single nureva_whispertek_installguide january 21 2016
Post on 26-Feb-2018
215 Views
Preview:
TRANSCRIPT
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
1/12
Whispertek surface single installaon guide
Span Ideaon system
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
2/12
WHAT YOULL NEED
2masking tape Straight edge Laser level 3Roller
Three (3) people toinstall the surface.
TABLE OF CONTENTS
Before you begin
Step 1 - Aligning the surface
Step 2 - Adhering the surface
3
4
7
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
3/12
WhisperTekTMSurface installationhttp://nureva-span.uservoice.com/knowledgebase/articles/603927
70F 21C
Use a pencil to make
a 1/4at the center of
the surface.
To avoid cracking, ensure your surface has reached
room temperature before unrolling. Allow the surface
to rest and flatten for 2 to 3 hours before installation.
BEFORE YOU BEGIN
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
4/12
STEP 1
ALIGNING THE SURFACE
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
5/12
Measure and markUse your laser level to project a line 1above the projected image.
Mark a 1vertical line at the center of
the projected image.
Your marks should extend above theline created by your laser level.
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
6/12
AA BC
Align the surface Secure the surface
Person Aalignsthe top of thesurface with thelaser level line.
Person Baligns thetop and right sideof the surface withthe laser level lineand centerline.
Do not remove the adhesive liner from the back of the surface yet.
Person Cwill tape the entire length of thesurface along the top and bottom edges.
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
7/12
STEP 2
ADHERING THE SURFACE
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
8/12
Remove tape from one half
Person A will remove the tape from
only the right side of the surface along
both the top and bottom edges.
Hold the surface in place
Holding the straight edge vertically, person C will press
the surface firmly against the wall approximately 4-6
to the left of the center mark.
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
9/12
Remove the adhesive liner
Person A will pull the surface away from the wall to allow
person B to reach where the adhesive liner is scored at the
back and remove it from that side of the surface.
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
10/12
1
CC AB
2 3
Begin adhering the surface to the wall
Starting from the center point and moving towards the right, person B will begin
to press the surface against the wall with overlapping up-and-down strokes to
prevent bubbles from forming under the surface.
As person B movestoward the edge of
the surface, person Awill slowly allow thesurface to move backtoward the wall.
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
11/12
Adhere the second half of the surface
Once the first half is adhered, remove the remaining tape and follow the
same process to adhere the second half of the surface to the wall.
-
7/25/2019 SINGLE Nureva_whispertek_installguide January 21 2016
12/12
Roller the surface
Apply pressure to the surface using the 3roller to promote
proper adhesion.
2016 Nureva Inc. All rights reserved. Nureva, Span, WhisperTek and the Span logo are trademarks of Nureva Inc. in the United States, Canada and other countries.
top related