mp r 3(final)
Post on 10-Apr-2017
289 Views
Preview:
TRANSCRIPT
DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING JOGINPALLY B. R. ENGINEERING COLLEGE
2014-2015
Seminar On
SIGN LANGUAGE RECOGNITION FOR DEAF AND DUMB PEOPLE
Bachelor of Technology In
Electronics & Communication Engineering Under the esteemed guidance of
Prof. V.SriRam B.E, M.tech
Presented byA.Vasavi (11J21A0407)B. Sushma Rani (11J21A0411)M. Ramya (11J21A0457)
CONTENT
1. Introduction2. Block diagram3. Individual block description4. Results5. Advantages & Disadvantages6. Applications7. Conclusions & Future scope8. References
INTRODUCTION
1.1. Aim:Deaf and dumb people use sign language for their communication but it
was difficult to understand by the normal people. The aim of this project is to reduce the barrier between them.
Sign language recognition system works on an algorithm for recognition of hand gestures with accuracy. Depending on the hand motions the output will be displayed on the LCD and also played through the speaker.
Block Diagram Of Sign Language Recognition For Deaf And Dumb People
INDIVIDUAL BLOCKS
The block diagram mainly consists of1) Power supply:
It activates all the electronic equipments in the digital circuits required
INDIVIDUAL BLOCKS
2) Microcontroller:It is a chip through which we can connect many other devices and also
those are controlled by the program which burn into the chip.• 8KB on-chip program memory. • 128 bytes on-chip data memory.• 4 register banks.• 32 bidirectional I/O lines organized as four 8 bit ports.• Two multi mode 16 bit Timer/Counters.• 8 interrupts.
AT89S52
INDIVIDUAL BLOCKS
3) LCD (LIQUID CRYTAL DISPLAY)A LCD is a flat panel display, electronic visual display or video display
that uses the light modulate. We are using 16×2 LCD display for our project.
16×2 LCD DISPLAY
INDIVIDUAL BLOCKS
4) Flex sensorsFlex sensors are sensors that change in resistance depending on the
amount of bend on the sensor. They convert the change in bend to electrical resistance-the more the bend, the more the resistance value. They are usually in the form of a thin strip that vary in resistance.
INDIVIDUAL BLOCKS
5) ADC (Analog to Digital converter) An analog-to-digital converter (ADC) is a device that converts a
continuous physical quantity to a digital number that represents the quantity's amplitude. The MCP3208 is a 12bit, 8 channel, Serial Peripheral Interface (SPI) Analogue to Digital Converter. It comes as an 16 pin DIP.
INDIVIDUAL BLOCKS
6) MAX232 The MAX232 is an integrated circuit that converts signals from an RS-
232 serial port to signals suitable for use in TTL compatible digital logic circuits. The MAX232 is a dual driver/receiver and typically converts the RX, TX, CTS and RTS signals.
It has 16 pins Operates Up To 120 kbit/s Low Supply Current . . . 8 mA Operates From a Single 5-V Power Supply
INDIVIDUAL BLOCKS
7) Voice processor:Voice processor is used to record audio and playback. We are using
APR33A3 IC.
INDIVIDUAL BLOCKS
8) Speakers :Speakers are one of the most common output devices used with computer
systems. Speakers are transducers that convert electromagnetic waves into sound waves.
INDIVIDUAL BLOCKS
9) Zigbee moduleZigBee is a technology of data transfer in wireless networks. It has low
energy consumption and is designed for multi-channel control systems, alarm systems, and lighting control. ZigBee is more economical than Wi-Fi while Bluetooth protocol also consumes more energy and has a greater scattering of parameters of conventionally compatible units. This is caused by the fact that Bluetooth does not have a unified data transfer standard. Still that does not mean that ZigBee is oriented towards autonomous use.
RESULTS
Transmitter Section of sign language recognition system kit when power supply is OFF
RESULTS
Receiver Section of sign language recognition system kit when power supply is OFF
RESULTS
Transmitter Section of sign language recognition system kit when power supply is ON
RESULTS
Receiver section of sign language recognition system kit when power supply is ON
RESULTS
Initial LCD Display of transmitter section of sign language recognition system kit
RESULTS
Initial LCD display of receiver section of sign language recognition system kit
RESULTS
Displaying Alphabet A
RESULTS
Displaying Alphabet B
RESULTS
Displaying Alphabet C
RESULTS
Displaying Alphabet D
RESULTS
Displaying Alphabet E
RESULTS
Displaying Alphabet F
RESULTS
Displaying Alphabet G
RESULTS
Displaying Alphabet H
ADVANTAGES AND DISADVANTAGES
a) Advantages: Eliminates the need of interpreter. Easy to incorporate and execute in any supporting operating system.
b) Disadvantages: System is trained on a limited database. Possibility of misinterpretation for closely related gestures.
APPLICATIONS
Web conferences Domestic applications Wearable computers
CONCLUSIONS & FUTURE SCOPE
• Conclusions:Thus we can conclude that sign language recognition for deaf and dumb
people helps to communicate easily between normal people and deaf and dumb people.
• Future scope:Sign language recognition system can be implemented in many
application areas examples include accessing government websites whereby no video clip for deaf and dumb is available or filling out forms online whereby no interpreter may be present to help.
top related