typical data sheet

CI ACCESS FITTING

PROJECT

DATA SHEET FOR CORROSION INHIBITOR INJECTION ACCESS FITTINGMANUFACTURER:SERVICE:PRODUCED WATERSIZE: REFER BELOW1TAG NO. 23DESCRIPTIONSPECIFICATION REQUIREMENTVENDOR'S CONFIRMATION4GENERAL DATA5ACCESS FITTING TYPE:RETRACTABLE TYPE6ASME CLASS / RATING:150#7INLET NOZZLE SIZE & CONFIGURATION:1", FLANGED (RF), SMOOTH FINISH (125-250 in)8HEADER CONNECTION SIZE & CONFIGURATION:2", FLAREWELD, 6000#9PIPING CLASS:A1E10CORROSION ALLOWANCE:3 MM11BODY TYPE:TEE TYPE WITH SOLID PLUG ASSEMBLY AND HEAVY CS12PROTECTIVE COVER 13INJECTION TUBE:ATOMIZING INJECTION QUILL TYPE14INSTALLATION / MOUNTING:AT 12 O CLOCK POSITION ON HEADER ABOVE GROUND1516HEADER PIPE DETAILS:As in MTO1718MATERIALS19BODY / FLANGE:A10520INTERNALS / SOLID PLUG:SS31621PROTECTIVE COVER :A10522INJECTION TUBE / QUILL:SS31623PRIMARY PACKING AND BACK UP RING:PTFE24O-RING:VITON (ANTI EXPLOSIVE DECOMPRESSION TYPE)25PIPE PLUG:SS3162627CODES AND STANDARDS / TESTING / CERTIFICATION 28DESIGN CODE:PRESSURE RETAINING PARTS AS PER ASME B31.329FACE TO FACE DIMENSIONS:AS PER MANUFACTURER'S STANDARD30FLANGE END DIMENSIONSAS PER ASME B16.531HYDRO STATIC TEST:1.5 TIMES OF DESIGN PRESSURE (MINIMUM)32NDT. (MPI / DP / RADIOGRAPHY / UT ETC.):AS PER ASME B 31.333MATERIAL CERTIFICATION :EN 10204 TYPE 3.134PAINTING:AS PER MANUFACTURER'S STANDARD3536MARKING:MSS SP 2537383940414243444546474849505152535455565758596061626364

CORROSION COUPON ACCESS FITTING

PROJECT

DATA SHEET FOR CORROSION COUPON ACCESS FITTINGMANUFACTURER:SERVICE:PRODUCED WATERSIZE:2"1TAG NO. 23DESCRIPTIONSPECIFICATION REQUIREMENTVENDOR'S CONFIRMATION4GENERAL DATA5ACCESS FITTING TYPE:RETRACTABLE, INTRUSIVE, MULTI STRIP TYPE6ASME CLASS / RATING:150#7END CONFIGURATION:FLAREWELD, 6000#8PIPING CLASS:A1E9CORROSION ALLOWANCE:3 MM10BODY TYPE:NON-TEE TYPE WITH SOLID PLUG ASSEMBLY AND HEAVY CS11PROTECTIVE COVER 12STRIP HOLDER:SUITABLE FOR HOLDING THREE STRIPS FOR TOL, MOL13& BOL MONITORING14INSTALLATION / MOUNTING:AT 12 O CLOCK POSITION ON HEADER ABOVE GROUND 1516HEADER PIPE DETAILS:As per MTO17181920MATERIALS21BODY :A10522INTERNALS:SS31623PROTECTIVE COVER :A10524STRIP / COUPON:SAME AS HEADER PIPE MATERIAL OR EQUIVALENT25STRIP HOLDER :SS 31626PRIMARY PACKING:PTFE27O-RING:VITON (ANTI EXPLOSIVE DECOMPRESSION TYPE)28PIPE PLUG:SS3162930CODES AND STANDARDS / TESTING / CERTIFICATION 31DESIGN CODE:PRESSURE RETAINING PARTS AS PER ASME B31.332FACE TO FACE DIMENSIONS:AS PER MANUFACTURER'S STANDARD33HYDRO STATIC TEST:1.5 TIMES OF DESIGN PRESSURE (MINIMUM)34NDT. (MPI / DP / RADIOGRAPHY / UT ETC.):AS PER ASME B 31.335MATERIAL CERTIFICATION :EN 10204 TYPE 3.136PAINTING:AS PER MANUFACTURER'S STANDARD3738MARKING:MSS SP 2539404142434445464748495051525354555657585960616263

Notes

PROJECTAHDEB OILFIELD SURFACE FACILITIES DEVELOPMENT PROJECTPROJECT NO.401910DOCUMENT NO.AHD-GEN-L-DS-00010AREAGENERALPAGE NO.23OF23DOCUMENTDATA SHEET FOR CORROSION COUPON ACCESS FITTINGREV.: 1MANUFACTURER:SERVICE:SIZE:QTY:123NOTES:41The corrosion coupon access fitting shall be suitable for inserting or retrieving the coupons while the line is in operation.5The corrosion coupon shall allow safe operation and be of a compact design requiring minimum clearances.672Vendor shall consider the corrosion allowance (as indicated) in its calculation as a minimum.893Vendor shall submit the catalogues and its relevant calculations as part of its offer.10114TOL, MOL & BOL Monitoring stands for Top of Line, Middle of Line & Bottom of Line Monitoring. 12135The Corrosion Inhibitor Injection Access Fitting shall be suitable for inserting or retrieving the injection quill while the line is in Operation. 14The injection quill shall allow safe operation and be of a compact design requiring minimum clearances.15166Only Corrosion Inhibitor Injection Access Fitting with single forged or welded tees are acceptable. Threaded tee fittings are not accepted.17187Vendor to quote for the retrieving tool aswell.192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263

Internal Ctrl. No.: 401910-GEN-EP17-010