product guide cjv150- 75-107...1,7 3,6 5,4 7,1 8,5 10,5 12 1,9 4,2 6,2 8,2 9,8 12,2 14,3 0 5 10 15...
Post on 24-Dec-2020
0 Views
Preview:
TRANSCRIPT
Mimaki Europe B.V.Sign Graphics Products
The new high quality entry models
Product GuidePrint&Cut
The information in this document is subject to change without notice.
18-11-2014Ver1.1_EU
Mimaki Europe B.V.Sign Graphics Products
Terms of use
• The contents of this presentation are intended only for Mimaki authorized resellers. Authorized persons are not permitted to distribute, copy or change this presentation without explicit approval of Mimaki Europe B.V.
• Contents and technical explanations in this presentation are based on the test results achieved at Mimaki at the time of testing and are not a guarantee for performance. Substrates should be tested beforehand.
• In addition, the contents in this presentation do not lead to any legal obligations from Mimaki and Mimaki does not take any responsibility. Please verify in advance whether your intended prints will result in sufficient quality.
• Contents of this presentation are subject to change without prior notice for improvement. Compositors errors reserved.
Mimaki Europe B.V.Sign Graphics Products
Features
• Mimaki’s technologies delivers high-image quality • Smooth image quality by waveform control and precise dot placement technology• Variable dot printing by 3 different drop sizes of Large/Middle/Small• Mimaki’s proprietary 3-way intelligent heater optimizes dot gain• MAPS3 eliminates banding and delivers smooth print densities
• A wide variety of inks broaden application• Printing exclusive metallic colors with high-intensity silver ink• Wider color gamut printing with orange ink• Light black ink produces accurate grayscale printing without color shifts• White ink achieves high opacity printing
• Versatile Print&Cut functions• Zero margin crop mark reduces the waste of media• Supports thin media such as heat transfer media by Cut & Print function• Dotted line cut function cuts backing sheet leaving a few minimal joints• Over cut and Corner cut functions cut edges sharp even using thick media• Segment compensation achieves accurate long-length cutting• Continuous crop mark detection for unattended Print&Cut operation
3
Mimaki Europe B.V.Sign Graphics Products
System Configurations
4
Options
MBIS3Drying fanAir exhaust unitStatic prevention sheet8x Eco-cartridge for 600ml BS3 inks
Including Rip software
PC
Works also with:
USB 2 0 5m(15ft) cable is recommended
Connection
Recommended specificationsCPU: Core i5 3.2GHzMEMORY: 8GBHDD: 500GBUSB2.0: 4 ports or moreOptical disk drive: DVD-ROMWindows7 Professional 64bit Monitor: 1366x768
Mimaki Europe B.V.Sign Graphics Products
Ink Type / Ink Set
5
10 different ink colors
4 ink set selections①6C+WSi:Silver included
②4C:High speed printing
③8C: Smooth result & vibrant expression
④6C+WW: 6C plus white printing
Capacity:CMYKLcLmLkOr:
440ml cartridge2L Ink pack, for the MBIS3
White and Silver:220ml cartridge
SS21
M C Y K Lc Lm Lk Or W Si
M C Y K K Y C M
M C Y K Lc Lm Lk Or
M C Y K Lc Lm W Si
M C Y K Lc Lm W W
Mimaki Europe B.V.Sign Graphics Products
Ink Type / Ink Set
6
CapacityCMYK:
600ml Ink pack, for the Eco-cartridge2L Ink pack, for the MBIS3
Eco-cartridge needs to be ordered extra
BS3
4 Colors4C :
Ink set4C : High speed printing
M C Y K K Y C M
M C Y K K Y C M
Sb53
7 Colors6C:
*K ink is also available
Ink set4C : High speed printing
6C : Smooth and vibrant colors
CapacityBMYKLbLm:
440ml cartridge2L Ink pack, for the MBIS3
M B Y Dk Lb Lm
M B Y Dk Dk Y B M
M B Y Dk Lb Lm B M
Mimaki Europe B.V.Sign Graphics Products
Head layout
• 1 Print head is incorporated • Ejects 7 different drop sizes of 4pl/7pl/8pl/14pl/16pl/24pl/35pl• Prints both high quality mode and high speed mode
7
Nozzle row lengthApprox.25.4mm(1 inch)
Nozzle widthApprox.31mm(1.2 inch)
1-head:1440-nozzle(180-nozzle x 8-lines)
1 2 3 4 5 6 7 8
Mimaki Europe B.V.Sign Graphics Products
Highly versatile printer
• Larger Ink drop
• 3 different drop sizes are automatically selected from 7drop sizes, depending on the selected print quality (profile)
• When working with SS21, the 7 drop sizes are 4pl,7pl,8pl,14pl,16pl,24pl, and 35pl
• High speed printing with high densities is attained by taking advantage of the maximum drop size of 35pl
• The variable dot technology, with a maximum dot size of 35pl, is used for the highest productivity of 45.4m²/h with SS21/BS3 and 48m²/h with SB53
• This gives the printer a wide coverage, from high resolutions with high qualities to low resolution printing, with higher densities
8
Case 1 : Maximum dot size =21pl Case 2 : Maximum dot size =35pl
Large21pl
Middle14pl
Small4pl
1 /360 inch
1 /360inch
Large35pl
Middle14pl
Small4pl
1 /360 inch
1 /360 inch
Low density due to an gap between the dots↓
Not suitable for high speed mode (low resolution)
High density with no gap between the dots↓
Suitable for High speed mode
Mimaki Europe B.V.Sign Graphics Products
Print Speed (SS21/BS3)
• Ink set: 4C, CMYK
9
PVC Banner
㎡/h ㎡/h
1,7
3,6
5,4
7,1
8,5
10,5
12
1,9
4,2
6,2
8,2
9,8
12,2
14,3
0 5 10 15 20
Super Smooth1440x1440,16P,Bi
High Quality720x1440,12P,Bi
High Quality720x1080,8P,Bi
Standard②720x720,6P,Bi
Standard①720x720,5P,Bi
High Speed720x720,4P,Bi
Draft540x720,4P,Bi
CJV150-107
CJV150-75 4,3
7,1
10,5
12
25
40,245,4
0 10 20 30 40 50
High Quality720x1440,10P,Bi
Standard②720x1080,6P,Bi
Standard①720x720,4P,Bi
High Speed540x720,4P,Bi
Draft540x360,2P,Bi
Super Draft360x360,1P,Bi
CJV150-107
CJV150-75
The print modes in this document is the performance of the printer. The media profiles are created depending on the media type. Creating profiles with MPM II is possible, when the media profile is not available.
Mimaki Europe B.V.Sign Graphics Products
1,3
2,4
2,7
3,6
4,3
5,4
1,5
2,8
3,1
4,2
5,0
6,2
0 5 10 15
Super Smooth1440x1440,20P,Bi
High Quality720x1440,18P,Bi
Standard②720x1080,16P,Bi
Standard①720x1080,12P,Bi
High Speed720x720,10P,Bi
Draft720x720,8P,Bi
CJV150-107
CJV150-75
Print Speed, SS21, 8C/6C ink set
• Ink set: 6C(CMYKLcLm+WW/WSi) / 8C(CMYKLcLmLkOr)
10
㎡/h ㎡/h
PVC Banner
2,4
3,1
4,3
5,4
6,2
12,5
20,7
2,8
3,6
5,0
6,2
7,4
14,3
23,3
0 5 10 15 20 25
Super Smooth720x1440,18P,Bi
High Quality720x1080,14P,Bi
Standard②720x720,10P,Bi
Standard①720x720,8P,Bi
High Speed540x720,8P,Bi
Draft540x360,4P,Bi
Super Draft360x360,2P,Bi
CJV150-107
CJV150-75
Mimaki Europe B.V.Sign Graphics Products
Print Speed, SS21, Silver ink set
• Ink set: 6C (CMYKLcLm+WSi)
11
1-layer printing(Silver only)
Metallic color printing(Silver→Color)
㎡/h ㎡/h
0,17
0,28
0,55
0,19
0,32
0,64
1,40
0 0,5 1 1,5 2
Super Smooth1440x1440,32P,Bi
High Qulaity720x1440,32P,Bi
Standard720x1080,16P,Bi
High Speed720x1080,12P,Bi
CJV150-107
CJV150-750,86
1,39
2,21
0,96
1,60
2,55
3,18
0 1 2 3 4
Super Smooth1440x1440,32P,Bi
High Qulaity720x1440,32P,Bi
Standard720x1440,20P,Bi
High Speed720x1080,16P,Bi
CJV150-107
CJV150-75
*CJV150-75 does not have high speed mode
Mimaki Europe B.V.Sign Graphics Products
0,61
1,39
2,45
3,65
0,69
1,60
2,83
4,22
0 1 2 3 4 5
High Quality1440x1440,32P,Bi
Standard②720x1440,32P,Bi
Standard①720x1080,18P,Bi
High Speed720x1080,12P,Bi
CJV150-107CJV150-75
0,2
0,46
0,81
1,04
0,23
0,53
0,94
1,21
0 0,5 1 1,5 2
High Quality…
Standard②…
Standard①…
High Speed…
CJV150-107CJV150-75
Print Speed, SS21, White ink set
• 3-layer printing is possible with the fast drying SS21 white ink• 10.5 m²/h maximum, when printing white ink only
12
1-layer printing(White only)
2-layer printing(Color → White / White → Color)
㎡/h
3-layer printing(Color → White → Color)
m²/h m²/h
m²/h
0,12
0,28
0,46
0,82
0,14
0,32
0,53
0,94
0 0,5 1 1,5 2
High Quality…
Standard②…
Standard①…
High Speed…
CJV150-107CJV150-75
Mimaki Europe B.V.Sign Graphics Products
Outstanding Speed, Sb53 inks
• Sb53 4C and 6C printing speeds
13
BMYDk(K) BMYDk(K)LbLm
m²/h m²/h
5,0
6,2
8,2
12,2
14,3
20,0
30,0
48,0
0 20 40 60
Super Smooth720x1440,10P,Bi
High Quality720x1440,8P,Bi
Standard②720x1080,6P,Bi
Standard①720x720,4P,Bi
High Speed②540x720,4P,Bi
High Speed①540x360,3P,Bi
Draft540x360,2P,Bi
Super Draft360x360,1P,Bi
CJV150-1072,8
3,6
5,0
6,2
7,4
15,0
24,6
0 10 20 30
Super Smooth720x1440,18P,Bi
High Quality720x1080,14P,Bi
Standard②720x720,10P,Bi
Standard①720x720,8P,Bi
High Speed540x720,8P,Bi
Draft540x360,4P,Bi
Super Draft360x360,2P,Bi
CJV150-107
Mimaki Europe B.V.Sign Graphics Products
Outstanding Speed, Sb53 inks
• 2 different types of black ink• 2 types of black ink are offered to meet customer's demand
14
Type Advantage Disadvantage
Sb53-K
• Less smoke generation, during heat transfer
• Less grainy results can be seen at the low gradation areas
• When printing with 100%, the density is the same as Dk ink, but the density is lower in the areas with low gradations
Sb53-DK• Reflection density is higher at the
low gradation part
• Grainy results can be seen at the low gradation areas
• More smoke generation during heat transfer, compared to the K ink
Mimaki Europe B.V.Sign Graphics Products
High-intensity Silver ink (SS21)
• The Silver ink of SS21 expresses shiny finish• Brightness does not become lower even after laminate film is applied*• Brightness even after 3-year acceleration test is better than ES3
15
①ES3:
Metallic gloss level gets lower when laminated②SS21:
Gloss level is maintained even with laminate
Media:Avery MPI 2000Laminate Film Avery DOL2060 • Initial brightness of SS21 is 67% higher than ES3
• Brightness of SS21 after 3-year acceleration test is still 5% higher than ES3’s initial value
Outdoor resistance comparisonBrightness comparison①Laminated②Initial brightness of ES3 is set as 100%.
167%
137%
123%
105%100%
65%
50%39%
0%
50%
100%
150%
200%
初期 1年相当 2年相当 3年相当
SS21
ES3
*1The scratch resistance of SS21 Silver ink is poor. Laminate is advised.
Initial 1-year 2-year 3-year
ES3 w/ laminate
SS21w/ laminate
SS21w/olaminate
Mimaki Europe B.V.Sign Graphics Products
3-type Metallic Color Collection
• Metallic color is expressed by printing color on silver• 648 metallic colors designed for easy color matching• Target metallic color can be selected from swatch library
• 3-type Metallic Color Collection
16
Type A: Chart Type B: Booklet
Type C: Patch
*Each type of Metallic Color Collection has the same colors.3-type Metallic Color Collections are available in RL6
Mimaki Europe B.V.Sign Graphics Products
Stunning Quality
• New orange ink with SS21
• Wider gamut with new Orange ink
• Orange ink is added as an process color
• Covering approx. 94.8% of the PANTONE coated color chart. 7% more than with 4C only
• The large color gamut makes it easy possible to reproduce corporate colors, etc.
17
M C Y K Lc Lm Lk Or
Mimaki Europe B.V.Sign Graphics Products
-120
-100
-80
-60
-40
-20
0
20
40
60
80
100
120
-120 -100 -80 -60 -40 -20 0 20 40 60 80 100 120
CMYKLcLmLkOr
CMYK
PANTONE近似色
Stunning Quality
• SS21 with Orange ink
18
High reproducibility with bright, fresh
Orange
Less freshness without Orange ink
CMYKLcLmLk+OrCMYKLcLm
Gamut comparison Comparing print results
*PANTONE solid chips coated(1085 colors)
Colors of PANTONE
Mimaki Europe B.V.Sign Graphics Products
Stunning Quality
• SS21 with Light-black ink• High quality Monochrome color reproduction with the new Light-Black ink• Smooth color balance without color shifting, reproducing high quality
monochrome smooth and clear grey output
19
CMYKLcLmLkOrCMYKLcLm
• Clear grey• Smooth skin
• Reddish grey• Skin w/grainy
appearance
• Reddish grey • No color shift and smooth gradation
CMYKLcLmLkOrCMYKLcLm
Mimaki Europe B.V.Sign Graphics Products
Stunning Quality
• High density White ink• Vivid color printing even on transparent/colored media
• By under-laying white ink before printing the colors
• Higher opacity, is attained by using an larger ink droplet
20
Transmission density: 0.36
CJV150
Transmission density: 0.27
Older generation printers
Density comparison (White - single layer)
Density: 33% UPProductivity: 230% Up
Print mode: 720x1440,32P,Bi Productivity: 2.07m²/hMaximum drop size: 24pl
Media: PET
Print mode: 720x1440,32P,Bi Productivity: 0.9m²/hMaximum drop size: 14pl Media: PET
*White – 200% print*Light-up, Mimaki logo underneath
Mimaki Europe B.V.Sign Graphics Products
• Waveform Control Technology for high quality printing
• High accuracy dot placement• Jetting ink drops in straight lines, high accuracy dot placement with
almost perfect round dots
• Generating less mist • Printing clear and sharp letters, lines, edges, etc.
• Waveform is optimized, to reduce the risk of missing nozzles
Stunning Quality
21
Mimaki Europe B.V.Sign Graphics Products
Stunning Quality
22
Ink dots do not overlap and gives an accurate dot placement
↓No grainy appearance
Ejects ink in straight lineswith a near-perfect circle
Ejects ink not straightly and not with a perfect circle
Ink dots overlap and no accurate dot placement↓
Grainy appearance and uneven density
Mimaki Europe B.V.Sign Graphics Products
Stunning Quality
• Variable ink Dot Technology• Printing with 3 different dot sizes, small, medium and large• Delivers a high image printing quality, with very smooth gradations• 3 different drop sizes are selected from 4pl/7pl/8pl/14pl/16pl/21pl/29pl/35pl,
depending on the type of ink and the selected print mode• This allows printing in not only high resolution printing, for high quality, but also
high speed & high density printing for high productivity!
23
Variable dot
Normal dot
Mimaki Europe B.V.Sign Graphics Products
Stunning Quality
• 3Way Intelligent Heater plus Top Blower• Optimizes the dot gain• Generates a higher print quality without bleeding, by a quick and accurate ink dot
fixing, by heating the media to a perfect temperature, through the Pre- and Print heaters
• The Post-heater provides additional drying after printing• The top blower assists drying the ink on the media surface, to support high
speed/density printing
24
3-way Intelligent Heater patent No.
Japan 4889059
USA 8.444.262
China ZL 200910222559.8
Pre-heater
Post-heater
Heater coverPrint-head
Pinch roller
Grid roller
Print- heater
Post-heater to ensures faster drying
Controls drop size by heating up media.
Mimaki Europe B.V.Sign Graphics Products
Stunning Quality
25
Normal PassMAPS3
• MAPS3 (Mimaki Advanced Pass System 3)• MAPS3 prints passes in gradation-like tone, by dispersing ink drops between the
passes, which reduces banding, uneven drying ink, and bidirectional stripes• MAPS3 works in the higher pass modes of an resolution
Mimaki Europe B.V.Sign Graphics Products
Continuous Operation
• NCU (Nozzle Check Unit)
• Stable printing quality, by preventing printing with clogged nozzles
• NCU checks the nozzle condition automatically per transferred file or the set print length
• When nozzles are clogged, the cleaning is then started automatically
• When the clogged nozzle is not recovered by cleaning, the Nozzle Recovery System is then automatically done, and printing starts
26
Mimaki Europe B.V.Sign Graphics Products
Continuous Operation
• NCU (Nozzle Check Unit)
27
Light emitter Receiver
Print headInk ejection by each nozzle line
Sensor:Receiver detects a light → no ink drop →Cleaning
The NCU unit
Nozzle check duration: 50sec./checkNozzle check ink consumption: 192 cc/year**Operating Condition: One check/hour x 10-hour operation/day x 240-day
NCU operation flow
Checks nozzles
Nozzle recovery is then automatically set
Start printing
Warning (Standby)
Yes
No
All nozzles are checked per nozzle line
When missing nozzles could not be recoveredafter retrying cleaning.
The number of the retrying cleaning can
be changed.
Nozzle MissingYes/No
Cleaning is done automatically
Nozzle check setup
1. After printing, one file2. After printing, the set print length
When the number of missingnozzles is higher than the number
in the setup
Mimaki Europe B.V.Sign Graphics Products
Continuous Operation
• NRS (Nozzle Recovery System)
• Increases the uptime
• Replaces missing nozzles, by working nozzles in other passes
• No need for direct service intervention
• Makes printing with the same quality possible, even if nozzles are missing
28
Continuous printing by NRS
Continuous OperationDown Time
Mimaki Europe B.V.Sign Graphics Products
• NRS (Nozzle Recovery System)
Continuous Operation
29
• 10 nozzles can be registered per 1 nozzle line • NRS is not changing the printing speed• NRS is not working when:
• Printing in low pass modes• Printing in some modes with MAPS3 • The position of the nozzle is not correct
Register the number of missing nozzles
Replacing the clogged nozzle, by using a other working nozzle
Nozzle check pattern
Clogged/Missing nozzles
Mimaki Europe B.V.Sign Graphics Products
• Automatic Wiper Cleaning
• The ink on the wiper is automatically removed during the cleaning procedure of the printhead
• No pollution on the print head caused by ink residue from the wiper
• Easier daily maintenance as the wiper is cleaned automatically
Continuous Operation
30
1. Washing liquid
2. Wipe out
Wiper Cleaner
Mimaki Europe B.V.Sign Graphics Products
Continuous Operation
• Event Mail Notification • Various information can be sent from printer via email• Read the status of the printer on remote locations, allowing unattended
printing
31
USB
RIP-PC Mobile device
Print start/completedError/Warning
Internet Receiving Mail
LAN
Mimaki Europe B.V.Sign Graphics Products
Continuous Operation
• MCT (Mimaki Circulation Technology)• Stable white and silver ink supply to the printheads• Circulating the white silver inks in the ink line system • Preventing the settlement of pigments • MCT works only when the white and silver inks are installed
32
Circulates the white and silver ink through the lines
Ink lines
1 2 3 4 5 6 7 8
Pu
mp
Mimaki Europe B.V.Sign Graphics Products
Continuous Operation
• Ink Supply Systems• UISS*(Uninterrupted Ink Supply System)
• In 4C ink-set, when the ink runs out, ink is automatically supplied from the other cartridge for continuous operation
• Not available with 6C/8C ink-set
• Non-Stop Ink replacement• Working with the 4C ink-set, an empty ink cartridge can be replaced with a
new one, without stopping the on-going print job• No waste of time and media or ink• When using the Sb53 6C ink set, UISS works with M and Bl• Not available with 6C+WW and 8C ink sets
• Optional, MBIS3 (Mimaki Bulk Ink System III)• Large volume, 2L ink packs, are placed directly on to
the ink station• Making it possible to print, continuous large print jobs• The new MBIS3 on the printer saves working space,
and large 2L ink pack saves running cost
33
M M KKYYC C
Mimaki Europe B.V.Sign Graphics Products
Media feeding and take-up
• Handles media of up to 40kg
• The take-up roll unit of the CJV150 has a strong torque to feed media of 40kg
• Maximum diameter of up to 250mm
• The height of the take-up roll unit is 17cm, which is high enough to roll up the media of the diameter of up to 250mm
• Prints one roll of media with high feeding accuracy
• The diameter of the taken-up media is measured by a censor
• This keeps the tension of the media constant
34
Take-up roll switchFor manual operation
press the button to roll up the media.
Mimaki Europe B.V.Sign Graphics Products
• Half cut / Die cut / Dotted line cut
35
Cuts a series of half and die cuts leaving a few minimal joints.
Dotted line cutDie cutHalf cut
Cuts through the backing sheet to cut out the individual figures.
Cut out figures leaving backing sheet.
A wide variety of Print&Cut functions
Mimaki Europe B.V.Sign Graphics Products
A wide variety of Print&Cut functions
• Continuous Crop Mark Detection
• Zero Margin Crop Mark*
36
A maximum of four crop marks are automatically andcontinuously detected so that printed images are accurately cut, compensating for distortion in each image
The conventional crop marks require 4mm~10mm margins between crop marks. However, the
margins between crop marks are eliminated by Zero Margin Crop Mark reducing the media waste.
* Available in April, 2015
Conventional Crop Mark Zero Margin Crop Mark
Margin=Waste
Mimaki Europe B.V.Sign Graphics Products
• P&C/C&P without crop mark
• When the production length is less than 1m, P&C is done precisely without using crop marks.
• The unused space is minimized to reduce the media waste.
37
Zero Margin Crop Mark
unused space
P&C/C&P without crop mark
A wide variety of Print&Cut functions
Mimaki Europe B.V.Sign Graphics Products
• Segment Compensation
• Intermediate crop marks of the feed direction are detected, enabling four-point corrections for each segment
• This leads to accurate, long-length cutting, even if the image is distorted
38
Intermediatecrop mark
Intermediatecrop mark
Segment③
Segment②
Segment①
A wide variety of Print&Cut functions
Mimaki Europe B.V.Sign Graphics Products
• Over cut• By overlapping the start and the end point, cutting is done without uncut parts. • Effective when cutting thick or sticky media as well as the ones easy to bend
• Corner cut• The edge of the blade overlaps at other corners. • By using Corner cut, the corners are cut sharp
39
1.0mm
1.0mm
When the length of the over cut is set, cutting is performed from the position before the starting point by the specified length and stops after crossing the end point.Setting value: 0.1mm – 1.0mm
Over cut Corner Cut
1.0mm
1.0mm
A wide variety of Print&Cut functions
Mimaki Europe B.V.Sign Graphics Products
• Cut & Print• Thin media such as heat transfer media is cut without drying
time
40
When the ink is not dried enough…①The edge of peels off ②The cut part sticks together again
Cut before printing allows for…①The edge does not peel off②The cut part does not stick together
again
P&C C&P
No drying time is required.
Drying time is required.
A wide variety of Print&Cut functions
Mimaki Europe B.V.Sign Graphics Products
Auto pull-back printing
• When printing high density colors on silver, a brighter metallic color is created with Auto pull-back printing
41
Workflow with Auto pull-back printing
Green
Metallic blue
Result Image
GreenBlue on topSilver(Spot color)
=②
Automaticallypull-backmedia to
origin
① Print silver and color plate ③ Print colors
for metallic color
Mimaki Europe B.V.Sign Graphics Products
• Automatic media clamp function
• Pinch roller pressure is automatically changed in 4 levels (Strong/Medium/Low/OFF)
• Feed media at the best pressure for each printing and cutting to deliver fine quality
• Full automatic function enables unattended operation without manual intervention from the start of printing to the end of cutting
42
A wide variety of Print&Cut functions
Mimaki Europe B.V.Sign Graphics Products
• Automatic media clamp function• Pinch roller pressure is automatically changed in 4 levels (High/Middle/Low/OFF)
• Feed media at the best pressure for each printing and cutting to deliver fine quality
• Full automatic function enables unattended operation without manual intervention from the start of printing to the end of cutting
• Machine with Automatic media clamp function
• Machine without Automatic media clamp function• Remove pinch roller manually or Always use pinch roller
43
PrintSet media
clamp automatically CutSet media
clamp automatically Print
PrintRemove pinchroller manually
Cut PrintAttach pinch
roller manually
Continuous operation of P&C is possible
Unattended operation of P&C is not possible
A wide variety of Print&Cut functions
Mimaki Europe B.V.Sign Graphics Products
Optimize Work Efficiency
• Highly Visible Design of the Machine• Color LCD Control Panel
• Display size of 52.56mm x 70.08mm • Allowing easy setup and control
• The Status LED• LED status lamp indicates the status of the printer• Easy to see from an distance
44
Various information is displayed in a graphical manner, such as media width, heater temperature and remaining ink
Status LEDBlinking in Blue: Normal operation
Blinking in Red: Needs attention
Mimaki Europe B.V.Sign Graphics Products
Stable printer
• Lift up block• By attaching the Lift Up Blocks to the casters of machine, the
shaking of the machine while printing is prevented.
45
w/o Lift up block w/ Lift up block
Lift up the printer and set Lift up block
Mimaki Europe B.V.Sign Graphics Products
Rip software, RasterLink6
Frequently used setting can be registered as “My Favorite”. Up to 30 settings can be registered.
Intuitive Operation New Advanced Functions
The main information is in one screen. The status of printer, the progress of ripping, the status of job can be checked at a glance. Nesting or composition of job are displayed visually.
The visual icons on the right side of the screen allows for the easy and quick setting of the print condition.
・Batch printing“Test the best profile when trying to print on
media which has never been used before”
・3-layer printingSimultaneous 3-layer printing(Color → White → Color)
・Convenient functionsEstimated Completion Time displayEnhanced layout functionPrinter Status display
The web update is available as well as RasterLinkPro5 which has been well received.The program update and the profile download can be done through the web easily
Web Update function
Mimaki Europe B.V.Sign Graphics Products
Easy creation of P&C data
• P&C data can easily be created with RasterLinkTools (Illustrator Plug-in)• RasterLink6 recognizes spot color path as cut line• Crop marks can be attached in RasterLink6
• P&C data creation with RasterLinkTools
47
①Select images ③Extracts frames of images
and specifies frames as spot color “CutContour”
②Click “Frame Extraction”
Mimaki Europe B.V.Sign Graphics Products
Input Profile
• Input profile “WideMimakiNaturalVivid” is available for reproducing brilliant color for Orange and Light Black ink set.
48
WideMimakiCMYK WideMimakiNaturalVivid WideMImaki2013forSign
・Mimaki’s standard input profile
・Available from(C)JV300/150 Series
・Reproduces brilliant colorand natural skin tone for(C)JV300/150 (Or,Lk)
・Available from JV400LXSeries
・High intensity input profile specialized for JV400LX(Or,G)
Mimaki Europe B.V.Sign Graphics Products
Options
• MBIS3 – Mimaki bulk ink system• OPT-J0364 for CJV150 series
• Eco-cartridge needed for BS3 inks• OPT-J0361, 1 set of 4 eco-cartridges, order 2 sets
• Anti-static sheet • OPT-J0374 for CJV150-75
• OPT-J0373 for CJV150-107
49
Mimaki Europe B.V.Sign Graphics Products
Options
• Drying Fan
• OPT-J0369 for CJV150-75
• OPT-J0368 for CJV150-107
• Air exhaust unit
• When ordering the Air exhaust unit, also the Drying fan needs to be ordered!
• OPT-J0372 for CJV150-75
• OPT-J0371 for CJV150-107
50
Mimaki Europe B.V.Sign Graphics Products
Specifications
51
CJV150-75 CJV150-107
Print head On-demand piezo printhead
Resolution 360 dpi,540 dpi,720 dpi, 1080 dpi, 1440 dpi
Drop size Min. 4pl, Max.35pl
Head height 2.0mm/2.5mm/3.0mm *manual adjustment(+1.0mm or +2.0mm)
Ink type Eco solvent ink:SS21/BS3/ES3(to be available separately) Sublimation Ink:Sb53
Ink color SS21: (CMYKLcLmLkOrWSi), BS3(CMYK) SS21: (CMYKLcLmLkOrWSi), BS3(CMYK), Sb53(BlMYKDKLBlLm)
Ink capacity SS21: 440ml cartridge/2L ink pack(W&Si: 220ml cartridge only)BS3: 600ml ink pack/ 2L ink pack
SS21: 440ml cartridge/2L ink pack(W&Si: 220ml cartridge only)BS3: 600ml ink pack/ 2L ink packSb53: 440ml cartridge/2L ink pack
Max. printing width Max.800mm Max.1,090mm
Max. media width Max.810mm Max.1,100mm
Media thickness 1.0mm (0.039’”) or less
Roll weight 40kg (88lb) or less
Cutting presure 10~450gf
Cut speed Speed:Max30cm/s Acceleration: Max 1G
Outside dimension 1,965mm(W)x700mm(D)x1,392mm(H) 2,255mm(W)x700mm(D)x1,392mm(H)
Packing size 2,250mm(W)x750mm(D)x1,050mm(H) 2,662mm(W)x750mm(D)x1,050mm(H)
Body weight 126kg 142kg
Power supply Single phase (AC100~120V/220~240V ±10%) 50/60Hz +/- 1Hz
Power consumption 1x (100V) Max 1440W 1x (220V)Max 1920W
Applicable standards VCCI class A / FCC class A / UL60950-1ETL / CE Marking(EMC, Low Voltage and Machinery) CB report / RoHS / REACH・CCC(pending)・Energy Star / RCM
Mimaki Europe B.V.Sign Graphics Products
●Remarks1. Do not install on the weak surface floor.2. Make sure to use in a ventilated environment.
・Environmental temperature: 20℃-30℃・Quality assurance temperature: 20℃-25℃・Humidity: 35-65%Rh (no condensation)・Temperature gradient: ±10℃/h or less・Dust: Equivalent to office environment
3.Do not install on carpets, etc because those are easy to be charged, and it can effect the image quality.
4. Ink odor generates. Please use the machine in a well-ventilated environment.
5. Do not install in the place where using a photographfixer or the place with acid steam like acetic acid, hydrochloric acid.
Packing / Installation
52
Model Width Depth Height WeightManpower for
installationPer
Container
CJV150-75 2,250mm750mm 1,050mm
180kg4 people
20ft:12 units40ft:24 unitsCJV150-107 2,662mm 200kg
*Installation space for PC is required separately
Installation condition
Mimaki Europe B.V.Sign Graphics Products
FAQ, 1
53
# Questions Answers
1 What is the outdoor durability of SS21 Silver and ES3 Silver SS21:1 year S3:Six monthsHowever, if the outdoor durability of lamination is poor, the outdoor durability of SS21/ES3 becomes poor accordingly.
2 How is the media compatibility of SS21 silver? SS21 Silver has poor media compatibility on monomeric-calendered PVC. Monomeric plasticizer has a relatively low tolerance for solvent and heat, which leads to the fast absorption of ink. Since SS21's silver requires time for its color material to align flat, the media compatibility with fast ink absorbing monomeric-calendered PVC is poor.
3 Can SS21 Silver be used for heat transfer media? It is not recommended for its poor scratch resistance.
4 What is the shelf life of SS21 Silver? 1 year from its production.
5 Can roll media in which outer diameter is more than 250mm be used if its weight is less than 40kg?
No, it cannot. Because the media interferes the bar under the media.
6 Can the media width of transparent media be detected automatically?
Yes, it can. When using black media, there may be occasion that media width cannot be detected automatically because the color of heater is also black.
7 When is the ink circulation of SS21 silver performed? Once every 4 hours for 2 minutes.
8 Is crop mark is used for pull-back printing? No, its not. There is no setting to set crop mark on RL6. After printing silver plate, the media is automatically pulled back to the origin, then, color plate is printed.
9 Are the cutting accuracy and the throughput of CJV300 and CJV150 equivalent?
Yes, they are.
Mimaki Europe B.V.Sign Graphics Products
FAQ, 2
54
# Questions Answers
10 Are the cutting accuracy and the throughput of CJV300/150 and CJV30 equivalent?
Cutting accuracy: Equivalent or betterThroughput: Depends on cutting data (Detailed info is prepared separately.)
11 How to print Mimaki Metallic Color Collection? Three types of Metallic Color Collections are stored in a folder of RL6.Please open the file from the folder and print as usual.
12 When printing metallic color, different media profiles can be used for silver plate and color plate, if the resolution and pass count are the same. (This was not possible before.)Is this also the same when using white ink?
Yes, it is. When composing color plate and white plate, different media profiles can be used for each, so please select the same profile for both color plate and white plate.
13 From CJV300/150, media width is detected not by the position of the pinch rollers at the both sizes, but by the actual media width. Then, is it possible to cut media out of the pinch rollers at the both sizes?
Yes, it is.
14 The adjustment of CJV30's P&C positioning accuracy is difficult, while Roland has the simple adjustment method. How is the CJV300 and CJV150?
There is an special adjustment pattern which is similar to Roland's pattern to print through RL6.
15 Can the setting of P&C positioning accuracy be registered as "Favorite"?
No, it cannot.
16 Can the pinch roller which is positioned out of media be turned off automatically?
Yes, it can.
17 Should the Pen-line sponge be used when preforming halfcut?
Half cut can be performed by using Pen-line rubber. However, to prevent the blade from abrasion, the use of Pen-line sponge(Optional) is recommended.
Mimaki Europe B.V.Sign Graphics Products
# Questions Answers
18 Has the power source of the Drying fan unit to be separated from the printer's?
Yes, it has to be. Power supply of less than 1.4A is required. (No restriction on voltage)
19 Is the power source required for the Air exhaust unit separately from the printer or the Drying fan unit?
No, it doesn’t. Because, the Air exhaust unit draws power from the Drying fan.In order to use the Air exhaust unit, the Drying fan unit has to be installed at the same time.
20 What is the precaution when using external heater? Please use a Relay Box to make it work in conjunction with the printer's state.
FAQ, 3
55
Mimaki Europe B.V.Sign Graphics Products
Revision History
56
Version Date Content Drafter
1.1 18-11-2004 Final release Johan Spies
Do not disclose this page
top related