catalogo portafolio fixkim

In the public opinion research commissioned to Social Research Center (SRC) by Consumer Academy, it has been come to light that Fixkim Insulation and Building Mortars are the most trusted brand by the consumer.

As a result of this survey conducted in Turkey, Fixkim was deemed worthy of 2011 Consumer Quality Award.

2

TABLE OF CONTENTS

QR BARCOD APPLICATION 5

COMPANY PROFILE 6-7

BALKÖPÜĞÜ EXTERIOR THERMAL SHEATING SYSTEM 8-9

JOINT FILLING COLORS 10

PACKING PICTOGRAMS 11

APPLICATION PICTOGRAMS 11

THERMAL INSULATION MATERIALS 12-13SHEET ADHESIVE MORTAR 14SHEET ADHESIVE MORTAR FOR OLD AND PAINTED SURFACES 15ACRILIC ADHESIVE 16SHEET ADHESIVE MORTAR FOR PLASTERED SURFACE 17FIBRATED / NON-FIBRATED SHEET PLASTER MORTAR 18THERMOFIX PERLITIC THERMAL INSULATION PLASTER 19SILICONE/NON-SILICONE DECORATIVE EXTERIOR COATING 20

ADHESIVE MORTARS 22-23CERAMIC ADHESIVE MORTAR 24FLEX CERAMIC ADHESIVE MORTAR 25EXTENDED RUN TIME CERAMIC ADHESIVE MORTAR 26FLEX POOL AND WET GROUND CERAMIC ADHESIVE MORTAR 27ON-TILE CERAMIC ADHESIVE MORTAR 28FLEX GRANITE AND MARBLE ADHESIVE MORTAR 29EXTRA FLEX GRANITE AND MARBLE ADHESIVE MORTAR 30TWO COMPONENT GRANITE AND MARBLE ADHESIVE MORTAR 31DECRATIVE BRICK AND STONE ADHESIVE MORTAR 32TWO COMPONENT DECORATIVE AND NATURAL STONE ADHESIVE MORTAR 33WALL AND NATURAL STONE MASONRY MORTAR 34GAS CONCRETE ADHESIVE MORTAR 35RIDGE TILE ADHESIVE MORTAR 36GLASS BRICK ADHESIVE MORTAR 37JAMB ADHESIVE MORTAR 38

JOINT FILLING MORTARS 40-41JOINT FILLING MORTAR 42FLEX JOINT FILLING MORTAR 43FLEX POOL AND WET GROUND JOINT FILLING MORTAR 44FLEX EXTENSIVE JOINT FILLING MORTAR 45SILICONE JOINT FILLING MORTAR 46ANTIBACTERIAL SILICONE JOINT FILLING MORTAR 47EPOXY BASED JOINT FILLING MORTAR 48GLASS BRICK JOINT FILLING MORTAR 49

REPAIR AND STRENGTHENING MORTARS 50-51FIBRATED THICK REPAIR MORTAR 52FIBRATED/NON-FIBRATED THIN REPAIR MORTAR 53QUICK SETTING THICK REPAIR MORTAR 54QUICK SETTING THIN REPAIR MORTAR 55FIX-MORTAR 56ANCHORAGE AND FIXING MORTAR 57NON-SHRINK GROUT MORTAR 58FLUID GROUT MORTAR 59SC 215 ANCHORAGE MORTAR 60SC 315 ANCHORAGE MORTAR 61

3

PLASTERS AND PUTTIES 62-63MACHINE PLASTER 64HAND PLASTER 65FIXTEK PLASTER 66SATIN PUTTY 67POWDER PRIMER 68RESTORATION PLASTER 69

GROUND APPLICATION MORTARS 70-71SELF-SPRAWLING FINE LEVELLING SCREED (3-7 MM) 72SELF- SPRAWLING THICK LEVELLING SCREED (7-15 MM) 73QUICK SETTING AND SELF- SPRAWLING LEVELLING SCREED (3-7 MM) 74NORMAL SCREED 75LIGHT SCREED 76

GROUND SURFACE HARDENERS 78-79BASALT AGGREGATED SURFACE HARDENERS 80SILICA AGGREGATE SURFACED HARDENERS 81QUARTZ AGGREGATED SURFACE HARDENERS 82CORUNDUM AGGREGATED SURFACE HARDENERS 83

WATERPROOFING MORTARS 84-85CRYSTALIZED WATERPROOFING MORTAR 86SINGLE COMPONENT WATERPROOFING MORTAR 87FLEXIBLE TWO COMPONENT WATERPROOFING MATERIAL 88SUPER FLEXIBLE TWO COMPONENT WATERPROOFING MATERIAL (LIQUID MEMBRANE) 89FIXWATERSTOP 90TWO COMPONENT SELF- SPRAWLING WATER-REPELLENT LEVELLING SCREED 91

WATERPROOFING SYSTEMS 92-93PU 160 LIQUID MEMBRANE 94PU 250 WATERPROOF COATING 95LIQUID MEMBRANE 96BT 2K 97BT 1K 98

CURE LIQUIDS 100-101PARAFFIN BASED CURE LIQUID 102ACRYLIC RESIN BASED CURE LIQUID 103SOLVENT BASED CURE LIQUID 104

PRIMERS 106-107LIQUID PRIMER 108PRIMER 800 EXPOSED CONCRETE LINING 109GENERAL PURPOSE ACRYLIC PRIMER 110RAMMED LINING 111

FORM OILS 112-113STEEL FORM OIL 114PLYWOOD FORM OIL 115WOODEN FORM OIL 116

MORTAR ADDITIVES 118-119WATERPROOFING MORTAR ADDITIVE 120LATEX ADHERENCE AUGMENTER MORTAR ADDITIVE 121ANTIFREEZE MORTAR ADDITIVE 122SETTING RETARDER MORTAR ADDITIVE 123PLASTICIZER MORTAR ADDITIVE 124TICKENER MORTAR ADDITIVE 125

EPOXY COATINGS AND PAINTS 126-127SC 600 SELF-LEVELLING COATING 128SC 605 EPOXY PAINT 129CHLORINATED RUBBER MARKING PAINT 130

EPOXY PRIMERS 132-133SC 270 PRIMER 134SC 220 PRIMER 135SC 210 PRIMER 136NATURAL STONE PROTECTOR 137

EXTERIOR PAINTS 138-139SILICONE EXTERIOR PAINT 140ACRYLIC EXTERIOR PAINT 141THERMAL EXTERIOR PAINT 142SILICONE EXTERIOR COATING 143ACRYLIC EXTRIOR COATING 144

GYPSUM PRODUCTS 146-147MACHINE-APPLIED PLASTER 148SATIN PLASTER 149PERLITIC SGYPSUM 150PAPIER MACHE GYPSUM 151

MEMBRANES 152-153FİXKİM MEMBRANS 154F 2000 – F 3000 P 3000 – P 4000 ALM 3000 ARD 4000

POWERMIX MEMBRAN 155F 2000 - F 3000P 3000 - P 4000ALM 3000 - ALM 4000

4

5

FİXKİM Products are in your mobile phone now.

Fixkim, as being one of the leading companies in the sector, takes advantages of technological benefits and shares these opportunities with its customers. In order to simplify workings of the Craftsmen and professionals and to ensure the achievement of detailed information Fixkim has included the “QR Code Reader” application in its catalogues.

What is the QR Code Reader?QR Code Reader is a digital barcode system which needs only a mobile phone and ensuring to reach at the FİXKİM’s web page where there is a data bank including the detailed information about the use of the products at any point and any time by using the internet opportunities.

How to use QR Code Reader?In order to use the QR Code Reader System, firstly, you need a mobile phone with camera. After you have installed the barcode reader program on your mobile fine, you should run the application and close your mobile phone the QR Code, and then you should take the photograph of the QR code by means of your mobile phone’s camera. By virtue of this application, you will be redirected automatically to the data bank and you can easily reach the detailed information such as description of a requested FİXKİM product, how is it applied, what are the application areas and technical specifications of that product.

QR BARCODE APPLICATION

When you approach your mobile phone to below QR Code Reader, you will automatically redirected to the web page of FİXKİM and you can reach detailed information

FİXKİM is the most favorite company of Balcı Group of Companies and one of the leading companies in the industry since 2004. It has been strengthened its

success with the ISO 9001, TSE, CE, GOST-R quality management certificates.

FİXKİM A.Ş. has been organized in construction chemicals and it has put into service the EPS/Styrofoam factory at the end of the year 2007.

It offers powder and liquid chemical products which can be defined as “special” except the known products in construction chemicals. It has been reinforced

its quality with its wide range of product options offered to the industry and the certificates of ISO 9001, TSE, CE, GOST-R received for its nearly 200 product

range and its membership of associations of IZODER, PUD and IMSAT.

Our factory in Tuzla which has started production at full capacity at the beginning of 2008 has working with the capacity of daily 1500 m3 EPS and 600 tons of

Construction Mortars, Construction Chemicals and Waterproofing Systems. Our factory is established in the open area of 10.000 m2 and closed area of 16.000

m2, and equipped with the latest machinery technology. It has made its place in the EPS industry in a short time with its experienced staff.

Our EPS blocks with the brand name of FİXKİMPOR are manufactured between the densities of 10 to 32. Although the vast majority of the production is for

exterior sheathing it has also resources of human and machinery that can meet different needs.

For the residential buildings, it is true that to prevent energy loss is one of the most important investments would be taken against the energy needs growing

every year in the country. While applying the internal and external insulation in the buildings it is a fact that sheathing is the best insolation method. By means

of sheathing it is possible to achieve the saving between 50% - 60% in temperature.

Based on this fact we have developed totally new system on exterior sheathing.

“BALKÖPÜĞÜ Exterior Sheathing System”

The known exterior sheathing systems obtains the main materials to be used in practice from the contract manufacturers. This situation reduces the effici-

ency and lead to problems during the implementation phase.

The main products within the Balköpüğü Exterior Sheathing System, particularly FİXKİMPOR, are produced with the quality assurance of FİXKİM A.Ş. and by

virtue of the compliance of each product with each other a complete efficiency is achieved in the coating application.

We have strengthened our waterproofing systems with the production of FİXKİM and POWERMIX Membrane.

In order to look at the future confidently, in order to strengthen our ties with our business partners and to achieve new successes together, FİXKİM A.Ş. will

in an effort to add one more to the right jobs and applications in each new day.

7

COMPANY PROFILE

10

JOINT FILLING COLORS

BLACK WHITE

CHAMPAGNE IVORY-WHITETOBACCO-COLORED

LAVENDER SOMON COLOR BEIGE CREAM

BROWN DUSTY ROSE PINK LILAC

DULL GRAY GRAY AZURE BLUE ICE

STRAWYELLOW

PACKING PICTOGRAMS

11

APPLICATION PICTOGRAMS

KRAFT SACK TIN BUCKET PLASTIC BUCKET

YELLOW JERRY CAN BLUE JERRY CAN BARREL MEMBRANE

BRUSH ROLLER SPRAYING GUN TROWEL GLASS-FIBER MESH

SPIKED ROLLER NOTCHED TROWEL SPRINKLER SPONGE HARROW

SPATULA RUBBER MALLET DRILL MIXER AIRLESS

SHEET ADHESIVE MORTAR

SHEET ADHESIVE MORTAR FOR OLD AND PAINTED SURFACES

ACRILIC ADHESIVE

SHEET ADHESIVE MORTAR FOR PLASTERED SURFACE

FIBRATED / NON-FIBRATED SHEET PLASTER MORTAR

THERMOFIX PERLITIC THERMAL INSULATION PLASTER

SILICONE/NON-SILICONE DECORATIVE EXTERIOR COATING

THERMAL INSULATION MATERIALS

DESCRIPTIONIt is a polymer blended and cement-based ready-mixed mortar that is used in bon-ding the thermal insulation panels and provides high adhesion.

APPLICATION AREASExtrude Polystyrene (XPS) or Expanaded Polystyrene (EPS) used in exterior dres-sing are used in covering the stone wool and rock wool thermal insulation panels with a layer of plaster.

SURFACE PREPARATIONThe surface should be clean, dry, smooth and intact. Very porous surfaces should be wet and the surface should be kept to be saturated with moisture. Signifcant de-fects on the surface should be repaired with FİXKİM Repair Mortar at least 24 hours before bonding application of the thermal insulation panels. It should be noted that the application surface should be cured.

APPLICATION CONDITIONSIt should be considered that the ambient temperature is between +5 oC to +35 oC during the application. It should not be applied for the frozen, melting surfaces or the surfaces that is at the risk of frost within 24 hours. It should not be applied under direct sunlight and strong wind.

APPLICATION FEATURESPot life of the prepared mortar is up to 2 hours and application thickness of it should be 4 mm. Insulation panels should be placed with approximation together thoro-ughly, in order to avoid the heat transfer the gaps between the panels should be as small as possible.

IMPLEMENTATION25 kg FİXKİM Thermal Insulation Sheet Adhesive shall be poured into 6 – 6.5 liter clean water and mixed with a low-speed mixer until getting a lump-free homoge-nous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again for 1-2 minutes. Thermal Insulation Sheet Adhesive should be applied to the surface at 1 cm with a steel trowel. The adhesive mortar shall be applied to surround the insulation plate by taking care to keep 5 mm from the edges. It should be applied as three points at the central section of the plate. It sould be noted that at least 40% of the insulation plate is covered with adhesive mortar. The plate shall be suppres-sed on the surface to be bonded. After the adhesive is curred sufficiently the sheet shell be plugged. Depending on the wether conditions, application of the plaster can be implemented two day later.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In cannot be applied on the wood coatings, metal coatings and the surfaces exposed to moisture. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTION4-5 kg/m2 (Varies depending on the method of application)

STORAGEIt should be stored in a dry and moisture free environment with a maximum 10-fold stacking for a period of 8 months. It is recommended to be consumed within 7 days after opening the package.

HEALTH AND SAFETYAvoid contact with skin and eyes. Gloves must be worn during packaging and application.

TECHNICAL SPECIFICATIONS Appearance Gray-colored fine powder Powder Density 1,550 ± 150 kg/ m3

Water Mixing Ratio 6-6,5 lt. water / 25 kg. powder Water Vapour Transmission μ ≤ 15Water Absorbtion 30 min. ≤ 0,5 Kg / ( m2min. 0,5 ) Adherence Strength > 0,1 N/mm2

Slipping < 0,5 mm Compressive Strength > 10 N/mm2

Bending Strength > 4 N/mm2

Time for Plaster Implementation on it After 1 to 2 days Plugging Time After 24 hours Crustation Time < 25 min. 20 oC Shelf Life 8 months in dry conditions Packing 25 kg. foil kraft paper bag The density of fresh mortar mixture 1,70± 100 g/cm3

Particle size < 0.8 mm

14

THERMAL INSULATION SHEET ADHESIVE MORTAR

DESCRIPTIONIt is a polymer blended and cement-based ready-mixed mortar that is used in bon-ding the thermal insulation panels on the painted surfaces.

APPLICATION AREASExtrude Polystyrene (XPS) or Expanaded Polystyrene (EPS) used for exterior or in-terior insulation are used in bonding the stone wool and rock wool thermal insulation panels on the painted wall.




IMPLEMENTATION25 kg FİXKİM Thermal Insulation Sheet Adhesive for Painted Surfaces shall be pou-red into 6 – 6.5 liter clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again for 1-2 minutes. Thermal Insulation Sheet Adhesive should be appli-ed to the surface at 1 cm with a steel trowel. The adhesive mortar shall be applied to surround the insulation plate by taking care to keep 5 mm from the edges. It should be applied as three points at the central section of the plate. It sould be noted that at least 40% of the insulation plate is covered with adhesive mortar. The plate shall be suppressed on the surface to be bonded. After the adhesive is curred sufficiently the sheet shell be plugged. Depending on the wether conditions, application of the plaster can be implemented two day later.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In cannot be applied on the wood coatings, metal coatings and the surfaces exposed to moisture. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The pac-kaged products should not be stored in humid conditions.


STORAGEIt should be stored in a dry and moisture free environment with a maximum 10-fold stacking in its original package for a period of 8 months. It is recommended to be consumed within 7 days after opening the package.

HEALTH AND SAFETYAvoid contact with skin and eyes. Gloves must be worn during packaging and app-lication.

TECHNICAL SPECIFICATIONS Appearance Gray-colored fine powder Powder Density 1,550 ± 150 kg/ m3 Water Mixing Ratio 6-6,5 lt. water / 25 kg. powder Water Vapour Transmission μ ≤ 15 Water Absorbtion 30 min. ≤ 0,5 Kg / ( m2 min. 0,5 ) Adherence Strength > 0,12 N/mm2 Slipping < 0,5 mm Compressive Strength > 14 N/mm2 Bending Strength > 4,4 N/mm2 Time for Plaster Implementation on it After 1 to 2 days Plugging Time After minimum 24 hours Crustation Time < 25 min. 20 C˚ Shelf Life 8 months in dry conditions The density of fresh mortar mixture 1,70± 100 g/cm3 Particle size < 0.8 mm

SHEET ADHESIVE MORTAR FOR OLD AND PAINTED SURFACES

15

DESCRIPTIONIt is an elastic type acrylic dispersion based adhesive ready to use for bonding the thermal insulation sheets.

APPLICATION AREASIt is used for bonding the mineral based betopan, sypsum board in interiors and exteriors and bonding the thermal insulation plates on the plastered and painted surfaces.

SURFACE PREPARATION AND APPLICATIONThe materials that prevent the adherence such as form oil, dust, paint, dirt, etc. should be removed from the surface to be applied. Cracks and holes on the sur-face should be covered with the suitable FİXKİM repair mortar. At the high water permeability surfaces, the surface should be primed with a suitable primer before application. The acrylic adhesive should be applied on the thermal insulation plate to cover the complete surface of the sheet with a notched trowel. In order to obtain a better result the product should be applied on the surface and thermal insulation plate. Plugging process should be started after 2-3 days.

APPLICATION CONDITIONSIt should be considered that the ambient temperature is between +5 oC to +30 oC during the application.

APPLICATION FEATURESThe time to wait between the coatings: 24 hours.

CONSUMPTION3,50-4,00 kg /m2

STORAGEIt can be stored in the indoor conditions in its original packaging at +5 oC to +30 oC for a period of one year. They should be stored maximum three rows one on the top of the other.

SAFETY WARNINGSR10: FlammableR20-21-22: It is harmful in case of inhalation, swallowing and in conract with skin.S2: Keep out of the reach of children.S20-21: Do not eat or drink when you are working.S24-25: Keep away from contact with eyes and skin.S26: In case of contact wit eyes, rinse plenty of water and seek medical advice.S36-37-39 Wear suitable protecting clothing, gloves, goggles and face protection mask when you are working.S-36: It is irritative for eyes.S-38: It irritates the skin.S-42: It may cause sensitization by inhalation.

TECHNICAL SPECIFICATIONS Color White Density 1,70 kg/lt Application tempature Between +5 oC to 35 oC Running time 25 minutes at 25 oC Surface drying time 60-90 minutes at 25 oC Packaging 15 kg Application Trowel, Notched trowel Cleaning the instruments used in It shall be cleaned with water Diluent It shall be used without dilution

ACRILIC ADHESIVE

16

DESCRIPTIONIt is a polymer blended and cement-based ready-mixed mortar that is used in bon-ding the thermal insulation panels on the plastered surfaces.

APPLICATION AREASExtrude Polystyrene (XPS) or Expanaded Polystyrene (EPS) used for exterior or in-terior insulation are used in bonding the stone wool and rock wool thermal insulation panels without plugging on the plastered wall.




IMPLEMENTATION25 kg Fİxkim Thermal Insulation Sheet Adhesive for Plastered Surfaces shall be po-ured into 6 – 6.5 liter clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again for 1-2 minutes. Thermal Insulation Sheet Adhesive should be appli-ed to the surface at 1 cm with a steel trowel. The adhesive mortar shall be applied to surround the insulation plate by taking care to keep 5 mm from the edges. It should be applied as three points at the central section of the plate. It sould be noted that at least 40% of the insulation plate is covered with adhesive mortar. The plate shall be suppressed on the surface to be bonded. Depending on the wether conditions, application of the plaster can be implemented two day later.



STORAGEIt should be stored in a dry and moisture free environment with a maximum 10-fold stacking in its original package for a period of 8 months. It is recommended to be consumed within 7 days after opening the package.


TECHNICAL SPECIFICATIONS Appearance Gray-colored fine powder Powder Density 1,550 ± 150 kg/ m3

Water Mixing Ratio 6-6,5 lt. water / 25 kg. powder Water Vapour Transmission μ ≤ 15Water Absorbtion 30 min. ≤ 0,5 Kg / ( m2 min. 0,5 ) Adherence Strength > 0,11 N/mm2

Slipping < 0,5 mm Compressive Strength > 12 N/mm2

Bending Strength > 4,2 N/mm2

Time for Plaster Implementation on it After 1 to 2 days Crustation Time < 25 min. 20 ˚C Shelf Life 8 months in dry conditions The density of fresh mortar mixture 1,70± 100 g/cm3

Particle size < 0.8 mm

SHEET ADHESIVE MORTAR FOR PLASTERED SURFACE

17

DESCRIPTIONIt is a fiber-reinforced and cement based plaster mortar with fine aggregate, pro-viding high strength and prepared for creating a layer of plaster on the thermal in-sulation plates.

APPLICATION AREASExtrude Polystyrene (XPS) or Expanaded Polystyrene (EPS) used in exterior dres-sing are used in covering the stone wool and rock wool thermal insulation panels with a layer of plaster.

SURFACE PREPARATIONThe application surface and the plates should be firm and any anti-adhesion subs-tances such as dust, oil, paint, silicone, curing agents and detergents should be cle-aned. The plates to be plastered must be robust and fully inserted, and the gaps between them should be covered with the same material or foam. At least 48 hours should be passed after the process of bonding the plates on the wall.


APPLICATION FEATURESPot life of the prepared mortar is up to 2 hours and application thickness (under mesh) of it should be 3 mm. The time required to wait between coats: 3-4 hours. The time reqired to wait for the implementation of the final coat on the Styrofoam: 7 days.

IMPLEMENTATION25 kg FİXKİM Fibrated Thermal Insulation Sheet Plaster Mortar shall be poured into 6 – 6.5 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again for 1-2 minutes. The plaster mortar should be applied to the surface with a steel trowel. The first coat of mortar (3 mm) shall be applied on the pre-pastd plate with a steel trowel. The fiber mesh shall be placed and it shall be buried into the fresh mortar. The fiber mesh should be placed from the top down, pressed and thoroughly stretched, without being folded and to be equal distance at whole surface of the insulation sheet. In order to prevent cracking, the fiber mesh should be applied by overlapping 10 cm at the connection points. The fiber mesh should be returned at least 20 cm at the corners and all of the joists, windows and door frames. A second plaster application can be made after 3-4 hours. After you apply the plaster, the scond (2 mm) plaster shall be applied. Prior to the application, the surface must be dampened. After application the surface will become suitable for exterior coating. Sponge tirifil weakens the adherence of the surface and may cause deforming of the surface; therefore do not use sponge tirifil.


CONSUMPTION4-5 kg/m2

STORAGEIt should be stored in a dry and moisture free environment with a maximum 10-fold stacking for a period of 8 months in its original package. It is recommended to be consumed within 7 days after opening the package.


TECHNICAL SPECIFICATIONS Appearance Gray-colored fine powder Powder Density 1,55 ± 150 kg/ m3 Water Mixing Ratio 6-6,5 lt. water / 25 kg. powder Pot life Up to 2 hoursHollow bulk density of the hardened plaster 1,35 ±150 kg/ m3 Bending Strength > 5 N/mm2 Compressive Strength > 12 N/mm2 Water Vapour Transmission μ ≤ 15Water Absorbtion 30 min. ≤ 0,5 Kg / ( m2 min. 0,5 ) Shelf Life 8 months in dry conditions The density of wet mortar mixture 1650 ± 100 g/cm3 Adherence Strength > 0,1 N/mm2Brightness G3Dry Film Thickness E5Particle Size S3Crack Covering A0Carbon dioxide permeability C0Resistance to Mold Growth K2

FIBRATED / NON-FIBRATED SHEET PLASTER MORTAR

18

APPLICATION FEATURESThermofix Thermal Insulation Plaster provides thermal insulation by 30-40%. Since it is used as a plaster it does not create thermal bridges. It is an A1 class fire resis-tant and breathable, and does not impose burden to the buildings with its lightwe-ight structure, and does not contain carcinogenic substances. It ensures the sound insulation; is resistant to the acid rains and prevents the formaition of mold and fungus by preventing the humidity and moisture.

IMPLEMENTATIONThermofix Thermal Insulation Plaster is mixed with a mixer (13,5 – 14,5 lt. water for 20 Kg. bag) and applied to the surface with a trowel or by spraying to tha surface with a plaster machine. All of the water should not be added at once but gradually. To obtain a proper plaster special aluminium gauge profiles should be used. In order to prevent breakages at the corners corner profiles should be used. Thermofix Ther-mal Insulation Plaster that is applied between two plates in horizontal stripes shall be leveled with special aluminium gauge profiles. When the plaster hardens suffici-ently (when pressed with fingers it should not be curved), the surface shall become threadbare. The surface shall be finished with a damp sponge. Application thickness is between 1 cm and 5 cm at single layer. If the thickness is greater than 5 cm, the second layer shall be applied max. 2-2,5 cm after the setting of the first layer. The time required to wait between the coats in the applications is 24 hours.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mor-tar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In cannot be applied on the wood coatings, metal coatings and the surfaces exposed to moisture. In terms of the durability of the product, the surface should be watered regularly within 7 days after afflication. Plaster mesh is recommended at the junction of the different materials and at the points where a movement can occur. For the applications to be made on the heat insulation plaster you should wait at least 15 days depending on the ambient temperature. Do not vi-olate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immedi-ately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTION4-5 kg/m2

STORAGEIt should be stored in a dry and moisture free environment with a maximum 10-fold stacking for a period of 8 months in its original package. It is recommended to be consumed within 7 days after opening the package.


TECHNICAL SPECIFICATIONS Appearance White-colored fine powder Powder Density 500 ± 50 kg/ m3

Water Mixing Ratio 13,5-14,5 lt. water / 20 kg. powder Application temperature Between +5°C and 35°C Adherence Strength > 0,1 N/mm2

Sound Insulation Value 25 db (3cm/500Hz) Compressive Strength > 1,6 N /mm2

Bending Strength > 0,9 N /mm2

Water absorbtion 0,240 (kg./m2 min0,5) Thermal Conductivity 0,055 (W/mk) Skinning Time < 60 min. 20 °C Shelf Life 8 months in dry conditions Flammability Class A-1 Never Flammable Water Vapor Permeability (Μ) 3 (<15)

THERMOFIX PERLITIC THERMAL INSULATION PLASTER

19

DESCRIPTIONIt is cement-based ecological insulation plaster can be applied to the interior and ex-terior brick, aerated concrete, pumice, brick walls by hand or machine; providing to opportunity practical adhesion and implementation, formed by supporting with the natural raw materials and ensuring the heat+water+sound and fire insulation.

APPLICATION AREASIt is used as insulation plaster on brick, aerated concrete, pumice, briquette and ex-posed concrete surfaces and walls. It would not be applied for lime and gypseous surfaces.

SURFACE PREPARATIONThe materials that prevent the adherence such as form oil, dust, paint, dirt, etc. sho-uld be removed from the surface to be applied. Cracks and holes on the surface should be covered with the suitable FİXKİM repair mortar. The surface should be dampe-ned before application. Base coat implementation should be executed for the aerated concrete, exposed concrete surfaces 3 days ago. After the previous base coat is dried (at least 72 hours) the plaster should be applied. The base coat applied previously should be wetted for 3 days at regular intervals. On the exposed concrete surfaces with the surface smoothness and brightness base coat application should be execu-ted together with the exposed concrete primer and the application should be made after the base coat is dried.

APPLICATION CONDITIONSIt should be considered that the ambient temperature is between +5 oC to +35 oC du-ring the application. It should not be applied for the frozen, melting surfaces or the surfaces that is at the risk of frost within 24 hours. It should not be applied under direct sunlight and strong wind.

SILICONE/NON-SILICONE DECORATIVE EXTERIOR

COATING

20

DESCRIPTIONIt is the white cement based, one-component, containing polymer, trowel applied, and mineral textured mineral final coating material.

APPLICATION AREASIt is used as the final coating material at the exteriors of all buildings and on the exterior insulation systems.

SURFACE PREPARATIONThe surface should be clean, smooth and firm. Prior to the application the surface must be damped certainly and should be saturated with water in very hot and windy weather conditions. Adherence enhancer and anti-dusting FİXKİM primer should be applied on the surface with a brush.


APPLICATION FEATURESMixing time: 5 minutes, Conditioning time of the mortar: 1-2 minutes, Pot life: 1 hour, Layer thickness: 2 mm, completely drying time: 2-3 days.

IMPLEMENTATION25 kg Fixkim Decorative Plaster Mortar shall be poured into 6 – 6.5 liter clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 1-2 minutes and mixed again for 1-2 minutes. The decorative plaster should be applied to the surface at equal distence with a steel trowel and application thickness should be adjusted according to the largest pattern stone. Application thickness is 2 mm. The surface is designed with circular motion by a plastic trowel. The pattern-making process should always be done when the decora-tive plaster is moist. The specified periods of time are valid for at the surface and am-bient temperature of 20 oC, the period increases at low temperature and decreases at high temperatures. The surface should be dampened for 7 days after application.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In cannot be applied on the wood coatings, metal coatings and the surfaces exposed to moisture. Do not violate the conditions for the specified applica-tion surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTION3-3,5 kg/m2

STORAGEIt should be stored in a dry and moisture free environment with a maximum 10-fold stacking for a period of 8 months in its original package. It is recommended to be con-sumed within 7 days after opening the package.

HEALTH AND SAFETYAvoid contact with skin and eyes. Gloves must be worn during packaging and appli-cation.

TECHNICAL SPECIFICATIONS Appearance Beyaz Poeder Density 1,50 ± 100 kg/ m3

Water Mixing Ratio 6-6,5 lt. water / 25 kg. powder Water Vapor Transmission Rate V 2 (≤ 150 - > 15 g / (m2 d) About 50 – 60 g / (m2 d) Water Transfer Rate W 2 ( ≤ 0,5 - > 0,1 Kg / (m2 h0,5) About 0,02-0,04 Kg / (m2 h0,5) Full curing time 2-3 days Dry Film Thickness E 5 (> 400 μm) About 1200 – 1800 μm Wet Unit Weight 1700 ±100 kg./m3 Compressive Strength > 10 N/mm2


Shelf Life 6 months in dry conditions Adherence Strength > 0,1 N/ mm2

Particle Size S 4 (> 1500 μm) About 1600 – 2000 μm Crack Covering Feature A0 Carbon dioxide permeability C0 Resistance to Mold Growth K2

CERAMIC ADHESIVE MORTAR

FLEX CERAMIC ADHESIVE MORTAR

EXTENDED RUN TIME CERAMIC ADHESIVE MORTAR

FLEX POOL AND WET GROUND CERAMIC ADHESIVE MORTAR

ON-TILE CERAMIC ADHESIVE MORTAR

FLEX GRANITE AND MARBLE ADHESIVE MORTAR

EXTRA FLEX GRANITE AND MARBLE ADHESIVE MORTAR

TWO COMPONENT GRANITE AND MARBLE ADHESIVE MORTAR

DECRATIVE BRICK AND STONE ADHESIVE MORTAR

TWO COMPONENT DECORATIVE AND NATURAL STONE ADHESIVE MORTAR

WALL AND NATURAL STONE MASONRY MORTAR

GAS CONCRETE ADHESIVE MORTAR

RIDGE TILE ADHESIVE MORTAR

GLASS BRICK ADHESIVE MORTAR

JAMB ADHESIVE MORTAR

ADHESIVE MORTARS

CONSUMPTIONApplied Surface Notch Depth Consumption (Amount of Dust) Consumption (Amount of Mortar)1 m² 4x4x4 1,2-1,3 kg/m² 1,7-1,8 kg/m²1 m² 6x6x6 1,7-1,9 kg/m² 2,3-2,5 kg/m²1 m² 8x8x8 2,4-2,6 kg/m² 3,2-3,5 kg/m²

DESCRIPTIONIt is cement based and polymer blended ceramic adhesive mortar with high bonding strength.

APPLICATION AREASIt is used for bonding the coating materials such as ceramics, tiles, glass mosaics, etc. on the cement-based surfaces. It is applied on the walls and floors indoors, and used on the ground outdoors.

SURFACE PREPARATIONDust, oil, paint and other chemicals and loose parts must be removed from the app-lication surface. The surface defects must be corrected with Fixkim Repair Mortar 24 hours in advance. All mineral based absorbent surfaces should be wetted before application and must be kept moist. In cases where the surface absorbance is high, the application should be made after primering the Fixkim Liquid Primer or Primer 800 to the surface.


IMPLEMENTATION25 kg Fixkim Ceramic Adhesive Mortar shall be poured into 6 – 7 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mor-tar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be applied to the surface by pulling in one direction with a notched steel trowel. The notch size of the trowel should be determined according to the size of the ceramic to be tiled and smoothness of the surface to be treated. The ceramics shall be adhered to the mortar surface in within 20 minutes. In order to ensure full contact of the mortar to the tile you should apply a force to the ceramic with the aid of rubber hummer. It should be noticed that the desired range of joint gap should be allowed between the ceramics. Joint filling process should be started at least 48 hour after the adhesive application.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In cannot be applied on the wood coatings, metal coatings and the surfaces exposed to moisture. It should not be applied without using the adherence enhancing primer on the surfaces such as gypsum panel, gypsum plaster, gypsum block, etc. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.



TECHNICAL SPECIFICATIONS Appearance Gray-White colored fine powder Powder Density 1550 ± 100 kg./m3

Water Mixing Ratio 6-7 lt. water / 25 kg. powder Application Temperature Between +5°C and 35°C Pot Life Max. 2 hours Walking on After 24 hours Grouting After 48 hours Adhesion Strength > 0,5 N/mm2 (28 days) Slipping < 0.5 mm Open time 20 minutes. Shelf Life 8 months in dry conditions Class (TS EN 12004 ) C1 TE

CERAMIC ADHESIVE MORTAR

24

FLEX CERAMIC ADHESIVE MORTAR

25

DESCRIPTIONIt is cement based and polymer blended flex ceramic adhesive mortar with high bon-ding strength.

APPLICATION AREASIt provides superior performance in bonding the coating materials such as ceramic, porcelain tile and similar in interiors and exteriors. It can be used in cement-based plasters, concrete surfaces, floor heating coverings and the grounds exposed to high traffic.



APPLICATION FEATURESIt is suitable for use in the places which has high temperature difference.

IMPLEMENTATION25 kg Fixkim Flex Ceramic Adhesive Mortar shall be poured into 6 – 7 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be app-lied to the surface by pulling in one direction with a notched steel trowel. The notch size of the trowel should be determined according to the size of the ceramic to be tiled and smoothness of the surface to be treated. The ceramics shall be adhered to the mortar surface in within 20 minutes. In order to ensure full contact of the mortar to the tile you should apply a force to the ceramic with the aid of rubber hummer. It should be noticed that the desired range of joint gap should be allowed between the ceramics. Joint filling process should be started at least 48 hour after the adhesive application.





Water Mixing Ratio 6-7 lt. water / 25 kg. powder Application Temperature Between +5°C and 35°C Pot Life Max. 2 hours Walking on After 24 hours Grouting After 48 hours Adhesion Strength > 1 N/mm2 (28 days) Slipping < 0.4 mm Open time 20 minutes. Shelf Life 8 months in dry conditions Class (TS EN 12004 ) C2 TE


EXTENDED RUN TIMECERAMIC ADHESIVE MORTAR

26

DESCRIPTIONIt is cement based and polymer blended and extended run time ceramic adhesive mortar with high bonding strength.

APPLICATION AREASIt is used for bonding the coating materials such as ceramics, tiles, glass mosaics, etc. on the cement-based surfaces. It is applied on the walls and floors indoors, and used on the ground outdoors.



IMPLEMENTATION25 kg Fixkim Extended Run Time Ceramic Adhesive Mortar shall be poured into 6 – 7 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be applied to the surface by pulling in one direction with a notched steel trowel. The notch size of the trowel should be determined according to the size of the ceramic to be tiled and smoothness of the surface to be treated. The ceramics shall be adhered to the mortar surface in within 30 minutes. In order to ensure full contact of the mortar to the tile you should apply a force to the ceramic with the aid of rubber hummer. It should be noticed that the desired range of joint gap should be allowed between the ceramics. Joint filling process should be started at least 48 hour after the adhesive application.




TECHNICAL SPECIFICATIONS Appearance Gray colored fine powder Powder Density 1500 ± 100 kg./m3

Water Mixing Ratio 6-7 lt. water / 25 kg. powder Application Temperature Between +5°C and 35°C Pot Life Max. 2,5 hours Walking on After 24 hours Grouting After 48 hours Adhesion Strength > 0,5 N/mm2 (28 days) Slipping < 0.5 mm Open time 30 minutes. Shelf Life 8 months in dry conditions Class (TS EN 12004 ) C1 TE


FLEX POOL AND WET GROUND CERAMIC ADHESIVE MORTAR

27

DESCRIPTIONIt is cement based and polymer blended flex pool and wet ground ceramic adhesive mortar with high bonding strength.

APPLICATION AREASIt provides superior performance in bonding the coating materials such as ceramic, porcelain tile and similar in interiors and exteriors (on wet surfaces such as terrace, bathroom, toilet, swimming pool, etc). It can be applied in cement-based plasters, concrete surfaces, floor heating coverings and the grounds exposed to high traffic.



APPLICATION FEATURESSuitable for use in the places which has high temperature difference.

IMPLEMENTATION25 kg Fixkim Flex Pool and Wet Ground Ceramic Adhesive Mortar shall be poured into 6 – 7 liter of clean water and mixed with a low-speed mixer until getting a lump-free ho-mogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be applied to the surface by pulling in one direction with a notched steel trowel. The notch size of the trowel should be determined according to the size of the ceramic to be tiled and smoothness of the surface to be treated. The ceramics shall be adhered to the mortar surface in within 20 minutes. In order to ensure full contact of the mortar to the tile you should apply a force to the ceramic with the aid of rub-ber hummer. It should be noticed that the desired range of joint gap should be allowed between the ceramics. Joint filling process should be started at least 48 hour after the adhesive application.





Water Mixing Ratio 6-7 lt. water / 25 kg. powder Application Temperature Between +5°C and 35°C Pot Life Max. 2 hours Walking on / Grouting After 24 hours / After 48 hours Water Absorption 30 min.≤ 0.1 kg / (m2 min 0.1) Adhesion Strength > 0,1 N/mm2 (28 days) Slipping < 0.3 mm Open time 20 minutes Shelf Life 8 months in dry conditions Class (TS EN 12004 ) C2 TE


28

DESCRIPTIONIt is cement based and polymer blended flex on-tile ceramic adhesive mortar with high bonding strength.


SURFACE PREPARATIONDust, oil, paint and other chemicals and loose parts must be removed from the app-lication surface. The surface defects must be corrected with Fixkim Repair Mortar 24 hours in advance. Zones should be established to connect by hammering over tile. The application should be made after primering the Fixkim Liquid Primer or Primer 800 to the surface.


APPLICATION FEATURESSuitable for use in the places which has high temperature difference. It is an exact solution in bonding the ceramics on tile.

IMPLEMENTATION25 kg Fixkim Flex Ceramic Adhesive Mortar shall be poured into 6 – 7 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be applied to the surface by pulling in one direction with a notched steel trowel. The notch size of the trowel should be determined according to the size of the ceramic to be tiled and smoothness of the surface to be treated. The ceramics shall be adhered to the mortar surface in within 20 minutes. In order to ensure full contact of the mortar to the tile you should apply a force to the ceramic with the aid of rubber hummer. It should be noticed that the desired range of joint gap should be allowed between the ceramics. Joint filling process should be started at least 48 hour after the adhesive application.



HEALTH AND SAFETYAvoid contact with skin and eyes. Gloves must be worn during packaging and applica-tion.

Appearance Gray-White colored fine powder Powder Density 1450 ± 100 kg./m3

Water Mixing Ratio 6-7 lt. water / 25 kg. powder Application Temperature Between +5°C and 35°C Pot Life Max. 2 hours Walking on After 24 hours Grouting After 48 hours Adhesion Strength > 1,1 N/mm2 (28 days) Slipping < 0.4 mm Open time 20 minutes Shelf Life 8 months in dry conditions Class (TS EN 12004 ) C2 T


ON-TILE CERAMIC ADHESIVE MORTAR


29

DESCRIPTIONIt is cement based and polymer blended flex granite and marble adhesive mortar with high bonding strength.

APPLICATION AREASIt is used in upholstering coating the large size floor and wall tiles, granite, granite ceramic, marble and all kinds of natural stone in interiors and exteriors. It used in the work places, shopping centers, schools and hospitals which are exposed to heavy pedestrian traffic.



APPLICATION FEATURESIt is ideal for the coating materials such as 40x40 sized ceramic, floor tile, glazed tile and granite. For greater sizes double-sided is recommended.

IMPLEMENTATION25 kg Fixkim Granite Adhesive Mortar shall be poured into 6 – 7 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be applied to the surface by pulling in one direction with a notched steel trowel. The notch size of the trowel should be determined according to the size of the granite to be tiled and smoothness of the surface to be treated. The granite shall be adhered to the mor-tar surface in within 20 minutes. In order to ensure full contact of the mortar to the granite you should apply a force to the granite with the aid of rubber hummer. It should be noticed that the desired range of joint gap should be allowed between the granites. Joint filling process should be started at least 48 hour after the adhesive application.





Water Mixing Ratio 6-7 lt. water / 25 kg. powder Application Temperature Between +5°C and 35°C Pot Life Max. 2 hours Walking on After 24 hours Grouting After 48 hours Adhesion Strength > 1 N/mm2 (28 days) Slipping < 0.5 mm Open time 20 minutes. Shelf Life 8 months in dry conditions Class (TS EN 12004 ) C1 TE S1

FLEX GRANITE AND MARBLE ADHESIVE MORTAR


30

DESCRIPTIONIt is cement based and polymer blended granite and marble adhesive mortar with high bonding strength.




APPLICATION FEATURESIt is ideal for the coating materials such as 40x40 sized ceramic, floor tile, glazed tile and granite. For greater sizes double-sided is recommended. Suitable for use in the places which has high temperature difference.

IMPLEMENTATION25 kg Fixkim Flex Granite Adhesive Mortar shall be poured into 6 – 7 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be app-lied to the surface by pulling in one direction with a notched steel trowel. The notch size of the trowel should be determined according to the size of the granite to be tiled and smoothness of the surface to be treated. The heavy granites should be bonded double sided. The granite shall be adhered to the mortar surface in within 20 minutes. In order to ensure full contact of the mortar to the granite you should apply a force to the granite with the aid of rubber hummer. It should be noticed that the desired range of joint gap should be allowed between the granites. Joint filling process should be started at least 48 hour after the adhesive application.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It sho-uld not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In cannot be applied on the wood coatings, metal coatings and the surfaces exposed to moisture. It should not be applied without using the adherence enhancing primer on the surfaces such as gypsum panel, gypsum plaster, gypsum block, etc. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

STORAGEIt should be stored in a dry and moisture free environment with a maximum 10-fold stac-king for a period of 8 months. It is recommended to be consumed within 7 days after opening the package.



Water Mixing Ratio 6-7 lt. water / 25 kg. powder Application Temperature Between +5°C and 35°C Pot Life Max. 2 hours Walking on After 24 hours Grouting After 48 hours Adhesion Strength > 1,1 N/mm2 (28 days) Slipping < 0,5 mm Open time 20 minutes. Shelf Life 8 months in dry conditions Class (TS EN 12004 ) C2 TE S2

EXTRA FLEX GRANITE AND MARBLE ADHESIVE MORTAR


31

DESCRIPTIONIt is two-component, very powerful and flexible granite and marble adhesive mortar which is formed with A component of cement based, polymer blended powder mor-tar and B component of acrylic emulsion.

APPLICATION AREASIt is used in upholstering the large size floor and wall tiles, granite, granite cera-mic, marble and all kinds of natural stone in interiors and exteriors in horizontal and vertical surfaces, in the work places, shopping centers, schools and hospitals which are exposed to heavy pedestrian traffic, in floor heating systems and coating the ceramic over the old granite and marble surfaces.



IMPLEMENTATIONThe component A (powder) shall be added slowly to the vessel in which there is the component B and mixed with a low-speed mixer until getting a lump-free homo-genous mixture. Extra water shall not be added to the mortar. The mortar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be applied to the surface by pulling in one direction with a notched steel trowel. The mixture in the vessel should be consumed within 1 hour. The notch size of the trowel should be determined according to the size of the ceramic to be tiled and smoothness of the surface to be treated. The granite shall be adhered to the mortar surface in within 20 minutes. In order to ensure full contact of the mortar to the granite you should apply a force to the granite with the aid of rubber hummer. It should be noticed that the desired range of joint gap should be allowed between the granites. Joint filling process should be started at least 48 hour after the adhesive application. In the sides without windows expansion joints should be left in each 5 meters. It should be noticed that the present dilatation joints should not be covered when the ceramics are being coated.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mor-tar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In cannot be applied on the wood coatings, metal coatings and the surfaces exposed to moisture. It should not be applied witho-ut using the adherence enhancing primer on the surfaces such as gypsum panel, gypsum plaster, gypsum block, etc. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The pac-kaged products should not be stored in humid conditions.



TECHNICAL SPECIFICATIONS Appearance Component A: Gray-White colored powder / Component B: White colored liquid Powder Density – Liquid Density 1450 ± 100 kg./m3 - 1 kg/lt Mixing Ratio 25 kg. powder / 6,5 kg liquid Application Temperature Between +5°C and 35°C Pot Life Max. 1 hours Walking on After 24 hours Pressure Strength > 14 N/mm2 (28 days) Adhesion Strength > 0.8 N/mm2 (28 days) Slipping < 0.5 mm Open time 30 minutes. Shelf Life 8 months in dry conditions Bending Strength > 5 N/mm2 (28 days)

TWO COMPONENT GRANITE AND MARBLE ADHESIVE MORTAR

DECORATIVE BRICK AND STONE ADHESIVE MORTAR

32

DESCRIPTIONIt is cement based and polymer blended decorative brick and stone adhesive mortar with high bonding strength.

APPLICATION AREASIt can be used for the aim of the coating the horizontal and vertical surfaces of the coating materials like decorative brick and natural stone.



IMPLEMENTATION25 kg Fixkim Decorative Brick and Stone Adhesive Mortar shall be poured into 6 – 6.5 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be applied to the surface of the decorative brick and stone with the help of trowel and bonded to the wall. In order to ensure full contact of the decorative brick and stone you should apply a force with the aid of rubber hummer. It should be noticed that the desired range of joint gap should be allowed between the decorative brick and stone. Joint filling process should be started at least 48 hour after the adhesive application.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In should not be applied on the wood coatings, metal coatings and the surfaces exposed to moisture. It cannot be applied without using the adherence enhancing primer on the surfaces such as gypsum panel, gypsum plaster, gypsum block, etc. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTIONAverage 8 kg/m3 for 5 mm thickness.




Water Mixing Ratio 6-6.5 lt. water / 25 kg. powder Application Temperature Between +5°C and 35°C Pot Life Max. 2 hours Walking on After 24 hours Grouting After 48 hours Adhesion Strength > 0.4 N/mm2 (28 days) Slipping < 0,5 mm Open time 20 minutes. Shelf Life 8 months in dry conditions Class (TS EN 12004 ) C1 T

33

TWO COMPONENT DECORATIVE AND NATURAL STONE ADHESIVE MORTAR

DESCRIPTIONIt is two-component, very powerful and flexible decorative brick and stone adhesive mortar which is formed with A component of cement based, polymer blended pow-der mortar and B component of acrylic emulsion.

APPLICATION AREASIt can be used for the aim of the coating the horizontal and vertical surfaces of the coating materials like decorative brick and natural stone.



IMPLEMENTATIONThe component A (powder) shall be added slowly to the vessel in which there is the component B and mixed with a low-speed mixer until getting a lump-free homo-genous mixture. Extra water shall not be added to the mortar. The mixture in the vessel should be consumed within 1 hour. The mortar shall be allowed to stand for 5 minutes and mixed again. The mortar shall be applied to the surface of the decorati-ve brick and stone with the help of trowel and bonded to the wall. In order to ensure full contact of the decorative brick and stone you should apply a force with the aid of rubber hummer. It should be noticed that the desired range of joint gap should be allowed between the decorative brick and stone. Joint filling process should be started at least 48 hour after the adhesive application.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In should not be applied on the wood coatings, metal coatings and the surfaces exposed to moisture. It cannot be applied without using the adherence enhancing primer on the surfaces such as gypsum panel, gypsum plaster, gypsum block, etc. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTIONAverage 7.5 kg/m3 for 5 mm thickness.



TECHNICAL SPECIFICATIONS Appearance Component A: Gray-White colored powder / Component B: White colored liquid Powder Density 1500 ± 100 kg./m3- 1kg/lt Mixing Ratio 25 kg. powder / 6.5 kg liquid Application Temperature Between +5°C and 35°C Pot Life Max. 1 hours Walking on After 24 hours Grouting After 48 hours Adhesion Strength > 0.6 N/mm2 (28 days) Slipping < 0,5 mm Open time 20 minutes. Shelf Life 8 months in dry conditions Pressure strength > 13 N/mm2(28 days) Bending strength > 4 N/mm2 (28 days)

34

WALL AND NATURAL STONE MASONRY MORTAR

DESCRIPTIONIt is the cement-based, high adhesive wall and natural stone masonry mortar that gives long working hours and having the reduced slipping feature.

APPLICATION AREASIt is be used in laying up the materials such as brick, briquette, pumice, and stone.

SURFACE PREPARATIONThe materials such as form oil, dust, oil, paint, dirt and so on which prevent the adhe-rence should be removed from the materials that the application will be performed. If the porous stone brick with the high level of absorbency or concrete plate is used or in order to prevent the water loss may occur in fresh mortar in high tempera-tures, the materials such as brick, briquette, pumice and natural stone should be wetted previously.


IMPLEMENTATION40 kg Fixkim wall masonry mortar shall be mixed in 8-9 liter water with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The bottom and side surfaces the first raw bricks, briquette, pumice, natural stone that contact with the mortar shall be wet and laid up. The prepared mortar can be used in horizontal and vertical application. It shall be applied on the masonry material with the trowel. The masonry materials shall be placed by tamping the sides and up.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood coatings, metal coating and the surfa-ces exposed to the moisture. Do not violate the conditions for the specified applica-tion surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.



TECHNICAL SPECIFICATIONS Appearance Gray-colored powder Powder Density 1,600 ± 200 kg/lt. Water Mixing Ratio 8–9 lt. water / 40 kg. water Pot Life Max. 2 hours Compressive Strength > 0,3 N/mm2 (28 days) Pressure Strength > 6 N/mm2 (28 days) Bending Strength > 2 N/mm2 (28 days) Drying time 24 hours

CONSUMPTION Width Length Height Consumption/Kg. Brick 8,5 19 19 13,5 Brick 13,5 19 19 21 Isobrick 14,5 23,5 24 18 Isobrick 19 23,5 24 24 Concrete briquette 19 19,5 39 22 Pumice briquette 15 18,5 39 18,5 Pumice briquette 19 18,5 39 23,5

35

GAS CONCRETE ADHESIVE MORTAR

DESCRIPTIONIt is the cement-based, high adhesive gas concrete masonry mortar that gives long working hours and having the reduced slipping feature.

APPLICATION AREASIt is used in laying up the wall with construction items such as foam concrete and brick that have a high rate if absorption. It is suitable for the leveling of the wall surfaces that was laid up and filling up the gaps and cracks.

SURFACE PREPARATIONThe application surface should be free from the anti-adhesion substances such as dust, oil, paint, silicone, curing agents and detergents.


IMPLEMENTATION20 kg Fixkim Gas Concrete Adhesive Mortar shall be poured into 7-8 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The bottom and side surfaces the first raw gas concrete that contact with the cons-truction mortar shall be wet and laid up. There is no need to be wet the gas concrete block for lying up. The gas concrete adhesive is applied to the surface with the trowel or 10x10 wide notched trowel. The horizontal and vertical joints should be maximum 3 mm. The laid up blocks should be placed by tamping the sides and top.




TECHNICAL SPECIFICATIONS Appearance Gray-colored fine powder Powder Density 1,300 ± 100 kg/lt. Water Mixing Ratio 7–8 lt. water / 20 kg. powder Pot Life Max. 2 hours Chloride Content Max. % 0,1 Bending Strength > 4 N/mm2 (28 days) Adhesive Strength > 0,4 N/mm2 (28 days) Pressure Strength > 8 N/mm2 (28 days) Air Content % 7 ± 3 Water absorption 30 min. ≤ 0,5 Kg / ( m2 min. 0,5 )

CONSUMPTION Brick Size Consumption / Kg. 20x50x20 cm 5-6 kg/m2

20x70x20 cm 6-7 kg/m2

30x50x15 cm 3-4 kg/m2

30x50x20 cm 4-5 kg/m2

30x70x20 cm 5-6 kg/m2

36

RIDGE TILE ADHESIVE MORTAR

DESCRIPTIONIt is the cement-based, single-component, polymer-added, fiber reinforced adhe-sive mortar with high performance and stability and used in the installation of the roof ridge tile

APPLICATION AREASIt is be used in bonding the ridge and tile etc. surfaces at roofs.

SURFACE PREPARATIONThe application surface should be free from the anti-adhesion substances such as dust, oil, paint, silicone, curing agents and detergents. The application surface should be wet and should be maintained to be wet.


IMPLEMENTATION25 kg Ridge Tile Adhesive Mortar shall be mixed in 5-6 liter of clean water with pre-ferably a low-speed mixer or trowel until getting a lump-free homogenous mixture. The prepared mortar shall be allowed to stand for 5 minutes for maturation and used by mixing again. The mixture in the vessel should be consumed within 2 hours. Previously, the adhesive mortar is applied to the application surface. Then it shall be applied to the joints of ridge tile without any gap. The last formation is shaped with a wet sponge. At the very hot temperature conditions, after the implementation please dampen the surfaces exposed to the sun for 24 hours.


CONSUMPTIONAverage of 600 gr for 1 pcs of tile.



TECHNICAL SPECIFICATIONS Appearance Tile-red fine powder Powder Density 1,400 ± 150 kg/lt. Water Mixing Ratio 5-6 lt. water / 25 kg. powder Pot Life Max. 2 hours Wet unit weight 1650 ± 100 Kg./m3

Bending Strength > 2 N/mm2 (28 days) Adhesion Strength > 0,2 N/mm2 (28 days) Pressure Strength > 8 N/mm2 (28) Walking on time 24 Hours

37

GLASS BRICK ADHESIVE MORTAR

DESCRIPTIONIt is the cement-based, high adhesive glass brick masonry mortar that gives long working hours and gains endurance rapidly.

APPLICATION AREASIt is be used in bonding the glass brick materials.

SURFACE PREPARATIONThe materials such as form oil, dust, oil, paint, dirt and so on which prevent the adhe-rence should be removed from the materials that the application will be performed. If there is a material with the high level of absorbency on the ground the mortar shall be applied or in order to prevent the water loss may occur in high temperatures in fresh mortar, the application surface should be wetted previously.


IMPLEMENTATIONFixkim Glass Brick Masonry Mortar shall be mixed in 4.5-5 liter of water with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The first raw glass bricks that contact with the mortar shall be wet and bonded. The prepared mortar can be used in horizontal and vertical application. It shall be applied on the masonry material with the trowel. The masonry materials shall be placed by tamping the sides and up.


CONSUMPTIONAverage of 15-16 kg/m2 for the thickness of 1cm



TECHNICAL SPECIFICATIONS Appearance White colored powder Powder Density 1,600 ± 100 kg/lt. Water Mixing Ratio 4,5 - 5 lt. water / 25 kg. Pot Life Max. 2 hours Bending Strength > 0,1 N/mm2 (28 days) Pressure Strength > 10 N/mm2 (28 days) Bending Strength > 3 N/mm2 (28 days) Drying Time 24 hours Particle Size S 4 ( > 1500 μm ) About 1600 – 2000 μm

38

JAMB ADHESIVE MORTAR

DESCRIPTIONIt is the cement-based, resin and polymer added, ready mortar that is used in bon-ding the EPS and XPS constructed jams and processed polyurethane products such as ceiling rose.

APPLICATION AREASIt is used in bonding the materials such as jamb, drywall, storey jambs and ceiling rose to the surface.

SURFACE PREPARATIONThe surface must be clean, dry, smooth and intact. Very porous surfaces should be wet and must be waited to be saturated. The significant defects must be repaired with Fixkim Repair Mortar at least 24 hours before the application. It should be noti-ced that the application surfaces should be cured.


APPLICATION FEATURESPot life: Up to 2 hours. Application thickness: 4 mm.

IMPLEMENTATION25 kg Fixkim Jamb Adhesive shall be poured into 6 – 6.5 liter of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again. The jamb adhesive should be applied to the jamb with the help of steel trowel. The adhesive mortar shall be appli-ed to the jamb so as to surround and in 5 cm from the edges. The jamb is suppressed to the surface. The adhesion is ensured by hitting at the jamb softly.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood surfaces, metal surfaces and the surfaces exposed to the moisture. It cannot be applied without using the adherence enhancing primer on the surfaces such as gypsum panel, gypsum plaster, gypsum block, etc. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTION4-5 kg / m2 (May change according to the application method)



TECHNICAL SPECIFICATIONS Appearance White-colored fine powder Powder Density 1,450 ± 150 kg/ m3

Water Mixing Ratio 6-6,5 lt. water / 25 kg.powder Water Vapor Transmission μ ≤ 15 Water absorption 30 min. ≤ 0,5 Kg / ( m2 dak 0,5 ) Adherence Strength > 0,2 N/mm2

Slipping < 0,5 mm Pressure Strength > 12 N/mm2


Particle Size < 0.8 mm Skinning Time < 20 dk. 20 °C Shelf Life 8 months in dry conditions Class C2 T S1

JOINT FILLING MORTARS

JOINT FILLING MORTARS

JOINT FILLING MORTAR

FLEX JOINT FILLING MORTAR

FLEX POOL AND WET GROUND JOINT FILLING MORTAR

FLEX EXTENSIVE JOINT FILLING MORTAR

SILICONE JOINT FILLING MORTAR

ANTIBACTERIAL SILICONE JOINT FILLING MORTAR

EPOXY BASED JOINT FILLING MORTAR

GLASS BRICK JOINT FILLING MORTAR

JOINT FILLING MORTAR

42

DESCRIPTIONIt is the cement-based, high-performance, single-component and easy proces-sed joint filling mortar that forms a smooth surface and used in 3-6 mm joints.

APPLICATION AREASIt is used for filling the joint gaps up to 6 mm of granite, ceramic, tile, marble, sto-ne and similar coating materials indoors, horizontal and vertical surfaces.

SURFACE PREPARATIONTo ensure a uniform color and desiccation, dust, sawdust, construction cement debris and so on that may be available in the joint gaps should be scraped by using a thin rod and be cleaned with a brush before the joint application process. The joint gaps especially on the walls should be dampened moisturized before the application. In order to prevent the tiles to get loose, it should be noticed that they are firmly adhered; accordingly the adherence is dried completely.

APPLICATION CONDITIONSIt should be considered that the ambient temperature is between +5 oC to +35 oC during the application. It should not be applied for the frozen, melting surfaces or the surfaces that is at the risk of frost within 24 hours. It should not be applied under direct sunlight and strong wind. Joint application process must be comple-ted 48 hours prior to laying tiles.

IMPLEMENTATION7.2 to 8 liters of water per 20 kg of Fixkim Joint Filling Mortar shall be mixed thoroughly with preferably a low-speed mixer or trowel until getting a lump-free homogenous mix-ture. After the joint filling mortar is allowed to stand for 5 minutes, it should be mixed again for 1 to 2 minutes before the application. The mortar shall be filled in the joint gaps with the hard rubber squeegee or the hard rubber base grouting spreading trowel. In or-der to fill the gaps well, the mortar should be trowelled previously parallel and then cross to the joints. The excess amount of the mortar on the surface shell be peeled off with a soft tipped spatula or moistened sponge-tipped spatula. After waiting for 15 to 30 minu-tes depending on ambient temperature the thin layer of grout that may remain on the surface must be cleaned thoroughly by wiping with a damp sponge. Surface smoothing and cleaning process should be done with a dry cloth when the grouting mortar is wet.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It sho-uld not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood coatings, metal coating and the surfaces exposed to the moisture. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves sho-uld be worn during the application. The packaged products should not be stored in humid conditions.

STORAGEIt should be stored in a dry and moisture free environment with a maximum 10-fold stac-king for a period of 8 months. It is recommended to be consumed within 7 days after ope-ning the package.


TECHNICAL SPECIFICATIONS Appearance White or colored fine powder Powder Density 1200 ± 100 gr/lt. Water Mixing Ratio 7,2 - 8 lt. water / 20 kg. powder Pot Life Approximately 1,5 hours Water absorption after 30 min. - Water absorption after 240 min. ≤ 5 - ≤ 10 Curing Time 12 hours Commissioning Time 24 hour for wall, 48 hours on the ground Bending Strength > 2,5 N/mm2 (EN 12808-3) Pressure Strength > 15 N/mm2 (EN 12808-3) Abrasion Resistance < 200 mm3 (EN 12808-2) Shrinkage < 3 mm/m. (EN 12808-4) Bending Strength After Freezing unsolved Min. 2 N/mm2 (EN 12808-3)Related standard CG1 ( TS EN 13888 )

Consumption Consumption according to the joint width (gr/m2)Tile sizes ( cm x cm) 3 mm 4 mm 5 mm 6 mm10 x 10 700 950 1200 150020 x 20 350 500 580 70030 x 30 250 300 420 500

COLOR


DESCRIPTIONIt is the cement-based, high-performance, single-component, easy processed and flexible joint filling mortar that forms a smooth surface and used in 3-6 mm joints.

APPLICATION AREASIt is used for filling the joint gaps up to 6 mm of granite, ceramic, tile, marble, stone and similar coating materials indoors, horizontal and vertical surfaces.

SURFACE PREPARATIONTo ensure a uniform color and desiccation, dust, sawdust, construction cement debris and so on that may be available in the joint gaps should be scraped by using a thin rod and be cleaned with a brush before the joint application process. The joint gaps especially on the walls should be dampened moisturized before the applica-tion. In order to prevent the tiles to get loose, it should be noticed that they are firmly adhered; accordingly the adherence is dried completely.

APPLICATION CONDITIONSIt should be considered that the ambient temperature is between +5 oC to +35 oC during the application. It should not be applied for the frozen, melting surfaces or the surfaces that is at the risk of frost within 24 hours. It should not be applied under direct sunlight and strong wind. Joint application process must be completed 48 hours prior to laying tiles.

IMPLEMENTATION7.2 to 8 liters of water per 20 kg of Fixkim Flex Joint Filling Mortar shall be mixed thoro-ughly with preferably a low-speed mixer or trowel until getting a lump-free homogenous mixture. After the joint filling mortar is allowed to stand for 5 minutes, it should be mixed again for 1 to 2 minutes before the application. The mortar shall be filled in the joint gaps with the hard rubber squeegee or the hard rubber base grouting spreading trowel. In or-der to fill the gaps well, the mortar should be trowelled previously parallel and then cross to the joints. The excess amount of the mortar on the surface shell be peeled off with a soft tipped spatula or moistened sponge-tipped spatula. After waiting for 15 to 30 mi-nutes depending on ambient temperature the thin layer of grout that may remain on the surface must be cleaned thoroughly by wiping with a damp sponge. Surface smoothing and cleaning process should be done with a dry cloth when the grouting mortar is wet.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It sho-uld not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood coatings, metal coating and the surfaces exposed to the moisture. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.



TECHNICAL SPECIFICATIONS Appearance White or colored fine powder Powder Density 1200 ± 100 gr/lt. Water Mixing Ratio 7,2 - 8 lt. water / 20 kg. powder Pot Life Approximately 1,5 hours Water absorption after 30 min. - Water absorption after 240 min. ≤ 5 - ≤ 10 Curing Time 12 hours Commissioning Time 24 hour for wall, 48 hours on the ground Bending Strength > 3 N/mm2 (EN 12808-3) Pressure Strength > 17 N/mm2 (EN 12808-3) Abrasion Resistance < 1000 mm3 (EN 12808-2) Shrinkage < 3 mm/m. (EN 12808-4) Bending Strength After Freezing unsolved Min. 3 N/mm2 (EN 12808-3) Related standard CG2A ( TS EN 13888 )

FLEX JOINT FILLING MORTAR

COLOR

43

FLEX POOL AND WET GROUND JOINT FILLING MORTAR

DESCRIPTIONIt is the cement-based, high-performance, single-component, easy processed, flexible and water-repellent featured joint filling mortar that forms a smooth surface and used in 3-6 mm joints.

APPLICATION AREASIt is used for filling the joint gaps up to 6 mm of granite, ceramic, tile, marble, sto-ne and similar coating materials on the horizontal and vertical surfaces in indoors (bathroom, toilet, kitchen, sauna, etc.) and outdoors (pool).

SURFACE PREPARATIONTo ensure a uniform color and desiccation, dust, sawdust, construction cement debris and so on that may be available in the joint gaps should be scraped by using a thin rod and be cleaned with a brush before the joint application process. The joint gaps especially on the walls should be dampened moisturized before the application. In order to prevent the tiles to get loose, it should be noticed that they are firmly adhered; accordingly the adherence is dried completely.

APPLICATION CONDITIONSIt should be considered that the ambient temperature is between +5 oC to +35 oC during the application. It should not be applied for the frozen, melting surfaces or the surfaces that is at the risk of frost within 24 hours. It should not be applied under direct sunlight and strong wind. Joint application process must be comple-ted 48 hours prior to laying tiles.

IMPLEMENTATION7.2 to 8 liters of water per 20 kg of Fixkim Flex Joint Filling Mortar shall be mixed thoro-ughly with preferably a low-speed mixer or trowel until getting a lump-free homogenous mixture. After the joint filling mortar is allowed to stand for 5 minutes, it should be mixed again for 1 to 2 minutes before the application. The mortar shall be filled in the joint gaps with the hard rubber squeegee or the hard rubber base grouting spreading trowel. In or-der to fill the gaps well, the mortar should be trowelled previously parallel and then cross to the joints. The excess amount of the mortar on the surface shell be peeled off with a soft tipped spatula or moistened sponge-tipped spatula. After waiting for 15 to 30 mi-nutes depending on ambient temperature the thin layer of grout that may remain on the surface must be cleaned thoroughly by wiping with a damp sponge. Surface smoothing and cleaning process should be done with a dry cloth when the grouting mortar is wet.




TECHNICAL SPECIFICATIONS Appearance White or colored fine powder Powder Density 1200 ± 100 gr/lt. Water Mixing Ratio 7,2 - 8 lt. water / 20 kg. powder Pot Life Approximately 1,5 hours Water absorption after 30 min. - Water absorption after 240 min. ≤ 2 - ≤ 5 Curing Time 12 hours Commissioning Time 24 hour for wall, 48 hours on the ground Bending Strength > 4 N/mm2 (EN 12808-3) Pressure Strength > 17 N/mm2(EN 12808-3) Abrasion Resistance < 1000 mm3 (EN 12808-2) Shrinkage < 3 mm/m. (EN 12808-4)Bending Strength After Freezing unsolved Min. 4 N/mm2 (EN 12808-3)Related standard CG2W ( TS EN 13888 )


COLOR

44

Consumption Consumption according to the joint width (gr/m2)Tile sizes ( cm x cm) 6 mm 10 mm 20 mm10 x 10 1500 2100 420020 x 20 700 1050 210030 x 30 500 700 1400

DESCRIPTIONIt is the cement-based, polymer blended, high-performance, single-component, easy processed, joint filling mortar that forms a smooth surface and used in 6-20 mm grouts.

APPLICATION AREASIt is used for filling the joint gaps up to 20 mm of granite, ceramic, tile, marble, stone and similar coating materials indoors, horizontal and vertical surfaces.

SURFACE PREPARATIONTo ensure a uniform color and desiccation, dust, sawdust, construction cement deb-ris and so on that may be available in the joint gaps should be scraped by using a thin rod and be cleaned with a brush before the joint application process. The joint gaps especially on the walls should be dampened moisturized before the application. In order to prevent the tiles to get loose, it should be noticed that they are firmly adhered; accordingly the adherence is dried completely.


IMPLEMENTATION4.4 to 5.6 liters of water per 20 kg of Fixkim Joint Filling Mortar for Extensive Grouts shall be mixed thoroughly with preferably a low-speed mixer or trowel until getting a lump-free homogenous mixture. After the joint filling mortar is allowed to stand for 5 minutes, it should be mixed again for 1 to 2 minutes before the application. The mortar shall be filled in the joint gaps with the hard rubber squeegee or the hard rubber base grouting spreading trowel. In order to fill the gaps well, the mortar should be trowelled previously parallel and then cross to the joints. The excess amount of the mortar on the surface shell be peeled off with a soft tipped spatula or moistened sponge-tipped spatula. After waiting for 30 to 60 minutes depending on ambient temperature the thin layer of grout that may remain on the surface must be cleaned thoroughly by wiping with a damp sponge. Surface smoothing and cleaning process should be done with a dry cloth when the grouting mortar is wet.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood coatings, metal coating and the surfaces exposed to the moisture. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.



TECHNICAL SPECIFICATIONS Appearance White or colored fine powder Powder Density 1350 ± 100 kg/m3 Water Mixing Ratio 4.4 – 5.6 lt. water / 20 kg. powder Pot Life Approximately 1,5 hours Application temperature Between +5 oC and 35 oC Curing Time 24 hours Water absorption after 30 min. - Water absorption after 240 min. ≤ 5 - ≤ 10 Commissioning Time 24 hour for wall, 48 hours on the ground Bending Strength > 4 N/mm2 (EN 12808-3) Pressure Strength > 20 N/mm2 (EN 12808-3) Abrasion Resistance < 1000 mm3 (EN 12808-2) Shrinkage < 3 mm/m. (EN 12808-4) Shelf Life 6 months in dry conditions Related standard CG2A ( TS EN 13888 )

FLEX EXTENSIVE JOINT FILLING MORTAR

COLOR

45

SILICONE JOINT FILLING MORTAR

DESCRIPTIONIt is the cement-based, high-performance, single-component, easy processed and flexible silicone joint filling mortar that forms a smooth surface and used in 3-6 mm joints.

APPLICATION AREASIt is used for filling the joint gaps up to 6 mm of granite, ceramic, tile, marble, sto-ne and similar coating materials on the horizontal and vertical surfaces in indoors (bathroom, toilet, kitchen, sauna, etc.) and outdoors (pool).



IMPLEMENTATION7.2 to 8 liters of water per 20 kg of Fixkim Silicone Joint Filling Mortar shall be mixed thoroughly with preferably a low-speed mixer or trowel until getting a lump-free homo-genous mixture. After the joint filling mortar is allowed to stand for 5 minutes, it should be mixed again for 1 to 2 minutes before the application. The mortar shall be filled in the joint gaps with the hard rubber squeegee or the hard rubber base grouting spreading trowel. In order to fill the gaps well, the mortar should be trowelled previously parallel and then cross to the joints. The excess amount of the mortar on the surface shell be peeled off with a soft tipped spatula or moistened sponge-tipped spatula. After waiting for 15 to 30 minutes depending on ambient temperature the thin layer of grout that may remain on the surface must be cleaned thoroughly by wiping with a damp sponge. Sur-face smoothing and cleaning process should be done with a dry cloth when the grouting mortar is wet.




TECHNICAL SPECIFICATIONS Appearance White or colored fine powder Powder Density 1200 ± 100 gr/lt. Water Mixing Ratio 7,2 - 8 lt. water / 20 kg. powder Pot Life Approximately 1,5 hoursWater absorption after 30 min. - Water absorption after 240 min. ≤ 2 - ≤ 5 Curing Time 12 hours Commissioning Time 24 hour for wall, 48 hours on the ground Bending Strength > 3.5 N/mm2 (EN 12808-3) Pressure Strength > 18 N/mm2 (EN 12808-3) Abrasion Resistance < 1000 mm3 (EN 12808-2) Shrinkage < 3 mm/m. (EN 12808-4) Bending Strength After Freezing unsolved Min. 3.5 N/mm2 (EN 12808-3) Related standard CG2WA ( TS EN 13888 )


COLOR

46


DESCRIPTIONIt is the cement-based, high-performance, single-component, easy processed, fle-xible and antibacterial silicone joint filling mortar that forms a smooth surface and used in 3-6 mm joints.

APPLICATION AREASIt is used for filling the joint gaps up to 6 mm of granite, ceramic, tile, marble, sto-ne and similar coating materials on the horizontal and vertical surfaces in indoors (bathroom, toilet, kitchen, sauna, surgery rooms, restaurants and all food industry) and outdoors (pool).



IMPLEMENTATION7.2 to 8 liters of water per 20 kg of Fixkim Antibacterial Silicone Joint Filling Mortar shall be mixed thoroughly with preferably a low-speed mixer or trowel until getting a lump-free homogenous mixture. After the joint filling mortar is allowed to stand for 5 minutes, it should be mixed again for 1 to 2 minutes before the application. The mortar shall be filled in the joint gaps with the hard rubber squeegee or the hard rubber base grouting spreading trowel. In order to fill the gaps well, the mortar should be trowelled previously parallel and then cross to the joints. The excess amount of the mortar on the surface shell be peeled off with a soft tipped spatula or moistened sponge-tipped spatula. After waiting for 15 to 30 minutes depending on ambient temperature the thin layer of gro-ut that may remain on the surface must be cleaned thoroughly by wiping with a damp sponge. Surface smoothing and cleaning process should be done with a dry cloth when the grouting mortar is wet.




TECHNICAL SPECIFICATIONS Appearance White or colored fine powder Powder Density 1200 ± 100 gr/lt. Water Mixing Ratio 7,2 - 8 lt. water / 20 kg. powder Pot Life Approximately 1,5 hours Water absorption after 30 min. - Waterabsorption after 240 min. ≤ 2 - ≤ 5 Curing Time 12 hours Commissioning Time 24 hour for wall, 48 hours on the ground Bending Strength > 3.5 N/mm2 (EN 12808-3) Pressure Strength > 18 N/mm2 (EN 12808-3) Abrasion Resistance < 1000 mm3 (EN 12808-2) Shrinkage < 3 mm/m. (EN 12808-4) Bending Strength After Freezing unsolved Min. 3.5 N/mm2 (EN 12808-3) Related standard CG2WA ( TS EN 13888 )

ANTIBACTERIAL SILICONE JOINT FILLING MORTAR

COLOR

47

EPOXY BASED JOINT FILLING MORTAR

48

DESCRIPTIONIt is used in all kinds of ceramic, tile, porcelain, glass mosaic applications.

APPLICATION AREASIt is used in the places where the cement based joint filling mortars are not suitable for use because of the chemical effects; such as factories engaged in food and beve-rage industry, canteens, kitchens, swimming pools, spas and so on.

SURFACE PREPARATION AND APPLICATIONThe materials that prevent the adherence such as form oil, dust, paint, dirt, etc. should be removed from the surface to be applied. The product is applied to the joint gaps to be intended by mixing the components A and B. The product should be mixed thoroughly; no additional supplement should be added externally.


CONSUMPTIONThe amount of consumption depends on the tile size

10 x 10 cm: approximately 0,45 kg/m2

15 x 15 cm: approximately 0,30 kg/m2

STORAGEIt can be stored in the indoor conditions at +5 oC to +30 oC in its original packaging for a period of one year. They should be stored maximum three rows one on the top of the other.

SAFETY WARNINGSR10: FlammableR20-21-22: It is harmful in case of inhalation, swallowing and in contact with skin.S2: Keep out of the reach of children.S20-21: Do not eat or drink when you are working.S24-25: Keep away from contact with eyes and skin.S26: In case of contact with eyes, rinse plenty of water and seek medical advice.S36-37-39 Wear suitable protecting clothing, gloves, goggles and face protection mask when you are working.S-36: It is irritative for eyes.S-38: It irritates the skin.S-42: It may cause sensitization by inhalation.

TECHNICAL SPECIFICATIONS Color White, gray Density 1,50 kg/lt Application temperature Between +5 oC and 35 oC Running time 60 minutes at 25 oC Surface drying time 60-90 minutes at 25 oC Packaging 5+1 kg Application Trowel Cleaning the instruments used in It shall be cleaned with its special thinner Diluent It shall be used without dilution

COLOR

Consumption Consumption according to the joint width (gr/m2)Tile sizes ( cm x cm) 8 mm 10 mm19 x 19 1000 125024 x 24 800 1000

DESCRIPTIONIt is the cement-based, high-performance, single-component and easy processed glass brick joint filling mortar that forms a smooth surface and used in 3-10 mm joints.

APPLICATION AREASIt is used for filling the joint gaps up to 10 mm of glass brick and similar coating ma-terials on the horizontal and vertical surfaces in indoors,.

SURFACE PREPARATIONTo ensure a uniform color and desiccation, dust, sawdust, construction cement deb-ris and so on that may be available in the joint gaps should be scraped by using a thin rod and be cleaned with a brush before the joint application process. The joint gaps especially on the walls should be dampened moisturized before the application. In order to prevent the glass bricks to get loose, it should be noticed that they are firmly adhered; accordingly the adherence is dried completely.


IMPLEMENTATION5.6 to 6.4 liters of water per 20 kg of Fixkim Glass Brick Joint Filling Mortar shall be mixed thoroughly with preferably a low-speed mixer or trowel until getting a lump-free homogenous mixture. After the joint filling mortar is allowed to stand for 5 mi-nutes, it should be mixed again for 1 to 2 minutes before the application. The mortar is rendered to the consistency of paste by kneading by hand. The pasty mortar that formed into the shape of cylinder at the desired joint thickness shall be filled into the joint gap. The excess amount of the mortar on the surface shell be peeled off with a soft tipped spatula or moistened sponge-tipped spatula. After waiting for 15 to 30 minutes depending on ambient temperature the thin layer of grout that may remain on the surface must be cleaned thoroughly by wiping with a damp sponge. Surface smoothing and cleaning process should be done with a dry cloth when the grouting mortar is wet.




TECHNICAL SPECIFICATIONS Appearance White or colored fine powder Powder Density 1200 ± 100 gr/lt. Water Mixing Ratio 5.6 – 6.4 lt. water / 20 kg. powder Pot Life Approximately 1 hour Water absorption after 30 min. Max. 2 gr. Curing Time 12 hours Commissioning Time 24 hour for wall, 48 hours on the ground Bending Strength > 2 N/mm2 (EN 12808-3) Pressure Strength > 13 N/mm2 (EN 12808-3) Abrasion Resistance < 200 mm3 (EN 12808-2) Shrinkage < 2 mm/m. (EN 12808-4) Bending St rength After Freezing unsolved Min. 2 N/mm2 (EN 12808-3)

GLASS BRICK JOINT FILLING MORTAR

COLOR

49

FIBRATED THICK REPAIR MORTAR

FIBRATED/NON-FIBRATED THIN REPAIR MORTAR

QUICK SETTING THICK REPAIR MORTAR

QUICK SETTING THIN REPAIR MORTAR

FIX-MORTAR

ANCHORAGE AND FIXING MORTAR

NON-SHRINK GROUT MORTAR

FLUID GROUT MORTAR

SC 215 ANCHORAGE MORTAR


REPAIR AND STRENGTHENING

MORTARS

52

FIBRATED THICK REPAIR MORTAR

DESCRIPTIONIt is the cement-based, single-component, fibrated mortar with thick aggregate for filling and smoothing surface.

APPLICATION AREASIt is used for filling the large cracks and gaps on the surfaces of cement plaster cei-lings, walls and floors. In particular, it is applied in a thin layer for repairing the sur-faces of exposed concrete and reinforced concrete elements and for removing the molding errors. It is ideal for achieving a clean surface under the ceramic, granite, natural stone and similar coatings in the restoration processes.


SURFACE PREPARATIONThe surface must be clean, dry and free from the mold oils. For detection of the law adherent grounds, it should be checked with the help of hammer. The loose parts should be removed from the ground and open corners should be left at the edges of the place to be repaired. Rusted reinforced bars must be opened completely. The surface must be damped prior to the application and should be saturated with the water in very hot and windy weather conditions. APPLICATION FEATURESApplication thickness: 2 cm, the time to wait between the layers: an average of 3 hours. Commissioning time: approximately 24 hours (+20 oC). Complete curing time: 28 days (+20 oC)

IMPLEMENTATION25 kg Fixkim Thick Repair Mortar shall be poured into 4.5 – 5.5 liters of clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and made ready by mixing again. The mortar shall be applied to the surface with a steel trowel. If the application is made more than one, you should wait for 3 hours between the layers and the surface must be dampened before passing to the application of the next layer. The surface must be polished at least 2 hours later and plastic trowel and damp sponge should be used for very smooth surfaces. The surface must be dampened in 2-3 days after the application.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTION1.6 – 1.8 kg/m3 (for 1 mm of layer thickness)


TECHNICAL SPECIFICATIONS Appearance Gray colored fine powder Powder Density 1550 ± 100 kg/m3

Water Mixing Ratio 4.5 – 5.5 lt. water / 25 kg. powder Pot Life Approximately 2 hours Application temperature Between +5 oC and +35 oC Commissioning Time 24 hour for wall, 48 hours for the ground Bending Strength > 4 N/mm2

Compressive Strength > 12 N/mm2

Adhesion Resistance > 0.5 N/mm2

Shelf-life 6 months in dry conditions

53

FIBRATED/NON-FIBRATED THIN REPAIR MORTAR

DESCRIPTIONIt is the cement-based, single-component, fibrated mortar with thin aggregate for filling and smoothing surface.

APPLICATION AREASIt is used for filling the cracks and gaps on the surfaces of cement plaster ceilings, walls and floors. In particular, it is applied in a thin layer for repairing the surfaces of exposed concrete and for removing the molding errors. It is ideal for achieving a clean surface under the ceramic, granite, natural stone and similar coatings in the restoration processes.


SURFACE PREPARATIONConcrete surfaces: The surface must be clean, dry and free from the mold oils. For detection of the low adherent grounds, it should be checked with the help of ham-mer. The loose parts should be removed from the ground and open corners should be left at the edges of the place to be repaired. Rusted reinforcing bars must be opened completely. The surface must be damped prior to the application and should be saturated with the water in very hot and windy weather conditions.Reinforcing bars: The rusts on the bars must be cleaned with the help of steel wire brush and the dust must be removed. Contact between the reinforcing bars and the concrete should be interrupted and 2 layers of anti-corrosion paint should be applied. Then, adherence primer should be used. After the adherence primer is dried, the fibrated thin repair mortar should be applied on it.

APPLICATION FEATURESApplication thickness: 3-5 mm, the time to wait between the layers: an average of 3 hours. Commissioning time: approximately 24 hours (+20 oC). Complete curing time: 28 days (+20 oC)

IMPLEMENTATION25 kg Fixkim Fibrated Thin Repair Mortar shall be poured into 5.5 – 6 liters of cle-an water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mixture shall be allowed to stand for 5 minutes and made ready by mixing again. The surface should be dampened with water. The application must be performed after hydration. In order to increase the adherence in the smooth surfa-ces, it should be applied to the surface with Fixkim general purpose or gross primer brush and the application is commenced before it is dried. The mortar shall be app-lied to the surface with a steel trowel. For the smooth and uniform surfaces, the surface should be smoothed through the use of a plastic trowel or a damp sponge. The surface must be dampened in 2-3 days after the application. The application thickness: 3-5 mm. The application should be made 2 times in thicker applications.


CONSUMPTION1.4 kg/m2 (for 1 mm of layer thickness)



Water Mixing Ratio 5.5 – 6 lt. water / 25 kg. powder Pot Life Approximately 30 minutes Application temperature Between +5 oC and 35 oC Commissioning Time 24 hours for wall, 48 hours for the ground Bending Strength > 3 N/mm2


Adhesion Resistance > 0.5 N/mm2


54

QUICK SETTING THICK REPAIR MORTAR

DESCRIPTIONIt is the cement-based, single-component, quick setting and high strength mortar including 0 to 2 mm of aggregate and not being shrinkages.

APPLICATION AREASIt is used for repairing the interiors and exteriors of the reinforced concrete cons-truction and repairing the concretes and equipment which are damaged as a result of the erosion of the reinforced bars. It is also applied in repairing the concrete floors exposed to the pedestrian and vehicle traffic, in the repairs that requires high early strength, in filling the gaps around the installation pipe and elements, in fixing the machine frames and in repairing the manhole covers.

SURFACE PREPARATIONConcrete surfaces: The surface must be clean, dry and free from the mold oils. For detection of the low adherent grounds, it should be checked with the help of ham-mer. The loose parts should be removed from the ground and open corners should be left at the edges of the place to be repaired. Rusted reinforcing bars must be opened completely. The surface must be damped prior to the application and should be saturated with the water in very hot and windy weather conditions.Reinforcing bars: The rusts on the bars must be cleaned with the help of steel wire brush and the dust must be removed. Contact between the reinforcing bars and the concrete should be interrupted and 2 layers of anti-corrosion paint should be applied. Then, adherence primer should be used. After the adherence primer is dried, the thick repair mortar should be applied on it.


APPLICATION FEATURESApplication thickness: 2 cm, the time to wait between the layers: an average of 2 hours.Commissioning time: approximately 12 hours (+20 oC). Complete curing time: 28 days (+20 oC)

IMPLEMENTATION25 kg Fixkim Quick Setting Thick Repair Mortar shall be poured into 5 – 6 liters of clean water and mixed with a low-speed mixer until getting a lump-free homoge-nous mixture. The mixture shall be allowed to stand for 5 minutes prior to the app-lication and made ready by mixing again. The mortar shall be applied to the surface with a steel trowel. If the application is made more than one, you should wait for 2 hours between the layers and the surface must be dampened before passing to the application of the next layer. The surface must be polished at least 2 hours later and plastic trowel and damp sponge should be used for very smooth surfaces. The surface must be dampened in 2-3 days after the application. The quick setting thick repair mortar should be prepared in small amounts by taking into consideration its application rate.


CONSUMPTION1.6 – 1.8 kg/m2 (for 1 mm of layer thickness)



Water Mixing Ratio 5 – 6 lt. water / 25 kg. powder Pot Life Approximately 15 minutes Application temperature Between +5 oC and 35 oC Commissioning Time 24 hours for wall, 48 hours for the ground Bending Strength > 7 N/mm2


Adhesion Resistance > 1 N/mm2


55

QUICK SETTING THIN REPAIR MORTAR

DESCRIPTIONIt is the cement-based, single-component, quick setting, thin aggregate and fiber reinforced, high strength mortar not doing shrinkages.

APPLICATION AREASIt is used for repairing the interiors and exteriors of the reinforced concrete cons-truction and repairing the concretes and equipment which are damaged as a result of the erosion of the reinforced bars. It is also applied in repairing the concrete floors exposed to the pedestrian and vehicle traffic, in the repairs that requires high early strength, in filling the gaps around the installation pipe and elements.

SURFACE PREPARATIONConcrete surfaces: The surface must be clean, dry and free from the mold oils. For detection of the low adherent grounds, it should be checked with the help of ham-mer. The loose parts should be removed from the ground and open corners should be left at the edges of the place to be repaired. Rusted reinforcing bars must be opened completely. The surface must be damped prior to the application and should be saturated with the water in very hot and windy weather conditions.Reinforcing bars: The rusts on the bars must be cleaned with the help of steel wire brush and the dust must be removed. Contact between the reinforcing bars and the concrete should be interrupted and 2 layers of anti-corrosion paint should be applied. Then, adherence primer should be used. After the adherence primer is dried, the fibrated thin repair mortar should be applied on it.


APPLICATION FEATURESApplication thickness: 3-5 mm, the time to wait between the layers: 2 hours Commissioning time: approximately 12 hours (+20 oC), complete curing time: 28 days (+20 oC)

IMPLEMENTATION25 kg Fixkim Quick Setting Fibrated Thin Repair Mortar shall be poured into 6 – 6.5 liters of clean water and mixed with a low-speed mixer until getting a lump-free ho-mogenous mixture. The mixture shall be allowed to stand for 2 minutes prior to the application and made ready by mixing again. The surface should be saturated with water. After saturation the application should be performed. In order to increase the adherence in the smooth surfaces, it should be applied to the surface with Fixkim general purpose or gross primer brush and the application is commenced before it is dried. The mortar shall be applied to the surface with a steel trowel. For the flat and smooth surfaces, the surface should be smoothed through the use of plastic trowel and do. 2-3 days after the application the surface should be dampened.





Water Mixing Ratio 6 – 6.5 lt. water / 25 kg. powder Pot Life Approximately 15 minutes Application temperature Between +5 oC and 35 oC Commissioning Time 12 hours for wall, 24 hours for the ground Bending Strength > 7 N/mm2(28 day) Compressive Strength > 30 N/mm2 (28 day) Adhesion Resistance > 1 mm2 (28 day) Shelf-life 6 months in dry conditions

DESCRIPTIONIt is the cement-based, ready-mixed concrete material that consists of homogeno-us mixture of various aggregates and mineral additives and becomes harden when it reacts with water.

APPLICATION AREASIt is used for restoration and reconstruction processes; repairing the concrete and exposed concrete elements; bearing the entrances, floors, ground floors, terraces, garage and garage gates of houses and apartments, structural elements of agri-cultural buildings, livestock farms, agricultural product warehouses and stacking areas, roads, parks, bike paths, pedestrian sidewalks. The Fix-Mortar provides high tensile and bending strength compared with the standard concrete.

SURFACE PREPARATIONThe materials that would prevent the adherence such as mold oil, dust, pant, dirt, etc. should be removed from the application surface. The surface should be dampe-ned before the application. It should be applied together with the exposed concrete primer in the exposed concrete surfaces which have the surface smoothness and brightness.


APPLICATION FEATURESBy means of a large amount of uniformly distributed synthetic fibers, the risk of shrinkage cracks caused by tensile/shrinking is lower compared to non-fibrous concrete. The synthetic fiber in its structure form a network within the concrete against cracks and increases the tensile and bending strength by distributing the load applied to the concrete.

IMPLEMENTATIONBefore starting to use, the application area should be moistened. By using the scre-ed spiral with hand, the mortar which was prepared with plaster machine and scre-ed machine (5.5. – 6.5 liters of water / 25 kg bag) is laid to the surface in 1-3 cm thickness and leveled. When the surface is hardened, smoothing process is done by mechanical polishing. The surface must be dampened after a day of practice in 7 days intervals for high performance. Since the fix-mortar contains synthetic fibers, it should be handled by the notched tools like rake and similar rather than shovel. It is extremely important to protect the homogenous distribution of synthetic fibers in the concrete. Although the load applied to the concrete is distributed to all the mass by means of the networks formed by the synthetic fibers, equipment and special reinforcements are necessary for the special points such as the places to be planted poles in synthetic fibrous concrete too. Surface finishing and curing applications are the same as the standard concrete. The concrete must be protected against sudden temperature changes, torrential rain, vibrations and shocks endanger the building until the concrete hardens enough. After pouring the concrete, wrapping with a wet cloth or curing application to prevent the evaporation and sudden water loss is cru-cial to reduce the risk of cracking.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In terms of durability of the product, the surface should be watered regularly in 7 days after the application. Plaster mesh is recommended in the diffe-rent material joints and the points where any movement may be seen. Depending on the ambient temperature, for the applications to be made on the machine plaster, you should wait at least 15 days. Do not violate the conditions for the specified app-lication surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Beca-use it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTION15 - 17 kg/m2 (for 1 mm of thickness)




Water Mixing Ratio 5.5 – 6.5 lt. water / 25 kg. powderApplication temperature Between +5 oC and 35 oCAbrasion Strength 5 cm3 / 50 cm2 by the Bohme methodHardness 5 Mohs.Compressive Strength > 12 N/mm2


Packing 25 kg foil kraft paper bag Shelf-life 8 months in dry conditions

56

FİX-MORTAR

DESCRIPTIONIt is the cement-based, self-leveling, non-shrink, fine aggregate, high strength re-pair and anchoring mortar providing high level initial and final strengths.

APPLICATION AREASIt is used for securely fixing the machines running with high power and pressure such as crane, lift, printing and textile machines to the ground; fixing the traffic lights, road signs and poles, bridge parapets and safety bars in road and bridge connections, placing the sewage and channel plates, filling the connection and bed around, in the connection point of steel and concrete in construction of the steel buildings. It is also applied in repairing the concrete floors exposed to the vehicle and pedestrian traffic and in repairs that early and high strength is required. It is highly fluid and compressive and flexural strength values are reached in a short time.

SURFACE PREPARATIONThe surface must be clean, dry and free from the mold oils. For detection of the law adherent grounds, it should be checked with the help of hammer. The loose parts should be removed from the ground and open corners should be left at the edges of the place to be repaired. Rusted reinforced bars must be opened completely. The surface must be damped prior to the application and should be saturated with the water in very hot and windy weather conditions. The machine bases should be pla-ced and leveled.


APPLICATION FEATURESApplication thickness: 5 mm – 40 mm, the time to wait between the layers: 2 hours Commissioning time: approximately 12 hours (+20 oC). Complete curing time: 28 days (+20 oC)

IMPLEMENTATION25 kg Fixkim Fast Setting Fine Fluid Anchor Mortar shall be poured into 5 – 6 liters of clean water and mixed with a low-speed mixer until getting a lump-free homo-genous mixture. The mortar shall be applied to the surface with a steel trowel. The surface must be smoothed by using the plastic trowel or damp sponge for uniform and smooth surfaces. The surface must be dampened for 2-3 days after the appli-cation. In the anchoring processes, pouring thickness should be between 5 mm and 40 mm in a time.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.CONSUMPTION1.4 kg/m2 (for 1 mm of layer thickness)



Water Mixing Ratio 5 – 6 lt. water / 25 kg. powder Pot Life Approximately 15 minutes Application temperature Between +5 oC and 35 oC Commissioning Time 12 hour for wall, 24 hours for the ground Bending Strength > 7 N/mm2 (28 day) Compressive Strength > 40 N/mm2 (28 day) Adhesion Resistance > 1N/mm2 (28 day) Shelf-life 6 months in dry conditions

ANCHORAGE AND FIXING MORTAR

57

NON-SHRINK GROUT MORTAR

58

DESCRIPTIONIt is the cement-based, self-leveling, water resistant, non-shrink, high strength re-pair and filling mortar providing high level initial and final strengths.

APPLICATION AREASIt is used for anchoring the machine bases, in repairs that early and high strength is required, in high bearing capacity beddings and in bedding the bearing elements, in road and bridge connections, in fixing the traffic lights, road signs and poles, bridge parapets and safety bars, in placing the sewage and channel plates and filling the connection and bed around, in the connection point of steel and concrete in cons-truction of the steel buildings. It is also applied in repairing the concrete floors ex-posed to the vehicle and pedestrian traffic, for raising the manhole and manhole co-vers, for fixing the cups and paving stones. It reaches the compressive and flexural values in a short time and it is fluid.

SURFACE PREPARATIONThe surface must be clean; dirt, dust and loose particles should be removed. The application vessel must be fixed, sealed and dried very well. If the application shall be made on the old concrete, the surface must be dampened before the application. Small bodies of water should be avoided. The material to be used should be prepared by taking into account of the running time.


APPLICATION FEATURESPot life: Approximately 10-15 minutes (varies depending the temperature).Application thickness: minimum 5 mm and maximum 40 mm; the time to wait betwe-en the layers: 1 hour. Commissioning time: approximately 6 hours (+20 oC). Complete curing time: 28 days (+20 oC).

IMPLEMENTATION Bag of 25 kg Fixfast Fast Setting Fluid Grout Mortar should be poured slowly into average of 5 – 5.5 liters of clean water and mixed for 3-4 minutes with a low-speed mixer until getting a lump-free homogenous mixture. Water should not be added into the setting mortar. The grout in fluid form should be poured from one side of the form that was prepared previously. So air jams into the mortar should be avo-ided. In order to achieve filling of all cavities in the mold, placing should be made by using a steel wire that its tip has been formed as a hook. Never use the vibrator. The surfaces exposed to the external weather conditions should be protected against the solar rays and wind by covering with the curing blanket for 48 hours. The equip-ment should be cleaned with water after the application when the material is fresh. The specified times are valid for in 20 °C of surface and ambient temperature; the period increases at low temperature and it decreases in higher temperatures. The surface should be dampened for 2-3 days after the application.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood coatings, metal coatings and on the surfaces exposed to the moisture. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The pac-kaged products should not be stored in humid conditions.





Water Mixing Ratio 5 – 5.5 lt. water / 25 kg. powder Pot Life Max. 15 minutes Commissioning Time 6 hours Wet Unit Weight 2000 ± 100 Kg. / m3

Adhesion Resistance >1.4 N/mm2 (28 days) Compressive Strength > 40 N/mm2 (28 days) Bending Strength > 10 N/mm2 (28 days)

FLUID GROUT MORTAR

59

DESCRIPTIONIt is the cement-based, self-leveling, water resistant, non-shrink, high strength repa-ir and filling mortar providing high level initial and final strengths.

APPLICATION AREASIt is used for anchoring the machine bases, in repairs that early and high strength is required, in high bearing capacity beddings and in bedding the bearing elements, in road and bridge connections, in fixing the traffic lights, road signs and poles, bridge parapets and safety bars, in placing the sewage and channel plates and filling the con-nection and bed around, in the connection point of steel and concrete in construction of the steel buildings. It is also applied in repairing the concrete floors exposed to the vehicle and pedestrian traffic, for raising the manhole and manhole covers, for fixing the cups and paving stones. It reaches the compressive and flexural values in a short time and it is fluid.

SURFACE PREPARATIONThe surface must be clean; dirt, dust and loose particles should be removed. The appli-cation vessel must be fixed, sealed and dried very well. If the application shall be made on the old concrete, the surface must be dampened before the application. Small bo-dies of water should be avoided. The material to be used should be prepared by taking into account of the running time.

APPLICATION CONDITIONSIt should be considered that the ambient temperature is between +5 oC to +35 oC du-ring the application. It should not be applied for the frozen, melting surfaces or the surfaces that is at the risk of frost within 24 hours. It should not be applied under direct sunlight and strong wind.

APPLICATION FEATURESPot life: Approximately 15-20 minutes (varies depending the temperature).Application thickness: minimum 5 mm and maximum 40 mm; the time to wait between the layers: 1.5 hour. Commissioning time: approximately 12 hours (+20 oC). Complete curing time: 28 days (+20 oC).

IMPLEMENTATION Bag of 25 kg Fixfast Fluid Grout Mortar should be poured slowly into average of 5 – 5.5 liters of clean water and mixed for 3-4 minutes with a low-speed mixer until getting a lump-free homogenous mixture. Water should not be added into the set-ting mortar. The grout in fluid form should be poured from one side of the form that was prepared previously. So air jams into the mortar should be avoided. In order to achieve filling of all cavities in the mold, placing should be made by using a steel wire that its tip has been formed as a hook. Never use the vibrator. The surfaces expo-sed to the external weather conditions should be protected against the solar rays and wind by covering with the curing blanket for 48 hours. The equipment should be cleaned with water after the application when the material is fresh. The specified times are valid for in 20 °C of surface and ambient temperature; the period increases at low temperature and it decreases in higher temperatures. The surface should be dampened for 2-3 days after the application.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood coatings, metal coatings and on the surfaces exposed to the moisture. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The pac-kaged products should not be stored in humid conditions.





Water Mixing Ratio 5 – 5.5 lt. water / 25 kg. powder Pot Life Max. 20 minutes Commissioning Time After 12 hours Wet Unit Weight 2000 ± 100 Kg. / m3

Compressive Strength > 25 N/mm2 (28 days) Adhesion Resistance > 1 N/mm2 (28 days) Bending Strength > 7 N/mm2 (28 days)


60

DESCRIPTIONIt is two-component, solvent-free, epoxy resin based repair and installation mortar.Public-works pos. no. 04.613/8-e

APPLICATION AREASIt is used in repair, installation and insulation of the cracks; and in bonding the cera-mic and concrete assembly.

BENEFITS-Solvent-free-Easy to use-Excellent adhesion to concrete-Chemical resistance-Mechanical strength

SURFACE PREPARATIONThe loose particles and paint residues on the surface should be cleaned completely, breaks and cracks should be repaired, the surfaces should be roughened and dust, oils, dirt and rust (steel surfaces) should be removed from the surfaces.

MIXTURE PREPARATIONA and B components should be mixed at least 3-4 minutes with a spatula, trowel or low-speed mixer until obtaining a homogenous mixture by considering the mixing ratios.

APPLICATION CONDITIONSThe surfaces should have adequate strength. The compressive strength of the conc-rete must be at least 25 N/mm2, tensile strength must be at least 1,5 N/mm2. - Do not apply below 10 oC and in very humid environments.- Mixing ratios should be considered.

SAFETYThe product is for professional use. Please note the safety instructions on the pac-kage before using, if necessary, see the Material Safety Data Sheet. Avoid inhalation, avoid contact with skin and eyes, do not swallow and use the appropriate occupa-tional safety equipment. Take the necessary measures to prevent the pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas.

HANDLING AND STORAGE-The product should be stored between 5 to 35 oC.-The product should not be exposed to direct sunlight.-Opened product should be maintained in its packaging and by closing the cover firmly.

NOTEFİXKİM reserves the right to make development/revision in the product and this technical document in time. This Technical Data Sheet invalidates the previously published Technical Data Sheet for this product and is valid for 5 years. The user must make sure that the technical document in his hand is the most current version of the document, if necessary; he should check the timeliness of the document by questioning the company. It is under the responsibility of the practitioner weather the product is used in accordance with its purpose and the validity of the application conditions and application aims. FİXKİM Epoxy Paint does not accept any guarantee request on direct or indirect losses and damages, work accidents regarding the re-sults arising from implementation of the product as recommended. The packaging values reported above are the nominal values in standardized formulas by FİXKİM. Under normal production conditions, slight deviations may occur within the inter-national standards.

TECHNICAL SPECIFICATIONS Color Light Grey Appearance Dull Solids by Weight 100% Density 1,70 (±0.05) Packaging 4,75 Kg A Component + 0,25 Kg B Component = 5 Kg Mixture Ratio 19 / 1 Application Methods Spatula, Trowel Pot Life 40 minutes / 20 °C Shelf Life 1 year Time to wait between layers 24 hours / 20 °C Drying Time 12 hours at 20 °C Bending strength Min.17N/mm2 at 20 °C (1 Day) Min. 25N/mm2 at 20 °C (7 Days) Adhesion Strength (To steel) 6,50N/mm2 (7 Days) (Breakage from the concrete) 3,50N/mm2 (7 days ) Compressive Strength min.30/mm2 at 20 °C (1 Day) min.75N/mm2 at 20 °C (7 Days)


61

DESCRIPTIONIt is two-component, solvent-free, epoxy resin based repair, anchorage and instal-lation mortar.Public-works pos. no. 04.613/8-e

APPLICATION AREASIt is used in repair, installation and insulation of the cracks; in fixing the anchorage elements and in bonding the ceramic, metal, steel and concrete assembly.

BENEFITS-Solvent-free-Easy to use-Use on vertical surfaces without sagging-Excellent adhesion to metal, steel and concrete-Chemical resistance-Mechanical strength-Provides adherence between metal and concrete-During the ore planting it is easily wrapped to the iron and provides anticorrosive protection

SURFACE PREPARATIONThe loose particles and paint residues on the surface should be cleaned completely, breaks and cracks should be repaired, the surfaces should be roughened and dust, oils, dirt and rust (steel surfaces) should be removed from the surfaces.

MIXTURE PREPARATIONA and B components should be mixed at least 3-4 minutes with a spatula, trowel or low-speed mixer until obtaining a homogenous mixture by considering the mixing ratios.

APPLICATION CONDITIONSThe surfaces should have adequate strength. The compressive strength of the conc-rete must be at least 25 N/mm2, tensile strength must be at least 1,5 N/mm2. - Do not apply below 10 oC and in very humid environments.- Mixing ratios should be considered.

SAFETYThe product is for professional use. Please note the safety instructions on the pac-kage before using, if necessary, see the Material Safety Data Sheet. Avoid inhalation, avoid contact with skin and eyes, do not swallow and use the appropriate occupa-tional safety equipment. Take the necessary measures to prevent the pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas.

HANDLING AND STORAGE-The product should be stored between 5 to 35 oC.-The product should not be exposed to direct sunlight.-Opened product should be maintained in its packaging and by closing the cover firmly.

NOTEFİXKİM reserves the right to make development/revision in the product and this technical document in time. This Technical Data Sheet invalidates the previously published Technical Data Sheet for this product and is valid for 5 years. The user must make sure that the technical document in his hand is the most current version of the document, if necessary; he should check the timeliness of the document by questioning the company. It is under the responsibility of the practitioner weather the product is used in accordance with its purpose and the validity of the application conditions and application aims. FİXKİM Epoxy Paint does not accept any guarantee request on direct or indirect losses and damages, work accidents regarding the re-sults arising from implementation of the product as recommended. The packaging values reported above are the nominal values in standardized formulas by FİXKİM. Under normal production conditions, slight deviations may occur within the interna-tional standards.

TECHNICAL SPECIFICATIONS Color Light Grey Appearance Dull Solids by Weight 100% Density 1,70 (±0.05) Packaging 3,75 Kg A Component +1,25 Kg B Component = 5 Kg Mixture Ratio 3 / 1 Application Methods Spatula, Trowel Pot Life 40 minutes / 20 °C Shelf Life 1 year Time to wait between layers 24 hours / 20 °C Drying Time 12 hours at 20 °C Bending strength Min.17N/mm2 at 20 °C (1 Day) Min. 25N/mm2 at 20 °C (7 Days) A Adhesion Strength (To steel) 6,50N/mm2 (7 Days) (Breakage from the concrete) 3,50N/mm2 (7 days) Compressive Strength min.30/mm2 at 20 °C (1 Day) min.75N/mm2 at 20 °C (7 Days)

MACHINE PLASTER

HAND PLASTER

FIXTEK PLASTER

SATIN PUTTY

POWDER PRIMER

RESTORATION PLASTER

PLASTERS AND PUTTIES

MACHINE PLASTER

DESCRIPTIONIt is a cement-based, ready to use plastering mortar applied with a plastering machine.

APPLICATION FIELDSIt is used for plastering on bricks, aerated concrete, exposed concrete surfaces and on the walls.

SURFACE PREPARATIONThe materials that prevent adherence such as mold oil, dust, paint, dirt should be removed from the surface. The cracks and holes should be covered with Fixkim repair mortars. The surface must be dampened before application. On the aerated concrete and exposed concrete surfaces must be base coated 3 days before the application. The plaster should be applied after the previous base coating is dried (at least 72 hours). The previous base coating should be saturated at regular inter-vals for 3 days. On the exposed concretes with smooth and bright surfaces base coating process should be done together with the exposed concrete primer and after the base coating is dried the plastering application should be made.


APPLICATION FEATURESApplication Thickness: 1-2,5 cmFor the applications more than 2.5 cm the time to wait between the layers: 24 hours.

IMPLEMENTATIONFixkim machine plaster is mixed with the help of plaster mixing machine (8-9 lt. water and 40 kg mortar) and sprayed on the surface. Application thickness for one layer should be between 1 cm and 2,5 cm. If the thickness is greater than 2,5 cm, the second layer should be applied at the thickness of maximum 2-2,5 cm after the first layer has set. For a proper plaster application, special aluminum profiles should be used. The machine plaster sprayed as horizontal bands should be leveled with the special aluminum leveling profiles. Corner profiles should be used to prevent bre-akages in corners. After the plaster is sufficiently hardened surface application is finished with the help of a damp sponge.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mor-tar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In terms of durability of the product the surface should be dampened at regular distances within 7 days after the application. Plaster mesh is recommended in joints of different materials and on the points where movement can appear. For the applications to be made on the machine plaster, you should wait at least 15 days depending on the ambient temperature. Do not violate the conditi-ons for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the app-lication. The packaged products should not be stored in humid conditions.

CONSUMPTION14-16 kg/m2 (for thickness of 1 cm)



TECHNICAL SPECIFICATIONS Appearance Gray-colored fine powder Powder Density 1600 ± 100 kg/ m3

Water Mixing Ratio 8-9 lt. water / 40 kg. powder Application Temperature Between +5 °C and 35 °C Adherence Strength > 0,1 N/mm2

Slipping < 0,5 mm Compressive Strength > 6 N /mm2


Unit Weight in wet 1750 ± 100 kg/ m3

Thermal Conductivity 0,430 (W/mK - 23 °C) Skinning Time < 60 dk. 20 °C Shelf Life 8 moths in dry conditions

64

HAND PLASTER

DESCRIPTIONIt is a cement-based hand blaster that can be applied on brick, aerated concrete, pumice and briquette etc. walls in interiors and exteriors, and provides a comfor-table adhesion and application.

APPLICATION FIELDSIt is used for plastering on bricks, aerated concrete, briquette, exposed concrete surfaces and walls.

SURFACE PREPARATIONThe materials that prevent adherence such as mold oil, dust, paint, dirt should be removed from the surface. The cracks and holes should be covered with Fixkim repair mortars. The surface must be dampened before application. On the aerated concrete and exposed concrete surfaces must be base coated 3 days before the application. The plaster should be applied after the previous base coating is dried (at least 72 hours). The previous base coating should be saturated at regular inter-vals for 3 days. On the exposed concretes with smooth and bright surfaces base coating process should be done together with the exposed concrete primer and after the base coating is dried the plastering application should be made.


APPLICATION FEATURESApplication Thickness: 1-2,5 cmFor the applications more than 2.5 cm the time to wait between the layers: 24 hours.

IMPLEMENTATIONFixkim hand plaster is mixed with the help of mixer (8-9 lt. water and 40 kg mortar) and applied with a trowel. For a proper plaster application, special aluminum profiles should be used. Corner profiles should be used to prevent breakages in corners. The cement-based hand plaster applied as horizontal bands should be leveled with the special aluminum leveling profiles. When the plaster is sufficiently hardened (when pressed with a finger the plaster should not be caved) surface is come threadbare. The surface is finished with the help of a damp sponge. Application thickness for one layer should be between 1 cm and 2,5 cm. If the thickness is greater than 2,5 cm, the second layer should be applied at the thickness of maximum 2-2,5 cm after the first layer has set.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In terms of durability of the product the surface should be dam-pened at regular distances within 7 days after the application. Plaster mesh is re-commended in joints of different materials and on the points where movement can appear. For the applications to be made on the hand plaster, you should wait at least 15 days depending on the ambient temperature. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTION16 kg/m2 (for thickness of 1 cm)




Water Mixing Ratio 8-9 lt. water / 40 kg. powder Application Temperature Between +5 °C and 35 °C Adherence Strength > 0,1 N/mm2



Unit Weight in wet 1750 ± 100 kg/ m3

Thermal Conductivity 0,430 (W/mK - 23 °C) Skinning Time < 60 dk. 20 °C Shelf Life 8 moths in dry conditions

65

FIXTEK PLASTER

DESCRIPTIONIt is a cement-based blaster that can be applied by hand or machine on brick, aera-ted concrete, pumice and briquette etc. walls in interiors and exteriors, and provides a comfortable adhesion and application.

APPLICATION FIELDSIt is used for plastering on bricks, aerated concrete, briquette, exposed concrete surfaces and walls.

SURFACE PREPARATIONThe materials that prevent adherence such as mold oil, dust, paint, dirt should be removed from the surface. The cracks and holes should be covered with Fixkim re-pair mortars. The surface must be dampened before application. On the aerated concrete and exposed concrete surfaces must be base coated 3 days before the application. The plaster should be applied after the previous base coating is dried (at least 72 hours). The previous base coating should be saturated at regular intervals for 3 days. On the exposed concretes with smooth and bright surfaces base coating process should be done together with the exposed concrete primer and after the base coating is dried the plastering application should be made.


APPLICATION FEATURESThe wall is made ready to paint by applying finishing putty on the Fixtek plaster. Therefore, it is used instead of gypsum plaster of the much higher cost. It provides fine plaster function in single later applications. It creates a solid foundation with its high adhesive and tensile strength. It is resistant to moisture for interiors and exteriors and allows the places to breathe. By means of this feature it has a supe-rior advantage compared to gypsum plaster. It is moisture and water resistant for exteriors.

IMPLEMENTATIONFixtek plaster is mixed with the help of mixer (8,5-9,5 lt. water and 40 kg mortar) and applied with the help of a trowel or plaster machine by spraying on the wall. For a proper plaster application, special aluminum profiles should be used. Corner pro-files should be used to prevent breakages in corners. The cement-based hand plas-ter applied as horizontal bands should be leveled with the special aluminum leveling profiles. When the plaster is sufficiently hardened (when pressed with a finger the plaster should not be caved) surface is come threadbare. The surface is finished with the help of a damp sponge. Application thickness for one layer should be between 1 cm and 2,5 cm. If the thickness is greater than 2,5 cm, the second layer should be applied at the thickness of maximum 2-2,5 cm after the first layer has set. The time required to wait between coating applications is 24 hours.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. In terms of durability of the product the surface should be dam-pened at regular distances within 7 days after the application. Plaster mesh is re-commended in joints of different materials and on the points where movement can appear. For the applications to be made on the Fixtek plaster, you should wait at le-ast 15 days depending on the ambient temperature. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTION14 kg/m2 (for thickness of 1 cm)




Water Mixing Ratio 8,5-9,5 lt. water / 40 kg. powder Application Temperature Between +5 °C and 35 °C Adherence Strength > 0,1 N/mm2



Thermal Conductivity 0,400 (W/mK - 23 °C) Skinning Time < 60 dk. 20 °C Shelf Life 8 months in dry conditions

66

SATIN PUTTY

DESCRIPTIONIt is a cement-based putty with high-adhesive feature, providing a long working time for the master, being able to be sandpapered, used for achieving a ready-smo-oth last layer surface in exteriors, interiors, concrete surfaces and being threadbare surface.

APPLICATION FIELDSIt is used for achieving a smooth last layer surfaces that is ready for painting in in-terior and exterior, concrete surfaces, being threadbare surfaces, gypsum plasters and plasterboard surfaces. It is available in white and gray colors.

SURFACE PREPARATIONThe application surface must be firm and clean. The materials that prevent adhe-rence such as paint, dust, etc. should be removed from the surface. The required repairs on old grounds should be made with Fixkim repair mortars. The surface must be dampened with water before the application.


IMPLEMENTATION20 kg Fixkim Satin Putty shall be poured into 7-8 liter clean water and mixed with a low-speed mixer until getting a lump-free homogenous mixture. The mortar shall be allowed to stand for 5 minutes and mixed again for 1 minute. Application thickness should be 2-3 mm. For the thicker applications the second layer shall be applied when the first layer is drawn. In order to achieve smooth surface fine sandpaper can be applied. Fixkim exposed concrete lining is applied on the exposed concretes. Putty application can be made after 20 minutes.


CONSUMPTION1,2 kg/m2 for thickness of 1 mm.



TECHNICAL SPECIFICATIONSAppearance Gray-colored fine powderPowder Density 1,200 ± 100 kg/ltWater Mixing Ratio 7-8 lt. water / 20 kg. powderPot Life Max. 2 hoursUnit Weight in wet 1500 ± 200 kg / m3

Bending Strength > 3 N/mm2 (28 days)Adherence Strength > 0,3 N/mm2 (28 days)Compressive Strength > 10 N/mm2 (28 days)

67

POWDER PRIMER

DESCRIPTIONIt is a cement-based, polymer blended, high quality laying plaster that forms reliable surfaces.

APPLICATION FIELDSIt is used for the surfaces such as exposed concrete, concrete ceiling, aerated con-crete, pumice concrete, etc. in order to resolve the adherence problems resulting from the surface before all kinds of cement based plaster applications.

SURFACE PREPARATIONThe materials that prevent adherence such as mold oil, dust, paint, dirt should be removed from the surface. The cracks and holes should be covered with Fixkim re-pair mortars. The surface must be dampened before application. On the exposed concretes with smooth and bright surfaces base coating process should be done together with the exposed concrete primer.


IMPLEMENTATIONFirstly, 8-9 liters of water should be added into the container in which the mixture will be made. Then, 40 kg of powder primer should be poured into the water. It is recommended that mixing should be made with a low speed mixer or a trowel. The surface should be dampened in the morning and evening for at least 3 days after the application. After that the other plaster should be applied to the surface.


CONSUMPTIONAbout 4-5 kg/m2 with trowel and approximately 3-4 kg/m2 with trolien.


HEALTH AND SAFETYAvoid contact with skin and eyes. Gloves must be worn during packaging and ap-plication.

TECHNICAL SPECIFICATIONSAppearance Gray-colored powderPowder Density 1600 ± 100 kg/ m3

Water Mixing Ratio 8 - 9 lt. water / 40 kg. powderApplication Temperature Between +5 oC and 35 oCAdherence Strength > 0,1 N/mm2

Skinning Time < 60 dk. 20 °CCompressive Strength > 11 N/mm2 Bending Strength > 4 N/mm2 Shelf Life 8 months in dry conditions

68

RESTORATION PLASTER

DESCRIPTIONIt is a restoration mortar ready for use in the restoration of historic buildings.

APPLICATION FIELDSIt is used for the plaster applications for the restoration of historic buildings inter-nally and externally.

SURFACE PREPARATIONThe surfaces should be purged from the powder materials such as mold oil, paint, dust, etc. Low adherence, moving parts should be removed from the surface. Before the application the surface should be dampened.


APPLICATION FEATURESIt is used as thin and thick plaster masonry mortar with the intended use depending on the design for interior and exterior in the historic buildings and castles and used as cast mortar in joint gaps. It does not damage the surface texture. Its design and application alternatives are available in 4 different types as Restoral Repair Mortar, Restoral Masonry Mortar, Restoral Fine Plaster and Restoral Thick Plaster depend-ing on the building structure and requirements. It is compatible with vulnerable and weak surfaces. It can be designed depending on the application.

IMPLEMENTATION25 Kg Fixkim Restoration mortar should be added to the mixing bowl with ap-propriate powder amount (Varies depending on the application purpose and consistency) and the mortar is mixed with low speed hand mixer until it forms a homogenous consistency. Then, the mortar should be waited for 5 minutes and it is ready after 1 minute mixing. It is applied between the thickness of 5 and 20 mm. It is applied in 10 mm according to the masonry mortar and applied between 4-6 mm according to the thin plaster design.


CONSUMPTIONConsumption: 13 to 17 kg / m2, for a thickness of 1 cm (varies according to the design.)



TECHNICAL SPECIFICATIONS Powder Density 1200-2000 ± 150 Kg / m3

Unit Weight in Wet 1500-2000 ± 100 Kg. / m3

Adherence Strength > 0.1 N / mm2 (varies according to the design.) Bending Strength > 2 N / mm2 (varies according to the design.) Compressive Strength > 6 N / mm2(varies according to the design.) Shelf Life 8 months in dry conditions

69

SELF-SPRAWLING FINE LEVELLING SCREED (3-7 MM)

SELF-SPRAWLING THICK LEVELLING SCREED (7-15 MM)

QUICK SETTING AND SELF-SPRAWLING LEVELLING SCREED (3-7 MM)

NORMAL SCREED

LIGHT SCREED

GROUND APPLICATION

MORTARS

72

DESCRIPTIONIt is cement-based, polymer blended, highly fluid self-sprawling surface leveling screed that can be applied at the thickness of 3-7 mm.

APPLICATION FIELDSIt is used as final layer of coating in internal floors of all buildings subject to medium and heavy pedestrian traffic and in the places where wanted to be constituted a proper ground for leveling before the applications of ceramic, laminate flooring and pvc coating. It is also used for repairing and correcting the damaged floors in old and new buildings. It provides a smooth surface by covering the subfloor gaps and roughness.

SURFACE PREPARATIONThe surface must be clean, dry and firm. Paint, plaster, concrete and any adhesive residues must be removing by scraping. The surface should be purged from dust by sweeping. If any, regional disorders should be repaired with Fixkim Repair Mortar. The surface should be dampened 1 day before the application. The saturated surface should be primed with Transparent Floor Primer. The surface must be primed 2nd time with transparent primer without diluting at least 60 minutes prior to applica-tion of surface leveling screed.


APPLICATION FEATURESIt should be applied in the thickness of 3-7 mm. It is easy and quick to apply. It is leveled by self-sprawling, eliminates the roughness of the subfloor. It can be applied on old concrete floors. It is economical.

IMPLEMENTATION25 kg Superficial Ground Leveling Screed is poured into average 6 liters of clean water and should be mixed with the help of a low speed hand mixer until getting homogenous consistency. The mortar shall be allowed to stand for 5 minutes and should be mixed again for 1-2 minutes. The prepared mortar is poured into the gro-und and should be leveled for filling the roughness on the surface. The leveling screed is self-sprawled. The thickness is adjusted with the help of a trowel. Gas extraction is achieved by scanning with a spiked roller. Roughness is required in very smooth surfaces.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. The surface should be dampened at regular intervals for 7 days after the application in terms of durability of the product (If curing liquid was not used). Do not violate the conditions for the specified application surfaces and ins-tructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.

CONSUMPTION1.3 to 1.5 kg / m2 (for thickness of 1 mm)


TECHNICAL SPECIFICATIONS Appearance A gray-colored fine powder Powder Density 1.40 ± 100 kg / lt. Water Mixing Ratio 25 kg. bag / 6 lt. water Application Temperature Between +5 °C and 35 °C. Liquidity Period 10-15 minutes Tensile Strength > 1 N / mm2 (28 days) Compressive Strength > 20 N / mm2 (28 days) Dry to touch 3 hours at 20 °C Opening to pedestrian traffic 24 hours at 20 °C Shelf Life 6 months in dry conditions Abrasion Resistance 5 cm2 / 50 cm2 by Böhme Method

SELF-SPRAWLING FINE LEVELLING SCREED (3-7 MM)

73







WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. The surface should be dampened at regular intervals for 7 days after the application in terms of durability of the product (If curing liquid was not used). Do not violate the conditions for the specified application surfaces and ins-tructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The packaged products should not be stored in humid conditions.CONSUMPTION1.6 to 1.7 kg / m2 (for thickness of 1 mm)


TECHNICAL SPECIFICATIONS Appearance A gray-colored fine powder Powder Density 1.60 ± 100 kg / lt. Water Mixing Ratio 25 kg. bag / 6 lt. water Application Temperature Between +5 °C and 35 °C. Liquidity Period 10-15 minutes Tensile Strength > 1 N / mm2 (28 days) Compressive Strength > 20 N / mm2 (28 days) Dry to touch 3 hours at 20 °C Opening to pedestrian traffic 24 hours at 20 °C Shelf Life 6 months in dry conditions Abrasion Resistance 5 cm2 / 50 cm2 by Böhme Method

SELF-SPRAWLING THICK LEVELLING SCREED (7-15 MM)

74








CONSUMPTION1.3 to 1.5 kg / m2 (for thickness of 1 mm)


TECHNICAL SPECIFICATIONS Appearance A gray-colored fine powder Powder Density 1.40 ± 100 kg / lt. Water Mixing Ratio 25 kg. bag / 6 lt. water Application Temperature Between +5 °C and 35 °C. Liquidity Period 10 minutes Tensile Strength > 2 N / mm2 (28 days) Compressive Strength > 40 N / mm2 (28 days) Dry to touch 1 hours at 20 °C Opening to pedestrian traffic 12 hours at 20 °C Shelf Life 6 months in dry conditions Abrasion Resistance (by Capon Method) ≤ 57 mm3 (in 100 rotations)

QUICK SETTING AND SELF-SPRAWLING LEVELLING

SCREED (3-7 MM)

75

DESCRIPTIONIt is cement-based high compressive strength ground mortar which is manufactu-red with high-quality graded sand, applied by hand and can be pumped by machine..

APPLICATION FIELDSIt is used as final layer of coating in internal floors of all buildings subject to medium and heavy pedestrian traffic and in the places where wanted to be constituted a proper ground before the applications of ceramic, laminate flooring and pvc coating.

SURFACE PREPARATIONThe surface must be clean, dry and firm. Paint, plaster, concrete and any adhesive residues must be removing by scraping. The surface should be purged from dust by sweeping. If any, regional disorders should be repaired with Fixkim Repair Mortar. The surface should be dampened 1 day before the application. The saturated surface should be primed with Transparent Floor Primer (In old concrete surfaces).


APPLICATION FEATURESIt should be applied in the thickness of 2-5 cm. It is easy and quick to apply. It can be applied on old concrete floors. It is economical.

IMPLEMENTATION40 kg Superficial Ground Screed is poured into average 4,5-6 liters of clean water and should be mixed with the help of a low speed hand mixer until getting homoge-nous consistency. The mortar shall be allowed to stand for 5 minutes and should be mixed again for 1-2 minutes. Cracks and holes on the surface should be covered with the Fixkim repair mortars. If the ground is an absorbent, application should be made after moisturizing the ground. The screed should be laid on the surface at the thick-ness of 2-5 cm by the screed machine by hand. When the surface is set corrections are should be made by mechanical polishing.


CONSUMPTION16 to 18 kg / m2 (for thickness of 1 mm)


TECHNICAL SPECIFICATIONS Appearance A gray-colored fine powder Powder Density 1600 ± 100 kg/m3

Water Mixing Ratio 40 kg. bag / 4,5-6 lt. water Application Temperature Between +5 °C and 35 °C. Particle size distribution 0 – 3 mm Bending Strength > 2 N / mm2 (28 days) Compressive Strength > 20 N / mm2 (28 days) Opening to pedestrian traffic 24 hours at 20 °C Shelf Life 6 months in dry conditions

NORMAL SCREED

76

DESCRIPTIONIt is cement-based high compressive strength ground mortar which is manufactu-red with high-quality graded sand and perlite, preventing the heat and sound trans-fer partly, not putting too much stress on the building, applied by hand and can be pumped by machine.

APPLICATION FIELDSIt is used as final layer of coating in internal floors of all buildings subject to medium and heavy pedestrian traffic and in the places where wanted to be constituted a proper ground before the applications of ceramic, laminate flooring and pvc coating.

SURFACE PREPARATIONThe surface must be clean, dry and firm. Paint, plaster, concrete and any adhesive residues must be removing by scraping. The surface should be purged from dust by sweeping. If any, regional disorders should be repaired with Fixkim Repair Mortar. The surface should be dampened 1 day before the application. The saturated surface should be primed with Transparent Floor Primer (In old concrete surfaces).


APPLICATION FEATURESIt should be applied in the thickness of 2-5 cm. It is easy and quick to apply. It can be applied on old concrete floors. It is economical.

IMPLEMENTATION40 kg Superficial Light Screed is poured into average 5-6,5 liters of clean water and should be mixed with the help of a low speed hand mixer until getting homogenous consistency. The mortar shall be allowed to stand for 5 minutes and should be mixed again for 1-2 minutes. Cracks and holes on the surface should be covered with the Fixkim repair mortars. If the ground is an absorbent, application should be made after moisturizing the ground. The screed should be laid on the surface at the thick-ness of 2-5 cm by the screed machine by hand. When the surface is set corrections are should be made by mechanical polishing.


CONSUMPTION13 to 14 kg / m2 (for thickness of 1 mm)


TECHNICAL SPECIFICATIONS Appearance A gray-colored fine powder Powder Density 1350 ± 100 kg/m3

Water Mixing Ratio 40 kg. bag / 5-6,5 lt. water Application Temperature Between +5 °C and 35 °C. Particle size distribution 0 – 3 mm Bending Strength > 1 N / mm2 (28 days) Compressive Strength > 7 N / mm2 (28 days) Opening to pedestrian traffic 24 hours at 20 °C Shelf Life 6 months in dry conditions

LIGHT SCREED

GROUND SURFACE HARDENERS

BASALT AGGREGATED SURFACE HARDENERS

SILICA AGGREGATE SURFACE HARDENERS

QUARTZ AGGREGATED SURFACE HARDENERS

CORUNDUM AGGREGATED SURFACE HARDENERS

80

DESCRIPTIONIt is a surface hardener applied to fresh concrete surfaces and consisting of cement, hard basalt aggregates, chemical additives, special coloring pigment and polymer additives.

APPLICATION AREASIt is applied indoors and outdoors where the wear resistance is required on the sur-face under heavy loads of traffic density. It is also used in industrial areas such as plants, materials warehouses, workshops; in shopping malls exhibition areas, sub-way stations, sidewalks and pedestrian paths where having the dense of human traffic; and in garage, parking, loading/unloading areas, petrol stations, aircraft hangars and helicopter runways.

SURFACE PREPARATIONAfter the base concrete has been poured into the floor as the formed concrete it should be leveled. When the base concrete is set so that the footprint is left, disc polishing is made. If the application will be made on the old concrete, at least 10 cm of C 25 concrete should be poured first. In order to increase the adherence between the new concrete and the old concrete and to ensure a good adhesion, ground pri-mer should be applied.


APPLICATION FEATURESIn order to ensure that the surface does not lose the water quickly than desired Fixkim Cure materials should be applied. The cure material provides the concrete to reach higher strengths, to restrain the formation of shrinkage cracks and surface chalking by preventing dehydration. In the cases that the cure materials are not applied, water should be sprayed lightly and the surface should be covered with foil or curing blanket.

IMPLEMENTATIONYou should wait until the carrying concrete is set as the footprint will be formed in the depth of 3mm when you come on it. Depending on the width of the concrete forms and consumption amount, surface hardener bags should be put by the edges of the concrete forms. 2/3 of the hardener which will be applied on the entire sur-face should be distributed via scattering method. The material should not be left on the surface in short bursts, but it should be distributed homogenously as much as possible. In addition, to prevent the segregation of the aggregates included in the product, it should not be spread to the farther afield. This operation may be done manually or special spreader equipment. The surface of the application should be wet as much as the surface hardener can take the moisture required. In the si-tuations that the concrete surface has much moisture than required, the surface hardener will be disappeared within the fresh concrete and lose effectiveness. If the surface is dry more that it is required, the product cannot take the dehydration water and cannot reach the required strengths. The surface hardener which has been scattered in homogenous manner and changed its color by taking the water will be absorbed into the concrete by disc polishing. The remained 1/3 amount of the hardener shall be sprinkled to the concrete surface and polished with the disk polishing. Then, the blade polishing is passed and the transaction is resumed until the desired polishing is obtained.


CONSUMPTION6 to 8 kg / m2



TECHNICAL SPECIFICATIONS Appearance Gray, red, yellow, green colored fine powder Powder Density 1600 ± 100 kg / m3

Impact Resistance (LA) Weight loss of 30-40% Application Temperature Between +5 ° C and 35 ° C. Abrasion Resistance 5 cm3 / 50 cm2 by the Böhme method Hardness 5 Mohs. Compressive Strength > 55 N / mm2

Bending Strength > 8 N / mm2

Shelf Life 8 months in dry conditions

BASALT AGGREGATED SURFACE HARDENERS

81

DESCRIPTIONIt is a surface hardener applied to fresh concrete surfaces and consisting of cement, hard silica aggregates, chemical additives, special coloring pigment and polymer ad-ditives.














SILICA AGGREGATED SURFACE HARDENERS

82

DESCRIPTIONIt is a surface hardener applied to fresh concrete surfaces and consisting of cement, hard quartz aggregates, chemical additives, special coloring pigment and polymer additives.














QUARTZ AGGREGATED SURFACE HARDENERS

83

DESCRIPTIONIt is a surface hardener applied to fresh concrete surfaces and consisting of cement, hard corundum aggregates, chemical additives, special coloring pigment and poly-mer additives.














CORUNDUM AGGREGATED SURFACE HARDENERS

WATERPROOFING MORTARS

CRYSTALIZED WATERPROOFING MORTAR

SINGLE COMPONENT WATERPROOFING MORTAR

FLEXIBLE TWO COMPONENT WATERPROOFING MATERIAL

SUPER FLEXIBLE TWO COMPONENT WATERPROOFING MATERIAL (LIQUID MEMBRANE)

FIXWATERSTOP

TWO COMPONENT SELF- SPRAWLING WATER-REPELLENT LEVELLING SCREED

CRYSTALIZED WATERPROOFING

MORTAR

DESCRIPTIONIt is cement-based, single component, crystalline waterproofing mortar that is re-sistant to the positive and negative water pressure and can be transferred to the capillary gaps of the cement based surfaces.

APPLICATION AREASIt is used in interiors and exteriors of all buildings as insulation material against the ground moisture, leaking water, positive and negative water pressure especially on retaining walls and wet volume of surfaces such as main and basement walls, terraces, swimming pools, water tanks, balconies, bathroom, toilet and kitchen. It prevents water leaks at the joints of concrete pipes and irrigation channels.

SURFACE PREPARATIONForeign substances such as dirt, oil, paint should be removed from the entire sur-face. The significant defects and holes should be repaired with Artmix RP3 Repair Mortar at least 24 hours prior to the application of waterproofing. Porous surfaces such as exposed concrete, cement based plaster and screed should be wetted with clean water and saturated.


APPLICATION FEATURESWhen the product is applied to the concrete surface, it penetrates into the concrete and the active chemicals react with the free lime and moisture in capillary gaps of the concrete and form insoluble crystalline structures.Application thickness: 2-3 mm, Applicable number of layers: 2-3 layers, Pot life: 30 minutesTime to wait between the layers: 6 hours, Time to wait for the application on the last layer: min. 7 days. Time to wait for the land fill: min. 7 days. The time needed to fill water tanks with water: min. 14 days

IMPLEMENTATION20 kg. Fixkim crystalline waterproofing mortar is poured into 8 liters of water for the application with a brush or into 5-6 liters of water for the application with trowel and mixed preferably with a low speed drill until no lump remain. In the application with brush waterproofing mortar is applied on the moistened surface with a brush perpendicular to each other in three layers. The second layer is applied when the first layer is hardened but not dried completely yet (within about 6 hours depending on the temperature). In the application with trowel, the first layer waterproofing mortar is applied as a plaster layer in 5-10 mm on the old concrete, brick wall or bri-quette surfaces. The second layer is applied over it in the consistency of syrup. In the dry scattering application crystalline waterproofing mortar is applied by sprinkled to the joint gap on the horizontal surfaces in the form of powder. Regardless of the method among these 3 methods, curing with water after application is extremely important. After the application, the crystalline waterproof mortar should be pre-vented to dry immediately and must be kept damp about 1 week. For this, spraying water is useful as being in normal concrete curing application.WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood surfaces, metal surfaces and the surfaces exposed to the moisture. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The pac-kaged products should not be stored in humid conditions.

CONSUMPTIONWith a brush: 2 kg / m2 (in 3 layers), with trowel; 1,5 kg / m2 (for the thickness of 1 mm), by dry scattering; 2 kg / m2 (varies depending on the joint width)



TECHNICAL SPECIFICATIONS Appearance A gray-colored fine powder Powder Density 1400 ± 100 kg./m3

Dust / Water Mixing Ratio 20 kg / 8 lt (Brush) - 20 kg / 5-6 lt (Trowel) Bonding Strength ≥ 0,60 N /mm2

Capillary Water Absorption ≤ 0,15 gr (after 4 hours) Application Temperature Between +5°C and 35°C Commissioning Time Mechanical Durability: 3 days Waterproofing 7 days Pressure Water Resistant (DIN 1048) 5 bar positive Coating Time 3 days Shelf Life 6 months in dry condition

86

SINGLE COMPONENTWATERPROOFING

MORTAR

DESCRIPTIONIt is cement-based, single component, waterproofing mortar that can be applied against the positive and negative water pressure.

APPLICATION AREASIt is used in interiors and exteriors of all buildings as insulation material against the ground moisture, leaking water, positive and negative water pressure especially on retaining walls and wet volume of surfaces such as main and basement walls, terra-ces, balconies, bathroom, toilet and kitchen. It prevents water leaks at the joints of concrete pipes and irrigation channels.

SURFACE PREPARATIONForeign substances such as dirt, oil, paint should be removed from the entire sur-face. The significant defects and holes should be repaired with Artmix RP3 Repair Mortar at least 24 hours prior to the application of waterproofing. Porous surfaces such as exposed concrete, cement based plaster and screed should be wetted with clean water and saturated.


APPLICATION FEATURESMechanical endurance gaining time: 3 daysThe becoming the waterproofing: 7 daysPot Life: 30-45 minutesTime to wait between the layers: 4 hours

IMPLEMENTATION20 kg. Fixkim Silicone Waterproofing Mortar is poured into 8 liters of water for the application with a brush or into 5-6 liters of water for the application with trowel and mixed preferably with a low speed mixer until it will become a homogenous con-sistency. The surface must be dampened absolutely before the application. After the mixture is allowed to stand for 2 minutes it should be mixed again prior to appli-cation. It should be applied on the surface in 3 layers by using a brush or trowel. Each of the layers must be applied in the perpendicular direction to the previous one. You should wait at least 4 hours between the implementations of each layer. The second layer is applied when the first layer is hardened but not dried completely yet (within about 6 hours depending on the temperature). The specified periods of time is valid at the surface and ambient temperature of 20 oC; time increases at law temperatu-re and shortens at high temperature.

WARNINGSNo material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood surfaces, metal surfaces and the surfaces exposed to the moisture. Do not violate the conditions for the specified application surfaces and instructions for use. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is cement-based gloves should be worn during the application. The pac-kaged products should not be stored in humid conditions.

CONSUMPTIONWith a brush: 2 kg / m2 (in 3 layers), with trowel; 1,5 kg / m2 (for the thickness of 1 mm)



TECHNICAL SPECIFICATIONS Appearance A gray-colored fine powder Powder Density 1400 ± 100 kg./m Dust / Water Mixing Ratio 20 kg / 8 lt (Brush) - 20 kg / 5-6 lt (Trowel) Bonding Strength ≥ 0,80 N /mm2

Capillary Water Absorption ≤ 0,05 gr (after 4 hours) Application Temperature Between +5°C and 35°C Commissioning Time Mechanical Durability: 3 days Waterproofing 7 days Pressure Water Resistant (DIN 1048) 5 bar positive Coating Time 3 days Shelf Life 6 months in dry condition

87

FLEXIBLE TWO COMPONENT WATERPROOFING MATERIAL

DESCRIPTIONIt is cement and acrylic based, highly flexible, two-component, waterproofing mor-tar. In order to provide insulation, two components should be mixed.

APPLICATION AREASIt is used in concrete water tanks, swimming pools; base concrete shear walls aga-inst the pressurized and non-pressurized ground waters; and balconies, terraces; wet areas like bathroom and kitchen. It is resistant to the negative and positive water pressure in interiors and exteriors. It prevents the water leaks at the joints of the irritation channels and concrete pipes.

SURFACE PREPARATIONForeign substances such as dirt, oil, paint should be removed from the entire surfa-ce. The significant defects and holes should be repaired with Fixkim Repair Mortar at least 24 hours prior to the application of waterproofing. Porous surfaces such as exposed concrete, cement based plaster and screed should be wetted with clean water and saturated.


IMPLEMENTATIONFor each layer 20 kg powder component is poured slowly into 10 liters of liquid com-ponent and should be mixed with a low speed mixer until obtaining a homogenous consistency for approximately 2-3 minutes. After the mixture is allowed to stand for 2 minutes it should be mixed again prior to application. It should be applied in 3 layers by using a brush or trowel. Each of the layers must be applied in the perpendicular direction to the previous one. You should wait at least 5 hours between the imple-mentations of each layer. Potable water tanks should be disinfected with 5% sodium hypochlorite solution at least 7 days later than application and should be washed with potable water; then should be filled with the water. This process should be repeated at least 1 time in a year. The specified time periods are valid for the surface and ambient temperature of 20 oC; the period increases in low temperature and decreases in high temperature. For the surfaces to be walked on should be covered with a finish coat like screed, tile, etc. After the implementation flex tile adhesive for the ceramic coatings and flex granite adhesive for granite coatings should be used.


CONSUMPTION2 kg / m2 for the average thickness of 1 mm (Consumption for a single layer is 0,6 – 07 kg/m2)



TECHNICAL SPECIFICATIONS Appearance A powder component is gray-colored; B liquid component is white colored. Powder Density – Liquid Density 1400 ± 100 kg./m3 - 1 kg/lt. Mixing Ratio 20 kg powder -10 lt. liquid Application Temperature Between +5°C and 35°C Pot Life Max. 1 hour Bonding Strength ≥ 2,00 N /mm2

Capillary Water Absorption ≤ 0,10 gr (after 4 hours) Commissioning Time Mechanical Durability: 3 days, Water imperviousness: 7 days. Pressure Water Resistant (DIN 1048) 7 bar positive Coating Time 3 days Shelf Life 6 months in dry condition Time to wait between the layers Min. 5 hours

88

DESCRIPTIONIt is cement and acrylic based, highly flexible, two-component, waterproofing mor-tar. In order to provide insulation, two components should be mixed.

APPLICATION AREASIt is used in concrete water tanks, swimming pools; base concrete shear walls aga-inst the pressurized and non-pressurized ground waters; and balconies, terraces; wet areas like bathroom and kitchen. It is resistant to the negative and positive water pressure in interiors and exteriors. It prevents the water leaks at the joints of the irritation channels and concrete pipes.

SURFACE PREPARATIONForeign substances such as dirt, oil, paint should be removed from the entire surfa-ce. The significant defects and holes should be repaired with Fixkim Repair Mortar at least 24 hours prior to the application of waterproofing. Porous surfaces such as exposed concrete, cement based plaster and screed should be wetted with clean water and saturated.


IMPLEMENTATIONFor each layer 20 kg powder component is poured slowly into 8 liters of liquid com-ponent and should be mixed with a low speed mixer until obtaining a homogenous consistency for approximately 2-3 minutes. After the mixture is allowed to stand for 2 minutes it should be mixed again prior to application. It should be applied in 3 layers by using a brush or trowel.. Each of the layers must be applied in the perpendicular direction to the previous one. You should wait at least 5 hours between the imple-mentations of each layer. Potable water tanks should be disinfected with 5% sodium hypochlorite solution at least 7 days later than application and should be washed with potable water; then should be filled with the water. This process should be repeated at least 1 time in a year. The specified time periods are valid for the surface and ambient temperature of 20 oC; the period increases in low temperature and decreases in high temperature. For the surfaces to be walked on should be covered with a finish coat like screed, tile, etc. After the implementation flex tile adhesive for the ceramic coatings and flex granite adhesive for granite coatings should be used.


CONSUMPTIONAverage 1,8 kg / m2 (Consumption for a single layer is 0,6 kg/m3)


HEALTH AND SAFETYAvoid contact with skin and eyes. Gloves must be worn during packaging and app-lication. TECHNICAL SPECIFICATIONS

Appearance A powder component is white-colored; B liquid component is white colored. Powder Density – Liquid Density 1200 ± 100 kg./m3 - 1,05 kg/lt. Mixing Ratio 20 kg powder -8 lt. liquid Application Temperature Between +5°C and 35°C Pot Life Max. 1 hour Bonding Strength ≥ 2,50 N /mm2

Capillary Water Absorption ≤ 0,10 gr (after 4 hours) Commissioning Time Mechanical Durability: 3 days, Water imperviousness: 7 days. Pressure Water Resistant (DIN 1048) 8 bar positive Coating Time 3 days Shelf Life 6 months in dry condition Time to wait between the layers Min. 5 hours

89

SUPER FLEXIBLE TWO COMPONENT WATERPROOFING MATERIAL

(LIQUID MEMBRANE)

DESCRIPTIONIt is a polymer reinforced powder insulation material that includes special type ce-ment and chemicals, hardens in 2-3 minutes when reacts with water and provides high adherence; and used in insulation and repair of active water leaks.

APPLICATION AREASIt is used for cutting the water in very short time comes in the form of leakage or by pressure from the holes on the pipes and deep cracks in the foundations, basements, retaining walls, lift spaces, pools, water tanks and concrete pipes.

SURFACE PREPARATIONThe surface should be clean, smooth and firm. The residuals such as, dirt, oil, paint should be removed from the surface to be made implementation with a wire brush. The discharging hole should be opened in 3x3 cm sizes in order to decrease the water resistant. It should be noticed that the depth to width with ratio must be 2/1.


APPLICATION FEATURESPot Life of the mortar: 2-3 minutesSetting time: 4-5 minutes (varies depending on the temperature)

IMPLEMENTATIONPreparation of the Mortar: You should make available the water plugging mortar consumable in 2-3 minutes by mixing the water in a clean container. The water ratio should be 25% to 30% of the weight of powder mortar. Do not mix it more than 30 seconds. The prepared mixture should be at the consistency, please use the warm water in cold weather.

APPLICATION INFORMATIONThe hole in the application field is extended min. 3x3 cm in order to reduce the water pressure. The prepared mortar starts to heat up. When the mortar is warmed up sufficiently, you should whip it into the conical shape with your hand and plug the hole in one motion and apply force with your hand and press it about 2 minutes. Only after the water sealing mortar is hardened, pull your hand. For repairing the large holes which cannot be covered in one time, repeat this process several times by moving from the out of the hole to the center.


CONSUMPTIONApproximately 2 kg for 1 lt of the volume.


TECHNICAL SPECIFICATIONS Appearance Gray-colored fine powder Powder Density 1 kg/lt Water Mixing Ratio 25 kg powder mortar / 6,25 – 7,5 lt water Compressive Strength After 1 hour > 10.0 N/mm2 After 24 days > 22.0 N/mm2 After 28 days > 40.0 N/mm2 Application Temperature +5 ° C and 35 ° C. Shelf Life 6 months in dry condition Packaging 5 kg.

90

FIXWATERSTOP

DESCRIPTIONIt is two-components, very strong water-repellent leveling screed which is consists of a cement based, polymer blended, powder mortar of A component and acrylic emulsion of B component.

APPLICATION AREASFixkim two-component water-repellent leveling screed is used in horizontal conc-rete roof surface and flat surfaces where water impermeability is desired.

SURFACE PREPARATIONDust, oil, paint and other chemicals and lose parts should be removed from the app-lication surface. The defects on the surface should be repaired with Fixkim Repair Mortar at least 24 hours prior to the application. All mineral based, absorbent sur-faces should be wetted before the application and must be kept moist. In the cases where the surface porosity is high, application should be made after the application of 2 layers of Fixkim Liquid Primer on the surface.

APPLICATION CONDITIONSIt should be considered that the ambient temperature is between +5 oC to +35 oC and the surface temperature is between 10 °C and +30 °C during the application. It should not be applied for the frozen, melting surfaces or the surfaces that is at the risk of frost within 24 hours. It should not be applied under direct sunlight and strong wind.

IMPLEMENTATIONApplication should be made after the application of Fixkim Liquid Primer in 2 layers. A component (Powder) is poured slowly into container with B component (liquid) and should be mixed with a low speed mixer until obtaining a homogenous lump-free mixture. Extra water should not be added into mortar. The mixture is allowed to stand for 5 minutes and mixed again. After the mortar is poured into the ground, it is sprawled with a triangular notched steel trowel in order to assure easy leveling. Without time wasting, gas extraction is achieved by scanning with a spiked roller. Fixkim two-component water-repellent leveling screed is applied as two layers. Application of the second layer is made after 24 hours at +20 oC. The mixture in the pot should be consumed in 20 minutes.


CONSUMPTION1,5 kg / m2 for the thickness of 1 mm



TECHNICAL SPECIFICATIONS Appearance A powder component is white-colored; B liquid component is white colored. Powder Density – Liquid Density 1450 ± 100 kg./m3 - 1 kg/lt. Mixing Ratio 25 kg powder -8 kg. liquid Application Temperature Between +5°C and 35°C Pot Life 20 minutes Walking time on it After 48 hours at +20°C Compressive Strength > 20 N / mm2 (10 days) Adhesion Strength > 0.8 N / mm2 (10 days) Consumption amount 2.5 mm 4,250 kg/m2

Time to wait between the layers 24 hours at +20 oC Shelf Life 8 months in dry condition Bending Strength > 3 N / mm2 (10 days)

91

TWO COMPONENTSSELF-SPRAWLING

WATER-REPELLENTLEVELLING SCREED

PU 160 LIQUID MEMBRANE

PU 250 WATERPROOF COATING

LIQUID MEMBRANE

BT 2K

BT 1K

WATERPROOFING SYSTEMS

PU 160 LIQUID MEMBRANE

DESCRIPTIONIt is polyurethane-based, two-component, self-sprawling membrane.

APPLICATION AREASIt can be used;- On the roofs and terraces of the buildings, on the slope screed reinforced and with the thermal insulation,- For the insulations of under tile surfaces which constitute all kinds of volume in swimming pools, balcony and bathroom,- In the basements, water tanks and irrigation channels,- Gypsum and cement board panels,- As grout,as a membrane for waterproofing insulation. It is solvent-free, has high mechanical and chemical resistance, high tensile and tear strength.

SURFACE PREPARATIONPrior to the application of primer coating, oils, dirt, dust and greases should be re-moved from the surface to be applied. The free particles on the surface, cement slurry and the particles preventing the adhesion on the surface should be cleaned. The surfaces where primer application has been finished should be blunt with the quartz sand depending on the condition of the surface; and this will positively affect the performance of the surface where PU 160 membrane will be applied. In the un-der tile PU 160 applications, blunting the vertical and horizontal product with quarts sand will connect the product to the ceramic surface.

PREPARATION OF THE MIXTURE A and B components should be mixed with a low speed mixer at least 3-4 minutes by paying attention to the mixture ration until obtaining a homogenous mixture. It will be ready to use after mixing.

COATING SYSTEMIn the event of over 24 hours of priming process, the ground is roughened with emery PU 160 should be applied. The product should be spread on the ground with the help of a notched trowel in order to achieve the desired thickness on the surface of the ground and must be deflated with a spiked roll when it comes to proper consistency. In the cases that high UV resistance is desired it is recommended to apply 0.150 – 0.200 kg PU 130 or PU 135 protective coating per square meter.

The products recommended for use under this product:- SC 210 Multi-Purpose Epoxy Primer- SC 215 Solvent-Free Epoxy Primer- SC 220 Epoxy Primer for 100% Wet Surfaces- SC 270 Impregnation Primer with Low Viscosity of Epoxy Adhesion Bridge

The products recommended for use on this product:- PU 130 Polyurethane Flat Protective Paint- PU 135 Polyurethane Gloss Protective Coating

APPLICATION CONDITIONSIf the application ambient temperature is under +10 oC or +30 oC, the application should not be done.- It should not be applied in rainy and windy weather conditions.- The coating should be protected from water contact at least 24 hours after the completion of the coating.- During the application thinning products should not be added into the product.- The relative humidity should not exceed 80% during application.

SAFETY The product is for professional use. Please note the safety instructions on the package before using, if necessary, see the Material Safety Data Sheet. Do not inhale, avoid contact with skin and eyes, do not ingest, use the appropriate safety equipment. Take the necessary measures to prevent pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas.

HANDLING AND STORAGE- The product should be stored at the temperature between 5 to 35 oC.- The product should not be exposed to direct sunlight.- The opened product should be kept in its package by sealed cover; if the packaging of the product is opened, it should be consumed within maximum one week.

NOTEFİXKİM reserves the right to make improvement/revision in the product and in this technical document in time. This Technical Data Sheet invalidates the Technical Data Sheet previously published for this product and valid for 5 years. The user should make sure that the technical document in his hand is the most current version, if necessary, he should questioned the timeliness of the document from the company. Whether the product is being used for the purpose of the product or not, and the validity of the application conditions and formations are under the responsibility of the practitioner. FİXKİM Epoxy Paint does not accept any guarantee requests regarding the results, work accidents, direct or indirect loss or damages arising from the application of the products as being recommended. The packaging values specified above the nominal values in the formulations standardized by FİXKİM. Under the normal production con-ditions, slight deviations prescribed in the international standards may occur.

TECHNICAL SPECIFICATIONSColor White-gray (RAL colors)View MatColor changes may occur at the direct exposure to sunlight, but does not affect the perfor mance of the product.Thinner Polyurethane thinnerSolids by weight 100%Density 1.30 g/cm3

Consumption 0.80 to 1.60 kg / m2

Packaging 16 Kg of Component A + 4 Kg of component B; Total 20 KgFlash point > 25 ° CMixing Ratio 4/1Application Methods Brush, roller, trowelPot Life 30 min / 25 ° CShelf Life 1 yearWaiting time between coats 25 ° C for 12 hoursDrying Time 25 ° C for 24 hoursMechanical Strength 7 daysElasticity 200%Shore D Hardness (7 days / 25 ° C) 45Equipment Cleaning Polyurethane Thinner

94

16 4

SAFETYThe product is for professional use. Please note the safety instructions on the pac-kage before using, if necessary, see the Material Safety Data Sheet. Do not inhale, avoid contact with skin and eyes, do not ingest, use the appropriate safety equip-ment. Take the necessary measures to prevent pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas.

HANDLING AND STORAGE- The product should be stored at the temperature between 5 to 35 oC.- The product should not be exposed to direct sunlight.- The opened product should be kept in its package by sealed cover; if the packaging of the product is opened, it should be consumed within maximum one week. A dried film may occur on the surfaces which were opened and re-sealed; it can be reused after removing the film layer on the surface.

NOTEFİXKİM reserves the right to make improvement/revision in the product and in this technical document in time. This Technical Data Sheet invalidates the Technical Data Sheet previously published for this product and valid for 5 years. The user should make sure that the technical document in his hand is the most current version, if necessary, he should questioned the timeliness of the document from the company. Whether the product is being used for the purpose of the product or not, and the validity of the application conditions and formations are under the responsibility of the practitioner. FIXKIM Epoxy Paint does not accept any guarantee requests re-garding the results, work accidents, direct or indirect loss or damages arising from the application of the products as being recommended. The packaging values spe-cified above the nominal values in the formulations standardized by FIXKIM. Under the normal production conditions, slight deviations prescribed in the international standards may occur.

TECHNICAL SPECIFICATIONS Color Clear-White (RAL) View Mat Solids by weight 70% Clear - 75% white and RAL colors Density 1.10 gr / cm3 Transparent - 1.20 gr / cm3, white and RAL colors Consumption Variable according to the state of the surface. Application Methods Brush, Roller, Airless Spray Gun Shelf Life 6 month Tensile Strength 9 N / mm2

Elasticity 400% Shore D Hardness (7 days / 25 ° C) 45 Equipment Cleaning Polyurethane Thinner

PU 250 WATERPROOF COATING

95

DESCRIPTIONIt is polyurethane-based, air-cured, single-component flexible waterproof coating with the low ratio of solvent.

APPLICATION AREASIt is used for waterproofing in balcony, roof and terraces; concrete asphalt and alkali stone surfaces, concrete wall of the base of the buildings, basements of the buildings, tunnels and underpasses, and all kinds of concrete structures. Its UV re-sistance is high and provides a high adherence to the applied surface, bridges the shrinkage cracks; it is resistant to the bacteria, alkali and sands in the soil when it is applied to the base concrete walls.

SURFACE PREPARATIONPrior to the application of primer coating, oils, dirt, dust and greases should be re-moved from the surface to be applied. The free particles on the surface, cement slurry and the particles preventing the adhesion on the surface should be cleaned.

APPLICATION METHODSIt should be considered that the temperature of the product before the application should be between +10°C and +30°C. The product should be mixed with a low speed mixer at least 3 minutes until obtaining a homogenous mixture. In order to comple-tion of the curing the surface where PU 250 has been applied, the relative humidity on the air must be between 40% and 70%. The surface should be avoided from the contact with rain at least 3 hours after the implementation.

APPLICATION CONDITIONS- If the application ambient temperature is under +5 oC or +30 oC, the application should not be done.- It should not be applied on the wet and damp surfaces.

LIQUID MEMBRANE

DESCRIPTIONIt is acrylic polymer resin and water based, single component, ready to use, flexible white colored (paintable) waterproofing material that can be easily applied to the floor of each ground.

APPLICATION AREASIt can be used in interior and exteriors, in horizontals and verticals, flat and pitc-hed roof, terraces, balconies, pools and water tanks, in runnels, eaves and edges of chimney; and the surfaces such as concrete, plaster, brick, zinc, galvanized steel .

PROPERTIES- It is ready to use.- Its implementation is very easy and has a semi-fluid property. Therefore it can cover easily very difficult surfaces. Labor costs are low.- It is flexible. It can extend 600%, after 24 hours at 23 C and in the thickness of 1 to 1.5 cm.- In ensures an excellent adhesion to all of the building materials. (Adhesion strength in mineral based surfaces: 5.15 kgf/cm2.- It prevents its elasticity in hot and cold differences. (476% at 70 oC; 397% at -17 oC)- Resistant to the weak chemicals.- Allows for inhalation on the surfaces. (Water vapor permeability isd 27.6 g/m2 day, after 24 hours at the temperature of 23 oC and humidity of 65%).-Tensile strength is 24.5 kgf/cm2 after 24 hours and 55 kgf/cm2 after 72 hours at 23°C - Solvent-free- Decorative. Standard production is white colored; it can be produced in various colors depending on the requested amount and can be colored by color tubes or can be painted with only water based paint with the same elasticity structure.

APPLICATIONLiquid membrane should be applied on the moisture-free, dry and clean surfaces. All kinds of oils, dirt, durst and lose floors that can prevent the product to adhere on the application surface should be removed. Plaster and concrete surfaces should be cleaned with mild water and soap prior to the application. The surfaces where applications will be made should have a slope (min 5%) not allowing to ponding. The gaps and holes on the surface should be filled with Fixkim repair mortar. Depending on the state of the surface, Liquid Membrane should be applied as one layer of primer by thinning with 100% of water and 2 layers should be applied without thinning on this layer. (Application should be made in mini-mum two layers) The second layer must be applied at 90o right direction to the first layer. Liquid Fiber Membrane should be applied in the form of strip at the vertical and horizontal joint points. Especially in dry weather conditions it should be applied between +5 oC and +35 oC. It should not be applied in rain, snow and frost weather conditions. The applied surfaces must be protected from weather conditions for at least 24 hours.

WARNINGIn order to achieve required performance and strength against the external influ-ences by the entire surface where Liquid Membrane has been applied, top of the surface should be protected with stem, ceramic or similar coatings. Application tools are cleaned with water. During the application, wearing flat-bottomed rubber shoes is recommended.

DRYING TIME (at 20 ° C, 65% HR)The first drying in 12 hoursSecond layer in 24 hours.Drying fully in 48 hours

CONSUMPTIONDepending on the applied surface, structure, smoothness and porosity; for each la-yer; 0,750-1 kk/m2 in vertical and 1-1.5 kg/m2 in horizontal. The consumption values given above are the approximate values and the final consumption will be deter-mined at the end of the work because of the differences depending on the surface structure.

STORAGEIt can be stored for 1 year in its original packaging as long as it has been stored in a cool, dry place by protecting from humidity, freezing and direct sunlight.

TECHNICAL SPECIFICATIONSShape Semi-LiquidColor WhiteDensity 1.30 ± 0.1 kg / lt.Elongation to break at least 600%Adhesion strength 12 kgf / cm2

96

DESCRIPTIONTwo-component, flexible, water-based, fiber reinforced, polymer bitumen waterp-roofing material.

APPLICATION AREASIn the underground applications such as base, curtain, wall and basement as water and damp-proofing material. For the protection and insulation of the structures and structural elements exposed to temporary and permanent water pressure and le-aking water. It also can be used as water insulation material in the dry and slightly damp details in terrace, roof, kitchen, bathroom, etc.; in insulation of the mineral surfaces such as concrete, stone, brick, briquette, plaster and screeds; for repairing the insulations like old bitumen membrane asphalt. It is used in bonding the Ther-mal Insulation materials together with the equipment such as Insulation mesh and isolation cloth; and in the insulation applications that should be resistant to higher pressured water.

SURFACE PREPARATIONThe application surface should be cleaned from dust, dirt, rust and grease; loose material should be scratched. Sharp edges and corners should be rounded. Iron and wooden wedges should be removed from the surface and if any, gaps should be fil-led. Bevels should be made in diameter of minimum 4 cm on the corners and edges. BT 2K should be applied on the dry concrete by after primer.

APPLICATION METHODMixingMixture amounts:24 kg liquid component8 kg powder component

Primer Application:Powder component is added slowly into liquid component and mixed with 400 to 600 rpm mixer for 3-5 minutes until obtaining a homogenous and smooth mixture; together with this primer 1, 2 or liquid component of BT 2K is mixed in the ratio of 1/10, and with water in the ratio of 1/5 and the mixture is thinned; then it can be used as primer. The material should be distributed in a balanced manner with an approp-riate brush and it should be applied without allowing the material accumulation on horizontal surfaces. The primer should be dried and then application should be done.

Coating ApplicationAfter the primer has dried, it should be applied with brush, trowel or appropriate spray equipment in the thickness of 2 to 5 cm. Depending on the absorption, rough-ness of the surface and water pressure exposed by the insulation layer, it can be applied more. If the application shall be made in 2 layers, you should wait for curing the first layer and the application of the other layer should be made later. For incre-asing the mechanical specifications in the horizontal and vertical junctures in large areas and for bridging the cracks, it should be used with 50-100 gr/ m2 of fiberglass or mesh. The prepared mixture should be consumed within 1-2 hours depending on the temperature.

SAFETYThe product is for professional use. Please note the safety instructions on the pac-kage before using, if necessary, see the Material Safety Data Sheet. Do not inhale, avoid contact with skin and eyes, do not ingest, use the appropriate safety equip-ment. Take the necessary measures to prevent pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas. HANDLING AND STORAGE- The product will freeze at the temperatures below 0 oC- The shelf life of the product in its original unopened packaging and in proper sto-rage conditions is 12 months.

NOTEFIXKIM reserves the right to make improvement/revision in the product and in this technical document in time. This Technical Data Sheet invalidates the Technical Data Sheet previously published for this product and valid for 5 years. The user should make sure that the technical document in his hand is the most current version, if necessary, he should questioned the timeliness of the document from the company. Whether the product is being used for the purpose of the product or not, and the validity of the application conditions and formations are under the responsibility of the practitioner. FIXKIM Epoxy Paint does not accept any guarantee requests re-garding the results, work accidents, direct or indirect loss or damages arising from the application of the products as being recommended. The packaging values spe-cified above the nominal values in the formulations standardized by FIXKIM. Under the normal production conditions, slight deviations prescribed in the international standards may occur.

TECHNICAL SPECIFICATIONS Color Black View Viscous liquid Thinner Water Solids by weight 35% Density 1.10 g / cm3

Mechanical Strength 7 days Equipment Cleaning Water with Pot Life 1-2 hours Shelf Life 1 year Flash point 100 C Mixing Ratio Liquid / Powder: 3/1

Consumption Insulation against humidity: for min. thickness of 3 mm, 3,3 kg / m2

Against non-pressurized water For min. thickness of 4 mm. 4.4 kg / m2

For pressurized water For min. thickness of 6 mm, 6,6 kg / m2

As a primer for bonding heat-insulating panels min.2 kg / m2

The use of liquid component by adding water in the ratio of 1:10 0.20 to 0.25 kg / m2

Use of the mixture mortar by adding water in the ratio of 1:5 0.5-0.8 kg / m2

The amount of consumption may vary depending on application detail and surface smoothness and porosity. Packaging 32 kg plastic bucket of liquid and powder components (Liquid: 24 kg, Dust: 8 kg) Application Methods Brush, Roller, Air Spray Gun, Airless Spray Gun Waiting time between coats The second coat should be applied after the first coat is completely cured. Drying Time Minimum 48 hours depending on the temperature and relative humidity Water resistance after curing (DIN 1048) of 7 bar

BT 2K

97

24 8

BT 1K

DESCRIPTIONWater-based, cold-applied bitumen emulsion waterproofing material.

APPLICATON AREASIt is used as damp-proofing material in the foundations and basements of the build-ings; as waterproofing material in dry or wet details in terrace, roof, kitchen, bath-room, etc.; as primer under the bitumen coatings; as lining material and binding in the applications of fiberglass, cross-stitch, etc.; in protection of metal surfaces such as steel construction, pipe, etc. as impermeability and adhesion promoter into the mortars and plasters created with cement and/or fine sand; to prevent the con-struction dies from degradation of water and as mould-release agent.

SURFACE PREPARATION- The application surface should be cleaned from grease, dust and dirt- Free particles on the surface, cement slurry on the concrete surfaces and the par-ticles preventing the adhesion should be cleaned.

METHOD OF APPLICATIONBefore the application of primer on the surfaces where the application shall be done, surface smoothness, surface dryness and cleanness and the existence of the slope screed should be checked. After establishing these conditions, Sliding Based Wa-terproofing Material BT1K Primer should be applied to the surface with a brush or spray gun in 400 gr per square meter and should be waited until it is dried com-pletely. Whenever it is necessary, it should be used by thinning with 20% of water. Depending on the weather conditions, it is dried in approximately 4 or 5 hours. In the applications of two layers, the second layer should not be applied before the first layer is dried fully. Membrane pasting job starts after the primer is completely dry.

BENEFITSSince it does not contain solvent, it is eco-friendly and can be used in closed areas; can be applied on dry and wet surfaces. After it has been dried, it creates a water and moisture resistant layer on the application surface. It is used as a primer under the bituminous coatings, insulation aimed coating, and as impermeability and adhe-sion promoter additive in cement based mortars.

SAFETYThe product is for professional use. Please note the safety instructions on the pack-age before using, if necessary, see the Material Safety Data Sheet. Do not inhale, avoid contact with skin and eyes, do not ingest, use the appropriate safety equip-ment. Take the necessary measures to prevent pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas. HANDLING AND STORAGE- The product will freeze at the temperatures below 0 oC- The shelf life of the product in its original unopened packaging and in proper stor-age conditions is 12 months.

NOTEFİXKİM reserves the right to make improvement/revision in the product and in this technical document in time. This Technical Data Sheet invalidates the Technical Data Sheet previously published for this product and valid for 5 years. The user should make sure that the technical document in his hand is the most current version, if necessary, he should questioned the timeliness of the document from the company. Whether the product is being used for the purpose of the product or not, and the validity of the application conditions and formations are under the responsibility of the practitioner. FİXKİM Epoxy Paint does not accept any guarantee requests re-garding the results, work accidents, direct or indirect loss or damages arising from the application of the products as being recommended. The packaging values speci-fied above the nominal values in the formulations standardized by FİXKİM. Under the normal production conditions, slight deviations prescribed in the international standards may occur.

TECHNICAL SPECIFICATIONS Color Dark Brown View Bright Thinner Water Solids by weight 35% Density 1.01 g / cm3

Consumption 400 gr/m2

Packaging 17 kg net plastic packaging Flash point Nonflammable Application Methods Brush, Roller, Air Spray Gun, Airless Spray Gun Shelf Life 1 year Waiting time between coats 4-5 hours / 25 oC Drying Time Can be walked on it 5 hours later at 25 oC Mechanical Strength 7 days Equipment Cleaning With water

98

15

PARAFFIN BASED CURE LIQUID

ACRYLIC RESIN BASED CURE LIQUID

SOLVENT BASED CURE LIQUID

CURE LIQUIDS

PARAFFIN BASED CURE LIQUID

102

DESCRIPTIONParaffin emulsion based, white colored, water based, liquid curing material that prevents quick water losses. It prevents the shrinkage cracks on the surface by preventing the evaporation of water within the concrete by means of the film layer created on the fresh concrete.

APPLICATION AREASThis product can be applied in all kinds of field concrete, channel and flume concretes and all of the surface curing applications. It is also used in industrial areas such as plants, material warehouses and workshops, etc; in the shopping malls, exhibition areas, subway stations, sidewalks and pedestrian paths, garage, parking, loading and unloading fields and petrol stations with dense human traffic. It must be used especially all kinds of weather conditions in high evaporation. It prevents the shrin-kage cracks and surface dusting.

SURFACE PREPARATIONIt is applied over the new concrete or on the top of the surface hardeners that was applied to fresh concrete by brush or roller. However, the concrete should be har-dened enough in order to avoid damaging the surface.


APPLICATION FEATURESImmediately after the outdoor applications, the surface should be protected against the effects like rain, snow, etc. for 2-3 hours. At the end of this period, the curing material is not affected by the external factors. Material must not be thinned de-finitely. It must not be applied to the wet surfaces. It should not be applied on non-porous, non-absorbent and glazed surfaces.

IMPLEMENTATIONIt should be applied by spraying, or a brush or a roller without accumulation on the surface immediately after removal of the molds in molded applications and no so-oner than the surface starts tom lose its first brightness (when the surface water starts to evaporate) on the fresh concrete. Soft and short bristled brush can be used on the wall and soft brush or roller can be used on the ground. The product should be applied on the surface as thin layer in equivalent thickness. After the app-lication, the surface will look semi-dull finish. Drying time of the material is about 2 hours. Specified periods of time are valid in at the surface and ambient temperature of 20 oC; the time increases in low temperature and decreases in high temperature.

CONSUMPTION200 – 250 gr/m2 (varies depending on the absorbency of the surface and weather conditions)


TECHNICAL SPECIFICATIONS Appearance White-colored liquid Looking after the application Semi-gloss, smooth, transparent film Liquid Density 1 kg / lt. Application Temperature Between +5 ° C and 35 ° C. Drying Time 45 minutes Flash Point +86 ° C Shelf Life 12 months in original packaging at temperature of +5 °C

ACRYLIC RESIN BASED CURE LIQUID

103

DESCRIPTIONAcrylic emulsion based, white colored, water based, liquid curing material that pre-vents quick water losses. It prevents the shrinkage cracks on the surface by preven-ting the evaporation of water within the concrete by means of the film layer created on the fresh concrete. It can be used to improve the performance of the old surface and to reduce the dusting.




APPLICATION FEATURESImmediately after the outdoor applications, the surface should be protected against the effects like rain, snow, etc. for 2-3 hours. At the end of this period, the curing material is not affected by the external factors. Material must not be thinned de-finitely. It must not be applied to the wet surfaces. It should not be applied on non-porous, non-absorbent and glazed surfaces.

IMPLEMENTATIONIt should be applied by spraying, or a brush or a roller without accumulation on the surface immediately after removal of the molds in molded applications and no so-oner than the surface starts tom lose its first brightness (when the surface water starts to evaporate) on the fresh concrete. Soft and short bristled brush can be used on the wall and soft brush or roller can be used on the ground. The product should be applied on the surface as thin layer in equivalent thickness. After the app-lication, the surface will look semi-dull finish. Drying time of the material is about 2 hours. Specified periods of time are valid in at the surface and ambient temperature of 20 oC; the time increases in low temperature and decreases in high temperature.



TECHNICAL SPECIFICATIONS Appearance White-colored liquid Looking after the application Semi-gloss, smooth, transparent film Liquid Density 1 kg / lt. Application Temperature Between +5 ° C and 35 ° C. Drying Time 2 hours Flash Point None Shelf Life 12 months in original packaging at temperature of +5 °C

SOLVENTBASED CURE LIQUID

104

DESCRIPTIONHydrocarbon resin based, transparent amber-colored, water based, liquid curing material that prevents quick water losses. It prevents the shrinkage cracks on the surface by preventing the evaporation of water within the concrete by means of the film layer created on the fresh concrete.




APPLICATION FEATURESIt contains solvent. Immediately after the outdoor applications, the surface should be protected against the effects like rain, snow, etc. for 2-3 hours. At the end of this period, the curing material is not affected by the external factors. Material must not be thinned definitely. It must not be applied to the wet surfaces. It should not be applied on non-porous, non-absorbent and glazed surfaces. During the implemen-tation, air circulation is necessary.

IMPLEMENTATIONIt should be applied by spraying, or a brush or a roller without accumulation on the surface immediately after removal of the molds in molded applications and no sooner than the surface starts tom lose its first brightness (when the surface water starts to evaporate) on the fresh concrete. Soft and short bristled brush can be used on the wall and soft brush or roller can be used on the ground. The product should be applied on the surface as thin layer in equivalent thickness. After the application, the surface will look semi-dull finish. Drying time of the material is about 40 minutes. Specified periods of time are valid in at the surface and ambient temperature of 20 oC; the time increases in low temperature and decreases in high temperature.



TECHNICAL SPECIFICATIONS Appearance Transparent, amber-colored liquid Looking after the application Semi-gloss, smooth, transparent film Liquid Density 0,80 kg / lt. Application Temperature Between +5 ° C and 35 ° C. Drying Time 40 minutes Flash Point +80 ° C Shelf Life 12 months in original packaging at temperature of +5 °C

LIQUID PRIMER

PRIMER 800 EXPOSED CONCRETE LINING

GENERAL PURPOSE ACRYLIC PRIMER

RAMMED ACRYLIC LINING

PRIMERS

DESCRIPTIONAcrylic emulsion based, colorless, non-saponifiable, water repellent and ready to use high adherence primer that is used in stabilization of dusty and highly absorbent grounds and has a very good binding property.

APPLICATION AREASIt is used for increasing the adherence on the old concrete before pouring the new concrete; ensuring the water and moisture impermeability especially in high absor-bance floors of the buildings and under the ground leveling screeds.

SURFACE PREPARATIONAnti-adhesion substances such as dust, oil, paint, silicone, curing agents, deter-gents, etc. should be removed from the application surface.


APPLICATION FEATURESComplete curing time is 6 to 8 hours (depending on the temperature).

TECHNICAL SPECIFICATIONS Appearance White-colored liquid Density 1.1 kg / lt Application Temperature Between +5 ° C and +35 ° C Full hardening time 6-8 hours. (Depending on temperature) Drying time 1-3 hours (depending on temperature) Second Floor Implementation Period 3-5 hours (depending on temperature) Shelf Life 1 year in original packaging

LIQUID PRIMER

108

IMPLEMENTATIONFixkim Floor Primer is poured on the ground without thinning and spread over the ground in equal amount by using a brush and applied in a single layer. Before the application of leveling screed, it must be applied in two layers certainly and must be allowed to be hardened. It significantly decreases the absorbency of the application surface. Drying time is prolonged in wet weather conditions. Specified periods of time are valid in at the surface and ambient temperature of 20 oC; the time increases in low temperature and decreases in high temperature.

CONSUMPTION150-200 gr/m2 (single layer)


PRIMER 800 EXPOSED CONCRETE LINING

104

DESCRIPTIONIt is acrylic based, single component plaster primer that increases the adherence of the surface and running time before applying the cement or gypsum based plasters for exposed concrete surfaces.

APPLICATION AREASIt is used as primer under the plaster on the surfaces of the exposed concretes with high porosity and permeability for increasing the adherence and reducing the water absorption.

SURFACE PREPARATIONIt should be noticed that the application surface is cured sufficiently. Anti-adhesion substances such as dust, oil, paint, silicone, curing agents, detergents, etc. should be removed from the application surface.



IMPLEMENTATIONPrimer 800 Exposed Concrete Primer is thinned with 1 kg of water per 3 kg and mixed until obtaining a homogenous mixture, and applied in single layer with a lambskin roller. Before proceeding with the implementation of the plaster the primer must be dried completely. Primer-water mixture should be mixed at intervals in order to keep it homogenous and it should not be collapsed. Specified periods of time are valid in at the surface and ambient temperature of 20 oC; the time increases in low temperature and decreases in high temperature.

CONSUMPTION200 - 250 g / m2 (depending on the surface), one layer


TECHNICAL SPECIFICATIONS Appearance Oxide pink colored cake Density 1.6 kg / lt. Application Temperature +5 ° C to +35 ° C Full hardening time 24 hours (Depending on temperature) Drying time 12 hours (depending on temperature) Dilution with water Ratio Primer 3 kg / 1 kg of water Shelf Life 1 year in original packaging

GENERAL PURPOSE ACRYLIC PRIMER

110

DESCRIPTIONAcrylic emulsion based, colorless, non-saponifiable, alkali-resistant and ready to use high adherence primer that is used in stabilization of dusty and highly absorbent grounds and has a very good binding property.

APPLICATION ARAESIt is used as adhesive on the surfaces with high porosity and absorption such as gypsum-plaster, gypsum-plasterboard, aerated concrete, plywood and chipboard for the interior and exterior applications for the horizontal and vertical applications; as adherence promoter before the primer and decorative primer applications; and as moisture protective for the surfaces where the final coating has been completed. It also used as impregnated primer in order to prevent the quick loss of water in adhesive mortar before the ceramic coating on the absorbent surfaces and to avoid falling the tiles in the process of time. It prevents sticking and cracking the plaster to be applied to the surface. The application of acrylic primer should be preferred espe-cially for the primers applied on the plates on the buildings which are being coated.

SURFACE PREPARATIONIt should be noticed that the application surface is cured sufficiently. Anti-adhesion substances such as dust, oil, paint, silicone, curing agents, detergents, etc. should be removed from the application surface.



IMPLEMENTATIONThe acrylic primer should be shaken before using and no water should be added. Before starting the application of decorative plaster, acrylic primer is applied to the surface as a single layer by means of lambskin roller, brush or spraying device. 20 minutes after the application process has been finished, decorative plaster can be applied. In other applications, it may be needed that it should be applied in two layers for very absorbent surfaces. It significantly reduces the absorbency of the application surface. Drying time is prolonged in wet weather conditions. Specified periods of time are valid in at the surface and ambient temperature of 20 oC; the time increases in low temperature and decreases in high temperature.

CONSUMPTION100-150 gr/m2 (single layer)


TECHNICAL SPECIFICATIONS Appearance White-colored liquid Density 1.03 kg / lt. Application Temperature Between +5 °C and +35 °C Full hardening time 6-8 hours. (Depending on temperature) Drying time 1-2 hours (depending on temperature) Second Floor Implementation Period 2-3 hours (depending on temperature) Shelf Life 1 year in original packaging

111

RAMMED ACRYLIC LINING

DESCRIPTIONIt is an acrylic emulsion based exterior primer; because it has high water vapor per-meability, it allows the moisture to come out. It prevents the formation of the salt in the structure. It also blocks the paints to be applied absorbed by the surface in different manner. It also have covering effect because it is rammed lining.

APPLICATION AREASIt is used as primer before the final layer application for the concrete, plaster and other raw walls, and inner and outer surfaces.

SURFACE PREPARATION AND IMPLEMENTATIONDirty, dusty and loose textured surfaces should be cleaned. However, if the salt out-put continues, it should not be applied until the reasons caused by this have been resolved. Brush, roller or spraying method may be used for the application. The rammed lining is thinned in 10-20% by volume and applied as single layer for the concrete, plaster and other raw walls before the final layer application. The final layer paint application should be made not before than 6 hours.


CONSUMPTION0,12 -0,150 kg /m2

STORAGEIt can be stored in its original packaging in closed environment at the temperatures between +5 oC and +30 oC for a period of one year. It can be stored in third row.

SAFETY WARNINGSR20-21-22: It is harmful in case of inhalation, swallowing and in contact with skin.S2: Keep out of the reach of children.S24-25: Keep away from contact with eyes and skin.S26: In case of contact with eyes, rinse plenty of water and seek medical advice.

TECHNICAL SPECIFICATIONS Color White Density 1.40 kg / lt. Application Temperature +5 °C and 35 °C. The duration of study 25 minutes at 25 ° C. Surface drying time 60-90 minutes at 25 ° C. Pack 15 lt. Practical Brush, roller and airless spray gun Cleaning used instruments Washed with water Thinner Used without thinning

RENK

STEEL FORM OIL

PLYWOOD FORM OIL

WOODEN FORM OIL

MOULD OILS

DESCRIPTIONIt is a special blend prepared with high quality mineral oil and chemicals. It is used to make easy to separate the steel forms from the concrete, to ensure being di-sassembled quickly the forms and being cleaned; and to obtain a smooth concrete surface.

APPLICATION AREASIt is used in all kinds of non-porous surfaces, especially steel molds; when it is used in steel, plastic molds it provides to remove the easily and quickly, and facilitates the mold clearance.

BENEFITSIt ensures easy removal of the mold and obtaining a smooth concrete. It facilitates the concrete to be placed into the form and removal of air bubbles; and make easi-er to clean the mold. It increases the efficiency and life of the mold which is used; significantly reduces the cost of the mold and labor. It does not create the problem of adherence; therefore it eliminates the use of paint and plaster on the concrete surfaces prior to the primer.

IMPLEMENTATIONBefore the use of form oil the forms must be clean. The application is made as a homogenous single layer on the mold surface with brush roller or spray. In order to achieve best performance a thin film of the product should be provided. Since the excess use of oil may cause spotting on the concrete, excess oil on the surface should be taken with sponge, cloth, etc. Newly applied mold surfaces should be protected from rain before concrete casting.

CONSUMPTIONDepending on the status, surface, type and separation method of the mould the sur-face of 25 to 30 m2 is coated with 1 liter.

TECHNICAL SPECIFICATIONS Color Clear dark yellow Content Mineral oil based fluid Density 0.85 to 0.90 gr/cm3 (20 oC) pH 6-8 Flash Point 95 oC

STEEL FORM OIL

114

DESCRIPTIONIt is a special blend obtained from the mixtures of high quality mineral oils and emul-sifiers and distillated water. It is used to make easy to separate the steel forms from the concrete in all kinds of absorptive mold surfaces, to ensure being disassembled quickly the forms and being cleaned; and to obtain a smooth concrete surface.

APPLICATION AREASIt is used in all kinds of non-porous surfaces, especially wooden molds; when it is used in Plywood, wooden molds it provides to remove the easily and quickly, and facilitates the mold clearance.




TECHNICAL SPECIFICATIONS Color Milk-white Content Mineral oil based emulsion Density 0.90 to 0.95 gr/cm3 (20 0C) pH 6-8 Flash Point non-flammable

PLYWOOD FORM OIL

115

DESCRIPTIONIt is a special blend obtained from the mixtures of high quality mineral oils and emul-sifiers and distillated water. It is used to make easy to separate the steel forms from the concrete in all kinds of absorptive mold surfaces, to ensure being disassembled quickly the forms and being cleaned; and to obtain a smooth concrete surface.

APPLICATION AREASIt is used in all kinds of non-porous surfaces, especially wooden molds; when it is used in Plywood, wooden molds it provides to remove the easily and quickly, and facilitates the mold clearance.




TECHNICAL SPECIFICATIONS Color Milk-white Content Mineral oil based emulsion Density 0.90 to 0.95 gr/cm3 (20 0C) pH 6-8 Flash Point non-flammable

WOODEN FORM OIL

116

WATERPROOFING MORTAR ADDITIVE

LATEX ADHERENCE AUGMENTER MORTAR ADDITIVE

ANTIFREEZE MORTAR ADDITIVE

SETTING RETARDER MORTAR ADDITIVE

PLASTICIZER MORTAR ADDITIVE

TICKENER MORTAR ADDITIVE

MORTAR ADDITIVES

DESCRIPTIONIt is the multi-purpose, liquid, water-repellent, non-saponifiable, alkali-resistant, setting retarding, strengthened, ready to use, latex mortar additive which is intro-duced into the cement mortars and has a very good binding property.

APPLICATION AREASIt is used for increasing the current flexibility, elasticity and water impermeability in repairing, easily implementing and strengthening the mortar, plaster, adherence bridge mortar, screed and spreading mortar; in obtaining crack-free, cement based repair mortar; in ensuring the adherence to the lower floor. It prevents premature drying of the mortar. It is used for strengthening the hydraulic binding systems. It can be used alone as a coating material for waterproofing to the painted surfaces.

SURFACE PREPARATIONApplication surface should be cured. Application surface should be cleaned from the anti-adhesion substances such as dust, oil, paint, silicone, curing material, deter-gent, etc.


APPLICATION FEATURESIt creates an elastic coating in large surfaces, does not shrink or crack. It provides excellent adhesion, reduces shrinkage, and increases mortar, plaster and screed strengths. It protects the equipment against corrosion. It is resistant to mort che-micals and mineral oils. It is ready to use and can be diluted with water.

120

IMPLEMENTATIONAll of the mortars which are reinforced with Fixkim water-repellent adhesion imp-roving mortar additive are applied to the mineral surfaces where moving parts are removed. Surface is slightly moistened before application. Clean and clear water is used by diluting at the prescribed mixture ratio according to the application type. The system is in the nature to give opportunity for the finishing process after the application. The minimum amount of mixture water should always be added to the mixture at the minimum amount in the first stages, and the remaining part should be added at the end of the mixture. This, at the same time, will help to achieve the desired consistency. Before using, suitability tests must be carried out. Caution: You must use cement or cement/lime as binder.

WARNINGSPacking must be mixed certainly before use. No material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood surfaces, metal surfaces and the surfaces exposed to the moisture. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immedia-tely, if necessary consult a doctor. Because it is acrylic-based product gloves should be worn during the application.


TECHNICAL SPECIFICATIONS Appearance White-colored liquid Density 1.05 kg / lt Application Temperature +5 °C to +35 °C Full hardening time 24 hours (Depending on temperature) Shelf Life 1 year in original packaging

WATERPROOFING MORTAR ADDITIVE

CONSUMPTION TYPE OF MORTAR CEMENT RATIO RATE OF SAND SAND particle size (mm) FH 101: water mixing ratio CONSUMPTION g/mAdherence bridge mortar 1 2 According to the 1:2 125 desired thickness Spreading Mortar 1 2 0-4 1:2 125Plaster, screed, repair mortar 1 5 - - -6-15 mm 1 3 0-2 1:3 4016 - 30 mm 1 3 0-4 1:4 3031-50 mm 1 3-4 0-8 1:6 22

121

DESCRIPTIONIt is the acrylic emulsion based, multi-purpose, liquid, non-saponifiable, alkali resis-tant, setting retarding, strengthened, ready to use mortar additive which is intro-duces into the cement mortars and has very good binging properties.

APPLICATION AREASIt is used in repair mortars, plasters, wear-resistant coatings, screeds, ceramic ad-hesive mortars, waterproofing mortars and all of the cement based mortars desired to have more adhesive resistance.



APPLICATION FEATURESIt creates an elastic coating in large surfaces, does not shrink or crack. It provides excellent adhesion, reduces shrinkage, and increases mortar, plaster and screed strengths. It protects the equipment against corrosion. It is resistant to mort che-micals and mineral oils. It is ready to use and can be diluted with water.

IMPLEMENTATIONFixkim adherence increasing mortar additive can be added directly to the dry mor-tar. In which product it will be added, it can be added in the water mixing ratio of that product. If requested, it can be diluted in the ratio of 1:5 by adding to the mixing water. The minimum amount of mixture water should always be added to the mixture at the minimum amount in the first stages, and the remaining part should be added at the end of the mixture. This, at the same time, will help to achieve the desired consistency. Before using, suitability tests must be carried out.

WARNINGSPacking must be mixed certainly before use. No material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. It cannot be applied in wood surfaces, metal surfaces and the surfaces exposed to the moisture. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immedia-tely, if necessary consult a doctor. Because it is acrylic-based product gloves should be worn during the application.

CONSUMPTIONIt varies according to the product and type of use.Example: 6 lt. of water is needed for 25 kg of thermal insulation plaster. For 6 lt. of water, about 1:5 antifreeze is added; the amount of water should be reduced in the amount of added antifreeze. (Volume 1,2 lt.).


TECHNICAL SPECIFICATIONS Appearance White-colored liquid Density 1.03 kg / lt. Application Temperature +5 ° C to +35 ° C Full hardening time 24 hours (Depending on temperature) Tack-free time 4-6 hours (depending on temperature) Second Floor Implementation Period 6-8 hours (depending on temperature) Shelf Life 1 year in original packaging

LATEX ADHERENCE AUGMENTER MORTAR ADDITIVE

DESCRIPTIONIt is setting accelerator effective mortar additive that is introduced into the cement based mortars and used for protecting from freezing in cool weather.

APPLICATION AREASIt is used in all cement-based mortars for protecting against freezing in repair mor-tars, plasters, wear-resistant coatings, screeds, ceramic adhesive mortars, ther-mal insulation mortars.


APPLICATION CONDITIONSIt should be considered that the ambient temperature is not under -10 oC during the application.

APPLICATION FEATURESIt ensures the cement hydration to dry quicker by accelerating the reaction betwe-en water and cement. So, hardening of the mortar is accelerated, freezing point of the water decreases and especially early resistance of the mortar increases. Alt-hough it is effective against frost, additional measures must be taken to hold the temperature of the concrete minimum 5-10 oC until the mortar reach at least 5 Mpa compressive strength.

122

IMPLEMENTATIONThe product for which Fixkim antifreeze mortar additive will be added, that product is diluted by adding 1:5 of the water mixing ratio into mortar water. Always the mini-mum amount of mixture water should be added into the mixture in the initial stages and remain should be added at the end of the mixture. This also will help to achieve the desired consistency. Before using, suitability tests must be carried out.

WARNINGSPacking must be mixed certainly before use. Excess dosage causes the flowing and cracking. No material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is acrylic-based product gloves should be worn during the application.

CONSUMPTIONIt varies according to the product and type of use.Example: 6 lt. of water is needed for 25 kg of thermal insulation plaster. For 6 lt. of water, about 1:5 antifreeze is added; the amount of water should be reduced in the amount of added antifreeze. (Volume 1,2 lt antifreeze 4,8 lt of water).


TECHNICAL SPECIFICATIONS Appearance Transparent liquid Density 1.03 kg / lt. Application Temperature 0 °C and -10 °C. pH 5.5 to 7.5 Chloride Content <0% (EN 480-10) Alkali <10% (EN 480-12) Shelf Life 1 year in original packaging

ANTIFREEZEMORTAR ADDITIVE

123

DESCRIPTIONIt is the setting retarder mortar additive that is introduced into the mortars and concrete, retards drying in the products with a fast drying due to the heat.

APPLICATION AREASIt is used in pouring the concrete and plaster applications in hot seasons, in smooth surfaced concrete and plaster applications for the adhesives drying quickly because of the wind and heat,



APPLICATION FEATURESIt allows for controlled application in hot climate conditions. In hot weather condi-tions setting time increases. The final strengths rise. It reduces the shrinkage and stretch; ensures a smooth concrete surface; does not include chloride and does not damage the equipment.

IMPLEMENTATIONIn which container the Fixkim Setting retarder additive is to be added; that product is diluted by adding the water in the ratio of 1:5 in the mortar water. Always the minimum amount of mixture water should be added into the mixture in the initial stages and remain should be added at the end of the mixture. This also will help to achieve the desired consistency. Before using, suitability tests must be carried out.


CONSUMPTIONIt varies according to the product and type of use.Example: 6 lt. of water is needed for 25 kg of thermal insulation plaster. For 6 lt. of water, about 1:5 setting retarder is added; the amount of water should be reduced in the amount of added setting retarder. (Volume 1,2 lt setting retarder 4,8 lt of water).


TECHNICAL SPECIFICATIONS Appearance Transparent gel-like liquid Density 1.1 kg / lt Application Temperature +5 °C to +35 °C pH 5,5 - 7 Chloride Content <0% (EN 480-10) Alkali <10% (EN 480-12) Shelf Life 1 year in original packaging

SETTING RETARDER MORTAR ADDITIVE

DESCRIPTIONIt is the super plasticizer liquid additive that is introduced into the cement mortars, reduces the mixing water and increases the fluidity.

APPLICATION AREASIt is used as super plasticizer into the concrete for the places where early molding in needed; for the lubricity into the plaster mortar; to avoid space in the reinfor-ced concrete; in order to reduce water permeability in base concretes; for easier concreting in cold climatic conditions; to ensure the easy dispersion in base screeds.



APPLICATION FEATURESIn the mixtures with low powder grading, it improves the workability of the mixtu-re and prevents the formation of a surface. It reduces the amount of water in the mixture, so increases the strength and durability of the mixture. It is used in the products that provide high strength at low temperatures.

124

IMPLEMENTATIONIn which container the Fixkim plasticizer mortar additive is to be added; that product is diluted by adding the water in the ratio of 1:5 in the mortar water. Always the minimum amount of mixture water should be added into the mixture in the initial stages and remain should be added at the end of the mixture. This also will help to achieve the desired consistency. Before using, suitability tests must be carried out.


CONSUMPTIONIt varies according to the product and type of use.Example: 6 lt. of water is needed for 25 kg of thermal insulation plaster. For 6 lt. of water, about 1:5 plasticizers are added; the amount of water should be reduced in the amount of added plasticizer. (Volume 1,2 lt plasticizer 4,8 lt of water).


TECHNICAL SPECIFICATIONS Appearance Transparent gel-like liquid Density 1.1 kg / lt Application Temperature +5 °C to +35 °C pH 7 – 7,5 Chloride Content <0% (EN 480-10) Alkali <10% (EN 480-12) Shelf Life 1 year in original packaging

PLASTICIZER MORTAR ADDITIVE

125

DESCRIPTIONIt is liquid additive that is introduced into the cement mortars and concrete, reduces the consistency of the liquid mortar and stems the tide of its liquidity.

APPLICATION AREASIt is used for the adjusting the consistency in flowing an gloating plasters, tile adhe-sives, granite adhesives.



APPLICATION FEATURESBy stopping the flowing and floating caused by extreme dilution in the mortars and concrete and features to the product with thixotropic property. It ensures the cont-rolled applications. It increases the final strengths reduces the shrinkages and cre-eping. In ensures to achieve a smooth concrete surface. It does not contain chloride and does not damage the equipment.

IMPLEMENTATIONIn which container the (Fixkim thickener mortar) mortar additive is to be added; that product is diluted by adding the water in the ratio of 1:10 in the mortar water. Always the minimum amount of mixture water should be added into the mixture in the initial stages and remain should be added at the end of the mixture. This also will help to achieve the desired consistency. Before using, suitability tests must be carried out.

WARNINGSPacking must be mixed certainly before use. In the event of excess dosage it makes different the mortar consistency, top drying is accelerated and internal drying is reduces the flowing and it causes for cracking. No material (lime, cement, gypsum, etc.) should be added into the prepared mortar. The expired mortars should not be used again by mixing with water or dry mortar. It should not be applied on the hot surfaces exposed to the sunlight for a long time or frozen surfaces. Avoid inhalation, in case of contact with eyes rinse with a plenty of water immediately, if necessary consult a doctor. Because it is acrylic-based product gloves should be worn during the application.

CONSUMPTIONIt varies according to the product and type of use.Example: 6 lt. of water is needed for 25 kg of thermal insulation plaster. For 6 lt. of water, about 1:10 thickener moistures added; the amount of water should be re-duced in the amount of added thickener. (Volume 0,6 lt plasticizer 5,4 lt of water).


TECHNICAL SPECIFICATIONS Appearance Transparent liquid Density 1 kg / lt Application Temperature +5 °C to +35 °C pH 6,5 – 7,5 Chloride Content <0% (EN 480-10) Shelf Life 1 year in original packaging

TICKENER MORTAR ADDITIVE

SC 600 SELF-LEVELLING COATING

SC 605 EPOXY PAINT

CHLORINATED RUBBER MARKING PAINT

EPOXY COATINGS AND PAINTS

DESCRIPTIONTwo-component, solvent-free, epoxy resin based, self-leveling coating.

APPLICATION AREASIt is a solvent-free epoxy coating that is used in factories, assembly plants, wa-rehouses, aircraft hangars, shops, car parks, food facilities, hospitals, chemical and pharmaceutical industries, power plants, hygiene required units and all industrial grounds; having high mechanical strength and abrasion resistance, easy to clean and can be used on the last layer of the multilayer system or self-leveling alone.

SURFACE PREPARATIONThe application surfaces should be cleaned from greases, dusts and dirt. The free parts on the surface, cement slurry on the concrete surfaces and the parts preven-ting the adhesion should be cleaned.

MIXTURE PREPARATIONComponent A and B should be mixed with a low speed mixer at least 3 – 4 minutes until obtaining a homogenous mixture by considering the mixing ratio. After mixing it is ready to use.

COATING SYSTEMThe surface to be applied must be lined with SC 210 – SC 215 or SC 270 surface screed. SC 220 must be used on the dump surfaces. 12 hours after lining process, coating operation can be started. The product prepared in a mixture is poured to the surfa-ce, and spread uniformly on the surface by selecting a notched trowel (tooth spacing of 1 mm or 2 mm) depending on the desired thickness; the air bubbles are removed with a spiked roller. In the brush and roller applications, epoxy roller must be used. Since the roller will leave the thickness of 200-300 micron, it should be applied in 2-3 layers in order to reach to the desired thickness. In the cases that high UV resistan-ce 0,15 to 0,2 kg PU 125 protective coating application is recommended.

SC 600 SELF-LEVELLING COATING

128

APPLICATION CONDITIONS- The surfaces must have adequate strength. The concrete must be resistant to 25 N/mm2 pressure and have at least 1,5 to 2 N/mm2 tensile strength.- The surface must be clean, smooth and dry and must not exceed humidity of 5%; if the humidity is above this value, SC 200 100% Dump Surface Screed which is used for dump surfaces must be used.- Before starting the upper layer coating, the coating must be cured completely.- Do not apply below 10 oC and at very humid environments.- Mixing ratios should be considered.


HANDLING and STORAGE- The product should be kept between the temperatures of 5 and 35 oC.- The product should not be exposed to direct sunlight.- Unopened product should be maintained in its original packaging and by closing the lid firmly.

NOTEFİXKİM reserves the right to make improvement/revision in the product and in this technical document in time. This Technical Data Sheet invalidates the Tech-nical Data Sheet previously published for this product and valid for 5 years. The user should make sure that the technical document in his hand is the most current version, if necessary, he should questioned the timeliness of the document from the company. Whether the product is being used for the purpose of the product or not, and the validity of the application conditions and formations are under the res-ponsibility of the practitioner. FİXKİM Epoxy Paint does not accept any guarantee requests regarding the results, work accidents, direct or indirect loss or damages arising from the application of the products as being recommended. The packaging values specified above the nominal values in the formulations standardized by FİX-KİM. Under the normal production conditions, slight deviations prescribed in the international standards may occur.

TECHNICAL SPECIFICATIONS Color RAL colors View Bright Solids by weight 98% Density 1.55 g / cm3


Flash point > 25 °C Mixing Ratio 5/1 Application Methods Brush, Roller, Airless Spray Gun, Mala Pot Life 30 min / 25 °C Shelf Life 1 year Waiting time between coats 12 hours / 25 °C Drying Time 12 hours at 25 °C Mechanical Strength 7 days Shore D Hardness 75 (7 days / 25 °C) Equipment Cleaning Epoxy Thinner

3,517,5

129

DESCRIPTIONTwo-component, solvent-free, epoxy resin based, epoxy last layer paint that can be used also in vertical surfaces.

APPLICATION AREASIt is a solvent-free epoxy paint that is used in factories, assembly plants, wareho-uses, aircraft hangars, shops, car parks, food facilities, water tanks, hospitals, che-mical and pharmaceutical industries, power plants, hygiene required units and all industrial grounds; having high mechanical strength and abrasion resistance, easy to clean and can be used in vertical surfaces.

SURFACE PREPARATIONThe application surfaces should be cleaned from greases, dusts and dirt. The free parts on the surface, cement slurry on the concrete surfaces and the parts preven-ting the adhesion should be cleaned.


COATING SYSTEMThe surface to be applied must be lined with SC 210 or SC 270 surface screed. SC 220 must be used on the dump surfaces. 12 hours after lining process, painting operation can be started. In the brush and roller applications, epoxy roller must be used. If required the product can be used as the first layer screed also. In the cases that high UV resistance 0,150 to 0,200 kg PU 125 protective coating application is recom-mended.

APPLICATION CONDITIONS- The surfaces must have adequate strength. The concrete must be resistant to at least 25 N/mm2 pressure and have at least 1,5 to 2 N/mm2 tensile strength.- The surface must be clean, smooth and dry and must not exceed humidity of 5%; if the humidity is above this value, SC 200 100% Dump Surface Screed which is used for dump surfaces must be used.- Before starting the upper layer coating, the coating must complete the curing.- Do not apply below 10 oC and at very humid environments.- Mixing ratios should be considered.

SAFETYThe product is for professional use. Please note the safety instructions on the package before using, if necessary, see the Material Safety Data Sheet. Do not inhale, avoid contact with skin and eyes, do not ingest, use the appropriate safety equipment. Take the necessary measures to prevent pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas.


NOTEFİXKİM reserves the right to make improvement/revision in the product and in this technical document in time. This Technical Data Sheet invalidates the Technical Data Sheet previously published for this product and valid for 5 years. The user should make sure that the technical document in his hand is the most current ver-sion, if necessary, he should questioned the timeliness of the document from the company. Whether the product is being used for the purpose of the product or not, and the validity of the application conditions and formations are under the res-ponsibility of the practitioner. FİXKİM Epoxy Paint does not accept any guarantee requests regarding the results, work accidents, direct or indirect loss or damages arising from the application of the products as being recommended. The packaging values specified above the nominal values in the formulations standardized by FİX-KİM. Under the normal production conditions, slight deviations prescribed in the international standards may occur.

SC 605 EPOXY PAINT

TECHNICAL SPECIFICATIONS Color RAL colors View Bright Solids by weight 98% Density 1.50 g / cm3


Flash point > 25 °C Mixing Ratio 5/1 Application Methods Brush, Roller, Airless Spray Gun, Mala Pot Life 30 min / 25 °C Shelf Life 1 year Waiting time between coats 12 hours / 25 °C Drying Time 12 hours at 25 °C Mechanical Strength 7 days Shore D Hardness 75 (7 days / 25 °C) Equipment Cleaning Epoxy Thinner

3,517,5

DESCRIPTIONAir-drying, alkyd based, high adhesion, enriched with chlorinated road drawing and marking paint.

APPLICATION AREASIt resistant to external conditions, frictions, atmospheric effects and used in road drawings and markings in the concrete, asphalt, and thin plastered surfaces in high-ways, airways and car parkıng facilities.

SURFACE PREPARATION AND IMPLEMENTATIONThe application surfaces should be cleaned from the materials which prevent ad-hesion such as greases, paints, dusts, dirt, etc. The material should be mixed tho-roughly and used by thinning with appropriate thinner at the ratio of 10% to 15%.

APPLICATION CONDITIONSIt should be considered that the ambient temperature is between +5 oC and +30 oC.

CONSUMPTION0,350 – 0,400 kg/m2 (Duplex)

STORAGEIt can be stored in its original packaging at the temperature of +5 oC and +30 oC indoors. It should be stored in the third raw.

SAFETY WARNINGS

R10: FlammableR20-21-22: It is harmful in case of inhalation, swallowing and in contact with skin.S2: Keep out of the reach of children.S20-21: Do not eat or drink when you are working.S24-25: Keep away from contact with eyes and skin.S26: In case of contact with eyes, rinse plenty of water and seek medical advice.S36-37-39: Wear suitable protecting clothing, gloves, and goggles and face protec-tion mask when you are working.S-36: It is irritative for eyes.S-38: It irritates the skin.S-42: It may cause sensitization by inhalation.

TECHNICAL SPECIFICATIONS Color White and Yellow Viscosity 100-110 Application Temperature +5 °C and 35 °C. Contact time 15 min at 20° C Opening time for traffic 30-60 minutes at 20 ° C Packaging 20 kg Application Brush, Roller, Airless Spray Gun Cleaning used instruments Cleaned with thinner Thinner Thinner Drying time between coats 180 minutes at 25 ° C.

CHLORINATED RUBBER MARKING PAINT

130

20

SC 270 PRIMER

SC 220 PRIMER

SC 210 PRIMER

NATURAL STONE PROTECTOR

EPOXY PRIMERS

DESCRIPTIONTwo-component, solvent epoxy resin based, low viscosity impregnated primer and bonding bridge.

APPLICATION AREASIt prevents water absorption by filling the capillary pores on the concrete surfaces; improves the bonding between the layers and creates adhesion bridge.

SURFACE PREPARATIONThe application surfaces should be cleaned completely from the free parts and the surfaces should be roughened mechanically (blast rack or milling) and purged from the dust with vacuum cleaner.


APPLICATION CONDITIONS- The surfaces must have adequate strength. The concrete must be resistant to at least 25 N/mm2 pressure and have at least 1,5 to 2 N/mm2 tensile strength.- The surface must be clean, smooth and dry and must not exceed humidity of 5%; if the humidity is above this value, SC 200 100% Dump Surface Screed which is used for dump surfaces must be used.- Before starting the upper layer coating, the coating must complete the SC 270 curing.- Do not apply below 10 oC and at very humid environments.- Mixing ratios should be considered.

SC 270 PRIMER

134

SAFETYThe product is for professional use. Please note the safety instructions on the package before using, if necessary, see the Material Safety Data Sheet. Do not inhale, avoid contact with skin and eyes, do not ingest, use the appropriate safety equipment. Take the necessary measures to prevent pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas.


NOTEFİXKİM reserves the right to make improvement/revision in the product and in this technical document in time. This Technical Data Sheet invalidates the Technical Data Sheet previously published for this product and valid for 5 years. The user should make sure that the technical document in his hand is the most current version, if necessary, he should questioned the timeliness of the document from the company. Whether the product is being used for the purpose of the product or not, and the validity of the application conditions and formations are under the responsibility of the practitioner. FİXKİM Epoxy Paint does not accept any guarantee requests regarding the results, work accidents, direct or indirect loss or damages arising from the application of the products as being recommended. The packaging values specified above the nominal values in the formulations standardized by FİXKİM. Under the normal production con-ditions, slight deviations prescribed in the international standards may occur.

TECHNICAL SPECIFICATIONS Color Colorless View Transparent Thinner Epoxy Thinner Solids by weight 44% Density 0.93 g / cm3


Flash point > 25 ° C Mixing Ratio 4:1 Application Methods Brush, Roller, Air Spray Gun, Airless Spray Gun Pot Life 4 hours / 25 °C Shelf Life 1 year Waiting time between coats 12 hours / 25 °C Drying Time 12 hours at 25 °C Mechanical Strength 7 days Equipment Cleaning Epoxy Thinner

416

135

DESCRIPTIONIt is two-component, solvent-free epoxy resin based epoxy primer that penetrates to the capillaries in the concrete and forms moisture barrier for 100% humid and wet surfaces.

APPLICATION AREASIt is used as the humid surface concrete primer prior to the application of epoxy, pol-yurethane and polyuria in the factory and warehouse floors, working areas, loading zones and industrial floors exposed to medium and heavy loads.

SURFACE PREPARATIONThe application surfaces should be cleaned completely from the free parts and paint residues, breaks and cracks should be repaired and the surfaces should be roug-hened mechanically (blast rack or milling) and purged from the dust with vacuum cleaner.


APPLICATION CONDITIONS- The surfaces must have adequate strength. The concrete must be resistant to at least 25 N/mm2 pressure and have at least 1,5 to 2 N/mm2 tensile strength.- Before starting the upper layer coating, the coating must complete the SC 220 curing.- Do not apply below 10 oC.- Mixing ratios should be considered.

SAFETYThe product is for professional use. Please note the safety instructions on the packa-ge before using, if necessary, see the Material Safety Data Sheet. Do not inhale, avoid contact with skin and eyes, do not ingest, use the appropriate safety equipment. Take the necessary measures to prevent pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas.


NOTEFİXKİM reserves the right to make improvement/revision in the product and in this technical document in time. This Technical Data Sheet invalidates the Technical Data Sheet previously published for this product and valid for 5 years. The user should make sure that the technical document in his hand is the most current version, if necessary, he should questioned the timeliness of the document from the company. Whether the product is being used for the purpose of the product or not, and the validity of the application conditions and formations are under the responsibility of the practitioner. FİXKİM Epoxy Paint does not accept any guarantee requests re-garding the results, work accidents, direct or indirect loss or damages arising from the application of the products as being recommended. The packaging values spe-cified above the nominal values in the formulations standardized by FİXKİM. Under the normal production conditions, slight deviations prescribed in the international standards may occur.

SC 220 PRIMER

TECHNICAL SPECIFICATIONS Color Beige View Blurred Thinner - Solids by weight 92% Density 1.20 g / cm3

Consumption 0,3 - 0,5 kg / m2

Flash point > 25 °C Mixing Ratio 2.4 / 1 Application Methods Brush, roller, trowel Pot Life 40 min / 25 °C Shelf Life 1 year Waiting time between coats 12 hours / 25 ° C Drying Time 12 hours at 25 °C Mechanical Strength 7 days Equipment Cleaning Epoxy Thinner

512

DESCRIPTIONIt is two-component, epoxy resin based epoxy primer that contains low ratio of sol-vent.

APPLICATION AREASIt is used as the layer of primer on the epoxy based mortars or prior to epoxy, pol-yurethane lop layer application in factory and warehouse floors, working areas, lo-ading zones, industrial floors exposed to medium and heavy load, concrete surfaces, cement mortars and screed surfaces and very absorbent surfaces.

SURFACE PREPARATIONThe application surfaces should be cleaned completely from the free parts and paint residues, breaks and cracks should be repaired and the surfaces should be roug-hened mechanically (blast rack or milling) and purged from the dust with vacuum cleaner.


APPLICATION CONDITIONS- The surfaces must have adequate strength. The concrete must be resistant to at least 25 N/mm2 pressure and have at least 1,5 to 2 N/mm2 tensile strength.- The surface must be clean, smooth and dry and must not exceed humidity of 5%; if the humidity is above this value, SC 220 100% Dump Surface Screed which is used for dump surfaces must be used.- Before starting the upper layer coating, the coating must complete the SC 210 curing.- Do not apply below 10 oC.- Mixing ratios should be considered.

SC 210 PRIMER

136




TECHNICAL SPECIFICATIONS Color Transparent View Flat paint Thinner Epoxy Thinner Solids by weight 86% Density 1 g / cm3


Flash point > 25 ° C Mixing Ratio 2.5 / 1 Application Methods Brush, roller, trowel, Air Gun, Airless Spray Gun Pot Life 60 min / 25 ° C Shelf Life 1 year Waiting time between coats 12 hours / 25 ° C Drying Time 12 hours at 25 ° C Mechanical Strength 7 days Equipment Cleaning Epoxy Thinner

512,5

137

DESCRIPTIONIt is one-component, acrylic polyurethane based, transparent, concrete and natural stone protector with solvent and having high penetration feature.

APPLICATION AREASAll kinds of concrete and mineral surfaces, mosaic surfaces and natural stones (marble, travertine, slate, granite, synthetic and natural stone slabs)

PRODUCT FEATURES- Easy to apply,- With high penetration capability,- Resistant to UV rays.- Waterproofing- Protective against the products which creates alkaline and acidic stain (tea, cof-fee, ketchup, mayonnaise, cola, etc.)- Because it creates a hard and durable surface. - It creates a decorative and aesthetic appearance on the surfaces.- Slightly wet view is formed on the application surface.

SURFACE PREPARATIONThe application surfaces should be cleaned from grease, dirt, rust, dust and an all kinds of residuals.

APPLICATION CONDITIONSIt is ready for use. It should be applied at least twice on the textured and rough surfaces with high absorbent feature. It should be applied by at least 1 hour of break between two layers. Testing of the full performance of the product must be done at least 24 hours later. For the applications which will be made in closed areas the environment should be ventilated completely. You must not smoke and inhale the solvent vapors.

SAFETYPlease note the safety instructions on the package before using, if necessary, see the Material Safety Data Sheet. Do not inhale, avoid contact with skin and eyes, do not ingest, use the appropriate safety equipment. Take the necessary measures to prevent pollution of environment in addition to fire and explosion hazard. Apply in well ventilated areas.

HANDLING and STORAGE- TK 055 should be stored in cool and covered place at the perpendicular manner. It should not be exposed to direct sunlight.- Its shelf life is 12 months when it stored in its unopened package in cool and dry conditions.


NATURAL STONE PROTECTOR

TECHNICAL SPECIFICATIONS Color Transparent View Bright Thinner Ready to use Density 0.95 g/cm3

Consumption Depending on the smoothness and absorption conditions of application; 150 gr / m2 to 250 gr in one floor. Application Methods Brush, roller, conventional or airless spray gun Application Temperature +5 ° C - + 30 ° C Shelf Life 1 year Drying Time Full cure 24 hours Equipment Cleaning Cellulosic Thinner

EXTERIOR PAINTS

SILICONE EXTERIOR PAINT

ACRYLIC EXTERIOR PAINT

THERMAL EXTERIOR PAINT

SILICONE EXTERIOR COATING

ACRYLIC EXTRIOR COATING



140

DESCRIPTIONIt is water based, silicone enhanced, matt, acrylic copolymer binder based, building exterior finishing paint.

APPLICATION AREASIt can be applied on the silicate or acrylic based paints which can carry itself for re-novation works in all kind of concrete, plaster, spreader, comb, concrete and mineral surfaces. Due to high ability of breathing, it is strongly recommended for top of the thermal insulation systems.

IMPLEMENTATIONAfter the application surface is cleaned from all kinds of oil, dirt, rust, loose and swollen layers and the dusts that prevent to adhesion of finishing paint and primer, the surface is prime coated with Fixkim primer suitable surface type. After the primer has been dried, Fixkim Silicone Exterior Paint is thinned with water by the ratio of 15 to 20% and applied in two layers on the surface. It is recommended to wait for 2 hours between the layers of the paint. You must take care that surface temperature is between +5 oC and +30 oC during the application. Avoid application in direct sunlight and wind. It is recommended that the material used in the application should be cleaned with water.

CONSUMPTIONDepending on the surface smoothness and porosity, in single layer, 10-11 m2/L should be made controlled sampling for final consumption.

STORAGEIt can be stored in a cool place protected from frost for 1 year.

RISK WARNINGSR 43: It is possibly increase the sensitization by skin contact.

SAFETY WARNINGSS 2: Keep away from children.S 23: Do not breathe gas/fume/vapor/aerosol.S 24: Avoid contact with skin.S 46: If swallowed, seek medical advice immediately and show the package or label.

Compatible with TS 7847.

TECHNICAL SPECIFICATIONS Color Standard colors of the chart (it can be produced in desired colors.) Density 1.40 ± 100 g / cm3

Dry Heat Resistance Between -25 °C and +180 °C Application Temperature Between +5 °C and 35 °C Tack-free time 30 minutes at 25 °C Surface drying time 60 minutes at 25 °C Implementation Brush, Roller, Airless Spray Gun Cleaning used instruments Washed with water Thinner Drinking water Drying time between coats 120 minutes at 25 °C

141

ACRYLIC EXTERIOR PAINT

DESCRIPTIONIt is water based; matt, acrylic copolymer binder based building exterior finishing paint.

APPLICATION AREASIt can be applied on the silicate or acrylic based paints which can carry itself for re-novation works in all kind of concrete, plaster, spreader, comb, concrete and mineral surfaces. Due to high ability of breathing, it is strongly recommended for top of the thermal insulation systems.

IMPLEMENTATIONAfter the application surface is cleaned from all kinds of oil, dirt, rust, loose and swollen layers and the dusts that prevent to adhesion of finishing paint and primer, the surface is prime coated with Fixkim primer suitable surface type. After the primer has been dried, Fixkim Silicone Exterior Paint is thinned with water by the ratio of 15 to 20% and applied in two layers on the surface. It is recommended to wait for 2 hours between the layers of the paint. You must take care that surface temperature is between +5 oC and +30 oC during the application. Avoid application in direct sunlight and wind. It is recommended that the material used in the application should be cleaned with water.

CONSUMPTIONDepending on the surface smoothness and porosity, in single layer, 10-11 m2/L should be made controlled sampling for final consumption.





TECHNICAL SPECIFICATIONS Color Standard colors of the chart (it can be produced in desired colors.) Density 1.40 ± 100 g / cm3


THERMALEXTERIOR PAINT

142

DESCRIPTIONIt is water based, single component, flexible, high UV resistant, energy-saving in-terior and exterior paint including the micro ceramic-spheres with low thermal conductivity. By means of its heat-reflective property by force of micro-sphere ceramics in the product it ensures 25% energy savings. It reflects 95% of the sun lights and 85% of the UV rays. It ensures the heat insulation up to 40% in the di-rect proportion to the number of coats applied for radiant heat resistance. It also ensures up to 25% of heat insulation since it reflects the heat on the interior front.

APPLICATION AREASIt is used in interior and exterior facades and sloped roofs.

SURFACE PREPARATIONMolding oil, dust, paint dirt and other materials to prevent the adhesion must be removed from the application surface. The surface defects must be corrected with Fixkim Repair Mortars. The product must be applied with brush or roller on the sur-face by thinning by 10% with water.


APPLICATION FEATUREASApplication thickness: 1 to 1.5 mm. The time to wait between coats: 24 hours

IMPLEMENTATIONUndiluted product is applied on the surface of the primed surface, the application layers must be applied as a multiple cross each other. The applied surface should not be exposed to frost within 24 hours.

CONSUMPTION1,5 to 2,00 kg / m2 for the thickness of 1 mm.

STORAGEIt can be stored in its original packaging in closed environment at the temperatures between +5 oC and +30 oC for a period of one year. It can be stored in third row.

SAFETY WARNINGSS 2: Keep out of the reach of children.S 13: Keep away from food, drink and animal feedingS 24: Keep away from contact with eyes.S 26: In case of contact with eyes, rinse plenty of water and seek medical advice.S 46: If swallowed, seek medical advice immediately and show the label to the physi-cian.

TECHNICAL SPECIFICATIONS Color Standard white and grey (if desired specific colors can be produced.) Powder Density 1.20 ± 100 g / cm3

Dry Heat Resistance Between -25 °C and +180 °C Application Temperature +5 °C and 35 °C Tack-free time 30 minutes at 25 °C Surface drying time 60 minutes at 25 °CPacking 20 kg Implementation Brush, Roller, Airless Spray Gun Cleaning used instruments Washed with water Thinner Drinking water Drying time between coats 120 minutes at 25 °C

143

SILICONE EXTERIOR COATING

DESCRIPTIONIt is water based, acrylic copolymer resin founded, matt, grainy exterior finishing silicone coat that is applied with a roller and can be patterned with a coral roller.

APPLICATION AREASIt can be applied on the silicate or acrylic based paints which can carry itself for re-novation works in all kind of concrete, plaster, spreader, comb, concrete and mineral surfaces. It is applied in desired thickness with different types of rollers optionally. It has high adhesion strength; will not crack. Its alkali resistance is too high. Due to the silicone included in the product the surface will not be wet, so front pollution would be too late. Due to high ability of breathing, it is strongly recommended for top of the thermal insulation systems.

IMPLEMENTATIONAfter the application surface is cleaned from all kinds of oil, dirt, rust, loose and swollen layers and the dusts that prevent to adhesion of finishing paint and primer, the surface is prime coated with Fixkim primer suitable surface type. After the primer has been dried, Fixkim Silicone Exterior Coating is thinned with 1-1,5 kg of water in 25 kg of packing and spread on the surface with yarn or lambskin roller; before the material dries the application is finished with coral roller by giving a pattern. It is recommended to wait for 2 hours between the layers of the paint. You must take care that surface temperature is between +5 oC and +30 oC during the application. Avoid application in direct sunlight and wind. It is recommended that the material used in the application should be cleaned with water.

CONSUMPTIONDepending on the porosity and smoothness of the surface 900-1200 gr/m2 should be made controlled sampling for final consumption.





TECHNICAL SPECIFICATIONS Color Standard colors of the chart (it can be produced in desired colors.) Density ≥ 1.40 ± 100 g / cm3


ACRYLIC EXTERIOR COATING

144

DESCRIPTIONIt is water based, acrylic copolymer binding founded, matt, grainy exterior finishing coat that is applied with a roller and can be patterned with a coral roller.

APPLICATION AREASIt can be applied on the silicate or acrylic based paints which can carry itself for re-novation works in all kind of concrete, plaster, spreader, comb, concrete and mineral surfaces. It is applied in desired thickness with different types of rollers optionally. It has high adhesion strength; will not crack. Its alkali resistance is too high. Due to the silicone included in the product the surface will not be wet, so front pollution would be too late. Due to high ability of breathing, it is strongly recommended for top of the thermal insulation systems.

IMPLEMENTATIONAfter the application surface is cleaned from all kinds of oil, dirt, rust, loose and swollen layers and the dusts that prevent to adhesion of finishing paint and primer, the surface is prime coated with Fixkim primer suitable surface type. After the primer has been dried, Fixkim Silicone Exterior Coating is thinned with 1-1,5 kg of water in 25 kg of packing and spread on the surface with yarn or lambskin roller; before the material dries the application is finished with coral roller by giving a pattern. You must take care that surface temperature is between +5 oC and +30 oC during the application. Avoid application in direct sunlight and wind. It is recommended that the material used in the application should be cleaned with water.

CONSUMPTIONDepending on the porosity and smoothness of the surface 900-1200 gr/m2 should be made controlled sampling for final consumption.





TECHNICAL SPECIFICATIONS Color Standard colors of the chart (it can be produced in desired colors.) Density ≥ 1.40 ± 100 g / cm 3

Dry Heat Resistance Between -25 °C and +180 °C Application Temperature Between +5 °C and 35 °C. Tack-free time 30 minutes at 25 °C. Surface drying time 60 minutes at 25 °C. Implementation Brush, Roller, Airless Spray Gun Cleaning used instruments Washed with water Thinner Drinking water Drying time between coats 120 minutes at 25 °C.

MACHINE-APPLIED PLASTER

SATIN PLASTER

PERLITIC GYPSUM

MOULDING PLASTER

GYPSUM PRODUCTS

148

WHAT IS IT?Machine Plaster Gypsum is gypsum based interior plaster with enhanced insulation properties and applied with the machine. It creates a surface in single layer and smooth and ready to paint directly on the materials such as brick, concrete, exposed concrete, gas concrete, and pumice blocks, etc.It does not require satin polish gypsum. Because it is applied by spraying, it easily adheres to the surface; does not collapse, creep or crack. In the details, like door and window borders, it can be applied seamlessly with the mixture to be applied by hand. After hardening, the surface hardness gains high strength and brighter appearance. It is a non-combustible material. It balances the humidity and it is healthy. It provides heat and sound insulation. Since it is applied by spraying, greater surface is plastered. It is economical, saves time and labor cost.

WHERE TO USE IT?It is applied on the surface such as gypsum plaster, exposed concrete, gas concrete, pumice blocks and brick.

TECHNICAL SPECIFICATIONS Physical Form White powder Gypsum / Water Ratio 100 gr. gypsum, 60 g. water Using time 140-200 minutes Hardening Time 320-360 minutes Pressure Strength After 7 days;> 2 N / mm2

Bending Strength After 7 days,> 1 N / mm2

Unit Weight 740 gr / lt. Particle Size 25-30% over 150 micron 4-10% over 600 microns pH 13-14 Surface Hardness Minimum of 45 shore D is applied. Consumption For a thickness of 1 cm 9-9.5 Kg. / m2

MACHINE-APPLIED PLASTER

WHAT IS IT?The satin polishing plaster is a surface smoothing plaster that can be used as undercoat for all painting sur-faces. By means of its enhanced chemical structure, it fills the gaps, roughs the edges off, and destroys the texture differences, surface defects and mould errors on the application surface. It creates a smooth and aesthetic surface without needing the paste for plastic paint, wallpaper and decorative coatings. It can be applied on the dry surfaces. It saves the paint, it is economical. It has a high adhesion property.

WHERE TO USE IT?It is applied on the surface of gypsum plaster, exposed concrete and gypsum wall boards.

TECHNICAL SPECIFICATIONS Physical Form White powder Plaster / Water Ratio 100 gr. gypsum, 70 g. water Using time 160 - 200 minutes Freezing Time 320 - 360 minutes Pressure Strength After 7 days; > 2 N / mm2

Bending Strength After 7 days; > 1 N / mm2

Unit Weight 670 g / lt. Particle Size 9-15% over 45 microns 0 to 0.15% over 160 microns pH 7-8 Surface Hardness 40 shore D is applied. Consumption On the gypsum plaster 0.8 to 1.1 Kg. / m2 On the plaster board 0.8 to 1.0 Kg. / m2

149

SATIN PLASTER

150

WHAT IS IT?The perlitic plaster gypsum is gypsum based interior plaster with improve sound and head insulation properties. Thanks to the long processing time it ensures ease of use and allows the application without loss. During the hardening time period; it does not collapse, creep or crack. By means of smooth and bright surface, it allows wallpaper coating and painting process directly. Owing to its enhanced chemical structure it balances the moisture ratio in the environment, it breathes and it is healthy. It is resistant to the fire. It retards to spread the fire. It ensures sound and heat insulation. It does not allow for growth of the bacteria, mold and fungi; it is human and environmental friendly.

WHERE TO USE IT?It is used for concrete, gas concrete, exposed concrete, pumice block, bricks and ceiling surfaces in plastering the inner surface of the ceiling and ground.

TECHNICAL SPECIFICATIONS Physical Form White powder Plaster / Water Ratio 100 gr. gypsum, 62 gr. water Using time 120 - 160 minutes Freezing Time 300-330 minutes Pressure Strength After 7 days; > 2 N / mm2

Bending Strength After 7 days; > 1 N / mm2

Unit Weight 750 gr / lt. Particle Size 25 - 30% over 150 microns 0 to 1.0% over 600 microns pH 13 - 14 Surface Hardness 40 shore D is applied. Consumption of 1 cm thickness 8.5 to 10 Kg. / m2

PERLITIC GYPSUM

WHAT IS IT?Moulding plaster is a decorative aimed construction plaster consisting of fine gypsum. Thanks to the long processing time it ensures ease of use and allows the application without filtering. During the hardening time period; it does not collapse, creep or crack. By means of smooth and bright surface, it allows wallpaper coating and painting process directly. Owing to its enhanced chemical structure it balances the moisture ratio in the environment, it breathes and it is healthy. It is resistant to the fire. It retards to spread the fire. It ensures sound and heat insulation. It does not allow for growth of the bacteria, mold and fungi; it is human and environmental friendly.

WHERE TO USE IT?It is used in decorative applications and carton-pierre implementations.

TECHNICAL SPECIFICATIONS Physical Form White powder Plaster / Water Ratio 100 gr. gypsum, 70 g. water Using time 7 - 12 minutes Freezing Time 20-30 minutes Pressure Strength After 7 days;> 8 N / mm2

Bending Strength After 7 days;> 3 N / mm2

Unit Weight 645 gr / lt. Particle Size 8 - 10% over 45 microns 0 to 1.0% over 160 microns pH 7 -8 Surface Hardness 60 shore D is applied.

151

MOULDING PLASTER

MEMBRANES

FIXKIM MEMBRANEF 2000 – F 3000P 3000 – P 4000

ALM 3000ARD 4000

POWERMIX MEMBRANEF 2000 – F 3000P 3000 – P 4000

ALM 3000 – ALM 4000

DESCRIPTIONThese are plastomeric type waterproofing bituminous membranes which are re-sistant to heat shocks in hot and cold climates, APP (Thermoplastic resin Atactic Polypropylene) added to increase bituminous strength, produced with fiber glass carrier or polyester felt carrier to increase the mechanical strength.

APPLICATION AREASThey are used in all kinds of structures that require waterproofing such as foundati-ons, underground shear walls, balconies, terraces, wet volume areas, roofs, bridges, highways.

FEATURESThese membranes can be applied on all kinds of surfaces and they provide very good adhesion. Thanks to elasticity in stress and strain conditions they withstand to buil-ding movements. They are easy to apply with a torch. If proper product selection and application is achieved and adequate protection is provided, they will have life span equivalent to life of the building.

Thickness Total m2

F 2000 2mm 15m2

F 3000 3mm 10m2

P 3000 3mm 10m2

P 4000 4mm 10m2

ALM 3000 3mm 10m2

ARD 4000 4mm 10m2

SURFACE PREPARATION AND IMPLEMENTATIONApplication surface should be cleaned from the substances which would prevent adhesion such as form oil, dust, paint, dirt, etc. The cracks and holes on the surfa-ce should be covered with Fixkim repair mortars. Fixkim Bitumen Primer should be applied to the surface with brush or roller without being diluted. The appropriate membrane is adhered on the primed surface with the help of torch by fully adheren-ce method (Adhesion from joints only is recommended in the first layer of membrane application on the lean concrete in base insulation implements only). The joints must be welded resplendently. The joints of the membranes must be overlapped min. 10 cm. For the 2nd layer application over the first layer, joints must not be overlapped with the first layer’s joints, that is to say, the overlapping sections should be app-lied in a staggered manner and each layer should be applied parallel to each other. Non-slaty overlapping in slaty membranes should be overlapped. The membranes should be applied perpendicular to the direction of flow of the water and the appli-cation should be made from the bottom upwards. The membranes other than slated membranes and aluminum foil coated membranes must be protected from the outer effects after they have been applied.

STORAGEIt should be stored in closed environments not exposed to the direct sunlight, on a flat ground, at the temperatures over +5 oC in upward position and another product should not be placed on it.

FIXKIM MEMBRANEF 2000 – F 3000 / P 3000 – P 4000 /

ALM 3000 – ARD 4000

154

POLYESTER FELT CARRIERS / PLASTOMER BASEDTENSILE STRENGTH LONGITUDINAL N/5CM 800 MINIMUMTENSILE STRENGTH CROSS N/5CM 600 MINIMUMBREAKING ELONGATION LONGITUDINAL -N/5CM 35% MINIMUMBREAKING ELONGATION CROSS -N/5CM 35% MINIMUMBENDING IN COLD -10 0C MINIMUMTEMPERATURE RESISTANCE 120 0C MINIMUMDIMENSIONAL STABILITY 0.6% MAXIMUM

TECHNICAL SPECIFICATIONS

FIBERGLASS CARRIERS / PLASTOMER BASEDTENSILE STRENGTH LONGITUDINAL -N/5CM 400 MINIMUMTENSILE STRENGTH CROSS -N/5CM 300 MINIMUMBREAKING ELONGATION LONGITUDINAL N/5CM 2% MINIMUMBREAKING ELONGATION CROSS N/5CM 2% MINIMUMBENDING IN COLD -10 0C MINIMUMTEMPERATURE RESISTANCE 120 0C MINIMUMDIMENSIONAL STABILITY 0.6% MAXIMUM

Thickness Total m2

F 2000 2mm 15m2

F 3000 3mm 10m2

P 3000 3mm 10m2

P 4000 4mm 10m2

ALM 3000 3mm 10m2

ARD 4000 4mm 10m2

155

POWERMIX MEMBRANEF 2000 – F 3000 / P 3000 – P 4000 /

ALM 3000 – ALM 4000

DESCRIPTIONThese are plastomeric type waterproofing bituminous membranes which are re-sistant to heat shocks in hot and cold climates, APP (Thermoplastic resin Atactic Polypropylene) added to increase bituminous strength, produced with fiber glass carrier or polyester felt carrier to increase the mechanical strength.

APPLICATION AREASThey are used in all kinds of structures that require waterproofing such as foundati-ons, underground shear walls, balconies, terraces, wet volume areas, roofs, bridges, highways.

FEATURESThese membranes can be applied on all kinds of surfaces and they provide very good adhesion. Thanks to elasticity in stress and strain conditions they withstand to buil-ding movements. They are easy to apply with a torch. If proper product selection and application is achieved and adequate protection is provided, they will have life span equivalent to life of the building.

SURFACE PREPARATION AND IMPLEMENTATIONApplication surface should be cleaned from the substances which would prevent adhesion such as form oil, dust, paint, dirt, etc. The cracks and holes on the surfa-ce should be covered with Fixkim repair mortars. Fixkim Bitumen Primer should be applied to the surface with brush or roller without being diluted. The appropriate membrane is adhered on the primed surface with the help of torch by fully adheren-ce method (Adhesion from joints only is recommended in the first layer of membrane application on the lean concrete in base insulation implements only). The joints must be welded resplendently. The joints of the membranes must be overlapped min. 10 cm. For the 2nd layer application over the first layer, joints must not be overlapped with the first layer’s joints, that is to say, the overlapping sections should be app-lied in a staggered manner and each layer should be applied parallel to each other. Non-slaty overlapping in slaty membranes should be overlapped. The membranes should be applied perpendicular to the direction of flow of the water and the appli-cation should be made from the bottom upwards. The membranes other than slated membranes and aluminum foil coated membranes must be protected from the outer effects after they have been applied.

STORAGEIt should be stored in closed environments not exposed to the direct sunlight, on a flat ground, at the temperatures over +5 oC in upward position and another product should not be placed on it.

POLYESTER FELT CARRIERS / PLASTOMER BASEDTENSILE STRENGTH LONGITUDINAL N/5CM 600 MINIMUMTENSILE STRENGTH CROSS N/5CM 400 MINIMUMBREAKING ELONGATION LONGITUDINAL -N/5CM 30% MINIMUMBREAKING ELONGATION CROSS -N/5CM 30% MINIMUMBENDING IN COLD -5 0C MINIMUMTEMPERATURE RESISTANCE 110 0C MINIMUMDIMENSIONAL STABILITY 0.6% MAXIMUM

TECHNICAL SPECIFICATIONS

FIBERGLASS CARRIERS / PLASTOMER BASEDTENSILE STRENGTH LONGITUDINAL N/5CM 300 MINIMUMTENSILE STRENGTH CROSS N/5CM 200 MINIMUMBREAKING ELONGATION LONGITUDINAL N/5CM 2% MINIMUMBREAKING ELONGATION CROSS N/5CM 2% MINIMUMBENDING IN COLD -5 0C MINIMUMTEMPERATURE RESISTANCE 110 0C MINIMUMDIMENSIONAL STABILITY 0.6% MAXIMUM

catalogo portafolio fixkim

Documents

anchorage mortar

sheet adhesive mortar

marble adhesive mortar

fixing mortar

jamb adhesive mortar

flex ceramic adhesive

flex joint filling mortar

tile ceramic adhesive