Washing machineUser Guide

AWF 60 MD

Product Information

It is important to keep this manual in a safe place (for your record).

Date of purchase ____________________ Purchaser __________________________

Dealer/Retailer ______________________ Branch/Location _____________________

Suburb____________________________ Town/City __________________________

Country ______________________________________________________________

Model No. _________________________ Serial No. __________________________

N.B. To find information on model numbers and serial numbers, look behind the washing machine door.

AWF 60 MD

Contents

1 Technical features Page 3

2 General recommendations Page 4

3 Installation instructions Page 5

4 Before the first wash cycle Page 9

5 Preparing the wash Page 9

6 Detergent and additives Page 10

7 Page 14Program selection and washingmachine operation

8 Page 19Care and maintenance

9 Page 21Before calling for service

6

85

60

54

73

240/50

10

2400

52

1000

Maximum capacity (kg.)

Height (cm.)

Width (cm.)

Depth (cm.)

Net weight (kg.)

Power requirement (V/Hz)

Nominal current (A)

Power (W)

Washing speed (rpm)

Spin speed (rpm)

The appearance and specifications are subject to changewithout notice.The graphics shown in the manual are schematic and maynot conform exactly with your washing machine.

1 Technical features

Top lid

Detergent Dispenser

Control panel

Front door

Filter cover

3

• The appliance is not intended for use by young children or infirmed persons without supervision

• Young children should be supervised to ensure that they do not play with the appliance or they do not climb into the drum(see also the following page chapter “Child Safety”)

• Do not leave the washing turned on when not in use

• Before any cleaning and maintenance switch off the machine or disconnect it from the mains

• Clean the outside of the washing machine with a damp cloth. Do not use abrasive detergents

• Never open the door forcibly or use it as a step

• If necessary, the power cable may be replaced with an identical one obtained from an Authorised Service Center. The powercable must only be replaced by a qualified technician

2 General recommendations

4

3 Installation instructions

5

1. Remove the packaging

• After unpacking, make sure that the washing machine is undamaged. If in doubt, do not use the washing machine. Contactan Authorised Service Centre or your local retailer• Check that the accessories and supplied parts are all present• Keep the packing material (plastic bags, polystyrene parts, etc.) out of reach of children, as they arepotentially dangerous

2. Remove the transit bolts

• The washing machine is fitted with a transit bolts to avoid any possible damage to the interior during transit. Before usingthe washing machine, it is imperative that the transit bolts are removed

Removing transit safety bolts at the rear of the machine

Attention!Please keep the safety bolts for future transportation and reinstate them before transporting your machine. Nevertransit your machine without the transit bolts in position.Never place your machine on a carpet. This prevents air circulation. The electrical components of the machinemay overheat and may cause damage.

The transit safety bolts must be removed before any operation of the machine. Bolt heads, marked “C” should be turned in aanti clockwise direction until the bolt can be partially withdrawn.

Remove transit safety bolts and rubber bushes by pulling outwards. (an up/down action and a small squirt of washing upliquid should ease removal.)

Plastic plugs, supplied inside the protective bag and designated as “P”, should be placed in the safety bolt holes accordingto the direction shown.

6

Water Supply• Hot water temperature should not exceed 75˚C. Temperatures above this may the machine to fault orcause damage to the machine• If you have an uncontrolled water heating source (eg a wet-back or solar heating system) you shouldfit a Safe Valve. This will ensure the hot water temperature remains within safe limits.• Inlet water pressure: Maximum 1 MPa (150 psi), Minimum 34 Pa (5 psi)• Inlet water flow rate: Minimum 3 litres/minute

Inlet Hoses1) Connect the straight ends of the inlet hoses to the taps. There are washers fitted in both ends.2) Connect the elbow ends of the inlet hoses to the inlet valves on the back of the machine. The cold inletvalve is marked in blue, while the hot inlet valve is marked in red.

Cold Supply Only:If you only have a cold water supply, an inlet valve cap (blanking cap) MUST be connected to the hot inletvalve. The cap prevents water leaking out of the hot inlet valve. The cap is supplied in the same bag asthe inlet water hoses.

4. Adjust feetIn order for quiet and stable operation, the machine should be placed properly and levelled on its feet.Your machine comes with two adjustable feet. If the machine is unstable, loosen the plastic counternutand screw or unscrew the adjustable foot until the machine is levelled perfectly. After positioning, tightenthe counternut for stability.

7

3. Position the washing machine• Move the appliance without lifting it by the worktop• Install the appliance on a solid and level floorsurface, preferably in a corner of the room

5. Connecting water inlet hoses• Connect the water supply inlet hose in accordance with regulations of your local water company

b) Drain hoseThe water drain hose could be placed either at the side of abasin, or connected directly to the drain. The hose should not besharply bent. The water drain hose should be secured with thesupplied elbow to prevent it falling to the ground.

6. Electrical connections• Electrical connections must be carried out by a qualifiedtechnician in compliance with the manufacturer’s instructionsand local safety regulations• Data concerning voltage, consumption and fuses arelocated behind the appliance door• The appliance must be connected to the mainsexclusively by means of a socket with an earth connection inaccordance with established regulations. The washing machinemust be earthed by law. The manufacturer declines all liabilityfor damage to property or injury to persons or animalsdue to non-compliance with the directions given above• Do not use extension leads or multi sockets• Before any maintenance on the washing machine disconnectit from the mains supply• Access to the mains plug or to disconnection from mainssupply via a double-pole switch must be ensured at all timesfollowing the installation• Do not operate the washing machine if it has been damagedduring transport. Inform an Authorised Service Centre or yourlocal retailer.• Mains cable replacement is only to be carried out by anAuthorised Service Centre• The washing machine must only be used in the householdfor the prescribed uses

Minimum housing dimensions:

Width: 610 mmHeight: 860 mmDepth: 550 mm

CAUTION: If this appliance is supplied from a cord extensionset or an electrical portable outlet device, the cord extensionset or electrical portable outlet device must be positioned sothat it is not subject to splashing or ingress of moisture.The appliance is to be connected to the water mains usingnew hose-sets. Old hose-sets should not be reused.

The hose should be placed between 40 and100 cm. from the ground.

8

To remove any residual water used in testing by the manufacturer, we recommend that you carry out a shortwash cycle withoutlaundry.

1. Turn on the tap.2. Close the door.3. Pour a small amount of detergent into the detergent compartment.4. Select and start a short programme (Please see programme table)

9

1. Sort the laundry according to...

• Type of fabric / care label symbolCottons, mixed fibres, easy care/synthetics, wool, handwashed items

• ColoursSeparate coloured and white items. Wash new coloured articles separately

• SizeLaundry items of different sizes distribute themselves better in the drum and optimise the washing and spinning action

• DelicatesWash small items (e.g. nylon stockings, belts etc.) and items with hooks (e.g. bras) in a washbag or pillow case with a zipfastener. Always remove curtain glides or wash curtains with the glides inside a cotton bag

2. Empty all pocketsCoins, safety pins etc. can damage the laundry, drum and tub

3. ClosuresClose zips and hooks and eyes; Tie loose belts or straps together

5 Preparing the wash

4 Before the first wash cycle

The choice of detergent depends on:• type of fabric (cottons, easy care/synthetics, delicate items, wool).

Note: Use only specific detergents for washing wool

Remarks:White residues on dark fabrics are caused by insoluble compounds used in modern phosphate-free powder detergents. If thisoccurs, shake or brush out the fabric or use liquid detergents. Use only detergents and additives specifically produced for frontloading washing machines. When using descaling agents, dyes or bleaches for the pre-wash, make sure that they are suitablefor use in domestic washing machines. Descaler could contain components which can attack parts of your washing machine.Do not use any solvents (e.g. turpentine, benzene). Do not wash fabrics in the machine which have been treated with solventsor flammable liquids.

10

6 Detergent and additives

Stain removal• Blood, milk, eggs etc. are generally removed by the automatic enzyme phase of the programme• Pre-treat heavily-soiled areas with stain remover if necessary

Dyeing• Only use dyes that are suitable for washing machines• Follow the manufacturer’s instructions.• Plastic and rubber parts of the washing machine can be stained by dyes

Loading the laundry1. Open the door2. Unfold the laundry and place it loosely in the drum. Observe the load sizes given in the Program Selection Table.

Note: Overloading the machine will result in unsatisfactory wash results and creased laundry

3. Close the door

Detergent Dispenser

The detergent dispensing drawer comprises 3 compartments:– left compartment ( II ) for main wash– middle compartment for fabric softener– right compartment ( I ) for pre-wash

Attention! Fill the softener according to the supplier recommendation (app.<100 ml). Do not exceed the “MAX level” marked on the detergent dispenser.

Follow the dosage recommendations on the detergent pack. They depend on:• degree and type of soiling• size of wash

- full load follow the detergent manufacturer’s instructions;- half load: 3/4 the amount used for a full load;- Minimum load (about 1 kg):1/2 the amount used for a full load• water hardness in your area (request information from the water company). Soft water requires less detergent than hardwater.

Notes:

Too much detergent can result in excess foam formation.If the washing machine detects too much foam, it may prevent spinning.Insufficient detergent may result in grey laundry in time and also calcifies the heating system, drum and hoses.

11

12

Control Panel

On/Off Button

Time delay adjustment button

Remaining time

Start/Pause/Cancelbutton

Program follower

Spin speed selection

Program selection knob Auxiliary Functions

Auxiliary Functions

PrewashA pre-wash should only be used for very heavily soiled laundry. Without prewash you save energy, water, washing powder andtime.

Time SaverShortens washing time for lightly soiled fabrics. This function can be used for cotton, synthetic and daily load programs.

Extra RinseBy using this function your machine will add another rinse process to the three rinse processes that it has already done. Thisadditional rinse will reduce any affects on sensitive skin.

Anti-CreaseTo avoid wrinkling of your clothes, select this function. When Anti-Crease is selected load size should be kept small.

Spin Speed SelectionUsing this button, you can select final spin speed up to 1000 rpm. If you do not want to spin the load, select “No Spin” option.

Rinse HoldIf you desire to leave your synthetic and wool fabrics in the machine after the wash program you may select the Rinse holdoption to prevent them getting wrinkled. To cancel the “Rinse Hold” function, press the “Start/Pause/Cancel” button first, selectthe desired spin speed and then repress the “Start/Pause/Cancel” button.

13

7 Program Selection and Washing Machine OperationEnsure the machine is plugged in.1) Press the On/Off button.2) Open the door.3) Place your laundry into the machine according to the recommended load capacity (please see Programme table) and close thefront door.4)Turn the program selection knob and set the desired program.(See Programme Table)5) Select the spin speed according to the desired program.6) Select desired auxiliary functions.7) Fill the fabric softener and the detergent into the related compartments, and close the detergent dispenser box.8) Push the Start/Pause button to operate your machine. In the mean time the Start/Pause led will be on. You can follow the washingsteps by means of the program follower.

14

3

5

1

6

42

7 8

15

Program selection

*Energy Labelling program acc. to AS/NZS 2040Depending on water, textile and ambient conditions the actual values given on or with the machine can deviate from the declared standard values,as they are tested according to the laboratory conditions

Cotton 90

Cotton 60

Cotton 40*

Heavy 40

Synthetics 60

Synthetics 40

Synthetics 30

Daily Load 40

Delicates 40

Woollen 40

Woollen Cold

Handwash 30

Quick Wash

Rinse

Spin

Drain

Programme Fabric typeTimeSaver

ExtraRinse

RinseHold

MaxLoad(kg) En

ergy

Con

sum

ptio

n(k

Wh)

Wat

erC

onsu

mpt

ion

(l)

Heavily soiled fabrics made from cotton or linen,heat resistantHeavily soiled fabrics made from cotton or linen,heat resistantNormally soiled fabrics made from cotton, non-colour fastHeavily soiled fabrics made from cotton or linen,heat resistantNormal soiled fabrics made from cotton/syntheticsblended, heat resistantLightly Soiled Easy care fabrics made from cotton,synthetics or blended fabrics (non-color fast)Very Lightly Soiled Easy care fabrics made fromcotton, synthetics or blended fabrics (non-color fast)

Everyday clothes

Sensitive, easy care fabrics made from cotton,synthetics or blended fabricsHand wash marked labelled clothes, blendedfabricsHand wash labeled wool and easy care, blendedfabricsSpecial programme for Hand wash labelled wooland silk

I+II

I+II

I+II

II

I+II

I+II

I+II

I+II

II

II

II

II

-

-

-

-

Pro

gram

Dur

atio

n(~

min

)

Anti-Crease

6

6

6

6

3

3

3

3.5

2

1.5

1.5

1

2.5

6

6

_

•••

••••

•••

••••

•••

•••••••

•••

•••••••

•••

•••••

DetergentDispenserPrewash

Lightly Soiled less amount fabric

Rinsing

Spinning

Draining

139 57 2.30

140 57 1.14

142 57 0.84

177 57 0.75

103 58 0.95

100 58 0.55

85 58 0.20

60 58 0.40

62 55 0.35

55 50 0.30

48 50 0.04

40 35 0.15

30 50 0.17

23 15 0.15

19 _ 0.08

2 _ _

Child LockTo prevent the knobs from being played with by children you may activate the “Child Lock” option. Activating the “Child Lock”option prevents any change from being made to a set program.To activate child lock, press both on the second and the fourth auxiliary function buttons together for 3 seconds after themachine starts the washing operation.

Only On/Off button will be in operation when the child lock option is selected.

To deactivate child lock, re-press same auxiliary function buttons (second and fourth) for 3 seconds.

In order to open the door at the end of the washing program or to change program selection, child lock must be deactivatedif selected.

On/OffWhen you press the On/Off button, your machine is ready to select the desired program. When the desired program isselected, related spin speed can be adjusted and the duration of the program can be observed on the display. To switch themachine off, repress the On/Off button.Washing can only then be started when the button is pressed.

Pressing the On/Off button does not mean that the washing operation is started! To start the washing, press the Start/Pausebutton!

16

End of the Program

At the end of the washing, all related leds on the control panel will be on. Related duration time of the selected program isdisplayed and the machine is ready to start again.To switch off the machine, press the On/Off button.

Auxiliary Function SelectionIt is not possible to activate all auxiliary functions in all wash programs. If any auxiliary function is selected, its led will be on.For example, if the cotton program is selected, “Time Saver” and “Pre-wash” functions can not be selected at the same time.If “Pre-wash” button is selected first and the “Time Saver” function next, the led of the pre-wash function will be off as it isnot active any more.

Program FollowerIf the machine is on, a program can be followed by means of the program follower. If a washing step is over and the nextstep is started, the led of the previous step will continue to light. It means if the washing operation is finished, all relatedwashing steps on the program follower will be on.Pre-wash button led will be on, only if this auxiliary function is selected.

17

Adding additional LaundryPress the Start/Pause button. If the water level does not exceed the limitations, in 1 to 2 minutes door lock will deactivated.It means the washing machine is ready to add laundry.If after 2 minutes the door is unable to be opened, it means the water level inside the machine is too high to open the doorand add laundry. (Look at Program Cancelling).

Press Start/Pause button again to let the program continue.

Unloading the machineThe machine stops automatically at the end of the selected programme. Turn off the taps. After 1-2 minutes the door lock willde-activate. Open the door. Press the On/Off button to switch off the machine.Unload the machine and leave the front door open. Check to see if there is any water left in the door hood. If so, remove witha soft cloth.

Time DelayBy using the time delay buttons, the start time of any program can be delayed. Time delay can be set at intervals of 30 min.On the display, the delayed starting time is added to the duration of the program.For example, if the program duration is 2 hours and 16 min and you delayed the program for 2 hours, the display will show“4:16”. After the time delay is set, press Start/Pause button. The washing cycle will be started after 2 hours.

Program CancellingIf the program has started and you want to cancel it, press and hold down the Start/Pause button for 3 seconds. The programwill move to the “spin” step and related led on the program follower will be on. Machine will start to pump for draining and thedoor can be opened after 1-2 minutes.

18

Detergent dispensing drawerClean when necessary:1. Open the drawer as far as possible.2. Push down the depression on the suction cup and pull the drawerout completely.3. Clean the drawer under warm running water. Pull off the suctioncup; Cleansuction cup and opening in the drawer with warm running water,pierce the opening with a needle if necessary. Replace the suctioncap.4. Wipe off detergent residue from the drawer guides. If present,remove calc deposits from the water-jet nozzles (inside the drawer).

8 Care and maintanence

Water intake filterAt the end of the water intake connection module and water inlethose-tap side, there exists filters. These filters prevent any dirt andobjects passing into the machine. It is advisable that these filtersshould be cleaned every 30-40 washes. To clean the filter, first turnthe tap off. Then, disconnect the hose and clean the filter with athin brush. If the filter is very dirty, you may clean it by pulling outwith pliers. To clean the filter at the tap side of the hose, pull it outby hand and clean the filter under the tap water.

HoseTo prevent any leakage, have a technician check the hoses everytwo years. If the machine is placed at cold ambient temperatures,the water remaining inside the pump and hoses should be removedfrom the filters. Also to prevent freezing, empty the water intakehoses by disconnecting from taps.

DrumDo not leave any metal objects (pins, needles, etc.) inside thedrum. These objects may cause rust on the drum surface.

19

Cleaning the Foreign matter trap

It is recommended that this is cleaned once every 30 cycles.Follow instructions below:

1) Drain off the water completely…2) Switch appliance off, unplug the power cable, close the watertap. Allow hot suds to cool off sufficiently. This poses a risk ofscalding.3) Open the service door by pushing on the button. Take outthe drain pipe and hold it over a bowl. Pull the seal off the drainhose and allow the water to drain out one bowl at a time.There may be more than 20 litres of water left in the machinewhen the drum is full (e.g. after a power failure)!4) Turn the foreign object trap 1/2 turn to loosen it (anti-clockwise)and soak up the remaining water with a cloth. Once no morewater is coming out, turn the foreign object trap until it iscompletely free and remove it.5) Clean foreign object trap and the pump opening. Check ifthe pump impellor (in the pump opening) can be turned freely.6) Replace the cap on the drain hose and put it away.7) Replace the foreign object trap and screw in it tight (inclockwise direction).8) Close the service door.

20

Do not usebleach

Washingtemperature

Can be washedat centrifugalmachine

Do not washcentrifugalmachine

Dry on horizantalsurface

Warm iron

Bleach canbe used

Do not machinewash

Line dry

Descriptions of the international textile care label (ITCL) symbols

60°

No spinNo dry cleaning

Machine does not start, no lights show.Check whether:• The mains plug is inserted in to the socket.• The wall socket is functioning correctly. (use a table lampor similar to test)

Machine does not take water.• Check the front door for proper closure.• Check inlet hoses connected and turned on.

Inlet water is directly discharged.• Check if the discharge hose placed as described in theusers manual or not.

Water coming from beneath the machine.• Check the water inlet and drain hoses. Tighten theconnections. The washers of the hoses may be worn out.•Check the pump filter is closed properly.

Foam coming out of the detergent dispenser.• Check whether your detergent is suitable for front loadingwashing machines.• Check amount of detergent used against detergentsupplier‘s instructions. (you may have used too muchdetergent)

Pump does not drain water.• Clean the pump filter.• Check whether the drain hose is bent or not.

Chemicals canbe used

Do not wash Dry clean

P A

Iron permitted Do not iron

9 Before calling service

21

Manufacturer’s Warranty

When you purchase any new Fisher & Paykel whiteware Product you automatically receive a two year Manufacturer’s Warrantycovering parts and labour for servicing.

Fisher & Paykel undertakes toRepair or, at its option, replace without cost to the owner either for material or labour any part of the Product, the serial numberof which appears on the Product, which is found to be defective within TWO YEARS of the date of purchase.

This warranty DOES NOT coverA Service calls which are not related to any defect in the Product. The cost of a service call will be charged if the problem isnot found to be a Product fault. For example:1. Correct the installation of the product.2. Instruct you how to use the product.3. Replace house fuses or correct house wiring or plumbing.4. Correcting fault(s) caused by the user.5. Blocked pumps.B Defects caused by factors other than:1. Normal domestic use or2. Use in accordance with the Product’s User Guide.C Defects to the Product caused by accident, neglect, misuse or Act of God.D The cost of repairs carried out by non-authorised repairers or the cost of correcting such unauthorised repairs.E Normal recommended maintenance as set out in the Product’s User Guide.F Repairs when the appliance has been dismantled, repaired or serviced by other than Fisher & PaykelAUTHORISED SERVICE CENTRE or the selling dealer’s service department.

Service under this manufacturer’s warranty must be provided by an Authorised Service Centre (refer to the Customer Caresection for contact details). Such service shall be provided during normal business hours. This warranty certificate should beshown when making any claim.

Note:This Warranty is an extra benefit and does not affect your legal rights and applies only to product purchased in New Zealandand Australia.

Please keep this User Guide in a safe place.Do not return to Fisher & Paykel.