aux 1-4 master flashing led - ocean...
TRANSCRIPT
AUX 1-4 MASTERLEVEL CONTROLS
FUNCTIONS AND CONTROLS
OPERATIONAL DESCRIPTION
Connect a signal to an I/P module via the female x-l-r socket on the back of the rack and with the channel pan control in it’s central position, advance the input level controluntil the green signal present LED (-20) is fully illuminated.
We reserve the right to change product specifications, features or designin our constant quest for improvement.
SOLO MASTER WITH FLASHING LED
HEADPHONE LEVELCONTROL
MASTER MONITORLEVEL CONTROL
AUX SEND OUTPUTJACKS (BALANCED)
12 SEGMENT BARGRAPH DISPLAYS FOR GROUP AND SOLO LEVELS
L/R GROUP MASTERLEVEL CONTROL
HEADPHONE OUTPUTJACK
GENERAL DESCRIPTIONThe Ocean Audio 500 Series Master Output module when used in conjunction with any number of Ocean Audio Input modules, makes a powerful mixing console for the 500 Series rack system.This two width module provides a master level control for the stereo output together with accurate bargraph meters that also read the solo levels when activated.It also provides master level controls and balanced output jacks for the four auxiliary sends. There is also a solo master level control, headphone level and output jack plus an independent control room monitor level control.
The module should be carefully slotted into the appropriate two positions of any 500 Series Rack.
By means of the ribbon cable supplied with any Ocean Audio I/P module, connect it to the I/P module which can be located on either side of the O/P module.These 16 way connectors can be found on either side of the module printed circuit board. The rack can now be powered up.
The following procedures should be carried out without power applied to the rack.
Now turn the L/R Group Master control until the bargraph displays indicate signal. It is a good idea to put the L/R Group Master control to approximately three quarters of it’s travel which will correspond to 0db output. The I/P module level control shouldnow be advanced to obtain a suitable reading on the bargraph display.If the ‘SOLO’ master control is turned clockwise and the ‘SOLO’ button on the input isdepressed, the red LED next to the solo master control will flash and the solo signal will be indicated on the bargraph meters.By plugging a balanced (stereo) jack into any or all of the four ‘AUX SEND’ jacks the auxiliary sends can be accessed. Turning the associated master level controlwill adjust the overall level of the auxiliary send.
REAR PANEL CONNECTIONS
MASTER O/PLEFT (MALE X-L-R)
MASTER O/PRIGHT (MALE X-L-R)
MONITOR LEFT(FEMALE X-L-R)
MONITOR RIGHT(FEMALE X-L-R)
SYSTEM FLOW DIAGRAM
Make sure that all controls are in their minimum (anti-clockwise) positions.
0dBMASTER
LEFT
6dB
VV
0dB SOLORELAY
6dBMONITORMASTER
6dB
0dBSOLO MASTER
LEVELSOLOMIX AMP
LEFT
0dB
0dB
12 SEGMENTBARGRAPH
DISPLAY
LEFT
6dB
0dBSOLO
MIX AMPRIGHT
SOLOLED
H/PHONES
12 SEGMENTBARGRAPH
DISPLAY
RIGHT
MASTERRIGHTMASTER MIX
BUSS RIGHT 0dB 0dB
SOLO MIX BUSSLEFT
SOLO MIX BUSSRIGHT
SOLO D.C.
MASTER MIX BUSS LEFT
MASTERMIX AMP
LEFT
MASTERMIX AMPRIGHT
MASTERO/P AMP
LEFT
MASTERO/P AMPRIGHT
0dBAUX 1
MASTER
6dBAUX 1
AUX 1MIX AMP AUX 1
O/P AMP
VV
VV
0dBAUX 2
MASTER
6dBAUX 2
AUX 2MIX AMP AUX 2
O/P AMP
VV
VV
0dBAUX 3
MASTER
6dBAUX 3
AUX 3MIX AMP AUX 3
O/P AMP
VV
VV
0dBAUX 4
MASTER
6dBAUX 4
AUX 4MIX AMP AUX 4
O/P AMP
VV
HEADPHONELEVEL
AUX 1 O/P
AUX 2 O/P
AUX 3 O/P
AUX 4 O/P
MASTER O/P LEFT(MALE X-L-R)
MASTER O/P RIGHT(MALE X-L-R)
MONITOR O/P LEFT(FEMALE X-L-R)
MONITOR O/P RIGHT(FEMALE X-L-R)
VVVV