torque, hub and hollow shaft calculation

1 2014|01 • www.ringfeder.com

Manual calculation program

Torque, hub and hollow shaft calculation Manual calculation program · 2014 | 01

Torque, hub and hollow shaft calculation

  Enter the address www.ringfeder.com

  If doesn´t exist any registration, you can register first on the left side under “Login”.

  Fill all the information marked with a red star, please with goodness.

  Once you are registered, you go with the mouse on the left side to "calculation" where you can by pressing the left mouse button able to open the page.

  Now select a product („locking assemblies“ or „locking elements“).

  Now select a model by clicking on "Product details and sizes."

  Now when you view this page, you can step into the calculation program using the red "Calculation" button.

  This screen appears next. Now select on the top right the language.

  Now you can open a selection window and decide with the respective hooks which product ("Locking Assembly " or "Locking elements ") or series you need.

  Now you have to choose between torque, hub and hollow shaft calculation. As an example, now the transmissible torque calculation for locking assemblies was applied.

  Now select an appropriate size with the mouse itself. This is done by providing a complete line turns green and it retains.

  Now select an appropriate torque (TA) for the screws of your chip set. It must not be greater than ”TA max" and not less than ”TA min". Tap the number into the blank field and then press "Calculate”.

  The result is shown below. You can now calculate the appropriate hub by clicking below on "hub.”

  The result, for the hub pressure was applied and color-coded. Now you can enter the appropriate yield point, number of axial bores and the factor "C".

  The factor "C" consists of three values : [0.6, 0.8, 1]. To find the right value, you must identify the appropriate condition. For example: With or without axial bore, number of locking assembly, length requirement of the hub.

  Once you have decided on appropriate values, press the green button labeled "Calculate". You can now get the minimum hub outside diameter.

  You can after each of their calculation, store them in a project. Give the project a name and a comment if you want and press "Save".

  You get all the details back in PDF format. Jump to the last page or back?

  Now select a model by clicking on "Product details and sizes."

  Now when you view this page, you can step into the calculation program using the red "Calculation" button.

  This screen appears next. Now select on the top right the language.

  Now you can open a selection window and decide with the respective hooks which product ("Locking Assembly " or "Locking elements ") or series you need.

  Now you have to choose between torque, hub and hollow shaft calculation. As an example, now the transmissible torque calculation for locking elements was applied.

  Now select an appropriate size with the mouse itself. This is done by providing a complete line turns green and retains.

  Now select an appropriate number of screws and then the appropriate coefficient of friction (for the series consisting of stainless steel).

  Now choose a suitable property class, an appropriate screw size. Then go with the mouse on the green button with the words "Calculate" and press it with the left mouse button.

  At the bottom of the page, you get the result. Please ensure that the form is greater than the pressure wave!!

  You can after each of their calculation, save them in a project. Give the project a name and a comment if you want and press "Save".

  You get all the details back in PDF format.

  You can unsubscribe at the top right by moving the mouse on "Logout" and press the left mouse button.

Thank you for your attention !

torque, hub and hollow shaft calculation

Documents

full page photo - careerindia...further the weight of the...

printed in germany 11 - lenzelenze.org.ua/pdf/geared...

internal torque in a shaft - · pdf fileinternal torque in a...

hollow-shaft encoder with diameter of 40 mm e6h-c1...

high torque shaft-shaft and shaft-flange couplings - etp

multiple shaft torque distribution gear box 1 to 1 gear...

lp series | model lp35 · 2018-08-20 · page 2 copyright...

vertical hollow shaft motors - tlp equipment ·...

umschlag g-motion motec en -...

motion-control nc61 chap08 english 2010.book seite 1 ... ·...

wyoming public utility shaft breakage torque study

ecn1123 eqn1135 hollow shaft 1ka - heidenhain

vertical hollow shaft motors

hollow shaft resolver - rgbautomatyka.pl · hollow shaft...

for hollow shaft axles and mobile use

torque motors for extruders - grp6.com · torque motors for...

ultrasonic hollow shaft testing system

sb 029 introduction - heidenhainshaft hollow through shaft d...

(som notes vtu link - simply civil · web viewa hollow...

fisher 249w cageless wafer style displacer sensor...the...