back up light kit - s3-us-west-2.amazonaws.com · 1. choose a location for your rigid industries...
TRANSCRIPT
back up light kitSR-Q® / sr-Q® flush mount (fm)
Back up Light kit
installation instructions
warranty information
kit includes
®
2 - Rigid Industries SR-Q/SR-Q Flush Mount (FM) LED Lights1 - Custom Back-up Kit Wiring Harness2 - Stainless Steel (18-8) ¼” x 1.5” Socket Head Cap Screws2 - Stainless Steel (18-8) Lock Washers
2 - Stainless Steel (18-8) Mounting Brackets2 - Stainless Steel (18-8) Carriage Bolts2 - Stainless Steel (18-8) ¼” Nylon Insert Lock Nuts2 - Stainless Steel (18-8) Standard Nuts
Warranty Periods: • All LED Light bars – Limited Lifetime • Accessories and Mounts – 2 years
Warranty Coverage: To begin your warranty claim, you must have a Return Merchandise Authorization (RMA) number. To get your RMA number, please contact our warranty department by phone at 480-655-0100 ext. 1008, or by �lling out the Return Merchandise Authorization Form on our website.
All of the following will immediately void all warranties:• Customer negligence – The customer has modi�ed the light and/or is not using it for the recommend application. • Customer abuse – Damage to the light beyond normal wear and tear. • Repair work done by unauthorized personnel without Rigid Industries’ approval.• If the light has been opened or any screws have been removed.
All warranties are non-transferable. Warranty terms and policies are subject to change without notice.
*For all information regarding the Rigid Industries’ Limited Lifetime Warranty please call 855-760-5337 ext. 1008, email [email protected], or visit our warranty page online at RigidIndustries.com/about/warranty.
• Flashlights – 1 year • Batteries – 90 days
Rigid Industries warrants that this product will be free from defects in material and workmanship. If you believe your Rigid Industries product is defective, it must be returned to Rigid Industries for inspection by our warranty claims department. If, after inspection, Rigid Industries veri�es that the defect was not caused by negligence, abuse, unauthorized repair or disassembly, Rigid Industries will determine whether the product will be repaired or replaced in accordance with Rigid Industries Limited Lifetime Warranty*.
779 N Colorado St, Gilbert, AZ 85233 • 855-760-5337 ext 1008 • www.rigidindustries.com
Follow us on facebook at
facebook.com/RigidIndustries
IS-98002 REV 3
Your installation is now complete.
Welcome to the Rigid Nation!
SR-Q and Rigid Industries are registered and/or common law marks owned by JST Performance, Inc. d/b/a Rigid Industries.
Always disconnect any power sources connected to yourvehicle before servicing fuses or electrical system.
installation instructions
1. Choose a location for your Rigid Industries back-up lights. Make sure you have clearance for the lights to adjust/rotate without interference and a path for wiring. Mark & drill holes. Secure lights on provided brackets with provided hardware.
2. Route wire harness completely before connecting anything. Once you have run the harness in place and planned your hard attachment locations and zip tie locations, proceed with install. Use the diagram below and the following notes…
3. Once the wire harness has been fully installed, you are ready to test out your lights. Middle position on your switch is “o�”. Down position is “on when in reverse” and Up position is “always on”.
a. Relay should be mounted under dashboard.
b. Switch should be mounted on driver side dashboard. Drill a ¾” diameter hole and feed switch through from the back side.
c. If you would like your switch to be illuminated when your kit is in use, connect the black wire to pin 2b on the switch. If you do not wish for your switch to illuminate, simply omit this step.
d. The connector between the relay and in-line fuse is there to prevent you from having to get the switch/relay or fuse holder through the �re wall. Drill a small hole or use an existing ingress. Push black battery line through from vehicle cab. Push the red battery line through from the engine compartment then connect with the in-line connector.
e. Red battery connector should be attached to the positive battery terminal. Black battery connector may be connected to negative battery terminal or any suitable ground.
f. Reverse light lead must be connected to the factory reverse light line. The lead is long enough to connect at the factory reverse lights – or you can tie in under the dash if you prefer.
g. Path for wiring between the relay and the lights is up to you. Take care to avoid heat sources, sharp edges or abrasive surfaces. Secure wiring in place with plenty of zip ties.
h. Deutsch connectors should connect to your two Rigid Industries lights.
60A Relay: Mount under dashboard.
Sealed Deutsch Connectors: Attach to lights.
Reverse Light Line: Connect to factory reverse light lead.
15A In-line Fuse: Free under hood.
Battery Connectors: Connect to battery.
Switch: Mount in cab.
Red - 1a
Blue – 2a
White – 3a
Black – 2b
wi
Connector: Free under hood.
Reverse Light Line: Connect to
1a2a3a2b
Mo
un
tin
g T
em
pl
at
e
5.8 in or 14.7 cm
5.25 in or 13.3 cm
2.07 in or 5.27 cm
* If printing from a printer, choose AC
TUA
L SIZE print option*