types ssv-t and ssc-t relays for class ie ......westinghouse i.l. 41-766.5a types ssv-t and ssc-t...
Post on 11-Mar-2020
0 Views
Preview:
TRANSCRIPT
Westinghouse I.L. 41-766.5A
TYPES SSV-T AND SSC-T RELAYS FOR CLASS IE APPLICATION
CAUTION: Before putting relays into service, remove all blocking which may have been inserted for the purpose of securing the parts during shipment. Make sure that all moving parts operate freely. Inspect the contacts to see that they are clean and close properly, and operate the relay to check the settings and electrical connections.
APPLICATION These relays have been specially designed and
tested to establish their suitability for Class IE applications. Materials have been selected and tested to insure that the relays will perform their intended function for their design life when operated in a normal environment as defined by ANSI standard C37. 90 - 197 1, when exposed to radiation levels up to 104 rads, and when subjected to seismic events producing a Shock Response Spectrum within the limits of the relay rating.
"Class IE" is the safety classification of the electric equipment and systems in nuclear power generating stations that are essential to emergency shutdown of the reactor, containment isolation, cooling of the reactor, and heat removal from the containment and reactor, or otherwise are essential in preventing significant release of radioactive material to the environment.
The solid state types SSC-T current relay and SSV-T voltage relay are high seismic relays and suitable for nuclear power staion relaying protection. They are adjustable over a wide range of current and voltage and have a calibrated scale plate which indicates the pick-up setting. The output unit is a telephone relay and an ICS (Indicating Contactor Switch) seal-in device.
The type SSC-T and SSY-T relays have a high ratio of drop-out and are particularly suitable for use in applications requiring an accurate current or voltage level detector.
CONSTRUCTION
The type SSC-T or SSV-T relay consists of a printed circuit board with a transformer, a scale plate, an output telephone relay, and several associated components. The relay is mounted in the semi-flush FT- 1 1 Flexitest case. The relay also includes one ICS (Indicating Contactor Switch) for indication and seal-in purposes. The relay chassis is draw-out construction for easy of test and maintenance.
The components are connected as shown m Fig. 4, 5, and 6.
Input Transformer - The input transformer is a two winding type with a center tapped secondary winding. The secondary is connected to two full wave rectifiers.
Rectifiers and DC Power Supply - There are two full wave rectifiers. One with two zener diodes and a capacitor is used as an input signal and connected to a level detector (setting) circuit. The zener diodes are also used as surge protections. The other full wave rectifier is used as de power supply. For type SSC-T overcurrent relay, a resistor-zener diode is needed in order to keep the current transformer's linearity.
Setting Circuit - The setting circuit is connected between zener-rectifier and sensing circuit.
All possible contingencies which may arise during installation, operation, or maintenance, and all details and variations of this equipment do not purport to be covered by these instructions. If further information is desired by purchaser regarding his particular installation, operation or maintenance of
his equipment, the local Westinghouse Electric Corporation representative should be contacted.
SUPERSEDES I.L. 41-766.5 DATED NOVEMBER 1977 EFFECTIVE FEBRUARY 1984 www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
I.L. 41-766.5A
It consists of two resistors and a potentiometer with a scale plate. The potentiometer has a locking feature to minimize accidential change of setting.
Sensing Circuit - The sensing circuit consists of a transistor, a zener diode, and several associated components. It is actually a level detector. If the input voltage from the rectifier is high enough to break down the zener diode, the output transistor will be turned on.
Output Circuit - The output circuit consists of a transistor driver and a telephone relay. The overcurrent relay (SSC-T) has a telephone relay equipped with 2-A type contacts. The over or under voltage relay (SSV-T) has a telephone relay equipped with 1-A and 1-B t ype contacts.
Indicating Contactor Switch ( ICS) - The Indicating contactor switch is a small de operated clapper type device. A magnetic armature to which leaf-spring mounted contacts are attached. It is attracted to the magnetic core upon energization of the switch. When the switch closes the moving contracts bridge two stationary contacts completing the trip circuit. Also during this operation, two fingers on the armature deflect a spring located on the front of the switch which allows the target to drop. The target is reset from the outside of the case by a push rod located at the bottom of the cover.
OPERATION
The block diagrams of the SSV-T and SSC-T are shown in Fig. I, 2, and 3 and the internal schematic are shown in Fig. 4, 5, and 6. For overvoltage and overcurrent application, the transistor Q2 is normally not conducting and the telephone relay is deenergized. The transistor Q I is used as an emitter follower. When ac voltage or current is applied to the primary of the transformer (T) a voltage is produced on the secondary side that is proportional to the input. The potentiometer ( R2) is for the pick-up setting. If the voltage from rectifier (Z I, Z2, and C2) is large enough to exceed the breakdown voltage of zener diode Z5, the zener diode conducts to turn on the transistor Q2 and operate the telephone relay.
2
For undervoltage application, the transistors Q I and Q2 are normally conducting and the telephone relay is pulled in. As soon as the input voltage drops below the setting, the transistor Q2 is turned off and the telephone relay is released.
CHARACTERISTICS
1. Overcurrent Relay SSC-T
Range
0.5- 2 amps 2.0- 8 amps 4.0- 16 amps 10- 40 amps
Continuous Rating
2 amps 8 amps
10 amps 10 amps
1 Second Rating . . . . . . 28 times the continuous rating
Operating Frequency ... 50/60Hz
Temperature Error . ... 2% between- 20°C and 65%C.
Dropout Ratio . . .. .... 90% to 98%
Response Time . . . . . . . Pickup Time =
10-13 ms Dropout Time =
10-16 ms For 2 to 15 times pickup setting value (Fig. 1 0)
Transient Overreach 5%
Burden . . . . . . . . . . . . . Table I
Frequency Response ... Fig. 12
2. Over/Undervoltage Relay SSV -T
Range . . . . . . . . . . . . . . 60- 140 Volts 140- 320 Volts 280- 640 Volts
www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
Continuous Rating . .. . Highest voltage of range setting.
Operating Frequency .. . 50/60Hz.
Temperature Error ... . 2% between -20°C and +65°C
Dropout Ratio . . . . .. . . 92% to 9 9%
Response Time . . . . . . . Pickup Time -7-10 ms Dropout Time -14-40 ms (Fig. 9)
Burden .. . . . . . . . .. . . 1 VA at 120 volts 60 hertz
TABLE I (60 hertz)
Pickup Current Setting
Range (Amps) Lowest Setting Highest Setting
VA P.F. Angle'/ VA P.F. Angle_i
0.5- 2.0 0.5 8.5° 4.0 12.SO
2.0- 8.0 0.5 8.5° 5.0 12.5°
4.0- 16.0 0.5 8.5° 5.0 12.SO
10.0- 40.0 0.8 10.0° 8.0 10.7°
Trip Circuit The main contacts will safely close 30 am
peres at 250 volts de and the seal in contacts of the indicating contactor switch (when supplied) will safely carry this current long enough to trip a circuit breaker. The indicating contactor switch (when supplied) has a pickup of approximately 1 ampere. Its de resistance is 0. 37 ohms.
SETTINGS
The relay must be set for the desired levels of voltage or current. The pickup of the relay is made by adjusting the potentiometer in the front of the relay. Setting in between the scale marking can be made by applying the desired voltage or current and adjusting the potentiometer until the telephone relay operates.
I.L. 41-766.5A
INSTALLATION
The relays should be mounted on switchboard panels or their equivalent in a location free from dirt, moisture, excessive vibration and heat. Mount the relay vertically by means of the four mounting holes on the flange for the semi-flush type FT case. The mounting screws may be utilized for grounding the relay. External toothed washers are provided for use in the locations shown on the outline and drilling plan to facilitate making a good electrical connection betweer the relay case, its mounting screws and the relay panel. Ground Wires are affixed to the mounting screws as required for poorly grounded or insulating panels. Other electrical connections may be made directly to the terminals by means of screws for steel panel mounting.
For detail information on the FT case refer to I. L. 41-076 for semi-flush mounting.
ADJUSTMENT AND MAINTENANCE
The proper adjustments to insure correct operation of this relay have been made at the factory and should not be disturbed after receipt by the customer.
Acceptance Tests
The following check is recommended to insure that the relay is in proper working order. Refer to the internal schematics and apply voltage or current to the proper terminals.
1. Minimum Trip Current - Check pickup at minimum and maximum settings. This is accomplished by applying the specified voltage or current and checking the pickup of the output telephone relay when the ac input is within ±5% of the settings.
2. Dropout Ratio - After checking pickup, gradually reduce the input. The dropout should be greater than 92% and 90% of the pickup for SSV-T and SSC-T relays respectively.
3 www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
I.L. 41-766.5A
Indicating Contactor Switch (ICS)
Close the main relay contacts and pass sufficient de current through the trip circuit to close the contacts of the ICS. This value of current should be not greater than ICS's rated current. The operation indicator target should drop freely.
The contact wipe should be approximately 0.016 inches. The bridging moving contact should touch both stationary contacts simultaneously.
ROUTINE MAINTENANCE
All relays' calibration should be checked and contacts should be cleaned at least once every year. A contact burnisher S#I82A836HO I is recommended for cleaning purpose. It is recommended to change the potentiomenter R2 every ten years.
CALIBRATION
Use the following procedure for calibrating the relay if the relay adjustments have been distrubed. This procedure should not be used until it is apparent that the relay is not in proper working order. A new scale plate may be necessary when parts are changed.
Dial Calibration - I. Connect on ohmmeter across proper relay terminals which connect to the telephone relay contacts. 2. Apply the desired voltage or current to relay terminals 8 and 9. 3. Turn potentiometer on front of relay counterclockwise from extreme clockwise position until the relay operates as indicated by the ohmmeter.
Indicating Contactor Switch (ICS) Initially adjust unit on the pedestal so that
armature fingers do not touch the yoke in the
4
reset position. This can be done by loosening the mounting screw in the molded pedestal and moving the ICS in the downward position.
I. Contact Wipe - Adjust the stationary contacts so that both stationary make with the moving contacts simultaneously and wipe I /64" to 3/64" when the armature is against the core.
For double trip ICS units, adjust the third contact so that it makes with its stationary contact at the same time as the two main contacts or up to I /64" ahead.
2. Target - Manually raise the moving contacts and check to see that the target drops at the same time as the contacts made or up to I/ 16" ahead. The cover may be removed and
the tab holding the target reformed slightly if necessary. However care should be exercised so that the target will not drop with a slight jar.
3. Pickup - Unit should pickup at 98% of rating and not pickup at 85% of rating. If necessary the cover leaf springs may be adjusted. To lower the pickup current use a tweezer or similar tool and squeeze each leaf spring approximate equal by applying the tweezer between the leaf spring and the front surface of the cover at the bottom of the lower window.
If the pickup is low the front cover must be removed and the leaf spring bent outward equally.
RENEWAL PARTS
Repair work can be done most satisfactorily at the factory. However, interchangeable parts can be furnished to customers who are equipped for doing repair work. When ordering parts, always give the complete nameplate data.
www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
INDICATING CONTACTOR SWITCH
TELEPHONE RELAY
RED HANDLE
TERMINAL
(3516A 14).
Fig. 1. Block Diagram of the Type SSV-T Relay in the Type
FT-11 Case
INDICATING CONTACTOR SWITCH
INDICATING
CONTACTOR SWITCH
I.L. 41-766.SA
CURRENT TEST JACK
TERMINAl..
CHASSIS OPERATED SHOR'TlNG SWITQ-1
(3516A 15).
Fig. 2. Block Diagram of the Type SSG- T Relay in the Type
FT-11 Case
REO HANDLE
CURRENT TEST JACK
TERM IN�
(3517A80).
Fig. 3. Block Diagram of the Type SSG- T Relay (Double Trip)
5 www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
I.L. 41-766.5A
6
3 -------� r--l!------{:
.. +� ,----=---------1 I
� � Z2
l T
3 1;
CJ<o
.. "'
1
$ t--01
�----!4J -1...--{""' 02
I ��Z4
� C3 Z6t- I I I
-® ICS
1-----0
ICS
10
L ________________ �UIC82�d
Fig. 4. Internal Schematic of the Type SSV- T Relay
*ri4�5�17CB�2�G� 072.-�2 -�8�A7M�P7 S--� S�S �C�"� 1451C82G03 .5 2 AMPS SSC-T 1451C82GD4 4 16 AMPS SSC-T 1451CB2G05 10-40 AMPS SSC-T
® ®
liCS (i)
rig 5. Internal Schematic of the Type SSG- T Relay
CAPAC I TOR
C3 Cl-2
l>10DE
01-2
.JUMPER
JI,J2 TRANS! ST0R
QJ-2
RESl ST0R
R9 R>
R7 •• ••
ZENER
Z4 zs Zl-2 Z6
TEL£ RELAY ssv
POT R2
CAPAC I T0R
C3
Cl-2
UI0DE
DJ-4-5
UJ-2
POT R2
QJ-2
RESI ST0R
R3
R5 R7 RB
•• .. Rl
ZENER
Z3 zs z 1-2
Z6
TELE. RELAY
sse
DESCRIPTION STYLE Nl1o o<470UF >OV 762A680H04
J.QOOUf' 200V 876A<409HIO
DESCRI PT 10N STYLE N0o
IN4821 188A342HI6
DESCRI PTI0N STYLE N8o
0 0HM RESI ST0R 862A478HOI
DESCHIPT10N STYLE N0• 2Nl711 762A58SH08
DESCR1PTI 0N STYLE Nlih
saoo.o �sow 2% 629�53JH49 620QoQ 0 sow 2% 629A53JHSI
JO.QK • sow 22 629ASJIHS6. 36o OK 0 sow 21 629AS31H69
IOQ.QK 0 50\11 21 629A53tH80
DESCHIPT10N STYLE N8o
IN9658 24 v 186A797 HOB IN52J5B 6o8V 862A288H07
L5K£200 200o OV 878A619HOI INJOJSB 4J.OV 188A302H08
541D514H33
15K 763A560H21 CuM . LO�AT ON __ ---- -�"I<>AI
BLOCK DIAGRAM _______ 3516AI4
UESCRI PTI0N
• 470UF 50V
I • OOOUF 200V
DESCRIPT10N
IN914
IN4B21
IOK
DESCIUPTI0N
2N l71 1 DESCRI PT10N
JOOOoO • 501W 2%
6200· 0 • sow 2%
10. OK 0 sow 21
4JoQK • sow 2% IOO.QK • sow 21 470 .Q • sow 2%
620oQ SoOQW .. DESCRIPTION
IN2986B 24 V 1N523SB 6o8V
I,SKE200 200 • OV IN3036A 47.QV
(7758589).
STYLE NO.
762A6BOH04 I:J76A409HIO
STYLE N0o
I:JJ6A928HOt
188AJ42H16
763A560H20
STYLE N0. 762A585H08
STYLE N0o 629AS31H.43 629A531HSI
629A531HS6 629A531H71 629AS31H80 629A531 H24 837A23JH03
STYLE NBo
629A79BH03 862A288H07
878A619HO/ 184A449HOS
54t0514H24
COMP LOCATION ____ 3516AI8 BLOCK OIAGRAM ____ 3516AI5
(7758590).
www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
I.L. 41-766.5A
Ut::>Cr<I<"TIO:II
•470Ui ':>OV
I·OOOUF 200V
OESCRI PTI _, .... IN9141
P�4821
STYlE N'-1� 762A680H04 tl76A409HIO
ST (Lf.: NQ,. 6 Jo;M�2HHOI l:::ldAJ42Hl6 r-��--+---------+------- -
IOK VLSCrH PTI (}N
2:'111711
Ot:SCrHPTI�N
3000· 0 ·SO\. 2%
6200 • 0 • ::.0:0. 2I
10-0r< • so .. 2%
43.Qt'( • SJ\.' 2t 100-01( • su .. 2%
47Q.Q -SO ... 2I
6£o.a s.oo• 11
Dt::SCtd PTI ON
IN2966B 24V IN52356 6·�V
1.51<£200 200· ov IN3036A 47.QV
763A560H20
STYLE ,..,0,. 762AS'ISH08
STYLE N0. 62?:r.SJIH43
6�'.>ASJIH51
62H.:.JII-IS6
6?-:; �5311"171
62YA')JJHSO
629AS31 H24
037A2JJ.-10J
STYLE :'�!So 629A798H03
862A2ddrl07
878A619HOI
164A449H05
541DSI4H24
COMP LOCATION . __ 3516A18 BLOCK DIAGRAM_ ... 3517ABO
(7758758).
Fig. 6. Internal Schematic of the Type SSG- T Relay (Double Trip)
0
N "'
"' u u
0
(3516A 17).
Fig. 7. Component Location on SSV- T Module
(3516A18).
Fig. 8. Component Location on SSG- T Module
7 www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
I.L. 41-766.5A
en 0 z 0 0 1&1 en ...J ...J ::IE z 1&1 ::IE t=
8
50
45
40
35
30
25
20
� 15 -
10
5
0 0
I I(
J
I !/ �
� V'
20
TYPICAL T IME CURVES OF THE
/
/ �
/ / �
40
TYPE SSV- T RELAY
( R A NGE 60-140V .)
� lL"
/ .... v
� v /
I --.
60
VOLTS
v
J z
� ....
v
/
I I I
v I -
80
• I
,
L..,...
CURVE NO 619506
80 V. DROPOUT SETTING
(INITIAL VOLTAGE= 120V)
IOOV. DROPOUT SETTING
(INITIAL VOLTAGE= 120V)
80V. PICKUP SETTING
(FINAL VOLT AGE = 120 V. )
IOOV. PICKUP SETTING
(FINAL VOLTAGE =120V.)
100 120
(619506)
Fig. 9. Typical Operating and Reset Time Curves of the Type SSV- T Relay
www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
(/) 0 z
26
25
24
23
22
2 I
20
19
18
17
0 16 0 w (/) ...J 15 ...J :I; � 14 w :I; I- 13
12
I
10
9
8
0 1: 0
I.L. 41-766.SA
CURVE NO. 619507
, �
�
/ v
I I " -
TYPICAL O PERATING AND RESET
I TIME CURVES OF THE T YPE
SS C-T RELAY
(RANGE 2-8 AMPS)
r r- RESET TIME • *
NO TE : CURRENT REDUCED T O ,. 0% OF PICKUP AND INTER-
RUP TED AT CURRENT ZER O.
\I/ t-- OPERATING TIME
""
2 3 4 5 6 7 8 9 10 II 12 13 14 15 MULTIPLES OF PICKUP VALUE
(619507).
Fig. 10. Typical operating and Reset Time Curves of the Type SSG- T Relay
9 www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
I.L. 41-766.SA
10
v 0 I() en iD 0 z ..... > a: ::> (.)
•
.
I 9
: I ' I ! !
II I II I I i ; I i! II I I I\ l i I i : l i > ..... 0 > Q a:
::> II (.) t!l 0 z
� c::i 1-1- .....
VI I > ::i VI � VI
i I: I I j' i 'cj' i ��' !'-! i i
·· · IHI �fH+
i • I! I i
I i
. . - -. 1- -- - - - � -
I! I
I ! I
VI ..... > 0:: ::> (.) ..... (.) z 0 0.. VI ..... 0:: >-(.) z ..... ::> 0 ..... 0:: LL
> 0 ! I
0 <D >-<( ...J ..... 0:: 1-I >
VI VI
0:: 0 LL
. I' '\.''. � l :
I : · i'-' 1 � - t : : i --_!_:_ f . i
I·
i l
li 'i I i
l t 1 I i! I;, .
i . ,.:-;
H H \H+J-++-'\. I II: ! I! i '\." '-i '·' "i !!·'! · i i· '· i '-i '
I I . ·� ·'-, I i i-i ' ' • i i • \. • � . . . . . i·i.i I .L'�c' ! LLLI\, :\.: . ' ' . •. . u i
I ' if t t; I ! I ! 1 i :! � L ! i j-f:[! ! I i:
I i 1 ':"" i ! i : : : ! i; \-\ i l-1 I ·� I, tr l 1 ;.c -� · §= ::t' ·
']�[fl1tlllJJJJilllttll1lJJJJJilllllllJlJJ!llll11lllJJJlllllll�ll-J+lJilll111lil � Q dn>l:lld Z.1ij3H 09 � 0 0 o o 0 .:10 .1N3:lij3d Nl dn>l:lld N - Q en fD
N 1-0:: ..... X
(619504).
Fig. 11. Typical Frequency Response Curve of the Type SSV- T Relay
www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
LO 0 LO 01 (j)
0 z LIJ > a: ;:) 0
I.L. 41-766.5A
��::::+r+l+l+J4J4����p:p:��----�++++++++44��=P,C·�· ����II:+=:I:�:JJl I I! I I I I I ! ! ! ! I :!
.
I 9
II 'i I I' I I I I I I iiI i I': 'i ''' i 11'1 II I I I I I I I I iI I iII i i ' I! i i i i I II I l !Ill I I I 1 I i I I I I l
*� -t++t I.L+ � +- � � - li-t-'- +c-t+ -t-1--i+ -H-t-t- -f-+·;-t
I • I , ,
: : : +:-I ':-·H-�Hi-HH a � 1+1--+-H-++++-1++++++. -�-· -+' +l-+:-H�_,:_,w + : : :- + : : ' - jcJ:I JJll I ;:) c;: - - - 'c:J -- : 1� �·J� + I I ' o.: (!) - - - - - - - - - - - !
z EEEEEtEE88��HHBHFH���������� 1;-i= - - - - - - -�=�= ·=.::·
1--+-H-H-++++++++++++++++-H� �� H-++�-���-+�+_+�+-�+_+=+:+.++++-H�-H�_l--+-_�_H-_l·_���-�:�:+_+_+_+=+_ 1
!I i I ! I I I I II I I ! I I
! I I 11 11 I I -:T'-i- .LL I I ' I i I
I I : ! I ' ' I ! I JJ.I ' ' i I I ! I ! i I i I I I I i I I : fi_l ! I i i I Ll
(/) - -- -i I ' I
I I i ' I i i 'i I ' ' ! i i ! ' I I 1
,, ' I �I I ' I J I I I '
I I i I I I·: -!
I I
: I I i I i!
I
i I I
! I. --J-
i • :I
-+++f·++-it+'-+-'-H-H-+'-+1-H-+-+..L.+:+I-1-l- Jti+-H-H-I+�if- I.JILi'i-!:Li:c-1 I I
II H- 'I ! I ll '' t! :iII I; II I I I 1 . 11 1 : 1· , : I , : , , ' , 1 r 1 1 1 r TT 1 1 1 11 .
-- -U -"' •1. -1-+' -i--J-f-+-T-+-,..,-J.;-H..L.ii-1L.L' L1 L.l 1-+--'--"-- c 1-l..i_-'--,-+-i I�' i i: I ;Ti '
_ 1-. _ II' 'lcj i -- -- - - - · -
� 2
----·0 dn>l:>ld ZJ.�3H 09 LO 0 LO
.:10 !N3:>�3d Nl dn>l:>ld � Q ,._
N 1-a: LIJ :J:
(619505).
Fig. 12. Typical Frequency Curve of the Type SSG-T Relay
11 www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
I.L. 41-766.5A
DIMENSIONS IN INCHES -i6.375 DIMENSIONS IN MM (161.93)
, . 3.188 ••
(80,98) I
PANEL LOCATION �
SEMI-FLUSH MTG. �
.563 (14.30)
tl��)OIA, 4 HOLES FOR ' ,190-32 MTG. SCREWS
PANEL CUTOUT 8 DRILUNG FOR SEMI- FLUSH t.ITG.
(3519A65).
Fig. 13. Outline and Drilling Plan for the Type SSV-T and SSG-T Relay in Semi-Flush FT-11 Case
WESTINGHOUSE RELAY- I NSTRUME NT DIV ISIO N
ELECTRIC CORPORATION CORAL SPRI NGS, FL 33065
Printed in U.S.A. www . El
ectric
alPar
tMan
uals
. com
www . El
ectric
alPar
tMan
uals
. com
top related