citroËn / peugeot / vauxhall electric wiring kit for

1/16

CITROËN / PEUGEOT / VAUXHALL

Set up trailer operation

The light functions on the trailer will only operate AFTER the vehicle has been re-coded!

!

Electric wiring kit for towbars / 7-pin / 12N / 12 Volt / ISO 1724

This electric kit has to be installed by a professional workshop or a suitable qualified person.The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance!Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! Also please check that there is a definite compatibility between this vehicle and the electric kit!Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update).All warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected.If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted.This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment!Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle’s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system.Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module.We always recommend whenever possible, the following troubleshooting process: An analysis of the vehicle’s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module from the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team!Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. All of the data and illustrations may not be an exact representation but the text contained in this instruction must be observed!

Part No: PE-084-07MU

Revision: 7 / 03.02.2021PE-084-07MU

ECS Electronics UK20 Speedwell Close Hun�ngtonChester, CH3 6DX

Email-sales: [email protected]: [email protected]

SALE: +44 (0) 7590 564639TECHNICAL: +44 (0) 7440 202052WEB: www.ecs-electronicsuk.co.uk

[email protected]

www.ecs-electronicsuk.co.uk

C5 AircrossC5 Aircross Hybrid300830083008 HYbrid

01/2019 >>08/2020 >>10/2016 >> 12/202001/2021 >>01/2020 >>

50085008Grandland XGrandland X Hybrid

03/2017 >> 12/202001/2021 >>10/2017 >>01/2020 >>

2/16

16-23

9-1524-2627-29

3x

3x3x 1x3x 3x

10x

M

X

B

U

M

A

G

C1

C2

K

1x 3x20

Amp.

20 Amp.

1x

20 Amp.minifuse

20 Amp. 1x1x

U4 U3

1x 1x

U1 U2

Revision: 7 / 03.02.2021PE-084-07MU




Part No: **-***-***

Electric wiring kit for towbars / 13-pin / 12 Volt / ISO 11446

This electric kit has to be installed by a professional workshop or a suitable qualified person.The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance!Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! Also please check that there is a definite compatibility between this vehicle and the electric kit!Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update).All warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected.If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted.This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment!Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle’s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system.Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module.We always recommend whenever possible, the following troubleshooting process: An analysis of the vehicle’s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module form the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team!Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. All of the data and illustrations may not be an exact representation but the text contained in this instructions must be observed!

Product overview

[email protected]


Revision: X / XX.XX.XXXXXX-XXX-XXX




3/16

SYMBOL EXPLANATION

TOOLS

Left (58-L) respectivelyRight (58-R) tail light

Stop light (54) / high mounted, third stop light (54)

Turn signal indicator left

Turn signal indicator right

Rear fog light(s)

Reversing light(s)

Trailer / trailer recognition

Permanent current power supply

Ground or Earth (31)

Ground connection battery terminal lug

Permanent power supply / 13pin socket, chamber 9

Charging wire for trailer battery / 13pin socket, chamber 10

+

15+

+

30+

Positive connection battery terminal lug

54 STOP

L

R

Reverse

B+/30

Fuse / fuse capacity 20 Ampère

Cigarette lighter /accessory socket

Loudspeaker / buzzer

Park Distance Control

Switch / source of function

Connect together

Disconnect

Look at / See further information

Look carefully at selected area

Present / Occupied / OK

Not present / Not occupied / Not OK

Acoustic indication

Attention / important advice

20 Amp.

20 Amp.

12V

ATTENTION! In order to avoid mal-functions and damage to the vehicle’s electrical system the earth terminal must be disconnected from the vehicle’s battery before starting work!

Both the trailer module and the vehicle’s control unit for the electrical system can be damaged during workon the data bus connections if the battery is not disconnected!

Please pay attention to the manufacturer’s instructions when disconnecting and reconnecting the vehicle’s battery!

!Code

3:3

Note: It may be necessaryto check if this vehicle hasa stored radio code beforedisconnecting the battery!

1

ATTENTION! The vehicle's cooling capacity may have to be increased when retrofitting a trailer coupling!You must observe the manufacturer's instructions!!

Co

Co

Revision: 7 / 03.02.2021PE-084-07MU




4/16

Revision: 7 / 03.02.2021PE-084-07MU




2

C5 Aircross/ C5 Aircross Hybrid/ 3008/ Grandland X

4


4x

1

3


3

2x1

5

4 2

3

2

! Only C5 Aircross Hybrid

1

4

5

3

2

5/16

5

5008

7

All models

5008

6

1

2

3

1

2

1

2

Revision: 7 / 03.02.2021PE-084-07MU




6/16

8

All models

9

All models

1

2

3

X

1

2

SEAL WITH SILICONE.

3

Revision: 7 / 03.02.2021PE-084-07MU




7/16

10

13

11

12

Option 1 Option 2

X X

SOCKET CONNECTION

1-7 STOP

21W21W 21W 42W 3x21W 42W

DIN/ISO 1724

Pmax

Yellow Blue White Green Brown Red Black

1/L 2 3/31 4/R 5/58-R 6/54 7/58-L

L R

Option 1

!

!

X

Revision: 7 / 03.02.2021PE-084-07MU




8/16

Important! Please note informations

in picture 1!17

3008/ Grandland X

M

14

15

16

M

M

M

1 2 3

4

Option 2 1 2 3

Option 2 1 2 3

Revision: 7 / 03.02.2021PE-084-07MU




Black22-pin

B

B

54 STOP

54 STOP

Blue/Red1 2

3 4

B

54 STOP

Pos. 8

Pos. 8

9/16

18

3008/ Grandland X

3008/ Grandland X

19

20

C5 Aircross/ C5 Aircross Hybrid

10 mm 1

2

G

54 STOP

1 2

Pos.1

54 STOP

B

Blue/Red

Pos.1B

Pos.1

316-pin Black

Revision: 7 / 03.02.2021PE-084-07MU




10/16

21

5008/ C5 Aircross/ C5 Aircross Hybrid

Important! Please note informations

in picture 1!

M

22


22-pin

B

B

54 STOP

54 STOP

Blue/Red1 2

3 4

B

54 STOP

Pos. 8

Pos. 8

Revision: 7 / 03.02.2021PE-084-07MU




11/16

23


24

All models

10 mm

G

1

2

AC2

Revision: 7 / 03.02.2021PE-084-07MU




All models

All models

12/16

25

26

1

2

3

1

2

Option 1

Option 2

3

B+/30

B+/30

1

2 3

Red

Red Red

U1

Red

A

A

A

A A

27

Option 3

Black1-pin

orB+/30

Grandland X3008

Revision: 7 / 03.02.2021PE-084-07MU




13/16

27

28

29

Option 1

Option 2

C2

Red/Blue

20 Amp.

20 Amp.20

Amp.

20 Amp.

U

Red/BlueRed

Option 3

Grandland X3008

Important!Please do not mountthe fuse tap and its

wiring output inthe otherdirection!

!

U2 U33

12V

Pos. 14/16/17/19=

Choose free position

+30

U4

20 A

mp

20 A

mp

1

2

Revision: 7 / 03.02.2021PE-084-07MU




14/16

30

32

! Code3:3

Set up trailer operation

!Vauxhall Grandland X

TIS2Web

VCI-Code Multiple

Diagnostic

Interface

The activation of the trailer functions

has to be carried out using theCITROËN/PEUGEOT DIAGBOX as follows:

• choose vehicle• delivery• equipment• trailer control unit (BSR)• installation of equipment

has to be carried out using theVAUXHALL TIS 2 WEB SPS as follows:

The activation of the trailer functions

• choose vehicle• Z6 change vehicle options

> add Trailer Hitch> normal

• start installation

31

Reverse

! MAX = 21W

12S socket

Reverse

Reverse

Pink

K

KG

Optional

!Citroen C5 Aircross

Peugeot 3008

Peugeot 5008

Citroen C5 Aircross Hybrid

Revision: 7 / 03.02.2021PE-084-07MU




15/16

33

35

34

Products & Service: www.ecs-electronicsuk.co.uk

!

L R

MENUOK

P 500 miles6666 miles

Driving Aids

6:00 AM 36 F

C H0

1

23 4 5

6

7

8

RPMx1000

1/210

20

40

6080

100

120

140

160

20

40

60

80100

120 140160

180

200

220

240

260km/h

LED

RL

L 54 STOPR

Reverse

WARNING

OFF

VHz

Hz

Hz

Hz

A

V

COM10A

400mA

mA

V

mV

HOLD MINMAX RANGE

DC

Manual Range 60+

V

Functional test

part no.

LIGHTMATE IILIGHTMATE III

Revision: 7 / 03.02.2021PE-084-07MU




16/16

7-pin 13-pin

36

39

38

37

Adapter socketOptional

Rear parking sensor cut off

Revision: 7 / 03.02.2021PE-084-07MU




Part No: **-***-***

Electric wiring kit for towbars / 13-pin / 12 Volt / ISO 11446

This electric kit has to be installed by a professional workshop or a suitable qualified person.The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance!Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! Also please check that there is a definite compatibility between this vehicle and the electric kit!Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update).All warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected.If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted.This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment!Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle’s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system.Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module.We always recommend whenever possible, the following troubleshooting process: An analysis of the vehicle’s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module form the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team!Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. All of the data and illustrations may not be an exact representation but the text contained in this instructions must be observed!

Product overview

[email protected]


Revision: X / XX.XX.XXXXXX-XXX-XXX




citroËn / peugeot / vauxhall electric wiring kit for

Documents