expression of interest for pre … fda 16.03.17.pdf · · 2017-03-16site, installation, testing...
Post on 22-May-2018
217 Views
Preview:
TRANSCRIPT
Page 1 of 13
EXPRESSION OF INTEREST
FOR
PRE-QUALIFICATION OF VENDORS FOR THE
DESIGNING, ENGINEERING, SUPPLY, LAYOUT
AT SITE, INSTALLATION, TESTING AND
COMMISSIONING OF ONLINE UPS 60 KVA x 3
NO. INCLUDING ANCILLARY SERVICES, ON
TURNKEY BASIS FOR FOOD & DRUG
LABORATORY OF FDA, PUNJAB AT KHARAR
Office: SCO: 7-8, Phase-V, S.A.S. Nagar, (Mohali) - 160059
Phone: 0172 – 5020896, 5020892, Tele Fax: 0172 – 5020895
Website: pbtilabs.com, E-mail:pbti2005@yahoo.com, mahajanrajiv@pbtilabs.com
Page 2 of 13
EXPRESSION OF INTEREST (EOI) FOR THE PRE-QUALIFICATION OF VENDORS
FOR THE DESIGNING, ENGINEERING, SUPPLY, LAYOUT AT SITE,
INSTALLATION, TESTING AND COMMISSIONING OF ONLINE UPS 60 KVA x 3 NO.
INCLUDING ANCILLARY SERVICES, ON TURNKEY BASIS FOR FOOD & DRUG
LABORATORY OF FDA, PUNJAB AT KHARAR
Sealed EOI in the prescribed form is hereby invited from the manufacturers / authorized
distributors / dealers, duly authorized to quote for this particular tender, on behalf of the Food
and Drug Administration (FDA), Punjab for the work of Designing, Engineering, supply, layout at
site, installation, testing and commissioning of online UPS System (Emerson-Libert/ Schneider-
APC/ Eaton/ Mitsubishi/Gutor make) including Ancillary services on TURN KEY basis, at Food &
Drug Testing Laboratories of FDA, Punjab, Kharar, SAS Nagar (Mohali), through its Project
Management Consultant, Punjab Biotechnology Incubator (PBTI), Mohali
1. BRIEF SCOPE & DESCRIPTION OF CONTRACT:
A. BRIEF SCOPE:
The Agency will be required to undertake Designing, Engineering, supply, layout at site, installation, testing and commissioning of online UPS System, including Ancillary services on TURN KEY basis, for Food & Drug Testing Laboratories of FDA, Punjab at Kharar, SAS Nagar (Mohali).
Ancillary services include Distribution of UPS power supply and Earthing stations for specific Laboratories mentioned in the scope of work.
The job is required to be completed in 6 week’s time from the date of issuance
of purchase order.
B. Brief Description of the EOI process:
The EOI shall be submitted in single sealed envelope and super scribed as “EOI no. PBTI/FDA/16-17/EOI/01 for online UPS system” on or before 24.03.2017 at 10 AM and shall be opened on the same day at 10.30 AM.
The interested parties shall submit EOI documents as per the requirements mentioned in this document. Based on the proposals submitted tender document with detailed terms of reference shall be issued to eligible parties.
The EOI should be prepared and submitted as per the EOI formats only prescribed in the EOI document and should be addressed to: Chief Executive Officer, Punjab Biotechnology Incubator SCO 7 & 8, Phase -5, SAS Nagar (Mohali) - 160059.
Prospective parties are strongly advised to visit Food & Drug Testing Lab’s FDA,
Kharar, the installation site at the following address, prior to submission of EOI: Food & Drug Testing Laboratories
Food & Drug Administration, Punjab
Adjoining Civil Hospital, Kharar, Distt. SAS Nagar (Mohali)
Contact person: Sh. Pradeep Mattu – Joint Commissioner, FDA, Punjab
Page 3 of 13
2. EXPRESSION OF INTEREST SCHEDULE
1 EOI NO. PBTI/FDA/16-17/EOI/01
2 Name of Work Expression of Interest for the Pre-Qualification of Vendors for the Designing, Engineering, Supply, Layout At Site, Installation, Testing And Commissioning of Online UPS 60 KVA X 3 No. Including Ancillary Services on Turnkey basis for Food & Drug Laboratory of FDA, Punjab at Kharar
3 Validity of Proposal
Six months from the date of submission of final proposal
4 Estimated Cost Rs. 35 Lacs
5 Date of submission of EOI application 24.03.2017 at 10 AM
Page 4 of 13
3. SCOPE OF WORK
Overall Objective of this EOI is to engage manufacturer/Distributor/Dealer having
expertise and experience in the Designing, Engineering, supply, layout at site, installation,
testing and commissioning of online UPS System.
The scope of work broadly includes the Designing, Engineering, supply, layout at site, installation, testing and commissioning of:
1. UPS system 60 KVA X 3 as per technical specifications mentioned at Clause no. 5 of this document.
2. The UPS is to be installed in Room no. 409 at level 4 of FDA building, Kharar and distribution is to be done at Level 3 & 4.
3. Suitable Surge Protection units for each UPS
4. Control Switchgear and protection on incoming power supply
5. Control Switchgear and protection on ougoing UPS power supply
6. Suitable UPS power supply distribution panel for atleast 8 outgoings
7. Suitable VTPN Distribution Board in each duct (total 8 no.) at level 3 & level 4 of FDA building, Kharar.
8. Double Copper earthing for UPS system to be installed in UPS room at level 4.
9. Double Copper earthing for metallic frames of electrical installations.
10. 5 no. copper Earthing stations for Room no. 319,321 & 322 at level 3 and Room no.,417 & 419 at Level 4 of FDA building, Kharar.
11. Suitable size copper stranded conductor multi-core cable to be used for inter-connections, termination of cables with suitable size LBHD lugs/thimbles, proper glands etc.
12. Suitable size GI cable trays for laying of cables as required.
13. Any damage to the building while execution of the work is to be repaired to the original condition and proper cleaning of debris after completion of works.
The scope shall also include all such items which may not have been specifically mentioned but which, otherwise, are required to complete the job. The scope also includes free maintenance, repairs and replacement as may be required, throughout the defect liability period. While designing, the CPWD/PWD specifications must be followed.
Scope also includes the complete service of unloading, transportation, handling, storage, erection, final check-up, testing and commissioning services including all labour, supervision, erection tools, equipment and consumables as may be required to complete the job in its totality. Conducting all necessary tests after completion of erection at site to the full satisfaction of the Purchaser. The Contractor shall arrange all test gadgets and instruments necessary for conducting and demonstrating relevant tests at site. Training of Owner’s personnel for trouble-free operation and maintenance of installations before handing over the package to the Owner. Furnishing of various drawings, data, test reports and certificates, erection manual, operation manual, service and maintenance manual etc. as required for proper operation and maintenance by the Purchaser.
Page 5 of 13
4. Pre-Qualification requirements:
Sr.no. Eligibility Criteria Documents to be submitted
1 The Applicant Company should be a company registered in India under the Indian Companies Act of 1956
The registration no. of the firm /company along with Sales Tax no./Certificate of Incorporation. Photocopy of TAN, PAN, VAT No., Service Tax regd. No. etc. and Tax clearance certificates
2 The Applicant Company should be authorized distributor / authorized dealer of reputed UPS Manufacturers
Proof should be enclosed like certificate issued by UPS manufacturers (as per format at ANNEXURE – I)
3 The Applicant Company Should be in the business of UPS (20 KVA or above) for at least past 5 years and should have executed at least three (03) similar work of estimated cost (Rs.35 Lacs) for each of value not less than 40% of the estimated cost or two similar works each of value not less than 60% of the estimated cost or one similar work of value not less than 80% of the estimated cost or more during the last five (05) years ending last day of previous month (i.e. February, 2017)). (Similar work means: Supply, installation, testing and commissioning of UPS system with the capacity 20 KVA or above).
List with documentary evidence. Proof should be enclosed like order copy or installation certificate / satisfactory certificate etc. (preferably of Govt. Institutions/Organizations)
4 Annual Turnover in UPS business should be minimum Rs.5 Crores for the last three years. The company should be in profit during the last three years i.e. 2013-14, 2014-15 and 2015-2016 from UPS Business.
Audited Balance Sheet and P & L Account certified by Chartered Accountant for last 3 years.
5 Solvency Certificate for Rs. 5.00 crore Certificate issued by any Scheduled Bank during the last six months
6 The vendor should have Capability to attend the UPS complaints within 12 hours to 24 hours for this the vendor should have its Service Centres preferably in Tri-city of Mohali/ Chandigarh/ Punchkula
Proof should be enclosed along with the address and phone number.
Page 6 of 13
5. Technical Specifications of UPS:
Technical Specification of UPS System (3 phase Input & Output) in parallel
Capacity : 60 KVA
No. of Units Required : 03
UPS Technology : IGBT (for both the rectifier and inverter) based Microprocessor Controlled, double conversion with digital display.
Backup time at full load : 15 minutes on each UPS with individual battery bank
Input Rating (at Full load): Voltage Frequency Total Harmonic Distortion (THD) Input Power Factor
: : : :
350 to 470 V 50 Hz ± 10% < 5% 0.95 or better
Output Rating (at Full load): Voltage Frequency Total Harmonic Distortion (THD) Output Power Factor
: : : :
415V ± 1% 50 Hz ± 0.5 Hz <1 % on linear load and <5% on nonlinear load 0.9 or better
Overall efficiency (Double Conversion Mode) : >94%
Overload capacity : 125% for 10 minutes 150% for 1 minutes
Battery testing : Automatic
Battery Circuit breaker : MCCB of appropriate capacity with each UPS
Static Switch : Built-in maintenance Bypass and Static Bypass Switch with 100% rating
Parallel redundant : Provision upto 4 machines
Display : LCD with event history minimum 200 events
Acoustic noise at rated load (at 1 mtr) : <65 dB
Maximum permissible non linear load Surge Protection
: :
100% with 3:1 crest Factor for 60KVA UPS – Min. 100 KA
Environmental characteristics
: 0 - 40oC temp. without de-rating, 90% RH at 20oC.
Following protection shall be provided: a) Overload and short circuit at output of UPS b) Over & Under voltage at output c) Deep Discharge at battery terminals d) Over Temperature.
Monitoring for the following shall be provided: Voltage mains bypass & load with phase to phase & phase to neutral.
a. Current : On each phase for mains, bypass & load b. Load % on each Phase c. Battery current, voltage, remaining time and total load utilization.
Page 7 of 13
d. Load in KVA and KW on each phase e. Frequency
UPS should be suitable to supply output power and the charging current for the battery at
the same time.
Enclosure of UPS shall meet minimum IP 20 protection requirements
Detailed Circuit diagram along with service manual shall be provided in duplicate.
Minimum VAH rating of battery bank for 15
minutes backup
: Minumum 38000 VAH for 60 KVA each
Warranty:
UPS
SMF (Sealed Maintenance Free) Batteries
:
:
Three (03) Years
Two (02) Years
Comprehensive Maintenance Contract for UPS : After Expiry of Three (03) years
standard warrantee supplier has to
quote year wise rates for Four (04)
years Comprehensive Maintenance
Contract (CMC).
Make:
UPS
SMF Batteries
MCCB
Cables
:
:
:
:
Emerson-Libert/ Schneider- APC/
Eaton/ Mitsubishi/Gutor
Exide / Amaron(Quanta) / Rocket
ABB/Schneider/L&T/Legrand
Havells/Finolex/Polycab/RR
UPS should be provided with : SMF Batteries, Battery rack, Battery
interconnections complete in all
respect.
Page 8 of 13
6. General Conditions of Expression of Interest:
The Bidder shall bear all costs associated with the preparation and submission of its EOI and
PBTI, will in no case be responsible or liable for these costs, regardless of the conduct or
outcome of the bidding process.
A. Amendment of EOI
At any time prior to the dead line for submission of EOI, PBTI may, for any reason,
modify the EOI document by issuing an amendment.
There will not be any individual communication in respect of general notices,
amendments, etc. All notices/information will be disseminated through the PBTI's
website and it will be binding on the parties. The prospective parties are advised to
browse the website of the PBTI www.pbtilabs.com on a day-to-day basis till the EOI is
concluded.
B. Method of Submission of EOI
The interested eligible parties are required to apply for Pre-Qualification on the
company’s letter head, giving company’s Profile & experience, duly supported by the
requisite documents in sealed cover, super-scribed on top “Expression of Interest for
online UPS system” so as to reach PBTI’s office by 1000 Hrs on 24.03.2017 and shall be
addressed to;
Chief Executive Officer,
Punjab Biotechnology Incubator
SCO 7 & 8, Phase -5,
SAS Nagar (Mohali) -160059
PBTI will not accept any responsibility regarding non-receipt or delay in receipt of
documents sent through post. Documents sent by fax/e-mail will not be accepted.
The EOI submitted by the parties should include the following:
i. General Information as per format at Annexure –II
ii. Pre-qualification details as per format at Annexure –III
iii. Complete Layout drawings
iv. Bills of Quantities
v. Specifications of Items other than UPS
vi. The details of statutory requirements if any
vii. Testing proposed during commissioning
If the bids are not submitted as per the requirement of the above clauses, PBTI shall
assume no responsibility for the offer’s misplacement or premature opening and
consequential rejection.
The CEO, PBTI reserves the right to reject or accept any or all expression of interest received in response to this advertisement without assigning any reasons, whatsoever. PBTI is under no obligation to inform the contractors of the reason of the selection or rejection.
Page 9 of 13
The applicant’s representative may be present during the bid opening.
The pre-qualified vendors only will be invited through individual notice to participate in
the further tender procedure. The detailed tender document shall be issued to the pre-
qualified vendors for submission by the stipulated date.
C. Deadline for submission of EOI
EOIs must be received in the office of the PBTI at the above address at Mohali not later
than 24.03.2017 at 10 AM.
In the event of the specified date for submission of EOI being declared holiday, the EOI
shall be received up to the appointed time on the next working day.
If the EOI is sent by Registered post or by Courier, it should reach the above office on or
before the time and date stipulated for the receipt of EOI. PBTI shall not be held liable
for the delay in transit where the EOI is sent by post or courier.
The PBTI may, at its discretion, extend the deadline for submission of EOI by amending
the EOI Document, in which case, all rights and obligations of PBTI and the bidders
previously subjected to the deadline shall thereafter be subjected to the same deadline
so extended.
D. Clarification of EOI
During evaluation of EOI, PBTI may, at its discretion, give opportunity to the Bidder(s)
for clarification of points raised by the EOI evaluation committee on its EOI submitted.
The request for clarification and the response shall be in writing, either through email or
fax or by post.
Store &Purchase Officer For Chief Executive Officer,
Punjab Biotechnology Incubator
Page 10 of 13
Annexure –I
FORMAT FOR MANUFACTURER’S/PRINCIPLE SUPPLIER’S AUTHORISATION FORM
To,
PUNJAB BIOTECHNOLOGY INCUBATOR (A State Govt. Undertaking) SCO 7-8, Phase-V, S.A.S., Nagar (Mohali) 160 059
Dear Sir, Sub. : Expression of Interest for the Pre-Qualification of Vendors for the Designing,
Engineering, Supply, Layout At Site, Installation, Testing And Commissioning of Online UPS 60 KVA X 3 No. including Ancillary Services on Turnkey basis for Food & Drug Laboratory of FDA, Punjab at Kharar.
We, ____________________________, who are established and reputed manufacturers/Principle supplier of UPS (Brand) _____________________, having our office at __________________________________, hereby authorize M/s. _____________________ _________________________________________ [name & address of tenderer] to bid, negotiate, conclude and execute work cited above as subject. We hereby extend our full guarantee and warranty as per the terms and conditions of tender for the goods and services offered for supply against this invitation for bid by the above tenderer.
Yours faithfully,
[name] for and on behalf of M/s. ___________________
[name of manufacturer/Principle Supplier]
Note: This letter of authorization should be on the letterhead of the manufacturing concern/
Principle supplier and should be signed by a person competent and having the power of
attorney to bind the manufacturer/ Principle supplier.
Page 11 of 13
ANNEXURE –II General Information:
S.No. Particulars
1. Name of Firm/Tenderer/Company (in block letters)
2. Permanent Address & Telephone No./Fax/E-mail
3. Year of incorporation of the Firm/Company
4. Contact Person’s: Telephone/Mobile No.
5. Details of infrastructure, persons employed, number of offices/branches available (attach separate sheet)
[Attach complete profile of the company including the desired information]
6 An affidavit duly certified by a Notary [Attach as enclosure & refer here] that the Partners of the firm sole Proprietor or Company has never been black Listed/ not involved in any Police Case/ Vigilance enquiry pending or ever been punished by any Hon'ble Court.
[Attach as enclosure]
7 Details of ESIC Registration with Date
8 Details of EPF Registration with Date
Page 12 of 13
Annexure –III
Pre-qualification requirement:
Sr.no.
Eligibility Criteria Documents to be submitted Compliance and evidence is enclosed ( Yes/ No ) mention page nos of the enclosures
1 The Applicant Company should be a company registered in India under the Indian Companies Act of 1956
The registration no. of the firm /company along with Sales Tax no./Certificate of Incorporation. Photocopy of TAN, PAN, VAT No., Service Tax regd. No. etc. and Tax clearance certificates
2 The Applicant Company should be authorized distributor / authorized dealer of reputed UPS Manufacturers
Proof should be enclosed like certificate issued by UPS manufacturers
3 The Applicant Company Should be in the business of UPS (20 KVA or above) for at least past 5 years and should have executed at least three (03) similar work of estimated cost (Rs.35 Lacs) for each of value not less than 40% of the estimated cost or two similar works each of value not less than 60% of the estimated cost or one similar work of value not less than 80% of the estimated cost or more during the last five (05) years ending last day of previous month (i.e. February, 2017)). (Similar work means: Supply, installation, testing and commissioning of UPS system with the capacity 20 KVA or above).
List with documentary evidence. Proof should be enclosed like order copy or installation certificate / satisfactory certificate etc. (preferably of Govt. Institutions/Organizations)
4 Annual Turnover in UPS business should be minimum Rs.5 Crores for the last three years. The company should be in profit during the last three years i.e. 2013-14, 2014-15 and 2015-2016 from UPS Business.
Audited Balance Sheet and P & L Account certified by Chartered Accountant for last 3 years.
5 Solvency Certificate for Rs. 5.00 crore
Certificate issued by any Scheduled Bank during the last six months
Page 13 of 13
6 The vendor should have Capability to attend the UPS complaints within 12 hours to 24 hours for this the vendor should have its Service Centres preferably in Tri-city of Mohali/ Chandigarh/ Punchkula
Proof should be enclosed along with the address and phone number.
top related