EUROPEAN SYSTEMS GUIDE

Awlgrip® North America1 East Water Street

Waukegan, Illinois 60085 TEL: 847.599.6212 FAX: 847.599.6209

www.awlgrip.com

Awlgrip® EuropeBannerlaan 54

2280 Grobbendonk Belgium

TEL: 32.14.25.7770 FAX: 32.14.23.0880

Awlgrip® Australia76 Waterway Drive Coomera

Queensland 4209 Australia

TEL: 61.7.5573.9600 or 1800.007.866

FAX: 61.7.5573.9677

Awlgrip® New Zealand686 Rosebank RoadAvondale, Auckland

New Zealand TEL: 64.9.828.3009

or 0800.150.527 FAX: 64.9.828.1129

Volume 3

Awlgrip® AsiaAsia International Pte. Ltd.449 Tagore Industrial Avenue

01-03 Hong Joo Industrial Building Singapore

787820 TEL: 65.6453.1981 FAX: 65.6453.1778

TOPCOATS - AWLGRIP® & AWLCRAFT® 2000

TOPCOATS - AWL®GARD (INTERIOR ONLY)

BBEEYYOONNDD JJUUSSTT GGOOOODD LLOOOOKKIINNGGAWLGRIP manufactures two different types ofresin bases for urethane topcoats. AWLGRIPis a polyester urethane, and AWLCRAFT 2000is an acrylic urethane. Aside from theobvious, one uses polyester resin and oneuses acrylic resin. The difference betweenthe two is molecular size.

Polyester molecules are much smaller thanacrylic molecules. A given volume of polyester resin contains many more molecules than the same volume of acrylicresin. Thus the polyester has more reactionsights than the acrylic. When both are fullycrosslinked, the polyester forms a tighter,tougher film. The more dense crosslinking provides a harder, more abrasion resistantfilm, with better chemical resistance than theacrylic film.

High crosslink density yields better chemicaland abrasion resistance. It also yields a rigidfilm. In today’s marketplace there is a need for both acrylic and polyester urethane technology. Both resins will resist staining and provide long lasting gloss.

Application characteristics, chemical andstain resistance, repairability, and cure timesall need to be considered when choosing a urethane.

HHOOWW TTHHEEYY WWOORRKKCrosslinked, two component polyurethanesdry when the solvent evaporates. Then theycure as the components react to form the urethane molecule. The more crosslinks, themore durable the final finish. Keep in mind alonger cure time is needed for the coatingsto reach this durable, final finish.

Coatings with a relatively long cure time allowthe pigments to migrate toward thesubstrate. A resin-rich wear layer forms,much like the clear urethane film on a “nowax” floor.

This resin-rich layer provides long term protection for the pigment particles, improvescolour and gloss retention and provides thedeep gloss associated with high qualityurethanes.

TTHHEERREE’’SS AA SSYYSSTTEEMMAATTIICC AAPPPPRROOAACCHHBe cautioned however! Choose the topcoatyou require for your project first, then investigate the primer system to support thetopcoat performance. AWLGRIP offers a complete line of chemically compatibleprimers, fairing compounds and surfacers to support its topcoats.

Do not mix any components, other thanthose manufactured by AWLGRIP, into theAWLGRIP system.

AWLGRIP provides detailed instructions forcare and maintenance of topcoats. Includingmild but effective products such asAWLWASH and AWLCARE to help maintain thehigh gloss urethane topcoats.

This in fact is the AWLGRIP coating advantage –performance delivered through a complete coating system.

TTHHIISS IISS AA PPRROOFFEESSSSIIOONNAALL UUSSEE PPRROODDUUCCTT..

AWLGRIP develops and manufactures different types of urethane topcoats –AWLGRIP and AWLCRAFT 2000 – which are used in the yacht market. Each topcoat has its ownspecial features to meet the criteria for a specific project. Some of the special features for eachtopcoat are listed to help with your decision. AWLGRIP and AWLCRAFT 2000 topcoats can beused on wood, fibreglass, aluminium and steel. The best results can be achieved by following AWLGRIP’s recommendation of a complete system.

AWLGARD Interior Urethane is designed for use where a durable urethane is required and the application of a solvent borne coating isimpractical. Typical applications include engine rooms, lazarettes,showers and bulkheads. This two-component urethane has excellentsolvent resistance to denatured alcohol and acetone, as well as dieselfuel and anti-freeze.

The water reducible technology provides a product with low odour anda flash point greater than 200˚F/93˚C. Painters rave about thedesirable application characteristics including quick tack times,extended pot life, and superior flow and levelling. AWLGARD InteriorUrethane has excellent gloss retention, heat resistance to180˚F/82˚C, shelf stability, and superior hiding characteristics.

The standard colours for AWLGARD include Matterhorn White (W8201),Cloud White (W8202) & Snow White (W8203),

All colours can be applied by spray, brush, or roller. Mix ratio is 3 partscolour base to 1 part converter (W3201) to 1 part reducer (T0149). All three components are sold as a five-quart kit.

Polyester Urethane Topcoat

Acrylic Urethane Topcoat

Interior Urethane Topcoat

• Premium acrylic urethane topcoat.

• Superior flow-out and high gloss.

• Ease of application.

• Fast drying to reduce dust entrapment.

• For spray application only.

• For use above the waterline only.

• Custom colours available.

• High performance urethane topcoat systems.

• Recognised world-wide for 30 years.

• Full product range of coating systems for all substrates.

• Can be applied by spray or brush/roll.

• For use above the waterline only.

• Excellent colour retention and chemical resistance.

• Custom colours available.

SYSTEMS ABOVE THE WATERLINE

Awlgrip®, Awl® and all products mentioned in this brochure are trademarks of, or licensed to, Akzo Nobel. © Akzo Nobel 2006

Awlgrip® Europe: Bannerlaan 54, 2280 Grobbendonk, Belgium. TEL: 32.14.25.7770 FAX: 32.14.23.0880.

All representations and statements concerning the product(s) in this brochure are accurate to the best of our knowledge. Statements made in this brochure are advisory only and are not intendedto be specific recommendations or warranties of any product, combination of products or fitness for any particular purpose. To the extent permitted by law, we do not accept any liability to anyperson for any loss or damage (direct or indirect) that may arise from any use of or reliance on any of the methods or information contained in the brochure for any purpose.

Unless otherwise agreed in writing, all products supplied and technical advice or recommendations given are advisory only and subject to the Conditions of Sale of our supplying company. Anywarranties, if given, are contained in those standard Conditions of Sale and are the only ones made with respect to any products we sell to you or advice or recommendations we give to you.

For each of our products the relevant Product Data Sheet, Material Safety Data Sheet and package labelling comprise an integral information system about the product in question. Copies of our Product Data Sheets and Material Safety Data Sheets are available on request or from our Website: www.awlgrip.com

Clean, sand, grind or blast (as necessary).

Apply AWL®FAIR L.W.*

Apply Hullgard or 545 Epoxy Primer

Apply 545 Epoxy Primer for spray application

Apply Ultra Build or Standard E Fairing Compound*

Apply AWLGRIP® or AWLCRAFT® 2000 TopcoatTopcoats

Finish Primers

Epoxy Surfacers

Epoxy Fairing Compound

Substrate Sealer

Prepare Substrate

Details for application, preparation, and mixing of the above steps can be found in the Awlgrip Application Guide or on the website: www.awlgrip.com

* Note: Custom made systems with alternative Awlgrip® products like Sprayable Fairing Compound, Awl®Quik and High Build are available on request

Clean, sand, grind or blast (as necessary).

Apply AWLFAIR L.W.*

Apply Hullgard or 545 Epoxy Primer

Apply 545 Epoxy Primer for spray application

Apply Ultra Build or Standard E Fairing Compound*

Apply AWLGRIP® or AWLCRAFT® 2000 TopcoatTopcoats

Finish Primers

Epoxy Surfacers

Epoxy Fairing Compound

Substrate Sealer

Prepare Substrate

Details for application, preparation, and mixing of the above steps can be found in the Awlgrip Application Guide or on the website: www.awlgrip.com

FIBREGLASS, GELCOAT, COMPOSITE, & WOOD

ALUMINIUM & STEEL

BRIGHTWORK AND VARNISH

TOPCOAT CARE

An effective detergent for cleaning, yet still gentle enough for frequent use on AWLGRIP® and AWLCRAFT® 2000. AWLWASH has been extensively tested in AWLGRIP’s laboratories and in the harsh yacht environment.

Wash Down Concentrate -73234

AWLGRIP developed AWLCARE for customers who want to protect their painted finish and need the additional cleaning power of a hand applied product. AWLCARE will help temporarily seal and restore shine to painted surfaces that have become porous due to age or mistreatment. Once a painted surface becomes porous it allows dirt to collect on the surface making the normal washing process more difficult. Regular applications of AWLCARE will help seal the porosity, helping to maintain a satisfactory appearance until there is time to repaint.

• AWLCARE contains no harsh abrasives and will not scratch the painted surface. • AWLCARE leaves a non-yellowing, protective polymer coating which lasts through multiple washings.• AWLCARE removes mild stains such as water spots and diesel soot and with regular applications, increases resistance to

attack from acid rain and other environmental pollutants.

Protective Polymer Sealer – 73240

Classic Spar Varnish - M3131 / T0016

High Solids Marine Varnish - M3146 / T0180H.S.

• Non-Skid additive for use with AWLGRIP or AWLCRAFT 2000.• GRIPTEX is a white, round, polymer bead which can be added to

any topcoat colour. • GRIPTEX is the non-skid additive chosen by major yachts and boat

builders around the world.• GRIPTEX is designed for use on previously painted non-skid areas,

smooth decks that require non-skid protection, and fibreglass deckswith gelcoat non-skid pattern.

Two systems are available to meet varying application and performance requirements.

Traditional Varnish System – AWLSPAR Classic Spar Varnish andAWLSPAR H.S. Marine VarnishThese are traditional phenolic, tung oil varnisheswith UV inhibitors and absorbers. AWLSPAR andAWLSPAR H.S. are the perfect products for the traditionalist who wants easy to apply, easy torepair products and doesn’t object to regularmaintenance coats.

Ultimate Brightwork System – AWLSPAR/AWLSPAR H.S./AWLBRITEThis system combines the colour highlights ofAWLSPAR® varnishes to provide a traditional look,with the durability of AWLBRITE Clear in a fastrecoat, relatively easy to repair combination of varnish and urethane coatings. The ULTIMATE BRIGHTWORK SYSTEM can be applied in seven to ten days. AWLGRIP recommends the UltimateBrightwork System where the longest lasting,most durable system is desired.

• GRIPTEX non-skid can be applied by two methods.1. By using the Broadcast or Shaker Method where the GRIPTEX is

sprinkled onto a still tacky application of a AWLGRIP Topcoat.2. By adding GRIPTEX to properly mixed and reduced topcoat and

spray apply with a siphon gun or pressure pot with an agitator.

• GRIPTEX is available in three grit textures: Fine (73012), Coarse(73013) and Extra Coarse (73237) which are available in Quarts.These different grits can also be mixed together to create a customnon-skid texture.

NON-SKID

Clear Acrylic Urethane Brightwork Protection - J3005 / J3006 /A0031

• Unique combination of light fast resins, ultraviolet inhibitors and absorbers.

• Provides a tough, long lasting, high gloss finish.• Excellent durability.• Reduces maintenance.

• Excellent flow characteristics.• Fast dry, fast recoat for quick

build up and maintenance.• For application by brush only.• Compatible with AWLSPAR varnishes.

• Formulated to recreate the highest quality classic spar varnishwith state of the art ultraviolet inhibitors and absorbers.

• Excellent durability.• Fast dry, fast recoat for quick build up.

• Excellent application by brush.• For use above the waterline only.• Superior base for AWLBRITE urethane.

(See Ultimate Brightwork System)

• AWLWASH does not contain alkalies, acids, or abrasives, and is free rinsing, which decreases drying time.• AWLWASH is 100% biodegradable and comes in a refillable, “Tip ‘N Measure” container, which makes it easy to get the

proper mix ratio: One ounce of AWLWASH per gallon of water.

• More build per coat with maximum gloss and durability when compared to conventional varnish.

• Higher in solids and less solvent (VOC: 2.38lbs/gal – 285g/lt) than classic spar varnish.

• Excellent application characteristics by brush or spray.

• Can be overcoated with AWLBRITE in as little as 7 days.(See Ultimate Brightwork System)

• For use above the waterline only.• Formulated with state of the art

ultraviolet inhibitors and absorbers.

BOTTOM SYSTEMS

Bottom PrimersHullgard Extra D6120/D3730 is a two-component epoxy substrate primer suitable as a first coat on fibreglass, steel,aluminium and wood. Hullgard Extra must be overcoated with Hullgard Epoxy Primer D6070/D3707 when appliedbelow the waterline.

Hullgard Epoxy Primer D6070/D3707 is a two-component build primer that serves to protect against corrosion andosmosis.*** In below water systems it may be used as the only primer or over Hullgard Extra D6120/D3730.Hullgard Epoxy Primer is the ideal primer for subsequent application of Awlstar Gold Label or Awlstar Aluminum LabelAntifouling.

Awlstar Aluminum Label is, as the name implies, an antifouling that is suitable for primed and preparedaluminium hulls. Awlstar Aluminum Label is a slow polishing formulation that delivers excellent foulingprotection through controlled release of biocides from the film. Its slightly harder film makes it very suitablefor all crafts, including faster vessels.

Awlstar Aluminum Label is recommended for fibreglass, steel, aluminium and wood. It’s also our onlyantifouling that has a bright white offering.

Awlstar Aluminum Label is available infull 1 gallon units. The product isdesigned to be applied over HullgardEpoxy Primer D6070/D3707.

Awlgrip Europe has introduced a new and updated version of Awlstar Gold Label. It is still based on aneroding resin matrix, but it has been updated with a new anti-foul booster package which brings it up tospeed with modern day boating.

The new formulation of Gold Label has allowed for cleaner, better colours to be formulated whilst flow andhold up have been improved. The product is now also available in a full gallon unit and 15lt packs.*

Awlstar Gold Label is to be applied professionally and is available to most boat yards in Europe**. Theproduct is recommended for fibreglass, steel and wood substrates. Do not use on aluminium.

Awlstar Gold Label is designed to be applied over Hullgard Epoxy Primer D6070/D3707. It is also fullycompatible with Awlstar Aluminum Label.

Charcoal BlackBP204

Medium GreenBP403

Light BlueBP508

RedBP705

White LightningBP809

PLEASE NOTE: Colour chips may vary from actual product due to printing process.

Gold Label Antifouling

Deep BlueBP507

BlueBP523

Black BP222

WhiteBP823

Aluminum Label Antifouling

* Gold Label green is available in 1gl units only ** For registration details contact Awlgrip Europe *** When applied at the recommended film thickness

NewFormulation

HULLGARD - D6070/D3707 Buff(Apply multiple coats.)

AWL®STAR Antifouling(Apply multiple coats.)

HULLGARD EPOXY PRIMERD6070/D3707 Buff

(Apply multiple coats.)

HULLGARD EXTRA Off White D6120/D3730

AWL®STAR Antifouling(Apply multiple coats.)

SYSTEM 1:

SYSTEM 2:

PRODUCT CHECK LIST

AWL®PREP Surface Cleaner.....................................................T0008Surface Degreaser/ Cleaner T0340 .........................................T0340

CLEANINGAWLGRIP® Spray Base . . . . . . . . . . . . . . .(Selected from Colour Card - G or H Code #)Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AWL-CAT #2 (G3010)Reducer . . . . . . . . . . . . . . . . . . . . . . . . . .T0003 or T0001 or T0002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AWLGRIP® BrushBase . . . . . . . . . . . . . . .(Selected from Colour Card - G or H Code #)Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AWL-CAT #3 (H3002)Reducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T0031

AWLCRAFT® 2000 SprayBase . . . . . . . . . . . . . . . . . . .(Selected from Colour Card - F Code #)Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AWL-CAT #2 (G3010)Reducer . . . . . . . . . . . . . . . . . . . . . . . . . .T0003 or T0001 or T0002

TOPCOATS

TOPCOAT - INTERIOR

ANTIFOULING

BOTTOM PRIMERS

AWLWASH® - Wash Down Concentrate .....................................73234AWLCARE® - Protective Polymer Sealer.....................................73240

MAINTENANCE PRODUCTS

GRIPTEX - Fine Grit Non-Skid Additive ......................................73012GRIPTEX - Coarse Grit Non-Skid Additive ..................................73013GRIPTEX - Extra Coarse Grit Non-Skid Additive..........................73237Premium Tack Rags ...............................................................73009PRO-CURE X-98 Fast Accelerator .............................................73014PRO-CURE X-138 Inhibited Accelerator.....................................73015Flattening Agent for Urethane Topcoats...................................G3013CRATER-X Anti-cratering Solution ............................................M1017COLD CURE™ 545 Primer Accelerator ....................................M3066

AUXILIARY PRODUCTS

30-Y-94 Non-Sanding, Mil-Spec Anti-Corrosive Epoxy PrimerBase.....................................................................................S9001Converter ..............................................................................S3001

545 Epoxy PrimersBase - Gray ...........................................................................D1001Base - White .........................................................................D8001Converter ..............................................................................D3001

HULLGARD Extra PrimerBase - Off White ....................................................................D6120Converter ..............................................................................D3730

AWL®QUIK Fast Recoat Spray or Brush Sanding SurfacerBase - Pale Yellow .................................................................D8003Converter ..............................................................................D9001

QUIK-GRIP Fast Dry Non-Sanding PrimerBase - White .........................................................................D8016Converter ..............................................................................D3040

PRIMERS – SEALERS

AWL®FAIR L.W. Epoxy Trowelable Fairing CompoundBase - White .............................................................................D8020Converter - Red .........................................................................D7007Converter - Red Fast ..................................................................D7010

Epoxy Sprayable Fairing CompoundBase - Tan .............................................................................D6001Converter ..............................................................................D3011

Ultra Build Epoxy PrimerBase - White..........................................................................D8008Converter ..............................................................................D3018

High Build Epoxy PrimerBase - Off White ....................................................................D8002Converter ..............................................................................D3002

FAIRING – SURFACING

Standard - Spray .....................................................................T0006Slow - Brush Only (545 Epoxy Primer & AWL-QUIK) ....................T0031 ULTRA-BUILD ..........................................................................T0073

AWLGRIP® & AWLCRAFT® 2000–TOPCOAT REDUCERSFast .......................................................................................T0001Very Fast................................................................................T0002Medium .................................................................................T0003Slow-Hot Weather Retarder......................................................T0005Brushing/Slow........................................................................T0031

PRIMER REDUCERS

AWLGARD (Base colour, converter and reducer are sold as five quart kit only.)

Matterhorn White ...................................................................W8201Cloud White...........................................................................W8202Snow White ...........................................................................W8203

AWLSTAR Gold Label AntifoulingWhite Lightning ..........................................................................BP809Charcoal Black...........................................................................BP204Medium Green ...........................................................................BP403Light Blue ..................................................................................BP508Deep Blue..................................................................................BP507Red ...........................................................................................BP705Reducer .....................................................................................T0101

AWLSTAR Aluminum Label AntifoulingWhite ........................................................................................BP823Black.........................................................................................BP222Blue ..........................................................................................BP523Reducer .....................................................................................T0101

AWL®BRITE Clear Urethane for BrightworkBase ......................................................................................J3005Converter................................................................................J3006Activator.................................................................................A0031

AWLSPAR Classic Spar VarnishBase .....................................................................................M3131Reducer .................................................................................T0016

AWLSPAR H.S. High Solids Marine VarnishBase .....................................................................................M3146Reducer .................................................................................T0180

BRIGHTWORK AND VARNISH

HULLGARD Epoxy PrimerBase .........................................................................................D6070Converter...................................................................................D3707

2006