Operating Manual

Atomic 600 DCS®

bona.com 800.872.55152

Atomic 600 DCS®Table of Contents

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operative Range and Correct Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Stand-by Power Supply (Generator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Advice for Operators of Dust Containment Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7 Description of the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Set-up Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Dust Collection Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Maintenance and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 10

Schematics / Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 14

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 90 Day Performance Pledge Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

The following safety instructions must be followed as shown in this operating manual. Failure to do so may result in hazard to health or possible death.

bona.com 800.872.5515 3

Atomic 600 DCS®Atomic 600 DCS® Technical Data

Rating ___________________________________________________________________________Model: Bona® Atomic 600 DCS®

Manufacturer: Bona US

(800) 872-5515

bona .com

Unit Specifications __________________________________________________________________Machine Type: Bona Atomic 600

Working Width: 30in (72cm)

Dust Capacity: 30 gallon

Dust Hose Connection: 2in (6 .3cm) / 1 .5in (5 .1cm)

Dimensions: Length 57in (145cm)

Width 27in (68cm)

Height 60in (152cm)

Weight 284 lbs . (129 Kg)

Connected loads of the electrical system: Power (2) 2 .1 HP Motors

Electrical Connection 120/240v 50-60Hz Single Phase – (the above is a typical generator style wiring setup) note: see wiring diagram in this manual under Reference Guide and Procedures .

The above connection creates two 120v connections that connect to each individual motor circuit . User may use two separate 120v circuits as an option as opposed to wiring the 120/240v .

Operative Range and Correct Usage ____________________________________________________The Bona Atomic 600 is designed to be used for the purpose of collecting hardwood floor sanding dust . The machine cannot be used for other purposes . The manufacturer will not be liable for damages resulting from incorrect usage . In case of improper usage the user is responsible for all risks and damages .

Stand–by Power Supply (Generator)_____________________________________________________ If the Bona Atomic 600 is operated using a generator, the generator must be operated in accordance with the current local electrical code (this applies in particular to the protective ground conductor) in order to ensure that all safety devices are functioning and to be able to eliminate possible damage to electrical components .

Advice for Operators of Dust Containment Systems_________________________________________During the operation of the Bona Atomic 600 it may be possible to exceed the acceptable noise level of 79 dB(A) . This is dependent on the different job site environments and other local factors . When the noise level exceeds this safety threshold, the machine operator and the persons working near the machine must wear approved sound–insulating devices .

bona.com 800.872.55154

Atomic 600 DCS®Operator Safety Instructions

DANGER means: Severe bodily injury or death can occur to you or other personnel if the statements found on this machine or in this Owner’s Manual are ignored or are not adhered to . Read this entire manual before operating this machine .

WARNING means: Injury can occur to you or to other personnel if the WARNING statements found on this machine or in this Owner’s Manual are ignored or are not adhered to . Damage to the machine or to other property may occur as well, if the WARNING is ignored .

NOTE: The reading and understanding of the Owner’s Manual is imperative prior to operating this machine . If you or your operator(s) cannot read English, have this manual explained fully before attempting to operate this machine . Si Ud . o sus operadores no pueden leer el inglés, el contenido completo de este manual será explicado antes de intentar operacion de esta máquina .

Sanding/finishing wood floors can create an environment that can be explosive . The following safety procedures must be adhered to:

•Cigarettelighters,pilotlights,andanyothersourcesofignitioncancreateanexplosionwhenactiveduringa sanding session . All sources of ignition should be extinguished or removed entirely, if possible, from the work area .

•Workareasthatarepoorlyventilatedcancreateanexplosiveenvironmentwhencertaincombustiblematerialsarein the atmosphere; i .e ., solvents, thinners, alcohol, fuels, certain finishes, wood dust and other combustible materials . Floor sanding machines can cause flammable material and vapors to ignite . Read the manufacturer’s label on all chemicals being used to determine combustibility . Keep the work area well ventilated .

•Hittinganailwhilesandingcancausesparksandcreateanexplosionorfire.Alwaysuseahammerandpunchto countersink all nails before sanding floors .

Electrocution could occur if the machine is used on a power circuit that repeatedly trips or is undersized . Have a licensed electrician check the fuse, breaker, or power supply .

Electrocution could occur if maintenance and repairs are performed on a unit that is not properly disconnected from the power source . Disconnect the machine from all power .

Electrocution could occur if the machine is used on an ungrounded electrical circuit . Never remove or disable the grounding supply conductor on the electrical cord .

Consult an electrician if the grounding conductor is missing or if you suspect your circuit is not grounded properly .

Use of this machine with a damaged power cord or plug could result in an electric shock . Do not pull or carry by cord, use power cord as a handle, close a door on cord, or pull cord around sharp edges or corners .

Do NOT unplug by pulling on cord . To unplug, grasp the plug, not the power cord . Do NOT handle plug or operate machine with wet hands . Do NOT put any objects into motor openings .

bona.com 800.872.5515 5

Atomic 600 DCS®Atomic 600 DCS® Operator Safety Instructions (con’t)

Electrocution or injury could occur if the power cord is run over and damaged by the sanding machines . Keep the cord from contact with the sanding heads . Always lift the cord over the machine and sand away from the cord .

Moving parts on this machine can cause serious injury and or damage . Keep hands, feet, hair, and loose clothing away from all moving parts of the unit .

Operating a vacuum without all guards, doors, or covers in place can cause an injury or damage .

Do not pick up any objects that are hot, burning or smoking, such as cigarettes, matches or cinders .

Injury to the operator or bystanders could occur if the machine is plugged in while performing maintenance, servicing, changing filter, or inspecting . Always unplug machine when not in use .

Do not use solvents or other flammable products to clean this machine .

Danger: Dry use only . Do not use for liquid recovery, which could result in motor failure, electric shock, and electrocution .

Airborne sanding dust should not be breathed in while operating a sander . Always wear an approved particulate respirator while operating sanding equipment .

Injury to the eyes and or body can occur if protective clothing and or equipment is not worn while sanding . Always wear safety goggles, protective clothing, hearing protection, and a dust mask while sanding . Exposure to high noise levels can cause hearing loss or impairment . Wear OSHA-approved hearing protection (earmuffs) when using this equipment .

Bodily injury could occur if power is supplied to the machine with the power switch already in the “ON” position . Always check to assure the power switch is “OFF” before connecting the machine to its power source .

Do not use this machine as a step or furniture . Do not ride on this machine .

Check filters . Clogged filters may lead to overheating and subsequent electrical problems which may lead to machine failure or electrical shock .

Do not put any objects into openings . Do not use with blocked openings . Keep free from dust, lint, hair or anything that may reduce airflow .

KEEP AWAY FROM CHILDREN

bona.com 800.872.55156

Atomic 600 DCS®General Information

Description of the Machine ___________________________________________________________The Bona® Atomic 600 DCS® is a dust collection system with two independent vacuum motors that runs on 120 volts 50/60Hz . They may be run off of a 120/240 volt split power supply or off of two independent 120 volt 15 amp circuits .

An onboard cyclone separator collects and deposits most of the dust during operation into the main collection barrel . A small percentage of dust may also be collected in the filter chamber located beneath the motor housing . Both of these collection areas are designed to be used with a properly sized bag in place for dust collection efficiency and ease of disposal .

In addition, two independent, patent-pending AirBlast™ filter cleaning mechanisms are integrated into the bottom of the motor housing .

Included___________________________________________________________________________

Set-up Instructions _________________________________________________________________

Install properly sized plastic collection bag into main collection barrel and filter chamber with bag excess gathered and smoothly draped over edge of tank .

DO NOT RUN UNIT WITHOUT THE BAGS IN PLACE AS THIS WILL ALLOW DUST TO BE PULLED DIRECTLY INTO THE MOTOR AND WILL FLOW OUT OF THE EXHAUST PART, THEREBY CONTAMINATING THE WORK ENVIRONMENT!

Your vacuum is equipped with a dual circuit indicator light, showing when two 120v cords are properly plugged into separate fuse circuits .

Secure latches on barrels . The hook latches are adjustable . Occasionally adjust

the tension on the latches to insure an adequate seal .

Check that negative pressure hoses are attached to parts on both collection barrels .

Hour Meter .

USE ONLY HEAVY DUTY BAGS! ( 4mil or greater ) Thin bags may tear, pop and or pull into the cyclone during operation.

•Bona® Atomic 600 DCS® (part # AD6003460) •Complete Chassis with Barrels, straps, HEPA Filters, Hoses •Operating Manual•Docking Station ( 1 )•2” Lead Hose with Cuffs ( 25’ )•2” Smooth-Bare Hose with Cuffs ( 50’ )

•1 1/2” Smooth-Bare Hose with Cuffs ( 50’ )•Mesh Hose Carry-Bags ( 2 )•Aluminum Y-Slitter ( 1 )•38” x 48” 30 gal . Collectoin Bags - 6mil ( 7 )•Power Cord with Plugs ( 2 )

bona.com 800.872.5515 7

Atomic 600 DCS®Atomic 600 DCS®

Operation Instructions _______________________________________________________________

Plug into any two 120v 15 or 20amp outlets . For 120v operation you MUST have two separate 120v 15 or 20 amp circuits in order to run both motors simultaneously . If using two 120v circuits to power the unit remove the 120v female plugs that are a part of the unit and plug your power cords into the male flanged 120v plugs as shown .

Optional 120/240v - 4 wire connection . Check the enclosed external wiring diagram to insure the wiring on your cable is correct . If wiring is incorrect the voltage may be too high for the motors resulting in damage which is not covered under the warranty . The 240v wiring splits off into two 120 volt circuits . This allows the motors to run on either the 240 volt setup or two, separate 120 volt lines without any adaptation . Plugs are twist-lock style .

Included docking station can be bolted to vehicle/trailer for secure transportation .

Cyclone has a T-hook that fits in tray slot for easy maintenance .

This unit collects over 98% of the dust in the cyclone collection barrel during operation . Eventually the small amount of dust that gets in the filter chamber will begin to clog the filter, thereby creating air flow resistance and loss of performance . The unit is equipped with a minihelic gauge that measures the resistance of airflow through the filter . When the filter reaches approximately 20” h20 on the gauge, which is half way, the filter should be cleaned with the use of the AirBlast™ clearing system . The AirBlast™ clearing operation should be repeated every 1-2 hours, but varies with amount of dust being collected over a given period . One switch turns on both motors .

To clean the filter simply pull the AirBlast™ catch lever back quickly and release . The filter has been cleaned and you are ready to continue operation . Repeat .

Dust Collection Capacity__________________________________________________________________ Dust collection barrel has a 30-gallon capacity . The actual dust collection capacity should be based on whatever is an acceptable weight to handle for the operator . If the barrel is filled to create an unmanageable weight for an individual to safely lift, operator is required to utilize a mechanical lifting device to dispose of dust in an approved receptacle . Consult and abide by local regulations regarding disposal of debris .

General Information (con’t)

•1 1/2” Smooth-Bare Hose with Cuffs ( 50’ )•Mesh Hose Carry-Bags ( 2 )•Aluminum Y-Slitter ( 1 )•38” x 48” 30 gal . Collectoin Bags - 6mil ( 7 )•Power Cord with Plugs ( 2 )

bona.com 800.872.55158

Atomic 600 DCS®Maintenance and Inspection

Special attention to regular maintenance of the machine and its parts are imperative for effective operation and safety .

In order to prevent unnecessary downtime it is recommended to keep a limited number of spare parts on hand .

The following should be replaced at least every 1000 hrs of operation . Upon inspection, if filter damage is noticed, replace immediately .

Bona Item # AS37B0368 HEPA Filter Cartridge (2 / unit)

Bona Item # AS37H0651 Brush Set Motor Brushes (2 sets / unit)

Daily Maintenance and Inspection ______________________________________________________

•Cleanallsurfaceswithadry,lintfreecloth

•Inspectallelectricalcablesforcutsandreplacedamagedchords

•Checkthatallelectricalconnectionsaresecureandsnug

•Inspectfilterforanyvisibledamage

•Inspectmotorexhaustareatoinsurenodusthasbeenblowingout

•Removedustcollectionbagsfromcollectionbarrelandfilterchamber. Dispose of properly in accordance with local regulations .

•Checkelectricalconnectionsforcleanliness.

•Checkdustcollectionbarrelandfilterchambertoinsurethatthebagshavebeenchanged.

•Checkhosestoassuretightconnections.

•Checkhosesconnectedtofilterlidfordamage.

•Makesurelidsealsareingoodconditionandthelidssealproperly.

•Checklatchesonthelidsandadjustaccordingly.

•Checkcastersfordebrisandmakesuretheyareingoodworkingcondition.

If machine is not collecting dust at an adequate level to meet all local regulations and job requirements, shut down vacuum system and sanding machines to immediately perform repairs and maintenance procedures.

bona.com 800.872.5515 9

Atomic 600 DCS®Atomic 600 DCS® Troubleshooting

Failure Possible Reasons of Failure Corrective Action

Too much dust getting into the filter chamber and bag gets sucked up into cyclone during operation .

Suction leak in the cyclone lid . Adjust latches . Replace lid seal .

Suction leak around one of the cyclone collection barrel wheel stems .

Check by running with a little bit of dust in the barrel with no bag . If leaking you will notice a blow pattern of dust around the leaking wheel stem . Repair seal and tighten .

Suction leak at the equalizer vacuum hose on the side of the collection barrel .

Check the seal on the port plate and insure the small hose cuff is glued on hose securely and not leaking air .

Too much dust getting into the filter chamber and bag is sucked tight to the side of cyclone collection barrel during operation (which is normal) .

Cyclone has debris stuck in it . Inspect inside of cyclone and remove debris .

Cyclone lid is not sealing properly . Adjust latches . If problem persists, replace seal on cyclone lid assembly .

Not enough suction . Filter is clogged . The gauge should read zero after cleaning with AirBlast™ valve . If not, actuate AirBlast™ valve and change plastic bag in filter chamber .

A lid is not sealed properly . Check lid seals and replace if necessary or adjust latches .

Vac motor not operating properly . Check input voltage to insure proper level . Replace motor brushes or motor if necessary .

Disconnected or damaged hose(s) . Inspect hoses for proper connections or damage . Re-connect or replaced if damaged .

Dust is not being picked up . Vacuum seems to be working properly .

Dust shroud on sanding machines are damaged, not down on the floor surface or ineffective .

Repair shroud, check for ineffectiveness and move down closer to the surface if necessary . Replace with sanding machines designed for dust containment .

Dust is blowing out of exhaust port on motor housing .

Filter seal is compromised . Remove filter, inspect seal and replace on unit . If problem persists replace filter .

Filter is damaged . Replace filter .

Bags are not in both barrels . Properly install bags in both barrels .

There is a hole in one of the bags . Replace damaged bag .

Prior to any repair work on the machine or drives, the machine must be secured against unintentional start-up . Put the machine in its Safety-off position .

bona.com 800.872.551510

Atomic 600 DCS®Troubleshooting (con’t)

Failure Possible Reasons of Failure Corrective Action

When using the 120/240 volt power setup, one motor runs and the other one doesn’t, but when the separate 120 volt inlet plugs are connected, both motors work .

One leg of the 120/240 volt connection is loose; plugs and or cable is improperly wired; problem at power source .

Check and repair wiring connection on flanged 120/240 volt power connector, plugs, cable and power source .

When using the 120/240 volt power setup, neither motor runs, but when the 120v inlet plugs are connected directly off of a 120 volt house connections they both work .

The neutral leg of 120/240 volt connection is loose .

Check and repair wiring connection on flanged 120/240 volt power connector, plugs, cable and power source .

Motor is not running . Circuit breaker is blown . Reset breaker .

Switch is bad . Replace switch .

Getting no power from power connections .

Check connections on all terminals .

Motor is bad . Replace motor .

Motor brushes need to be changed . Replace motor brushes .

For more information or questions contact Bona Technical Support at (800) 872-5515 or bona .com

bona.com 800.872.5515 11

Atomic 600 DCS®Atomic 600 DCS® Schematics / Parts List

Part # Key DescriptionAS37B0359 1 Lid Assembly Cyclone 600

AS37B0361 2 Chassis 600

3 Tank Clamp

AS37B0362 4 Tank 30 gal . Assembly Cyclone

5 2” Swivel Dual Caster

AS37H0278 5 3/4” Wire Wound Hose

AS37H0662 7 6” Gray Swivel Caster

AS37H0661 8 6” Gray Fixed Caster with Lock

AS37B0364 9 Tray 600

AS37B0365 10 Motor Housing 1 600

AS37H0348 11 2 1/2” Wire Wound Hose

AS37B0360 12 Lid Assembly Filter 600

AS37B0363 13 Tank 30 gal . Assembly Filters

AS37B0369 23 Control Panel Face Plate 600

AS37H0289 42 Utility Hook

AS37H0551 43 3” White/Clear SDH Helix Hose

AS37H0552 44 3” Cuff, White for 3” SDH Helix Hose

CONTROL PANEL 23

2 CHASSIS

MOTOR HOUSING 10

TRAY 600 9

TANK 30 GAL. FILTERS 13

LID ASSEMBLY FILTERS 12

7 6" GRAY SWIVEL CASTER

4 TANK 30 GAL. CYCLONE

3 TANK CLAMP

5 2" SWIVEL DUAL CASTER

1 LID ASSEMBLY CYCLONE

2 1/2" WIRE WOUND HOSE 11

8 6" GRAY FIXED CASTER W/ LOCK

6 3/4" EQUALIZER HOSE

UTILITY HOOK 4243 3" CLEAR SDX HOSE

44 3" CUFF FOR HOSE

bona.com 800.872.551512

Atomic 600 DCS®Schematics / Parts List (con’t)

Part # Key DescriptionAS37B0377 10 Motor Housing 1 600

AS37H0348 11 2 1/2” Wire Wound Hose

AS37B0370 11 Motor Bracket

AS37H0065 14 Vac Motor 120v Tangential Bypass (Bona Atomic 300 or 600)

AS37B0366 15 Motor Housing 2 600

AS37B0371 16 Motor Housing Side Cover 600

AS37B0367 17 Slide Valve Manifold Metal (top) 600

AS37H0668 18 Slide Valve Spring

AS37H0670 19 Slide Valve Manifold Plastic (top)

AS37H0671 20 Slide Valve Retainer Plastic (sides)

AS37H0664 21 Slide Valve Slide Plastic (bottom)

AS37B0368 22 Slide Valve Slide Metal (bottom) 600

1410 MOTOR HOUSING 1

11

16

MOTOR HOUSING 2 15

22

21

20

19

18

17

bona.com 800.872.5515 13

Atomic 600 DCS®Atomic 600 DCS® Schematics / Parts List (con’t)

Part # Key DescriptionAS37B0369 23 Control Panel Face

Plate 600

AS37H0095 24 Hour Meter

AS37H0665 25 Minihelic Gauge

AS37H0372 26 20 amp Panel Breaker

AS37H0086 27 Power Switch (Pro Series)

AS37H0694 28 Dual Circuit Sensor

AS37B0372 29 Control Panel Body 600

AS37H0677 30 Turn-Lock Male Flanged Receptacle, 240v

AS37H0669 31 Handle Grips

AS37H0686 32 Turn-Lock Male Flanged Receptacle, 120v

23

24

25

29

30

31

32

26

27

28

33

35

8

7

34

Part # Key DescriptionAS37H0662 7 6” Gray Swivel

Caster

AS37H0661 8 6” Gray Fixed Caster with Lock

AS37H0376 33 1 1/2” x 2 1/2” Black Rectangular Tubing Insert

AS37H0673 34 1 1/2” Black Square Tubing Inserts

AS37H0387 35 1 1/8” Wide x 1/2” Thick Black Plastic Strips for Tank to Sit On .

bona.com 800.872.551514

Atomic 600 DCS®Schematics / Parts List (con’t)

Part # Key DescriptionAS37B0360 12 Lid Assembly Filter 600

AS37H0363 13 Tank Assembly Filters 600

AS37H0052 36 Filter SBTX 15 .5” 3 Hook Conical

AS37H0690 37 Rubber Handle for Tank Strap

AS37H0386 39 Tank Clamp - Yellow Handle

AS37H0693 40 3/4” Equalizer Hose Flange

40

13

39

36

12

37

41

4

40

39

37

Part # Key DescriptionAS37B0362 4 Tank Assembly Cyclone

AS37H0690 37 Rubber Handle for Tank Strap

AS37H0386 39 Tank Clamp - Yellow Handle

AS37H0693 40 3/4” Equalizer Hose Flange

AS37H0365 41 2” Swivel Dual Caster

bona.com 800.872.5515 15

Atomic 600 DCS®Atomic 600 DCS® Schematics / Parts List (con’t)

Part # DescriptionAS37B0349 1 .5” x 50’ Hose with Cuffs B Blue

AS37B0358 12” Pig Tail for 240v

AS37B0354 2 Way Metal Splitter (2” x 2” x 2”)

AS37B0350 2” x 25’ Hose with Cuffs B Blue

AS37B0352 2” x 50’ Hose with Cuffs B Blue

AS37H0094 Dock Station Strap, Pull Type, Black

AS37H0059 Crate 600

AS37H0088 Docking Station

AS37H0087 Carrying Bag for Hose

AS37B0356 Bona® Atomic 600 DCS® Manual

AS37H0687 Turn-lock Female Connector End 120v

AS37H0093 Power Cord 110v 25’ 15 gal (gray, non marking)

AS37H0674 2 1/2” Wire Wound Hose Cuff

AS37B0357 #44 2 1/2” x 1/2” Hose Clamp

AS37B0355 #48 3” Blue Turn Key Clamp

AS37H0355 3/4” Hose Cuff

AS37H0374 3/4” Tube Cap

AS37H0289 Utility Hook

AS37H0673 Tank Strap Assembly

AS37H0058 4 MIL x 30 gal Bag 38” x 48”

bona.com 800.872.551516

Atomic 600 DCS®Limited Warranty

This Bona product is warranted to be free from defects in materials and workmanship under normal use and service for a period of two years from the date of purchase when operated in accordance with the instructions included .

This warranty is extended only to the original purchaser of this product. It does not cover normal wear on parts such as dust collection bags, filters, electronic components, electrical cords, motor brushes or rubber parts.If a problem occurs with this product, you should contact your nearest Bona Distributor, or Bona US directly for an authorized repair location nearest you . All freight costs in shipping the machine to the repair location are to be paid by the purchaser .

Bona US liability under this warranty is limited to repair of the product and/or replacement of parts and is given to the purchaser in lieu of all other remedies, including incidental and consequential damages .

Contact:

Bona US

2550 South Parker Road, Suite 600

Aurora, CO 80014

800 .872 .5515

90 Day Performance PledgeInnovation, quality and performance drive Bona’s Machine and Atomic Dust Containment business and are always the ultimate goal we strive for when

developing products for our customers.

To this end, Bona makes the following pledge:

If the purchased Bona machine does not perform as designed, due to a manufacturing defect during the first 90 days, the customer may choose to

have the machine repaired at no cost or can return the machine for a full refund.After 90 days the standard machine warranty will apply.