arc welding
DESCRIPTION
Arc Welding. Basic Safety. Warnings. Welding can be safe when proper measures are taken to protect yourself and others from potential hazards. Understand and follow all warning labels found on equipment and with all consumables. Potential Hazards. - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/1.jpg)
Arc Welding
Basic Safety
![Page 2: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/2.jpg)
Warnings
• Welding can be safe when proper measures are taken to protect yourself and others from potential hazards.
• Understand and follow all warning labels found on equipment and with all consumables.
![Page 3: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/3.jpg)
Potential Hazards• Protect yourself and others from potential hazards
including:
– Fumes and Gases– Electric Shock– Arc Rays– Fire and Explosion Hazards – Noise– Hot objects– Welding Sparks
![Page 4: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/4.jpg)
Fumes and Gases
•Welding fumes can be harmful to the welder causing implications such as:
oIrritation of the respiratory tractoMetal fume feveroSlightly increase the risk of lung cancer
•Use enough ventilation, exhaust at the arc, or both, to keep fumes and gases from your breathing zone and the general area•Use a respirator if needed or required by the process.•The ventilation system must be on while welding at all times.
![Page 5: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/5.jpg)
Electrical Shock
•Electric shock can kill •Do not touch live electrical parts
Primary Voltage –208 - 240, 416 - 480 volt input powerSecondary Voltage – 6 to 100 volts for welding
•Insulate yourself from work and ground•Follow all warnings on welding equipment•Wear insulated clothing•Always shut off machinery when done and roll the cords up neatly•Do not make repairs yourself, alert your instructor immediately!
![Page 6: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/6.jpg)
U.V. Rays•Welding will produce ultraviolet rays that are harmful to the human eye and skin. Proper protection is needed to avoid bodily harm. •Arc rays are ten times brighter than the sun and can injure eyes and burn skin•Precaution must be taken to protect your eyes and skin from UV radiation. The welding arc is brighter than the sun•Wear correct eye and body protection
o10 shade helmetoSafety Glasses under the helmetoGlovesoArm and Body Protection
JacketShoulder CoversCoveralls
![Page 7: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/7.jpg)
Fire Hazards and Material Safety• Welding sparks can cause fires and explosions• Sparks and spatter from the welding arc can spray up to 35 feet
from your work• Flammable materials should be removed from the welding area
or shielded from sparks and spatter• Always clean painted materials• All welding booths should be cleaned thoroughly• Have a fire extinguisher ready• Inspect area for fires 30 minutes after welding• Watch for sharp metal edges• Cool all welded metal in the water tank.
![Page 8: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/8.jpg)
Ear Protection
• Loud noises can damage your hearing• Keep loud noises at a safe level by using proper
hearing protection such as:– Ear plugs – Ear muffs
![Page 9: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/9.jpg)
ProtectiveClothing
•Welders must wear protective clothing for
oProtection from sparks, spatter and UV radiationoInsulation from electric shock
•Protective clothing includes …oFire-proof clothing without rolled sleeves, cuffs or fraysoWork bootsoWelding gloves, shirts jackets, bibs, and fire-proof pantsoWelding cap, helmet and safety glassesoEar protection – ear plugs and muffsoMost importantly safety glasses are to be worn at all times in the shop
![Page 10: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/10.jpg)
Improper Protective Clothing
• List and describewhat is wrongin this picture
![Page 11: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/11.jpg)
Basic Electricity and Welding
Arc WeldingBasic Safety
![Page 12: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/12.jpg)
Arc Welding Circuit and Concept
•The electricity flows from the power source, through the electrode and across the arc, through the base material to the work lead and back to the power source.
Identify all the above parts for the arc welder, describe the function of each part, and determine each of the parts safety aspects.
![Page 13: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/13.jpg)
Electrical Concepts
•Voltage – The electrical potential or pressure that causes current to flow
oMeasured in Volts•Current – The movement of charged particles in a specific direction
oMeasured in Amps•Polarity
oDC- (Direct Current Electrode Negative)oDC+ (Direct Current Electrode Positive)oAC (Alternating Current)
•ALWAYS REMEMBER THAT VOLTAGE WILL HURT BUT AMPERAGE CAN BE FATAL
DC - DC +
AC
![Page 14: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/14.jpg)
Electrical Lead Condition
•Before starting an operation, always check the condition of all electrical leads.•Cracked and worn leads can lead to fatal shock.•All electrode holders or “stingers” should be in tack and not cracked or missing pieces.•All plugs and outlets should be in tack. Never set-up a welder with a broken plug or into a broken outlet.Never operate a welder with splices showing in the leads.
![Page 15: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/15.jpg)
Shielded Metal Arc Welding
SMAW
![Page 16: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/16.jpg)
SMAW Process
![Page 17: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/17.jpg)
SMAW Key Parts• Electrode Holder: Also known as the “stinger” Handle-like tool that
holds the electrode while welding. – Never hold this part with your bare hand while welding.
• Ground Connection: Also known as the “workpiece connection clamp” that connects to the work to complete the electrical circuit
• Power Source: Where the welder plugs into• Amperage Scale: Determines the amount of “heat” or power the
welder will operate at.• Polarity Switch: Setting that determines how the electrons will flow
during the welding process.• On / Off Switch: Turns the welder on / off. Make sure the switch
function properly at all times.
![Page 18: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/18.jpg)
SMAW Principles
• The American Welding Society defines SMAW as Shielded Metal Arc Welding
• SMAW:– Is commonly known as ‘Stick’ welding or manual
arc welding – Is the most widely used arc welding process in the
world– Can be used to weld most common metals and
alloys
![Page 19: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/19.jpg)
SMAW Welding Circuit• Current flows through the electrode cable, to the electrode
holder, through the electrode, and across the arc• On the work side of the arc, the current flows through the
base material to the work clamp and back to the welding machine
![Page 20: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/20.jpg)
SMAW Process
Identify all the above segments for the SMAW process, describe the function of each segment, and determine if any safety aspects exist.
![Page 21: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/21.jpg)
The ElectrodeWhat is it?
• Is a consumable - it gets melted during the welding process• Is composed of two parts– Core Rod (Metal Filler)
Carries welding current Becomes part of the weld
– Flux Coating Produces a shielding gas Can provide additional filler Forms a slag
![Page 22: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/22.jpg)
Electrode Classification•Electrodes are classified by a numbering system•E6013
oE = Electrodeo60 or first two numbers = Tensile strength (thousands of poundso1 or third number = Welding positiono3 or fourth number = Welding current type and depth of weld penetration.
Pictured above are E-7018 electrodes. Identify what the tensile strength is for this electrode.
![Page 23: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/23.jpg)
Electrode ClassificationThird Digit
•Third Digit
E_ _ 1 _ = Usable in all directionsE_ _ 2 _ = Usable in flat and horizontal positions onlyE_ _ 4 _ = Usable for vertical down only
Pictured above are E-6011 electrodes. Identify what each digit resembles up to the third digit.
![Page 24: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/24.jpg)
Electrode ClassificationFourth Digit
•Fourth DigitE_ _ _ 0 = DC reverse polarity onlyE_ _ _ 1 = AC and DC reverse polarityE_ _ _ 2 = AC and DC straight polarityE_ _ _ 3 = AC and DCE_ _ _ 4 = AC and DC E_ _ _ 5 = DC reverse polarityE_ _ _ 6 = AC and DC reverse polarityE_ _ _ 8 = AC and DC reverse polarity
Pictured above are E-6013 electrodes. Identify what each digit resembles.
![Page 25: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/25.jpg)
The Arc•An arc occurs when the electrode comes in contact with the work-piece and completes the circuit … like turning on a light!
•The electric arc is established in the space between the end of the electrode and the work
•The arc reaches temperatures of 10,000°F which melts the electrode and base material
•Don’t look at the arc without proper eye protection.
•Wear proper body protection. The UV rays will cause bodily harm.
Arc burning off the electrode
![Page 26: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/26.jpg)
![Page 27: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/27.jpg)
Weld Puddle•As the core rod, flux coating, and work pieces heat up and melt, they form a pool of molten material called a weld puddle •The weld puddle is what a welder watches and manipulates while welding•Don’t touch the hot puddle!!! The metal is hot!!!
![Page 28: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/28.jpg)
Shielding Gas
23
Shielding Gas4•A shielding gas is formed
when the flux coating melts.•This protects the weld puddle from the atmosphere preventing contamination during the molten state•Don’t touch the metal!!! The metal is hot!!! •Shielding gas can cause bodily harm. Be sure proper ventilation is being used.
The shielding gas protects the molten puddle from the atmosphere while stabilizing the arc
![Page 29: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/29.jpg)
Solidified Weldment•As the molten weld puddle solidifies, it forms a joint or connection between two pieces of base material•When done properly on steel, it results in a weld stronger than the surrounding base metal•Don’t touch the metal!!! The metal is hot!!!
![Page 30: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/30.jpg)
Slag•Slag is a combination of the flux coating and impurities from the base metal that float to the surface of the weld. •Slag quickly solidifies to form a solid coating which slows the cooling rate of the weld •The slag can be chipped away and cleaned with a wire brush when hard•Don’t touch the metal!!! The metal is hot!!! •Slag can be dangerous when being removed. Wear the proper safety protection.
This welder chips the slag off of a weld during the repair of railroad tracks
![Page 31: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/31.jpg)
Gas Metal Arc Welding
GMAW“Mig”
![Page 32: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/32.jpg)
GMAW Defined
• An arc welding process that uses an arc between a continuous filler metal electrode and the weld pool.
• The process uses a shielding gas that protects the weld from contamination.
• Without using a shielding gas the weld becomes pitted and contains no strength value.
![Page 33: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/33.jpg)
Pitted GMAW Weldment
Weld is Pitted from improper flow of shielding gas
![Page 34: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/34.jpg)
GMAW Safety Points • Fumes and Gases can be dangerous
– Keep your head out of the fumes– Use enough ventilation, exhaust at the arc, or both, to keep
fumes and gases from your breathing zone and the general area– Local exhaust and mechanical ventilation can be used without
reducing weld quality • Electric Shock can kill – to receive a shock your body must touch the
electrode and work or ground at the same time– Do not touch the electrode or metal parts of the electrode
holder with skin or wet clothing– Keep dry insulation between your body and the metal being
welded or ground– The coil of wire is ‘electrically hot’ when the trigger is pulled
![Page 35: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/35.jpg)
GMAW Safety Points (Continued)
• REMEMBER – Gas Cylinders require SPECIAL safety precautions– Cylinders must be secured in an upright position– Cylinders should be located in an area away from arc
welding, cutting, heat, sparks, and flame– Shut off the gas cylinder when finished. – NCWHS uses a 75% carbon dioxide and a 25% argon
mix for shielding gas.– Don’t bleed or purge the lines after an operation. This
gas will not combust / burn.
![Page 36: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/36.jpg)
GMAW Process•During the GMAW process, a solid metal wire is fed through a welding gun and becomes the filler material•Instead of a flux, a shielding gas is used to protect the molten puddle from the atmosphere which results in a weld without slag
![Page 37: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/37.jpg)
GMAW Process (Continued)• Three things happen when the GMAW gun trigger is pulled:– The wire electrode begins to feed– The circuit becomes electrically ‘hot’– Shielding gas flows through the gun and out the nozzle
• Current flows from the power source through the gun cable, gun, contact tip to the wire and across the arc.
• On the other side of the arc, current flows through the base metal to the work cable and back to the power source
• Shielding gas flows through the gun and out the nozzle
![Page 38: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/38.jpg)
GMAW Parts
![Page 39: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/39.jpg)
GMAW Key Parts• Gun Housing: Holds or houses the welding wire liner, gas line,
and trigger in one piece• Conductor Tube: The angled part of the gun that the wire and
shielding gas flow through during the weld operation• Gas Diffuser: Disperses the shielding gas onto the weldment• Contact Tip: The part where the welding wire runs through.
Different sized tips accommodate different sized wire.• Nozzle: The cover for the end of the gun that keeps spatter
from sticking to the contact tip and gas diffuser and plugging the gun up.
![Page 40: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/40.jpg)
GMAW Process
Electrode
Arc
Shielding Gas
Puddle
Solidified Weld Metal
Welding Tip: Generally, drag on thin sheet metal and push on thicker materials
![Page 41: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/41.jpg)
GMAW Electrode
• A GMAW electrode is:– A metal wire – Fed through the gun by the wire feeder – Measured by its diameter
GMAW electrodes are commonly packaged on spools, reels and coils ranging from 1lb to 1000lbs
![Page 42: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/42.jpg)
GMAW Arc
• An electric arc occurs in the gas filled space between the electrode wire and the work piece
Electric arcs can generate temperatures up to 10,000°F
![Page 43: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/43.jpg)
GMAW Weld Puddle•As the wire electrode and work piece heat up and melt, they form a pool of molten material called a weld puddle•This is what the welder watches and manipulates while welding
![Page 44: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/44.jpg)
Shielding Gas•GMAW welding requires a shielding gas to protect the weld puddle •Shielding gas is usually CO2, argon, or a mixture of both
![Page 45: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/45.jpg)
Final Weld•The welder “lays a bead” of molten metal that quickly solidifies into a weld•The resulting weld is slag free
![Page 46: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/46.jpg)
• GOAL - Make Good Welds
• Eliminate Porosity
Eliminate Ropey Convex bead
Eliminate Excessive Spatter
Weld Examples
![Page 47: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/47.jpg)
OXY ACETYLENE
SET-UP
![Page 48: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/48.jpg)
Terms and Definitions
• Backfire: A short pop of the torch flame followed by extinguishing of the flame or continued burning of the gases.
• Flashback: when the torch flame moves into or beyond the mixing chamber.
• Preheating: Heating prior to a welding or cutting operation
![Page 49: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/49.jpg)
Equipment Required
• Oxygen cylinder• Acetylene cylinder• Pressure regulators• Two hoses encased together• Welding torch with tips• Welding goggles and safety glasses• Striker• Check valves to prevent flashback
![Page 50: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/50.jpg)
Acetylene Regulator
![Page 51: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/51.jpg)
Oxygen Regulator
![Page 52: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/52.jpg)
Typical Torch
![Page 53: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/53.jpg)
Torch Parts
![Page 54: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/54.jpg)
Striker
![Page 55: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/55.jpg)
Cutting Tip
![Page 56: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/56.jpg)
Welding and Heating Tips
![Page 57: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/57.jpg)
Check Valves
![Page 58: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/58.jpg)
Safety Rules for Oxy-Acetylene Workplace
• Keep the work area free of grease, oil, and flammable materials
• Cool or quench hot metal and extinguish all sparks before leaving. Sparks can travel up to 35 feet.
• Don’t leave torches, or hot metal where someone will pick them up
• Never carry matches or lighters into any work area
![Page 59: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/59.jpg)
Pressure Gauge Failure
![Page 60: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/60.jpg)
Cracked Acetylene Hose
![Page 61: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/61.jpg)
Improper Storage of Tanks
![Page 62: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/62.jpg)
Oxygen/ Acetylene Cutting Torch Stored on Unsafe Cart
![Page 63: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/63.jpg)
Oxygen/ Acetylene Cutting Torch Stored in Flammable Liquids Cabinet
![Page 64: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/64.jpg)
Regulator Parts
Pressure regulators reduce the supply pressure, indicated by the high pressure gauge to suitable working pressure, indicated by the low pressure gauge. By turning the adjusting screw, proper working pressures can be achieved.
![Page 65: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/65.jpg)
Personal Safety• Shirts– keep collar and sleeves buttoned to keep out sparks. Avoid
wearing shirts with pockets.• Pants or Coveralls– no cuffs and come over shoe tops
• Shoes– leather, cover entire foot
• Gloves– Leather, never use to pick up metal
• Safety Glasses – worn under helmets and goggles and all times.
![Page 66: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/66.jpg)
Eye Protection
• Wear safety glasses at all times• Wear welding goggles or a face shield with a
lens no. 4-6 while using torch equipment– when in doubt start with too dark of a lens and
then switch to a lighter one.
![Page 67: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/67.jpg)
Color Codes
• Green = Oxygen• Red = Acetylene
![Page 68: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/68.jpg)
Pressure Regulating Valves
• Each regulator has two gauges mounted on a single manifold. One indicates cylinder pressure and the other indicates working pressure for the torch.
• Each regulator has an adjusting screw or T-screw, so pressure to the torch can be quickly controlled by turning the screw righty-tighty to increases pressure and left-loosey to decrease pressure.
![Page 69: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/69.jpg)
Regulator Attachment
– Acetylene connectors have a V-groove left handed thread
– Oxygen connectors have a plain surface right handed thread
![Page 70: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/70.jpg)
PSI Settings
• Acetylene = 15 psi. max– Over 15 psi. can be fatal– Our regulators in the NCWHS lab will be set at 10
psi. max.• Oxygen = 40 psi. max– Over 40 psi. will dilute the heat of the flame– Our regulators in the NCWHS lab will be set at 30
psi. max.
![Page 71: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/71.jpg)
Torch Parts
• Torch body is the part of the torch that is held like a pencil. It contains two needle valves to control the flow of gas
• The welding head contains a mixer, mixing throat, and the welding tip
![Page 72: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/72.jpg)
Types of Flames
• Oxidizing– Excess oxygen with no feather, makes hissing
sound. Sounds like an angry snake.– Least used for anything
• Neutral– Burns equal amounts of oxygen and acetylene and
has a clear edged inner cone– Most used
![Page 73: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/73.jpg)
Types of Flames
• Carburizing– Excess acetylene with an acetylene feather two to
three times the length of the inner cone– While burning it will produce a heavy black smoke
flame– Used some in hardsurfacing, adds carbon to metal
![Page 74: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/74.jpg)
Operation Safety
• 1. Before you start make sure personal safety is followed.
• 2. Make sure you have had instruction• 3. Release adjusting screw on regulators
before opening valves• 4. Stand on the opposite side of the regulator
when opening a valve• 5. Open cylinder valve slowly, oxygen first all
the way open acetylene just a quarter of a turn
![Page 75: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/75.jpg)
Operation Safety (II)• 6. Do not use or compress acetylene at pressures higher
than 15 psi.• 7. Set working pressures as desired.
– Acetylene: 10 psi for NCWHS lab– Oxygen: 30 psi for NCWHS lab
• 8. Light acetylene first 9. Never use oil on regulators or any equipment– If oil mixes or touches the acetylene it will combust
• 10. Do not use compressed air as a substitute for oxygen• 11. Keep heat, flames, and sparks away from
combustibles.• 12. Keep hoses out of sparks or spatter to prevent leaks
![Page 76: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/76.jpg)
Safety Lighting the Torch• Check the torch valves to make sure they are closed• Open the oxygen tank valve full open• Open the acetylene tank valve ¼ turn• Turn on the oxygen knob on the torch body
– This is located next to the acetylene knob• Turn the acetylene gas on no more than ¼ turn• Strike and light• Mix oxygen into the flame with the mixing knob on the torch body.
While mixing you want to create a neutral flame. Press down on the cutting lever also to make sure the flame does not jump. – The mixing knob is located half-way up the torch body next to the cutting
lever
![Page 77: Arc Welding](https://reader033.vdocuments.us/reader033/viewer/2022061610/5681676e550346895ddc56a3/html5/thumbnails/77.jpg)
Shutting down the unit• Shut down the flame by turning off the acetylene knob on the
torch body.• Close the oxygen mixing knob located half-way up the torch
body• Shut off the tanks by closing the tank valves• Open the acetylene to purge or bleed the line• When both gauges read zero, close the valve• Open the oxygen valve• When both gauges read zero, close the valve• Release pressure on the regulators by turning adjusting screw
left or T-screw (out). DO NOT remove the T-screw• Coil hoses and put tools away