annexure i for specifications of stands and tanks

7/28/2019 Annexure i for Specifications of Stands and Tanks

1/6

ANNEXURE - I

SPECIFICATIONS OF STANDS AND TANKS

BIDDERS RESPONSE BIDDERS REMARKS

COMPLIED / NOT

COMPLIED

Load / Unload StandMOC : MS structural, two coats epoxy painted 02 nos

Inside dimensions, mm : 1400 x 800 x 1000 H

Construction : 3 mm thick MS sheet with external reinforcement of MS

Leg : MS Channel 100 x 50, epoxy base painted, along 1400mm

Operating media : Hot alkali solution

Operating temperature : 80 deg C

Insulation: 40mm thick glass wool on sand blasted outside surface

backed by 3 mm thick flexible FRP sheet cladding

Heaters : 7.5 kw/230 V/SS-304 :4 nos

Lip exhaust: PPGL /FRP construction on two longitudinal sides

Sensor : One no. at a corner of the tank encased in a SS 316 tube

Digital Temp controller: Shall be installed in the control panel, to control the operation

of the heaters in the tank

V blocks : 2 nos. PP for each tankDrain outlet : 1 in. PP ball valve

Inside dimensions, mm : 1400 x 700/800 x 1000 H

Construction : 15 mm imported Rochiling brand PP sheet external MStubular reinforcement having PP covering & additional PP ribs.

2.Cold swill Tank 09 Nos.

1.Alkaline Degreasing Tank 02 nos

Note: If there are any deviations from the tendered specifications please mention in remarks column.

1


2/6

ANNEXURE - I



COMPLIED / NOT

COMPLIED

Leg : MS channel 100 x 50, epoxy base painted, along 1400 mm.

Operating media : Rinse water

Level controller : Magnetic float switch type p of PP

V blocks : 2 nos. PP of each tank

Water inlet : 3/4 in. PVC ball valve

Drain outlet : 1 in. PVC ball valve.


Construction

: 15 mm imported Rochiling brand PP sheet, external MS

tubular reinforcement having PP covering & additional PP

ribs.

Leg : MS channel 100 x 50, epoxy base painted, along 1400 mm

Level controller : Magnetic float switch type, of PP

Operating media : Acid base (nitric acid/NaOH)

Operating temperature: Room

Lip exhaust : PPGL /FRP construction on two longitudinal sides


Water inlet : 3/4 in. PVC ball valve

Drain outlet : 1 in. PVC ball valve

3.Brightening/pickling Tank 02 No.


2


3/6

ANNEXURE - I



COMPLIED / NOT

COMPLIED


Construction : 20 mm imported Rochiling brand PP sheet, external MS

tubular reinforcement having PP covering & additional PP rib.

Leg : MS Channel 150 x 100 epoxy base painted

Operating media : Sulphuric acid

Operating temperature : (-) 8 to (-) 10 deg C

Cooling coil : Titanium Gr-2,16 mm OD 1.6 mm thk for heat transfer

Insulation : 75 mm thick Thermocole / PUF backed by 3 mm thick

flexible FRP sheet cladding

Lip exhaust : PPGL /FRP construction on two longitudinal sides & one

width side at the rear

sensor: One no. at a corner of the tank encased in a Ti tube the heaters

in the tank

Contact saddles : Copper with provision to connect to Rectifier

Bus bar : 30 x 10 x 1800 mm electrolytic copper : 2 nos each to beconnected to rectifier supply

Cathode : Lead electrode with copper fastener

Flight bars : as per the requirement (Copper:100% conductivity)

V blocks : 2 nos. of each tank copper with 100% conductivity

4. Anodisation Process Tank 02 Nos.


3


4/6

ANNEXURE - I



COMPLIED / NOT

COMPLIED


Construction : 3 mm thick SS 304 sheet with external reinforcement of MS


Operating media : Hot water

Operating temperature : 70 80 deg C

Insulation: 40mm thick glass wool on sand blasted outside surface backed

by 3 mm thick flexible FRP sheet cladding

Heaters : 7.5 kw/230 V/SS-304 : 4 nos

Sensor : One no. at a corner of the tank encased in a SS 316 tube

Digital Temp controller : Shall be installed in the control panel, to control the operationof the heaters in the tank

V blocks : 2 nos. PP

Drain outlet : 1 in. PP ball valve

Control panel : Houses safety gears for the heaters


Construction : 3 mm thick SS 304 sheet with external reinforcement of MS


Operating media : potassium dichromate.


5.Hot Rinse Tank 02 no.

6.Passivation tank 02 No.


4


5/6

ANNEXURE - I



COMPLIED / NOT

COMPLIED

Insulation : 40mm thick glass wool on sand blasted outside surface backed

by 3 mm thick flexible FRP sheet cladding

Heaters : 7.5 kw/230 V/titanium : 4 nos

Sensor : One no. at a corner of the tank encased in a SS 316 tube the

heaters in the tank

V blocks: 2 nos. PP of each tank


Control panel : Houses safety gears for the heaters


Maximum temperature : 90 deg C

Construction (inside to out side)

:3MM thick SS 316 sheet suitably reinforcement of MS and

complete with 40 mm thick glass wool insulation encased in 14

SWG GI sheet which is further covered externally covered with

5 mm FRP coating

Seating: 2 MS channel 100X50 mm with FRP coated, along withlength (1400MM), it is to be painted with anti corrosive epoxy

paint.

Operating media : zinc phosphate.


Insulation: 40mm thick glass wool on sand blasted outside surface

backed by 3 mm thick flexible FRP sheet cladding

7. Phospating tanks - 02 nos.


5


6/6

ANNEXURE - I



COMPLIED / NOT

COMPLIED

Heaters : 7.5 kw/230 V/titanium : 4 nos

Sensor : One no. at a corner of the tank encased in a SS 316 tube the

heaters in the tank



Inside dimensions, mm : 1400 x 700 x 1000(as per the site requirement)

Maximum temperature : 90 deg C

Casing : Inner 1.6 mm CRCA

Outer 1.2 mm CRCA

Insulation : Ceramic wool of 75 mm in the gap between the inner and

outer walls, including the hinged door at the top

Heating : 7.5 kw/230 V/SS/titanium (party may indicate the MOC &

qty)

Air circulation : Blower with motor provided

Painting : Inner chamber - Heat resistant Al. paint

: Exterior - Anti corrosive grey

NOTE: PARTY HAS TO VISIT THE SITE (BDL,BHANUR) BEFORE QUOTE.

8. Hot Air Dryer One No.


6

annexure i for specifications of stands and tanks

Documents