anti theft system using mems
DESCRIPTION
ANTI THEFT SYSTEM USING MEMSTRANSCRIPT
M.MANIKANTA [12KF1A0403]I.VISHAL KUMAR [12KF1A0401]P.RATNA KISHORE [12KF1A0406]
ANTI THEFT ALERT FOR STATIONARY GADGETS USING
WIRELESS TECHNOLOGYPresented by
Under the Guidance of Ms. P. BABY SHAMILI
MENTEY PADMANABHAM COLLEGE OF ENGINEERING AND TECHNOLOGY
ABSTRACT
• Present Security systems are done with mechanical switches which initiate an alarm when a certain preset level of motion is detected.
• This project overcomes the drawbacks of present security systems.
• This project can provide the security by using MEMS sensors with the help of embedded technology.
• Now a days everyone knows what type of security we need, security is needed for all the valuable devices.
• But even after taking care we are still unsatisfied with the security. Because Robbery of the devices has been increased widely.
• So as the technology is growing we are implementing new ideas over security purpose.
INTRODUCTION
BLOCK DIAGRAM
AT89S52 MICRO
CONTROLLER
POWER SUPPLY
GPS MODEM
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
KIT
BLOCK DIAGRAM
AT89S52 MICRO
CONTROLLER
POWER SUPPLY
GPS MODEM
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
KIT
POWER SUPPLY
• Step Down transformer converts high-voltage, low-current power into low-voltage, high-current power.
• Bridge Rectifier is used for converting an alternating current into a direct current.
• The output of the rectifier pulsating in nature. The unwanted ripple components are removed by placing filter circuit at the output of the rectifier.
• The Voltage Regulator is used to keep the output voltage constant at the desired value.
STEP DOWNT / F
BRIDGERECTIFIER FILTER VOLTAGE
REGULATOR
BLOCK DIAGRAM
AT89S52 MICRO
CONTROLLER
POWER SUPPLY
GPS MODEM
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
KIT
MICROCONTROLLER
• The AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller with 8K bytes of in-system programmable Flash memory.
• The device is manufactured using Atmel’s high-density nonvolatile memory technology.
• The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer.
12
MICRO CONTROLLER
PIN configuration :
BLOCK DIAGRAM
AT89S52 (8051) MICRO
CONTROLLER
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
POWER SUPPLY
GPS MODEM
KIT
MEMS
• MEMS stands for Micro Electro Mechanical System. It is fabricated using micro machining technology.
• It is used for sensing, actuation or are passive micro-structures.
• It is usually integrated with Electronic circuitry for control and/or information processing.
BLOCK DIAGRAM
AT89S52 (8051) MICRO
CONTROLLER
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
POWER SUPPLY
GPS MODEM
KIT
18
MAX-232
• The MAX232 is an Integrated Circuit first created in 1987 by Maxim Integrated Products.
• The MAX232 is a dual driver or receiver and typically converts the RX, TX, CTS and RTS signals.
• It Is Used In Battery-Powered Systems, Terminals, Modems, Computer and many other applications.
BLOCK DIAGRAM
POWER SUPPLY
AT89S52 (8051) MICRO
CONTROLLER
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
GPS MODEM
KIT
GSM (Global System for Mobile communication)
• GSM is a digital mobile telephone system.
• The GSM module is communicate the microcontroller with
mobile phones through UART.
• GSM modem interfacing with microcontroller for SMS
control of industrial equipment.
BLOCK DIAGRAM
POWER SUPPLY
GPS MODEM
AT89S52 (8051) MICRO
CONTROLLER
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
KIT
GPS(Global Positioning System)
• The Global Positioning System (GPS) is a space based satellite navigation system that provides location.
• The serial data from the GPS receiver is taken by using the Serial Interrupt of the controller.
BLOCK DIAGRAM
POWER SUPPLY
AT89S52 (8051) MICRO
CONTROLLER
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
GPS MODEM
KIT
LCD (Liquid Crystal Display)
• LCD is a flat panel display, electronic visual display that
uses the light modulation properties of liquid crystals.
• Liquid crystals do not emit light directly.
• LCDs are available to display arbitrary images or fixed
images which can be displayed or hidden.
BLOCK DIAGRAM
POWER SUPPLY
AT89S52 (8051) MICRO
CONTROLLER
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
GPS MODEM
KIT
BUZZER
• Piezo Electric buzzers are Solid state devices that produce
an Audible signal when powered.
• They are basically made up of piezo crystal.
• A simple oscillator circuit is used to make these signals
audible.
BLOCK DIAGRAM
AT89S52 (8051) MICRO
CONTROLLER
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
POWER SUPPLY
GPS MODEM
KIT
RESET
• RESET is an active High input When RESET is set to
High, 8051 goes back to the power on state.
• The 8051 is reset by holding the RST high for at least
two machine cycles.
BLOCK DIAGRAM
AT89S52 (8051) MICRO
CONTROLLER
MAX 232
GSM MODEM
BUZZER
DC MOTOR
USER MOBILE
MEMS SENSOR
16X2 LCD
RESET
POWER SUPPLY
GPS MODEM
KIT
DC MOTOR
• DC motor is an electrical machine which converts
direct current (electrical energy) into mechanical
energy.
• We use this DC motor in this project for checking the
Direct current.
PROPOSED METHOD
• If the theft is not done then the fan rotates continuously. It is the
indication of the power supply.
• When the MEMS sensor direction is changed then the fan is OFF
and the buzzer will ON.
• At that time message will be send to user mobile by the GSM
module and GPS module.
RESULT
RESULT FROM GPS & GSM
APPLICATIONS
• Apartments.
• Tollgates.
• Industries & Companies.
• Security places.
• Museums.
• Jewelry Shops.
ADVANTAGES
•Safe & secure.
•Easy to use.
•Reduce the Theft.
•Reduce the Man Power.
•Theft can caught easily.
DISADVANTAGES
• If we are not having the signal, then the
information will not be sent.
• The kit must be in the network coverage area.
CONCLUSION
• By using this anti theft, robberies of the valuable
devices can overcome, the theft can be caught easily.
• With the development of sensor technology, MEMS
sensors in the form will be varied, through the
extensive application of electronic technology to
achieve high overall performance further.
FUTURE SCOPE
• The future scope of our project is that a new anti-theft sensor system
is being developed at the advanced institute of industrial technology.
• Presently only SMS feature is available, we can include the call
feature for case of operation.
• Microphone could be interfaced to the GSM/GPS module so that
during theft activity voice call could be established with the owned.
REFERENCES
• http://www.alarmscctv.com/detectionprodint6.html
• http://www.societyofrobots.com/microcontroller_tutorial.shtml
• http://www.nowsms.com/faq/what-is-a-gsm-modem
• http://www.vexrobotics.com/276-2153.html
• http://www.adc.com/Americas/en_US/1268116694636
Thank you
Any quires?