward to pro-vide vertical green belt. (Fig. 4-3).

8. Tighten the convergence yoke.

9. Slowly move the deflection yoke forward,and adjust for the best overall green screen.

10. Temporarily tighten the deflection yoke.

11. Produce blue and red rasters by adjusting thelow-light controls. Check for good purity ineach field.

12. Tighten the deflection yoke.

Fig. 4-1

130 2.5V+_

GND

_



4-3-7 White Balance Adjustment

Fig. 4-2 Convergence Magnet Assembly

4 Pole Magnet

6 Pole Magnet 2 Pole Magnet

ClamperScrew

2 POLEPURITY

YOKECLAMPSCREW

6 POLECONVERGENCE

4 POLECONVERGENCE

Fig. 4-3 Center Convergence Adjustment

31m/m

Vertical Green Belt

Fig. 4-4

1

2

(a) Set up

1. Warm up the TV for at least 30 minutes in theWhite Pattern.

2. Input a Toshiba pattern.

(b) High-Light Adjustment

Set SCT to 50 ± 5 fL in the Factory Service Mode with using CA100. (See Fig. 4-4 ①)

(c) Low-Light Adjustment

Set SBT to 1.2 ± 0.2 fL in the Factory Service Mode with using CA100. (See Fig. 4-4 ➁)



4-3-8 Center Convergence Adjustment

1. Warm up the receiver for at least 20 minutes.

2. Adjust the two tabs of the 4 pole magnets tochange the angle between them. Superimposethe red and blue vertical lines in the centerarea of the screen.

3. Adjust the Brightness and Contrast controlsfor a well defined picture.

4. Adjust the two-tab pairs of the 4 pole mag-nets, and change the angle between them.Superimpose the red and the blue verticallines in the center area of the screen.

5. Turn the both tabs at the same time, keepingthe angle constant, and superimpose the redand blue horizontal line in the center of thescreen.

6. Adjust the two-tab pairs of the 6-pole magnetsto superimpose the red and blue line onto thegreen. (Changing the angle affects the verticallines, and rotating both magnets affects thehorizontal lines.)

7. Repeat adjustments 2~6, if necessary.

8. Since the 4-pole magnets and 6-pole magnetsinteract, the dot movement is complex(Fig. 4-5).

Fig. 4-5 Center Convergence Adjustment

REDBLUE

BLUE

RED

4-Pole Magnet Movement

GREENRED/BLUE

RED/BLUE

GREEN

6-Pole Magnet Movement

4-3-9 RF AGC Adjustment

1. Tune to the strongest local station.

2. Enter the Factory Service Mode to make adjustments.

3. Adjust the AGC control untill noise(snow) disappears from the screen.



4-3-10 Geometry Adjustment

1. Inp u t a lio n head pattern.

2. Adju s t P V S s o that the p ic tu re is v er tic a lly c en tered .

3. Adju s t with P V A s o that the top and bottom m argin s of the p ic tu re a re 4 .

4. Adju s t P H S s o tha t the p ic ture is ho r iz on ta lly c en tered .

5. Adju s t with P E W s o that the le ft and r ig h t m argin s of the p ic tu re a re 5 .

6. Inpu t a crossha tch patte rn.

7. Adju s t P E P , P E C , P E T for vertica l linearity .

4

4

5 5

Troubleshooting


5. Troubleshooting

5-1 No Video (Raster On, No Sound)

Yes

No

Check/ReplaceTU101, HC101

NoMeasure theVoltage of each of, 8 pins

of TU101

Check IC901 Pins 39, 40

See "No Video"(Sound OK)

See "No Sound"(Video OK)

Check/ReplaceIC901,IC201,IC902 ,IC701,

Audio Module

Yes

5-2 No Power

Troubleshooting


Yes

No

No

Yes

No

No

No

Check the 130V,12.7V B+ Lines

Check IC804 Pin 9 (5V)

Check/ReplaceIC801, D802

Check/ReplaceIC804(KA7630),DZ905,DZ804

Check IC901 Pin 18 ; Stand-by : 0V

Normal : 5V

Check/ReplaceIC901

Check IC901Pin 8 (4V).

Check/ReplaceIC901(m-com)

Check IC201,Pin 40 (H-out)

Check/ReplaceIC201, Q402, Q403

NoCheck Q402, Q403

Check/ReplaceDZ805, IC802

Yes

Yes

Yes

5-3 No Video (Sound OK)

Troubleshooting


Yes

No

No

Yes

No

No

Check IC201 Pin 6 (CVBS)

Check/ReplaceIC201

Check IC201Pins 19, 20, 21(R/G/B-OUT)

Check IC202pin 27 (Y-IN)

Check/ReplaceIC201,D205,DZ204

Check IC501,on the CRT PCB

Check/ReplaceIC501

Check/ReplaceR505 (HEATER 6.3Vrms)

CRT, V999

Yes

NoCheck IC201 Pin 12,37 (8V)

Check/ReplaceIC804 KA7630

Yes

Yes

2Vp-p

Troubleshooting


5-4 No Sound (Video OK)

No

No

CHECK/REPLACEA/V Front Assembly.

CHECK IC701Pin 3,5

CHECK/REPLACESound Module (MD701)

CHECK/REPLACEIC701, C712, C719

CHECK IC601 Pin

Sound output

CHECK/REPLACEIC601, R601, R602

CHECK IC701Pin 15,18

Yes

Yes

No

Yes

1 14 152

5-5 Power OFF/ON (Repeatedly)

CHECK Q403COLLECTOR H-PULSE SEE " NO-POWER"

NO

YES

CHECK IC901PIN26(H-SYNC )

CHECK/REPLACEIC901,Q907,C913DZ402

NO

YES

CHECK IC301PIN7(V-BLANK)

CHECK/REPLACEQ301,Q302,D304

YES

NO

CHECK PIN6(+16.5V)PIN1(-14V)

CHECK/REPLACER409,R413,D407,D410DZ302,DZ303

NO

YES

CHECK/REPLACEIC301,IC201

Troubleshooting


5-6 SMPS (Power Supply) Does Not Function

(1) When F 802 is open :C heck/Replace F 802 , IC 801 , D 802.

(2) When F 802 is okay, but SMP S does not function:C heck/Replace D Z801 , D Z808 , IC 802 , D Z805 .

(3) O the rs : S ee "5. Troubleshooting"

6. Exploded View & Parts List

6-1 CS298CV

Exploded View & Parts List


No Code No Description;Specification Q’ty Remark

1 AA92T30001D A1SSY CABINET FRONT;294C 1

AA64-31086A CABINET-FRONT;-,294C,-,HIPS,HB,BLK,-,- 1

1-1 AA64-60366L INLAY-AV;5099.5399,KSP213 EG PAL S/T,PS 1

1-2 AA64-10606B KNOB-POWER;-,50.5399,MASTER,ABS,HB,M/B 1

1-3 AA61-60003J SPRING-CS;-,SUS304,0.5,OD6,H12,N7,-,-,- 1

1-4 AA64-40390A WINDOW-REMOCON;-,99,-,ABS,HB,LG41338,- 1

1-5 AA63-30204A COVER-CONTROL;-,294C,-,HIPS,HB,BLK,-,- 1

1-6 AA64-40391B INDICATOR-LED;-,99,-,ACRYL,-,CLEAR,- 1

1-7 AA64-70117B BADGE-BRAND;AL,SS,SILVER,L65,R2000,-,- 1

1-8 AA65-30018A CLAMP-WIRE;NYLON-66,-,-,DATL-600,DONG-A,- 2

1-9 AA64-10702A KNOB-CONTROL;-,294C,-,ABS,HB,BLK 1

1-10 4901033412 TAP SCREW;ST4X12 VWT 2

1-11 AA61-40053A STOPPER-PCB;ALL MODEL,HIPS HB,WHT,HB,-,- 1

1-12 AA61-40010A BOSS-WING;,HIPS,HB,NTR,-,- 2

1-13 AA64-10702A KNOB-CONTROL;-,294C,-,ABS,HB,BLK 1

1-14 4901031165 TAP SCREW;ST4*16+E25SJ2831-87 1

2 6126817402 29CRT;A68QBT892X(TSDD) 1

2-1 7020100001 D-COIL-CLAMP;JG8.688.002 8

2-2 SCREW-ASSY DELETE ITEM

2-3 5402922015-4 D-COIL;BRE4.799.015-3A 1

2-4 3704-001105 SOCKET-CRT;11P,20PI,26.5PI,NI,- 1

3 7022903002G HOLDER SPEAKER;JG7.013.002 2

3-1 4901031425 TAP SCREW;ST4X12 SJ2831-87 8

3-2 SPEAKER BRACKET DELETE ITEM

3-3 3001-000151 SPEAKER;20W,8ohm,92dB,110Hz 2

3-4 4901031425 TAP SCREW;ST4X12 SJ2831-87 8

4 AA92T40001I A1SSY CABINET-BACK;294C 1

4-1 4901031460 TAP SCREW;ST4*16FT-D.ZN.DJ SJ2831-87 7

4-2 AA64-60233J INLAY-BACK;S51A,CHINA 9PIN,PS,T0.5,BLK,-, 1

4-3 AA61-20284A HOLDER;-,P-CORD,PP,VO,BLK,KE-002 1



7-1 CS298CV

ASSY-PCB,MAIN(COM)+D1358

* AA97T10001CASSY-PCB,MAIN(COM)+D1358; CS-298CV,S51A

C606 2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mmC913 2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mmBRACK AA61-10386A BRACKET-IC;-,-,SECC 100,T1.0,-,KA2S0680,-C101- AA39-20009C LEAD CONNECTOR-AS;SY -,YFH800-01,-,1P,400,1617#22C102 2401-002594 C-AL;220uF,20%,16V,GP,TP,8x11.5,5C103 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C104 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C105 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C106 2401-001082 C-AL;330nF,20%,50V,GP,TP,5x11,5C107 2401-000914 C-AL;22uF,20%,16V,GP,TP,5x11,5C109 2202-000796 C-CERAMIC,MLC-AXI;AL 1NF,10%,50V,Y5P,TP,3.5X1.9MM,-C110 2202-000796 C-CERAMIC,MLC-AXI;AL 1NF,10%,50V,Y5P,TP,3.5X1.9MM,-C111 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C207 2401-001026 C-AL;3.3UF,20%,50V,GP,TP,5X11,5C210 2306-000122 C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0mm,C211 2401-002619 C-AL;47uF,20%,25V,GP,TP,5x11,5C213 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5mC214 2401-000660 C-AL;2.2uF,20%,50V,GP,TP,5x11,5C215 2305-000412 C-FILM,MPEF;470nF,5%,63V,TP,-,5mmC216 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5C217 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,C218 2305-000411 C-FILM,MPEF;470nF,5%,50V,TP,7.3x4.8x5.5mm,C219 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5C220 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5C221 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mmC222 2305-000412 C-FILM,MPEF;470nF,5%,63V,TP,-,5mmC223 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C224 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C225 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C226 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5C227 2201-000986 C-CERAMIC,DISC;12pF,5%,50V,NPO,TP,5x3mm,2.5mmC228 2201-000273 C-CERAMIC,DISC;18pF,5%,50V,CH,TP,5x3mm,5C229 2301-000356 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mmC230 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mmC231 2202-000183 C-CERAMIC,MLC-AXI;AL

2.2NF,20%,16V,Y5R,TP,3.5X1.9MMC232 2202-000127 C-CERAMIC,MLC-AXI;AL 10nF,+80-20%,25V,Y5V,TP,-,7.5C233 2309-000138 C-FILM,PE-PPF;100nF,5%,50V,TP,20x16x8.5,7.5mC234 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mmC235 2202-000849 C-CERAMIC,MLC-AXI;AL 18pF,5%,50V,CH,TP,3.5x1.9,-C236 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C237 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,C238 2301-000342 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm,5C239 2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mmC240 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5C241 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5C242 2202-000183 C-CERAMIC,MLC-AXI;AL

2.2NF,20%,16V,Y5R,TP,3.5X1.9MMC243 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5C244 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5mC245 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,C301 2301-000254 C-FILM,PEF;39nF,5%,50V,TP,7.5x3.5x6.5mm,5C302 2401-000360 C-AL;100uF,20%,50V,GP,TP,8x11.5,5C303 2201-000192 C-CERAMIC,DISC;10pF,0.3pF,500V,CH,TP,7x4,5C304 2305-000285 C-FILM,MPEF;220NF,5%,100V,TP,10.5X5.5X15MMC305 2305-000149 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5,5C306 2301-000530 C-FILM,PEF;100nF,5%,100V,TP,11.5x12.5x6.5C307 2401-000326 C-AL;100uF,20%,35V,GP,TP,8x11.5,5C308 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5C309 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5C403 2401-000901 C-AL;22uF,20%,160V,GP,TP,10x20,5

C404 2201-000291 C-CERAMIC,DISC;1nF,10%,500V,Y5P,TP,8.5x5MM,5C405 2401-002268 C-AL;2.2uF,20%,250V,LZ,TP,8X11,5C406 2306-000272 C-FILM,MPPF;820nF,5%,400V,BK,29x25.5x18.5,C407 2201-000984 C-CERAMIC,DISC;680pF,10%,2KV,Y5P,TP,11x6,7.5mC408 2305-000382 C-FILM,MPEF;4.7nF,5%,400V,TP,-,5mmC409 2201-000551 C-CERAMIC,DISC;470pF,10%,1KV,Y5P,TP,8x5,5C410 2401-001397 C-AL;470uF,20%,25V,GP,TP,10x16,5C411 2305-000178 C-FILM,MPEF;10nF,5%,100V,TP,-,5mmC412 2201-000599 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5C413 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5C414 5129946822Q C-M.TERYLENE;CBB81-1.6KV-6800PF J L=20C415 5129947822Q C-M.POLYPROPYLENE;CBB81-1.6KV-7800PF-J L=20C416 2303-001026 C-FILM,PPF;33nF,10%,400V,TP,20x15x8,7.5C417 2306-000102 C-FILM,MPPF;1.2uF,5%,250V,TP,29*31*14.5,20C418 2201-000556 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5C419 2401-001397 C-AL;470uF,20%,25V,GP,TP,10x16,5C421 2401-002619 C-AL;47uF,20%,25V,GP,TP,5x11,5C422 2306-000122 C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0mm,C423 2201-000556 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5C424 2401-001527 C-AL;47uF,20%,250V,HR,TP,13x25mm,5mC425 2305-000154 C-FILM,MPEF;100nF,5%,400V,TP,21.5x6.5x11.5C427 2201-000984 C-CERAMIC,DISC;680pF,10%,2KV,Y5P,TP,11x6,7.5mC504 2202-000862 C-CERAMIC,MLC-AXI;AL 390pF,10%,50V,Y5P,TP,3.5x1.9,-C506 2301-000213 C-FILM,PEF;220nF,5%,250V,TP,21.5x11,7.5C510 2401-000430 C-AL;10uF,20%,250V,GP,TP,10x16mm,5mC520 2401-001232 C-AL;4.7uF,20%,250V,GP,TP,10x12.5,5C530 2201-002063 C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,TP,16x5,7C601 2401-001914 C-AL;1uF,20%,50V,BP,TP,5x11,5C602 2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mmC603 2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5C604 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mmC605 2401-001914 C-AL;1uF,20%,50V,BP,TP,5x11,5C607 2401-001998 C-AL;1000uF,20%,25V,GP,TP,10x20,5mmC701 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C702 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5C703 2202-000243 C-CERAMIC,MLC-AXI;AL 33pF,5%,50V,SL,TP,3.5x19,-C704 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5C705 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mmC707 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5C709 2306-000122 C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0mm,C710 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5C711 2401-002235 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mmC712 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5C713 2301-000247 C-FILM,PEF;33nF,5%,50V,TP,8.1x4.5x13mm,5mC714 2301-000289 C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5C715 2401-000647 C-AL;2.2uF,20%,50V,BP,TP,5x11,5C716 2401-000647 C-AL;2.2uF,20%,50V,BP,TP,5x11,5C717 2301-000289 C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5C718 2301-000247 C-FILM,PEF;33nF,5%,50V,TP,8.1x4.5x13mm,5mC719 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5C720 2401-002235 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mmC721 2301-000175 C-FILM,PEF;15nF,5%,50V,TP,7.1x3.5x13mm,5mC722 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mmC723 2301-000175 C-FILM,PEF;15nF,5%,50V,TP,7.1x3.5x13mm,5mC725 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mmC727 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mmC730 2202-000231 C-CERAMIC,MLC-AXI;AL 330pF,10%,50V,Y5P,TP,3.5x19,-C731 2202-000231 C-CERAMIC,MLC-AXI;AL 330pF,10%,50V,Y5P,TP,3.5x19,-C801 2306-000321 C-FILM,MPPF;470NF,5%,275V,TP,-,22.5C802 2306-000321 C-FILM,MPPF;470NF,5%,275V,TP,-,22.5C804 2201-000332 C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7C805 2201-000332 C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7C806 2401-002227 C-AL;330uF,20%,450V,GP,BK,35x45,10C807 2303-000163 C-FILM,PPF;2.2nF,5%,800V,TP,15x13x8.5,7.5C808 2401-002292 C-AL;47uF,20%,25V,WT,TP,8X11,5C809 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5mC811 2301-000310 C-FILM,PEF;68nF,5%,50V,TP,8.0X8.5X4.0X5,5C812 2201-000990 C-CERAMIC,DISC;4.7nF,20%,400V,Y5U,BK,7x16,10m

Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

7. Electrical Parts List

C813 2201-000990 C-CERAMIC,DISC;4.7nF,20%,400V,Y5U,BK,7x16,10mC814 2201-000683 C-CERAMIC,DISC;850pF,10%,1KV,Y5P,TP,10x5,5C815 2401-001105 C-AL;330uF,20%,200V,GP,-,22x35mm,10C816 2401-000293 C-AL;100uF,+30-10%,200V,GP,TP,16x25C817 2201-000599 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5C818 2401-000722 C-AL;2200uF,20%,25V,WT,TP,16x25,7.5C819 2201-000599 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5C820 2401-000722 C-AL;2200uF,20%,25V,WT,TP,16x25,7.5C821 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mmC822 2201-000599 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5C823 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5C824 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mmC825 2306-000122 C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0mm,C826 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5C827 2401-002235 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mmC828 2401-000493 C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mmC829 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5C830 2401-000611 C-AL;1uF,20%,50V,WT,TP,5x11,5C831 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5C832 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5C833 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5C835 2401-002286 C-AL;470uF,20%,16V,WT,TP,10x12.5,5C901 2201-000234 C-CERAMIC,DISC;150pF,5%,50V,CH,TP,9.5x3,5C902 2301-000108 C-FILM,PEF;1.5nF,5%,50V,TP,6.5x3.0x5.5mm,C903 2201-000119 C-CERAMIC,DISC;100nF,+80-20%,50V,Y5V,TP,8x3.5C904 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5C905 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,C906 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,C907 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C908 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C909 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C910 2202-000796 C-CERAMIC,MLC-AXI;AL 1NF,10%,50V,Y5P,TP,3.5X1.9MM,-C911 2202-000796 C-CERAMIC,MLC-AXI;AL 1NF,10%,50V,Y5P,TP,3.5X1.9MM,-C912 2202-000121 C-CERAMIC,MLC-AXI;AL 100pF,10%,50V,Y5P,TP,1.9x3.5,-C914 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,C915-J 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5C916 2201-000257 C-CERAMIC,DISC;16pF,5%,50V,CH,TP,5x3,5C917 2201-000483 C-CERAMIC,DISC;33pF,5%,50V,CH,TP,5x3,5C918 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mmC919 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C919HB 0403-000297 DIODE-ZENER;MTZ6.2B,6.2V,5.96-6.27V,500mW,C920 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5C921 2202-000796 C-CERAMIC,MLC-AXI;AL 1NF,10%,50V,Y5P,TP,3.5X1.9MM,-C922 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5C923 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C924 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5C925 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C926 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C927 2202-002037 C-CERAMIC,MLC-AXI;AL 100nF,80-20%,50V,Y5V,TP,2.2x3.C928 2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5CE01 2401-002597 C-AL;220uF,20%,35V,GP,TP,10x12.5,5CE02 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,CE03 2305-000470 C-FILM,MPEF;68nF,5%,100V,TP,-,5mmCLAMP 7022903017G CLAMP-CODE;BVM8.667.017CLAMPF AA65-30009A CLAMP-FBT;ABS,V0,BLK,-,-,-CLAMPF AA65-30109A CLAMP-FBT;NYLON-66,V2,BLK,-,-,-CN501B AA39-20604A LEAD CONNECTOR-AS;SY -,YBNH250-

09,YBNH05/04,5/4P,50CN602 3711-002644 CONNECTOR-HEADER;BOX,5P,1R,2.5mm,STRAIGHT,SNCN701 3711-002647 CONNECTOR-HEADER;BOX,8P,1R,2.5mm,STRAIGHT,SNCONNE 5401401523 CONNECTOR;L=50MMCORE 3301-001201 CORE-FERRITE;AE,230.5x10.25x36mm,1500,280GCW701 2503-000161 C-NETWORK;330pFx8,20%,50V,MCCB1H331MX8YTCW901 2503-000156 C-NETWORK;100pFx4,20%,50VD101 0401-001024 DIODE-SWITCHING;BAW75,25V,300mA,DO-35,TPD201 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD202 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD203 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD204 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD209 0402-000216 DIODE-RECTIFIER;ERC24-06,600V,1.0A,DO-204D210 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD217 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD301 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TPD302 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD303 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD304 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD401 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L,TP

D402 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TPD403 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TPD404 0402-001296 DIODE-RECTIFIER;FMP-3FU,1.5KV,5A,TO-3PF,STD406 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TPD407 0402-000216 DIODE-RECTIFIER;ERC24-06,600V,1.0A,DO-204D410 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L,TPD507 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TPD508 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TPD509 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TPD520 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TPD601 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW,D602 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD801 0402-000213 DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41,TPD802 0402-001160 DIODE-BRIDGE;D5SB60,600V,2.8A,SIP-4,STD803 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TPD804 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD805 0402-000231 DIODE-RECTIFIER;FMG-G26S,600V,4A,TO-220F,STD806 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L,TPD807 0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,- H/SINKD808 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TPD809 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD810 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD813 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L,TPD901 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD902 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD903 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD904 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD905 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD906 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD907 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPD-COIL AA65-30017A CLAMP-D,COIL;NYLON-66,V0,NTR,DADH300,25 20’DE01 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,TPDIODE 0403-001118 DIODE-ZENER;MTZ30A,32V,26.99-28.39V,500mW,DV801 1405-000152 VARISTOR;560V,2500A,14x8.5mm,TPDZ201 0403-000297 DIODE-ZENER;MTZ6.2B,6.2V,5.96-6.27V,500mW,DZ202 0403-000297 DIODE-ZENER;MTZ6.2B,6.2V,5.96-6.27V,500mW,DZ203 0403-000298 DIODE-ZENER;MTZ6.8C,6.8V,6.66-7.01V,500mW,DZ205 0403-000551 DIODE-ZENER;MTZ3.9B,3.9V,3.89-4.16V,500mW,DZ206 0403-000294 DIODE-ZENER;MTZ4.7B,4.7V,4.55-4.80V,500mW,DZ302 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW,DZ303 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW,DZ304 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW,DZ305 0403-000494 DIODE-ZENER;MTZ39,39V,35.36-37.2V,500mW,DODZ306 0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,TPDZ402 0403-000300 DIODE-ZENER;MTZ8.2B,8.2V,7.78-8.19V,500mW,DZ403 0403-000698 DIODE-ZENER;TZP12A,12V,11.4-12.6V,1W,DO-41DZ505 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW,DZ601 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW,DZ602 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW,DZ603 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW,DZ604 0403-000545 DIODE-ZENER;MTZ24B,24V,22.61-23.77V,500mW,DZ701 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW,DZ702 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW,DZ703 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW,DZ704 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW,DZ705 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW,DZ801 0403-000300 DIODE-ZENER;MTZ8.2B,8.2V,7.78-8.19V,500mW,DZ802 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW,DZ803 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW,DZ804 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW,DZ805 1203-001217 IC-POSI.ADJUST RE;G. 431,TO-92,3P,4.58MIL,PLASTIC,2DZ807 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW,DZ808 0403-000562 DIODE-ZENER;MTZ7.5B,7.5V,7.07-7.45V,500mW,DZ901 1203-000451 IC-VOLTAGE REGULA;TOR 33,TO-92,3P,-,PLASTIC,31/35V,2DZ904 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500mW,DZ905 0403-000296 DIODE-ZENER;MTZ5.6B,5.6V,5.45-5.73V,500mW,F801 5463010400 FUSE;RT1-20-4A/250VF801A 3602-000114 FUSE-HOLDER;-,-,30mohmF801B 3602-000114 FUSE-HOLDER;-,-,30mohmF802 3601-001086 FUSE-FERRULE;125V,5A,FA,GLASS,2.4x7.5mmF803 3601-001086 FUSE-FERRULE;125V,5A,FA,GLASS,2.4x7.5mmHC101 AA13-20004WIC-HYBRID;-,PAP103T,SIP,6P,PRE-AMP,TPIC201 1204-001480 IC-DEMODULATOR;TDA8843/N2,DIP,56P,-,PLASTIC,8IC301 1204-000517 IC-VERTIVAL DEF.;LA7845,SIP,7P,-,PLASTIC,40V,11 H/SINKIC501 1201-001330 IC-VIDEO AMP;6108,ZSIP,9P,-,SINGLE,-,PLASTI H/SINKIC601 1201-001064 IC-POWER AMP;7297,ZIP,15P,-,DUAL,32dB,PLAST H/SINKIC701 1204-000473 IC-AUDIO PROCESSO;R TDA9859,DIP,32P,-,PLASTIC,-,-,




!

!!

!!!!!

IC801 1203-001482 IC-PWM CONTROLLER;3S1265R,TO-3P,5P,210,PLASTIC,6H/SINK

IC802 0604-001038 PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,STIC803 1203-001006 IC-VOLTAGE REGULA;TOR 78R05,TO-220F,4P,-,PLASTIC,4.8IC804 1203-000644 IC-POSI.FIXED REG;. 7630,SIP,10P,-,PLASTIC,5.1/8V,

H/SINKIC901 AA13-00038A IC-MCU;-,SZM-503CT(R4203),16BIT,SDIP,IC902 1103-001105 IC-EEPROM;24C040,4Kx1BIT,DIP,8P,300MIL,1ICE01 1201-000191 IC-OP AMP;4558,DIP,8P,300MIL,DUAL,20V/mVJ206 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400GJA701 3722-000503 JACK-RCA;9P,3.6mm,-,NIL101 2701-000326 INDUCTOR-AXIAL;560nH,10%,2.3x3.4mmL102 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL103 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL202 2701-000197 INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mmL203 2701-000197 INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mmL205 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL206 2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mmL208 2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mmL303 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL401 AA27-40003J COIL-HORIZ,WIDTH;-,3mH,ER14 20,PI0.35,STL402 5447130012 COIL- LINEARITY;AC0012L403 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400GL404 AA27-00038A COIL-HORIZ. WIDTH;-,700UH,15X27,-,BKL501 2901-000297 FILTER-EMI ON BOA;RD -,3A,-,-,3.5x5,TP,-L601 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400GL603 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400GL703 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL704 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL705 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL706 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL707 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL708 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL709 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL801 AA29-30002F FILTER-LINE NOISE;-,6mH,2.45A,-,-L802 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400GL803 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400GL804 2901-000299 FILTER-EMI ON BOA;RD -,6A,UL/CSA,-,9x7.5,TP,-L805 2701-001032 INDUCTOR-AXIAL;100UH,10%,5X14MML806 2901-000297 FILTER-EMI ON BOA;RD -,3A,-,-,3.5x5,TP,-L807 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400GL808 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,2400GL901 2701-000189 INDUCTOR-AXIAL;470nH,10%,2.5x3.4mmL902 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL903 2701-000197 INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mmL904 2701-000211 INDUCTOR-AXIAL;68uH,10%,2.5x3.4mmL905 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL906 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmL907 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmLD901 AA96-30001B ASSY-LED,GUIDE;-,AA61-50055A,DL-G5RGA,-POWCO 5424020002A POWER CODE(PLUG);RVVB-2P-C2169Q101 0501-000245 TR-SMALL SIGNAL;BC548C,NPN,500mW,TO-92,TP,420-Q201 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q202 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q204 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q205 0504-000150 TR-DIGITAL;KSR2010,PNP,300mW,10K,TO-92,TPQ206 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TPQ207 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q210 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q301 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q302 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q401 0502-000298 TR-POWER;KSD73,NPN,30W,TO-220,-,120-240 H/SINKQ402 0502-001007 TR-POWER;KSC2073-H2,NPN,25W,TO-220,ST,6Q403 0502-001136 TR-POWER;KSD5703,NPN,70W,TO-3PF,ST,8- H/SINKQ701 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q702 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q801 0501-000369 TR-SMALL SIGNAL;KSC2331-Y,NPN,1W,TO-92L,-,120-Q901 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q902 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TPQ903 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TPQ904 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TPQ905 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q906 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,120-Q907 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q908 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-Q909 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,TP,120-QE01 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,120-

R102 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR103 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR104 2001-000674 R-CARBON;360OHM,5%,1/8W,AA,TP,1.8X3.2MMR105 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR201 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR202 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR203 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR204 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR212 2001-000005 R-CARBON;390ohm,5%,1/8W,AA,TP,1.8x3.2mmR214 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MMR215 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MMR217 2001-000343 R-CARBON;130OHM,5%,1/8W,AA,TP,1.8X3.2MMR218 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MMR219 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MMR220 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR221 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR222 2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mmR223 2001-000617 R-CARBON;3.9MOHM,5%,1/8W,AA,TP,1.8X3.2MR224 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR225 2001-001026 R-CARBON;910OHM,5%,1/8W,AA,TP,1.8X3.2MMR226 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MMR230 2001-000331 R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MMR231 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MR232 2001-000241 R-CARBON;1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MR233 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MMR234 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MMR235 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MMR237 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MMR238 2001-001113 R-CARBON(S);270KOHM,5%,1/2W,AA,TP,2.4X6.4MR239 2001-000008 R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MMR241 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR246 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MR247 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR248 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MMR249 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR250 2001-000938 R-CARBON;68OHM,5%,1/8W,AA,TP,1.8X3.2MMR251 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR252 2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MMR253 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MR255 2001-000008 R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MMR256 2004-001234 R-METAL;75Kohm,5%,1/8W,AA,TP,1.8x3.2mmR257 2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MMR258 2004-001914 R-METAL;39Kohm,2%,1/8W,AA,TP,1.8x3.5mmR259 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR260 2001-001015 R-CARBON;9.1KOHM,5%,1/8W,AA,TP,1.8X3.2MR261 2001-000331 R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MMR262 2001-001015 R-CARBON;9.1KOHM,5%,1/8W,AA,TP,1.8X3.2MR301 2001-001045 R-CARBON(S);1.2KOHM,5%,1/2W,AA,TP,2.4X6.4MR302 2001-001049 R-CARBON(S);1.3KOHM,5%,1/2W,AA,TP,2.4X6.4MR303 2001-000016 R-CARBON(S);1OHM,5%,1/2W,AA,TP,2.4X6.4MMR304 2008-000254 R-FUSIBLE(S);0.68ohm,5%,2W,AF,TP,3.9x10mmR305 2003-002009 R-METAL OXIDE(S);390ohm,5%,2W,AF,TP,3.9x10mmR306 2003-002009 R-METAL OXIDE(S);390ohm,5%,2W,AF,TP,3.9x10mmR308 2003-002009 R-METAL OXIDE(S);390ohm,5%,2W,AF,TP,3.9x10mmR309 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR310 2001-000387 R-CARBON;16KOHM,5%,1/8W,AA,TP,1.8X3.2MMR311 2001-000660 R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MMR312 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR313 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR314 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR315 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR316 2001-000660 R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MMR317 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR404 2008-001013 R-FUSIBLE(S);1.2ohm,5%,2W,AF,TP,3.9x10mmR405 2001-001138 R-CARBON(S);390OHM,5%,1/2W,AA,TP,2.4X6.4MMR406 2003-002008 R-METAL OXIDE(S);18Kohm,5%,2W,AF,TP,3.9x10mmR407 2003-001025 R-METAL OXIDE(S);15Kohm,5%,2W,AF,TP,3.9x10mmR409 2008-000264 R-FUSIBLE(S);1ohm,5%,1W,AF,TP,3.9x10mmR410 2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4MMR411 2001-000022 R-CARBON(S);33OHM,5%,1/2W,AA,TP,2.4X6.4MMR412 2001-000020 R-CARBON(S);22OHM,5%,1/2W,AA,TP,2.4X6.4MMR413 2008-000266 R-FUSIBLE(S);1ohm,5%,2W,AF,TP,3.9x10mmR414 2008-000278 R-FUSIBLE(S);82ohm,5%,2W,AA,TP,3.9x10mmR415 2008-000266 R-FUSIBLE(S);1ohm,5%,2W,AF,TP,3.9x10mmR417 2001-001164 R-CARBON(S);56KOHM,5%,1/2W,AA,TP,2.4X6.4MMR418 2004-001967 R-METAL(S);68Kohm,1%,1/2W,AA,TP,2.5x6.5mmR419 2004-001390 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm




!

!!!

!!!

!!!

!

R420 2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4MMR421 2001-001043 R-CARBON(S);0OHM,5%,1/2W,AA,TP,2.4X6.4MMR422 2008-001013 R-FUSIBLE(S);1.2ohm,5%,2W,AF,TP,3.9x10mmR424 2001-001043 R-CARBON(S);0OHM,5%,1/2W,AA,TP,2.4X6.4MMR425 2001-001043 R-CARBON(S);0OHM,5%,1/2W,AA,TP,2.4X6.4MMR428 2001-001043 R-CARBON(S);0OHM,5%,1/2W,AA,TP,2.4X6.4MMR429 2001-001043 R-CARBON(S);0OHM,5%,1/2W,AA,TP,2.4X6.4MMR430 2001-001043 R-CARBON(S);0OHM,5%,1/2W,AA,TP,2.4X6.4MMR501 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR502 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR503 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR505 2008-000189 R-FUSIBLE;0.47ohm,10%,2W,AA,TP,6x15.5mmR506 2008-000299 R-FUSIBLE(S);47ohm,5%,2W,AF,TP,3.9x10mmR507 2001-000490 R-CARBON;200OHM,5%,1/8W,AA,TP,1.8X3.2MMR508 2001-000490 R-CARBON;200OHM,5%,1/8W,AA,TP,1.8X3.2MMR509 2001-000490 R-CARBON;200OHM,5%,1/8W,AA,TP,1.8X3.2MMR510 2002-001009 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0R517 2002-001009 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0R518 2002-001009 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0R519 2002-001009 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.7X9.0R520 2001-001062 R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2.4X6.4MMR601 2008-001002 R-FUSIBLE(S);0.18ohm,10%,2W,AA,TP,3.9x10mmR602 2008-001002 R-FUSIBLE(S);0.18ohm,10%,2W,AA,TP,3.9x10mmR603 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MR604 2001-000331 R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MMR605 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR606 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MR607 2001-000331 R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MMR701 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR702 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR703 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MMR704 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MMR705 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR706 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR707 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MMR708 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MMR709 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MMR712 2001-000539 R-CARBON;24KOHM,5%,1/8W,AA,TP,1.8X3.2MMR713 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MMR714 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR715 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MMR716 2001-000660 R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MMR717 2001-000539 R-CARBON;24KOHM,5%,1/8W,AA,TP,1.8X3.2MMR718 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MMR719 2001-000527 R-CARBON;22OHM,5%,1/8W,AA,TP,1.8X3.2MMR720 2001-000387 R-CARBON;16KOHM,5%,1/8W,AA,TP,1.8X3.2MMR721 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR722 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR723 2001-000387 R-CARBON;16KOHM,5%,1/8W,AA,TP,1.8X3.2MMR724 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR725 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MMR728 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR729 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR732 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR733 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MMR734 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MMR735 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MMR736 2001-000660 R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MMR740 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmR741 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmR801 2002-001011 R-COMPOSITION;3.3Mohm,5%,1/2W,AA,TP,3.7x9mmR802 2003-000994 R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x10mmR803 2003-000994 R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x10mmR804 2001-001150 R-CARBON(S);470KOHM,5%,1/2W,AA,TP,2.4X6.4MR805 2001-001150 R-CARBON(S);470KOHM,5%,1/2W,AA,TP,2.4X6.4MR806 2003-001023 R-METAL OXIDE(S);120ohm,5%,2W,AF,TP,3.9x10mmR807 2001-001178 R-CARBON(S);680OHM,5%,1/2W,AA,TP,2.4X6.4MMR808 2002-001011 R-COMPOSITION;3.3Mohm,5%,1/2W,AA,TP,3.7x9mmR809 2002-001013 R-COMPOSITION;4.7Mohm,5%,1/2W,AA,TP,3.7x9mmR810 2003-000783 R-METAL OXIDE(S);7.5Kohm,5%,2W,AC,BK,4x12mmR811 2003-001013 R-METAL OXIDE(S);10Kohm,5%,2W,AC,BK,4x12mmR813 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR814 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR815 2004-001889 R-METAL(S);127Kohm,1%,1/2W,AA,TP,2.5x6.5mR816 2004-001983 R-METAL(S);2.49Kohm,1%,1/2W,AA,TP,2.4x6.4R817 2001-001153 R-CARBON(S);47OHM,5%,1/2W,AA,TP,2.4X6.4MMR818 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM

R819 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MR820 2008-001047 R-FUSIBLE(S);68ohm,5%,2W,AF,TP,3.9x10mmR821 2008-000271 R-FUSIBLE(S);3.3ohm,5%,2W,AA,TP,3.9x10mmR822 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR823 2008-000264 R-FUSIBLE(S);1ohm,5%,1W,AF,TP,3.9x10mmR824 2001-001125 R-CARBON(S);300KOHM,5%,1/2W,AA,TP,2.4X6.4MR826 2001-001153 R-CARBON(S);47OHM,5%,1/2W,AA,TP,2.4X6.4MMR901 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR902 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR903 2001-000066 R-CARBON(S);10KOHM,5%,1/2W,AA,TP,2.4X6.4MMR904 2004-000218 R-METAL;10Kohm,1%,1/8W,AA,TP,1.8x3.2mmR905 2004-000218 R-METAL;10Kohm,1%,1/8W,AA,TP,1.8x3.2mmR906 2004-000218 R-METAL;10Kohm,1%,1/8W,AA,TP,1.8x3.2mmR907 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR908 2001-000241 R-CARBON;1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MR909 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MR910 2001-000924 R-CARBON;680OHM,5%,1/8W,AA,TP,1.8X3.2MMR911 2001-000214 R-CARBON;1.1KOHM,5%,1/8W,AA,TP,1.8X3.2MR912 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR913 2001-000241 R-CARBON;1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MR914 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MR918 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MR919 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR920 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MR921 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR922 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR923 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR924 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MR925 2001-000924 R-CARBON;680OHM,5%,1/8W,AA,TP,1.8X3.2MMR926 2001-000924 R-CARBON;680OHM,5%,1/8W,AA,TP,1.8X3.2MMR927 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmR928 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmR929 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mmR930 2001-000628 R-CARBON;300OHM,5%,1/8W,AA,TP,1.8X3.2MMR931 2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4MMR932 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MMR933 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR934 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR935 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MMR936 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR937 2001-001062 R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2.4X6.4MMR938 2001-000832 R-CARBON;510OHM,5%,1/8W,AA,TP,1.8X3.2MMR939 2001-000397 R-CARBON;180KOHM,5%,1/8W,AA,TP,1.8X3.2MR940 2001-001062 R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2.4X6.4MMR941 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MR942 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR943 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MMR945 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MR948 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR951 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MR953 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR954 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MMR955 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMRE01 2004-001390 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mmRE02 2004-001914 R-METAL;39Kohm,2%,1/8W,AA,TP,1.8x3.5mmRE03 2001-000066 R-CARBON(S);10KOHM,5%,1/2W,AA,TP,2.4X6.4MMRE04 2001-000066 R-CARBON(S);10KOHM,5%,1/2W,AA,TP,2.4X6.4MMRE05 2001-000052 R-CARBON(S);3.3KOHM,5%,1/2W,AA,TP,2.4X6.4MRE06 2004-001390 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mmRE07 2003-002037 R-METAL OXIDE(S);270ohm,5%,2W,AF,TP,3.9x10mmRE08 2001-001120 R-CARBON(S);3.3OHM,5%,1/2W,AA,TP,2.4X6.4MMRE09 2001-001125 R-CARBON(S);300KOHM,5%,1/2W,AA,TP,2.4X6.4MRE10 2001-001125 R-CARBON(S);300KOHM,5%,1/2W,AA,TP,2.4X6.4MRL801 3501-001040 RELAY-POWER;12VDC,500mW,10A,1FormA,15mS,5mRM901 AA59-60001U MODULE-REMOCON;-,ORC-50VF/SR-12V,38KHz,940nm,RP802 1404-001045 THERMISTOR-NTC;4.7ohm,15%,2900K,35.0mW,TPRP803 1404-001087 THERMISTOR-PTC;7ohm,30%,220V,270V,19A,-,STSF101 2904-001143 FILTER-SAW AV;38.9MHz,SIP5K,TP,16.5dB,B/G,L/SW801 3403-000179 SWITCH-PUSH;250V,5A,DPST,-,JPW-2104BSW901 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SPSTSW902 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SPSTSW903 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SPSTSW904 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SPSTSW905 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SPSTT401 AA26-50001R TRANS-HORIZ DRIVE;-,80MH,520UH,4UH,G11A EI19,STT444 AA26-30005Q TRANS-FLYBACK;-,FUH-29A001(S),29/25’,130VT801 AA26-20007WTRANS-SWITCHING;-,90~260V,130/15.5/12/8V,VDE,S




!!!

TU101 AA40-10006H TUNER-V/S;TELE4-108A,PAL-B/G,TR,181CHV999 3704-001105 SOCKET-CRT;11P,20PI,26.5PI,NI,-WIRE AA65-30018A CLAMP-WIRE;NYLON-66,-,-,DATL-600,DONG-A,-WIRE AA65-30105B CLAMP-WIRE;NYLON 66,V2,NTR,25MM,ALL MODELX202 2801-000274 CRYSTAL-UNIT;4.433619MHz,30ppm,28-AAM,20pF,X203 2801-000226 CRYSTAL-UNIT;3.579545MHz,20ppm,28-AAM,15pF,X901 2801-003224 CRYSTAL-UNIT;32.768KHz,20ppm,28-AAY,12.5pF,Z207 2903-000129 FILTER-CERAMIC;TR,4.5M/4.72MHZ,-,-,-,TP,-Z208 2903-000181 FILTER-CERAMIC;TR,5.5MHz,-,-,-,TP,TPS5.5MB-TF

ASSY-CRT

CRT 6126817402 29CRT;A68QBT892X(TSDD)D-COIL 5402922015-4 D-COIL;BRE4.799.015-3AD-COIL 7020100001 D-COIL-CLAMP;JG8.688.002

A1SSY CABINET FRONT

* AA92T30001D A1SSY CABINET FRONT;294C

BADGE AA64-70117B BADGE-BRAND;AL,SS,SILVER,L65,R2000,-,-BOSS AA61-40010A BOSS-WING;,HIPS,HB,NTR,-,-CONWIR 54029023611 CONNECTOR-WIRE;2LG3.568.3611COPPER 7013010060 CLAMP-COPPER;6CORE AA65-30008A CLAMP-CORD;PE,HB,BLK,-,-,-FRONT AA64-31086A CABINET-FRONT;-,294C,-,HIPS,HB,BLK,-,-GUM AA63-60004G SPACER-GUM,CRT;NTR RUBBER,T3.0,GRY,-,-,-HOLDCO AA61-20284A HOLDER;-,P-CORD,PP,VO,BLK,KE-002INLAY AA64-60366L INLAY-AV;5099.5399,KSP213 EG PAL S/T,PSKNOCON AA64-10702A KNOB-CONTROL;-,294C,-,ABS,HB,BLKPCB AA61-40053A STOPPER-PCB;ALL MODEL,HIPS HB,WHT,HB,-,-SCREW 4901031165 TAP SCREW;ST4*16+E25SJ2831-87 SCREW 4901031460 TAP SCREW;ST4*16FT-D.ZN.DJ SJ2831-87SCREW 4901031460 TAP SCREW;ST4*16FT-D.ZN.DJ SJ2831-87SCREW 4901031460 TAP SCREW;ST4*16FT-D.ZN.DJ SJ2831-87SCREW 4901031460 TAP SCREW;ST4*16FT-D.ZN.DJ SJ2831-87SCREW 4901033412 TAP SCREW;ST4X12 VWTSPRING 4901301024 SPRING;8.380.024WIRE AA65-30105B CLAMP-WIRE;NYLON 66,V2,NTR,25MM,ALL MODELWIRE AA65-30018A CLAMP-WIRE;NYLON-66,-,-,DATL-600,DONG-A,-

A1SSY CABINET-BACK

* AA92T40001I A1SSY CABINET-BACK;294C

BACK AA64-31087A CABINET-BACK;-,294C,-,HIPS,V0,BLK,-,-BACK 215298020 CABINET-BACK,LABEL;BKS8.805.095INLAY AA64-60233J INLAY-BACK;S51A,CHINA 9PIN,PS,T0.5,BLK,-,

A`SSY CONTROL DOOR

* AA92T60001C A`SSY CONTROL DOOR;CS-298CV

COVER AA63-30204A COVER-CONTROL;-,294C,-,HIPS,HB,BLK,-,-INDILED AA64-40391B INDICATOR-LED;-,99,-,ACRYL,-,CLEAR,-KNOPOW AA64-10606B KNOB-POWER;-,50.5399,MASTER,ABS,HB,M/BSPRING AA61-60003J SPRING-CS;-,SUS304,0.5,OD6,H12,N7,-,-,-WINRMC AA64-40390A WINDOW-REMOCON;-,99,-,ABS,HB,LG41338,-

ASSY-SOUND

* AA95-00380A ASSY-SOUND;-,CS-298CV,S51A,PAL,MONO,-

CFM01 2904-001054 FILTER-SAW AV;38.9MHz,SIP5P,-,13.9dB,NTSC-M/CFM02 2904-001010 FILTER-SAW AV;32.9~33.4MHz,SIP5P,ST,14.4dB,PCM01 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mmCM02 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5CM03 2401-002300 C-AL;47uF,20%,50V,GP,TP,6.3x11,5

CM04 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm,CM05 2202-000127 C-CERAMIC,MLC-AXI;AL 10nF,+80-20%,25V,Y5V,TP,-,7.5CM06 2202-000127 C-CERAMIC,MLC-AXI;AL 10nF,+80-20%,25V,Y5V,TP,-,7.5CM07 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5mCM08 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mmCM09 2202-000127 C-CERAMIC,MLC-AXI;AL 10nF,+80-20%,25V,Y5V,TP,-,7.5CM10 2202-000127 C-CERAMIC,MLC-AXI;AL 10nF,+80-20%,25V,Y5V,TP,-,7.5CM11 2202-000127 C-CERAMIC,MLC-AXI;AL 10nF,+80-20%,25V,Y5V,TP,-,7.5CM12 2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5CM13 2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5CM14 2401-000660 C-AL;2.2uF,20%,50V,GP,TP,5x11,5CM15 2401-000660 C-AL;2.2uF,20%,50V,GP,TP,5x11,5CM16 2401-000660 C-AL;2.2uF,20%,50V,GP,TP,5x11,5CM17 2401-000660 C-AL;2.2uF,20%,50V,GP,TP,5x11,5CM19 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mmCNN01 3711-002704 CONNECTOR-HEADER;NOWALL,6P,1R,2.5mm,ANGLE,SNCNN02 3711-002705 CONNECTOR-HEADER;NOWALL,7P,1R,2.5mm,ANGLE,SNDM01 0401-001024 DIODE-SWITCHING;BAW75,25V,300mA,DO-35,TPDM02 0401-001024 DIODE-SWITCHING;BAW75,25V,300mA,DO-35,TPDM03 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPDM04 0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,TPHN01 AA61-10068A BRACKET-PCB;-,M2160,SPTE,T0.3,-,-,-ICM01 1204-001491 A;LA7566S,DIP,24P,300MIL,PLASTICLM02 2701-000168 INDUCTOR-AXIAL;3.3uH,5%,2.5x3.4mmPCB AA41-11018B PCB-MONO;S51A,1L,CS29D9,245X245X1.6T,9AQM01 0504-000125 TR-DIGITAL;KSR1012,NPN,300mW,47K,TO-92,TPQM02 0504-000125 TR-DIGITAL;KSR1012,NPN,300mW,47K,TO-92,TPQM03 0504-000125 TR-DIGITAL;KSR1012,NPN,300mW,47K,TO-92,TPQM04 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TPQM05 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TPQM06 0504-000123 TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,TPQM07 0504-000119 TR-DIGITAL;KSR1004,NPN,300MW,47K/47K,TO-9QM08 0504-000119 TR-DIGITAL;KSR1004,NPN,300MW,47K/47K,TO-9QM09 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,120-RM01 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MMRM02 2001-000362 R-CARBON;150OHM,5%,1/8W,AA,TP,1.8X3.2MMRM03 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MRM04 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MRM05 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MRM06 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MMRM09 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MMRM10 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MMRM11 2001-000003 R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mmRM12 2001-000003 R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mmRM13 2001-000003 R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mmRM14 2001-000003 R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mmRM15 2001-000857 R-CARBON;560OHM,5%,1/8W,AA,TP,1.8X3.2MMRM16 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MRM17 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MRM18 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MRM19 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MRM20 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MRM21 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MRM22 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MRM23 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MRM24 2001-000008 R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MMRM25 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MRM27 2001-000832 R-CARBON;510OHM,5%,1/8W,AA,TP,1.8X3.2MMRM28 2001-000832 R-CARBON;510OHM,5%,1/8W,AA,TP,1.8X3.2MMTM01 AA26-10006L TRANS-IF;-,7MG,VIF,-,7mm,39pF,38.9MHz,SZM01 2903-000200 FILTER-CERAMIC;BP,6.5MHz,+-70KHz,6dB,-,TP,-ZM02 2903-000277 FILTER-CERAMIC;BP,6.0MHz,60KHz,6.0dB,-,TP,-ZM03 2903-000185 FILTER-CERAMIC;BP,5.5MHz,+-75KHz,6dB,-,TP,-ZM04 2903-000135 FILTER-CERAMIC;BP,4.5MHz,+-60KHz,6dB,-,TP,-

ASSY—PCB,A/V FRO;NT

* AA95T30001C ASSY—PCB,A/V FRO;NT S51A

CA04 2202-000720 C-CERAMIC,MLC-AXI;AL 8.2nF,20%,16V,Y5R,TP,3.5x19,-CA05 2202-000720 C-CERAMIC,MLC-AXI;AL 8.2nF,20%,16V,Y5R,TP,3.5x19,-CA06 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5CA07 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5CN01A AA39-20068E LEAD-CONNECTOR,AS;SY -,YBNH025-08,67096-008,8P,500,CN05A AA39-20069A LEAD-CONNECTOR,AS;SY -,YBNH025-05,67096-005,5P,500,




!!

!

CN06A AA39-20499B LEAD CONNECTOR-AS;SY -,YBNH025-04,SMP025-04,4P,200,

JE01 3722-000143 JACK-PHONE;1P(VER),3.4mm,AG,BLK,NOJR01 3722-001031 JACK-RCA;3P,3.6mm,#18,AULA04 2701-000180 INDUCTOR-AXIAL;33uH,5%,2.5x3.4mmLA05 2701-000180 INDUCTOR-AXIAL;33uH,5%,2.5x3.4mmPCB AA41-10620A PCB-AV;SCT12A,1L,FR-1,245x245x1.6T,A1RA01 2001-000028 R-CARBON(S);100OHM,5%,1/2W,AA,TP,2.4X6.4MMRA02 2001-000028 R-CARBON(S);100OHM,5%,1/2W,AA,TP,2.4X6.4MM

A1SSY SPEAKER

* AA96T10001C A1SSY SPEAKER;294C

HOSPK 7022903002G HOLDER SPEAKER;JG7.013.002LEADCO AA39-20504F LEAD CONNECTOR-AS;SY -,SMH025-

04,REC,4P,400,800mm,1SCREW 4901031425 TAP SCREW;ST4X12 SJ2831-87SPKER 3001-000151 SPEAKER;20W,8ohm,92dB,110Hz

ASSY ACCESSORY

BATTY 2130705050 BATTERY;5#I/B 21530A9010 USERS-MANUAL;CS-30A9I/B 2160402110 USERS MANUAL SHEET;BKS8.840.003(350*260*0.03)REMCO AA59-10117E REMOCON;DP,TM59,-,AA59-10116E,-,-,-,-,




8. Block Diagram

8-1 S51A

Block Diagram


FREE-AMPPAP103

VIF SAW FILTERK7257M

1 CHIPIF/VIDEO/CHROMA/DEFLECTION

TDA8844

EEPROMX24C04P

AC INPUTAC230V OR 100~260V

SMPS

TRANS

CRT

SZM-XXXMRIC

MCU

RGB-AMPTDA6108

TUNERTELE4-108A

TTXDECODERSAA5261

FBT

FUH-29A001

VERTICAL AMPLA7845

H-OUT TR

STRKA3S1265R

KA7630

HEATER

V H

HV

+16.5V / -14V

16.5V

220V

5V

8V

15V

130V

SIF SAW FILTER TDA9808SIF-DETECTOR

TDA9874NICAM

DECODERTDA9859 TDA7297

SPEAKER8W 10W X 2

AUDIO-PROCESSOR

2CH AUDIO AMP

AUDIO-MODULE

PIP-DECODERSDA9288/TDA9160A

9. PCB Layout

9-1 PCB Main

PCB Layout


D101 78 236D201 171 131D202 168 131D203 166 131D204 163 139D205 155 226D206 125 167D209 112 164D210 127 148D217 30 238D301 105 131D302 124 104D303 105 84D304 97 121D401 114 67D402 128 126D403 70 109D404 89 28D405 106 148D406 37 109D407 20 76D410 10 86D507 312 223D508 312 220D509 312 216D520 268 225D601 214 205D602 223 200D603 223 198D701 172 210D801 246 31D802 255 60D803 230 37D804 228 31D805 173 22D806 168 39D807 156 63D808 269 92D809 187 122D810 183 132D812 160 70D813 167 100D901 231 138D902 188 143D903 188 140D904 188 138D905 199 161D906 229 124D907 227 124DE01 94 108DL201 155 206DT01 260 120DT02 242 116DT03 201 161DT04 223 128DV801 264 7DV802 251 7DX01 19 8DX02 60 7DZ201 142 197DZ202 106 218DZ203 155 120DZ204 158 229DZ205 125 148DZ206 121 170DZ210 109 148DZ302 107 121DZ303 99 108DZ304 102 131DZ305 94 133DZ306 118 135DZ402 90 91DZ403 75 165DZ501 309 190DZ502 316 190

DZ503 296 190DZ505 321 190DZ601 223 213DZ602 223 215DZ603 223 223DZ604 223 220DZ701 49 148DZ702 54 148DZ703 59 148DZ704 41 141DZ705 64 148DZ801 231 33DZ802 218 26DZ803 150 122DZ804 177 120DZ805 183 12DZ807 166 120DZ808 209 19DZ901 227 165DZ904 211 145DZ905 280 108DZ906 321 82DZX01 39 13

HC101 60 224IC201 85 198IC301 123 132IC501 315 178IC601 238 185IC701 17 190IC801 245 9IC802 201 19IC803 201 95IC804 148 127IC901 267 134IC902 274 105IC903 193 120ICE01 130 118

Q101 71 213Q201 159 131Q202 149 132Q204 87 230Q205 139 219Q206 133 219Q207 146 219Q209 146 172Q210 121 183Q211 196 182Q212 199 193Q301 119 91Q302 111 96Q401 143 74Q402 83 130Q403 43 97Q404 83 134Q701 54 162Q702 54 182Q704 183 215Q801 293 97Q901 240 163Q902 251 234Q903 251 222Q904 251 215Q905 246 148Q906 204 150Q907 231 128Q908 227 128Q909 155 230QE01 140 96QT01 201 127QT02 245 139QX01 43 8

Loc. No. X Y

DIODE

IC

Loc. No. X Y

TRANSISTOR

X

Y

10. Wiring Diagram

10-1 S51A

Wiring Diagram


FOCUSSW801

MI

COM

S O U NDA MP

CN602P IP /T T XMO D U L E

TDA8844

TUNER

AUDI

O

MODULE

CN701

CN502

CN401

S MP ST R ANS

CN501

CN501B

A S S Y -P W B M A IN

C R T

ANODE

DY

SCR EEN

SOCKETCRT

F B T

CN01A

CN07A CN06A

CN05A

WOOF ER

R

L

A S S Y -P W B

S ID E


MEMO

51

50

1

2

3

8

4 5

6

7

10

9

11

12

Schematic Diagrams

11-1Samsung Electronics

11. Schematic Diagrams

11-1 MAIN (Power)

: Power Line: Signal Line

1 2

3 4

5 6

7 8

9 10

11 1250 51

Schematic Diagrams


11-2 PWB MAIN (One-Chip)

13

14

1516

1718

19

20

21

22

23 24

252627

28

29

30

31

32


24232526272829303132

2221

2019

1817

1615

1413

Schematic Diagrams


11-3 PWB MAIN / CRT (u-COM)

33 42

4041

39

37

3638

34

35

43

45

44


33 34

35 36

37 38

40 41

42 43

44 45

39

Schematic Diagrams


46

47

48

49

11-4 PWB MAIN (SUB)


46

47

48

49

Schematic Diagrams


11-5 PWB MAIN (Sound Module)

Schematic Diagrams


11-6 MICOM ( TTX ) / A/V SIDE

Schematic Diagrams


11-7 PWB MAIN (SOUND MODULE STEREO)

Schematic Diagrams


11-8 PWB MAIN (SOUND MODULE NICAM)

Schematic Diagrams


11-9 PWB MAIN (PIP-TTX)

Schematic Diagrams


11-10 PWB MAIN (PIP)

color television receiver - go-gddq. · pdf filecolor television receiver chassis : s51a model...

Documents