FACTS Conceptand General System

Considerations1.1 TRANSMISSION INTERCONNECTIONS

Most if not all of the world's electric power supply systems are widely interconnected,involving connections inside utilities' own territories which extend to inter-utilityinterconnections and then to inter-regional and international connections. This is donefor economic reasons, to reduce the cost of electricity and to improve reliability ofpower supply.

1.1.1 Why We Need Transmission Interconnections

We need these interconnections because, apart from delivery, the purpose ofthe transmission network is to pool power plants and load centers in order to minimizethe total power generation capacity and fuel cost. Transmission interconnections enabletaking advantage of diversity of loads, availability of sources, and fuel price in orderto supply electricity to the loads at minimum cost with a required reliability. In general,if a power delivery system was made up of radial lines from individual local generatorswithout being part of a grid system, many more generation resources would be neededto serve the load with the same reliability, and the cost of electricity would be muchhigher. With that perspective, transmission is often an alternative to a new generationresource. Less transmission capability means that more generation resources wouldbe required regardless of whether the system is made up of large or small powerplants. In fact small distributed generation becomes more economically viable if thereis a backbone of a transmission grid. One cannot be really sure about what the optimumbalance is between generation and transmission unless the system planners use ad-vanced methods of analysis which integrate transmission planning into an integratedvalue-based transmission/generation planning scenario. The cost of transmission linesand losses, as well as difficulties encountered in building new transmission lines, wouldoften limit the available transmission capacity. It seems that there are many caseswhere economic energy or reserve sharing is constrained by transmission capacity,and the situation is not getting any better. In a deregulated electric service environment,an effective electric grid is vital to the competitive environment of reliable electricservice.

Chapter 1 f FACTS Concept and General System Considerations

On the other hand, as power transfers grow, the power system becomes increas-ingly more complex to operate and the system can become less secure for ridingthrough the major outages. It may lead to large power flows with inadequate control,excessive reactive power in various parts of the system, large dynamic swings betweendifferent parts of the system and bottlenecks, and thus the full potential of transmissioninterconnections cannot be utilized.

The power systems of today, by and large, are mechanically controlled. Thereis a widespread use of microelectronics, computers and high-speed communicationsfor control and protection of present transmission systems; however, when operatingsignals are sent to the power circuits, where the final power control action is taken,the switching devices are mechanical and there is little high-speed control. Anotherproblem with mechanical devices is that control cannot be initiated frequently, becausethese mechanical devices tend to wear out very quickly compared to static devices.In effect, from the point of view of both dynamic and steady-state operation, thesystem is really uncontrolled. Power system planners, operators, and engineers havelearned to live with this limitation by using a variety of ingenious techniques to makethe system work effectively, but at a price of providing greater operating margins andredundancies. These represent an asset that can be effectively utilized with prudentuse of FACTS technology on a selective, as needed basis.

In recent years, greater demands have been placed on the transmission network,andthese demandswill continue to increasebecause of the increasingnumberof nonutil-ity generators and heightened competition among utilities themselves. Added to this isthe problem that it is very difficult to acquire new rights of way. Increased demands ontransmission, absence of long-term planning, and the need to provide open access togenerating companies and customers, all together have created tendencies toward less

security and reduced quality of supply. The FACTS technology is essential to alleviatesome but not all of these difficulties by enabling utilities to get the most service fromtheir transmission facilities and enhance grid reliability. It must be stressed, however,that formany of the capacity expansion needs, building of newlines or upgradingcurrentand voltage capability of existing lines and corridors will be necessary.

1.1.2 Opportunities for FAGTS

What is most interesting for transmission planners is that FACTS technologyopens up new opportunities for controlling power and enhancing the usable capacityof present, as well as new and upgraded, lines. The possibility that current through a

line can be controlled at a reasonable cost enables a large potential of increasing thecapacity of existing lines with larger conductors, and use of one of the FACTS Control-lers to enable corresponding power to flow through such lines under normal andcontingency conditions.

These opportunities arise through the ability of FACTS Controllers to controlthe interrelated parameters that govern the operation of transmission systems includingseries impedance, shunt impedance, current, voltage, phase angle, and the dampingof oscillations at various frequencies below the rated frequency. These constraintscannot be overcome, while maintaining the required system reliability, by mechanicalmeans without lowering the useable transmission capacity. By providing added flexibil-ity, FACTS Controllers can enable a line to carry power closer to its thermal rating.Mechanical switching needs to be supplemented by rapid-response power electronics.It must be emphasized that FACTS is an enabling technology, and not a one-on-onesubstitute for mechanical switches.

Section 1,.2 I Flow of Power in an AC Svstem

The FACTS technology is not a single high-power Controller, but rather acollection of Controllers, which can be applied individually or in coordination withothers to control one or more of the interrelated system parameters mentioned above.A well-chosen FACTS Controller can overcome the specific limitations of a designatedtransmission line or a corridor. Because all FACTS Controllers represent applicationsof the same basic technology, their production can eventually take advantage oftechnologies of scale. Just as the transistor is the basic element for a whole variety ofmicroelectronic chips and circuits, the thyristor or high-power transistor is the basicelement for a variety of high-power electronic Controllers.

FACTS technology also lends itself to extending usable transmission limits in astep-by-step manner with incremental investment as and when required. A plannercould foresee a progressive scenario of mechanical switching means and enablingFACTS Controllers such that the transmission lines will involve a combination ofmechanical and FACTS Controllers to achieve the objective in an appropriate, stagedinvestment scenario.

Some of the Power Electronics Controllers, now folded into the FACTS conceptpredate the introduction of the FACTS concept by co-author Hingorani to the technicalcommunity. Notable among these is the shunt-connected Static VAR Compensator(SVC) for voltage control which was first demonstrated in Nebraska and commercial-ized by GE in 1974 and by Westinghouse in Minnesota in 1975. The first series-connected Controller, NGH-SSR Damping Scheme, invented by co-author Hingorani,a low power series capacitor impedance control scheme, was demonstrated in Califor-nia by Siemens in 1984. It showed that with an active Controller there is no limitto series capacitor compensation. Even prior to SVCs, there were two versions ofstatic saturable reactors for limiting overvoltages and also powerful gapless metaloxide arresters for limiting dynamic overvoltages. Research had also been undertakenon solid-state tap changers and phase shifters. However, the unique aspect ofFACTS technology is that this umbrella concept revealed the large potentialopportunity for power electronics technology to greatly enhance the value of powersystems, and thereby unleashed an array of new and advanced ideas to make ita reality. Co-author Gyugyi has been at the forefront of such advanced ideas.FACTS technology has also provided an impetus and excitement perceived by theyounger generation of engineers, who will rethink and re-engineer the future powersystems throughout the world.

It is also worth pointing out that, in the implementation of FACTS technology,we are dealing with a base technology, proven through HVDC and high-powerindustrial drives. Nevertheless, as power semiconductor devices continue to improve,particularly the devices with turn-off capability, and as FACTS Controller conceptsadvance, the cost of FACTS Controllers will continue to decrease. Large-scale useof FACTS technology is an assured scenario.

1.2 FLOW OF POWER IN AN AC SYSTEM

At present, many transmission facilities confront one or more limiting network parame-ters plus the inability to direct power flow at will.

In ac power systems, given the insignificant electrical storage, the electricalgeneration and load must balance at all times. To some extent, the electrical systemis self-regulating. If generation is less than load, the voltage and frequency drop, andthereby the load, goes down to equal the generation minus the transmission losses.However, there is only a few percent margin for such a self-regulation. If voltage is

Chapter 1 f FACTS Concept and General System Considerations

propped up with reactive power support, then the load will go up, and consequentlyfrequency will keep dropping, and the system will collapse. Alternately, if there is

inadequate reactive power, the system can have voltage collapse.

When adequate generation is available, active power flows from the surplusgeneration areas to the deflcit areas, and it flows through all parallel paths available

which frequently involves extra high-voltage and medium-voltage lines. Often, long

distances are involved with loads and generators along the way. An often cited example

is that much of the power scheduled from Ontario Hydro Canada to the North East

United States flows via the PJM system over a long loop, because of the presence ofa large number of powerful low impedance lines along that loop. There are in fact

some major and a large number of minor loop flows and uneven power flows in anypower transmission system.

1.2.1 Power Flow in Parallel Paths

consider a very simple case of power flow [Figure 1.1(a)], through two parallelpaths (possibly corridors of several lines) from a surplus generation area, shown as

an equivalent generator on the left, to a deficit generation area on the right. Withoutany control, power flow is based on the inverse of the various transmission line

impedances. Apart from ownership and contractual issues over which lines carry howmuch power, it is likely that the lower impedance line may become overloaded and

thereby limit the loading on both paths even though the higher impedance path is notfully loaded. There would not be an incentive to upgrade current capacity of the

overloaded path, because this would further decrease the impedance and the invest-

ment would be self-defeating particularly if the higher impedance path already has

enough capacity.Figure 1.1(b) shows the same two paths, but one of these has HVDCtransmission.

With HVDC, power flows as ordered by the operator, because with HVDC power

electronics converters power is electronically controlled. Also, because power is elec-

tronically controlled, the HVDC line can be used to its full thermal capacity if adequate

converter capacity is provided. Furthermore, an HVDC line, because of its high-speed

control, can also help the parallel ac transmission line to maintain stability. However,HVDC is expensive for general use, and is usually considered when long distances

are involved, such as the Pacific DC Intertie on which power flows as ordered bythe operator.

As alternative FACTS Controllers, Figures 1.1(c) and 1.1(d) show one of thetransmission lines with different types of series type FACTS Controllers. By means

of controlling impedance [Figure 1.1(c)] or phase angle [Figure 1.1(d)], or series

injection of appropriate voltage (not shown) a FACTS Controller can control thepower flow as required. Maximum power flow can in fact be limited to its rated limitunder contingency conditions when this line is expected to carry more power due tothe loss of a parallel line.

1.2.2 Power Flow in a Meshed SYstem

To further understand the free flow of power, consider a very simplified case in

which generators at two different sites are sending power to a load center through a

network consisting of three lines in a meshed connection (Figure 1.2). Suppose the

lines AB, BC, and AC have continuous ratings of 1000 Mw, 1250 MW, and 2000

MW, respectively, and have emergency ratings of twice those numbers for a sufficient

Section 1.2 I Flow of Power in an AC Svstem

SurplusGeneration Area

Figure 1-.1 Power flowpower flowimpedance;

lmpedefic€ = X

E*eE 2t3

lmpedenc€ = 2X

E*.= 113

HV dc line

E*otro*6omir.o

Variable impedence

E*er rro* iForsireo

Variable phase angle

Power flow as desired

in parallel paths: (a) ac power flow with parallel paths; (b)control with HVDC; (c) power flow control with variable(d) power flow control with variable phase angle.

Load Load

Chapter 1 f FACTS Concept and General System Considerations

length of time to allow rescheduling of power in case of loss of one of these lines. IfonJof the generators is generating 2000 MW and the other 1000 MW, a total of 3000

MW would be deliveredio the load center. For the impedances shown, the three lines

would carry 600, 1600, and L400 Mw, respectively, as shown in Figure 1'.2(a). Such a

situation would overload line BC (loaded at 1600 MW for its continuous rating of

1250 MW), and therefore generation would have to be decreased at B, and increased

at A. in order to meet the load without overloading line BC'power, in short, flows in accordance with transmission line series impedances

(which are 907o inductive) that bear no direct relationship to transmission ownership,

contracts, thermal limits, or transmission losses.

If, however, a capacitor whose reactance is -5 ohms (O) at the synchronous

frequency is inserted in one line [Figure 1.2(b)], it reduces the line's impedance from

L0 o to j,f}, ro that power flow through the lines AB, BC, and AC will be 250,1250,

and 1750 MW, respectively. It is clear that if the series capacitor is adjustable, then

other power-flow levels may be realized in accordance with the ownership, contract,

thermil limitations, transmission losses, and a wide range of load and generation

schedules. Although this capacitor could be modular and mechanically switched, the

number of operations would be severely limited by wear on the mechanical components

because the line loads vary continuously with load conditions, generation schedules,

and line outages.Other complications may arise if the series capacitor is mechanically controlled.

A series capacitor in a line may lead to subsynchronous resonance (typically at 10-50

Hz for a OOgzsystem). This resonance occurs when one of the mechanical resonance

frequencies of tle shaft of a multiple-turbine generator unit coincides with 60 Hz

-5Ct

2000 MW 3000 MWload

\e1000 MW

(d)

Figure L.2 power flow in a mesh network: (a) system diagram; (b) system diagram

with Thyristor-Controlled Series Capacitor in line AC; (c) system dia-

gram with Thyristor-Controlled Series Reactor in line BC; (d) system

diagram with Thyristor-Controlled Phase Angle Regulator in line AC.

(c)

1000 MW

Section 1.3 I What Limits the Loading Capability?

minus the electrical resonance frequency of the capacitor with the inductive impedanceof the line. If such resonance persists, it will soon damage the shaft. Also while theoutage of one line forces other lines to operate at their emergency ratings and carryhigher loads, power flow oscillations at low frequency (typically 0.3-3 Hz) may causegenerators to lose synchronism, perhaps prompting the system's collapse.

If all or a part of the series capacitor is thyristor-controlled, however, it can bevaried as often as required. It can be modulated to rapidly damp any subsynchronousresonance conditions, as well as damp low frequency oscillations in the power flow.This would allow the transmission system to go from one steady-state condition toanother without the risk of damage to a generator shaft and also help reduce the riskof system collapse. In other words, a thyristor-controlled series capacitor can greatlyenhance the stability of the network. More often than not though, it is practical forpart of the series compensation to be mechanically controlled and part thyristorcontrolled, so as to counter the system constraints at the least cost.

Similar results may be obtained by increasing the impedance of one of the linesin the same meshed configuration by inserting a7 A reactor (inductor) in series withline AB [Figure L2(c)1. Again, a series inductor that is partly mechanically and partlythyristor-controlled, it could serve to adjust the steady-state power flows as well as

damp unwanted oscillations.As another option, a thyristor-controlled phase-angle regulator could be installed

instead of a series capacitor or a series reactor in any of the three lines to serve thesame purpose. In Figure 7.2(d), the regulator is installed in the third line to reducethe total phase-angle difference along the line from 8.5 degrees to 4.26 degrees. Asbefore, a combination of mechanical and thyristor control of the phase-angle regulatormay minimize cost.

The same results could also be achieved by injecting a variable voltage in oneof the lines. Note that balancing of power flow in the above case did not require morethan one FACTS Controller, and indeed there are options of different controllers andin different lines.

If there is only one owner of the transmission grid, then a decision can be madeon consideration of overall economics alone. On the other hand, if multiple ownersare involved, then a decision mechanism is necessary on the investment and ownership.

1,3 WHAT LIMITS THE LOADING CAPABILITY?

Assuming that ownership is not an issue, and the objective is to make the best use ofthe transmission asset, and to maximize the loading capability (taking into accountcontingency conditions), what limits the loading capability, and what can be doneabout it?

Basically, there are three kinds of limitations:

r Thermalr Dielectricr Stability

Thermal Thermal capability of an overhead line is a function of the ambienttemperature, wind conditions, condition of the conductor, and ground clearance. Itvaries perhaps by a factor of 2 to 1 due to the variable environment and the loadinghistory. The nominal rating of a line is generally decided on a conservative basis,envisioning a statistically worst ambient environment case scenario. Yet this scenario

Chapter 1 f FACTS Concept and General System Considerations

occurs but rarely which means that in reality, most of the time, there is a lot morereal time capacity than assumed. Some utilities assign winter and summer ratings, yetthis still leaves a considerable margin to play with. There are also off-line computerprograms that can calculate a line's loading capability based on available ambientenvironment and recent loading history. Then there are the on-line monitoring devices

that provide a basis for on-line real-time loading capability. These methods have

evolved over a period of many years, and, given the age of automation (typified byGPS systems and low-cost sophisticated communication services), it surely makes

sense to consider reasonable, day to day, hour to hour, or even real-time capabilityinformation. Sometimes, the ambient conditions can actually be worse than assumed,

and having the means to determine actual rating of the line could be useful.

During planning/design stages, normal loading of the lines is frequently decidedon a loss evaluation basis under assumptions which may have changed for a varietyof reasons; however losses can be taken into account on the real-time value basis ofextra loading capability.

Of course, increasing the rating of a transmission circuit involves considerationof the real-time ratings of the transformers and other equipment as well, some ofwhich may also have to be changed in order to increase the loading on the lines. Real-

time loading capability of transformers is also a function of ambient temperature,

aging of the transformer and recent loading history. Off-line and on-line loading

capability monitors can also be used to obtain real time loading capability of transform-ers. Also, the transformer also lends itself to enhanced cooling.

Then there is the possibility of upgrading a line by changing the conductor tothat of a higher current rating, which may in turn require structural upgrading. Finally,there is the possibility of converting a single-circuit to a double-circuit line. Once the

higher current capability is available, then the question arises of how it should be

used. Will the extra power actually flow and be controllable? Will the voltage conditions

be acceptable with sudden load dropping, etc.? The FACTS technology can help inmaking an effective use of this newfound capacity.

Dielectric From an insulation point of view, many lines are designed very conser-

vatively. For a given nominal voltage rating, it is often possible to increase normaloperation by +10Vo voltage (i.e., 500 kV-550 kV) or even higher. Care is then needed

to ensure that dynamic and transient overvoltages are within limits. Modern gapless

arresters, or line insulators with internal gapless arresters, or powerful thyristor-con-trolled overvoltage suppressors at the substations can enable significant increase inthe line and substation voltage capability. The FACTS technology could be used toensure acceptable over-voltage and power flow conditions.

Stability There are a number of stability issues that limit the transmission capa-

bility. These include:

r Transient stabilityr Dynamic stabilityr Steady-state stabilityr Frequency collapser Voltage collapser Subsynchronous resonance

Excellent books are available on this subject. Therefore, discussion on these

topics in this book will be brief, and limited to what is really essential to the explanation

Section 1.4 I Flow and Stability Considerations of a Transmission Interconnection

of FACTS Controllers. The FACTS technology can certainly be used to overcome anyof the stability limits, in which case the ultimate limits would be thermal and dielectriC.

1.4 POWER FLOW AND DVNAMICSTABILITY CONSIDERATIONSOF A TRANSMISSION INTERCONNECTION

Figure 1.3(a) shows a simplified case of power flow on a transmission line. LocationsI and 2 could be any transmission substations connected by a transmission line.Substations may have loads, generation, or may be interconnecting points on thesystem and for simplicity they are assumed to be stiff busses. Er and E2 are themagnitudes of the bus voltages with an angle 6'between the two. The line is assumedto have inductive impedance X, and the line resistance and capacitance are ignored.

As shown in the phasor diagram [Figure 1.3(b)] the driving voltage drop in theIine is the phasor difference E1 between the two line voltage phasors, El and E2.Theline current magnitude is given by:

I : EylX, and lags Eyby 90"

It is important to appreciate that for a typical line, angle D and correspondingdriving voltage, or voltage drop along the line, is small compared to the line voltages.Given that a transmission line may have a voltage drop at full load of. perhaps lvol10 km, and assuming that a line between two stiff busbars (substations) is 200 kmlong, the voltage drop along this line would be 20Vo at full load, and the angle 6 wouldbe small. If we were to assume, for example, that with equal magnitudes of E1 and E2,and Xof 0.2 per unit magnitude, the angle dwould be only 0.2 radians or 11.5 degrees.

The current flow on the line can be controlled by controllingEyor Xor d. Inorder to achieve a high degree of control on the current in this line, the equipmentrequired in series with the line would not have a very high power rating. For example,a 500 kv (approximately 300 kv phase-ground), 2000 A line has a three-phasethroughput power of 1800 MVA, and, for a 200 km length, it would have a voltagedrop of about 60 kV. For variable series compensation of say,25Vo,the series equipmentrequired would have a nominal rating of 0.25 x 60 kv x 2000 A : 30 MVA perphase, or 90 MVA for three phases, which is only SVo of the throughput line ratingof 1800 MVA. Voltage across the series equipment would only be 15 kV at fullload, although it would require high-voltage insulation to ground (the latter is not asignificant cost factor). However, any series-connected equipment has to be designedto carry contingency overloads so that the equipment may have to be rated to 700Vooverload capability.

Nevertheless the point of this very simple example is that generally speakingthe rating of series FACTS Controllers would be a fraction of the throughput ratingof a line.

Figure 1.3(b) shows that the current flow phasor is perpendicular to the drivingvoltage (90'phase lag). If the angle between the two bus voltages is small, the currentflow largely represents the active power. Increasing or decreasing the inductive imped-ance of a line will greatly affect the active power flow. Thus impedance control, whichin reality provides current control, can be the most cost-effective means of controllinpttre powli flow. With appropriate control loops, it can be ur"O for fo*";;;;;;irjandior angle control for stability.

Figure 1.3(c), corresponding to Figure 1.3(b), shows a phasor diagram of the

10 Chapter L l FACTS Concept and General System Considerations

(b)

(E -E2cos6)

-Et sin 6 E2 cos {E'6

\lPt = E2 sin 6 lx

eElsin d

\ Ersin 6

6)t x / L(r, -E1cos6)E1 cos 6( \l*=(E - E2 cos

E1 cos 6 )/X1 80"

lqz= Ez-

(c) (d)

Et6rQa E,W

E,ryrt\

':E,W

Pmax

Et- Ez

njected voltage

4- Ez

Figure 1.3 Ac power flow control of a transmission line: (a) simple two-machine

system; (b) current flow perpendicular to the driving voltage; (c) active

and reactive power flow phasor diagram; (d) power angle curves for

different values of" X; (e) regulating voltage magnitude mostly changes

reactive power; (f) injecting voltage perpendicular to the line current

mostly changes active power; (f) injecting voltage phasor in series with

the line. (Note that for clarity the phasors are identified by their magni-

tudes in this figure.)

90'Angle 6

<- Injected voltage

-E2

lez= E1 sin 6 lx

, ='f' sin 6

Section 1.4 I Flow and Stability Considerations of a Transmission Interconnection 11

relationship between the active and reactive currents with reference to the voltagesat the two ends.

Active component of the current flow at E1 is:

Iot: (Ez sin 6)/X

Reactive component of the current flow at ,E1 is:

I,1: (Et - E2cos 6)lX

Thus, active power at the E1 end:

Pr : Er, (E2 sin 6)lX

Reactive power at the .81 end:

Qt: Et (Er - E2cos 6)lX

Similarly, active component of the current flow at E2 rs:

Ipz - (Et sin 6)/X

Reactive component of the current flow at E2 rs:

Iqz: (8, ,81 cos 6)lX

Thus, active power at the E2 end:

Pz: E, (E1 sin 6)lX

Reactive power at the E2 end:

Qz: E, (82 - E1 cos 6)lX

Naturally P1 and P2 a;re the same:

P - E, (E2 sin 6)lX

(1.1)

(r.2)

(1.3)

because it is assumed that there are no active power losses in the line. Thus, varying thevalue of Xwill vary P, Q6 and Q2in accordance with (1.1), (1.2), and (1.3), respectively.

Assuming that \ and E2 are the magnitudes of the internal voltages of the twoequivalent machines representing the two systems, and the impedance X includes theinternal impedance of the two equivalent machines, Figure 1.3(d) shows the half sine-wave curve of active power increasing to a peak with an increase in 6 to 90 degrees.Power then falls with further increase in angle, and finally to zero at 6 : 180'. It iseasy to appreciate that without high-speed control of any of the parameters Et Ez,Et - Ez, X and A the transmission line can be utilized only to a level well below thatcorresponding to 90 degrees. This is necessary, in order to maintain an adequatemargin needed for transient and dynamic stability and to ensure that the system doesnot collapse following the outage of the largest generator and/or a line.

Increase and decrease of the value of X will increase and decrease the heightof the curves, respectively, as shown in Figure 1.3(d). For a given power flow, varyingof X will correspondingly vary the angle between the two ends.

Power/current flow can also be controlled by regulating the magnitude of voltagephasor.El or voltage phasor E2. However, it is seen from Figure 1.3(e) that with changein the magnitude of .81, the magnitude of the driving voltage phasor Er - Ez does not

12 Chapter 1 f FACTS Concept and General System Considerations

change by much, but its phase angle does. This also means that regulation of the

-ugnitod" of voltage phasor E1 andlor E2has much more influence over the reactive

power flow than the active power flow, as seen from the two current phasors corre-

iponding to the two driving voltage phasors Et - Ez shown in Figure 1'3(e).

Current flow and hence power flow can also be changed by injecting voltage in

series with the line. It is seen from Figure 1.3(f) that when the injected voltage is in

phase quadrature with the current (which is approximately in phase with the driving

voltage, Figure 1.3(f), it directly influences the magnitude of the current flow, and

with small angle influences substantially the active power flow'Alternatively, the voltage injected in series can be a phasor with variable magni-

tude and phase relationship with the line voltage [Figure t.S(g)]. It is seen that varying

the amplitude and phase angle of the voltage injected in series, both the active and

reactive current flow can be influenced. Voltage injection methods form the most

important portfolio of the FACTS Controllers and will be discussed in detail in subse-

quent chaPters.

1.5 RELATIVE IMPORTANCE OFCONTROLLABLE PARAMETERS

With reference to the above discussion and Figure 1".3, it is worth noting a few basic

points regarding the possibilities of power flow control:

r Control of the line impedance X (e.g.,with a thyristor-controlled series capaci-

tor) can provide a powerful means of current control'

r When the angle is not large, which is often the case, control of X or the angle

substantially provides the control of active power.

I Control of angle (with a Phase Angle Regulator, for example), which in turn

controls the driving voltage, provides a powerful means of controlling the

current flow and hence active power flow when the angle is not large.

r Injecting a voltage in series with the line, and perpendicular to the current

flow, can increase or decrease the magnitude of current flow. Since the current

flow lags the driving voltage by 90 degrees, this means injection of reactive

power in series, (e.g., with static synchronous series compensation) can provide

i powerful means of controlling the line current, and hence the active power

when the angle is not large.

r Injecting voltage in series with the line and with any phase angle with respect

to the driving voltage can control the magnitude and the phase of the line

current. This means that injecting a voltage phasor with variable phase angle

can provide a powerful means of precisely controlling the active and reactive

po*Lt flow. This requires injection of both active and reactive power in series.

r Because the per unit line impedance is usually a small fraction of the line

voltage, the MVA rating of a series Controller will often be a small fraction

of the throughput line MVA.r When the angle is not large, controlling the magnitude of one or the other

line voltages (e.g., with a thyristor-controlled voltage regulator) can be a very

cost-effective means for the control of reactive power flow through the intercon-

nection.r Combination of the line impedance control with a series Controller and voltage

Basic Types of FACTS Controllers 13

regulation with a shunt Controller can also provide a cost-effective meanscontrol both the active and reactive power flow between the two systems.

1.6 BASIC TYPES OF FACTS CONTROLLERS

In general, FACTS Controllers can be divided into four categories:

I Series Controllerst Shunt ControllersI Combined series-series ControllersI Combined series-shunt Controllers

Figure L.4(a) shows the general symbol for a FACTS Controller: a thyristor arrowinside a box.

Series Controllers: lFigure l.a(b)] The series Controller could be a variableimpedance, such as capacitor, reactor, etc., or a power electronics based variable sourceof main frequency, subsynchronous and harmonic frequencies (or a combination) toserve the desired need. In principle, all series Controllers inject voltage in series withthe line. Even a variable impedance multiplied by the current flow through it, representsan injected series voltage in the line. As long as the voltage is in phase quadraturewith the line current, the series Controller only supplies or consumes variable reactivepower. Any other phase relationship will involve handling of real power as well.

Shunt Control/ers: [Figure 1.a(c)] As in the case of series Controllers, the shuntControllers may be variable impedance, variable source, or a combination of these.In principle, all shunt Controllers inject current into the system at the point of connec-tion. Even a variable shunt impedance connected to the line voltage causes a variablecurrent flow and hence represents injection of current into the line. As long as theinjected current is in phase quadrature with the line voltage, the shunt Controller onlysupplies or consumes variable reactive power. Any other phase relationship will involvehandling of real power as well.

Combined series-series Controllers: [Figure 1.4(d)] This could be a combinationof separate series controllers, which are controlled in a coordinated manner, in amultiline transmission system. Or it could be a unified Controller, Figure 1.4(d), inwhich series Controllers provide independent series reactive compensation for eachline but also transfer real power among the lines via the power tint. fne real powertransfer capability of the unified series-series Controller, referred to as Interline PowerFlow Controller, makes it possible to balance both the real and reactive power flowin the lines and thereby maximize the utilization of the transmission system. Note thatthe term "unified" here means that the dc terminals of all Controller converters areall connected together for real power transfer.

Combined series-shunt Controllers: [Figures 1.4(e) and 1.4(f)] This could be acombination of separate shunt and series Controllers, which are controlled in a coordi-nated manner [Figure 1.4(e)], or a Unified Power FIow Contoller with series andshunt elements [Figure 1.4(f)]. In principle, combined shunt and series Controllersinject current into the system with the shunt part of the Controller and voltage inseries in the line with the series part of the Controller. However, when the shunt andseries Controllers are unified, there can be a real power exchange between the seriesand shunt Controllers via the power link.

to

14 Chapter 1 f FACTS Concept and General System Considerations

1.6.1 Relative lmportance of Ditferent Types of Gontrollers

It is important to appreciate that the series-connected Controller impacts the

driving voltagl and hence ilie current and power flow directly. Therefore, if the purpose

of the appliJation is to control the current/power flow and damp oscillations, the

series C-ontroller for a given MVA size is several times more powerful than the

shunt Controller.As mentioned. the shunt Controller, on the other hand, is like a current

source, which draws from or injects current into the line. The shunt Controller is

therefore a good way to control voltage at and around the point of connection

through injection of ieactive current (leading or lagging), alone or a combination

of aciive and reactive current for a more effective voltage control and damping

of voltage oscillations.This is not to say that the series Controller cannot be used to keep the line

voltage within the specified range. After all, the voltage fluctuations are largely a

"on.""qo"n"" of the voltage drop in series impedances of lines, transformers, and

g"rr"rutor.. Therefore, adding or subtracting the FACTS Controller voltage in series

[main frequency, subsynchronous or harmonic voltage and combination thereof) can

be the moit cost-effe"iiu" *uy of improving the voltage profile. Nevertheless, a shunt

controller is much more effeciive in maintaining a required voltage profile at a substa-

tion bus. one important advantage of the shunt controller is that it serves the bus

node independenily of the individual lines connected to the bus.

Series Controller solution may require, but not necessarily, a separate series

Controller for several lines connected to the substation, particularly if the application

calls for contingency outage of any one line. However, this should not be a decisive

reason for choosing-a shurit-conn""t"d Controller, because the required MVA sizeof

the series Controller is small compared to the shunt Controller, and, in any case, the

shunt Controller does not provide control over the power flow in the lines'

On the other hand, ieries-connected Controllers have to be designed to ride

through contingency and dynamic overloads, and ride through or bypass short circuit

"orr"itr. They can Le proticted by metal-oxide arresters or temporarily bypassed by

solid-state devices when the fault current is too high, but they have to be rated to

handle dynamic and contingency overload.Thi above arguments suggist that a combination of the series and shunt Control-

lers [Figures 1.4(etand l.a(f]ian provide the best of both, i.e., an effective power/

current flow and line voltage control.For the combination of series and shunt Controllers, the shunt Controller can

be a single unit serving in coordination with individual line Controllers [Figure l:a(g)].

This arrangement can provide additional benefits (reactive power flow control) with

unified Controllers.FACTS Controllers may be based on thyristor devices with no gate turn-off

(only with gate turn-on), or with power devices with gate turn-off capability. Also, in

general, as will be discussed in other chapters, the principal Controllers with gate

Iurn-off devices are based on the dc to ac converters, which can exchange active and/

or reactive power with the ac system. when the exchange involves reactive power

only, they are provided with a minimal storage on the dc side. However' if the generated

ac voltage or current is required to deviate from 90 degrees with respect to the line

current or voltage, respectfuely, the converter dc storage can be augmented beyond

the minimum required for the converter operation as a source of reaitive power only'

This can be done at the converter level to cater to short-term (a few tens of main

1.6 I Basic Types of FACTS Controllers

+e-

+9-

15

E(a)

ffiLne--l(b)

(c)

ao.so(u

Line I-l

@oc()(d

(g)

dc power link

Figure 1.4 Basic types of FACTS controllers: (a) general symbol for FACTS con-troller; (b) series Controller; (c) shunt Controller; (d) unified series-series Controller; (e) coordinated series and shunt Controller; (f) unifiedseries-shunt Controller; (g) unified Controller for multiple lines; (h)series Controller with storage; (i) shunt Controller with storage; fi)unified series-shunt Controller with storase.

frequency cycles) storage needs. In addition, another storage source such as a battery,superconducting magnet, or any other source of energy can be added in parallelthrough an electronic interface to replenish the converter's dc storage. Any of theconverter-based, series, shunt, or combined shunt-series Controllers can generallyaccommodate storage, such as capacitors, batteries, and superconducting magnets,which bring an added dimension to FACTS technology [Figures 1.4(h), 1.4(i), and1.40)1.

(i)(i)

lunelI-E -lE

<- g-

Line

dc power link

Coordinatedcontrol

dc power link

L6 Chapter 1 f FACTS Concept and General System Considerations

The benefit of an added storage system (such as large dc capacitors, storage

batteries, or superconducting magnets) to the Controller is significant. A Controller

with storage is much more effective for controlling the system dynamics than the

.orr"rpottding Controller without the storage. This has to do with dynamic pumping

of reai po*"iin or out of the system as against only influencing the transfer of real

power within the system as in the case with Controllers lacking storage. Here also,

Lngineers have to rethink the role of storage, particularly the one that can deliver or

absorb large amounts of real power in short bursts.

A converter-based Controller can also be designed with so-called high pulse

order or with pulse width modulation to reduce the low order harmonic generation

to a very low level. A converter can in fact be designed to generate the correct

waveform in order to act as an active filter. It can also be controlled and operated in

a way that it balances the unbalance voltages, involving transfer of energy between

phasis. It can do all of these beneficial things simultaneously if the converter is

so designed.Given the overlap of benefits and attributes, it can be said that for a given

problem one needs to have an open mind during preliminary evaluation of series

versus shunt and combination Controllers and storage versus no storage.

1.7 BRIEF DESCRIPTION AND DEFINITIONS OF

FACTS CONTROLLERS

The purpose of this section is to briefly describe and define various shunt, series, and

"orrrbirr"d Controllers, leaving the detailed description of Controllers to their own

specific chapters.' Befori going into a very brief description of a variety of specific FACTS Control-

lers, it is worlh mentioning here that for the converter-based Controllers there are

two principal types of converters with gate turn-off devices. These are the so-called

voltage-sourced converters and the current-sourced converters' As shown in the left-

hand-side of Figure 1.5(a), the voltage-sourced converter is represented in symbolic

form by a box with a garte turn-off device paralleled by a reverse diode, and a dc

capacitlr as its voltageiout"". As shown in the right-hand side of Figure 1'5(a)' the

cuirent-sourced converter is represented by a box with a gate turn-off device with a

diode in series, and a dc reactor as its current source.

Details of a variety of voltage-sourced converters suitable for high power applica-

tions are discussed in Chapter 3, and current-sourced converters in Chapter 4. It would

suffice to say for now that for the voltage-sourced converter, unidirectional dc voltage

of a dc capacitor is presented to the ac side as ac voltage through sequential switching

of devices. Through appropriate converter topology, it is possible to vary the ac output

voltage in magnitude and also in any phase relationship to the ac system voltage' The

po*ei reversal involves reversal of current, not the voltage. When the storage capacity-ot

ttt" dc capacitor is small, and there is no other power source connected to it, the

converter cannot supply or absorb real power for much more than a cycle' The ac

output voltage is maintained at 90 degrees with reference to the ac current, leading

or Lgging, und ttt" converter is used to absorb or supply reactive power only.

For the current-sourced converter, the dc current is presented to the ac side

through the sequential switching of devices, as ac current, variable in amplitude and

also ii any phase relationship to the ac system voltage. The power reversal involves

reversal of voltage and not current. The current-sourced converter is represented

symbolically by a box with a power device, and a dc inductor as its current source.

I.7 I Brief Description and Definitions of FACTS Controllers T7

From overall cost point of view, the voltage-sourced converters seem to bepreferred, and will be the basis for presentations of most converter-based FACTS Con-trollers.

One of the facts of life is that those involved with FACTS will have to get usedto a large number of new acronyms. There are and will be more acronyms designatedby the manufacturers for their specific products, and by the authors of various papers

Line

(c)

TCRTSR

Figure 1.5

Filter

Shunt-connected Controllers: (a) Static Synchronous Compensator(STATCOM) based on voltage-sourced and current-sourced converters;(b) STATCOM with storage, i.e., Battery Energy Storage System(BESS) Superconducting Magnet Energy Storage and large dc capaci-tor; (c) Static VAR Compensator(SVC), Static VAR Generator (SVG),Static vAR System (SVS), Thyristor-Controlled Reactor (TCR), Thy-ristor-Switched Capacitor (TSC), and Thyristor-Switched Reactor(TSR); (d) Thyristor-Controlled Braking Resistor.

TTSC

LineLine Line

18 Chapter 1 I FACTS Concept and General System Considerations

on new Controllers or variations of known Controllers. The IEEE PES Task Force

of the FACTS Working Group defined Terms and Definitions for FACTS and FACTSControllers. Along with a brief description of FACTS Controllers, appropriate IEEETerms and Definitions are also presented in this section in italic for reference. Gener-

ally, this book will use the IEEE terms and definitions.

Ftexibility of Electric Power Transnissiott- The ability to accommodate changes in the

electric transmission system or operating conditions while maintaining sufficient steady-

state and transient margins.

Ftexibte AC Transmission System (FACTS), Altemating cunent transmission systerns

incorporating power electronic-based and other static controllers to enhance controllabilityand increase power transfer capability.

It is worthwhile to note the words "other static Controllers" in this definition ofFACTS implying that there can be other static Controllers which are not based on

power electronics.

FACTS Controllen A power electronic-based system and other static equipment that

prouide control of one or more AC transmission systenx parameters'

1.7.1 , Shunt Connected Controllers

Static Synchronous Compensator (STATCOM): A Static synchronous Senerator oper-

ated as a shunt-connected static var compensator whose capacitiue or inductiue output

current can be controlled independent of the ac system uoltage.

STATCOM is one of the key FACTS Controllers. It can be based on a voltage-

sourced or current-sourced converter. Figure L.5(a) shows a simple one-line diagram

of STATCOM based on a voltage-sourced converter and a current-sourced converter.

As mentioned before, from an overall cost point of view, the voltage-sourced converters

seem to be preferred, and will be the basis for presentations of most converter-based

FACTS Controllers.For the voltage-sourced converter, its ac output voltage is controlled such that

it is just right for the required reactive current flow for any ac bus voltage dc capacitor

voltage is automatically adjusted as required to serve as a voltage source for the

converter. STATCOM can be designed to also act as an active filter to absorb sys-

tem harmonics.STATCOM as defined above by IEEE is a subset of the broad based shunt

connected Controller which includes the possibility of an active power source orstorage on the dc side so that the injected current may include active power. Such a

Controller is deflned as:

Static Synchronous Generator (SSG): A static self-commutated switching power con'

uerter supplied from an appropriate electric energy source and operated to produce a set

of adjustable multiphase output uoltages, which may be coupled to an ac power system forthe purpose of exchanging independently controllable real and reactiue power.

clearly sSG is a combination of STATCOM and any energy source to supply

or absorb power. The term, SSG, generalizes connecting any source of energy including

a battery, flywheel, superconducting magnet, large dc storage capacitor, another

I.7 I Brief Description and Definitions of FACTS Controllers 19

rectifier/inverter, etc. An electronic interface known as a "chopper" is generallyneeded between the energy source and the converter. For a voltage-sourced converter,the energy source serves to appropriately compensate the capacitor charge throughthe electronic interface and maintain the required capacitor voltage.

Within the definition of SSG is also the Battery Energy Storage System (BESS),defined by IEEE as:

Battery Energy Storage System (BESS); A chemical-based energy storage system usingshunt connected, uoltage-source conuerters capable of rapidly adjusting the amount ofenergy which is supplied to or absorbed from an ac system.

Figure 1.5(b) shows a simple one-line diagram in which storage means is con-nected to a STATCOM. For transmission applications, BESS storage unit sizes wouldtend to be small (a few tens of MWHs), and if the short-time converter rating waslarge enough, it could deliver MWs with a high MW/MWH ratio for transient stability.The converter can also simultaneously absorb or deliver reactive power within theconverter's MVA capacity. when not supplying active power to the system, the con-verter is used to charge the battery at an acceptable rate.

Yet another subset of SSG, suitable for transmission applications, is the Supercon-ducting Magnetic Energy Storage (SMES), which is defined by IEEE as:

Supercondacting M agnetic Energy Storage (SM ES) : A Sup erco nducting electromagneticenergy storage deuice containing electronic conuerters that rapidly injects and/or absorbsreal and/or reactiue power or dynamically controls power flow in an ac system.

Since the dc current in the magnet does not change rapidly, the power input or outputof the magnet is changed by controlling the voltage across the magnet with a suitableelectronics interface for connection to a STATCOM.

Static Var Compensator (SVC): A shunt-connected static uar generator or absorberwhose output is adjusted. to exchange capacitiue or inductive current so as to maintain orcontrol specific parameters of the electrical power system (typically bus uoltage).

This is a general term for a thyristor-controlled or thyristor-switched reactor, and/orthyristor-switched capacitor or combination [Figure 1.5(c)]. SVC is based on thyristorswithout the gate turn-off capability. It includes separate equipment for leading andIagging vars; the thyristor-controlled or thyristor-switched reactor for absorbing reac-tive power and thyristor-switched capacitor for supplying the reactive power. SVC isconsidered by some as a lower cost alternative to STATCOM, although this may notbe the case if the comparison is made based on the required performance and nottust the MVA size.

Thyristor Controlled Reactor (ICR): A shunt-connected, thyristor-controlled inductorwhose effectiue reactance is uaried in a continuous manner by parti.al-conduction controlof the thvristor ualve.

TCR is a subset of SVC in which conduction time and hence, current in a shunt reactoris controlled by a thyristor-based ac switch with firing angle control [Figure 1.5(c)].

Thyristor Switched Reactor (TSR); A shunt-connected, thyristor-switched inductor whoseeffectiue reactance is uaried in a stepwise manner by full- or zero-conduction operation ofthe thvristor ualue.

20 Chapter 1 I FACTS Concept and General System Considerations

TSR [Figure 1.5(c)] is another a subset of SVC. TSR is made up of several shunt-connected inductors which are switched in and out by thyristor switches without anyfiring angle controls in order to achieve the required step changes in the reactivepower consumed from the system. Use of thyristor switches without firing angle controlresults in lower cost and losses. but without a continuous control.

Thyristor Switched Capacitor (TSC): A shunt-connected, thyristor-switched capacitorwhose effectiue reactance is uaried in a stepwise manner by full- or zero-conduction operationof the thyristor ualue.

TSC [Figure 1.5(c)] is also a subset of SVC in which thyristor based ac switches areused to switch in and out (without firing angle control) shunt capacitors units, in orderto achieve the required step change in the reactive power supplied to the system.Unlike shunt reactors, shunt capacitors cannot be switched continuously with variablefiring angle control.

Other broadbased definitions of series Controllers bv IEEE include:

Static Var Generator or Absorber (SVG): A static electrical device, equipment, or systemthat is capable of drawing controlled capacitive and/or inductiue current from an electricalpower system and thereby generating or absorbing reactiue power. Generally consideredto consist of shunt-connected, thyristor-controlled reactor(s) and/or thyristor-switched ca-pacitors.

The SVG, as broadly defined by IEEE, is simply a reactive power (var) sourcethat, with appropriate controls, can be converted into any specific- or multipurposereactive shunt compensator. Thus, both the SVC and the STATCOM are static uargenerators equipped with appropriate control loops to vary the var output so as tomeet speciflc compensation objectives.

Static Var System (SYS)r A combination of dffirent static and mechanically-switcheduar compensators whose outputs are coordinated.

Thyristor Controlled Braking Resistor (TCBR): A shunt-connected thyristor-switchedresistor, which is controlled to aid stabilization of a power system or to minimize poweracceleration of a generating unit during a disturbance.

TCBR involves cycle-by-cycle switching of a resistor (usually a linear resistor)with a thyristor-based ac switch with firing angle control [Figure 1.5(d)]. For lowercost, TCBR may be thyristor switched, i.e., without firing angle control. However,with flring control, half-cycle by half-cycle firing control can be utilized to selectivelydamp low-frequency oscillations.

1.7.2 Series Connected Controllers

Static Synchronous Series Compensator (SSSC): A static synchronous generator operatedwithout an extemal electric energy source as a series compensator whose output uoltage isin quadrature with, and controllable independently of, the line cutent for the purpose ofincreasing or decreasing the ouerall reactiue voltage drop across the line and therebycontrolling the transnxitted electric power. The SSSC may include transiently rated energy

storage or energy absorbing deuices to enhance the dynamic behauior of the power systemby additional ternporary real power compensation, to increase or decrease momentarily,the ouerall real (resistiue) uoltage drop across the line.

Section 1.7 I Brief Description and Definitions of FACTS Controllers 2l

.(r'l'rr Line

+ l/'-lrInterface

Storage

Figure 1.6 (a) Static Synchronous Series Compensator (SSSC); (b) SSSC with stor-age; (c) Thyristor-Controlled Series Capacitor (TCSC) and Thyristor-Switched Series Capacitor (TSSC); (d) Thyristor-Controlled Series Reac-tor (TCSR) and Thyristor-Switched Series Reactor (TSSR).

SSSC is one the most important FACTS Controllers. It is like a STATCOM,except that the output ac voltage is in series with the line. It can be based on a voltage-sourced converter [Figure 1.6(a)] or current-sourced converter. Usually the injectedvoltage in series would be quite small compared to the line voltage, and the insulationto ground would be quite high. With an appropriate insulation between the primaryand the secondary of the transformer, the converter equipment is located at the groundpotential unless the entire converter equipment is located on a platform duly insulatedfrom ground. The transformer ratio is tailored to the most economical converterdesign. Without an extra energy source, SSSC can only inject a variable voltage, whichis 90 degrees leading or lagging the current. The primary of the transformer and hencethe secondary as well as the converter has to carry full line current including the faultcurrent unless the converter is temporarily bypassed during severe line faults.

Battery-storage or superconducting magnetic storage can also be connected toa series Controller [Figure 1.6(b)] to inject a voltage vector of variable angle in serieswith the line.

Interline Power Flow Connoller (IPFC): The IPFC is a recently introduced Controllerand thus has no IEEE definition yet. A possible definition is: The combination of two ormore Static Synchronous Series Compensators which are coupled via a common dc linkto facilitate bi-directional flow of real power between the ac terminals of the SSSCs, andare controlled to prouide independent reactiue compensation for the adjustment of realpower flow in each line and rnaintain the desired distribution of reactiue power flow anxong

(a)

(b)

Line

22 Chapter 1 f FACTS Concept and General System Considerations

the lines. The IPFC structure rnay also include a STATCOM, coupled to the IFFC's common

dc link, to prouide shunt reactiue compensation and supply or absorb the ouerall real power

deficit of the combined SSSCs.

Thyristor Controlled Series Capacitor (TCSC): A capacitive reactance colnpensator

which consists of a series capacitor bank shunted by a thyristor-controlled reactor in order

to prouide a smoothly uariable series capacitiue reactance.

The TCSC [Figure 1.6(c)], is based on thyristors without the gate turn-offcapability. It is an alternative to SSSC above and like an SSSC, it is a veryimportant FACTS Controller. A variable reactor such as a Thyristor-ControlledReactor (TCR) is connected across a series capacitor. When the TCR firing angle

is 180 degrees, the reactor becomes nonconducting and the series capacitor has

its normal impedance. As the firing angle is advanced from L80 degrees to less

than 180 degrees, the capacitive impedance increases. At the other end, when the

TCR firing angle is 90 degrees, the reactor becomes fully conducting, and the totalimpedance becomes inductive, because the reactor impedance is designed to be

much lower than the series capacitor impedance. With 90 degrees firing angle, the

TCSC helps in limiting fault current. The TCSC may be a single, large unit, ormay consist of several equal or different-sized smaller capacitors in order to achieve

a superior performance.

Instead of continuous control of capacitive impedance, this approach of switching

inductors at flring angle of 90 degrees or 180 degrees but without firing angle control,

could reduce cost and losses of the Controller [Figure 1.6(c)]. It is reasonable to arrange

one of the modules to have thyristor control, while others could be thyristor switched.

Thyristor-Controlled Series Reactor (TCSR): An inductiue reactance compensator which

consists of a series reactor shunted by a thyristor controlled reactor in order to prouide a

smoothly uarinble series inductive reactance.

When the firing angle of the thyristor controlled reactor is 180 degrees, it stops

conducting, and the uncontrolled reactor acts as a fault current limiter [Figure 1.6(d)].

As the angle decreases below L80 degrees, the net inductance decreases until firingangle of 90 degrees, when the net inductance is the parallel combination of the tworeactors. As for the TCSC, the TCSR may be a single large unit or several smaller

series units.

Thyristor-Switched Series Capacitor (TSSC): Aconsists of a series capacitor bank shunted by astepwise control of series capacitiue reactance.

Thy ristor-Switched Series Reactorconsists of a series reactor shuntedprouide a stepwise control of series

cap acitiu e reactance comp ensator whichthyristor-switched reactor to prouide a

€SSR): An inductiue reactance compensator which

by a thyristor-controlled switched reactor in order toinductiue reactance.

This is a complement of TCSR, but with thyristor switches fully on or off(without firing angle control) to achieve a combination of stepped series inductance

[Figure 1.6(d)].

>:;tion 1.7 I Brief Description and Definitions of FACTS Controllers

1.7.3 Combined Shunt and Series Connected Controllers

23

Unified Power Flow Controller (UPFC): A combination of static synchronous cornpensa-tor (STATCOM) and a static series cornpensator (SSSC) which are coupled uia a commondc link, to allow bidirectional flow of real power between the series output terminals of theSSSC and the shunt output terminals of the STATCOM, and are controlled to prouideconcurrent real and reactiue series line compensation without an external electric energysource. The UPFC, by means of angularly unconstrained series uoltage injection, is ableto control, concunently or selectiuely, the transmission line uoltage, impedance, and angleor, alternatiuely, the real and reactiue power flow in the line. The UPFC may also prouideindependently controllable shunt reactiu e comp ens ation.

In UPFC [Figure 1.7(b)], which combines a STATCOM [Figure 1.5(a)] and anSSSC [Figure 1.6(a)], the active power for the series unit (SSSC) is obtained from theIine itself via the shunt unit STATCOM; the latter is also used for voltage controlwith control of its reactive power. This is a complete Controller for controlling activeand reactive power control through the line, as well as line voltage control.

Additional storage such as a superconducting magnet connected to the dc linkvia an electronic interface would provide the means of further enhancing the effective-ness of the UPFC. As mentioned before, the controlled exchange of real power withan external source, such as storage, is much more effective in control of systemdynamics than modulation of the power transfer within a system.

Thyristor-Controlled Phase Shifting Transformer (TCPST): A phase-shifting trans-

former adjusted by thyristor switches to prouide a rapidly uariable phase angle.

In general, phase shifting is obtained by adding a perpendicular voltage vector inseries with a phase. This vector is derived from the other two phases via shunt connectedtransformers [Figure 1.7(a)]. The perpendicular series voltage is made variable witha variety of power electronics topologies. A circuit concept that can handle voltagereversal can provide phase shift in either direction. This Controller is also referred toas Thyristor-Controlled Phase Angle Regulator (TCPAR).

Interphase Power Controller (IPC): A series-connected controller of actiue and reactiuepower consisting, in each phase, of inductiue and capacitiue branches subjected to separately

SSSC

STATCOM

(b)

Figure 1.7 (a) Thyristor-Controlled Phase-Shifting Transformer (TCPST) or Thyris-tor-Controlled Phase Angle Regulator (TCPR); (b) Unified Power FlowController UPFC).

3-phase line

#s3

dc link

A Chapter 1 f FACTS Concept and General System Considerations

phase-shifted voltages. The active and reactive power can be set independently by adjustingthe phase shifts and/or the branch impedances, using mechanical or electronic switches. Inthe particular case where the inductiue and capacitiue impedance form a conjugate pair,each terminal of the IPC is a passiue cunent source dependent on the uoltage at theother terminal.

This is a broadbased concept of series Controller, which can be designed to providecontrol of active and reactive power.

1.7.4 Other Controllers

Thyristor-ControlledVoltageLimiter (TCVL): Athyristor-switchedmetal-oxideuaristor(MOV) used to limit the uoltage across its terminals during transient conditions.

The thyristor switch can be connected in series with a gapless arrester, or lasshown in Figure 1.8(a)l part of the gapless arrester (10-20Vo) can be bypassed by a

Figure 1.8 Various other Controllers: (a) Thyristor-Controlled Voltage Limiter(TCVL); (b) Thyristor-Controlled Voltage Regulator (TCVR) based

on tap changing; (c) Thyristor-Controlled Voltage Regulator (TCVR)based on voltage injection.

Line

{*

Line

!-;tion 1.8 I Checklist of Possible Benefits from FACTS Technology

thyristor switch in order to dynamically lower the voltage limiting level. In general,the MOV would have to be significantly more powerful than the normal gaplessarrester, in order that TCVL can suppress dynamic overvoltages, which can otherwiselast for tens of cvcles.

Thyristor-Contolled Voltage Regalator (TCVR): A thyristor-controlled transformerwhich can provide uariable in-phase uoltage with continuous control.

For practical purposes, this may be a regular transformer with a thyristor-con-trolled tap changer [Figure 1.8(b)] or with a thyristor-controlled ac to ac voltageconverter for injection of variable ac voltage of the same phase in series with the line[Figure 1.8(c)]. Such a relatively low cost Controller can be very effective in controllingthe flow of reactive power between two ac systems.

Another family of Controllers, not defined here, but mentioned in Section 1.6are the ones that link two or more transmission lines. in order to balance the real andreactive power flows. These are discussed in Chapter 8.

1.8 CHECKLIST OF POSSIBLE BENEFITS FROMFACTS TECHNOLOGY

Details of various FACTS Controllers will be discussed throughout the book. It is

appropriate to state here that within the basic system security guidelines these Control-lers enable the transmission owners to obtain, on a case-bv-case basis, one or moreof the following benefits:

r Control of power flow as ordered. The use of control of the power flow maybe to follow a contract, meet the utilities' own needs, ensure optimum powerflow, ride through emergency conditions, or a combination thereof.

r Increase the loading capability of lines to their thermal capabilities, includingshort term and seasonal. This can be accomplished by overcoming other limita-tions, and sharing of power among lines according to their capability. It is alsoimportant to note that thermal capability of a line varies by a very large marginbased on the environmental conditions and loading history.

r Increase the system security through raising the transient stability limit,limitingshort-circuit currents and overloads, managing cascading blackouts and damp-ing electromechanical oscillations of power systems and machines.

I Provide secure tie line connections to neighboring utilities and regions therebydecreasing overall generation reserve requirements on both sides.

r Provide greater flexibility in siting new generation.r Upgrade of lines.r Reduce reactive power flows, thus allowing the lines to carry more active power.r Reduce loop flows.r Increase utilization of lowest cost generation. One of the principal reasons for

transmission interconnections is to utilize lowest cost generation. When thiscannot be done, it follows that there is not enough cost-effective transmissioncapacity. Cost-effective enhancement of capacity will therefore allow increaseduse of lowest cost generation.

There is a natural overlap among the above-cited benefits, and in reality, any one or

25

26 Chapter 1" I FACTS Concept and General System Considerations

TABLE 1.1 Control Attributes for Various Controllers

FACTS Controller Control Attributes Figure

Static Synchronous Compensator(STATCOM without storage)

Static Synchronous Compensator(STATCOM with storage, BESS,

SMES, large dc capacitor)Static VAR Compensator (SVC,

TCR, TCS, TRS)Thyristor-Controlled Braking Resis-

tor (TCBR)Static Synchronous Series Compen-

sator (SSSC without storage)Static Synchronous Series Compen-

sator (SSSC with storage)Thyristor-Controlled Series Capaci-

tor (TCSC, TSSC)Thyristor-Controlled Series Reac-

tor (TCSR, TSSR)Thyristor- Controlled Phase-Shifting

Transformer (TCPST or TCPR)Unified Power Flow Controller

(UPFC)

Thyristor-Controlled Voltage Lim-iter (TCVL)

Thyristor-Controlled Voltage Regu-lator (TCVR)

Interline Power Flow Controller(rPFC)

Voltage control, VAR compensation, damping oscillations, volt-age stability

Voltage control, VAR compensation, damping oscillations, tran-sient and dynamic stability, voltage stability, AGC

Voltage control, VAR compensation, damping oscillations, tran-sient and dynamic stability, voltage stability

Damping oscillations, transient and dynamic stability

Current control, damping oscillations, transient and dynamic sta-

bility, voltage stability, fault current limitingCurrent control, damping oscillations, transient and dynamic sta-

bility, voltage stabilityCurrent control, damping oscillations, transient and dynamic sta-

bility, voltage stability, fault current limitingCurrent control, damping oscillations, transient and dynamic sta-

bility, voltage stability, fault current limitingActive power control, damping oscillations, transient and dy-

namic stability, voltage stabilityActive and reactive power control, voltage control, VAR compen-

sation, damping oscillations, transient and dynamic stability,voltage stability, fault current limiting

Transient and dynamic voltage limit

Reactive power control, voltage control, damping oscillations,transient and dynamic stability, voltage stability

Reactive power control, voltage control, damping oscillations,transient and dynamic stability, voltage stability

1.s(a)

1.s(b)

1.5(c)

1.s(d;

1.5(a)

1.6(b)

1.6(c)

1.6(d)

1.7 (a)

1.7(b)

1.8(a)

1.8(b)1.8(c)1.4(d)

1.9

two of these benefits would be a principal justification for the choice of a FACTSController. It is, however, important to check the list of these benefits on a value-added basis.

Because the voltage, current, impedance, real power, and reactive power areinterrelated, each Controller has multiple attributes of what they can do in terms ofcontrolling the voltage, power flow, stability and so on. These controllers can havemultiple open loop and closed loop controls to accomplish multiple beneflts. TableL.L gives a checklist of control attributes for various Controllers. The list is not exhaus-tive, in particular it does not include the Controllers that link multiple lines, discussedin Chapter 8. Of course the degree of controllability, in particular the control ofstability and power flow will vary from Controller to Controller. For understandingthe value of these Controllers, one needs to read detail in various chapters of this book.

lN PERSPECTIVE: HVDC OR FACTS

It is important to recognize that generally HVDC and FACTS are complementarytechnologies. HVDC is not a grid network in the way that an ac system is, nor is itexpected to be. The role of HVDC, for economic reasons, is to interconnect ac systems

where a reliable ac interconnection would be too expensive.There are now over 50 HVDC projects in the world. These can be divided into

four categories:

Section 1.9 I In Perspective: HVDC or FACTS 27

Submarine cables. Cables have a large capacitance, and hence ac cables requirea large charging current (reactive power) an order of magnitude larger thanthat of overhead lines. As a result, for over a 30 km or so stretch of acsubmarine cable, the charging current supplied from the shore will fully loadthe cable and leave no room for transmitting real power. The charging currentflowing in the cables can only be reduced by connecting shunt inductors tothe cable at intervals of 15-20 km, thus requiring appropriate land location.With HVDC cable on the other hand, distance is not a technical barrier. Also,the cost of dc cable transmission is much lower than that of ac which worksto HVDC's advantage to cover new markets for long distance submarinetransmission. In this area, FACTS technology (e.9., the UPFC) can providean improvement by controlling the magnitude of one of the end (e.g., thereceiving-end) voltages so as to keep it identical to that of the other one. Inthis way, the effective length of the cable from the standpoint of the chargingcurrent can be halved. This approach may provide an economical solutionfor moderate submarine distances, up to about 100 km, but for long distancetransmission HVDC will remain unchallenged.

Long distance overhead transmission. If the overhead transmission is longenough, say 1.000 km, the saving in capital costs and losses with a dc transmis-sion line may be enough to pay for two converters (note that HVDC representstotal power electronics rating of 2007o of. the rated transmission capacity).This distance is known as the break-even distance. This break-euen distanceis very subject to many factors including the cost of the line, right-of-way,any need to tap the line along the way, and often most important, the politicsof obtaining permission to build the line. Nevertheless, it is important torecognize that while FACTS can play an important role in an effective useof ac transmission, it probably does not have too much influence on the break-even distance. Thus, the principal role of FACTS is in the vast ac transmissionmarket where HVDC is generally not economically viable.

3. Underground transmission. Because of the high cost of underground cables,the break even distance for HVDC is more like 100 km as against 1000 kmfor overhead lines. Again, FACTS technology probably does not have muchinfluence in this break-even distance. In any case, to date there have been nolong distance underground projects, either ac or dc, because, in an openlandscape, overhead transmission costs so much less than underground trans-mission (about25%o of the costs of underground transmission). Cable transmis-sion, on the other hand, has a significant potential of cost reduction, both inthe cost of cables and construction cost.

4. Connecting ac systems of different or incompatible frequencies. For historicalreasons, the oceans in effect separate the globe's electric systems into 50 Hzand 60 Hz groups. The 60 Hz normal frequency pervades all the countries ofthe Americas, excepting Argentina and Paraguay. Those two countries andall the rest of the world have a 50 Hz frequency except Japan, which is partly50 Hz and partly 6O }Iz.In general, the oceans are too huge and deep tojustify interconnections of 50 and 60 Hz systems. Thus there is a limitedmarket for HVDC for connectins 50 and 60 Hz svstems.

The related, but larger, HVDC market consists of tying together ac systems thathave incompatible frequency control such that the phase angle between the two systems

l-.

2.

28 Chapter 1 f FACTS Concept and General System Considerations

frequently straddles the full circle or very large part of a circle. Even once or twiceper day excursion of phase angle in excess of 60 degrees would be often enough torule out any contrived mechanical phase shifter. HVDC can solve this problem. Todate there are many HVDC projects, most of them back-to-back ties, which serve thisneed, and some include some length of dc line as well. Experts agree that some tiesof this kind will drop out of use once the neighbors agree upon and implement a

common frequency control strategy. This is in fact what has happened in Europe. Notso very long ago, members of the former Comecon (East Europe and the Europeanpart of the former USSR) were interconnected as one ac system, but could not beconnected to the West European system, known as UCPTE, because they employeddifferent kinds of frequency control and available reserve margins. Then the desireto exchange power with East Europe prompted the installation of three back-to-backties: the Diirnrohr 550 MW tie connecting Austria to Poland, the Etzenricht 600 MWtie connecting Germany to the Czech Republic, and the Vienna East-West 600 MWtie connecting Austria to Hungary. However, with the subsequent unification of Ger-many and other political developments, East Germany and the East European coun-tries of Poland, the Slovak and Czech Republics, and Hungary formed themselves

into the Centrel Group and installed and field-calibrated their controls at their powerplants and control centers. Then in September and October of 1995, their systems

were connected to the West European system by ac. Other members of the formerComecon are either operating in isolation or connected to the Integrated Power System

with Russia. One side effect is that the three back-to-back HVDC ties, the Diirnrohrand Sud-Ost in Austria and the Etzenricht in Germany, were bypassed and no longerused. This will also happen in India where electricity regions have been connectedwith back-to-back ties.

There are also many locations in the world where frequency control strategies

are the same, but, because of the remoteness of centers of electrical gravity from thedesired points of connection, phase angle drifts and varies over a wide angle withdaily variations in load and even go full circle. The Eastern and Western United States

systems are an example of this, and therefore they are connected with several back-to-back HVDC ties. Conceptually, FACTS technology can also solve this problem ofwide variations of phase angle. It requires, for example, a phase-angle Controller forone side to chase or lead the other as required through full circle. This is in facttechnically feasible with known concepts of phase angle Controller. However, theeconomics are perhaps in favor of HVDC. After all, HVDC is independent of phase

angle and therefore, in a way, equivalent to a 360 degree phase angle Controller, anda true 360 degree phase angle Controller may be more expensive.

Large market potential for FACTS is within the ac system on a value-addedbasis. where:

the existing steady-state phase angle between bus nodes is reasonable,

the cost of a FACTS solution is lower than the HVDC cost, and

the required FACTS Controller capacity is less than, say,l\O%o of the transmis-sion throughput rating.

Figure 1.9 conveys the basic attributes of HVDC and FACTS, and also general cost

comparison between HVDC and FACTS where FACTS solutions are viable and couldhave scope of applications.

t

I

I

3.;ferences 29

Installed Costs (millions of dollars)

Throughput MW

2OO MW5OO MW

1000 MW2000 MW

HVDC:

r Independent frequency and controlI Lower line costso Power control, voltage control,

stability control

EAAIqo Power control, voltage control,

stability control

HVDC 2 Terminals

$ 40-50 M75- 1 00

124-170200-300

FACTS

$ 5-10 M1 0-2020-3030-50

Figure 1-.9 HVDC and FACTS: Complementary solutions.

REFERENCES

Adapa, R., "Summary of EPRI's FACTS System Studies," CIGRE SC 14 International Collo-quium on HVDC & FACTS, Montreal, September 1995.

Ainsworth, J. D., Davies, M., Fitz, P. J., Owen, K. E., and Trainer, D. R., "A Static VARCompensator Based on Single-Phase Chain Circuit Converters," IEE Proc. Gen. Trans. andDlsL, vol. 145, no. 4, July 1998.

Arabi, S., Kundur, P., and Adapa, R., "Innovative Techniques in Modeling UPFC for PowerSystem Analysis," Paper PE-231-PWRS-0-10-1998 IEEE PES Winter Meeting, New York,January-Feb ruary 1999.

Baker, M. H., "An Assessment of FACTS Controllers for Transmission System Enhancement,"CIGRE SC 14 International Colloquium on HVDC & FACTS, Montreal, September 1995.

Baker, M. H., Povh, D., and Larsen, E. V., "FACTS Equipment," Special Report CIGRESymposium on Power Electronics in Electric Power Systems, Tokyo, May 1995.

Baker, M. H., Thanawala, H, L., Young, D. J., and Erinmez L. A. "Static VAR CompensatorsEnhance a Meshed Transmission System," CIGRE Special Report: Technology and Benefitsof Flexible AC Transmission Systems, loint Session of SC14/37/38, Paris, 1992.

Breuer, G., "Flexible AC Transmission Scoping Studies," EPRI Proceedlngs, FACTS Confer-ence 1., Cincinnati, OH, November 1990.

Brochun J., Pelletier, P., Beauregard, F., and Morin, G., "The Interphase Power Controller, Anew Concept for Managing Power Flow Within AC Networks," IEEE Transactions on PowerDeliuery, vol. 9, no. 2, pp. 833-841, April 1994.

Canizares, C. A., "Analysis of SVC and TCSC in Voltage Collapse," IEEE PES 1998 SummerMeeting, San Diego, CA, July L998.

Cannon, D. Jr., Stevenson, C., Hanson, D., Lyons, P. F., and McCafferty, M., "ASCR ConductorPerformance Under High Thermal Loading" EPRI Conference on the Future of Power Deliu-ery, Washington, DC, April 1996.

Casazza, J. A., and Lekang, D. J., "New FACTS Technology: Its Potential Impact on Transmis-sion System Utilization," EPRI Conference on Flexible AC Transmission System, Cincinnati,OH. November 1990.

30 Chapter 1 f FACTS Concept and General System Considerations

Chamia, M., "Power Flow Control in Highly Integrated Transmission Network," EPRI Confer-ence on Flexible AC Transmission System, Cincinnati, OH, November 1990.

Davriu, A., Douard, G., Mallet, P., and Therond, P. G., "Taking Account of FACTS InvestmentSelection Studies," CIGRE Symposium on Power Electronics in Electric Power Systems,

Tokyo, May 1995.

Davriu, A., Mallet, P., and Pramayon, P., "Evaluation of FACTS Functionalities Within thePlanning of the Very High Voltage Transmission Network: The EDF Approach," Proceedingsof the IEEE/Royal Institute of Technology Stockholm Power Tech: Power Electronicg Stock-holm, June 1.995.

DeMarco, C. L., "Security Measures To Evaluate the Impact of FACTS Devices in PreventingVoltage Collapse," Proceedings of EPRI Conference on Flexible AC Transmission Systems(FACTS), Boston, MA, May 1992.

Deuse, J., Stubbe, M., Meyer, B., and Panciatici, P., "Modeling of FACTS for Power SystemAnalysis," CIGRE Symposium on Power Electronics in Electric Power Systems, Tokyo,May 1995.

Douglass, D. A., Edris, A. A., and Pritchard, G. A., "Field Application of A Dynamic ThermalCircuit Rating Method," 1EE E PES 1995 Winter Meeting New York, January-February 1.995.

Edris A., Adapa, R., Baker, M. H., Bohmann, L., Clark, K., Habashi, K., Gyugui, L.,Lemay,J., Mehraban, A. S., Meyers, A. K., Reeve, J., Sener, F., Torgerson, D. R., and Wood, R. R.,"Proposed Terms and Definitions for Flexible AC Transmission System (FACTS)," IEEETrans on Power Deliuery, vol. 12, no. 4, October 1997, pp. 1848-1853.

Edris, E., "Enhancement of First-Swing Stability Using a High Speed Phase Shifter," IEEETrans. Power Systems, vol. 6, no. 3, pp. 1113-1118, 1991.

Erche, M., Lerch, E., Povh, D., and Mihalic, R., "Improvement of Power System PerformanceUsing Power Electronic Equipment," CIGRE Special Report: Technology and Benefits ofFlexible AC Transmission Systems, foint Session of SC14/37/38, Paris, 1992.

Ewart, D. N., Koessler, R. J., Mountford, J. D., and Maratukulam, D., "FACTS Options Permitthe Utilization of the FullThermal Capacityof ACTransmission," 1EE Conference PublicationSeries 5, International Conference on AC and DC Power Transmission, London, IEE Publica-tion No. 345, pp. 1-7, September 199'1,.

Eunson, E. M., and Meslier, F., "Planning of the Power System Taking Into Account theApplication of Power Electronics," Special Report for Session 2, CIGRE 1995 Symposiumon Power Electronics in Electric Power Systemg Tokyo, May 1995.

Eunson, E. M., Meslier, Daniel, D., Le Du, A., Poumarede, C., Therond, P. G., Langlet, B.,Taisne, J. P., and Collet-Billon, V., "Power Electronics: An Effective Tool for NetworkDevelopment? An Electricite de France Answer Based on the Development of a PrototypeUnified Power Flow Controller," CIGRE Symposium on Power Electronics in Electric PowerSystems, Tokyo, May 1995.

Falk, Christensen, J., "More Effective Networks," CIGRE Special Report P1-00, Paris, Ses-sion, 1996.

Feak, S. D., "Superconducting Magnetic Energy Storage (SMES): Utility Application Studies,"IEEE PES 1996 Summer Meeting, Denver, Paper 96 SM 472-1-PWRS, July-August 1996.

Ferguson, J., Woolery, B., and Lyons, P. F., "Innovative Upgrades of Transmission Lines,"EPRI Conference on the Future of Power Deliuery, Washington, DC, April 1996.

Galiana, F. D., Almeida, K., Toussaint, M., Griffen, J., Ooi, B. T., and McGillis, D. T., "Assess-ment and Control of the Impact of FACTS Devices on Power System Performance," IEEEPES 1996 Winter Meeting, Baltimore, Paper 96 WM 256-8-PWRS, January 1996.

Gama, C. A., Ellery, E. H., Azvedo, D. C. B., and Ponte, J. R. R., "Static VAR Compensators(SVC) Versus Synchronous Condesners (SC) for Inverter Stations Compensation-Technicaland Economical Aspects in Electronorte Studies," CIGRE Group 14 Paper 14-103, 1992.

Gjengedal, T., Gjerde, J. O., and Flolo, R., "Prospective Use of HVDC and FACTS-

31

Components for Enhancement of Power System Stability in the Norwegian Main Grid,,'EPRI Conference on the Future of Power Deliuery, Washington, DC, April 1996.

Gyugyi, L., "Solid State Control of AC Power Transmission," EPRI Conference on FlexibleAC Transmission System, Proceedings, Cincinnati, OH, November 1990.

Hammad, A. E., "Comparing the Voltage Control Capabilities of _Present and Future VARCompensating Techniques in Transmission Systems," IEEE Transactions on Power Deliuery,vol. 1.1, no. L, January 1.995.

Hammad, A. E., "FACTS Control Concepts: Case Study for Voltage Stability," EPRI Confer-ence on the Future of Power Deliuery, Washington, DC, April 1996.

Hammad, A. E., "FACTS Specification: Criteria and Associated Studies," EPRI Conferenceon the Future of Power Deliuery, Washington, DC, April L996.

Henderson, M., and Lemay, J., "Design and Implementation of the Interphase Power ControllerBetween NYPA and vELCo Systems," IEEE PES 98 summer Meeting, San Diego, cA.July 1998.

Henderson, M. I., "Operating Issues for FACTS Devices: An Operations Planning Perspective,"EPRI conference on Flexible AC Transmission system, Baltimore, MD, october 1994.

Hingorani, N. G., "Power Electronics in AC Transmission Systems," cIGRE special ReportPl-02, Pais Session, 1996.

Hingorani, N. G., "Future opportunities for Electric Power Systems," IEEE pES SummerPower Meeting Luncheon Speech, San Francisco, CA, July 1987.

Hingorani, N. G., "Power Electronics in Electric Utilities: Role of Power Electronics in FuturePower Systems," Proceedings of the IEEE Special Issue, vol.76, no. 4, April 1988.

Hingorani, N. G., "High Power Electronics and Flexible AC Transmission System,,, IEEEPower Engineering Reuiew, vol. 8, no. 7, July L988. Reprint of Joint American powerConference/IEEE Luncheon Speech, Chicago, IL, April 1988.

Hingorani, N. G., "Flexible AC Transmission Systems (FACTS)-overview," paper presentedat the Panel Session of FACTS, IEEE PES 1990 winter Meeting, Atlanta, February 1990.

Hingorani, N. G., "FACTS: Flexible AC Transmission Systems," EPRI conference on FlexibleAC Transmission Systern, Cincinnati, OH, November 1990.

Hingorani, N. G., "FACTS-Flexible AC Transmission System," Proceedings of the FifthInternational Conference on AC and DC Power Transmission, London, IEE Publication No.345, pp. 1.-7, September 199L.

Hingorani, N. G., "Flexible AC Transmission," IEEE Spectrum, vol.30, no. 4, April 1993.

Hingorani, N. G., and Stahlkopf, K. E., "High Power Electronics," scienffic American, vol.269, no. 5, pp. 77 -85, November 1993.

Hingorani, N. G., "Power Electronics," IEEE Power Engineering Reuiew, vol. l-5, no. 10,October 1995.

IEEE Power Electronics Modeling Task Force, "Guidelines for Modeling Power Electronicsin Electric Power Engineering Applicationso" IEEE 1996 pES summer Meeting, Denver,Paper 96 SM 439-0-PWRD, July-August 1996.

Kapoor, S. C., Tripathy, A.K., Kumar, M., Senthil, J., Adhikari, T., and Chaukiyal, G. p., ,,AProposed Rapid Network Impedance Control Scheme for an Existing Power Corridor inIndia," Proceedings of CIGRE Group 14, Paper 14-106, August-September 1994.

Klein, M., Le, L. X., Rogers, G. J., Farrokhpay, S., and Balu, N. J., ,,H-Inflnity DampingController Design in Large Power Systems," IEEE Transactions on Power Systems, vol. 10,no. 1, pp. 158-166, February 1995.

Koessler, R., "Investigation of FACTS Options to Utilize the Full Thermal Capacity of ACTransmission," EPRI Conference on Flexible AC Transmission System, Cincinnati, OH, No-vember 1.990.

Kurita, A., okubo, H., Miller, N. w., and Sanchez-Gasca, J. J., "Application of Fast controllable

32 Chapter 1 f FACTS Concept and General System Considerations

Electronic Devices for Performance Enhancement in Tightly Interconnected Systems,"

CIGRE 1995 Syrnposium on Power Electronics in Electric Power System.r, Tokyo, May 1995.

Lachs, W. R., Sutanto, D., and Logothetis, D. N., "Power System Control in the Next Century,"

IEEE Transactions on Power System,s, vol. L1, no. L, pp. 11-18, February 1996.

Lacoste, J., Cholley, P., Trotignon, M', Daniel, D., and Nativel, G'' "FACTS Equipment and

Power System Dynamics," CIGRE 1995 Symposium on Power Electronics in Electric Power

Systems, Tokyo, May L995.

Larsen, E., Bowler, C., Damsky, B., and Nilsson, S., "Beneflts of Thyristor Controlled Series

Compensation," CIGRE Special Report: Technology and Benefits of Flexible AC Transmission

Systems, Joint Session of SC14/37/38, Patis, 1992.

Larsen,E'., and weaver, T.,.,FACTS Overview," IEEE/CIGRE FACTSWorking Group, IEEETechnical Publication 95 TP108,84 pages, 1995.

Larsen, E., and Sener, F., "Current Activity in Flexible AC Transmission System (FACTS),"I E E E Pub lic atio n N o. 92 T H0 46 5 - 5' PW R, Aptll 1992'

Le Du, A., Tontini, G., and winfield, M., "which FACTS Equipment for which Need? Identifl-cation of the Technology Developments to Meet the Needs of Electricite de France (EDF),Ente Nazionale per I'Energia Eletrica (ENEL) and National Grid Company (NGC)," CIGRESpecial Report: Technology and Benefits of Flexible AC Transmission Systerns, loint Session

of S Cl 4/ 37 / 3 8, P ais, 1992.

Lei, X., Lerch, E., Povh, D., Wang, X., and Haubrich, H. J', "Global Settings of FACTS

controllers in Power Systems," CIGRE Session Group 14, Paris, Paper 14-305, t996.

Lemay, J., "A Planner's View of FACTS: Meeting the Needs of Modern Networks Power,"

Technology International, United Kingdom, pp. 109-111, 1996.

Lerch,3,., and Povh, D., "Performance of AC Systems Using FACTS Equipment," Proceedings

of EPRI Conference on Flexible AC Transmission Systems (FACTS), Boston, MA, May 1992.

Lu, C. F., Liu, c. c., and wu, c. J., ,,Dynamic Modeling of Battery Energy Storage System

and Application to Power System Stability," IEE Proceedings, Generation, Transmission and

Di.stribution, vol. 142, no. 4, pp. 429-435, July 1995'

Maguire, T. L., and Gole, A. M., "Digital Simulation of Flexible Topology Power Electronic

Apparatus in Power Systems," IEEE SM 414-3 PWRD, t99l'Maliszewski, R. M., Eunson, E. M., Meslier, F., Balazs, P., Schwarz, J.' Takahashi, K', and

Wallace, P., "Interaction of System Planning in the Development of the Transmission Net-

works of the 21st Century,- CIGRE 1995 Symposium on Power Electronics in Electric Power

Systems, Tokyo, May 1995.

Maliszewski, R. M., and Meslier, F., "More Effective Network: An Answer to Question L0 ofthe Special Report," CIGRE Special Report P/-04 Session t996.

Maliszewski. R. M., Pasternack, B. M., Scherer, Jr', H. N', Chamia, M., Frank, H., and Paulsson,

L., "Power Flow in a Highly Interconnected Transmission Network," CIGRE Paper 37-303,

Paris. 1990 Session. 1990.

Manzoni, G., Salvaderi, Eunson, E. M., Schwarz,J.,andCasazza,I' A., "Power System Planning

with Changing Institutional Arrangements," CIGRE Panel Session Paper No. P2-01' 1996.

Miller, N. W., Mukerji, R., and Clayton, R. E., "The Role of Power Electronics in Open Access

Markets," EPRI Conference on the Future of Power Delivery, Washington, DC, April 1996.

Mitani, Y., Uranaka, T., and Tsuji, K., "Power System Stabilization by Superconducting Magnetic

Energy Storage with Solid State Phase Shifter," IEEE Transactions on Power Systems, vol.10, no. 3, August 1995.

Mittelstadt, W. A., "Considerations in Planning Use of FACTS Devices on a Utility System,"

EPRI Conference on Flexible AC Transmission System, Proceedings, Cincinnati, OH, Novem-

ber 1990.

Nilsson, S. L., "security Aspects of Flexible AC Transmission System Controller Applications,"

33

International Journal of Electrical Power and Energy systems (United Kingdom), vol. 17,no.3, pp. 173-179, June 1995.

Norris, W. T., and James, D. A., "Series Compensation Using Power Electronic Switches:The SERCOM," Proceedings of the IEE Sixth International Conference on AC and DCTransmission, pp. 405-410, April-May 1996.

Oh, T. K., Choi, K. H., Byon, S. B., Kim, Y. H., Hwang, J. Y., and Lee, K. J., "Power TransferCapability Increase and Transient Stability Enhancement by FACTS Devices Application,"EPRI Conference on the Future of Power Deliuery, Washington, DC, April 1996.

Okamoto, H., Kurita, A., and Sekine, Y., "A Method for Identification of Effective Locationsof Variable Impedance Apparatus on Enhancement of Steady-State Stability in Large ScalePower Systems," IEEE Transactions on Power Systems, vol. 10, no. 3, August 1995.

Ooi, B. T., Kazerani, M., Marceau, R., Wolanski,Z., Galiana, F. D., McGillis, D., and Joos,G., "Mid-Point Siting of FACTS Devices in Transmission Lines," Paper No. PE-292-PWRD-0-01-1997, IEEE PES, 1997.

Padiyar, K. R., Geetha, M.K., and Rao, K. U., "A Novel Power Flow Controller for ControlledSeries Compensation," Proceedings, of the IEE Sixth International Conference on AC andD C Transmission, pp. 3290-3334, April-May 1996.

Padiyar, K. R., and Kulkarni, A. M., "Application of Static Condenser for Enhancing PowerTransfer in Long AC Lines," CIGRE 1995 Symposium on Power Electronics in Electric PowerSystems, Tokyo, May 1995.

Padiyar, K. R., and Rao, K. U., "Discrete Control of TCSC for Stability Improvement inPower Systems," Proceedings, IEEE Fourth Conference on Control Applications, Albany,NY, pp.246-251, September 1995.

Paserba, J. J., Condordia, C., Lerch, E., Lysheim, D. P., Ostojic, D., Thorvaldsson, B. H.,Dagle, J. E., Trudnowski, D. J., Hauer, J. F., and Janssens, N., "Opportunities for DampingOscillations by Applying Power Electronics in Electric Power Systems," CIGRE 1995 Sympo-sium on Power Electronics in Electric Power Systems, Tokyo, May 1995.

Pastos, D. A., Vovos, N. A., and Giannakopoulos, G. B., "Comparison of Compensators Capabil-ity to Modulate the Real Power Flow in Integrated AC/DC Systems," IEEE PES 97 SummerMeeting, Berlin, Germany, July L997.

Pilotto, L. A. S., Ping, W. W., Carvalho, A.R., Prado, S., Wey, A., Long, W. F., and Edris,A. A., "First Results on the Analysis of Control Interactions on FACTS Assisted PowerSystems," EPRI Conference on Flexible AC Transmission System, Baltimore, MD, Octo-ber 1994.

Pilotto, L. A. S., Ping, W. W., Carvalho, A. R., Wey, A., Long, W. F., Alvarado, F. L., DeMarco,C. L., and Edris, A. A., "Determination of Needed FACTS Controllers That Increase AssetUtilization of Power Systems," IEEE PES 1996 Winter Meeting, Baltimore, Paper 96 WM090-1-PWRD, J annary 1996.

Povh, D., "Advantages of Power Electronics Equipment in AC Systems," CIGRE SC14 Interna-tio nal C o llo quium o n HV D C an d FA C T S S y stems, W ellin1ton, New Zealand, Septemb er 1993.

Povh, D., and Mihalic, R., "Enhancement of Transient Stability on AC Transmission by Meansof Controlled Series and Parallel Compensation," IEE Conference Publication Series 5, Inter-national Conference on AC and DC Power Transmlsslo4 London, IEE Publication No. 345,pp. 8-l2,September 1991.

Povh, D., Mihalic, R., and Papic, I., "FACTS Equipment for Load Flow Control In High VoltageSystems," CIGRE 1995 Symposium on Power Electronics in Electric Power Systems, Tokyo,May 1995.

Pramayon, P., Nonnon, P., Mallet, P., Trotignon, M., and Lauzanne, B,, "Methodology forTechnical and Economical Evaluation of FACTS Impact and Efflciency on EHVTransmissionSystem," EPRI Conference on the Future of Power Deliuery, Washington DC, April L996.

Rajaraman, R., "Oscillations in Power Systems with Thyristor Switching Devices," IEEE PES196 Winter Meeting, Baltimore, Paper 96 WM 255-0-PWRS, January 1996.

34 Chapter 1 f FACTS Concept and General System Considerations

Rajaraman, R., and Dobson, I., "Damping Estimates of Subsynchronous and Power Swing

Oscillations in Power Systems with Thyristor Switching Devices," IEEE PES Winter Meeting,

Baltimore, January 1996.

Rajaraman, R., Maniaci, A., and Camfield, R., "Determination of Location and Amount of

Series Compensation to Increase Over Transfer Capability," IEEE PES 97 Summer Meeting,

Berlin, Germany, July 1997.

Ray, C., "Meeting Security and Quality Requirements In an Open Market," EPRI Conference

on the Future of Power Deliuery, Washington, DC, April 1996'

Rehtanz, C., "systemic Use of Multifunctional SMES in Electric Power Systems," Paper PE-

224-PWRS-0-10-1998, IEEE PES Winter Meeting, New York, January-February L999.

Sanchez, J. J., "Coordinated Control of Two FACTS Devices for Damping Inter-Area Oscilla-

tions," IEEE PES 97 Summer Meeting, Berlin' Germany, July 1997'

Sekine, Y., Hayashi, T., Abe, K., Inoue, Y., and Horiuchi, S., "Application of Power Electronics

Technologiei to Future Interconnected Power System in Japan," CIGRE 1995 Symposium

on Power Electronics in Electric Power System,s, Tokyo, May L995'

Sekine, Y., Takahashi, K., and Hayashi, T., "Application of Power Electronics Technologies

to the 21st Century's Bulk Power Transmission in Japan," International loumal of Electrical

Power and Energy systems (United Kingdom), vol. 17, no. 3, pp. 181-193, June 1995'

Simo, J. 8., and Kamwa, I., "Exploratory Assessment of the Dynamic Behavior of Multi-

Machine System Stabilized by a SMES lJnit," IEEE Transactions on Power Systems, vol. 10,

no. 3, August 1995.

Singh,8., Al-Haddad, K., and Chandra, A., "A New Control Approach to Three Phase Activepiwer for Harmonics and Reactive Power Compensation," IEEE PES 97 Summer Meeting,

Berlin, Germany, JulY 1997.

Smith, P., Thanawala, H. L., and Corcoran, J. W. C., "Potential Application of Power Electronic

Equipment in the Irish Power Transmission System," CIGRE 19p.5 Symposium on Power

Electronics in Electric Power Systems, Tokyo, May 1995'

Strbac, G., and Jenkins, N., "FACTS Devices in Uplift Control," Proceedings of the IEE Sixth

International Conference on AC and DC Transmission, pp.214-219, April-May 1'996.

Sugimoto, S., Kida, J., Arita, H., Fukui, c., and Yamagiwa, T., "Principle and characteristics

of a Fault Current Limiter With Series Compensatiot," IEEE Transactions on Power Delivery,

vol. 11., no. 2, April 1996.

Sultan, M., Reeve, J. R., and Adapa, R., "Combined Transient and Dynamic Analysis of HVDCand FACTS Systems," Paper No. PE-83-PWRD-0-1-1998, IEEE PES, 1998

Sybille, G., Haj-Maharsi, Y., Morin, G., Beauregard, F., Brochu, J., Lemay, J', and Pelletier,p., ,,simulator Demonstration of the Interphase Power Controller Technology" IEEE PES

1996 Winter Meeting, Baltimore, January L996.

Tang, Y., and Meliopoulos, A. P. S., "Power System Small Signal Stability Analysis with

f'aCfS Elements," IEEE PES 1996 Summer Meeting, Denver, Paper 96 SM 467-1-PWRD'

July-August 1996.

Taranto, G. N., Chow, J. H., and Othman, H. A., "Robust Redesign of Power System Damping

Controllers," IEEE Transactions on Control Systems Technology, vol.3, no. 3'pp.290-298,

September L995.

Taranto, G. N., Pinto, L. M. V. G., and Pereira, M. v. F., "Representation of FACTS Devices

in Power System Economic Dispatch," IEEE Trans Power system,r, vol.7, no.2, pp. 572-576,

May 1992.

Tenorio, A. R. M., Ekanayake, J. B., and Jenkins, N. "Modeling of FACTS Devices," Proceed-

ings of the IEE Sixth international Conference on AC and DC Transmission, pp.340-345,

April-May 1996.

Tripathy, S. C., and Juengst, K. P., "sampled Data Automatic generation Control with Supercon-

35

ducting Magnetic Energy Storage in Power System," IEEE PES 1996 Winter Meeting, Balti-more, Paper 96 WM 046-3-EC, January L996.

Vieira, X., Szechtman, M., Salgado,8., Praca, J. C. G., Ping, W. W., and Bianco, A., ,,prospective

Applications of FACTS in the Brazilian Interconnected Power Systems ," CIGRE 1995 Sympo-sium on Power Electronics in Electric Power Systems, Tokyo, May 1995.

Wang, Y., Mohler, R. R., Spee, R., and Mittetstadt, S. W., "Variable Structure FACTS Control-lers for Power System Transient Stability," IEEE Trans Power System,s, vol. 7, no. 1, pp.307-313, February 1992.

Wang, H. F., and Swift, F. J., "A Unified Model for the Analysis of FACTS Devices in DampingPower System Oscillations. Part 1: Single-Machine Infinite-Bus Power Systems,,, IEEE pES1996 Summer Meeting, Denver, Paper 96 SM 464-8-PWRD, July-August 1996.

Yokoyama, A., okamoto, H., and Sekine, Y., "Simulation Study on Steady State and rransientStability Enhancement of Multi-Machine Power System by Dynamic Control of VariableSeries Capacitor," CIGRE 1995 Symposium on Power Electronics in Electric Power Systems,Tokyo, May 1995.