building sturdy sawhorses

7/30/2019 Building Sturdy Sawhorses

http://slidepdf.com/reader/full/building-sturdy-sawhorses 1/6

Building Sturdy Sawhorsesby Patrick McCombe I once had a coworker who described his favorite sawhorses as Clydesdales. It was an appropriate name sincehis bulletproof horses seemed as heavy as their 1000-lb. namesake.Another coworker had the opposite approach. He favored lightweight sawhorses made from six equal-length

pieces of 2x4. He could bang a pair together in the time it takes to roll out an extension cord.

I think the best sawhorses are a combination of these two approaches. The best design I’ve found is the easy-to-build “Stackable site-built sawhorses” from Ty Simmons of Fort Laramie, Wyo.

I like Ty’s horses because they’re lightweight and strong, and use common materials.

You could build them with only a circular saw, but using a tablesaw for beveling the top and a sliding miter sawfor cutting the legs makes the process much easier.Including setup, it took me about 90 minutes and cost me $50 in materials to make the pair of horses featuredhere.

1. Cut the legs.

http://www.finehomebuilding.com/authors/patrick-mccombe.aspx



http://www.finehomebuilding.com/how-to/reader-tip/stackable-site-built-sawhorses.aspx



http://www.finehomebuilding.com/CMS/uploadedimages/Fine_Homebuilding/Articles/218/021218088-4_xlg.jpg






Photo by: Ed Pirnik

All legs have a compound angle on both ends. With the miter and bevel both set at 17°, cut four legs (for a pairof horses) so that the finished leg has the same cut on both ends. Leaving the bevel setting alone, rotate themiter table to the other 17° mark on the other side of 90°, and cut the other four legs.

2. Bevel the top.

Rip a 17° bevel on both sides of the top. You can do this with a circular saw, but a tablesaw with a rip fence isfaster and easier.

3. Fasten the legs.Mark the top 3 in. from the end at all four corners. Hold the leg flush to the top, and drill the pilot holes with atwist or pilot/countersink bit. Then drive the screws. Use 11/2-in. #10 wood screws because they have greatershear strength than deck or drywall screws. Trim one of the tops later if you want the horses to stack.





4. Install the bracing.Mark the legs 12 in. up to locate the 1x4 leg bracing. Hold or clamp the board in place, and scribe both ends to

match the leg angle. Drill the pilot holes, and drive the screws.






5. Scribe and cut the gussets.

Clamp or hold the gusset in place while you drill pilot holes. Be sure to align the drill bit carefully so that the holestays in the center of the leg. After you run in the screws, your team of horses is ready for work.

6. Almost done.






Clamp or hold the gusset in place while you drill pilot holes. Be sure to align the drill bit carefully so that the holestays in the center of the leg. After you run in the screws, your team of horses is ready for work.

Four more optionsConsider these alternatives when space is tight or time is short.

Site-built

Space Saver Built from 20-in. by 32-in. scraps of 3/4-in. plywood, these clever

knockdown sawhorses are surprisingly sturdy. The 3/8-in.-deep mortises in the 2x6 top are made with a circular saw and a sharpchisel.

Get ‘er done Made from six 32-in. pieces of 2x4, these are the horses to build

when you’re in a hurry. You can use gun nails if time is extra tight, but 21/2-in. screws hold better and come apart easier when it’stime for your steeds to become blocking.

Store-bought





Fast, rock solid, but expensive Trojan’s nearly indestructible TS series is the

best commercially produced sawhorse, but you’ll need to shell out $90 per pair for the 27-in. version. The 35-in. model costsanother $12 per pair.

A popular option Available at home centers everywhere, these sawhorses ($60

per pair) have selfleveling, adjustable legs that keep the horse steady on uneven terrain, but it’s easy to lose the leg extensionsand the bolts that secure them.

Photos by Rob Yagid, exept where noted.



building sturdy sawhorses

Documents