system 30 straight...track lengths of 150cm - 300cm are supplied in 1 piece. track lengths of 360cm...
Post on 06-Aug-2020
0 Views
Preview:
TRANSCRIPT
TRACK TECHNICAL DETAILS and FITTING INSTRUCTIONS
19mm
Max 120cm Max 8cm
30mm
Top fix or face fix
S Y S T E M 3 0 B E N D A B L E
S Y S T E M 3 0 S T R A I G H T
B R A C K E T S PA C I N G
Max 60cmMax 60cm
Top fix or face fix with brackets either side of every bend, max spacing 60cm
19mm
30mm
* A bracket is required either side of every bend
B R A C K E T S PA C I N G
* Two brackets are required at the track ends
1
Sales: 0845 465 0101e-mail: info@polesandblinds.com
www.polesandblinds.com
S Y S T E M 3 0 S T R A I G H T
S Y S T E M 3 0 B E N D A B L E
TOP FIXING
Fit track directly to ceiling or top board, using pre-drilled holes
For additional support simply drill more holes into the track using a 4mm drill bit (not supplied)
No brackets required
Fit track directly to ceiling or top board, using pre-drilled holes
No brackets required
When top fixing bendable track, DO NOT over tighten screws as this can deform the track and cause the gliders to jam
TOP FIXING
IMPORTANT
FACE FIX BRACKETS FOR SYSTEM 30
FACE FIX BRACKETS FOR SYSTEM 30
Use pre-drilled holes
2
Front
Back
Front
Back
60mm
42mm 45mm
58mm
Cover
60mm
42mm
58mm
Cover
45mm
Magnet
Magnet
Magnet
Magnet
Magnet
Cover plate
S YS T E M 3 0 S T R A I G H T J O I N E R F I N I A L S
S YS T E M 3 0 B E N D A B L E J O I N E R
Ensure magnet is at the front of the track so that the cover plate will locate correctly
The finials below are for System 30 straight and bendable only
Remove part of the inner plastic section to create space to insert the joiner
Ensure magnet is at the front of the track so that the cover plate will locate correctly
79mm
60mm
33mm
33mm
33mm
20mm
84mm
Square Barrel finial
Collar finial
Cap finial
Ball finial
43mm
Suitable for use with top fix
NOT Suitable for use with topfix
3
C U R TA I N H E A D I N G SWe recommend curtain headings should be underslung for all three tracks to ensure the best operation of the curtains
10mm
B E N D I N G S Y S T E M 3 0
Bend B
Trim here
Trim here
Bend B
Bend CBend C
Bend A Bend A
Window centre
Joiner
The track can be bent around a curved object with a radius of no less than 100mm. We recommend covering the track with a tea towel to prevent scratches.
Bend track until kerfs touch. Do not bend any further
Track lengths of 150cm - 300cm are supplied in 1 piece.Track lengths of 360cm - 600cm are supplied in 2 pieces.Track lengths of 720cm - 900cm are supplied in 3 pieces.
It’s easy to achieve:
FORWARD BENDS REVERSE BENDS CONTINUOUS BENDS
Easy to bend on site at point of installation. No more measuring up and hoping. No transporting awkward and delicate bent tracks
4
Radius 150
Radius 150
Trim off excess track at the track ends4
Bracket spacing - see front page5
Bend from the centre working outwards. Bend A, then B, then C, one side then A-C on the other side
3
B E N D I N G TO F I T A B AY
Identify front and back of track
Insert joiner, pushing the plastic filler down the track and tighten screws2
1
Front
Back
Diagram shows track joiner attaching two track lengths at the window centre
Obect
radiu
s
100mm
Bend towards the straight end NOT LIKE THIS
B E N D I N G S YS T E M 3 0
This method causes internal stress in the track which can cause the gliders to jam
DO NOT try to bend towards another bendOpen end
Open end
Curved object
Curvedobject
Bend track until kerfs touch. Do not bend any further
J O I N I N G A L L T R A C K S
Trim ends and cover with end caps/finials
Uncut factory ends
Uncut factory ends Uncut factory ends
With careful installation gliders will smoothly pass over the track joins. There is no limit to maximum track length
Join together factory cut ends and trim off the excess at track ends only
Place a support bracket as close as possible to the join
Ensure the joins are butted together tightly before tightening lock screws
5
Trim off excess track at the track ends
Bracket spacing - see front page
1
2
3
Sales: 0845 465 0101
e-mail: info@polesandblinds.com
www.polesandblinds.com
top related