thevenin - norton equivalents and maximum power transfer

Circuit Theorems:Thevenin and Norton Equivalents,

Maximum Power Transfer

Dr. Mustafa Kemal Uyguroğlu

Thevenin’s Theorem

Any circuit with sources (dependent and/or independent) and resistors can be replaced by an equivalent circuit containing a single voltage source and a single resistor.Thevenin’s theorem implies that we can replace arbitrarily complicated networks with simple networks for purposes of analysis.

Independent Sources (Thevenin)

Circuit with independent sources

RTh

VTh

Thevenin equivalent circuit

+–

No Independent Sources

Circuit without independent sources

RTh

Thevenin equivalent circuit

Thevenin Equivalent Circuit

Basic steps to determining Theveninequivalent are– Find vTh RTh

VTh+–

i = 0 i = 0

+

Voc

-

+

Voc

-

Linear

Two-terminal circuit

Voc = VTh

Thevenin Equivalent Circuit

- Compute the Thevenin equivalent resistance, RTh

(a) If there are only independent sources, then short circuit all the voltage sources and open circuit the current sources (just like superposition).

RTh

Linear circuit with all independent sources set equal to zero.

Rin = RTh

RinRin

Thevenin Equivalent Circuit

(b) If there are only dependent sources, then must use a test voltage or current source in order to calculate

RTh = VTest/Itest

RTh

Linear circuit with dependent sources

Itest

+

Vtest

-

Linear circuit with dependent sources

Vtest

+

-

Itest

Thevenin Equivalent Circuit

(c) If there are both independent and dependent sources, then compute(i) RTh = VTest/Itest (all independent sources set equal to zero)(ii) compute RTh from VOC/ISC.

RTh

+–

Linear

Two-terminal circuit

i = isc i = iscVTh

isc = VTh / RTh

Example

Example cont.

Example cont.

Ref.

5 3 5.52 2oc oc

ocV V V V−

+ = ⇒ =KCL at Voc :

Example cont.

Example cont.

Problem: for the following circuit , determine the Thevenin equivalent circuit.

Solution:Step 1: In this circuit, we have a dependent source. Hence, we start by finding the open circuit voltage Voc = Vab. KCL at node C (5 - Voc)/2 + Voc/4 = 0 Voc = 10 V

Step 2: We obtain the short circuit current Isc by shorting nodes a-b and finding the current through it.

5 = 2 Isc + 3 Isc => Isc = 5/5 Isc = 1 A

Step 3: Find the equivalent Thevenin Voltage and Resistance Vth = Voc = Vab = 10V Rth = Voc/Isc => Rth = 10/1 ΩVth = 10VRth = 10 Ω

Norton Equivalent Circuit

Any Thevenin equivalent circuit is in turn equivalent to a current source in parallel with a resistor [source transformation].A current source in parallel with a resistor is called a Norton equivalent circuit.

Norton Equivalent Circuit

Finding a Norton equivalent circuit requires essentially the same process as finding a Thevenin equivalent circuit.

VTh

RTh

IN RN

Th N NV R I= ThN

Th

VIR

=

+–

Th NR R=

Thevenin/Norton Analysis

1. Pick a good breaking point in the circuit (cannot split a dependent source and its control variable).

2. Thevenin: Compute the open circuit voltage, VOC.Norton: Compute the short circuit current, ISC.

If there is not any independent source then both VOC=0 and ISC=0 [so skip step 2]

Thevenin/Norton Analysis

3. Calculate RTh(RN) = Voc / Isc4. Thevenin: Replace circuit with VOC in series with RTh

Norton: Replace circuit with ISC in parallel with RTh

Note: for circuits containing no independent sources the equivalent network is merely RTh , that is, no voltage (or current) source.

Only steps 2 & 4 differ from Thevenin & Norton!

Maximum Power Transfer

I

Maximum Power Transfer

Power delivered to the load as a function of RL.

Maximum Power Transfer

Maximum Power Transfer

Example

Example cont.

Example

Example cont.

17 6 5 172 2 33 2 6 3

6 32 64 12.85 3 5

Th ThTh

Th

V V V

V V

+ ++ = − ⇒ = − − −

− = = − = −

KCL at the supernode:

Example cont.

Example cont.

Example cont.