schlage pl7 pl8 privacy latch installation instructions
Post on 17-Jun-2022
3 Views
Preview:
TRANSCRIPT
*829696-00*829696-00
© Allegion 2018Printed in U.S.A.
829696-00 Rev. 05/18-g
A. Cover with Emergency Release Button
B. Cover Screws
C. PL7/8 Mounting Screws
D. Pull Assembly
E. Latch
F. Latch/Deadbolt/Strike Screws
G. Strike
H. Strike Box
J. Push Assembly
K. PL7/8 Mounting Nuts
L. Cover with Thumbturn
M. Lead Washers (Optional)
N. Lead Latch Cover (Optional)
CB
A
D
E
F
HG
J
K
L
Tools for Install
OR
F
N
M
Tools for Preparation
Privacy Latch
PL7/PL8Installation Instructions
Customer Service1-877-671-7011 us.allegion.com
1 Install Privacy Latch1a Use the templates from the back page to check the
holes. L NOTE: If the door holes do not match the template, see the
Door Preparation section on the back page.
Template #1
Template #2
1b For the lead lined model ONLY, install the lead lining.
Push handle Pull handle
Actuator PinCam
CamActuator Pin
Push Pull
PL7 has Thumbturn on Push SidePL8 has Thumbturn on Pull Side
ThumbturnEmergencyReleaseButton
Push
PullLead Washers (2)
Push
Pull
Lead Wrap
Template #1
Template #2 or #3
Standard Strike ASA Strike
OR
1c Install the latch.
1d Position the cams, as shown.
Push handle Pull handle
Actuator PinCam
CamActuator Pin
Push Pull
PL7 has Thumbturn on Push SidePL8 has Thumbturn on Pull Side
ThumbturnEmergencyReleaseButton
Push
PullLead Washers (2)
Push
Pull
Lead Wrap
Template #1
Template #2 or #3
Standard Strike ASA Strike
OR
1e Install the push lever and pull lever. L NOTE: The T turn side must be unlocked!
Push
Pull
1f Place the covers over the levers. Install and tighten the cover screws.
Push handle Pull handle
Actuator PinCam
CamActuator Pin
Push Pull
PL7 has Thumbturn on Push SidePL8 has Thumbturn on Pull Side
ThumbturnEmergencyReleaseButton
Push
PullLead Washers (2)
Push
Pull
Lead Wrap
Template #1
Template #2 or #3
Standard Strike ASA Strike
OR
1g Install the strike. L NOTE: If the frame is not prepared, see the Frame
Preparation section below.
Standard StrikeASA Strike
OR
OR
Standard StrikeASA Strike
OR
2 Frame Preparation2a Use the strike as a pattern to mark the frame.
Standardstrike
ASA strike
ORLatch
Door
Standardstrike
ASA strike
ORLatch
Door
OR
Standardstrike
ASA strike
ORLatch
Door
2b Drill holes.
1¹⁄₄"(32 mm)
1"(25 mm)
¹⁄₂" Deep(13 mm)
Standardstrike
ASA strike
OR
Door
Latch
Standard
Wood - #32 Pilot DrillMetal - #29 Drill, #8-32 Tap
ASA StrikeWood - ¹⁄₈" (3mm) Pilot DrillMetal - #16 Drill, #12-24 Tap
2c Mortise for strike. L NOTE: The strike should be flush to the frame.
1¹⁄₄"(32 mm)
1"(25 mm)
¹⁄₂" Deep(13 mm)
1¹⁄₄"(32 mm)
1"(25 mm)
¹⁄₂" Deep(13 mm)
3 Door Preparation3a Mark the center lines (CL
₈⁄ ⁵1
" m
m 1
4()
Mortise to ⁵⁄₃₂" (4 mm) depth
Door Edge
¹⁄₈"(3 mm)
CL
CL
Latch
1¹⁄₈"(29 mm)
1" (25 mm)Hole
2¹⁄₈"
(54 mm)
Hole
1" (25 m
m)
HoleTemplate #1Push/Pull
Latch
3³⁄₈" (86 mm)
CL
CL
₈⁄ ⁵1
" m
m 1
4()
Mortise to ⁵⁄₃₂" (4 mm) depth
Door Edge
¹⁄₈"(3 mm)
CL
CL
Latch
1¹⁄₈"(29 mm)
1" (25 mm)Hole
2₈⁄¹"
5(4m m)
Hoel
1" (25 mm)
Hoel
Template #1
Push/Pull
Lacth
3³⁄₈" (86m m)
CL
CL
Vertical Horizontal
MinimumBackset
7” (178 mm)
OR
Backset2³⁄₄", 3 ³⁄₄", 5", or 7"
(70, 95, 127, or 178 mm)
CL
CL
CL
45" (114.3 cm)From Finished Floor
Recommended
).
CL
CL
CL
45" (114.3 cm)From Finished Floor
Recommended
Backset2³⁄₄", 3 ³⁄₄", 5", or 7"(70, 95, 127, or 178 mm)
3b Mark the door.
₈⁄ ⁵1
" m
m 1
4()
Mortise to ⁵⁄₃₂" (4 mm) depth
Door Edge
¹⁄₈"(3 mm)
CL
CL
Latch
1¹⁄₈"(29 mm)
1" (25 mm)Hole
2¹⁄₈"
(54 mm)
Hole
1" (25 m
m)
HoleTemplate #1Push/Pull
Latch
3³⁄₈" (86 mm)
CL
CL
₈⁄ ⁵1
" m
m 1
4()
Mortise to ⁵⁄₃₂" (4 mm) depth
Door Edge
¹⁄₈"(3 mm)
CL
CL
Latch
1¹⁄₈"(29 mm)
1" (25 mm)Hole
2₈⁄¹"
5(4m m)
Hoel
1" (25 mm)
Hoel
Template #1
Push/Pull
Lacth
3³⁄₈" (86m m)
CL
CL
HorizontalVertical
MinimumBackset
7” (178 mm)
OR
₈⁄ ⁵1
" m
m 1
4()
Mortise to ⁵⁄₃₂" (4 mm) depth
Door Edge
¹⁄₈"(3 mm)
CL
CL
Latch
1¹⁄₈"(29 mm)
1" (25 mm)Hole
2¹⁄₈"
(54 mm)
Hole
1" (25 m
m)
HoleTemplate #1Push/Pull
Latch
3³⁄₈" (86 mm)
CL
CL
₈⁄ ⁵1
" m
m 1
4()
Mortise to ⁵⁄₃₂" (4 mm) depth
Door Edge
¹⁄₈"(3 mm)
CL
CL
Latch
1¹⁄₈"(29 mm)
1" (25 mm)Hole
2₈⁄¹"
5(4m m)
Hoel
1" (25 mm)
Hoel
Template #1
Push/Pull
Lacth
3³⁄₈" (86m m)
CL
CL
HorizontalVertical
MinimumBackset
7” (178 mm)
3c Drill holes.
3d Mortise for latch.
2¹⁄₈" (54 mm)
Hole
1" (25 mm)Hole
Template #1 CL
CL
1³⁄₄" (44 mm)
3³⁄₈" (86 mm)
⁵⁄₁₆" (8 mm)4 places
₈⁄⁵1
)m
m 14( "
Mortise to ⁵⁄₃₂" (4 mm) depth
Door Edge
2¹⁄₄"
(57
mm
)
CL
CLLatch
1¹⁄₈"(29 mm)
mm 92( "1¹⁄₈ )eloH
Template #2(standard latch)
Wood - #32 Pilot DrillMetal - #29 Drill, #8-32 Tap
1¹¹⁄₁₆" (43 mm)
1³⁄₈" (35 mm)
Additional Notes: Revision History Revision Description:g > Revised artwork
1. None B C D E F g
N/A N/A N/A N/A 075349 XXXXX
MaterialWhite Paper
Edited By Approved By EC Number Release Date
D. Toppins M. Sasso xxxxxx 05-09-18
Notes1. printed two sides2. printed black3. tolerance ± .134. printed in country may vary5. drawings not to scale
Title
INSTALLATION INSTRUCTIONS PL7/PL8 LATCHCreation DateN/A
Number
829696-00Revision
gCreated ByN/A
Activity3899 Hancock Expwy
Security, CO 80911 © Allegion 2018Software: InDesign CS6
8.50017.000
11.00011.000
FINAL SIZEBEgINNINg SHEET
FRONTFRONT
top related