heavygaugem · pdf fileheavygaugemetaltometalscrews heavygaugemetaltometalscrews ... sheet...

For attaching gypsum board to 25-20 gaugesteel studs. Bugle head No. 2 ReducedPhillips Recess.

Bugle Fine

Part No. Size Box Qty

FS100 6 x 1 10M

FS118 6 x 1-1/8 10M

FS114 6 x 1-1/4 8M

FS112 6 x 1-1/2 6M

FS158 6 x 1-5/8 5M

FS6200 6 x 2 3.5M

FS200 7 x 2 3.5M

FS214 7 x 2-1/4 3M

FS212 8 x 2-1/2 2.5M

FS300 8 x 3 2M

FS312 10 x 3-1/2 1M

FS334 10 x 3-3/4 1M

FS400 10 x 4 1M

FS412 10 x 4-1/2 1M

FS500 10 x 5 1M

FS600 10 x 6 1M

Gypsum

Light GaugeSteel Stud

Bugle Fine Gypsum Board to25-20 Gauge Steel Studs

For attaching drywall to light gauge steel studs andfor special applications requiring strip-outresistance. No. 2 Reduced Phillips Recess.

High and Low Thread Drywall toLight Gauge Steel Studs

High and Low Thread

HL1 6 x 1 10M

HL118 6 x 1-1/8 10M

HL114 6 x 1-1/4 8M

HL158 6 x 1-5/8 5M

HL2 7 x 2 3.5M

HL214 7 x 2-1/4 3M

HL212 8 x 2-1/2 2.5M

HL3 8 x 3 2M

For attaching wood trim and base overgypsum board to light gauge steel studs orwood substrate. No.1 or 2 Square Recess.

Gypsum

Wood Trim

Trim Head Wood Trim & Base OverGypsum Board toLight Gauge Steel Studs

Trim Head

TH158 6 x 1- 5/8 5M

TH214 6 x 2- 1/4 3M

TH3 8 x 3 2M

For attaching gypsum board to .No. 2 Phillips Recess.

gypsum board

Drywall Laminator Gypsum Board to Gypsum Board

Drywall Laminator

LS10112 10 x 1-1/2 5M

Drywall Screws Self-Drilling Screws Self-DrillingSteelFramingScrewsLight Gauge Steel Screws

For attaching metal lath in stucco and otherapplications to wood or 25-20 gauge steelstuds. No. 2 Reduced Phillips Recess.

Metal Lathin Stucco

Modified Truss Metal Lath in Stucco to Woodor Light Gauge Steel Studs

Modified Truss

MT812 8 x 1/2 10M

MT834 8 x 3/4 8M

MT100 8 x 1 5M

MT114 8 x 1-1/4 5M

MT158 8 x 1-5/8 5M

MT178 8 x 1-7/8 4M

MT200 8 x 2 2.5M

MT212 8 x 2-1/2 2M

MT300 8 x 3 1.5M

Self-piercing needle point penetrates sheet metalfrom 0.0209 to 0.0358. Twin lead threads assurefast action and reduce driving torque and strip-out problems. Zinc plated.

Sheet Metal

Steel Stud

Slotted Hex Washer Head Penetrates Sheet Metal

Slotted Hex Washer Head

1/4” Drive

5/16” Drive

HW4712 7 x 1/2 15M

HW4812 8 x 1/2 10M

HW4834 8 x 3/4 10M

HW48100 8 x 1 8M

HW48112 8 x 1-1/2 5M

HW48200 8 x 2 3M

HW41012 10 x 1/2 8M

HW41034 10 x 3/4 6M

HW410100 10 x 1 5M

HW410112 10 x 1-1/2 3M

HW410200 10 x 2 2M

HW51012 10 x 1/2 8M

HW51034 10 x 3/4 6M

HW510100 10 x 1 5M

HW510112 10 x 1-1/2 3M

HW510200 10 x 2 2M

For attaching wood trim over gypsum to 20-14gauge metal. No. 1 or 2 Square Recess. Availablein zinc and black phosphate.

Wood Trim

Gypsum Board

Trim Head Wood Trim Over Gypsumto 20-14 Gauge Metal

Trim Head

THDZ158 6 x 1-5/8 5M

THDZ214 6 x 2-1/4 3M

THDZ3 8 x 3 2M

THD158* 6 x 1-5/8 5M

THD214* 6 x 2-1/4 3M

THD3* 8 x 3 2M

*Black Phosphate

For attaching 5/8” - 3/4” plywood to 18-12 gaugemetal. No. 2Reduced Phillips Recess.

Wings eliminate pre-drilling of wood.

Phillips Wafer Head With Wings 5/8”-3/4” Plywoodto 18-12 Gauge Metal

Phillips Wafer Head With Wings

PWD101716 10 x 1-7/16 3M

For attaching 20-16 gauge steel track to 20-16gauge steel studs. With serrations to reduce spinout. No. 2 Reduced Phillips Recess. Available inzinc and black phosphate.

Steel Track

Steel Stud

Pan Framer 20-16 Gauge SteelTrack to 20-16 Gauge Steel Studs

Pan Framer

PFD716 7 x 7/16 10M

PFD71615 7 x 7/16 15M

PFZD71615M 7 x 7/16 15M

*Black Phosphate **Zinc

For attaching 20-14 gauge steel track to 20-16gauge steel studs. No. 2 Reduced Phillips Recess.

Steel Track

Steel Stud

Pancake Framer 20-14 Gauge SteelTrack to 20-16 Gauge Steel Studs

Pancake Framer

PPH1058 10 x 5/8 7.5M

For attaching metal lath in stucco and otherapplications to 20-16 gauge steel studs.No. 2 Reduced Phillips Recess.

Metal Lathin Stucco

Steel Stud

Modified Truss Metal Lath in Stuccoto 20-16 Gauge Steel Studs

Modified Truss

MTD812 8 x 1/2 10M

MTD834 8 x 3/4 10M

MTD8100 8 x 1 8M

MTD8114 8 x 1-1/4 6M

MTD8158 8 x 1-5/8 5M

MTD8178 8 x 1-7/8 3M

MTD8200 8 x 2 2.5M

MTD8212 8 x 2-1/2 2M

MTD8300 8 x 3 1.5M

MTD1034 10 x 3/4 5M

Low profile 20-16 gauge framer. No. 10 diameterfor added shear strength. With serrations to reducespin out. No. 2 Reduced Phillips Recess.

Steel Track

Steel Stud

Low Profile Truss Low Profile 20-16 Gauge Framer

Low Profile Truss

FT1012 10 x 1/2 8.5M

FT1034 10 x 3/4 7.5M

AnItochuCompany

For attaching gypsum board to wood studs.Bugle head No. 2 Reduced Phillips Recess.

Gypsum

Wood Stud

Bugle Coarse

CS100 6 x 1 10M

CS118 6 x 1-1/8 10M

CS114 6 x 1-1/4 8M

CS112 6 x 1-1/2 6M

CS158 6 x 1-5/8 5M

CS6200 6 x 2 3.5M

CS200 7 x 2 3.5M

CS214 7 x 2-1/4 3M

CS212 8 x 2-1/2 2.5M

CS300 8 x 3 2M

CS312 10 x 3-1/2 1M

CS334 10 x 3-3/4 1M

CS400 10 x 4 1M

CS412 10 x 4-1/2 1M

CS500 10 x 5 1M

CS600 10 x 6 1M

Bugle Coarse Gypsum Board to Wood Studs

For attaching gypsum board to 20-14 gauge steelstuds. No. 2 Reduced Phillips Recess. Availablein zinc and black phosphate.

Gypsum Board

Steel Stud

Bugle Head Gypsum Board to20-14 Gauge Steel Studs

Bugle Head

SDZ100 6 x 1 10M

SDZ118 6 x 1-1/8 10M

SDZ114 6 x 1-1/4 8M

SDZ158 6 x 1-5/8 5M

SDZ178 6 x 1-7/8 4M

SDZ238 8 x 2-3/8 3M

SDZ258 8 x 2-5/8 2M

SDZ300 8 x 3 2M

SD100* 6 x 1 10M

SD118* 6 x 1-1/8 10M

SD114* 6 x 1-1/4 8M

SD158* 6 x 1-5/8 5M

SD178* 6 x 1-7/8 4M

SD238* 8 x 2-3/8 3M

SD258* 8 x 2-5/8 2M

SD300* 8 x 3 2M

*Black Phosphate

For attaching up to 3/4” plywood to 20-14 gaugemetal. Combo drive. 1,000 hour exterior allweather coating.

Bugle Head Pilot Point Plywood to20-14 Gauge Steel Metal

Pilot Point Bugle Head

PP2 8 x 2 4M

For attaching up to 1-1/8” plywood to 18-12gauge metal. Combo drive. 1,000 hour exterior allweather coating.

Pilot Point Flat Head

PP212 10 x 2-1/2 2M

For attaching 7/8” - 2-1/4” plywood to 16-12gauge metal. No. 3 point.

No. 2 or 3 Phillips Recess.Wings eliminate pre-

drilling of wood.

Phillips Flat Head With Wings 7/8”-2-1/4” Plywoodto 16-12 Gauge Metal

Phillips Flat Head with Wings

PF10158 10 x 1-5/8 3M

PF12200 12 x 2 2M

PF12212 12 x 2-1/2 1M

PF14234 14 x 2-3/4 1M

PF14314 14 x 3-1/4 1M

HeavyGaugeMetal ToMetal ScrewsHeavyGaugeMetal ToMetal Screws

For penetrating multiple layers of light steel –extra high hex for added strength. With serrationsto reduce spin out.

Layers ofSheet Metal

Steel Stud

High-Hex Washer Head Penetrate Multiple LayersWith #3 Drilling Point of Light Gauge Steel

High-Hex Washer Head With Serrations

HH1034 10 x 3/4 6.5M

Heavy gauge metal fastening, sheet metal panelsor clips to steel up to 3/8” thick. 1,000 hourexterior all weather coating.

Hex Washer Head With Heavy Gauge Sheet Metal Panels5/16” Drive #4 Drilling Point to Steel up to 3/8” Thick

Hex Washer Head - 5/16” Drive #4 Drilling Point

X41278 12 x 7/8 4M

Fastening of overlapping heavy gauge metalpanels or sheets. Also available with neoprenebonded washer.

Stitch/LapWith5/16”Drive OverlappingHeavy#1DrillingPoint MetalPanelsorSheets

Stitch/Lap - 5/16” Drive #1 Drilling Point

LAP1478 14 x 7/8 3.5M

LAP1478S 14 x 7/8 3.5M(w/washer)

For attaching roofing panels and wall panels tosteel studs or purlins and over-lapping exteriorsheets.

HexWasherHeadWith Roofing&WallPanelsNeopreneBondedWasher, toSteelStudsorPurlins3/8”Drive#3DrillingPoint Hex Washer Head w/Neo - 3/8” Drive

HDW1434 14 x 3/4 4M

HDW14100 14 x 1 3M

HDW14114 14 x 1-1/4 2M

HDW14112 14 x 1-1/2 2M

HDW14200 14 x 2 1M

HDW14212 14 x 2-1/2 1M

HDW14300 14 x 3 1M

Metal to metal fastening used in sheet metal andlight steel framing. Very common in HVAC ductwork assembly.

HexWasherHeadWith Metal toMetaland1/4”Drive#2DrillingPoint LightGaugeSteelFraming

Hex Washer Head - 1/4” Drive

HWD812 8 x 1/2 10M

HWD858 8 x 5/8 10M

HWD834 8 x 3/4 10M

HWD8100 8 x 1 8M

HWD8114 8 x 1-1/4 6M

HWD8112 8 x 1-1/2 4M

HWD8200 8 x 2 3M

Metal to metal fastening used in medium gaugemetal to metal framing. Commonly used by sheetmetal and HV C contractors and fabricatorsA

Sheet Metal

Steel Stud

Hex Washer Head With Medium Gauge Sheet Metal5/16” Drive #3 Drilling Point to Metal Framing

HWD1012 10 x 1/2 8M

HWD1058 10 x 5/8 7M

HWD1034 10 x 3/4 6M

HWD10100 10 x 1 5M

HWD10114 10 x 1-1/4 4M

HWD10112 10 x 1-1/2 3M

HWD10200 10 x 2 2M

Metal to metal fastening for heavy gauge metalattachment. Up to 3/8” thickness

HexWasherHeadWith Metal toMetalHeavyGauge3/8”Drive#3DrillingPoint up to3/8”Thickness

HWD14034 14 x 3/4 4M

HWD14100 14 x 1 3M

HWD14114 14 x 1-1/4 2M

HWD14112 14 x 1-1/2 2M

HWD14200 14 x 2 1M

HWD14212 14 x 2-1/2 1M

HWD14300 14 x 3 1M

HWD14400 14 x 4 0.5M

HWD14500 14 x 5 0.5M

HWD14600 14 x 6 0.5M

CementBoardScrews

Designed to fasten cement board to wood or lightgauge steel studs (25-20 gauge). Nibs under thehead allow it to countersink into the board. Thespade point penetrates the board without crackingand high-low threads ensure high withdrawlresistance. No. 2 Reduced Phillips Recess withnibs. 1,000 hour exterior all weather coating.

Cement Board

Wood Stud

Spade-Point With Nibs Cement Board to Woodor Light Gauge Steel Studs

Spade-Point Cement Board Screws

CB114 8 x 1-1/4 5M

CB158 8 x 1-5/8 5M

CB214 8 x 2-1/4 3M

Designed to fasten cement board to metal studs(20-14 gauge). Nibs under the head allow it tocountersink into the board. No. 2 ReducedPhillips Recess with nibs. 1,000 hour exterior allweather coating.

Cement Board

Steel Stud

Self-Drilling With Nibs Cement Boardto Steel Studs

Self-Drilling Cement Board Screws

CBD114 8 x 1-1/4 5M

CBD158 8 x 1-5/8 5M

ConcreteScrewAnchors

A re-usable screw with high holding power.For use in light duty anchoring, door andwindow frames, thresholds, plumbing strapsand electrical conduits. Taps it’s own threadin concrete, brick and other masonryproducts. Drill the starter hole, drive thescrew and procedure is complete.

Wood Framing

Concrete

Hex Washer Head Slotted Light Duty Anchoringto Concrete, Brick and OtherMasonry Products

Flat Head Phillips

1/4” Hex Head

HC3114 3/16 x 1-1/4 6M

HC3214 3/16 x 2-1/4 3M

HC3314 3/16 x 3-1/4 2M

HC3400 3/16 x 4 1M

HC3134 3/16 x 1-3/4 4M

HC3234 3/16 x 2-3/4 3M

HC3334 3/16 x 3-3/4 1.5M

#2 Phillips Flat Head

FC3114 3/16 x 1-1/4 6M

FC3214 3/16 x 2-1/4 3M

FC3314 3/16 x 3-1/4 2M

FC3400 3/16 x 4 1M

FC3134 3/16 x 1-3/4 4M

FC3234 3/16 x 2-3/4 3M

FC3334 3/16 x 3-3/4 1.5M

#3 Phillips Flat Head

FC4114 1/4 x 1-1/4 3M

FC4214 1/4 x 2-1/4 2M

FC4314 1/4 x 3-1/4 1M

FC4134 1/4 x 1-3/4 2M

FC4234 1/4 x 2-3/4 2M

FC4400 1/4 x 4 1M

5/16” Hex Head

HC4114 1/4 x 1-1/4 3M

HC4214 1/4 x 2-1/4 2M

HC4314 1/4 x 3-1/4 1M

HC4134 1/4 x 1-3/4 2M

HC4234 1/4 x 2-3/4 2M

HC4400 1/4 x 4 1M

FiberCementBoardScrewsFor Wood Lap Siding,

Fiber Cement Board to Wood

Fiber Cement Board Screws for Wood

FCBS114 8 x 1-1/4 8M

FCBS158 8 x 1-5/8 5M

Designed to fasten fiber cement board in areasrequiring high wind shear and pull-throughresistance. Recommended for: Lap siding, fibercement board to steel studs, fiber cement roofingtrim, flooring for tile in kitchen and bath. Type 17point. No. 2 Reduced Phillips Recess wafer headwith nibs. 1,000 hour exterior all weather coating.

ForWood FiberCementBoard toWood forAreas inHighWind

Fiber Cement Board Screws for Wood

FCBSS114 8 x 1-1/4 8M

FCBSS158 8 x 1-5/8 5M

Designed to fasten fiber cement board to steelstuds (0.100” max). Wings allow cutter head tocountersink flush with fiber cement board.No. 2 Reduced Phillips Recess flat head with nibs.1,000 hour exterior all weather coating.

ForSteel FiberCementBoardtoSteelStuds

Fiber Cement Board Screws for Steel

FCBD114 8 x 1-1/4 5M

FCBD158 8 x 1-5/8 5M

FCBD214 8 x 2-1/4 2.5M

Designed to fasten fiber cement board in areasrequiring high wind shear and pull-through resistance(0.100” max. steel stud). Recommended for: Lapsiding, fiber cement board to steel studs, fiber cementroofing trim, flooring for tile in kitchen and bath.No. 2 Reduced Phillips Recess wafer head with nibs.1,000 hour exterior all weather coating.

ForSteel FiberCementBoard toSteelStuds forAreas inHighWind

Fiber Cement Board Screws for Steel

FCBDS114 8 x 1-1/4 5M

FCBDS158 8 x 1-5/8 5M

FCBDS214 8 x 2-1/4 3M

Acoustical EyeLagScrews

Eye Lag Screws- Sharp Point Hang Ceiling Gridinto Wood Joists

Eye Lag Screws - Sharp

EL3 1/4 x 3 1M

EL4 1/4 x 4 1M

EL5 1/4 x 5 1M

Primarily used for hangingsuspended ceiling grid intowood joists.

Wood Joist

Eye Lag Screws- Self Drilling Hang Ceiling Gridinto Metal Joist

Primarily used for hangingsuspended ceiling grid intometal studs.

Metal Joist

Eye Lag Screws - Self Drilling

ELDZ2 1/4 x 2 1M

ELDZ3 1/4 x 3 1M

WoodWorkingScrews

Use for attaching cabinets to wood or light gauge(25-20 gauge) steel studs. Combo drive allowsfastener to remain on bit while cabinet is held inplace for attachment. Type 17 point. Yellow zinc.

Cabinet

Cabinet Screws Cabinets to Woodor Light Gauge Studs

Cabinet Screws, Yellow Zinc

CBS238 8 x 2-3/8 2.5M

CBS300 8 x 3 2M

Use for attaching wood to wood. Recommendedfor cabinet and general wood-working where thegold/yellow head meets user’s cosmeticrequirements, an interior fastener notrecommended for outdoor decking. Bugle headNo. 2 Reduced Phillips Recess. Yellow zinc.

Coarse Screws Wood to Wood Cabinetand General Wood Working

Coarse Screws, Yellow Zinc

GS114 6 x 1-1/4 8M

GS112 6 x 1-1/2 6M

GS158 6 x 1-5/8 5M

GS200 7 x 2 3.5M

GS214 7 x 2-1/4 3M

GS212 8 x 2-1/2 2.5M

GS300 8 x 3 2M

GS312 10 x 3-1/2 1M

GS334 10 x 3-3/4 1M

GS400 10 x 4 1M

WoodWorkingScrews

An all around wood to wood product screw forbuilding cabinets, furniture, etc...where smoothcounter-sinking via the nibbed head and the anti-splitting action of the type 17 point are needed.Can also be used to attach wood to woodproducts to light gauge steel (25-20 gauge).

. Combo Drive with nibs. Zinc plated.Type

17 point

Particle Board

Particle Board Screws Wood to Wood All AroundCabinet and Furniture Screw

Particle Board Screws, Combo Drive

PBP08114 8 x 1-1/4 6M

PBP08112 8 x 1-1/2 5M

PBP08158 8 x 1-5/8 5M

PBP08200 8 x 2 3M

PBP08212 8 x 2-1/2 2.5M

PBP08300 8 x 3 2M

Also called “Face Frame Screws”. Used in hardwoodcabinet and furniture making. Type 17 point.Pan head Combo Drive. Black phosphate.

Hardwood

Hardwood Screws Hardwood Cabinet &Furniture Making

Hardwood Screws, Combo Drive

PHC6114 6 x 1-1/4 6M

PHC6112 6 x 1-1/2 6M

1-800-676-6777

www.primesourcebp.com

Plywood

Phillips Wafer Head

PWD1034 10 x 3/4 8M

PWD10100 10 x 1 5M

PWD10114 10 x 1-1-/4 4M

PWD10112 10 x 1-1/2 4M

For attaching 25-20 gauge steel track to25-20 gauge studs. With serrations toreduce spin out. No. 2 Reduced PhillipsRecess.

Light GaugeSteel Track

Pan Framer

PF716 7 x 7/16 10M

PF71615M 7 x 7/16 15M

Pan Framer Light Gauge Steel Track toLight Gauge Steel Studs

For attaching sNo. 2 Reduced Phillips Recess.

trapping or furring channel to steeljoist.

Furring

Steel Joist

Phillips Pan Head Strapping or FurringChannel to Steel Joist

Phillips Pan Head

PD812 8 x 1/2 10M

PD834 8 x 3/4 10M

PD8100 8 x 1 8M

PD8114 8 x 1-1/4 4M

PD1012 10 x 1/2 8M

PD1058 10 x 5/8 7M

PD1034 10 x 3/4 6M

PD10100 10 x 1 5M

Metal to metal fastening used in sheet metal toattach purlins and channels to structural studs.Commonly used in up to 5 gauge steel.

HexWasherHeadWith Metal toMetal,Purlins&Channels5/16”Drive#3DrillingPoint toStructuralStuds

HWD12034 12 x 3/4 5M

HWD12100 12 x 1 3M

HWD12114 12 x 1-1/4 3M

HWD12112 12 x 1-1/2 3M

HWD12200 12 x 2 2M

HWD12212 12 x 2-1/2 1M

HWD12300 12 x 3 1M

1 2 3 4 5 PROREF06/03

Designed to fasten fiber cement board to wood.Recommended for: Lap siding, fiber cement boardto wood, fiber cement roofing trim, flooring for tilein kitchen and bath.No. 2 Reduced Phillips Recess flat head with nibs.1,000 hour exterior all weather coating.

Type 17 point.

FiberCement Board

For attaching 1/4”-1/2” plywood to 18-12 gaugemetal. No. 2 Reduced Phillips Recess.

Phillips Wafer Head 1/4”-1/2” Plywood to18-12 Gauge Metal

Flat Head Pilot Point Plywood to18-12 Gauge Steel Metal

Sheet Metal

Hex Washer Head With Heavy Gauge Metal Fastening5/16” Drive #5 Drilling Point Sheet Metal to Steel

Hex Washer Head - 5/16” Drive #5 Drilling Point

X512114 12 x 1-1/4 2M

X512112 12 x 1-1/2 2M

X512200 12 x 2 2M

Heavy gauge metal fastening, sheet metalpanels or clips to steel up to 1/2” thick.1,000 hour exterior all weather coating.

For use in metal building applications wheremoisture needs to be sealed out by using aneoprene bonded washer.

Sheet Metal

Steel Stud

HexWasherHeadWithNeopreneBondedWasher,5/16”Drive#3DrillingPoint

Roofing&WallPanels toSteelStuds

Hex Washer Head w/Neo - 5/16” Drive

HDW1034 10 x 3/4 6M

HDW10100 10 x 1 5M

HDW10114 10 x 1-1/4 4M

HDW10112 10 x 1-1/2 3M

HDW10200 10 x 2 2M

HDW1234 12 x 3/4 5M

HDW12100 12 x 1 3M

HDW12114 12 x 1-1/4 3M

HDW12112 12 x 1-1/2 3M

HDW12200 12 x 2 2M

heavygaugem · pdf fileheavygaugemetaltometalscrews heavygaugemetaltometalscrews ... sheet...

Documents

box-loc metal stud bracketed boxes · box-loc metal stud...

steel stud & track - potter interior...

headed steel stud anchorsheaded steel stud anchors … ·...

metal stud partition presentation

shear stud cap in steel decks

wall systems for steel stud/masonry · pdf file2...

builders steel stud guide

stud wall & drywall - tnb.ca - thomas & betts · pdf...

w36.bg knauf metal stud partitions

headed steel stud anchors headed steel stud anchors - ideals

light duty pipe/steel stud rack - skyjack

steel stud catalog

steel stud & track - usg

headed steel stud anchorsheaded steel stud anchors in

metal structures lecture xiii steel trusses -...

steel stud systems

brick veneer steel stud wall

steel stud boxes - ideadigitalcontent.com

light duty pipe/steel stud rack

knauf metal stud partitions - internet archive